All the devices that used to use system_clock_scale have now been
converted to use Clock inputs instead, so the global is no longer
needed; remove it and all the code that sets it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210812093356.1946-26-peter.maydell@linaro.org
The stellaris-gptm timer currently uses system_clock_scale for one of
its timer modes where the timer runs at the CPU clock rate. Make it
use a Clock input instead.
We don't try to make the timer handle changes in the clock frequency
while the downcounter is running. This is not a change in behaviour
from the previous system_clock_scale implementation -- we will pick
up the new frequency only when the downcounter hits zero. Handling
dynamic clock changes when the counter is running would require state
that the current gptm implementation doesn't have.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20210812093356.1946-25-peter.maydell@linaro.org
The implementation of the Stellaris general purpose timer module
device stellaris-gptm is currently in the same source file as the
board model. Split it out into its own source file in hw/timer.
Apart from the new file comment headers and the Kconfig and
meson.build changes, this is just code movement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Message-id: 20210812093356.1946-24-peter.maydell@linaro.org
The v7M systick timer can be programmed to run from either of
two clocks:
* an "external reference clock" (when SYST_CSR.CLKSOURCE == 0)
* the main CPU clock (when SYST_CSR.CLKSOURCE == 1)
Our implementation currently hardwires the external reference clock
to be 1MHz, and allows boards to set the main CPU clock frequency via
the global 'system_clock_scale'. (Most boards set that to a constant
value; the Stellaris boards allow the guest to reprogram it via the
board-specific RCC registers).
As the first step in converting this to use the Clock infrastructure,
add input clocks to the systick device for the reference clock and
the CPU clock. The device implementation ignores them; once we have
made all the users of the device correctly wire up the new Clocks we
will switch the implementation to use them and ignore the old
system_clock_scale.
This is a migration compat break for all M-profile boards, because of
the addition of the new clock objects to the vmstate struct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-6-peter.maydell@linaro.org
Add the usual-style QEMU interface comment documenting what
properties, etc, this device exposes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20210812093356.1946-5-peter.maydell@linaro.org
Add support for the Ibex timer. This is used with the RISC-V
mtime/mtimecmp similar to the SiFive CLINT.
We currently don't support changing the prescale or the timervalue.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 716fdea2244515ce86a2c46fe69467d013c03147.1624001156.git.alistair.francis@wdc.com
The include/hw/hw.h header only has a prototype for hw_error(),
so it does not make sense to include this in files that do not
use this function.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210326151848.2217216-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The SSE-300 includes some timers which are a different kind to
those in the SSE-200. Model them.
These timers are documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-13-peter.maydell@linaro.org
The SSE-300 includes a counter module; implement a model of it.
This counter is documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-12-peter.maydell@linaro.org
Now no users are setting the frq properties on the CMSDK timer,
dualtimer, watchdog or ARMSSE SoC devices, we can remove the
properties and the struct fields that back them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-25-peter.maydell@linaro.org
Message-id: 20210121190622.22000-25-peter.maydell@linaro.org
The old-style convenience function cmsdk_apb_timer_create() for
creating CMSDK_APB_TIMER objects is used in only two places in
mps2.c. Most of the rest of the code in that file uses the new
"initialize in place" coding style.
We want to connect up a Clock object which should be done between the
object creation and realization; rather than adding a Clock* argument
to the convenience function, convert the timer creation code in
mps2.c to the same style as is used already for the watchdog,
dualtimer and other devices, and delete the now-unused convenience
function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-13-peter.maydell@linaro.org
Message-id: 20210121190622.22000-13-peter.maydell@linaro.org
As the first step in converting the CMSDK_APB_DUALTIMER device to the
Clock framework, add a Clock input. For the moment we do nothing
with this clock; we will change the behaviour from using the pclk-frq
property to using the Clock once all the users of this device have
been converted to wire up the Clock.
We take the opportunity to correct the name of the clock input to
match the hardware -- the dual timer names the clock which drives the
timers TIMCLK. (It does also have a 'pclk' input, which is used only
for the register and APB bus logic; on the SSE-200 these clocks are
both connected together.)
This is a migration compatibility break for machines mps2-an385,
mps2-an386, mps2-an500, mps2-an511, mps2-an505, mps2-an521, musca-a,
musca-b1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-9-peter.maydell@linaro.org
Message-id: 20210121190622.22000-9-peter.maydell@linaro.org
As the first step in converting the CMSDK_APB_TIMER device to the
Clock framework, add a Clock input. For the moment we do nothing
with this clock; we will change the behaviour from using the pclk-frq
property to using the Clock once all the users of this device have
been converted to wire up the Clock.
Since the device doesn't already have a doc comment for its "QEMU
interface", we add one including the new Clock.
This is a migration compatibility break for machines mps2-an505,
mps2-an521, musca-a, musca-b1.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-8-peter.maydell@linaro.org
Message-id: 20210121190622.22000-8-peter.maydell@linaro.org
The state struct for the CMSDK APB timer device doesn't follow our
usual naming convention of camelcase -- "CMSDK" and "APB" are both
acronyms, but "TIMER" is not so should not be all-uppercase.
Globally rename the struct to "CMSDKAPBTimer" (bringing it into line
with CMSDKAPBWatchdog and CMSDKAPBDualTimer; CMSDKAPBUART remains
as-is because "UART" is an acronym).
Commit created with:
perl -p -i -e 's/CMSDKAPBTIMER/CMSDKAPBTimer/g' hw/timer/cmsdk-apb-timer.c include/hw/arm/armsse.h include/hw/timer/cmsdk-apb-timer.h
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210128114145.20536-7-peter.maydell@linaro.org
Message-id: 20210121190622.22000-7-peter.maydell@linaro.org
This patch makes NPCM7XX Timer to use a the timer clock generated by the
CLK module instead of the magic number TIMER_REF_HZ.
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210108190945.949196-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The armv7m systick timer is a 24-bit decrementing, wrap-on-zero,
clear-on-write counter. Our current implementation has various
bugs and dubious workarounds in it (for instance see
https://bugs.launchpad.net/qemu/+bug/1872237).
We have an implementation of a simple decrementing counter
and we put a lot of effort into making sure it handles the
interesting corner cases (like "spend a cycle at 0 before
reloading") -- ptimer.
Rewrite the systick timer to use a ptimer rather than
a raw QEMU timer.
Unfortunately this is a migration compatibility break,
which will affect all M-profile boards.
Among other bugs, this fixes
https://bugs.launchpad.net/qemu/+bug/1872237 :
now writes to SYST_CVR when the timer is enabled correctly
do nothing; when the timer is enabled via SYST_CSR.ENABLE,
the ptimer code will (because of POLICY_NO_IMMEDIATE_RELOAD)
arrange that after one timer tick the counter is reloaded
from SYST_RVR and then counts down from there, as the
architecture requires.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201015151829.14656-3-peter.maydell@linaro.org
The watchdog is part of NPCM7XX's timer module. Its behavior is
controlled by the WTCR register in the timer.
When enabled, the watchdog issues an interrupt signal after a pre-set
amount of cycles, and issues a reset signal shortly after that.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: deleted blank line at end of npcm_watchdog_timer-test.c]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This peripheral has 1 free-running timer and 4 compare registers.
Only the free-running timer is implemented. Add support the
COMPARE registers (each register is wired to an IRQ).
Reference: "BCM2835 ARM Peripherals" datasheet [*]
chapter 12 "System Timer":
The System Timer peripheral provides four 32-bit timer channels
and a single 64-bit free running counter. Each channel has an
output compare register, which is compared against the 32 least
significant bits of the free running counter values. When the
two values match, the system timer peripheral generates a signal
to indicate a match for the appropriate channel. The match signal
is then fed into the interrupt controller.
This peripheral is used since Linux 3.7, commit ee4af5696720
("ARM: bcm2835: add system timer").
[*] https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20201010203709.3116542-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The variable holding the CTRL_STATUS register is misnamed
'status'. Rename it 'ctrl_status' to make it more obvious
this register is also used to control the peripheral.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the BCM2835_SYSTIMER_COUNT definition instead of the
magic '4' value.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201010203709.3116542-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM730 and NPCM750 SoCs have three timer modules each holding five
timers and some shared registers (e.g. interrupt status).
Each timer runs at 25 MHz divided by a prescaler, and counts down from a
configurable initial value to zero. When zero is reached, the interrupt
flag for the timer is set, and the timer is disabled (one-shot mode) or
reloaded from its initial value (periodic mode).
This implementation is sufficient to boot a Linux kernel configured for
NPCM750. Note that the kernel does not seem to actually turn on the
interrupts.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Alexander Bulekov <alxndr@bu.edu>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-id: 20200911052101.2602693-4-hskinnemoen@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move typedef closer to the type check macros, to make it easier
to convert the code to OBJECT_DEFINE_TYPE() in the future.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-19-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The macro definition had an extra semicolon. This was never
noticed because the macro was only being used where it didn't
make a difference.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
These were designed to facilitate testing but should provide enough
function to be useful in other contexts. Only a subset of the functions
of each peripheral is implemented, mainly due to the lack of a standard
way to handle electrical connections (like GPIO pins).
[AM: Remove word 'Atmel' from filenames and all elements of code]
Suggested-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Signed-off-by: Sarah Harris <S.E.Harris@kent.ac.uk>
Signed-off-by: Ed Robbins <E.J.C.Robbins@kent.ac.uk>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[rth: Squash info mtree fixes and a file rename from f4bug]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[PMD: Use qemu_log_mask(LOG_UNIMP), replace goto by return]
Signed-off-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20200705140315.260514-21-huth@tuxfamily.org>
[PMD: Check cpu-frequency-hz property in realize()]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
renesas_cmt: 16bit compare match timer modules.
This part use many renesas's CPU.
Hardware manual.
https://www.renesas.com/us/en/doc/products/mpumcu/doc/rx_family/r01uh0033ej0140_rx62n.pdf
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200224141923.82118-16-ysato@users.sourceforge.jp>
[PMD: Split from TMR, filled VMStateField for migration]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
renesas_tmr: 8bit timer modules.
This part use many renesas's CPU.
Hardware manual.
https://www.renesas.com/us/en/doc/products/mpumcu/doc/rx_family/r01uh0033ej0140_rx62n.pdf
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200224141923.82118-16-ysato@users.sourceforge.jp>
[PMD: Split from CMT, filled VMStateField for migration]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Extract timer definitions to 'hw/timer/tmu012.h'.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
The NRF51 series SoC have 3 timer peripherals, each having
4 counters. To help differentiate which peripheral is accessed,
display the timer ID in the trace events.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200504072822.18799-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move RTC devices under the hw/rtc/ subdirectory.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-12-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The M48T59 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-5-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The MC146818 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Use copyright statement from 80cabfad16 for "hw/rtc/mc146818rtc.h".
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191003230404.19384-4-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The PL031 is a Real Time Clock, not a timer.
Move it under the hw/rtc/ subdirectory.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The AST2600 timer replaces control register 2 with a interrupt status
register. It is set by hardware when an IRQ occurs and cleared by
software.
Modify the vmstate version to take into account the new fields.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-8-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 timer has a third control register that is used to
implement a set-to-clear feature for the main control register.
On the AST2600, it is not configurable via 0x38 (control register 3)
as it is on the AST2500.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 timer has a third control register that is used to
implement a set-to-clear feature for the main control register.
This models the behaviour expected by the AST2500 while maintaining
the same behaviour for the AST2400.
The vmstate version is not increased yet because the structure is
modified again in the following patches.
Based on previous work from Joel Stanley.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The most important changes will be on the register range 0x34 - 0x3C
memops. Introduce class read/write operations to handle the
differences between SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the mss-timer code away from bottom-half based ptimers to
the new transaction-based ptimer API. This just requires adding
begin/commit calls around the various places that modify the ptimer
state, and using the new ptimer_init() function to create the timer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20191008171740.9679-20-peter.maydell@linaro.org
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
In my "build everything" tree, changing hw/qdev-properties.h triggers
a recompile of some 2700 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Many places including hw/qdev-properties.h (directly or via hw/qdev.h)
actually need only hw/qdev-core.h. Include hw/qdev-core.h there
instead.
hw/qdev.h is actually pointless: all it does is include hw/qdev-core.h
and hw/qdev-properties.h, which in turn includes hw/qdev-core.h.
Replace the remaining uses of hw/qdev.h by hw/qdev-properties.h.
While there, delete a few superfluous inclusions of hw/qdev-core.h.
Touching hw/qdev-properties.h now recompiles some 1200 objects.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Daniel P. Berrangé" <berrange@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190812052359.30071-22-armbru@redhat.com>
Peter Maydell
Alistair Francis
Thomas Huth
Hao Wu
Philippe Mathieu-Daudé
Eduardo Habkost
Havard Skinnemoen
Michael Rolnik
Yoshinori Sato
Markus Armbruster
Philippe Mathieu-Daudé
Cédric Le Goater