Some functions are now only used in arm_gic.c, put them static. Some of
them where only used by the NVIC implementation and are not used
anymore, so remove them.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-4-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement GICD_ISACTIVERn and GICD_ICACTIVERn registers in the GICv2.
Those registers allow to set or clear the active state of an IRQ in the
distributor.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-3-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for the virtualization extensions implementation,
refactor the name of the functions and macros that act on the GIC
distributor to make that fact explicit. It will be useful to
differentiate them from the ones that will act on the virtual
interfaces.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-2-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICD_ITARGETSR implementation still has some 11MPCore behaviour
that we were incorrectly using in our GICv1 and GICv2 implementations
for the case where the interrupt number is less than GIC_INTERNAL.
The desired behaviour here is:
* for 11MPCore: RAZ/WI for irqs 0..28; read a number matching the
CPU doing the read for irqs 29..31
* for GICv1 and v2: RAZ/WI if uniprocessor; otherwise read a
number matching the CPU doing the read for all irqs < 32
Stop squashing GICD_ITARGETSR to 0 for IRQs 0..28 unless this
is an 11MPCore GIC.
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180712154152.32183-3-peter.maydell@linaro.org
In gic_deactivate_irq() the interrupt number comes from the guest
(on a write to the GICC_DIR register), so we need to sanity check
that it isn't out of range before we use it as an array index.
Handle this in a similar manner to the check we do in
gic_complete_irq() for the GICC_EOI register.
The array overrun is not disastrous because the calling code
uses (value & 0x3ff) to extract the interrupt field, so the
only out-of-range values possible are 1020..1023, which allow
overrunning only from irq_state[] into the following
irq_target[] array which the guest can already manipulate.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180712154152.32183-2-peter.maydell@linaro.org
When C_CTRL.CBPR is 1, the Non-Secure view of C_BPR is altered:
- A Non-Secure read of C_BPR should return the BPR value plus 1,
saturated to 7,
- A Non-Secure write should be ignored.
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-6-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed comment typo]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When determining the group priority of a group 1 IRQ, if C_CTRL.CBPR is
0, the non-secure BPR value is used. However, this value must be
incremented by one so that it matches the secure world number of
implemented priority bits (NS world has one less priority bit compared
to the Secure world).
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-5-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: add assert, as the gicv3 code has]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When there is no active interrupts in the GIC, a read to the C_RPR
register should return the value of the "Idle priority", which is either
the maximum value an IRQ priority field can be set to, or 0xff.
Since the QEMU GIC model implements all the 8 priority bits, the Idle
priority is 0xff.
Internally, when there is no active interrupt, the running priority
value is 0x100. The gic_get_running_priority function returns an uint8_t
and thus, truncate this value to 0x00 when returning it. This is wrong since
a value of 0x00 correspond to the maximum possible priority.
This commit fixes the returned value when the internal value is 0x100.
Note that it is correct for the Non-Secure view to return 0xff even
though from the NS world point of view, only 7 priority bits are
implemented. The specification states that the Idle priority can be 0xff
even when not all the 8 priority bits are implemented. This has been
verified against a real GICv2 hardware on a Xilinx ZynqMP based board.
Regarding the ARM11MPCore version of the GIC, the specification is not
clear on that point, so this commit does not alter its behavior.
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-4-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the GIC, when an IRQ is acknowledged, its state goes from "pending"
to:
- "active" if the corresponding IRQ pin has been de-asserted
- "active and pending" otherwise.
The GICv2 manual states that when a IRQ becomes active (or active and
pending), the GIC should either signal another (higher priority) IRQ to
the CPU if there is one, or de-assert the CPU IRQ pin.
The current implementation of the GIC in QEMU does not check if the
IRQ is already active when looking for pending interrupts with
sufficient priority in gic_update(). This can lead to signaling an
interrupt that is already active.
This usually happens when splitting priority drop and interrupt
deactivation. On priority drop, the IRQ stays active until deactivation.
If it becomes pending again, chances are that it will be incorrectly
selected as best_irq in gic_update().
This commit fixes this by checking if the IRQ is not already active when
looking for best_irq in gic_update().
Note that regarding the ARM11MPCore GIC version, the corresponding
manual is not clear on that point, but it has has no priority
drop/interrupt deactivation separation, so this case should not happen.
Signed-off-by: Luc MICHEL <luc.michel@git.antfield.fr>
Message-id: 20180119145756.7629-3-luc.michel@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICv2 specification says that reserved register addresses
must RAZ/WI; now that we implement external abort handling
for Arm CPUs this means we must return MEMTX_OK rather than
MEMTX_ERROR, to avoid generating a spurious guest data abort.
Cc: qemu-stable@nongnu.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1513183941-24300-3-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
When running with KVM enabled, you can choose between emulating the
gic in kernel or user space. If the kernel supports in-kernel virtualization
of the interrupt controller, it will default to that. If not, if will
default to user space emulation.
Unfortunately when running in user mode gic emulation, we miss out on
interrupt events which are only available from kernel space, such as the timer.
This patch leverages the new kernel/user space pending line synchronization for
timer events. It does not handle PMU events yet.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1498577737-130264-1-git-send-email-agraf@suse.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While I was debugging the icount issues I realised a bunch of the
messages look quite similar. I've fixed this by including __func__ in
the debug print. At the same time I move the a modern if (GATE) style
printf which ensures the compiler can check for format string errors
even if the code gets optimised away in the non-DEBUG_GIC case.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now that the NVIC is its own separate implementation, we can
clean up the GIC code by removing REV_NVIC and conditionals
which use it.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
According to ARM DUI 0552A 4.2.10. NVIC set pending status
also for disabled interrupts. Correct the logic for
when interrupts are marked pending both on input level
transition and when interrupts are dismissed, to match
the NVIC behaviour rather than the 11MPCore GIC.
Signed-off-by: Marcin Krzeminski <marcin.krzeminski@nokia.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Treat non-secure accesses to registers and bits in registers of secure
interrupts as RAZ/WI.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Message-id: 1464273945-2055-1-git-send-email-jens.wiklander@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are obviously critical to understanding interrupt delivery:
gic_enable_irq
gic_disable_irq
gic_set_irq (inbound irq from device models)
gic_update_set_irq (outbound irq to CPU)
gic_acknowledge_irq
The only one that I think might raise eyebrows is gic_update_bestirq, but I've
(sadly) debugged problems that ended up being caused by unexpected priorities.
Knowing that the GIC has an irq ready, but doesn't deliver to the CPU due to
priority, has also proven important.
Signed-off-by: Hollis Blanchard <hollis_blanchard@mentor.com>
Message-id: 1461252281-22399-1-git-send-email-hollis_blanchard@mentor.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The GICv2 introduces a new CPU interface register GICC_DIR, which
allows an OS to split the "priority drop" and "deactivate interrupt"
parts of interrupt completion. Implement this register.
(Note that the register is at offset 0x1000 in the CPU interface,
which means it is on a different 4K page from all the other registers.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Message-id: 1456854176-7813-1-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Update the GIC ID registers (registers above 0xfe0) based on the GIC
revision instead of using the sames values for all GIC implementations.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Message-id: 629e7fa5d47f2800e51cc1f18d12635f1eece349.1453333840.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Upon activating an interrupt, set the corresponding priority bit in the
APR/NSAPR registers without touching the currently set bits. In the event
of nested interrupts, the GIC will then have the information it needs to
restore the priority of the pre-empted interrupt once the higher priority
interrupt finishes execution.
Signed-off-by: François Baldassari <francois@pebble.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
arm_gic.c retrieves CPU number using either NUM_CPU(s) or s->num_cpu.
Such mixed-uses make source code inconsistent. This patch removes
NUM_CPU(s), which was defined for MPCore tweak long ago, and instead
favors s->num_cpu. The source is more consistent after this small tweak.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Message-id: 1446744293-32365-1-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A number of source files have statements accidentally
terminated by a double semicolon - eg 'foo = bar;;'.
This is harmless but a mistake none the less.
The tcg/ia64/tcg-target.c file is whitelisted because
it has valid use of ';;' in a comment containing assembly
code.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Although we were correctly handling interrupts becoming active
and then inactive, we weren't actually exposing this to the guest
by setting the 'active' flag for the interrupt, so reads
of GICD_ICACTIVERn and GICD_ISACTIVERn would generally incorrectly
return zeroes. Correct this oversight.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-6-git-send-email-peter.maydell@linaro.org
The running_irq and last_active arrays represent state which
doesn't exist in a real hardware GIC. The only thing we use
them for is updating the running priority when an interrupt
is completed, but in fact we can use the active-priority
registers to do this. The running priority is always the
priority corresponding to the lowest set bit in the active
priority registers, because only one interrupt at any
particular priority can be active at once.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-5-git-send-email-peter.maydell@linaro.org
A GICv2 has both GICC_APR<n> and GICC_NSAPR<n> registers, with
the latter holding the active priority bits for Group 1 interrupts
(usually Nonsecure interrupts), and the Nonsecure view of the
GICC_APR<n> is the second half of the GICC_NSAPR<n> registers.
Turn our half-hearted implementation of APR<n> into a proper
implementation of both APR<n> and NSAPR<n>:
* Add the underlying state for NSAPR<n>
* Make sure APR<n> aren't visible for pre-GICv2
* Implement reading of NSAPR<n>
* Make non-secure reads of APR<n> behave correctly
* Implement writing to APR<n> and NSAPR<n>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-4-git-send-email-peter.maydell@linaro.org
Priority values for the GIC are divided into a "group priority"
and a "subpriority" (with the division being determined by the
binary point register). The running priority is only determined
by the group priority of the active interrupts, not the
subpriority. In particular, this means that there can't be more
than one active interrupt at any particular group priority.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-3-git-send-email-peter.maydell@linaro.org
Extracted duplicated initialization code from SW-emulated and KVM GIC
implementations and put into gic_init_irqs_and_mmio()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-id: 8ea5b2781ef39cb5989420987fc73c70e377687d.1438758065.git.p.fedin@samsung.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch fixes so that gic_update always updates all the cores with
new pending irq states. If the function returns early it is possible
to get interrupts that has already been acknowledged.
Signed-off-by: Johan Karlsson <johan.karlsson@enea.com>
[PMM: rebased to apply to current master]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support to gic_update() for determining the current IRQ
and FIQ status when interrupt grouping is supported. This
simply requires that instead of always raising IRQ we
check the group of the highest priority pending interrupt
and the GICC_CTLR.FIQEn bit to see whether we should raise
IRQ or FIQ.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1430502643-25909-15-git-send-email-peter.maydell@linaro.org
Grouping (GICv2) and Security Extensions change the behavior of IAR
reads. Acknowledging Group0 interrupts is only allowed from Secure
state and acknowledging Group1 interrupts from Secure state is only
allowed if AckCtl bit is set.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-14-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-14-git-send-email-greg.bellows@linaro.org
[PMM: simplify significantly by reusing the existing
gic_get_current_pending_irq() rather than reimplementing the
same logic here]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Grouping (GICv2) and Security Extensions change the behavior of EOIR
writes. Completing Group0 interrupts is only allowed from Secure state.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-13-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-13-git-send-email-greg.bellows@linaro.org
[PMM: Rather than go to great lengths to ignore the UNPREDICTABLE case
of a Secure EOI of a Group1 (NS) irq with AckCtl == 0, we just let
it fall through; add a comment about it.]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Grouping (GICv2) and Security Extensions change the behaviour of reads
of the highest priority pending interrupt register (ICCHPIR/GICC_HPPIR).
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-12-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-12-git-send-email-greg.bellows@linaro.org
[PMM: make utility fn static; coding style fixes; AckCtl has an effect
for GICv2 without security extensions as well; removed checks on enable
bits because these are done when we set current_pending[cpu]]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GICs with Security Extensions restrict the non-secure view of the
interrupt priority and priority mask registers.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-11-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-15-git-send-email-greg.bellows@linaro.org
[PMM: minor code tweaks; fixed missing masking in gic_set_priority_mask
and gic_set_priority]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For GICs with Security Extensions Non-secure reads have a restricted
view on the current running priority.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-10-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-11-git-send-email-greg.bellows@linaro.org
[PMM: make function static, minor comment tweak]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ICCICR/GICC_CTLR is banked in GICv1 implementations with Security
Extensions or in GICv2 in independent from Security Extensions.
This makes it possible to enable forwarding of interrupts from
the CPU interfaces to the connected processors for Group0 and Group1.
We also allow to set additional bits like AckCtl and FIQEn by changing
the type from bool to uint32. Since the field does not only store the
enable bit anymore and since we are touching the vmstate, we use the
opportunity to rename the field to cpu_ctlr.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-9-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-9-git-send-email-greg.bellows@linaro.org
[PMM: rewrote to store state in a single uint32_t rather than
keeping the NS and S banked variants separate; this considerably
simplifies the get/set functions]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This register is banked in GICs with Security Extensions. Storing the
non-secure copy of BPR in the abpr, which is an alias to the non-secure
copy for secure access. ABPR itself is only accessible from secure state
if the GIC implements Security Extensions.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-8-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-10-git-send-email-greg.bellows@linaro.org
[PMM: rewrote to fix style issues and correct handling of GICv2
without security extensions]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ICDDCR/GICD_CTLR is banked if the GIC has the security extensions,
and the S (or only) copy has separate enable bits for Group0 and
Group1 enable if the GIC implements interrupt groups.
EnableGroup0 (Bit [1]) in GICv1 is architecturally IMPDEF. Since this
bit (Enable Non-secure) is present in the integrated GIC of the Cortex-A9
MPCore, we support this bit in our GICv1 implementation too.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-7-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-8-git-send-email-greg.bellows@linaro.org
[PMM: rewritten to store the state in a single s->ctlr uint32,
with the NS register handled as an alias of bit 1 in that value;
added vmstate version bump]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Interrupt Group Registers allow the guest to configure interrupts
into one of two groups, where Group0 are higher priority and may
be routed to IRQ or FIQ, and Group1 are lower priority and always
routed to IRQ. (In a GIC with the security extensions Group0 is
Secure interrupts and Group 1 is NonSecure.)
The GICv2 always supports interrupt grouping; the GICv1 does only
if it implements the security extensions.
This patch implements the ability to read and write the registers;
the actual functionality the bits control will be added in a
subsequent patch.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-5-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-7-git-send-email-greg.bellows@linaro.org
[PMM: bring GIC_*_GROUP macros into line with the others, ie a
simple SET/CLEAR/TEST rather than GROUP0/GROUP1;
utility gic_has_groups() function;
minor style fixes;
bump vmstate version]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the GIC's MMIO callback functions to the read_with_attrs
and write_with_attrs functions which provide MemTxAttrs. This will
allow the GIC to correctly handle secure and nonsecure register
accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1430502643-25909-4-git-send-email-peter.maydell@linaro.org
Add a QOM property which allows the GIC Security Extensions to be
enabled. These are an optional part of the GICv1 and GICv2 architecture.
This commit just adds the property and some sanity checks that it
is only enabled on GIC revisions that support it.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-3-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-5-git-send-email-greg.bellows@linaro.org
[PMM: changed property name, added checks that it isn't set for
older GIC revisions or if using the KVM VGIC; reworded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create the outbound FIQ lines from the GIC to the CPUs; these are
used if the GIC has security extensions or grouping support.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-2-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-2-git-send-email-greg.bellows@linaro.org
[PMM: added FIQ lines to kvm-arm-gic so its interface is the same;
tweaked commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This removes num_irq parameter from gic_init_irqs_and_distributor as it is not
used.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1412859651-15060-1-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Take IRQ target mask into account when determining the highest priority
pending interrupt.
Signed-off-by: Sergey Fedorov <serge.fdrv@gmail.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1407947471-26981-1-git-send-email-serge.fdrv@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only SGIs must be WI, done by forcing them to their default
(edge-triggered).
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-4-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Setting the model is only available in pre-v1 GIC models.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-3-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICD_ICFGR register covers 4 interrupts per byte.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-2-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Luc Michel
Peter Maydell
Philippe Mathieu-Daudé
Luc MICHEL
Alexander Graf
Alex Bennée
Michael Davidsaver
Marcin Krzeminski
Jens Wiklander
Paolo Bonzini
Hollis Blanchard
Markus Armbruster
Alistair Francis
François Baldassari
Wei Huang
Daniel P. Berrange
Pavel Fedin
Johan Karlsson
Fabian Aggeler
Stefan Weil
KONRAD Frederic
Sergey Fedorov
Adam Lackorzynski