With the new CMB logic in place, bump the implemented specification
version to v1.4 by default.
This requires adding the setting the CNTRLTYPE field and modifying the
VWC field since 0x00 is no longer a valid value for bits 2:1.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Implement v1.4 logic for configuring the Controller Memory Buffer. By
default, the v1.4 scheme will be used (CMB must be explicitly enabled by
the host), so drivers that only support v1.3 will not be able to use the
CMB anymore.
To retain the v1.3 behavior, set the boolean 'legacy-cmb' nvme device
parameter.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Padmakar Kalghatgi <p.kalghatgi@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for the PMRMSCL and PMRMSCU MMIO registers. This allows
adding RDS/WDS support for PMR as well.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Naveen Nagar <naveen.n1@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The PMR should not be enabled at boot up. Disable the PMR MemoryRegion
initially and implement MMIO for PMRCTL, allowing the host to enable the
PMR explicitly.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The controller registers are initially zero. Remove the redundant
zeroing.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Use the correct field names.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
With BAR 4 now free to use, allow PMR and CMB to be enabled
simultaneously.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
In the interest of supporting both CMB and PMR to be enabled on the same
device, move the MSI-X table and pending bit array out of BAR 4 and into
BAR 0.
This is a simplified version of the patch contributed by Andrzej
Jakowski (see [1]). Leaving the CMB at offset 0 removes the need for
changes to CMB address mapping code.
[1]: https://lore.kernel.org/qemu-devel/20200729220107.37758-3-andrzej.jakowski@linux.intel.com/
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This patch sets CMBS bit in controller capabilities register when user
configures NVMe driver with CMB support, so capabilites are correctly
reported to guest OS.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@linux.intel.com>
Reviewed-by: Maxim Levitsky <mlevitsky@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
64 bit registers like ASQ and ACQ should be writable by both a hi/lo 32
bit write combination as well as a plain 64 bit write. The spec does not
define ordering on the hi/lo split, but the code currently assumes that
the low order bits are written first. Additionally, the code does not
consider that another address might already have been written into the
register, causing the OR'ing to result in a bad address.
Fix this by explicitly overwriting only the low or high order bits for
32 bit writes.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add the size of the mmio read/write to the trace event.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
During smart critical warning injection by setting property from QMP
command, also try to trigger asynchronous event.
Suggested by Keith, if a event has already been raised, there is no
need to enqueue the duplicate event any more.
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
[k.jensen: fix typo in commit message]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
There is a very low probability that hitting physical NVMe disk
hardware critical warning case, it's hard to write & test a monitor
agent service.
For debugging purposes, add a new 'smart_critical_warning' property
to emulate this situation.
The orignal version of this change is implemented by adding a fixed
property which could be initialized by QEMU command line. Suggested
by Philippe & Klaus, rework like current version.
Test with this patch:
1, change smart_critical_warning property for a running VM:
#virsh qemu-monitor-command nvme-upstream '{ "execute": "qom-set",
"arguments": { "path": "/machine/peripheral-anon/device[0]",
"property": "smart_critical_warning", "value":16 } }'
2, run smartctl in guest
#smartctl -H -l error /dev/nvme0n1
=== START OF SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
- volatile memory backup device has failed
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
According to NVM Express v1.4, Section 5.14.1.2 ("SMART / Health
Information"), introduce bit 5 for "Persistent Memory Region has become
read-only or unreliable".
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
[k.jensen: minor brush ups in commit message]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The zone write pointer is unconditionally advanced, even for write
faults. Make sure that the zone is always transitioned to Full if the
write pointer reaches zone capacity.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_ns_setup() finally does not have nothing to do with NvmeCtrl
instance.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
In NVMe, namespace is being attached to process I/O. We register NVMe
namespace to a controller via nvme_register_namespace() during
nvme_ns_setup(). This is main reason of receiving NvmeCtrl object
instance to this function to map the namespace to a controller.
To make namespace instance more independent, it should be split into two
parts: setup and register. This patch split them into two differnt
parts, and finally nvme_ns_setup() does not have nothing to do with
NvmeCtrl instance at all.
This patch is a former patch to introduce NVMe subsystem scheme to the
existing design especially for multi-path. In that case, it should be
split into two to make namespace independent from a controller.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Removed no longer used aregument NvmeCtrl object in nvme_ns_init_blk().
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Volatile Write Cache(VWC) feature is set in nvme_ns_setup() in the
initial time. This feature is related to block device backed, but this
feature is controlled in controller level via Set/Get Features command.
This patch removed dependency between nvme and nvme-ns to manage the VWC
flag value. Also, it open coded the Get Features for VWC to check all
namespaces attached to the controller, and if false detected, return
directly false.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
[k.jensen: report write cache preset if present on ANY namespace]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_ns_init_zoned() has no use for given NvmeCtrl object.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
TP 4053 says (in section 2.3.1.1) -
... if a Zone Append command specifies a ZSLBA that is not the lowest
logical block address in that zone, then the controller shall abort
that command with a status code of Invalid Field In Command.
In the code, Zone Invalid Write is returned instead, fix this.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_io_cmd already checks if the namespace supports the Zone Append
command, so the removed check is dead code.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Add missing string representations for a couple of new commands.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
The zoned command set specification states that "All logical blocks in a
zone *shall* be marked as deallocated when [the zone is reset]". Since
the device guarantees 0x00 to be read from deallocated blocks we have to
issue a pwrite_zeroes since we cannot be sure that a discard will do
anything. But typically, this will be achieved with an efficient
unmap/discard operation.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Align with existing style and use a typedef for header-file enums.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Implicitly and explicitly opended zones are always bulk processed
together, so merge the two processing masks.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
A shutdown is only about flushing stuff. It is the host that should
delete any queues, so do not perform a reset here.
Also, on shutdown, make sure that the PMR is flushed if in use.
Fixes: 368f4e752cf9 ("hw/block/nvme: Process controller reset and shutdown differently")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
The device uses the BDRV_BLOCK_ZERO flag to determine the "deallocated"
status of logical blocks. Since the zoned namespaces command set
specification defines that logical blocks SHALL be marked as deallocated
when the zone is in the Empty or Offline states, DULBE can only be
supported if the zone size is a multiple of the calculated deallocation
granularity (reported in NPDG) which depends on the underlying block
device cluster size (if applicable) or the configured
discard_granularity.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit 1c0c2163aa ("hw/block/nvme: verify msix_init_exclusive_bar()
return value") had the unintended effect of breaking support on
several platforms not supporting MSI-X.
Still check for errors, but only report that MSI-X is unsupported
instead of bailing out.
Fixes: 1c0c2163aa ("hw/block/nvme: verify msix_init_exclusive_bar() return value")
Fixes: fbf2e5375e ("hw/block/nvme: Verify msix_vector_use() returned value")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Added brief descriptions of the new device properties that are
now available to users to configure features of Zoned Namespace
Command Set in the emulator.
This patch is for documentation only, no functionality change.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Zone Descriptor Extension is a label that can be assigned to a zone.
It can be set to an Empty zone and it stays assigned until the zone
is reset.
This commit adds a new optional module property,
"zoned.descr_ext_size". Its value must be a multiple of 64 bytes.
If this value is non-zero, it becomes possible to assign extensions
of that size to any Empty zones. The default value for this property
is 0, therefore setting extensions is disabled by default.
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add two module properties, "zoned.max_active" and "zoned.max_open"
to control the maximum number of zones that can be active or open.
Once these variables are set to non-default values, these limits are
checked during I/O and Too Many Active or Too Many Open command status
is returned if they are exceeded.
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The emulation code has been changed to advertise NVM Command Set when
"zoned" device property is not set (default) and Zoned Namespace
Command Set otherwise.
Define values and structures that are needed to support Zoned
Namespace Command Set (NVMe TP 4053) in PCI NVMe controller emulator.
Define trace events where needed in newly introduced code.
In order to improve scalability, all open, closed and full zones
are organized in separate linked lists. Consequently, almost all
zone operations don't require scanning of the entire zone array
(which potentially can be quite large) - it is only necessary to
enumerate one or more zone lists.
Handlers for three new NVMe commands introduced in Zoned Namespace
Command Set specification are added, namely for Zone Management
Receive, Zone Management Send and Zone Append.
Device initialization code has been extended to create a proper
configuration for zoned operation using device properties.
Read/Write command handler is modified to only allow writes at the
write pointer if the namespace is zoned. For Zone Append command,
writes implicitly happen at the write pointer and the starting write
pointer value is returned as the result of the command. Write Zeroes
handler is modified to add zoned checks that are identical to those
done as a part of Write flow.
Subsequent commits in this series add ZDE support and checks for
active and open zone limits.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Ajay Joshi <ajay.joshi@wdc.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Matias Bjorling <matias.bjorling@wdc.com>
Signed-off-by: Aravind Ramesh <aravind.ramesh@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Define values and structures that are needed to support Zoned
Namespace Command Set (NVMe TP 4053).
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Many CNS commands have "allocated" command variants. These include
a namespace as long as it is allocated, that is a namespace is
included regardless if it is active (attached) or not.
While these commands are optional (they are mandatory for controllers
supporting the namespace attachment command), our QEMU implementation
is more complete by actually providing support for these CNS values.
However, since our QEMU model currently does not support the namespace
attachment command, these new allocated CNS commands will return the
same result as the active CNS command variants.
The reason for not hooking up this command completely is because the
NVMe specification requires the namespace management command to be
supported if the namespace attachment command is supported.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Define the structures and constants required to implement
Namespace Types support.
Namespace Types introduce a new command set, "I/O Command Sets",
that allows the host to retrieve the command sets associated with
a namespace. Introduce support for the command set and enable
detection for the NVM Command Set.
The new workflows for identify commands rely heavily on zero-filled
identify structs. E.g., certain CNS commands are defined to return
a zero-filled identify struct when an inactive namespace NSID
is supplied.
Add a helper function in order to avoid code duplication when
reporting zero-filled identify structures.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This log page becomes necessary to implement to allow checking for
Zone Append command support in Zoned Namespace Command Set.
This commit adds the code to report this log page for NVM Command
Set only. The parts that are specific to zoned operation will be
added later in the series.
All incoming admin and i/o commands are now only processed if their
corresponding support bits are set in this log. This provides an
easy way to control what commands to support and what not to
depending on set CC.CSS.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Move write processing to nvme_do_write() that now handles both WRITE
and WRITE ZEROES. Both nvme_write() and nvme_write_zeroes() become
inline helper functions.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The majority of code in nvme_rw() is becoming read- or write-specific.
Move these parts to two separate handlers, nvme_read() and nvme_write()
to make the code more readable and to remove multiple is_write checks
that has been present in the i/o path.
This is a refactoring patch, no change in functionality.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
In NVMe 1.4, a namespace must report an ID descriptor of UUID type
if it doesn't support EUI64 or NGUID. Add a new namespace property,
"uuid", that provides the user the option to either specify the UUID
explicitly or have a UUID generated automatically every time a
namespace is initialized.
Suggested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Controller reset ans subsystem shutdown are handled very much the same
in the current code, but some of the steps should be different in these
two cases.
Introduce two new functions, nvme_reset_ctrl() and nvme_shutdown_ctrl(),
to separate some portions of the code from nvme_clear_ctrl(). The steps
that are made different between reset and shutdown are that BAR.CC is not
reset to zero upon the shutdown and namespace data is flushed to
backing storage as a part of shutdown handling, but not upon reset.
Suggested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit 37712e00b1 ("hw/block/nvme: factor out pmr setup") changed the
control flow such that the CAP register is erronously cleared after
nvme_init_pmr() has configured it. Since the entire NvmeCtrl structure
is zero-filled initially, there is no need for the explicit clearing, so
just remove it.
Fixes: 37712e00b1 ("hw/block/nvme: factor out pmr setup")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Add the Compare command.
This implementation uses a bounce buffer to read in the data from
storage and then compare with the host supplied buffer.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: rebased]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for the Dataset Management command and the Deallocate
attribute. Deallocation results in discards being sent to the underlying
block device. Whether of not the blocks are actually deallocated is
affected by the same factors as Write Zeroes (see previous commit).
format | discard | dsm (512B) dsm (4KiB) dsm (64KiB)
--------------------------------------------------------
qcow2 ignore n n n
qcow2 unmap n n y
raw ignore n n n
raw unmap n y y
Again, a raw format and 4KiB LBAs are preferable.
In order to set the Namespace Preferred Deallocate Granularity and
Alignment fields (NPDG and NPDA), choose a sane minimum discard
granularity of 4KiB. If we are using a passthru device supporting
discard at a 512B granularity, user should set the discard_granularity
property explicitly. NPDG and NPDA will also account for the
cluster_size of the block driver if required (i.e. for QCOW2).
See NVM Express 1.3d, Section 6.7 ("Dataset Management command").
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
This adds the NPWG, NPWA, NPDG, NPDA and NOWS family of fields to the
shared nvme.h header for use by later patches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Fam Zheng <fam@euphon.net>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Add support for reporting the Deallocated or Unwritten Logical Block
Error (DULBE).
Rely on the block status flags reported by the block layer and consider
any block with the BDRV_BLOCK_ZERO flag to be deallocated.
Multiple factors affect when a Write Zeroes command result in
deallocation of blocks.
* the underlying file system block size
* the blockdev format
* the 'discard' and 'logical_block_size' parameters
format | discard | wz (512B) wz (4KiB) wz (64KiB)
-----------------------------------------------------
qcow2 ignore n n y
qcow2 unmap n n y
raw ignore n y y
raw unmap n y y
So, this works best with an image in raw format and 4KiB LBAs, since
holes can then be punched on a per-block basis (this assumes a file
system with a 4kb block size, YMMV). A qcow2 image, uses a cluster size
of 64KiB by default and blocks will only be marked deallocated if a full
cluster is zeroed or discarded. However, this *is* consistent with the
spec since Write Zeroes "should" deallocate the block if the Deallocate
attribute is set and "may" deallocate if the Deallocate attribute is not
set. Thus, we always try to deallocate (the BDRV_REQ_MAY_UNMAP flag is
always set).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add a new function, nvme_aio_err, to handle errors resulting from AIOs
and use this from the callbacks.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_check_bounds has no use of the NvmeCtrl parameter; remove it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
In the modules that we are checking so far, we can be stricter about the
difference between Optional[T] and T types. Enable that check.
Enabling it now will assist review on further typing and cleanup work.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-Id: <20210201193747.2169670-17-jsnow@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
