Implemented lpi processing at redistributor to get lpi config info
from lpi configuration table,determine priority,set pending state in
lpi pending table and forward the lpi to cpuif.Added logic to invoke
redistributor lpi processing with translated LPI which set/clear LPI
from ITS device as part of ITS INT,CLEAR,DISCARD command and
GITS_TRANSLATER processing.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-7-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added properties to enable ITS feature and define qemu system
address space memory in gicv3 common,setup distributor and
redistributor registers to indicate LPI support.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-6-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added ITS command queue handling for MAPTI,MAPI commands,handled ITS
translation which triggers an LPI via INT command as well as write
to GITS_TRANSLATER register,defined enum to differentiate between ITS
command interrupt trigger and GITS_TRANSLATER based interrupt trigger.
Each of these commands make use of other functionalities implemented to
get device table entry,collection table entry or interrupt translation
table entry required for their processing.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210910143951.92242-5-shashi.mallela@linaro.org
[PMM: use INTERRUPT for ItsCmdType enum name to avoid
conflict with INT type defined by Windows headers]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added functionality to trigger ITS command queue processing on
write to CWRITE register and process each command queue entry to
identify the command type and handle commands like MAPD,MAPC,SYNC.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-4-shashi.mallela@linaro.org
[PMM: fixed format string nit]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Defined descriptors for ITS device table,collection table and ITS
command queue entities.Implemented register read/write functions,
extract ITS table parameters and command queue parameters,extended
gicv3 common to capture qemu address space(which host the ITS table
platform memories required for subsequent ITS processing) and
initialize the same in ITS device.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-3-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added register definitions relevant to ITS,implemented overall
ITS device framework with stubs for ITS control and translater
regions read/write,extended ITS common to handle mmio init between
existing kvm device and newer qemu device.
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Message-id: 20210910143951.92242-2-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We've got SW that expects FSBL (Bootlooader) to setup clocks and
resets. It's quite common that users run that SW on QEMU without
FSBL (FSBL typically requires the Xilinx tools installed). That's
fine, since users can stil use -device loader to enable clocks etc.
To help folks understand what's going, a log (guest-error) message
would be helpful here. In particular with the serial port since
things will go very quiet if they get things wrong.
Suggested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-7-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Read or write to uart registers when unclocked or in reset should be
ignored. Add the check there, and as a result of this, the check in
uart_write_tx_fifo() is now unnecessary.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-6-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This converts uart_read() and uart_write() to memop_with_attrs() ops.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-5-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently the clock/reset check is done in uart_receive(), but we
can move the check to uart_can_receive() which is earlier.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210901124521.30599-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At present when input clock is disabled, any character transmitted
to tx fifo can still show on the serial line, which is wrong.
Fixes: b636db306e ("hw/char/cadence_uart: add clock support")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210901124521.30599-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of today, when booting upstream U-Boot for Xilinx Zynq, the UART
does not receive anything. Debugging shows that the UART input clock
frequency is zero which prevents the UART from receiving anything as
per the logic in uart_receive().
From zynq_slcr_reset_exit() comment, it intends to compute output
clocks according to ps_clk and registers. zynq_slcr_compute_clocks()
is called to accomplish the task, inside which device_is_in_reset()
is called to actually make the attempt in vain.
Rework reset_hold() and reset_exit() so that in the reset exit phase,
the logic can really compute output clocks in reset_exit().
With this change, upstream U-Boot boots properly again with:
$ qemu-system-arm -M xilinx-zynq-a9 -m 1G -display none -serial null -serial stdio \
-device loader,file=u-boot-dtb.bin,addr=0x4000000,cpu-num=0
Fixes: 38867cb7ec ("hw/misc/zynq_slcr: add clock generation for uarts")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210901124521.30599-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A PS/2 keyboard has a separate command reply queue that is
independent of the key queue. This prevents that command replies
and keyboard input mix. Keyboard command replies take precedence
over queued keystrokes. A new keyboard command removes any
remaining command replies from the command reply queue.
Implement a separate keyboard command reply queue and clear the
command reply queue before command execution. This brings the
PS/2 keyboard emulation much closer to a real PS/2 keyboard.
The command reply queue is located in a few free bytes directly
in front of the scancode queue. Because the scancode queue has
a maximum length of 16 bytes there are 240 bytes available for
the command reply queue. At the moment only a maximum of 3 bytes
are required. For compatibility reasons rptr, wptr and count kept
their function. rptr is the start, wptr is the end and count is
the length of the entire keyboard queue. The new variable cwptr
is the end of the command reply queue or -1 if the queue is
empty. To write to the command reply queue, rptr is moved
backward by the number of required bytes and the command replies
are written to the buffer starting at the new rptr position.
After writing, cwptr is at the old rptr position. Copying cwptr
to rptr clears the command reply queue. The command reply queue
can't overflow because each new keyboard command clears the
command reply queue.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/501
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/502
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210810133258.8231-2-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Extend the used ps2 buffer size to the available buffer size but
keep the maximum ps2 queue size.
The next patch needs a few bytes of the larger buffer size.
Signed-off-by: Volker Rümelin <vr_qemu@t-online.de>
Message-Id: <20210810133258.8231-1-vr_qemu@t-online.de>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
These will soon be required to enable nubus devices to support interrupts.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Now that q800 VIA1 and VIA2 are completely separate devices there is no need to
add a specific device prefix to ensure that the IRQ lines remain separate.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210830102447.10806-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Remove the mac_via device and wire up both q800 VIA1 and VIA2 directly for the
m68k q800 machine.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
After this change mac_via_reset() is now empty and can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210830102447.10806-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
These variables are already present in MOS6522Q800VIA1State and so it is just
the VMStateDescription move that is needed.
With this change the mac_via VMStateDescription is now empty and can be removed
completely.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The ADB is accessed using clock and data pins on q800 VIA1 port B and so can be
moved to MOS6522Q800VIA1State.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210830102447.10806-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The PRAM/RTC is accessed using clock and data pins on q800 VIA1 port B and so
can be moved to MOS6522Q800VIA1State.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210830102447.10806-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The PRAM contents are accessed using clock and data pins on q800 VIA1 port B
and so can be moved to MOS6522Q800VIA1State.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This variable is already present in MOS6522Q800VIA1State and can be moved
immediately into the q800 VIA1 VMStateDescription.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Move the parent mos6522 objects from vmstate_mac_via into the new VMStateDescription
structures to begin the process of splitting MacVIAState into separate VIA1 and
VIA2 devices.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210830102447.10806-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
After an SDLC "Enter hunt" command has been sent the STATUS_SYNC bit should remain
high until the flag byte has been detected. Whilst the ESCC device doesn't yet
implement SDLC mode, without this change the active low STATUS_SYNC is constantly
asserted causing the MacOS OpenTransport extension to hang on startup as it thinks
it is constantly receiving LocalTalk responses during its initial negotiation
phase.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This removes duplication of the internal device state initialisation between
device reset and soft reset.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that register values at reset are handled elsewhere for all of device reset,
soft reset and hard reset, escc_reset_chn() only needs to handle initialisation
of internal device state.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The hardware reset differs from a device reset in that it only changes the contents
of specific registers. Remove the code that resets all the registers to zero during
hardware reset and implement the default values using the existing soft reset code
with the additional changes listed in the table in the "Z85C30 Reset" section.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The software reset differs from a device reset in that it only changes the contents
of specific registers. Remove the code that resets all the registers to zero during
soft reset and implement the default values listed in the table in the "Z85C30 Reset"
section.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This new hardware reset function is to be called for both channels when the
hardware reset bit is written to register WR9. Its initial implementation is
the same as the existing escc_reset_chn() function used for device reset.
Add a new trace event when the guest initiates a hard reset via the WR9 register
to help diagnose guest reset issues.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This new software reset function is to be called when the appropriate channel
software reset bit is written to register WR9. Its initial implementation is
the same as the existing escc_reset_chn() function used for device reset.
Add a new trace event when the guest initiates a soft reset via the WR9 register
to help diagnose guest reset issues.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This is to ensure that a device reset always returns the ESCC to a known state.
Note that this is currently redundant with the same code in escc_reset_chn()
but that will change shortly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Also fix a couple of spelling mistakes in comments.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210903113223.19551-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Commit 24f675cd3b ("sparc/sun4m: Use start-powered-off CPUState property") changed
the sun4m CPU reset code to use the start-powered-off property and so split the
creation of the CPU into separate instantiation and realization phases to enable
the new start-powered-off property to be set.
This accidentally broke sun4m machines with more than one CPU present since
sparc_cpu_realizefn() sets a default CPU id, and now that realization occurs after
calling cpu_sparc_set_id() in cpu_devinit() the CPU id gets reset back to the
default instead of being uniquely encoded based upon the CPU number. As soon as
another CPU is brought online, the OS gets confused between them and promptly
panics.
Resolve the issue by moving the cpu_sparc_set_id() call in cpu_devinit() to after
the point where the CPU device has been realized as before.
Fixes: 24f675cd3b ("sparc/sun4m: Use start-powered-off CPUState property")
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210825095100.20180-1-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Add the new gen16 features to the default model and fence them for
machine version 6.1 and earlier.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210907101017.27126-1-borntraeger@de.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The PAGE_SIZE macro is causing trouble on Alpine Linux since it
clashes with a macro from a system header there. We already have
the TARGET_PAGE_SIZE, TARGET_PAGE_MASK and TARGET_PAGE_BITS macros
in QEMU anyway, so let's simply replace the PAGE_SIZE, PAGE_MASK
and PAGE_SHIFT macro with their TARGET_* counterparts.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/572
Message-Id: <20210901125800.611183-1-thuth@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Eric Farman <farman@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Let's enable storage keys lazily under TCG, just as we do under KVM.
Only fairly old Linux versions actually make use of storage keys, so it
can be kind of wasteful to allocate quite some memory and track
changes and references if nobody cares.
We have to make sure to flush the TLB when enabling storage keys after
the VM was already running: otherwise it might happen that we don't
catch references or modifications afterwards.
Add proper documentation to all callbacks.
The kvm-unit-tests skey tests keeps on working with this change.
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210903155514.44772-14-david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
... and make it return a bool instead.
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210903155514.44772-13-david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Let's validate the given address and report a proper error in case it's
not. All call paths now properly check the validity of the given GFN.
Remove the TODO.
The errors inside the getter and setter should only trigger if something
really goes wrong now, for example, with a broken migration stream. Or
when we forget to update the storage key allocation with memory hotplug.
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210903155514.44772-12-david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Handle it similar to migration. Assert that we're holding the BQL, to
make sure we don't see concurrent modifications.
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210903155514.44772-11-david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Let's use the guest_phys_blocks API to get physical memory regions
that are well defined inside our physical address space and migrate the
storage keys of these.
This is a preparation for having memory besides initial ram defined in
the guest physical address space, for example, via memory devices. We
get rid of the ms->ram_size dependency.
Please note that we will usually have very little (--> 1) physical
ranges. With virtio-mem might have significantly more ranges in the
future. If that turns out to be a problem (e.g., total memory
footprint of the list), we could look into a memory mapping
API that avoids creation of a list and instead triggers a callback for
each range.
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210903155514.44772-10-david@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
hsch and csch basically have two parts: execute the command,
and perform the halt/clear function. For fully emulated
subchannels, it is pretty clear how it will work: check the
subchannel state, and actually 'perform the halt/clear function'
and set cc 0 if everything looks good.
For passthrough subchannels, some of the checking is done
within QEMU, but some has to be done within the kernel. QEMU's
subchannel state may be such that we can perform the async
function, but the kernel may still get a cc != 0 when it is
actually executing the instruction. In that case, we need to
set the condition actually encountered by the kernel; if we
set cc 0 on error, we would actually need to inject an interrupt
as well.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Tested-by: Jared Rossi <jrossi@linux.ibm.com>
Message-Id: <20210705163952.736020-2-cohuck@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch switches to initialize dev.nvqs from the VhostNetOptions
instead of assuming it was 2. This is useful for implementing control
virtqueue support which will be a single vhost_net structure with a
single cvq.
Note that nvqs is still set to 2 for all users and this patch does not
change functionality.
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210903091031.47303-6-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The nvqs and vqs have been initialized during vhost_net_init() and are
not expected to change during the life cycle of vhost_net
structure. So this patch removes the meaningless assignment.
Reviewed-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210903091031.47303-4-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We should return error code instead of zero, otherwise there's no way
for the caller to detect the failure.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210903091031.47303-3-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Shashi Mallela
Chris Rauer
Bin Meng
Peter Maydell
Volker Rümelin
Mark Cave-Ayland
Christian Borntraeger
Thomas Huth
David Hildenbrand
Cornelia Huck
Jason Wang