Give each CPU its own container memory region. This is necessary
for two reasons:
* some devices are instantiated one per CPU and the CPU sees only
its own device
* since a memory region can only be put into one container, we must
give each armv7m object a different MemoryRegion as its 'memory'
property, or a dual-CPU configuration will assert on realize when
the second armv7m object tries to put the MR into a container when
it is already in the first armv7m object's container
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-13-peter.maydell@linaro.org
The SSE-200 has two Cortex-M33 CPUs. These see the same view
of memory, with the exception of the "private CPU region" which
has per-CPU devices. Internal device interrupts for SSE-200
devices are mostly wired up to both CPUs, with the exception of
a few per-CPU devices. External GPIO inputs on the SSE-200
device are provided for the second CPU's interrupts above 32,
as is already the case for the first CPU.
Refactor the code to support creation of multiple CPUs.
For the moment we leave all CPUs with the same view of
memory: this will not work in the multiple-CPU case, but
we will fix this in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-12-peter.maydell@linaro.org
For the IoTKit the SRAM bank size is always 32K (15 bits); for the
SSE-200 this is a configurable parameter, which defaults to 32K but
can be changed when it is built into a particular SoC. For instance
the Musca-B1 board sets it to 128K (17 bits).
Make the bank size a QOM property. We follow the SSE-200 hardware in
naming the parameter SRAM_ADDR_WIDTH, which specifies the number of
address bits of a single SRAM bank.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-11-peter.maydell@linaro.org
The SSE-200 has four banks of SRAM, each with its own
Memory Protection Controller, where the IoTKit has only one.
Make the number of SRAM banks a field in ARMSSEInfo.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-10-peter.maydell@linaro.org
The SSE-200 has 4 banks of SRAM, each with its own internal
Memory Protection Controller. The interrupt status for these
extra MPCs appears in the same security controller SECMPCINTSTATUS
register as the MPC for the IoTKit's single SRAM bank. Enhance the
iotkit-secctl device to allow 4 MPCs. (If the particular IoTKit/SSE
variant in use does not have all 4 MPCs then the unused inputs will
simply result in the SECMPCINTSTATUS bits being zero as required.)
The hardcoded constant "1"s in armsse.c indicate the actual number
of SRAM MPCs the IoTKit has, and will be replaced in the following
commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-9-peter.maydell@linaro.org
Rename the files that used to be iotkit.[ch] to
armsse.[ch] to reflect the fact they new cover
multiple Arm subsystems for embedded.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-8-peter.maydell@linaro.org
Rename various internal uses of 'iotkit' in hw/arm/iotkit.c to
'armsse', for consistency. The remaining occurences are:
* related to the devices TYPE_IOTKIT_SYSCTL, TYPE_IOTKIT_SYSINFO,
etc, which this refactor is not touching
* references that apply specifically to the IoTKit (like
the lack of a private CPU region)
* the vmstate, which keeps its old "iotkit" name for
migration compatibility reasons
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-7-peter.maydell@linaro.org
The Arm SSE-200 Subsystem for Embedded is a revised and
extended version of the older IoTKit SoC. Prepare for
adding a model of it by refactoring the IoTKit code into
an abstract base class which contains the functionality,
driven by a class data block specific to each subclass.
(This is the same approach used by the existing bcm283x
SoC family implementation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-6-peter.maydell@linaro.org
The Arm IoTKit was effectively the forerunner of a series of
subsystems for embedded SoCs, named the SSE-050, SSE-100 and SSE-200:
https://developer.arm.com/products/system-design/subsystems
These are generally quite similar, though later iterations have
extra devices that earlier ones do not.
We want to add a model of the SSE-200, which means refactoring the
IoTKit code into an abstract base class and subclasses (using the
same design that the bcm283x SoC and Aspeed SoC family
implementations do). As a first step, rename the IoTKit struct and
QOM macros to ARMSSE, which is what we're going to name the base
class. We temporarily retain TYPE_IOTKIT to avoid changing the
code that instantiates a TYPE_IOTKIT device here and then changing
it back again when it is re-introduced as a subclass.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-5-peter.maydell@linaro.org
Expose "start-powered-off" as a property of the ARMv7M container,
which we just pass through to the CPU object in the same way that we
do for "init-svtor" and "idau". (We want this for the SSE-200, which
powers up only the first CPU at reset and leaves the second powered
down.)
As with the other CPU properties here, we can't just use alias
properties, because the CPU QOM object is not created until armv7m
realize time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-4-peter.maydell@linaro.org
Rather than just creating the CPUs with object_new, make them child
objects of the armv7m container. This will allow the cluster code to
find the CPUs if an armv7m object is made a child of a cluster object.
object_new_with_props() will do the parenting for us.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-3-peter.maydell@linaro.org
Currently the ARMv7M NVIC object's realize method assumes that the
CPU the NVIC is attached to is CPU 0, because it thinks there can
only ever be one CPU in the system. To allow a dual-Cortex-M33
setup we need to remove this assumption; instead the armv7m
wrapper object tells the NVIC its CPU, in the same way that it
already tells the CPU what the NVIC is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-2-peter.maydell@linaro.org
set object owner in memory_region_init_ram() instead
of NULL.
Signed-off-by: kumar sourav <sourav.jb1988@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190125155630.17430-1-sourav.jb1988@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- New debugging QMP command to explore block graphs
- Converted DPRINTF()s to trace events
- Fixed qemu-io's use of getopt() for systems with optreset
- Minor NVMe emulation fixes
- An iotest fix
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcUkaiAAoJEPQH2wBh1c9AHsEIAIU0+FNjtdz7lNgyeBCSFCFa
/qWNk4+w6QBfhTTx/N0hGwh5/FvNYQhby8VHtZitE4/QcLbJwHYgWf14pwce3tP3
3qNB87AdQpKMpbajQM2x2Xy8lnlPeM7fe21Q/12vuX7AlEDT3gH+W9rg94bw2oFN
r+xBk6H5F2aVElw3CwMM7eary4+dPnnCQwAnoqM+g5hdpL+0scrIyARGw7v0hmSn
LDWESCM4a55lEYmwj1wS3J3uj6Fj00yzBvcEuCcT1GO+lXlV8/ciO9r2HqxVKwgz
4GAi/BERoMKjfn+/77/yI5flprPx2voNGgkyBY4C3z9ncnN6u02QBZSusBIWpSg=
=Kt4r
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/xanclic/tags/pull-block-2019-01-31' into staging
Block patches:
- New debugging QMP command to explore block graphs
- Converted DPRINTF()s to trace events
- Fixed qemu-io's use of getopt() for systems with optreset
- Minor NVMe emulation fixes
- An iotest fix
# gpg: Signature made Thu 31 Jan 2019 00:51:46 GMT
# gpg: using RSA key F407DB0061D5CF40
# gpg: Good signature from "Max Reitz <mreitz@redhat.com>" [full]
# Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40
* remotes/xanclic/tags/pull-block-2019-01-31:
iotests: Allow 147 to be run concurrently
iotests: Bind qemu-nbd to localhost in 147
iotests.py: Add qemu_nbd_pipe()
nvme: use pci_dev directly in nvme_realize
nvme: ensure the num_queues is not zero
nvme: use TYPE_NVME instead of constant string
qemu-io: Add generic function for reinitializing optind.
block/sheepdog: Convert from DPRINTF() macro to trace events
block/file-posix: Convert from DPRINTF() macro to trace events
block/curl: Convert from DPRINTF() macro to trace events
block/ssh: Convert from DPRINTF() macro to trace events
scripts: add render_block_graph function for QEMUMachine
qapi: add x-debug-query-block-graph
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- code clean-up
- LGPL information clean-up
- fix typo (acpi)
-----BEGIN PGP SIGNATURE-----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=1OOM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-pull-request' into staging
- add device category (edu, i8042, sd memory card)
- code clean-up
- LGPL information clean-up
- fix typo (acpi)
# gpg: Signature made Wed 30 Jan 2019 13:21:50 GMT
# gpg: using RSA key F30C38BD3F2FBE3C
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-pull-request:
virtio-blk: remove duplicate definition of VirtIOBlock *s pointer
hw/block: clean up stale xen_disk trace entries
target/m68k: Fix LGPL information in the file headers
target/s390x: Fix LGPL version in the file header comments
tcg: Fix LGPL version number
target/tricore: Fix LGPL version number
target/openrisc: Fix LGPL version number
COPYING.LIB: Synchronize the LGPL 2.1 with the version from gnu.org
Don't talk about the LGPL if the file is licensed under the GPL
hw: sd: set category of the sd memory card
hw: input: set category of the i8042 device
typo: apci->acpi
hw: edu: set category of the edu device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
User-visible changes:
* The new qemu-trace-stap script makes it convenient to collect traces without
writing SystemTap scripts. See "man qemu-trace-stap" for details.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcURdlAAoJEJykq7OBq3PIPqAH/iSkYDDeWLQy4eqeTPpbsxd4
U6mUYC/m2g1bevj1TxdFmr2g5LReGTd4w35w6/SUaLMHsu701T7gK+0z1gP2/N/D
qzJiM9xxF6xYq1P4hWJGf+XsbJ0OVf7oRwn1j8qXVBxjIxERX98z0ZUtbk/aulGi
wnNXycBufpKGk2PkQC+pBfhU2775dMqpUV49z9mqyVzsiZQlzbx8WMDQj1Ic1fbe
ZcAvX5D350HJjB3Z+9wJ1V2pC9Gu+z3TIup+YR1Bkch0ywyTCVTqcepoOXwzQamm
84bifPdObBm7SbbwtrwoVKYLrdIrbb3PTWaOlWVUKruKIIf8hzn5BxC3wChb2Qk=
=bex6
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
Pull request
User-visible changes:
* The new qemu-trace-stap script makes it convenient to collect traces without
writing SystemTap scripts. See "man qemu-trace-stap" for details.
# gpg: Signature made Wed 30 Jan 2019 03:17:57 GMT
# gpg: using RSA key 9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>" [full]
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>" [full]
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request:
trace: rerun tracetool after ./configure changes
trace: improve runstate tracing
trace: add ability to do simple printf logging via systemtap
trace: forbid use of %m in trace event format strings
trace: enforce that every trace-events file has a final newline
display: ensure qxl log_buf is a nul terminated string
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To do this, we need to allow creating the NBD server on various ports
instead of a single one (which may not even work if you run just one
instance, because something entirely else might be using that port).
So we just pick a random port in [32768, 32768 + 1024) and try to create
a server there. If that fails, we just retry until something sticks.
For the IPv6 test, we need a different range, though (just above that
one). This is because "localhost" resolves to both 127.0.0.1 and ::1.
This means that if you bind to it, it will bind to both, if possible, or
just one if the other is already in use. Therefore, if the IPv6 test
has already taken [::1]:some_port and we then try to take
localhost:some_port, that will work -- only the second server will be
bound to 127.0.0.1:some_port alone and not [::1]:some_port in addition.
So we have two different servers on the same port, one for IPv4 and one
for IPv6.
But when we then try to connect to the server through
localhost:some_port, we will always end up at the IPv6 one (as long as
it is up), and this may not be the one we want.
Thus, we must make sure not to create an IPv6-only NBD server on the
same port as a normal "dual-stack" NBD server -- which is done by using
distinct port ranges, as explained above.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20181221234750.23577-4-mreitz@redhat.com
Reviewed-by: John Snow <jsnow@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
By default, qemu-nbd binds to 0.0.0.0. However, we then proceed to
connect to "localhost". Usually, this works out fine; but if this test
is run concurrently, some other test function may have bound a different
server to ::1 (on the same port -- you can bind different serves to the
same port, as long as one is on IPv4 and the other on IPv6).
So running qemu-nbd works, it can bind to 0.0.0.0:NBD_PORT. But
potentially a concurrent test has successfully taken [::1]:NBD_PORT. In
this case, trying to connect to "localhost" will lead us to the IPv6
instance, where we do not want to end up.
Fix this by just binding to "localhost". This will make qemu-nbd error
out immediately and not give us cryptic errors later.
(Also, it will allow us to just try a different port as of a future
patch.)
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20181221234750.23577-3-mreitz@redhat.com
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
In some cases, we may want to deal with qemu-nbd errors (e.g. by
launching it in a different configuration until it no longer throws
any). In that case, we do not want its output ending up in the test
output.
It may still be useful for handling the error, though, so add a new
function that works basically like qemu_nbd(), only that it returns the
qemu-nbd output instead of making it end up in the log. In contrast to
qemu_img_pipe(), it does still return the exit code as well, though,
because that is even more important for error handling.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-id: 20181221234750.23577-2-mreitz@redhat.com
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
There is no need to make another reference.
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190120055558.32984-4-liq3ea@163.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
When it is zero, it causes segv.
Using following command:
"-drive file=//home/test/test1.img,if=none,id=id0
-device nvme,drive=id0,serial=test,num_queues=0"
causes following Backtrack:
Thread 4 "qemu-system-x86" received signal SIGSEGV, Segmentation fault.
[Switching to Thread 0x7fffe9735700 (LWP 30952)]
0x0000555555a7a77c in nvme_start_ctrl (n=0x5555577473f0) at hw/block/nvme.c:825
825 if (unlikely(n->cq[0])) {
(gdb) bt
0 0x0000555555a7a77c in nvme_start_ctrl (n=0x5555577473f0)
at hw/block/nvme.c:825
1 0x0000555555a7af7f in nvme_write_bar (n=0x5555577473f0, offset=20,
data=4587521, size=4) at hw/block/nvme.c:969
2 0x0000555555a7b81a in nvme_mmio_write (opaque=0x5555577473f0, addr=20,
data=4587521, size=4) at hw/block/nvme.c:1163
3 0x0000555555869236 in memory_region_write_accessor (mr=0x555557747cd0,
addr=20, value=0x7fffe97320f8, size=4, shift=0, mask=4294967295, attrs=...)
at /home/test/qemu1/qemu/memory.c:502
4 0x0000555555869446 in access_with_adjusted_size (addr=20,
value=0x7fffe97320f8, size=4, access_size_min=2, access_size_max=8,
access_fn=0x55555586914d <memory_region_write_accessor>,
mr=0x555557747cd0, attrs=...) at /home/test/qemu1/qemu/memory.c:568
5 0x000055555586c479 in memory_region_dispatch_write (mr=0x555557747cd0,
addr=20, data=4587521, size=4, attrs=...)
at /home/test/qemu1/qemu/memory.c:1499
6 0x00005555558030af in flatview_write_continue (fv=0x7fffe0061130,
addr=4273930260, attrs=..., buf=0x7ffff7ff0028 "\001", len=4, addr1=20,
l=4, mr=0x555557747cd0) at /home/test/qemu1/qemu/exec.c:3234
7 0x00005555558031f9 in flatview_write (fv=0x7fffe0061130, addr=4273930260,
attrs=..., buf=0x7ffff7ff0028 "\001", len=4)
at /home/test/qemu1/qemu/exec.c:3273
8 0x00005555558034ff in address_space_write (
---Type <return> to continue, or q <return> to quit---
as=0x555556758480 <address_space_memory>, addr=4273930260, attrs=...,
buf=0x7ffff7ff0028 "\001", len=4) at /home/test/qemu1/qemu/exec.c:3363
9 0x0000555555803550 in address_space_rw (
as=0x555556758480 <address_space_memory>, addr=4273930260, attrs=...,
buf=0x7ffff7ff0028 "\001", len=4, is_write=true)
at /home/test/qemu1/qemu/exec.c:3374
10 0x00005555558884a1 in kvm_cpu_exec (cpu=0x555556920e40)
at /home/test/qemu1/qemu/accel/kvm/kvm-all.c:2031
11 0x000055555584cd9d in qemu_kvm_cpu_thread_fn (arg=0x555556920e40)
at /home/test/qemu1/qemu/cpus.c:1281
12 0x0000555555dbaf6d in qemu_thread_start (args=0x5555569438a0)
at util/qemu-thread-posix.c:502
13 0x00007ffff5dc86db in start_thread (arg=0x7fffe9735700)
at pthread_create.c:463
14 0x00007ffff5af188f in clone ()
at ../sysdeps/unix/sysv/linux/x86_64/clone.S:95
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190120055558.32984-3-liq3ea@163.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Li Qiang <liq3ea@163.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190120055558.32984-2-liq3ea@163.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
On FreeBSD 11.2:
$ nbdkit memory size=1M --run './qemu-io -f raw -c "aio_write 0 512" $nbd'
Parsing error: non-numeric argument, or extraneous/unrecognized suffix -- aio_write
After main option parsing, we reinitialize optind so we can parse each
command. However reinitializing optind to 0 does not work on FreeBSD.
What happens when you do this is optind remains 0 after the option
parsing loop, and the result is we try to parse argv[optind] ==
argv[0] == "aio_write" as if it was the first parameter.
The FreeBSD manual page says:
In order to use getopt() to evaluate multiple sets of arguments, or to
evaluate a single set of arguments multiple times, the variable optreset
must be set to 1 before the second and each additional set of calls to
getopt(), and the variable optind must be reinitialized.
(From the rest of the man page it is clear that optind must be
reinitialized to 1).
The glibc man page says:
A program that scans multiple argument vectors, or rescans the same
vector more than once, and wants to make use of GNU extensions such as
'+' and '-' at the start of optstring, or changes the value of
POSIXLY_CORRECT between scans, must reinitialize getopt() by resetting
optind to 0, rather than the traditional value of 1. (Resetting to 0
forces the invocation of an internal initialization routine that
rechecks POSIXLY_CORRECT and checks for GNU extensions in optstring.)
This commit introduces an OS-portability function called
qemu_reset_optind which provides a way of resetting optind that works
on FreeBSD and platforms that use optreset, while keeping it the same
as now on other platforms.
Note that the qemu codebase sets optind in many other places, but in
those other places it's setting a local variable and not using getopt.
This change is only needed in places where we are using getopt and the
associated global variable optind.
Signed-off-by: Richard W.M. Jones <rjones@redhat.com>
Message-id: 20190118101114.11759-2-rjones@redhat.com
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181213162727.17438-5-lvivier@redhat.com
[mreitz: Fixed sheepdog_snapshot_create_inode's format string to use
PRIx32 for uint32_ts]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181213162727.17438-3-lvivier@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20181213162727.17438-2-lvivier@redhat.com
[mreitz: Fixed type of ssh_{read,write}_return's parameter to be ssize_t
instead of size_t]
Signed-off-by: Max Reitz <mreitz@redhat.com>
Render block nodes graph with help of graphviz. This new function is
for debugging, so there is no sense to put it into qemu.py as a method
of QEMUMachine. Let's instead put it separately.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 20181221170909.25584-3-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
Add a new command, returning block nodes (and their users) graph.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-id: 20181221170909.25584-2-vsementsov@virtuozzo.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
VirtIOBlock *s is already defined and initialized with req->dev
on top of virtio_blk_handle_request(), so we can remove it from
the code block of VIRTIO_BLK_T_GET_ID case.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190130095231.42081-1-sgarzare@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
This should have been removed then xen_disk.c was removed but I missed them.
Fixes: 19f87870ba
xen: remove the legacy 'xen_disk' backend
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190122145132.12571-1-paul.durrant@citrix.com>
[lv: s/stake/stale/ and add "Fixes" tag]
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It's either "GNU *Library* General Public License version 2" or
"GNU Lesser General Public License version *2.1*", but there was
no "version 2.0" of the "Lesser" license. So assume that version
2.1 is meant here.
Also some files mention the GPL instead of the LGPL after declaring
that the files are licensed under the LGPL, so change these spots to
use LGPL, too.
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1548769438-28942-1-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It's either "GNU *Library* General Public License version 2" or
"GNU Lesser General Public License version *2.1*", but there was
no "version 2.0" of the "Lesser" license. So assume that version
2.1 is meant here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <1548769067-20792-1-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It's either "GNU *Library* General Public version 2" or "GNU Lesser
General Public version *2.1*", but there was no "version 2.0" of the
"Lesser" library. So assume that version 2.1 is meant here.
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <1548252536-6242-5-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It's either "GNU *Library* General Public version 2" or "GNU Lesser
General Public version *2.1*", but there was no "version 2.0" of the
"Lesser" library. So assume that version 2.1 is meant here.
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <1548252536-6242-4-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
It's either "GNU *Library* General Public version 2" or "GNU Lesser
General Public version *2.1*", but there was no "version 2.0" of the
"Lesser" library. So assume that version 2.1 is meant here.
Cc: Stafford Horne <shorne@gmail.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Acked-by: Stafford Horne <shorne@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <1548252536-6242-3-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The current version of the LGPL 2.1 from gnu.org (see the URL
https://www.gnu.org/licenses/old-licenses/lgpl-2.1.txt ) slightly
differs from the old one that we use in our repository. Especially
the recommendation to use "either version 2 of the License, or [...]
any later version" is somewhat misleading, since there was never a
"version 2" of the "Lesser GPL" license - the "version 2" was still
called "Library GPL" instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <1548252536-6242-2-git-send-email-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Some files claim that the code is licensed under the GPL, but then
suddenly suggest that the user should have a look at the LGPL.
That's of course non-sense, replace it with the correct GPL wording
instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1548255083-8190-1-git-send-email-thuth@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Sets the category of the sd memory card as DEVICE_CATEGORY_STORAGE.
Devices should be assigned to one of DEVICE_CATEGORY_XXXX.
Signed-off-by: kumar sourav <sourav.jb1988@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190124162045.10474-1-sourav.jb1988@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Sets the category of i8042 device as DEVICE_CATEGORY_INPUT
Devices should be assigned to one of DEVICE_CATEGORY_XXXX.
Signed-off-by: kumar sourav <sourav.jb1988@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20190125151440.13794-1-sourav.jb1988@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
apci_1_compatible should be acpi_1_compatible.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190125094047.22276-1-dgilbert@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Sets the category of edu device as DEVICE_CATEGORY_MISC.
Devices should be assigned to one of DEVICE_CATEGORY_XXXX.
Signed-off-by: kumar sourav <sourav.jb1988@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20190124144606.4352-1-sourav.jb1988@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
qemu_write_full takes care of partial blocking writes,
as in cases of larger file sizes
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190129131908.27924-4-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
For every MTP_WRITE_BUF_SZ copied, this patch writes it to file before
getting the next block of data. The file is kept opened for the
duration of the operation but the sanity checks on the write operation
are performed only once when the write operation starts. Additionally,
we also update the file size in the object metadata once the file has
completely been written.
Suggested-by: Gerd Hoffman <kraxel@redhat.com>
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190129131908.27924-3-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This is a "pre-patch" to breaking up the write buffer for
MTP writes. Instead of allocating a mtp buffer equal to size
sent by the initiator, we start with a small size and reallocate
multiples (of that small size) as needed.
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-id: 20190129131908.27924-2-bsd@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Implement underrun/overrun events of isochronous endpoints
according to XHCI spec (4.10.3.1)
Guest software restarts data streaming when receives these events.
The XHCI reports these events using interrupter assigned
to the slot (as these events do not have TRB), so current
commit adds the field of assigned interrupter to the
XHCISlot structure. Guest software assigns interrupter to the
slot on 'Address Device' and 'Evaluate Context' commands.
Signed-off-by: Yuri Benditovich <yuri.benditovich@janustech.com>
Message-id: 20190128200444.5128-3-yuri.benditovich@janustech.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
According to the XHCI spec (4.10.2) the controller
never halts isochronous endpoints. This commit prevent
stop of isochronous streaming when sporadic errors
status received from backends.
Signed-off-by: Yuri Benditovich <yuri.benditovich@janustech.com>
Message-id: 20190128200444.5128-2-yuri.benditovich@janustech.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
It's either "GNU *Library* General Public version 2" or "GNU Lesser
General Public version *2.1*", but there was no "version 2.0" of the
"Lesser" library. So assume that version 2.1 is meant here.
Additionally, suggest that the user should have received a copy of
the LGPL, and not the GPL here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1548254454-7659-1-git-send-email-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
