On s390x, each pci device has its own iommu, which is only properly
setup in qemu once the mpcifc instruction used to register the
translation table has been intercepted. Therefore, for a pci device that
is not configured or has not been initialized, proper translation is
neither required nor possible. Moreover, we may not have a host bridge
device ready yet.
This was exposed by a recent vfio change that triggers iommu translation
during the initialization of the vfio pci device. Let's do an early exit
in that case.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We keep the device's sense data in a byte array (following the
architecture), but the ecws are an array of 32 bit values. If we
just blindly copy the values, the sense data will change from
de-facto BE data to de-facto cpu-endian data, which means we end
up doing an incorrect conversion on LE hosts.
Let's just explicitly convert to cpu-endianness while assembling
the irb.
Reported-by: Andy Lutomirski <luto@kernel.org>
Tested-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
KVM_PPC_ALLOCATE_HTAB ioctl can return -ENOMEM for KVM guests and QEMU
never handled this correctly. But this didn't cause any problems till
now as KVM_PPC_ALLOCATE_HTAB ioctl returned with smaller than requested
HTAB when enough contiguous memory wasn't available in the host.
After the proposed kernel change: https://patchwork.ozlabs.org/patch/530501/,
KVM_PPC_ALLOCATE_HTAB ioctl will not fallback to lower sized HTAB
allocation and will fail if requested HTAB size can't be met.
Check for such failures in QEMU and abort appropriately. This will
prevent guest kernel from hanging/freezing during early boot by doing
graceful exit when host is unable to allocate requested HTAB.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The !CONFIG_KVM implementation of kvmppc_reset_htab() returns -1
by default. Change this to return 0 so that we fall back to user space
HTAB allocation for emulated guests.
This fixes the make check failures for ppc64 emulated target.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The changes are:
1. supports recent binutils;
2. 64bit BARs behind PCI bridges supported;
3. Many fixes for USB keyboard support - keys, XHCI;
4. virtio-vga support.
This image was built with:
gcc version 4.8.3 20140911 (Red Hat 4.8.3-7) (GCC)
GNU ld version 2.23.2
The full changelog is:
> version: update to 20151103
> documentation: Add a clause about signing off
> qemu/js2x/client: Support binutils >= 2.25.1
> Fix special keys on USB
> Fix function keys on USB
> pci-scan: program 64-bit mem bar range in pci-bridge bar
> Allow to build SLOF on Little Endian host
> usb-xhci: add keyboard support
> usb-xhci: ready the link trb early
> usb-xhci: scan usb high speed ports
> usb-xhci: bulk improve event handling loop
> usb-xhci: return on allocation failure
> usb-xhci: add delay in shutdown path
> usb-xhci: event trbs does not need link trb
> usb-hid: refactor usb key reading
> takeover: Fix header includes
> board-js2x: Add missing file dma-function.fs
> vga: Add support for virtio-vga
> qemu-vga: Use MMIO BAR instead of legacy IO ports
> slof: Change call_c() function to a proper assembler function
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit aa4bb58752 (ppc: Add mmu_model defines for arch 2.03 and 2.07)
removed the mmu_model definition POWERPC_MMU_2_06a which is needed by
PR KVM. Reintroduce it and also add POWERPC_MMU_2_07a.
This fixes QEMU crash (qemu: fatal: Unknown MMU model) during booting
of PR KVM guest.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- Make Windows happy with vfio-pci devices exposed on conventional
PCI buses on q35 by hiding PCIe capability (Alex Williamson)
- Convert to g_new() where appropriate (Markus Armbruster)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qJ77
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/awilliam/tags/vfio-update-20151110.0' into staging
VFIO updates 2015-11-10
- Make Windows happy with vfio-pci devices exposed on conventional
PCI buses on q35 by hiding PCIe capability (Alex Williamson)
- Convert to g_new() where appropriate (Markus Armbruster)
# gpg: Signature made Tue 10 Nov 2015 19:46:41 GMT using RSA key ID 3BB08B22
# gpg: Good signature from "Alex Williamson <alex.williamson@redhat.com>"
# gpg: aka "Alex Williamson <alex@shazbot.org>"
# gpg: aka "Alex Williamson <alwillia@redhat.com>"
# gpg: aka "Alex Williamson <alex.l.williamson@gmail.com>"
* remotes/awilliam/tags/vfio-update-20151110.0:
vfio: Use g_new() & friends where that makes obvious sense
vfio/pci: Hide device PCIe capability on non-express buses for PCIe VMs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T). Same Coccinelle semantic patch as in commit b45c03f.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When we have a PCIe VM, such as Q35, guests start to care more about
valid configurations of devices relative to the VM view of the PCI
topology. Windows will error with a Code 10 for an assigned device if
a PCIe capability is found for a device on a conventional bus. We
also have the possibility of IOMMUs, like VT-d, where the where the
guest may be acutely aware of valid express capabilities on physical
hardware.
Some devices, like tg3 are adversely affected by this due to driver
dependencies on the PCIe capability. The only solution for such
devices is to attach them to an express capable bus in the VM.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tlQv
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/juanquintela/tags/migration/20151110' into staging
migration/next for 20151110
# gpg: Signature made Tue 10 Nov 2015 14:23:26 GMT using RSA key ID 5872D723
# gpg: Good signature from "Juan Quintela <quintela@redhat.com>"
# gpg: aka "Juan Quintela <quintela@trasno.org>"
* remotes/juanquintela/tags/migration/20151110: (57 commits)
migration: qemu_savevm_state_cleanup becomes mandatory operation
Inhibit ballooning during postcopy
Disable mlock around incoming postcopy
End of migration for postcopy
Postcopy: Mark nohugepage before discard
postcopy: Wire up loadvm_postcopy_handle_ commands
Start up a postcopy/listener thread ready for incoming page data
Postcopy; Handle userfault requests
Round up RAMBlock sizes to host page sizes
Host page!=target page: Cleanup bitmaps
Don't iterate on precopy-only devices during postcopy
Don't sync dirty bitmaps in postcopy
postcopy: Check order of received target pages
Postcopy: Use helpers to map pages during migration
postcopy_ram.c: place_page and helpers
Page request: Consume pages off the post-copy queue
Page request: Process incoming page request
Page request: Add MIG_RP_MSG_REQ_PAGES reverse command
Postcopy: End of iteration
Postcopy: Postcopy startup in migration thread
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
since commit
commit 94f5a43704
Author: Liang Li <liang.z.li@intel.com>
Date: Mon Nov 2 15:37:00 2015 +0800
migration: defer migration_end & blk_mig_cleanup
when actual .cleanup callbacks calling was removed from complete operations.
The patch fixes regression introduced by the commit above results in
100% reliable assert for virtio-scsi VM with iothreads enabled during
'virsh create-snapshot' operation:
assert(i != mr->ioeventfd_nb);
memory_region_del_eventfd
virtio_pci_set_host_notifier_internal
virtio_pci_set_host_notifier
virtio_scsi_dataplane_start
virtio_scsi_handle_cmd
virtio_queue_notify_vq
virtio_queue_host_notifier_read
aio_dispatch
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Liang Li <liang.z.li@intel.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Juan Quintela <quintela@redhat.com>
CC: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Postcopy detects accesses to pages that haven't been transferred yet
using userfaultfd, and it causes exceptions on pages that are 'not
present'.
Ballooning also causes pages to be marked as 'not present' when the
guest inflates the balloon.
Potentially a balloon could be inflated to discard pages that are
currently inflight during postcopy and that may be arriving at about
the same time.
To avoid this confusion, disable ballooning during postcopy.
When disabled we drop balloon requests from the guest. Since ballooning
is generally initiated by the host, the management system should avoid
initiating any balloon instructions to the guest during migration,
although it's not possible to know how long it would take a guest to
process a request made prior to the start of migration.
Guest initiated ballooning will not know if it's really freed a page
of host memory or not.
Queueing the requests until after migration would be nice, but is
non-trivial, since the set of inflate/deflate requests have to
be compared with the state of the page to know what the final
outcome is allowed to be.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Userfault doesn't work with mlock; mlock is designed to nail down pages
so they don't move, userfault is designed to tell you when they're not
there.
munlock the pages we userfault protect before postcopy.
mlock everything again at the end if mlock is enabled.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Tweak the end of migration cleanup; we don't want to close stuff down
at the end of the main stream, since the postcopy is still sending pages
on the other thread.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Prior to servicing userfault requests we must ensure we've not got
huge pages in the area that might include non-transferred memory,
since a hugepage could incorrectly mark the whole huge page as present.
We mark the area as non-huge page (nhp) just before we perform
discards; the discard code now tells us to discard any areas
that haven't been sent (as well as any that are redirtied);
any already formed transparent-huge-pages get fragmented
by this discard process if they cotnain any discards.
Transparent huge pages that have been entirely transferred
and don't contain any discards are not broken by this mechanism;
they stay as huge pages.
By starting postcopy after a full precopy pass, many of the pages
then stay as huge pages; this is important for maintaining performance
after the end of the migration.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Wire up more of the handlers for the commands on the destination side,
in particular loadvm_postcopy_handle_run now has enough to start the
guest running.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The loading of a device state (during postcopy) may access guest
memory that's still on the source machine and thus might need
a page fill; split off a separate thread that handles the incoming
page data so that the original incoming migration code can finish
off the device data.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
userfaultfd is a Linux syscall that gives an fd that receives a stream
of notifications of accesses to pages registered with it and allows
the program to acknowledge those stalls and tell the accessing
thread to carry on.
We convert the requests from the kernel into messages back to the
source asking for the pages.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
RAMBlocks that are not a multiple of host pages in length
cause problems for postcopy (I've seen an ACPI table on aarch64
be 5k in length - i.e. 5x target-page), so round RAMBlock sizes
up to a host-page.
This potentially breaks migration compatibility due to changes
in RAMBlock sizes; however:
1) x86 and s390 I think always have host=target page size
2) When I've tried on Power the block sizes already seem aligned.
3) I don't think there's anything else that maintains per-version
machine-types for compatibility.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Prior to the start of postcopy, ensure that everything that will
be transferred later is a whole host-page in size.
This is accomplished by discarding partially transferred host pages
and marking any that are partially dirty as fully dirty.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
During the postcopy phase we must not call the iterate method on
precopy-only devices, since they may have done some cleanup during
the _complete call at the end of the precopy phase.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Once we're in postcopy the source processors are stopped and memory
shouldn't change any more, so there's no need to look at the dirty
map.
There are two notes to this:
1) If we do resync and a page had changed then the page would get
sent again, which the destination wouldn't allow (since it might
have also modified the page)
2) Before disabling this I'd seen very rare cases where a page had been
marked dirtied although the memory contents are apparently identical
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Ensure that target pages received within a host page are in order.
This shouldn't trigger, but in the cases where the sender goes
wrong and sends stuff out of order it produces a corruption that's
really nasty to debug.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
In postcopy, the destination guest is running at the same time
as it's receiving pages; as we receive new pages we must put
them into the guests address space atomically to avoid a running
CPU accessing a partially written page.
Use the helpers in postcopy-ram.c to map these pages.
qemu_get_buffer_in_place is used to avoid a copy out of qemu_file
in the case that postcopy is going to do a copy anyway.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
postcopy_place_page (etc) provide a way for postcopy to place a page
into guests memory atomically (using the copy ioctl on the ufd).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
When transmitting RAM pages, consume pages that have been queued by
MIG_RPCOMM_REQPAGE commands and send them ahead of normal page scanning.
Note:
a) After a queued page the linear walk carries on from after the
unqueued page; there is a reasonable chance that the destination
was about to ask for other closeby pages anyway.
b) We have to be careful of any assumptions that the page walking
code makes, in particular it does some short cuts on its first linear
walk that break as soon as we do a queued page.
c) We have to be careful to not break up host-page size chunks, since
this makes it harder to place the pages on the destination.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
On receiving MIG_RPCOMM_REQ_PAGES look up the address and
queue the page.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add MIG_RP_MSG_REQ_PAGES command on Return path for the postcopy
destination to request a page from the source.
Two versions exist:
MIG_RP_MSG_REQ_PAGES_ID that includes a RAMBlock name and start/len
MIG_RP_MSG_REQ_PAGES that just has start/len for use with the same
RAMBlock as a previous MIG_RP_MSG_REQ_PAGES_ID
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The end of migration in postcopy is a bit different since some of
the things normally done at the end of migration have already been
done on the transition to postcopy.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Rework the migration thread to setup and start postcopy.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Mark the area of RAM as 'userfault'
Start up a fault-thread to handle any userfaults we might receive
from it (to be filled in later)
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Soon we'll be in either ACTIVE or POSTCOPY_ACTIVE when we
complete migration, and we need to know which we expect to be
in to change state safely.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Maintain an 'unsentmap' of pages that have yet to be sent.
This is used in the following patches to discard some set of
the pages already sent as we enter postcopy mode.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add qemu_savevm_state_complete_postcopy to complement
qemu_savevm_state_complete_precopy together with a new
save_live_complete_postcopy method on devices.
The save_live_complete_precopy method is called on
all devices during a precopy migration, and all non-postcopy
devices during a postcopy migration at the transition.
The save_live_complete_postcopy method is called at
the end of postcopy for all postcopiable devices.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
VMDescription is normally sent at the end, after all
of the devices; however that's not the end for postcopy,
so just don't send it when in postcopy.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
'MIGRATION_STATUS_POSTCOPY_ACTIVE' is entered after migrate_start_postcopy
'migration_in_postcopy' is provided for other sections to know if
they're in postcopy.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Soon we'll be in either ACTIVE or POSTCOPY_ACTIVE when we
complete migration, and we need to know which we expect to be
in to change state safely.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Once postcopy is enabled (with migrate_set_capability), the migration
will still start on precopy mode. To cause a transition into postcopy
the:
migrate_start_postcopy
command must be issued. Postcopy will start sometime after this
(when it's next checked in the migration loop).
Issuing the command before migration has started will error,
and issuing after it has finished is ignored.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Provide a check to see if the OS we're running on has all the bits
needed for postcopy.
Creates postcopy-ram.c which will get most of the other helpers we need.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Modify save_live_pending to return separate postcopiable and
non-postcopiable counts.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
MIG_CMD_PACKAGED is a migration command that wraps a chunk of migration
stream inside a package whose length can be determined purely by reading
its header. The destination guarantees that the whole MIG_CMD_PACKAGED
is read off the stream prior to parsing the contents.
This is used by postcopy to load device state (from the package)
while leaving the main stream free to receive memory pages.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The state of the postcopy process is managed via a series of messages;
* Add wrappers and handlers for sending/receiving these messages
* Add state variable that track the current state of postcopy
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
The 'postcopy ram' capability allows postcopy migration of RAM;
note that the migration starts off in precopy mode until
postcopy mode is triggered (see the migrate_start_postcopy
patch later in the series).
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Postcopy needs to have two migration streams loading concurrently;
one from memory (with the device state) and the other from the fd
with the memory transactions.
Split the core of qemu_loadvm_state out so we can use it for both.
Allow the inner loadvm loop to quit and cause the parent loops to
exit as well.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Open a return path, and handle messages that are received upon it.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add 'migration_is_setup_or_active' utility function to check state.
(It gets postcopy added to it's list later on in the series)
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add migrate_send_rp_message to send a message from destination to source along the return path.
(It uses a mutex to let it be called from multiple threads)
Add migrate_send_rp_shut to send a 'shut' message to indicate
the destination is finished with the RP.
Add migrate_send_rp_ack to send a 'PONG' message in response to a PING
Use it in the MSG_RP_PING handler
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Add two src->dest commands:
* OPEN_RETURN_PATH - To request that the destination open the return path
* PING - Request an acknowledge from the destination
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
