Documentation says for WDA '0: Assert WDOG output.' and for SRS
'0: Assert system reset signal.'.
Signed-off-by: Roman Kapl <rka@sysgo.com>
Message-id: 20200207095409.11227-1-rka@sysgo.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The only difference to hardware revision 4 is that the device doesn't
switch to VGA mode in case someone happens to touch a VGA register,
which should make things more robust in configurations with multiple
vga devices.
Swtiching back to VGA mode happens on reset, either full machine
reset or qxl device reset (QXL_IO_RESET ioport command).
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-id: 20200206074358.4274-1-kraxel@redhat.com
For usb2 bMaxPacketSize0 is "n", for usb3 it is "1 << n",
so it must be 9 not 64 ...
rom "Universal Serial Bus 3.1 Specification":
If the device is operating at Gen X speed, the bMaxPacketSize0
field shall be set to 09H indicating a 512-byte maximum packet.
An Enhanced SuperSpeed device shall not support any other maximum
packet sizes for the default control pipe (endpoint 0) control
endpoint.
We now announce a 512-byte maximum packet.
Fixes: 89a453d4a5 ("uas-uas: usb3 streams")
Reported-by: Benjamin David Lunt <fys@fysnet.net>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200117073716.31335-1-kraxel@redhat.com
We extend QEMU RISC-V virt machine by adding Goldfish RTC device
to it. This will allow Guest Linux to sync it's local date/time
with Host date/time via RTC device.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
This patch adds model for Google Goldfish virtual platform RTC device.
We will be adding Goldfish RTC device to the QEMU RISC-V virt machine
for providing real date-time to Guest Linux. The corresponding Linux
driver for Goldfish RTC device is already available in upstream Linux.
For now, VM migration support is available but untested for Goldfish RTC
device. It will be hardened in-future when we implement VM migration for
KVM RISC-V.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
The SiFive test device found on virt machine can be used by
generic syscon reboot and poweroff drivers available in Linux
kernel.
This patch updates FDT generation in virt machine so that
Linux kernel can probe and use generic syscon drivers.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
- some more protocol sanity checks
- qtest for readdir
- Christian Schoenebeck now official reviewer
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEtIKLr5QxQM7yo0kQcdTV5YIvc9YFAl4+c3IACgkQcdTV5YIv
c9Z0eA/8Dpl4KpT2GosgsCj9iqGnT25B0UYiVdLL3aYsJfCgoD7MV0b/v6cK30SI
XyJS2sAMMdGUfOhy+dRUVzSwwKtQOUR9s8zudD5zZ95CtDBGd0c8KdX6TktXRv7U
pnxej9zL29b9+OK6zTv7jzPmpiTkJ1AXa4Rs59DccBaGn3AItgN9VRkOWylMiNir
m4EJh/v5BBTvO9754nExKwgsQHt9eX6jmp+uiRwC2bFirIIbt9bQdwUlX8km03Ml
Qm8gdpJaBgBubFwH1LvN/DPX0JnShGbGonO1zq8SS9NUkZJuSPtI3LY+X1oC9Wgi
ZWLnGc9yTAeaABeg5Hk2jGapxtSL3qEEZUKitRJFrnmSe+R0PcAdjuN9DZEl56rP
zOj0+YUtUggoRd0iwzlZkpga8mKnGM63jovT6cOOTXuLWoh4VlsvBnZSguxKjT2x
rwuEjNA/ctsT5sl6Q++iM8AlrQmrajKphFpT19MtalUN9pNlk2C8PPBQ3xPVTlwT
V3YO4x49hkKbJIUoWqNRwwTQUVsFr3vkhf4IJwq7MBC++wPBoq9W1kQsjcxiZfDP
m1drND5AM9d7E8PAgGsvNO2C41rH7funoZo+NVrrz+Sb01JJI+pE1A2mKrIsTvmh
uxAEv+U6dqS/EjCTY1lyAiM5nLN0qZ8IQiPO1+yxJmkbDJIuJgM=
=oMrh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/9p-next-2020-02-08' into staging
9p patches:
- some more protocol sanity checks
- qtest for readdir
- Christian Schoenebeck now official reviewer
# gpg: Signature made Sat 08 Feb 2020 08:38:10 GMT
# gpg: using RSA key B4828BAF943140CEF2A3491071D4D5E5822F73D6
# gpg: Good signature from "Greg Kurz <groug@kaod.org>" [full]
# gpg: aka "Gregory Kurz <gregory.kurz@free.fr>" [full]
# gpg: aka "[jpeg image of size 3330]" [full]
# Primary key fingerprint: B482 8BAF 9431 40CE F2A3 4910 71D4 D5E5 822F 73D6
* remotes/gkurz/tags/9p-next-2020-02-08:
MAINTAINERS: 9pfs: Add myself as reviewer
tests/virtio-9p: added readdir test
hw/9pfs/9p-synth: added directory for readdir test
9pfs: validate count sent by client with T_readdir
9pfs: require msize >= 4096
tests/virtio-9p: add terminating null in v9fs_string_read()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will provide the following virtual files by the 9pfs
synth driver:
- /ReadDirDir/ReadDirFile99
- /ReadDirDir/ReadDirFile98
...
- /ReadDirDir/ReadDirFile1
- /ReadDirDir/ReadDirFile0
This virtual directory and its virtual 100 files will be
used by the upcoming 9pfs readdir tests.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <5408c28c8de25dd575b745cef63bf785305ccef2.1579567020.git.qemu_oss@crudebyte.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
A good 9p client sends T_readdir with "count" parameter that's sufficiently
smaller than client's initially negotiated msize (maximum message size).
We perform a check for that though to avoid the server to be interrupted
with a "Failed to encode VirtFS reply type 41" transport error message by
bad clients. This count value constraint uses msize - 11, because 11 is the
header size of R_readdir.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <3990d3891e8ae2074709b56449e96ab4b4b93b7d.1579567020.git.qemu_oss@crudebyte.com>
[groug: added comment ]
Signed-off-by: Greg Kurz <groug@kaod.org>
A client establishes a session by sending a Tversion request along with a
'msize' parameter which client uses to suggest server a maximum message
size ever to be used for communication (for both requests and replies)
between client and server during that session. If client suggests a 'msize'
smaller than 4096 then deny session by server immediately with an error
response (Rlerror for "9P2000.L" clients or Rerror for "9P2000.u" clients)
instead of replying with Rversion.
So far any msize submitted by client with Tversion was simply accepted by
server without any check. Introduction of some minimum msize makes sense,
because e.g. a msize < 7 would not allow any subsequent 9p operation at
all, because 7 is the size of the header section common by all 9p message
types.
A substantial higher value of 4096 was chosen though to prevent potential
issues with some message types. E.g. Rreadlink may yield up to a size of
PATH_MAX which is usually 4096, and like almost all 9p message types,
Rreadlink is not allowed to be truncated by the 9p protocol. This chosen
size also prevents a similar issue with Rreaddir responses (provided client
always sends adequate 'count' parameter with Treaddir), because even though
directory entries retrieval may be split up over several T/Rreaddir
messages; a Rreaddir response must not truncate individual directory entries
though. So msize should be large enough to return at least one directory
entry with the longest possible file name supported by host. Most file
systems support a max. file name length of 255. Largest known file name
lenght limit would be currently ReiserFS with max. 4032 bytes, which is
also covered by this min. msize value because 4032 + 35 < 4096.
Furthermore 4096 is already the minimum msize of the Linux kernel's 9pfs
client.
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <8ceecb7fb9fdbeabbe55c04339349a36929fb8e3.1579567019.git.qemu_oss@crudebyte.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Commit ed65fd1a27 ("virtio-blk: switch off scsi-passthrough by
default") changed the default value of the 'scsi' property of
virtio-blk, which is only available on Linux hosts. It also added
an unconditional compat entry for 2.4 or earlier machines.
Trying to set this property on a pre-2.5 machine on OSX, we get:
Unexpected error in object_property_find() at qom/object.c:1201:
qemu-system-x86_64: -device virtio-blk-pci,id=scsi0,drive=drive0: can't apply global virtio-blk-device.scsi=true: Property '.scsi' not found
Fix this error by marking the property optional.
Fixes: ed65fd1a27 ("virtio-blk: switch off scsi-passthrough by default")
Suggested-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200207001404.1739-1-philmd@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
There is a memory leak when we call 'device_list_properties' with typename = stellaris-gptm. It's easy to reproduce as follow:
virsh qemu-monitor-command vm1 --pretty '{"execute": "device-list-properties", "arguments": {"typename": "stellaris-gptm"}}'
This patch delay timer_new in realize to fix it.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200205070659.22488-4-pannengyuan@huawei.com
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a memory leak when we call 'device_list_properties' with typename = stm32f2xx_timer. It's easy to reproduce as follow:
virsh qemu-monitor-command vm1 --pretty '{"execute": "device-list-properties", "arguments": {"typename": "stm32f2xx_timer"}}'
This patch delay timer_new to fix this memleaks.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200205070659.22488-3-pannengyuan@huawei.com
Cc: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a memory leak when we call 'device_list_properties' with typename = armv7m_systick. It's easy to reproduce as follow:
virsh qemu-monitor-command vm1 --pretty '{"execute": "device-list-properties", "arguments": {"typename": "armv7m_systick"}}'
This patch delay timer_new to fix this memleaks.
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Message-id: 20200205070659.22488-2-pannengyuan@huawei.com
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
TD (two dimensions) DMA mode did not work, because the xlen variable
has not been re-initialized before each additional ylen run through
in bcm2835_dma_update(). Fix it.
Signed-off-by: Rene Stange <rsta2@o2online.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In TD (two dimensions) DMA mode ylen has to be increased by one after
reading it from the TXFR_LEN register, because a value of zero has to
result in one run through of the ylen loop. This has been tested on a
real Raspberry Pi 3 Model B+. In the previous implementation the ylen
loop was not passed at all for a value of zero.
Signed-off-by: Rene Stange <rsta2@o2online.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The IGD quirk code defines a separate device, the so-called
"vfio-pci-igd-lpc-bridge" which shows up as a user-creatable
device in all QEMU binaries that include the vfio code. This
is a little bit unfortunate for two reasons: First, this device
is completely useless in binaries like qemu-system-s390x.
Second we also would like to disable it in downstream RHEL
which currently requires some extra patches there since the
device does not have a proper Kconfig-style switch yet.
So it would be good if the device could be disabled more easily,
thus let's move the code to a separate file instead and introduce
a proper Kconfig switch for it which gets only enabled by default
if we also have CONFIG_PC_PCI enabled.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
QEMU currently crashes when the user tries to use the "vmmouse" on a
machine without vmport, e.g.:
$ x86_64-softmmu/qemu-system-x86_64 -machine microvm -device vmmouse
Segmentation fault (core dumped)
or:
$ x86_64-softmmu/qemu-system-x86_64 -device vmmouse -M pc,vmport=off
Segmentation fault (core dumped)
Let's avoid the crash by checking for the vmport device first.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Message-Id: <20200129112954.4282-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
While removing the bluetooth code some weeks ago, I had to leave the
hw/bt/Kconfig file around. Otherwise some of the builds would have been
broken since the generated dependency files tried to include it before
they were rebuilt. Meanwhile, all those dependency files should have
been updated, so we can remove the empty Kconfig file now, too.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20200123064525.6935-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Nothing from "sysemu/cpus.h" is used by smbios.c, remove the include.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20200109112504.32622-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The PARISC Lasi chipset emulation requires some of the common parallel
support and fails to build on a --without-default-devices:
LINK hppa-softmmu/qemu-system-hppa
/usr/bin/ld: hw/hppa/lasi.o: in function `lasi_init':
hw/hppa/lasi.c:324: undefined reference to `parallel_mm_init'
collect2: error: ld returned 1 exit status
make[1]: *** [Makefile:206: qemu-system-hppa] Error 1
Fixes: 376b851909
Reported-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200129192350.27143-1-philmd@redhat.com>
Acked-by: Helge Deller <deller@gmx.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The i8042 PS/2 Controller should not be enabled by default. It has
to be selected by machines or chipsets (e.g. SuperIO chipsets).
Message-Id: <20200115113748.24757-1-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We have many files that apparently do not depend on the target CPU
configuration, i.e. which can be put into common-obj-y instead of
obj-y. This way, the code can be shared for example between
qemu-system-arm and qemu-system-aarch64, or the various big and
little endian variants like qemu-system-sh4 and qemu-system-sh4eb,
so that we do not have to compile the code multiple times anymore.
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200130133841.10779-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The define is only used in one other place. Move the code there
instead of keeping this xen-specific define in sysemu.h.
Message-Id: <20200121161747.10569-1-thuth@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
This patch sets the default value of SPAPR_CAP_FWNMI_MCE
to SPAPR_CAP_ON for machine type 5.0.
Signed-off-by: Aravinda Prasad <arawinda.p@gmail.com>
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Message-Id: <20200130184423.20519-8-ganeshgr@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch includes migration support for machine check
handling. Especially this patch blocks VM migration
requests until the machine check error handling is
complete as these errors are specific to the source
hardware and is irrelevant on the target hardware.
Signed-off-by: Aravinda Prasad <arawinda.p@gmail.com>
[Do not set FWNMI cap in post_load, now its done in .apply hook]
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Message-Id: <20200130184423.20519-7-ganeshgr@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch adds support in QEMU to handle "ibm,nmi-register"
and "ibm,nmi-interlock" RTAS calls.
The machine check notification address is saved when the
OS issues "ibm,nmi-register" RTAS call.
This patch also handles the case when multiple processors
experience machine check at or about the same time by
handling "ibm,nmi-interlock" call. In such cases, as per
PAPR, subsequent processors serialize waiting for the first
processor to issue the "ibm,nmi-interlock" call. The second
processor that also received a machine check error waits
till the first processor is done reading the error log.
The first processor issues "ibm,nmi-interlock" call
when the error log is consumed.
Signed-off-by: Aravinda Prasad <arawinda.p@gmail.com>
[Register fwnmi RTAS calls in core_rtas_register_types()
where other RTAS calls are registered]
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Message-Id: <20200130184423.20519-6-ganeshgr@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Upon a machine check exception (MCE) in a guest address space,
KVM causes a guest exit to enable QEMU to build and pass the
error to the guest in the PAPR defined rtas error log format.
This patch builds the rtas error log, copies it to the rtas_addr
and then invokes the guest registered machine check handler. The
handler in the guest takes suitable action(s) depending on the type
and criticality of the error. For example, if an error is
unrecoverable memory corruption in an application inside the
guest, then the guest kernel sends a SIGBUS to the application.
For recoverable errors, the guest performs recovery actions and
logs the error.
Signed-off-by: Aravinda Prasad <arawinda.p@gmail.com>
[Assume SLOF has allocated enough room for rtas error log]
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200130184423.20519-5-ganeshgr@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Memory error such as bit flips that cannot be corrected
by hardware are passed on to the kernel for handling.
If the memory address in error belongs to guest then
the guest kernel is responsible for taking suitable action.
Patch [1] enhances KVM to exit guest with exit reason
set to KVM_EXIT_NMI in such cases. This patch handles
KVM_EXIT_NMI exit.
[1] https://www.spinics.net/lists/kvm-ppc/msg12637.html
(e20bbd3d and related commits)
Signed-off-by: Aravinda Prasad <arawinda.p@gmail.com>
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200130184423.20519-4-ganeshgr@linux.ibm.com>
[dwg: #ifdefs to fix compile for 32-bit target]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce fwnmi an spapr capability and add a helper function
which tries to enable it, which would be used by following patch
of the series. This patch by itself does not change the existing
behavior.
Signed-off-by: Aravinda Prasad <arawinda.p@gmail.com>
[eliminate cap_ppc_fwnmi, add fwnmi cap to migration state
and reprhase the commit message]
Signed-off-by: Ganesh Goudar <ganeshgr@linux.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200130184423.20519-3-ganeshgr@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For POWER9 DD2.2 cpus, the best current Spectre v2 indirect branch
mitigation is "count cache disabled", which is configured with:
-machine cap-ibs=fixed-ccd
However, this option isn't available on DD2.3 CPUs with KVM, because they
don't have the count cache disabled.
For POWER9 DD2.3 cpus, it is "count cache flush with assist", configured
with:
-machine cap-ibs=workaround,cap-ccf-assist=on
However this option isn't available on DD2.2 CPUs with KVM, because they
don't have the special CCF assist instruction this relies on.
On current machine types, we default to "count cache flush w/o assist",
that is:
-machine cap-ibs=workaround,cap-ccf-assist=off
This runs, with mitigation on both DD2.2 and DD2.3 host cpus, but has a
fairly significant performance impact.
It turns out we can do better. The special instruction that CCF assist
uses to trigger a count cache flush is a no-op on earlier CPUs, rather than
trapping or causing other badness. It doesn't, of itself, implement the
mitigation, but *if* we have count-cache-disabled, then the count cache
flush is unnecessary, and so using the count cache flush mitigation is
harmless.
Therefore for the new pseries-5.0 machine type, enable cap-ccf-assist by
default. Along with that, suppress throwing an error if cap-ccf-assist
is selected but KVM doesn't support it, as long as KVM *is* giving us
count-cache-disabled. To allow TCG to work out of the box, even though it
doesn't implement the ccf flush assist, downgrade the error in that case to
a warning. This matches several Spectre mitigations where we allow TCG
to operate for debugging, since we don't really make guarantees about TCG
security properties anyway.
While we're there, make the TCG warning for this case match that for other
mitigations.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
The PowerNV machine emulates an OpenPOWER system and the PowerNV chip
devices are models of the internal logic of the POWER processor. They
can not be instantiated by the user on the QEMU command line.
The PHB3/PHB4 devices could be an exception in the future after some
rework on how the device tree is built. For the moment, exclude them
also.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200129113720.7404-1-clg@kaod.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is a model of the PCIe Host Bridge (PHB3) found on a POWER8
processor. It includes the PowerBus logic interface (PBCQ), IOMMU
support, a single PCIe Gen.3 Root Complex, and support for MSI and LSI
interrupt sources as found on a POWER8 system using the XICS interrupt
controller.
The POWER8 processor comes in different flavors: Venice, Murano,
Naple, each having a different number of PHBs. To make things simpler,
the models provides 3 PHB3 per chip. Some platforms, like the
Firestone, can also couple PHBs on the first chip to provide more
bandwidth but this is too specific to model in QEMU.
XICS requires some adjustment to support the PHB3 MSI. The changes are
provided here but they could be decoupled in prereq patches.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200127144506.11132-3-clg@kaod.org>
[dwg: Use device_class_set_props()]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These changes introduces models for the PCIe Host Bridge (PHB4) of the
POWER9 processor. It includes the PowerBus logic interface (PBCQ),
IOMMU support, a single PCIe Gen.4 Root Complex, and support for MSI
and LSI interrupt sources as found on a POWER9 system using the XIVE
interrupt controller.
POWER9 processor comes with 3 PHB4 PEC (PCI Express Controller) and
each PEC can have several PHBs. By default,
* PEC0 provides 1 PHB (PHB0)
* PEC1 provides 2 PHBs (PHB1 and PHB2)
* PEC2 provides 3 PHBs (PHB3, PHB4 and PHB5)
Each PEC has a set "global" registers and some "per-stack" (per-PHB)
registers. Those are organized in two XSCOM ranges, the "Nest" range
and the "PCI" range, each range contains both some "PEC" registers and
some "per-stack" registers.
No default device layout is provided and PCI devices can be added on
any of the available PCIe Root Port (pcie.0 .. 2 of a Power9 chip)
with address 0x0 as the firwware (skiboot) only accepts a single
device per root port. To run a simple system with a network and a
storage adapters, use a command line options such as :
-device e1000e,netdev=net0,mac=C0:FF:EE:00:00:02,bus=pcie.0,addr=0x0
-netdev bridge,id=net0,helper=/usr/libexec/qemu-bridge-helper,br=virbr0,id=hostnet0
-device megasas,id=scsi0,bus=pcie.1,addr=0x0
-drive file=$disk,if=none,id=drive-scsi0-0-0-0,format=qcow2,cache=none
-device scsi-hd,bus=scsi0.0,channel=0,scsi-id=0,lun=0,drive=drive-scsi0-0-0-0,id=scsi0-0-0-0,bootindex=2
If more are needed, include a bridge.
Multi chip is supported, each chip adding its set of PHB4 controllers
and its PCI busses. The model doesn't emulate the EEH error handling.
This model is not ready for hotplug yet.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[ clg: - numerous cleanups
- commit log
- fix for broken LSI support
- PHB pic printinfo
- large QOM rework ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200127144506.11132-2-clg@kaod.org>
[dwg: Use device_class_set_props()]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200121152935.649898-6-stefanb@linux.ibm.com>
[dwg: Use default in Kconfig rather than select to avoid breaking
Windows host build]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Extend the tpm_spapr frontend with VM suspend and resume support.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Message-Id: <20200121152935.649898-5-stefanb@linux.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Implement support for TPM on ppc64 by implementing the vTPM CRQ interface
as a frontend. It can use the tpm_emulator driver backend with the external
swtpm.
The Linux vTPM driver for ppc64 works with this emulation.
This TPM emulator also handles the TPM 2 case.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200121152935.649898-4-stefanb@linux.ibm.com>
[dwg: Use device_class_set_props(), tweak Kconfig]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
For devices that cannot be statically initialized, implement a
get_dt_compatible() callback that allows us to ask the device for
the 'compatible' value.
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200121152935.649898-3-stefanb@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20200121152935.649898-2-stefanb@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
When the "hb-mode" option is activated on the powernv machine, the
firmware is mapped at 0x8000000 and the HRMOR of the HW threads are
set to the same address.
The PNOR mapping on the FW address space of the LPC bus is left enabled
to let the firmware load any other images required to boot the host.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200127144154.10170-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 158e17a65e ("ppc/pnv: Link "chip" property to PnvCore::chip
pointer") introduced some cleanups of the PnvCore realize handler.
Let's continue by reworking a bit the interface of the PnvCore
handlers for the CPU threads. These changes make the "core-pir"
property alias unused. Remove it.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200127144154.10170-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the description of "ibm,client-architecture-support" that
can found in LoPAPR "B.6.2.3 Root Node Methods":
If multiple partition processors or threads are active at the time of
the ibm,client-architecture-support method call, or an error is detected
in the format of the ibm,architecture.vec structure, the err? boolean
shall be TRUE; else FALSE.
We certainly don't want to temper with the platform or with the PCR of
the other vCPUs if they happen to be active. Ensure we have only one
active vCPU and fail CAS otherwise. This is just for conformance and
robustness, it doesn't fix any known bugs.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <157969867170.571404.12117797348882189656.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Most of the option vector helpers have assertions to check their
arguments aren't null. The guest can provide an arbitrary address
for the CAS structure that would result in such null arguments.
Fail CAS with H_PARAMETER and print a warning instead of aborting
QEMU.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <157925255250.397143.10855183619366882459.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
It's been deprecated since QEMU v3.1. The 40p machine should be
used nowadays instead.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200114114617.28854-1-thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <1579100861-73692-71-git-send-email-imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Print out the offset at which the error occured.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200108090348.21224-3-clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200108090348.21224-2-clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The preferred way to test whether a trace event is enabled is to
use trace_event_get_state_backends(), because this will give the
correct answer (allowing expensive computations to be skipped)
whether the trace event is compile-time or run-time disabled.
Convert the old-style direct use of TRACE_FOO_ENABLED.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20200120151142.18954-4-peter.maydell@linaro.org
Message-Id: <20200120151142.18954-4-peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
kvm-no-adjvtime is a KVM specific CPU property and a first of its
kind. To accommodate it we also add kvm_arm_add_vcpu_properties()
and a KVM specific CPU properties description to the CPU features
document.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20200120101023.16030-7-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20200120101023.16030-3-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If LPIs are disabled, KVM will just ignore the GICR_PENDBASER.PTZ bit when
restoring GICR_CTLR. Setting PTZ here makes littlt sense in "reduce GIC
initialization time".
And what's worse, PTZ is generally programmed by guest to indicate to the
Redistributor whether the LPI Pending table is zero when enabling LPIs.
If migration is triggered when the PTZ has just been cleared by guest (and
before enabling LPIs), we will see PTZ==1 on the destination side, which
is not as expected. Let's just drop this hackish userspace behavior.
Also take this chance to refine the comment a bit.
Fixes: 367b9f527b ("hw/intc/arm_gicv3_kvm: Implement get/put functions")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Message-id: 20200119133051.642-1-yuzenghui@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace deprecated qdev_reset_all by resettable_cold_reset_fn for
the ipl registration in the main reset handlers.
This does not impact the behavior for the following reasons:
+ at this point resettable just call the old reset methods of devices
and buses in the same order than qdev/qbus.
+ resettable handlers registered with qemu_register_reset are
serialized; there is no interleaving.
+ eventual explicit calls to legacy reset API (device_reset or
qdev/qbus_reset) inside this reset handler will not be masked out
by resettable mechanism; they do not go through resettable api.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20200123132823.1117486-12-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Deprecate device_legacy_reset(), qdev_reset_all() and
qbus_reset_all() to be replaced by new functions
device_cold_reset() and bus_cold_reset() which uses resettable API.
Also introduce resettable_cold_reset_fn() which may be used as a
replacement for qdev_reset_all_fn and qbus_reset_all_fn().
Following patches will be needed to look at legacy reset call sites
and switch to resettable api. The legacy functions will be removed
when unused.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-9-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit make use of the resettable API to reset the device being
hotplugged when it is realized. Also it ensures it is put in a reset
state coherent with the parent it is plugged into.
Note that there is a difference in the reset. Instead of resetting
only the hotplugged device, we reset also its subtree (switch to
resettable API). This is not expected to be a problem because
sub-buses are just realized too. If a hotplugged device has any
sub-buses it is logical to reset them too at this point.
The recently added should_be_hidden and PCI's partially_hotplugged
mechanisms do not interfere with realize operation:
+ In the should_be_hidden use case, device creation is
delayed.
+ The partially_hotplugged mechanism prevents a device to be
unplugged and unrealized from qdev POV and unrealized.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-8-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In qdev_set_parent_bus(), when changing the parent bus of a
realized device, if the source and destination buses are not in the
same reset state, some adaptations are required. This patch adds
needed call to resettable_change_parent() to make sure a device reset
state stays coherent with its parent bus.
The addition is a no-op if:
1. the device being parented is not realized.
2. the device is realized, but both buses are not under reset.
Case 2 means that as long as qdev_set_parent_bus() is called
during the machine realization procedure (which is before the
machine reset so nothing is in reset), it is a no op.
There are 52 call sites of qdev_set_parent_bus(). All but one fall
into the no-op case:
+ 29 trivial calls related to virtio (in hw/{s390x,display,virtio}/
{vhost,virtio}-xxx.c) to set a vdev(or vgpu) composing device
parent bus just before realizing the same vdev(vgpu).
+ hw/core/qdev.c: when creating a device in qdev_try_create()
+ hw/core/sysbus.c: when initializing a device in the sysbus
+ hw/i386/amd_iommu.c: before realizing AMDVIState/pci
+ hw/isa/piix4.c: before realizing PIIX4State/rtc
+ hw/misc/auxbus.c: when creating an AUXBus
+ hw/misc/auxbus.c: when creating an AUXBus child
+ hw/misc/macio/macio.c: when initializing a MACIOState child
+ hw/misc/macio/macio.c: before realizing NewWorldMacIOState/pmu
+ hw/misc/macio/macio.c: before realizing NewWorldMacIOState/cuda
+ hw/net/virtio-net.c: Used for migration when using the failover
mechanism to migration a vfio-pci/net. It is
a no-op because at this point the device is
already on the bus.
+ hw/pci-host/designware.c: before realizing DesignwarePCIEHost/root
+ hw/pci-host/gpex.c: before realizing GPEXHost/root
+ hw/pci-host/prep.c: when initialiazing PREPPCIState/pci_dev
+ hw/pci-host/q35.c: before realizing Q35PCIHost/mch
+ hw/pci-host/versatile.c: when initializing PCIVPBState/pci_dev
+ hw/pci-host/xilinx-pcie.c: before realizing XilinxPCIEHost/root
+ hw/s390x/event-facility.c: when creating SCLPEventFacility/
TYPE_SCLP_QUIESCE
+ hw/s390x/event-facility.c: ditto with SCLPEventFacility/
TYPE_SCLP_CPU_HOTPLUG
+ hw/s390x/sclp.c: Not trivial because it is called on a SLCPDevice
just after realizing it. Ok because at this point the destination
bus (sysbus) is not in reset; the realize step is before the
machine reset.
+ hw/sd/core.c: Not OK. Used in sdbus_reparent_card(). See below.
+ hw/ssi/ssi.c: Used to put spi slave on spi bus and connect the cs
line in ssi_auto_connect_slave(). Ok because this function is only
used in realize step in hw/ssi/aspeed_smc.ci, hw/ssi/imx_spi.c,
hw/ssi/mss-spi.c, hw/ssi/xilinx_spi.c and hw/ssi/xilinx_spips.c.
+ hw/xen/xen-legacy-backend.c: when creating a XenLegacyDevice device
+ qdev-monitor.c: in device hotplug creation procedure before realize
Note that this commit alone will have no effect, right now there is no
use of resettable API to reset anything. So a bus will never be tagged
as in-reset by this same API.
The one place where side-effect will occurs is in hw/sd/core.c in
sdbus_reparent_card(). This function is only used in the raspi machines,
including during the sysbus reset procedure. This case will be
carrefully handled when doing the multiple phase reset transition.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-7-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a function resettable_change_parent() to do the required
plumbing when changing the parent a of Resettable object.
We need to make sure that the reset state of the object remains
coherent with the reset state of the new parent.
We make the 2 following hypothesis:
+ when an object is put in a parent under reset, the object goes in
reset.
+ when an object is removed from a parent under reset, the object
leaves reset.
The added function avoids any glitch if both old and new parent are
already in reset.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-6-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit adds support of Resettable interface to buses and devices:
+ ResettableState structure is added in the Bus/Device state
+ Resettable methods are implemented.
+ device/bus_is_in_reset function defined
This commit allows to transition the objects to the new
multi-phase interface without changing the reset behavior at all.
Object single reset method can be split into the 3 different phases
but the 3 phases are still executed in a row for a given object.
From the qdev/qbus reset api point of view, nothing is changed.
qdev_reset_all() and qbus_reset_all() are not modified as well as
device_legacy_reset().
Transition of an object must be done from parent class to child class.
Care has been taken to allow the transition of a parent class
without requiring the child classes to be transitioned at the same
time. Note that SysBus and SysBusDevice class do not need any transition
because they do not override the legacy reset method.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-5-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit defines an interface allowing multi-phase reset. This aims
to solve a problem of the actual single-phase reset (built in
DeviceClass and BusClass): reset behavior is dependent on the order
in which reset handlers are called. In particular doing external
side-effect (like setting an qemu_irq) is problematic because receiving
object may not be reset yet.
The Resettable interface divides the reset in 3 well defined phases.
To reset an object tree, all 1st phases are executed then all 2nd then
all 3rd. See the comments in include/hw/resettable.h for a more complete
description. The interface defines 3 phases to let the future
possibility of holding an object into reset for some time.
The qdev/qbus reset in DeviceClass and BusClass will be modified in
following commits to use this interface. A mechanism is provided
to allow executing a transitional reset handler in place of the 2nd
phase which is executed in children-then-parent order inside a tree.
This will allow to transition devices and buses smoothly while
keeping the exact current qdev/qbus reset behavior for now.
Documentation will be added in a following commit.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-4-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds trace events to reset procedure and when updating the parent
bus of a device.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-3-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Provide a temporary device_legacy_reset function doing what
device_reset does to prepare for the transition with Resettable
API.
All occurrence of device_reset in the code tree are also replaced
by device_legacy_reset.
The new resettable API has different prototype and semantics
(resetting child buses as well as the specified device). Subsequent
commits will make the changeover for each call site individually; once
that is complete device_legacy_reset() will be removed.
Signed-off-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200123132823.1117486-2-damien.hedde@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since we enabled parallel TCG code generation for softmmu (see
commit 3468b59 "tcg: enable multiple TCG contexts in softmmu")
and its subsequent fix (commit 72649619 "add .min_cpus and
.default_cpus fields to machine_class"), the raspi machines are
restricted to always use their 4 cores:
See in hw/arm/raspi2 (with BCM283X_NCPUS set to 4):
222 static void raspi2_machine_init(MachineClass *mc)
223 {
224 mc->desc = "Raspberry Pi 2";
230 mc->max_cpus = BCM283X_NCPUS;
231 mc->min_cpus = BCM283X_NCPUS;
232 mc->default_cpus = BCM283X_NCPUS;
235 };
236 DEFINE_MACHINE("raspi2", raspi2_machine_init)
We can no longer use the -smp option, as we get:
$ qemu-system-arm -M raspi2 -smp 1
qemu-system-arm: Invalid SMP CPUs 1. The min CPUs supported by machine 'raspi2' is 4
Since we can not set the TYPE_BCM283x SOC "enabled-cpus" with -smp,
remove the unuseful code.
We can achieve the same by using the '-global bcm2836.enabled-cpus=1'
option.
Reported-by: Laurent Bonnans <laurent.bonnans@here.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20200120235159.18510-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Following the pattern of the work recently done with the ASPEED GPIO
model, this adds support for inspecting and modifying the PCA9552 LEDs
from the monitor.
(qemu) qom-set /machine/unattached/device[17] led0 on
(qemu) qom-set /machine/unattached/device[17] led0 off
(qemu) qom-set /machine/unattached/device[17] led0 pwm0
(qemu) qom-set /machine/unattached/device[17] led0 pwm1
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-6-clg@kaod.org
[clg: - removed the "qom-get" examples from the commit log
- merged memory leak fixes from Joel ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The overhead for the OpenBMC firmware images using the a custom U-Boot
is around 2 seconds, which is fine, but with a U-Boot from mainline,
it takes an extra 50 seconds or so to reach Linux. A quick survey on
the number of reads performed on the flash memory region gives the
following figures :
OpenBMC U-Boot 922478 (~ 3.5 MBytes)
Mainline U-Boot 20569977 (~ 80 MBytes)
QEMU must be trashing the TCG TBs and reloading text very often. Some
addresses are read more than 250.000 times. Until we find a solution
to improve boot time, execution from MMIO is not activated by default.
Setting this option also breaks migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200114103433.30534-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These buffers should be aligned on 16 bytes.
Ignore invalid RX and TX buffer addresses and log an error. All
incoming and outgoing traffic will be dropped because no valid RX or
TX descriptors will be available.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-4-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initialise another SDHCI model instance for the AST2600's eMMC
controller and use the SDHCI's num_slots value introduced previously to
determine whether we should create an SD card instance for the new slot.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-3-clg@kaod.org
[ clg : - removed ternary operator from sdhci_attach_drive()
- renamed SDHCI objects with a '-controller' prefix ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 includes a second cut-down version of the SD/MMC controller
found in the AST2500, named the eMMC controller. It's cut down in the
sense that it only supports one slot rather than two, but it brings the
total number of slots supported by the AST2600 to three.
The existing code assumed that the SD controller always provided two
slots. Rework the SDHCI object to expose the number of slots as a
property to be set by the SoC configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-2-clg@kaod.org
[PMM: fixed up to use device_class_set_props()]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The num-lines property of the TYPE_OR_GATE device sets the number
of input lines it has. An assert() in or_irq_realize() restricts
this to the maximum supported by the implementation. However we
got the condition in the assert wrong: it should be using <=,
because num-lines == MAX_OR_LINES is permitted, and means that
all entries from 0 to MAX_OR_LINES-1 in the s->levels[] array
are used.
We didn't notice this previously because no user has so far
needed that many input lines.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200120142235.10432-1-peter.maydell@linaro.org
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEuBi5yt+QicLVzsZrda1lgCoLQhEFAl4xgjEACgkQda1lgCoL
QhEmhggA4f2WVC23ub14UHFIqjkfWWDBZ2o+TxttuTNk8aAgSC0lLiPTUgDqB9oC
MINP8rXWB10xTzDPTAgi/C1eWBU0J9YUwGQFCXKTs/wYI2MT7ZVEQxV5kHBJ9Ygg
CjLIjMtDtzY6+gjtxzO1r9o3R+dEgi/ztk9p/EDCBfbERtyE2xqsL/rbhDeM0O2e
h5RVTqharUfvGEmSDWaorTMLcsbNJbx9bYC1PbJ3S9TBnDW6UHcTQ6PL7Rs39dU6
4n9VfE6KtfOwKf+plB8cZlerA9M0HoohsPoRhKPQkMhj1SbxD4jO1zyOuahxGJzY
xjmuJfPtFDTeFntpLNy7t66JYsPItw==
=4iNk
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2020-01-29-1' into staging
Merge tpm 2020/01/29 v1
# gpg: Signature made Wed 29 Jan 2020 13:01:37 GMT
# gpg: using RSA key B818B9CADF9089C2D5CEC66B75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* remotes/stefanberger/tags/pull-tpm-2020-01-29-1:
tpm-ppi: page-align PPI RAM
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While loading the executable, some platforms (like AVR) need to
detect CPU type that executable is built for - and, with this patch,
this is enabled by reading the field 'e_flags' of the ELF header of
the executable in question. The change expands functionality of
the following functions:
- load_elf()
- load_elf_as()
- load_elf_ram()
- load_elf_ram_sym()
The argument added to these functions is called 'pflags' and is of
type 'uint32_t*' (that matches 'pointer to 'elf_word'', 'elf_word'
being the type of the field 'e_flags', in both 32-bit and 64-bit
variants of ELF header). Callers are allowed to pass NULL as that
argument, and in such case no lookup to the field 'e_flags' will
happen, and no information will be returned, of course.
CC: Richard Henderson <rth@twiddle.net>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Edgar E. Iglesias <edgar.iglesias@gmail.com>
CC: Michael Walle <michael@walle.cc>
CC: Thomas Huth <huth@tuxfamily.org>
CC: Laurent Vivier <laurent@vivier.eu>
CC: Philippe Mathieu-Daudé <f4bug@amsat.org>
CC: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
CC: Aurelien Jarno <aurelien@aurel32.net>
CC: Jia Liu <proljc@gmail.com>
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
CC: BALATON Zoltan <balaton@eik.bme.hu>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
CC: Thomas Huth <thuth@redhat.com>
CC: Artyom Tarasenko <atar4qemu@gmail.com>
CC: Fabien Chouteau <chouteau@adacore.com>
CC: KONRAD Frederic <frederic.konrad@adacore.com>
CC: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Aleksandar Rikalo <aleksandar.rikalo@rt-rk.com>
Signed-off-by: Michael Rolnik <mrolnik@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Message-Id: <1580079311-20447-24-git-send-email-aleksandar.markovic@rt-rk.com>
post-copy migration fails on destination with error such as:
2019-12-26T10:22:44.714644Z qemu-kvm: ram_block_discard_range:
Unaligned start address: 0x559d2afae9a0
Use qemu_memalign() to constrain the PPI RAM memory alignment.
Cc: qemu-stable@nongnu.org
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Message-id: 20200103074000.1006389-3-marcandre.lureau@redhat.com
The commit a718978ed5 from July 2015 introduced the assertion which
implies that the size of successful DMA transfers handled in ide_dma_cb()
should be multiple of 512 (the size of a sector). But guest systems can
initiate DMA transfers that don't fit this requirement.
For fixing that let's check the number of bytes prepared for the transfer
by the prepare_buf() handler. The code in ide_dma_cb() must behave
according to the Programming Interface for Bus Master IDE Controller
(Revision 1.0 5/16/94):
1. If PRDs specified a smaller size than the IDE transfer
size, then the Interrupt and Active bits in the Controller
status register are not set (Error Condition).
2. If the size of the physical memory regions was equal to
the IDE device transfer size, the Interrupt bit in the
Controller status register is set to 1, Active bit is set to 0.
3. If PRDs specified a larger size than the IDE transfer size,
the Interrupt and Active bits in the Controller status register
are both set to 1.
Signed-off-by: Alexander Popov <alex.popov@linux.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-id: 20191223175117.508990-2-alex.popov@linux.com
Signed-off-by: John Snow <jsnow@redhat.com>
The region in range [0xf0000000 - 0xf1000000] is the PDC area
(Processor Dependent Code), where the firmware is loaded.
This region has higher priority than the main memory.
When the machine has more than 3840MB of RAM, there is an
overlap. Since the PDC is closer to the CPU in the bus
hierarchy, it gets accessed first, and the CPU does not have
access to the RAM in this range.
To model the same behavior and keep a simple memory layout,
reduce the priority of the RAM region. The PDC region ends
overlapping the RAM.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-4-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The hardware expects DIMM slots of 1 or 2 GB, allowing up to
4 GB of memory. We want to accept the same amount of memory the
hardware can deal with. DIMMs of 768MB are not available.
However we have to deal with a firmware limitation: currently
SeaBIOS only supports 32-bit, and expects the RAM size in a
32-bit register. When using a 4GB configuration, the 32-bit
register get truncated and we report a size of 0MB to SeaBIOS,
which ends halting the machine:
$ qemu-system-hppa -m 4g -serial stdio
SeaBIOS: Machine configured with too little memory (0 MB), minimum is 16 MB.
SeaBIOS wants SYSTEM HALT.
The easiest way is to restrict the machine to 3GB of memory.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-3-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The firmware has to reside in the PDC range. If the Elf file
expects to load it below FIRMWARE_START, it is incorrect,
regardless the RAM size.
Acked-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200109000525.24744-2-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This adds emulation of Artist graphics good enough to get a text
console on both Linux and HP-UX. The X11 server from HP-UX also works.
Adjust boot-serial-test to disable graphics, so that SeaBIOS outputs
to the serial port, as expected by the test.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-6-svens@stackframe.org>
[rth: Merge Helge's test for machine->enable_graphics]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Most HP PA-RISC machines have a Digital DS21142/43 Tulip network card,
only some very latest generation machines have an e1000 NIC.
Since qemu now provides an emulated tulip card, use that one instead.
Signed-off-by: Helge Deller <deller@gmx.de>
Message-Id: <20191221222530.GB27803@ls3530.fritz.box>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-5-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
HP-UX sends both the 'Set key make and break (0xfc) and
'Set all key typematic make and break' (0xfa). QEMU response
with 'Resend' as it doesn't handle these commands. HP-UX than
reports an PS/2 max retransmission exceeded error. Add these
commands and just reply with ACK.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-4-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
LASI is a built-in multi-I/O chip which supports serial, parallel,
network (Intel i82596 Apricot), sound and other functionalities.
LASI has been used in many HP PARISC machines.
This patch adds the necessary parts to allow Linux and HP-UX to detect
LASI and the network card.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-Id: <20191220211512.3289-3-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The tests of the dino chip with the Online-diagnostics CD
("ODE DINOTEST") now succeeds.
Additionally add some qemu trace events.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20191220211512.3289-2-svens@stackframe.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
While working on the "Enable adapter interruption suppression again"
recently, I had to discover that the meaning of get_machine_class()
and the related *_allowed() wrappers is not very obvious. Add a more
verbose comment here to clarify how these should be used.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200123170256.12386-1-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
We currently check (by error) if the passed-in Error pointer errp
is non-null and return after realizing the first child of the
event facility in that case. Symptom is that 'virsh shutdown'
does not work, as the sclpquiesce device is not realized.
Fix this by (correctly) checking the local Error err.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 3d508334dd ("s390x/event-facility: Fix realize() error API violations")
Message-Id: <20200121095506.8537-1-cohuck@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
If the kernel irqchip has been disabled, we don't want the
{add,release}_adapter_routes routines to call any kvm_irqchip_*
interfaces, as they may rely on an irqchip actually having been
created. Just take a quick exit in that case instead. If you are
trying to use irqfd without a kernel irqchip, we will fail with
an error.
Also initialize routes->gsi[] with -1 in the virtio-ccw handling,
to make sure we don't trip over other errors, either. (Nobody
else uses the gsi array in that structure.)
Fixes: d426d9fba8 ("s390x/virtio-ccw: wire up irq routing and irqfds")
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20200117111147.5006-1-cohuck@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
'out' label from write_event_mask() and write_event_data()
can be replaced by 'return'.
The 'out' label from read_event_data() can also be replaced.
However, as suggested by Cornelia Huck, instead of simply
replacing the 'out' label, let's also change the code flow
a bit to make it clearer that sccb events are always handled
regardless of the mask for unconditional reads, while selective
reads are handled if the mask is valid.
CC: Cornelia Huck <cohuck@redhat.com>
CC: Thomas Huth <thuth@redhat.com>
CC: Halil Pasic <pasic@linux.ibm.com>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200108144607.878862-1-danielhb413@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
'out' label can be replaced by 'return' with the appropriate
value that is set by 'r' right before the jump.
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20200106182425.20312-42-danielhb413@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
'out' label can be replaced by 'return' with the appropriate
value. The 'r' integer, which is used solely to set the
return value for this label, can also be removed.
CC: Cornelia Huck <cohuck@redhat.com>
CC: Halil Pasic <pasic@linux.ibm.com>
CC: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20200106182425.20312-39-danielhb413@gmail.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
* Cleanups (Philippe)
* virtio-scsi fix (Pan Nengyuan)
* Tweak Skylake-v3 model id (Kashyap)
* x86 UCODE_REV support and nested live migration fix (myself)
* Advisory mode for pvpanic (Zhenwei)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeK1CXAAoJEL/70l94x66DXtkIAI6W5wEY0Yme4M9Q5mGc0RV8
uscPLg0wsg88u6xne8ucCiGymvDREym2ii/aVI0Hi5ish84ZMdCrdck9cd+llpMf
+a3slL26AKlOW8WtYSuyAE1RdLFXngeXdwal5KtWPEExJorkDUPTbwhBzQduQK1a
myoHHcbwdd/96v7FvKnfG8jM6KZtHPQQ0i6+6fX4PN44jaULQNjze8GIrRBEwqw5
uCKJFQPBXiVcxKjH5/kzI1vl2hLJbF2ZGVEzX/U8OPZwyGPHIkWquURo8lvUTPfb
ySlNTUTV2CyrN65TBRXQp/mJi44WvME5Jxlf5rNLBaYXPpL0zhmILKn5X5ya4U0=
=TD0Y
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Register qdev properties as class properties (Marc-André)
* Cleanups (Philippe)
* virtio-scsi fix (Pan Nengyuan)
* Tweak Skylake-v3 model id (Kashyap)
* x86 UCODE_REV support and nested live migration fix (myself)
* Advisory mode for pvpanic (Zhenwei)
# gpg: Signature made Fri 24 Jan 2020 20:16:23 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (58 commits)
build-sys: clean up flags included in the linker command line
target/i386: Add the 'model-id' for Skylake -v3 CPU models
qdev: use object_property_help()
qapi/qmp: add ObjectPropertyInfo.default-value
qom: introduce object_property_help()
qom: simplify qmp_device_list_properties()
vl: print default value in object help
qdev: register properties as class properties
qdev: move instance properties to class properties
qdev: rename DeviceClass.props
qdev: set properties with device_class_set_props()
object: return self in object_ref()
object: release all props
object: add object_class_property_add_link()
object: express const link with link property
object: add direct link flag
object: rename link "child" to "target"
object: check strong flag with &
object: do not free class properties
object: add object_property_set_default
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use class properties facilities to add properties to the class during
device_class_set_props().
qdev_property_add_static() must be adapted as PropertyInfo now
operates with classes (and not instances), so we must
set_default_value() on the ObjectProperty, before calling its init()
method on the object instance.
Also, PropertyInfo.create() is now exclusively used for class
properties. Fortunately, qdev_property_add_static() is only used in
target/arm/cpu.c so far, which doesn't use "link" properties (that
require create()).
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20200110153039.1379601-22-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the one-user function to the place it is being used.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200110153039.1379601-5-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All callers use error_abort, and even the function itself calls with
error_abort.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20200110153039.1379601-4-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
