* objdump.c (disassemble_bytes): Make output of raw instructions
work better for non-standard values of bytes_per_chunk and
bytes_per_line.
I also fixed the spacing in the last patch.
with 0 length. A sticky tag caused this fix from
revision 2.32 date: 1996/04/29 23:25:27; author: dawn;
state: Exp; lines: +1 -0 branches: 2.32.34;
to not make it into devo.
Add prototypes for make_final_cleanup (and the other cleanup
routines.
* remote-e7000.c: Fix sync code to timeout if unable to sync.
Change sync code to report status while trying to sync-up
with hardware. Add debugging output and document.
* ser-e7kpc.c: Swap order of len & offset to match implementation.
Add debugging output and document.
* serial.c: Add debugging output.
* top.c: Add call to do_final_cleanups.
Remove conditionals preventing Win32 from getting SIGQUIT.
* utils.c: (*_cleanup): Modify cleanup routines to accept a cleanup
chain as a parameter. Extract this generic code from the cleanup
routines into separate funtions (*_my_cleanup). Keep old
functionality by passing "cleanup_chain" to the new funtions.
Define the cleanup chain "final_cleanup_chain" to be a cleanup
chain which will be executed only when gdb exits. Add functions
(*_final_cleanup) to match the original (*_cleanup) functions.
(pollquit, quit, notice_quit): Fix to read cntl-C from the
Windows message queue.
(tic80_opcodes): Sort entries so that long immediate forms
come after short immediate forms, making it easier for
assembler to select the right one for a given operand.
(md_apply_fix): Handle BFD_RELOC_MIPS16_GPREL.
* config/tc-mips.c (append_insn): Output jump instruction as a
pair of 2 byte instructions, rather than as a single 4 byte
instruction.
start-sanitize-r5900
* config/tc-mips.c (md_begin): Correct test of mips_5900.
(mips_ip): Don't check INSN_ISA for a macro.
end-sanitize-r5900
be two byte aligned. Round argument sizes up to two byte boundary.
Write out args in two byte hunks.
(mn10200_push_return_address): Implement.
* config/mn10200/tm-mn10200.h (EXTRACT_RETURN_VALUE): Abort for
structures > 8 bytes (temporary).
(STORE_RETURN_VALUE): Likewise.
(CALL_DUMMY): No longer undefine.
(USE_STRUCT_CONVENTION): Use for args > 8 bytes.
(REG_STRUCT_HAS_ADDR): Define.
Inferior function calls for the mn10200.
* config/vxworks.exp: New file.
* gdb.base/a2-run.exp: Change vxworks cases to use gdb_spawn_id.
* config/monitor.exp(gdb_target_monitor): Look for a prompt from
gdb before assuming everything worked. Send a ^C if a timeout
occurs.
Random fixes for vxworks and d10v.
(find_proc_desc): Move non-heuristic proc search code into separate
function.
(gdb_print_insn_mips): Use non-heuristic method to find procedure
descriptor, to avoid prologue examination when disassembling.
* remote-mips.c: Add support for new "lsi" target (LSI MiniRISC
aka MicroMeteor board).
(mips_exit_debug): Prevent protocol reinitialization if an error
occurs while exiting debug mode.
instruction registers, opcodes and formats. Build internal table
for new instructions and provide callbacks for assembler and
disassembler.
* itbl-lex.l, itbl-parse.y: Lex and yacc parsers for instruction
spec table.
* itbl-ops.h: New file. Header file for itbl support.
* config/itbl-mips.h: New file. Mips specific definitions for
itbl support.
comments, formatting, etc. Plus other minor fixes for problems
I found during my first pass over the mn10200 port.
(mn10200_analyze_prologue): New function.
(mn10200_frame_chain, mn10200_init_extra_frame_info): Use it.
* config/mn10200/tm-mn10200.h: Lots of updates/improvements to
comments, formatting, etc. Minor fixes for problems I found during
my first pass over the mn10200 port.
(TARGET_*_BIT): Define appropriately for ints, long longs, doubles and
pointers.
(REGISTER_VIRTUAL_TYPE): Define as a long.
(EXTRACT_RETURN_VALUE): Rework to deal with long ints living
in register pairs.
(STORE_RETURN_VALUE): Similarly.
Checking in my initial changes, prologue scanning, etc.
Current gdb testsuite results:
=== gdb Summary ===
# of expected passes 3684
# of expected failures 40
# of unexpected failures 6
* scripttempl/tic80coff.sc: New (dummy) file for TIc80.
* Makefile.in (etic80coff.c): Add target and rule to build it.
* configure.tgt (tic80-*-coff): Set targ_emul to tic80coff.
from being sent to 32-bit targets by masking off upper bits.
* mips-tdep.c (heuristic_proc_start): Mask off upper 32 bits
of PC on 32-bit targets.
(mips16_heuristic_proc_desc): Recognize 'addiu s1,sp,n' as a
frame setup instruction.
(mips32_heuristic_proc_desc): Fix warning found by gcc -Wall.
(mips16_skip_prologue): Recognize 'addiu s1,sp,n' as a valid
prologue instruction. Fix warnings and bugs found by gcc -Wall.
* buildsym.c (finish_block): Improve handling of overlapping blocks;
fixes problem on MIPS16 printing function arguments.
the linkage name of a die from DW_AT_MIPS_linkage_name or
DW_AT_name.
(read_func_scope, dwarf2_add_field, dwarf2_add_member_fn,
new_symbol): Use it instead of accessing DW_AT_name.
(read_partial_die): Use DW_AT_MIPS_linkage name as name of the
partial die if present.
(dwarf2_add_member_fn): Make a copy of physname on the type obstack.
