This adds I2C[0-5] clock support to R8A7791 SoC.
Changes in V2:
* Capitalized ARM in the subject.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When enabling a module clock by clearing its bit in the MSTP control
register, the CPG requires waiting for the status register to signal
that the clock has started. Failure to do so will result in returning
from the clk_enable() call with the clock potentially still disabled,
leading to various race conditions and difficult to debug errors.
Enable status wait for all MSTP clocks on the r8a7790.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When enabling some of the module clocks by clearing stop bits in the
MSTP control registers, the CPG requires waiting for the status
registers to signal that the clocks have started. Failure to do so will
result in returning from the clk_enable() call with the clock
potentially still disabled, leading to various race conditions and
difficult to debug errors.
Enable status wait for all the r8a7779 MSTP clocks that report their
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The armadillo800eva board uses has an SH ethernet controller which uses an
SMSC phy. Select SMSC_PHY for koelsch if SH_ETH is enabled to make use of the
SMSC-specific phy driver rather than relying on the generic phy driver.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The ape6evm board uses has an SMSC911X ethernet controller which uses an
SMSC phy. Select SMSC_PHY for ape6evm if SMSC911X is enabled to make use of the
SMSC-specific phy driver rather than relying on the generic phy driver.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds SATA0 support to Koelsch board.
SATA1 is not available since its pinmux
configuration is fixed to PCIe.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds SATA support to Lager board. Only SATA1 port is available.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au: resolved trivial conflicts]
[horms+renesas@verge.net.au: capitalised "ARM" in subject]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use common clock framework version of clock
drivers/clk/shmobile/clk-emev2.c
instead of sh-clkfwk version
arch/arm/mach-shmobile/clock-emev2.c
when it is configured as a part of multi-platform.
Signed-off-by: Takashi Yoshii <takasi-y@ops.dti.ne.jp>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds VIN1 SoC camera along with ADV7180 subdevice support to Lager.
VIN0 camera is not registered because it has ADV7612 I2C subdevice
which is not supported yet.
Changes in V2:
* made lager_add_vin_device function static.
Changes in V3:
* capitalized ARM in the subject.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds support to run the kernel on the uninitialized KZM9G board, using for
instance the mask ROM boot loader or JTAG. This patch tries to emulate the
style of the corresponding "mackerel" implementation. The DRAM controller
setup code has been adapted from u-boot.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The koelsch board uses has an SH ethernet controller which uses a Micrel
phy. Select MICREL_PHY for koelsch if SH_ETH is enabled to make use of the
Micrel-specific phy driver rather than relying on the generic phy driver.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car sound driver is supporting Mem <-> SRU <-> SSI
transfer via DMAEngine.
The sound will be less noise if it uses SRU path
since it has FIFO.
This patch supports it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car sound driver is supporting Mem <-> SSI
direct transfer via DMAEngine.
Current HPB-DMA is using double plane transfer,
but the sound may have noise since SSI doesn't have FIFO.
This patch supports it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that support for KSZ8041RNLI is added to the Micrel PHY driver and we intend
to support PHY IRQs on the Lager board, we have to enable the Micrel driver.
Do this by selecting CONFIG_MICREL_PHY for Lager if CONFIG_SH_ETH is enabled.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The selection of HAVE_ARM_TWD for OMAP and shmobile depend on LOCAL_TIMER
which no longer exists. They should depend on SMP instead.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch is reducing in size for every release since most board-related
changes have started happening in devicetrees now. Still, we have some things
going on here.
* Renesas platforms are still adding a bit more legacy device support, something
that should trail off shortly as they move to full DT.
* We group most defconfig updates into this branch out of old habits
* Removal of legacy OMAP2 platforms over to DT continues, and a handful of old
code is being removed here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wLdE
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"This branch is reducing in size for every release since most
board-related changes have started happening in devicetrees now.
Still, we have some things going on here.
* Renesas platforms are still adding a bit more legacy device
support, something that should trail off shortly as they move to
full DT
* We group most defconfig updates into this branch out of old habits
* Removal of legacy OMAP2 platforms over to DT continues, and a
handful of old code is being removed here"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: dts: OMAP2: fix interrupt number for rng
ARM: dts: Split omap3 pinmux core device
ARM: dts: Add omap specific pinctrl defines to use padconf addresses
ARM: bcm2835: bcm2835_defconfig updates
ARM: msm_defconfig: Enable restart driver
defconfig: msm_defconfig: Enable CONFIG_ARCH_MSM8974
ARM: msm: Add support for APQ8074 Dragonboard
ARM: exynos_defconfig: Enable S2MPS11 voltage regulator
ARM: tegra: Enable DRM panel support
ARM: shmobile: mackerel: Fix USBHS pinconf entry
ARM: shmobile: Let Koelsch multiplatform boot with Koelsch DTB
ARM: shmobile: Let Lager multiplatform boot with Lager DTB
ARM: shmobile: Remove non-multiplatform Koelsch reference support
ARM: shmobile: Remove non-multiplatform Lager reference support
ARM: shmobile: koelsch-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: lager-reference: Instantiate clkdevs for SCIF and CMT
ARM: shmobile: koelsch-reference: Remove duplicate CCF initialization
ARM: shmobile: lager-reference: Enable multiplaform kernel support
ARM: shmobile: armadillo: Set backlight enable GPIO
ARM: shmobile: Koelsch: add Ether support
...
Conflicts:
arch/arm/mach-omap2/omap_hwmod_2xxx_ipblock_data.c
DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files that
don't require corresponding C changes any more, which is indicating that
the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over to fully
support the platform with DT.
* Renesas platforms continue their conversion over from legacy platform devices
to DT-based for hardware description.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4o2d
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT and DT-conversion-related changes for various ARM platforms. Most
of these are to enable various devices on various boards, etc, and not
necessarily worth enumerating.
New boards and systems continue to come in as new devicetree files
that don't require corresponding C changes any more, which is
indicating that the system is starting to work fairly well.
A few things worth pointing out:
* ST Ericsson ux500 platforms have made the major push to move over
to fully support the platform with DT
* Renesas platforms continue their conversion over from legacy
platform devices to DT-based for hardware description"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (327 commits)
ARM: dts: SiRF: add pin group for USP0 with only RX or TX frame sync
ARM: dts: SiRF: add lost usp1_uart_nostreamctrl pin group for atlas6
ARM: dts: sirf: add lost minigpsrtc device node
ARM: dts: sirf: add clock, frequence-voltage table for CPU0
ARM: dts: sirf: add lost bus_width, clock and status for sdhci
ARM: dts: sirf: add lost clocks for cphifbg
ARM: dts: socfpga: add pl330 clock
ARM: dts: socfpga: update L2 tag and data latency
arm: sun7i: cubietruck: Enable the i2c controllers
ARM: dts: add support for EXYNOS4412 based TINY4412 board
ARM: dts: Add initial support for Arndale Octa board
ARM: bcm2835: add USB controller to device tree
ARM: dts: MSM8974: Add MMIO architected timer node
ARM: dts: MSM8974: Add restart node
ARM: dts: sun7i: external clock outputs
ARM: dts: sun7i: Change 32768 Hz oscillator node name to clk@N style
ARM: dts: sun7i: Add pin muxing options for clock outputs
ARM: dts: sun7i: Add rtp controller node
ARM: dts: sun5i: Add rtp controller node
ARM: dts: sun4i: Add rtp controller node
...
New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with some
random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m, i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pgLW
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New core SoC-specific changes.
New platforms:
* Introduction of a vendor, Hisilicon, and one of their SoCs with
some random numerical product name.
* Introduction of EFM32, embedded platform from Silicon Labs (ARMv7m,
i.e. !MMU).
* Marvell Berlin series of SoCs, which include the one in Chromecast.
* MOXA platform support, ARM9-based platform used mostly in
industrial products
* Support for Freescale's i.MX50 SoC.
Other work:
* Renesas work for new platforms and drivers, and conversion over to
more multiplatform-friendly device registration schemes.
* SMP support for Allwinner sunxi platforms.
* ... plus a bunch of other stuff across various platforms"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (201 commits)
ARM: tegra: fix tegra_powergate_sequence_power_up() inline
ARM: msm_defconfig: Update for multi-platform
ARM: msm: Move MSM's DT based hardware to multi-platform support
ARM: msm: Only build timer.c if required
ARM: msm: Only build clock.c on proc_comm based platforms
ARM: ux500: Enable system suspend with WFI support
ARM: ux500: turn on PRINTK_TIME in u8500_defconfig
ARM: shmobile: r8a7790: Fix I2C controller names
ARM: msm: Simplify ARCH_MSM_DT config
ARM: msm: Add support for MSM8974 SoC
ARM: sunxi: select ARM_PSCI
MAINTAINERS: Update Allwinner sunXi maintainer files
ARM: sunxi: Select RESET_CONTROLLER
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJS4Vf7AAoJEIwa5zzehBx3f9UP/jwMlbfbSZHfNQ/QG0SqZ9RD
zvddyDMHY/qXnzgF3Dax+JR9BDDVy8AlQe713FCoiHJZggWRAbbavkx8gxITDrZQ
6NYaEkkuVxqyM8APl3PwMqYm8UZ8MUf4lCltlOA4jkesY9vue91AFnfyKh2CvHrn
Leg4XT6mFzf/vYDL6RbvTz/Qr253uv3KvYBxkeiRNa0Y7OXRemEXSOfgxh0YGxUl
LZ2IWQFOh/DH4kaeQI8V4G67X3ceHiFyhCnl0CPwfxaZaNBVaxvIFgIUTdetS6Sb
zcXa029tE/Dfsr55vZAv9LUHEipCSOeE5rn2EJWehTWyM7vJ42Eozqgh+zfCjXS7
Ib6g2npsvIluQit/RdITu44h5yZlrQsLgKTGJ8jjXqbT4HQ/746W8b/TP0YLtbw7
N8oqr7k4vsZyF0dAYZQtfQUZeGISz67UbFcdzl9tmYOR7HFuAYkAQYst77zkVJf8
om59BAYYTG5FNjQ4I9AKUfJzxXYveI6AKpXSCCZiahpFM2D1CJIzp9Wi0GwK1HRR
sFVWhS0dajvz63pVVC2tw5Sq4J7onRRNGIXFPoE5fkmlelm0/q0zzGjw3Z0nTqbZ
8zxuwuy2FfPJK11GbUAIhAgn1sCLYyAhl6IE+FsanGeMOSGIMrH0v5/HphAxoCXt
BvqMDogyLoGPce1Gm3pJ
=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
This fixes the issue introduced by the following commit:
b448c904f5 "ARM: shmobile: r8a7790: add I2C support"
The R8A7790 is an R-Car Gen2 SoC. The clock division factor
(CDF) width is 3 bits on Gen2 as opposed to 2 bits on Gen1.
Fix the device names for R8A7790 SoC to make the R-Car I2C
driver configure the hardware properly.
Changes in V2:
* rebased on top of the latest branch;
* capitalized ARM in the subject line;
* noted the commit that caused the issue in the log.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Global
- Kconfig: Mention Renesas ARM SoCs instead of SH-Mobile
* r7s72100 SoC (RZ/A1H) based Genmai Board
- Add Multiplatform support
- Add Reference DT
* r8a7791 (R-Car M2) based Koelsch board
- Add pinctrl_register_mappings() for Koelsch
- Hook up SW30-SW36 on Koelsch
- Mark GPIO keys as wake-up sources
- Use ->init_late()
- Add Multiplatform support
- Set .debounce_interval for GPIO keys
- Add SW2 to GPIO keys
- Add Led 6, 7 and 8 support
- Add reference DT
- Enable PFC/GPIO
* r8a7790 (R-Car H2) based Lager board
- Add gpio/fixed regulator for SDHI
- Add SPI FLASH support on QSPI
- Mark GPIO keys as wake-up sources
- Use ->init_late()
- Set .debounce_interval for GPIO keys
* r8a7778 (R-Car M1) based Bock-W board
- bockw: remove unused RSND_SSI_CLK_FROM_ADG
- Set .debounce_interval for GPIO keys
- Correct FPGA ioremap area
- Use regulator for MMCIF
* r8a7740 (R-Mobile A1) based Armadillo board
- Correct FSI address size
* sh7374 (SH-Mobile AP4) based Mackerel board
- Use pinconf API to configure pin pull-down
- clk_round_rate() can return a zero to indicate an error
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=5zhn
-----END PGP SIGNATURE-----
Merge tag 'renesas-boards-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards
From Simon Horman:
Renesas ARM based SoC board updates for v3.14
* Global
- Kconfig: Mention Renesas ARM SoCs instead of SH-Mobile
* r7s72100 SoC (RZ/A1H) based Genmai Board
- Add Multiplatform support
- Add Reference DT
* r8a7791 (R-Car M2) based Koelsch board
- Add pinctrl_register_mappings() for Koelsch
- Hook up SW30-SW36 on Koelsch
- Mark GPIO keys as wake-up sources
- Use ->init_late()
- Add Multiplatform support
- Set .debounce_interval for GPIO keys
- Add SW2 to GPIO keys
- Add Led 6, 7 and 8 support
- Add reference DT
- Enable PFC/GPIO
* r8a7790 (R-Car H2) based Lager board
- Add gpio/fixed regulator for SDHI
- Add SPI FLASH support on QSPI
- Mark GPIO keys as wake-up sources
- Use ->init_late()
- Set .debounce_interval for GPIO keys
* r8a7778 (R-Car M1) based Bock-W board
- bockw: remove unused RSND_SSI_CLK_FROM_ADG
- Set .debounce_interval for GPIO keys
- Correct FPGA ioremap area
- Use regulator for MMCIF
* r8a7740 (R-Mobile A1) based Armadillo board
- Correct FSI address size
* sh7374 (SH-Mobile AP4) based Mackerel board
- Use pinconf API to configure pin pull-down
- clk_round_rate() can return a zero to indicate an error
* tag 'renesas-boards-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (75 commits)
ARM: shmobile: lager: add gpio/fixed regulator for SDHI
ARM: shmobile: bockw: remove unused RSND_SSI_CLK_FROM_ADG
ARM: shmobile: armadillo: fixup FSI address size
ARM: Kconfig: Mention Renesas ARM SoCs instead of SH-Mobile
ARM: shmobile: mackerel: Use pinconf API to configure pin pull-down
ARM: shmobile: Lager:add SPI FLASH support on QSPI
ARM: shmobile: mackerel: clk_round_rate() can return a zero to indicate an error
ARM: shmobile: Add pinctrl_register_mappings() for Koelsch
ARM: shmobile: Use ->init_late() on Lager
ARM: shmobile: Hook up SW30-SW36 on Koelsch
ARM: shmobile: koelsch: mark GPIO keys as wake-up sources
ARM: shmobile: Use ->init_late() on Koelsch
ARM: shmobile: lager: mark GPIO keys as wake-up sources
ARM: shmobile: r7s72100 Genmai Multiplatform
ARM: shmobile: r7s72100 Genmai DT reference C bits
ARM: shmobile: r7s72100 Genmai DT reference DTS bits
ARM: shmobile: Initial r8a7791 and Koelsch multiplatform support
ARM: shmobile: koelsch: set .debounce_interval
ARM: shmobile: lager: set .debounce_interval
ARM: shmobile: bockw: add pin pull-up setting for SDHI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 4dcfa60071 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 4dcfa60071 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 4dcfa60071 ("ARM: DMA-API: better
handing of DMA masks for coherent allocations") added an additional
check to the coherent DMA mask that results in an error when the mask is
larger than what dma_addr_t can address.
Set the LCDC coherent DMA mask to DMA_BIT_MASK(32) instead of ~0 to fix
the problem.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested with RIIC2 on a genmai board. Others untested but hopefully
trivial enough to be added.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field will be removed from the sh-sci driver. Don't set it and let
the driver handle baud rate calculation internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Passing the register base address and IRQ through platform data is
deprecated. Use resources instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SCIF driver is transitioning to platform resources. Board code will
thus need to define an array of resources for each SCIF device. This is
incompatible with the macro-based SCIF platform data definition as an
array. Rework the macro to define platform data as individual
structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SCIF driver is transitioning to platform resources. Board code will
thus need to define an array of resources for each SCIF device. This is
incompatible with the macro-based SCIF platform data definition as an
array. Rework the macro to define platform data as individual
structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SCIF driver is transitioning to platform resources. Board code will
thus need to define an array of resources for each SCIF device. This is
incompatible with the macro-based SCIF platform data definition as an
array. Rework the macro to define platform data as individual
structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SCIF driver is transitioning to platform resources. Board code will
thus need to define an array of resources for each SCIF device. This is
incompatible with the macro-based SCIF platform data definition as an
array. Rework the macro to define platform data as individual
structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SCIF driver is transitioning to platform resources. Board code will
thus need to define an array of resources for each SCIF device. This is
incompatible with the macro-based SCIF platform data definition as an
array. Rework the macro to define platform data as individual
structures.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace copy-n-paste SCIF platform data and device declaration with a
macro. This reduces the amount of code and improves readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace copy-n-paste SCIF platform data and device declaration with a
macro. This reduces the amount of code and improves readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace copy-n-paste SCIF platform data and device declaration with a
macro. This reduces the amount of code and improves readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Replace copy-n-paste SCIF platform data and device declaration with a
macro. This reduces the amount of code and improves readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is needed to use SRC (= Sampling Rate Converter)
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Global
- Use interrupt macros
- Use #include in device tree sources
- Tidyup DT node naming
* emev2 (Emma Mobile EV2) SoC
- Setup internal peripheral interrupts as level high
- Use interrupt macros in DT files
- Add clock tree description in DT
* r8a7791 (R-Car M2) SoC
- Correct GPIO resources
* r8a7791 (R-Car M2) based Koelsch board
- Configure PFC and GPO
- Use r8a7791 suffix for IRQC compat string
- Add DT reference
* r8a7790 (R-Car H2) based Lager board
- Include all 4 GiB of memory
- Use r8a7790 suffix for IRQC and MMCIF compat strings
- Enable MMCIF
- Add default PFC settings
* r8a7778 (R-Car M1) SoC
- Suffix for INTC compat string
- Add HSPI, MMCIF, SDHI and I2C suppport on DTSI
- Correct pin control device addresses
* r8a7778 (R-Car M1) based Bock-W board
- Use falling edge IRQ for LAN9221 in DT reference
- Enable I2C, HSPI0, MMCIF and SDHI
- Correct MMC pin conflict
- Remove manual PFC settings from DT reference
- Add default PFC settings
* r8a7779 (R-Car H1) SoC
- Add HSPI and SDHI support
- Suffix for INTC compat string
* r8a7779 (R-Car H1) based Marzen board
- Enable HSPI0 and SDHI in DTS
- Remove SDHI0 WP pin setting
- Use falling edge IRQ for LAN9221 in DT reference
- Add SDHI support
* r8a7740 (R-Mobile A1) SoC
- Suffix for INTC compat string
- Add FSI support via DTSI
- Use interrupt macros
* r8a7740 based Armadillo board
- Add FSI support for DTS
- Use low level IRQ for ST1231 in DT reference
* r8a73a4 (SH-Mobile APE6) SoC
- Use interrupt macros in DT files
* r8a73a4 (R-Mobile APE6) based ape6evm board
- Include all 2 GiB of memory
* r8a73a0 (SH-Mobile AG5) SoC
- Correct SDHI compat string
* r8a73a0 (SH-Mobile AG5) based kzm9d board
- Add GPIO keys and Add PCF8575 GPIO extender to DT
- Enable DSW2 with gpio-keys
- Use falling edge IRQ for LAN9221 in DT reference
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSqm6XAAoJENfPZGlqN0++pOoQAIgdo3M/CCP56+wAop/nYOfx
DDdozpEt+V6RcNytVwGEkQboIDMqnekiAvhLiJ7GHT7sMHmf7au2KFkNPpxN+noU
QVgmJaMsi2AoaoV6T+rc0ice7sve+3gbHE0S49frNVlabNlo69y5Y3prYBzLmfdt
hefvngIUx6vhosaH00elYhsRTSTd1i5Pkj+jAYQNil1sI+QBJKC61buZrlLPMOfh
WBMZXKROSN+jIYsqwmz+O7LvqNZa+Wjm9M8NFQnKWkv4fj9on+RZtkLuNo62Yy2P
AaOM5Z0B2q5q35a7QcsLX23QiHOtkGOXIXehzjakzA56L5kUaZMWdfSUWGXPE+DU
B163SndwQhRPiYFrb8//Ri5+GQxls6Pw6UKtT7owDMmqkqsYUrJHm7zfu88RcX1O
UcDrtd3ZlF4XMmr3iNxIRzscFx8faQbIErfG2VornRRkEKLT+ILRvcAedZxkhGLk
6fs8efTcxR7lvY+7pDtJ1N/xyGGykSnsf0LiCp5BkADamSyhGhqUcr8CjUfjMhKD
r7WhzbHEQ7FdQ7B4Y8QmxKyH9dC1wNPxB8kZ4m6YjEKFYC95XCehMQhWvbUsx9vM
jBrvvG7414+t3M2CmROwrs9NujJ0Kf0i6078Hvi06l+w4XYe55ytLUGMnXsJAuCL
B7aAaVRIAt3UYK7tncK+
=jkNE
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Renesas ARM based SoC DT updates for v3.14
* Global
- Use interrupt macros
- Use #include in device tree sources
- Tidyup DT node naming
* emev2 (Emma Mobile EV2) SoC
- Setup internal peripheral interrupts as level high
- Use interrupt macros in DT files
- Add clock tree description in DT
* r8a7791 (R-Car M2) SoC
- Correct GPIO resources
* r8a7791 (R-Car M2) based Koelsch board
- Configure PFC and GPO
- Use r8a7791 suffix for IRQC compat string
- Add DT reference
* r8a7790 (R-Car H2) based Lager board
- Include all 4 GiB of memory
- Use r8a7790 suffix for IRQC and MMCIF compat strings
- Enable MMCIF
- Add default PFC settings
* r8a7778 (R-Car M1) SoC
- Suffix for INTC compat string
- Add HSPI, MMCIF, SDHI and I2C suppport on DTSI
- Correct pin control device addresses
* r8a7778 (R-Car M1) based Bock-W board
- Use falling edge IRQ for LAN9221 in DT reference
- Enable I2C, HSPI0, MMCIF and SDHI
- Correct MMC pin conflict
- Remove manual PFC settings from DT reference
- Add default PFC settings
* r8a7779 (R-Car H1) SoC
- Add HSPI and SDHI support
- Suffix for INTC compat string
* r8a7779 (R-Car H1) based Marzen board
- Enable HSPI0 and SDHI in DTS
- Remove SDHI0 WP pin setting
- Use falling edge IRQ for LAN9221 in DT reference
- Add SDHI support
* r8a7740 (R-Mobile A1) SoC
- Suffix for INTC compat string
- Add FSI support via DTSI
- Use interrupt macros
* r8a7740 based Armadillo board
- Add FSI support for DTS
- Use low level IRQ for ST1231 in DT reference
* r8a73a4 (SH-Mobile APE6) SoC
- Use interrupt macros in DT files
* r8a73a4 (R-Mobile APE6) based ape6evm board
- Include all 2 GiB of memory
* r8a73a0 (SH-Mobile AG5) SoC
- Correct SDHI compat string
* r8a73a0 (SH-Mobile AG5) based kzm9d board
- Add GPIO keys and Add PCF8575 GPIO extender to DT
- Enable DSW2 with gpio-keys
- Use falling edge IRQ for LAN9221 in DT reference
* tag 'renesas-dt-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (102 commits)
ARM: shmobile: marzen: enable HSPI0 in DTS
ARM: shmobile: r8a7779: add HSPI support to DTSI
ARM: shmobile: Use r8a7779 suffix for INTC compat string
ARM: shmobile: Use r8a7778 suffix for INTC compat string
ARM: shmobile: Use r8a7740 suffix for INTC compat string
ARM: shmobile: Use sh73a0 suffix for INTC compat string
ARM: shmobile: armadillo: add FSI support for DTS
ARM: shmobile: r8a7740: add FSI support via DTSI
ARM: shmobile: emev2: Setup internal peripheral interrupts as level high
ARM: shmobile: emev2: Use interrupt macros in DT files
ARM: shmobile: Use interrupt macros in r8a73a4 and r8a7778 DT files
ARM: shmobile: Fix r8a7791 GPIO resources in DTS
ARM: shmobile: Include all 4 GiB of memory on Lager DT Ref
ARM: shmobile: Include all 4 GiB of memory on Lager
ARM: shmobile: Include all 2 GiB of memory on APE6EVM
ARM: shmobile: Include all 2 GiB of memory on APE6EVM DT Ref
ARM: shmobile: kzm9g-reference: Add GPIO keys to DT
ARM: shmobile: kzm9g-reference: Add PCF8575 GPIO extender to DT
ARM: shmobile: Koelsch DT reference GPIO LED support
ARM: shmobile: Enable DSW2 with gpio-keys on KZM9D
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
While <mach/timex.h> isn't used for multi-platform builds since long it
still is for "normal" builds. As the previous patches fix all sites to
not make use of this per-platform file, it can go now for good also for
platforms that are not (yet) converted to multi-platform.
While at it there are no users of CLOCK_TICK_RATE any more, so also drop
the dummy #define.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fix a typo in the USBHS1 pinconf entry that prevented the pull-down from
being enabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Let the multiplatform Koelsch support boot with the legacy DTS for
Koelsch as well as the Koelsch reference DTS.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Let the multiplatform Lager support boot with the legacy DTS for Lager
as well as the Lager reference DTS.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that r8a7791 has CCF support remove the legacy Koelsch reference
Kconfig bits CONFIG_MACH_KOELSCH_REFERENCE for the non-multiplatform
case.
Starting from this commit Koelsch board support is always enabled via
CONFIG_MACH_KOELSCH, and CONFIG_ARCH_MULTIPLATFORM is used to select
between board-koelsch.c and board-koelsch-reference.c
The file board-koelsch-reference.c can no longer be used together with
the legacy sh-clk clock framework, instead CCF is used.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: Dropped arch/arm/boot/dts/Makefile portion]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that r8a7790 has CCF support remove the legacy Lager reference
Kconfig bits CONFIG_MACH_LAGER_REFERENCE for the non-multiplatform
case.
Starting from this commit Lager board support is always enabled via
CONFIG_MACH_LAGER, and CONFIG_ARCH_MULTIPLATFORM is used to select
between board-lager.c and board-lager-reference.c
The file board-lager-reference.c can no longer be used together with
the legacy sh-clk clock framework, instead CCF is used.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the common clock framework is supported, the clock lookup
entries in clock-r8a7791.c are not registered anymore. Devices must
instead reference their clocks in the device tree. However, SCIF and CMT
devices are still instantiated through platform code, and thus need a
clock lookup entry.
Retrieve the SCIF and CMT clock entries by name and register clkdevs for
the corresponding devices. This will be removed when the SCIF and CMT
devices will be instantiated from the device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the common clock framework is supported, the clock lookup
entries in clock-r8a7790.c are not registered anymore. Devices must
instead reference their clocks in the device tree. However, SCIF and CMT
devices are still instantiated through platform code, and thus need a
clock lookup entry.
Retrieve the SCIF and CMT clock entries by name and register clkdevs for
the corresponding devices. This will be removed when the SCIF and CMT
devices will be instantiated from the device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The common clock framework is initialized in the rcar_gen2_init_timer()
function, remove the of_clk_init() call.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable multiplaform ARM architecture support for the Lager reference
board. Common clock framework initialization will be handled by the
rcar_gen2_init_timer() call, we just need to remove the legacy clock
code initialization.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Armadillo 800 EVA panel module has a backlight enable signal
connected to GPIO 61. Instead of requesting the GPIO in board code and
setting it to a high level unconditionally, pass the GPIO number to the
PWM backlight driver as the backlight enable GPIO.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Register Ether platform device and pin data on the Koelsch board.
Register platform fixup for Micrel KSZ8041 PHY, just like on the Lager board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Only the LVDS output is currently supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
4dcfa60071
(ARM: DMA-API: better handing of DMA masks for coherent allocations)
exchanged DMA mask check method.
Below warning will appear without this patch
asoc-simple-card asoc-simple-card.0: \
Coherent DMA mask 0xffffffffffffffff is larger than dma_addr_t allows
asoc-simple-card asoc-simple-card.0: \
Driver did not use or check the return value from dma_set_coherent_mask()?
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The koelsch board uses has an SH ethernet controller which uses a Micrel
phy. Select MICREL_PHY for koelsch if SH_ETH is enabled to make use of the
Micrel-specific phy driver rather than relying on the generic phy driver.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When CONFIG_COMMON_CLOCK is enabled, call rcar_gen2_clocks_init() in the
timer init function to initialize the common clock framework before
initializing the clock sources. This will take care of clock
initialization when the r8a779[01] boards will be switched to
multiplatform kernels.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 22ceeee16e ("pwm-backlight: Add
power supply support") added a mandatory power supply for the PWM
backlight. Add a fixed 5V regulator to board code with a consumer supply
entry for the backlight device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit ad11cb9a5cf96346f1240995c672cdbb5501785c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PCI sub-system is not enabled by default on ARM and on certain
Renesas devices the build does not select it. This means that there
are configurations that do not allow the AHB-PCI bridge used for the
USB sub-systems to be built.
For the R8A7790, R8A7791 and EMEV-2 select MIGHT_HAVE_PCI to allow the
PCI drivers to be built. Also select MIGHT_HAVE_PCI for the multi-config
where there may be many Reneasas devices selected.
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
HPB-DMAC has 2 channel for USB Func (= D0/D1)
D0 is used as Tx, D1 is used as Rx on this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
If the system has been started in non-secure mode, then the ARM generic
timer is not configurable during the kernel initialisation. Currently
the only thing we can check for is if the timer has been correctly
configured during the boot process.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Ian Molton <ian.molton@codethink.co.uk>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
8e0e7aaef3
(ARM: shmobile: Drop r8a7779_add_device_to_domain())
removed last user of struct platform_device on this header.
It is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for R8A7791 Ether clock.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
<linux/platform_data/camera-rcar.h> is needed on BockW,
not setup-r8a7778.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
WP pin is not implemented on Marzen
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to ePAPR spec,
this patch tidies up DT node name and related clock.
This patch also adds missing SDHI2 entry
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Current Bock-W reference is calling PFC initializer manually,
but now, it can use DTS PFC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fixed regulator is used for SDHI0/2 Vcc.
We should use da9063 driver for Vccq,
but, it doesn't have regulator support at this point.
This patch uses gpio-regulator for it as quick-hack.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
92eba04e4b
(ASoC: rcar: remove RSND_SSI_CLK_FROM_ADG) removed
RSND_SSI_CLK_FROM_ADG, it is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
FSI address size is 0x400, not 0x8400
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Only the SH-Mobile product name is mentioned in the Kconfig descriptions
and help texts. This makes it difficult for external engineers working
on other Renesas platforms to find upstream platform support as the
combination of the SH-Mobile name and using the product number proved an
effective method of concealment.
Replace the "SH-Mobile" name with "Renesas ARM SoCs" in all the related
descriptions, help texts and comments.
Reported-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The USB0 and USB1 VBUS pins must be pulled down. Add corresponding
configuration entries in the pinctrl map table instead of manually
poking the pin control registers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables Spansion S25FL512SAGMFIG11 chip on QSPI,
Add support for the QSPI interface on Lager.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Treat both negative and zero return values from clk_round_rate() as
errors. This is needed since subsequent patches will convert
clk_round_rate()'s return value to be an unsigned type, rather than a
signed type, since some clock sources can generate rates higher than
(2^31)-1 Hz.
Eventually, when calling clk_round_rate(), only a return value of zero
will be considered a error. All other values will be considered valid
rates. The comparison against values less than 0 is kept to preserve
the correct behavior in the meantime.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add code to setup the r8a7791 PFC for the Koelsch board.
At this point serial consoles are added, and in the near
future other platform-device-only devices will be added
here like for instance the r8a7791 DU.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook in shmobile_init_late() on Lager V2. This enables some PM
related things like CPUIdle and Suspend-to-RAM.
With this patch applied it is possible to use Suspend-to-RAM:
# echo enabled > /sys/class/tty/ttySC6/power/wakeup
# echo mem > /sys/power/state
(wake by sending a character on the serial console)
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for Koelsch SW30-SW36 using GPIO keys.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable wakeup for the GPIO keys on the Koelsch board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook in shmobile_init_late() on Koelsch. This enables some PM
related things like CPUIdle and Suspend-to-RAM.
With this patch applied it is possible to use Suspend-to-RAM:
# echo enabled > /sys/class/tty/ttySC6/power/wakeup
# echo mem > /sys/power/state
(wake by sending a character on the serial console)
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable wakeup for the GPIO keys on the Lager board.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add C code support for r7s72100 Genmai DT reference.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Koelsch and r8a7791 to CONFIG_SHMOBILE_MULTI. At this
point CCF is not yet supported so you cannot run this code
yet. For CCF support to happen several different components
are needed, and this is one simple portion that moves us
forward. Other patches need to build on top of this one.
Koelsch board support exists in 3 flavors:
1) SHMOBILE_MULTI, MACH_KOELSCH - board-koelsch-reference.c (CCF + DT)
2) SHMOBILE, MACH_KOELSCH_REFERENCE - board-koelsch-reference.c (DT)
3) SHMOBILE, MACH_KOELSCH - board-koelsch.c (legacy C code)
When CCF is done then 2) will be removed. When 1) includes same features
as 3) then 3) will be removed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In R-Car GPIO hardware block, 'chattering removal' feature can be
enabled on GPIO-n-[3:0] pins, but it's not supported on rest of pins
GPIO-n-[31:4].
Set an appropriate debounce interval, instead. We could confirm that
spurious/unnecessary GPIO interrupts are prevented by this settings.
Based on work for the lager board by Shinya Kuribayashi.
Cc: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
In R-Car GPIO hardware block, 'chattering removal' feature can be
enabled on GPIO-n-[3:0] pins, but it's not supported on rest of pins
GPIO-n-[31:4].
Set an appropriate debounce interval, instead. We could confirm that
spurious/unnecessary GPIO interrupts are prevented by this settings.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT reference support for the r8a7791 Koelsch board.
This board support file will be used together with common
clocks and multiplatform in the future.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable Koelsch GPIO switch for GPIO input and IRQ testing purpose.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable r8a7791 PFC and GPIO on the Koelsch board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
When regulators are used with MMC devices, sh_mmcif_plat_data::ocr
is not needed, they can be removed from platform data.
This patch adds v3.3 regulator settings,
and moved fixed-dummy regulator registration position
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Tidy up clock table order for r7s72100, r8a7779, r8a7779, r8a7790,
sh7372 and sh73a0 SoCs.
* Tidy up camera-rcar header for r8a7779 SoC
* Tidy up registration of VIN on r8a7779 SoC
* Tidy up PFC registration on r8a7790 SoC
* Correct typo in clocks for r8a7790 SoC
* Don't use named resources for IPMMU, I2C and TMU on sh73a0 SoC
* Don't use named resources for MMCIF and SDHI on ape6evm board
* Don't use named resources for MMCIF on lager board
* Tidy up device registration on lager board
* Tidy up headers for bockw board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=v12l
-----END PGP SIGNATURE-----
Merge tag 'renesas-cleanup-for-v3.14' into boards-base
Renesas ARM based SoC cleanups for v3.14
* Tidy up clock table order for r7s72100, r8a7779, r8a7779, r8a7790,
sh7372 and sh73a0 SoCs.
* Tidy up camera-rcar header for r8a7779 SoC
* Tidy up registration of VIN on r8a7779 SoC
* Tidy up PFC registration on r8a7790 SoC
* Correct typo in clocks for r8a7790 SoC
* Don't use named resources for IPMMU, I2C and TMU on sh73a0 SoC
* Don't use named resources for MMCIF and SDHI on ape6evm board
* Don't use named resources for MMCIF on lager board
* Tidy up device registration on lager board
* Tidy up headers for bockw board
Based on work for the r8a7778 SoC by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since ("ARM: shmobile: Remove legacy KZM9D board code")
It is now necessary for AUTO_ZRELADDR to be selected
in order for the kernel to build with kzm9d_defconfig.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SuperH lookups clock is using CLKDEV_CON/DEV/ICK_ID() macro
for a long term.
But in these days, the ICK clock is defined in random place.
This patch arranges it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
I2C clock is based on P clock, not HP clock
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the r8a7791 thermal device as legacy clocks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a thermal platform device for the legacy case
on the r8a7791 SoC. This keeps the r8a7791 in sync
with the r8a7790 sister device.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the r8a7790 DT thermal device to the legacy clocks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SH-Mobile platforms are transitioning from non-multiplatform to
multiplatform kernel. A new ARCH_SHMOBILE_MULTI configuration symbol has
been created to group all multiplatform-enabled SH-Mobile SoCs. The
existing ARCH_SHMOBILE configuration symbol groups SoCs that haven't
been converted yet.
This arrangement works fine for the arch/ code, but lots of drivers
needed on both ARCH_SHMOBILE and ARCH_SHMOBILE_MULTI depend on
ARCH_SHMOBILE only. In order to avoid changing them, rename
ARCH_SHMOBILE to ARCH_SHMOBILE_LEGACY, and create a new boolean
ARCH_SHMOBILE configuration symbol that is selected by both
ARCH_SHMOBILE_LEGACY and ARCH_SHMOBILE_MULTI.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The ZX parent clock isn't implemented yet, add it as well.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when the legacy KZM9D board code is gone, make sure
USE_OF is selected in case of the EMEV2 SoC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when KZM9D legacy C board support code is
gone then remove emev2_add_standard_devices()
and all the platform devices from setup-emev2.c.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the C and platform device version of KZM9D.
The DT version of KZM9D board support can now instead
directly be used with SoC specific code in setup-emev2.c.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Hook up shmobile_init_late() to enable various
code such as suspend-to-RAM and CPUIdle.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a SoC specific function that initializes
clocks and starts DT probing in case of EMEV2.
This EMEV2 SoC support code may be built for
either legacy SHMOBILE or SMOBILE_MULTI.
The change allows us to support existing board
specific KZM9D DTB with these SoC specific
DT_MACHINE_START() callbacks.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds support for QSPI on the r8a7790.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r7s72100 contains GPIO controllers so make sure the GPIO
subsystem can be built by selecting ARCH_WANT_OPTIONAL_GPIOLIB.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add GPIO controller platform devices for the r8a7791 SoC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a platform device for the r8a7791 PFC device.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7791 contains IRQC hardware so make sure
the driver gets built by selecting RENESAS_IRQC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
10e8d4f6dd
(ARM: mach-shmobile: r8a7779: Minimal setup using DT)
added I2C driver for DT, but it didn't add clock.
This patch adds missing clock for I2C
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Do not build the phy fixup unless CONFIG_PHYLIB is enabled.
Other than not being useful it is also not possible to link
the code under this condition as phy_register_fixup_for_id(),
mdiobus_read() and mdiobus_write() are absent.
arch/arm/mach-shmobile/built-in.o: In function `lager_ksz8041_fixup':
board-lager.c:(.text+0xb8): undefined reference to `mdiobus_read'
board-lager.c:(.text+0xd4): undefined reference to `mdiobus_write'
arch/arm/mach-shmobile/built-in.o: In function `lager_init':
board-lager.c:(.init.text+0xafc): undefined reference to `phy_register_fixup_for_id'
This problem was introduced by 48c8b96f21
("ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup")
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SuperH lookups clock is using CLKDEV_CON/DEV/ICK_ID() macro
for a long term.
But in these days, the ICK clock is defined in random place.
This patch arranges it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SuperH lookups clock is using CLKDEV_CON/DEV/ICK_ID() macro
for a long term.
But in these days, the ICK clock is defined in random place.
This patch arranges it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SuperH lookups clock is using CLKDEV_CON/DEV/ICK_ID() macro
for a long term.
But in these days, the ICK clock is defined in random place.
This patch arranges it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
sh_eth driver which needs platform data at the time of
registration is not used.
Now, ARM/shmobile aims to support DT,
and the C code base board support will be removed
if DT support is completed.
Current driver registration method which needs platform data
and which is not shared complicates codes.
This means legacy C code cleanup after DT supporting
will be more complicated
This patch removes r8a7779_add_ether_device()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This is the r8a7790 SoC not the r8a77a4 SoC and
clocks are updated in r8a7790_clock_init not r8a73a4_clock_init.
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
<linux/platform_data/camera-rcar.h> is needed on Marzen,
not setup-r8a7779.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Break out the r8a7790 PFC platform device creation code
to increase readability and follow same style as r8a7791.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Clean up the Lager DT reference board code to make it match
Koelsch DT reference including using the rcar-gen2 header.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
VIN driver which needs platform data at the time of
registration is used from Marzen only.
Now, ARM/shmobile aims to support DT,
and the C code base board support will be removed
if DT support is completed.
Current driver registration method which needs platform data
and which is not shared complicates codes.
This means legacy C code cleanup after DT supporting
will be more complicated
This patch registers it on board code as cleanup C code
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
linux/pinctrl/machine.h is no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Mostly bug fixes and clean up. There is a new driver, which is actually
moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree support
in the pwm-backlight driver. Backlights can now additionally be powered
using a regulator and enabled using a GPIO in addition to just the PWM
input.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=CB+z
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Mostly bug fixes and clean up. There is a new driver, which is
actually moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree
support in the pwm-backlight driver. Backlights can now additionally
be powered using a regulator and enabled using a GPIO in addition to
just the PWM input"
* tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
Documentation/pwm: Update supported SoC name for pwm-samsung
pwm: samsung: Fix kernel warning while unexporting a channel
MAINTAINERS: Move PWM subsystem tree to kernel.org
Documentation/pwm: Fix trivial typos
pwm-backlight: Remove unused variable
pwm_backlight: avoid short blank screen while doing hibernation
pwm-backlight: Fix brightness adjustment
pwm: add ep93xx PWM support
pwm-backlight: Allow for non-increasing brightness levels
pwm-backlight: Add power supply support
pwm-backlight: Use new enable_gpio field
unicore32: Initialize PWM backlight enable_gpio field
ARM: shmobile: Initialize PWM backlight enable_gpio field
ARM: SAMSUNG: Initialize PWM backlight enable_gpio field
ARM: pxa: Initialize PWM backlight enable_gpio field
ARM: OMAP: Initialize PWM backlight enable_gpio field
pwm-backlight: Add optional enable GPIO
pwm-backlight: Track enable state
pwm-backlight: Refactor backlight power on/off
pwm-backlight: Improve readability
...
Board-related updates. This branch is getting smaller and smaller, which is
the whole idea so that's reassuring.
Right now by far most of the code is related to shmobile updates, and
they are now switching over to removal of board code and migration to
multiplatform, so we'll see their board code base shrink in the near
future too, I hope.
In addition to that is some defconfig updates, some display updates for OMAP
and a bit of new board support for Rockchip boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZYOa
-----END PGP SIGNATURE-----
Merge tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC board updates from Olof Johansson:
"Board-related updates. This branch is getting smaller and smaller,
which is the whole idea so that's reassuring.
Right now by far most of the code is related to shmobile updates, and
they are now switching over to removal of board code and migration to
multiplatform, so we'll see their board code base shrink in the near
future too, I hope.
In addition to that is some defconfig updates, some display updates
for OMAP and a bit of new board support for Rockchip boards"
* tag 'boards-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (56 commits)
ARM: rockchip: add support for rk3188 and Radxa Rock board
ARM: rockchip: add dts for bqcurie2 tablet
ARM: rockchip: enable arm-global-timer
ARM: rockchip: move shared dt properties to common source file
ARM: OMAP2+: display: Create omap_vout device inside omap_display_init
ARM: OMAP2+: display: Create omapvrfb and omapfb devices inside omap_display_init
ARM: OMAP2+: display: Create omapdrm device inside omap_display_init
ARM: OMAP2+: drm: Don't build device for DMM
ARM: tegra: defconfig updates
RX-51: Add support for OMAP3 ROM Random Number Generator
ARM: OMAP3: RX-51: ARM errata 430973 workaround
ARM: OMAP3: Add secure function omap_smc3() which calling instruction smc #1
ARM: shmobile: marzen: enable INTC IRQ
ARM: shmobile: bockw: add SMSC support on reference
ARM: shmobile: Use SMP on Koelsch
ARM: shmobile: Remove KZM9D reference DTS
ARM: shmobile: Let KZM9D multiplatform boot with KZM9D DTB
ARM: shmobile: Remove non-multiplatform KZM9D reference support
ARM: shmobile: Use KZM9D without reference for multiplatform
ARM: shmobile: Sync KZM9D DTS with KZM9D reference DTS
...
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSgBrRAAoJEIwa5zzehBx3v+QP/1Z4DOzOckU7sb/IZZMXxVcS
C9G68x1n2lwqQwmMrjDAnFm+qKGDlb2SzHnUNiVy4niaGXdGSDtVzSEzK01LhUuz
BchWRy5Vb+pq0/bVLxtkqUPf0LEH/1as0uQVJNxwmV+SS9OvH+NpJHo2X6motYtX
W0l/NHwD/NYxwkjZTHUgZW9si1a8ZaG41i/h05IOpkww7RNcmtubWmQQIbKwmadc
z2QO3NsrcUvMgnoF9fOEJU2aurIx1s+6jpG6/fD1WWejCMuf0JulyfV7egREFgty
yp8QhnSTDaOvV0Gjrpx+4ERkwpVjvESpZIJoYHXjbScZHTCzkVDBLwwpmgYB1Mrb
KOKTt6+p8RAMFm43Rkf42SW8RXMM8nifed/H5Lwimi8qQT4+PuWM4i524P0Bb0Bj
tANHU2twUbY1VFRycGwWbTwPWtwxD4B0c6xflon84IGsZC31mvcfRcGaqaMtwTH4
J6CN0Bk3Tp0BUOveo0pdTPtrgOWm85MxWrzbjppKY7Lgl4A19iXqvSQjIt1sjJGz
5d8hH7KX26jKT24FiFp0fttOCRVVmg5Ks6sn2BTjX83w9S1pUg4yjZTU9cdbFbyN
zvi0d7YQYWOJTlSQlY5m5xqvRzeByAae4EDA6LKdh6JQsPyQEhHdxvMj7/ZURf8W
4jPMsgi+GxP8AGhpb20/
=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
The GPIO API defines 0 as being a valid GPIO number, so this field needs
to be initialized explicitly.
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Thierry Reding <treding@nvidia.com>
* Constify platform data and resources in lager board code
* Clean up registration of VIN and sh_eth in r8a7778 SoC and
bockw board code
* Make r8a7778_register_hspi() static in r8a7778 SoC code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSU5WFAAoJENfPZGlqN0++v5UP/26wi2e77h/7UMTmMq9HO0R3
L1LAyITkzFxvm1yiReoVT9ovs9XdxWG0SLhE/H/e8iqnWtNvPfPCVETPeegkCayA
ELFX+zc+c/dnGXOazY4rK1K+kPeR4aTBPNpkGLcpcxGlnSeBG2s8mpOHLeAMDWcW
A7iN8S/irWj0dtQ4b9QtrYzkU5mIa7E6vvYmAVWfJiOC5MN1cjMLEgGXm4EgVuwg
MkG33H8CnytO+QhC4EhAYOjROQ+t4Q0j9fFdq9AAJ5sL9VKm/83PQx198ikQY0yQ
rNbyn6dIzOp5cSJ1x3DzNegVtp6pCbiBvBjJmhLMX6YITRFEzXolxTSU6jU1+wZg
6wZ9d62tX8pGBxq/OV6harggZnjJ4jVDiJ72BTQ1R9c1SWcnQDd1/lFC/Xpxu7ku
dzzFxZnoB3tltkYI+AiJPhow8XsGaQFv22o3DyliHeHw/jBYho3v5/Y5Pzms0bCm
RwftNJx1FPa6j8MM8PYLnmklogSFSMquMAj8dtLE5w7pKaA1/s9n5KWB3UYagok2
cLWu7XOo0itw6+E/FMzJY1owvvHPka2F1W+Qad5GOlu8Qcc+Ys79UXd6JELOV8eX
yXHMqioTY5GWS0tnLAYjocEctHEYAORI7daoAtdGAHEhG93jLC8+Y7+U2h0Fx412
TdbcRFkrAeKD8T0zLJoy
=ZNhN
-----END PGP SIGNATURE-----
Merge tag 'renesas-cleanup2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
Second round of Renesas ARM based SoC cleanups for v3.13
* Constify platform data and resources in lager board code
* Clean up registration of VIN and sh_eth in r8a7778 SoC and
bockw board code
* Make r8a7778_register_hspi() static in r8a7778 SoC code
* tag 'renesas-cleanup2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: Constify platform data and resources
ARM: shmobile: r8a7778: r8a7778_register_hspi() become static
ARM: shmobile: r8a7778: cleanup registration of sh_eth
ARM: shmobile: r8a7778: cleanup registration of vin
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Conflicts:
arch/arm/mach-shmobile/board-lager.c
* SMP support for r8a7791 SoC
* r8a7779_init_irq_extpin() for DT for r8a7779 and r8a7778 SoCs
* Add HPB-DMAC to r8a7779 and r8a7778 SoCs
* Add r7s72100 SoC
* Make use of ARCH timer workaround on r8a7791 SoC
* Add IRQC platform device support to r8a7791 SoC
* Add I2C clocks and aliases for the DT mode for r8a7790 SoC
* Add MAC platform device to r8a73a4 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=4wdR
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Second Round of Renesas ARM based SoC updates for v3.13
* SMP support for r8a7791 SoC
* r8a7779_init_irq_extpin() for DT for r8a7779 and r8a7778 SoCs
* Add HPB-DMAC to r8a7779 and r8a7778 SoCs
* Add r7s72100 SoC
* Make use of ARCH timer workaround on r8a7791 SoC
* Add IRQC platform device support to r8a7791 SoC
* Add I2C clocks and aliases for the DT mode for r8a7790 SoC
* Add MAC platform device to r8a73a4 SoC
* tag 'renesas-soc2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791 SMP support
ARM: shmobile: r8a7779: split r8a7779_init_irq_extpin() for DT
ARM: shmobile: r8a7778: split r8a7778_init_irq_extpin() for DT
ARM: shmobile: r7s72100 SCIF support
ARM: shmobile: Initial r7s72100 SoC support
ARM: shmobile: r8a7791 Arch timer workaround
ARM: shmobile: r8a7791 IRQC platform device support
ARM: shmobile: Introduce r8a7791_add_standard_devices()
ARM: shmobile: Break out R-Car Gen2 setup code
ARM: shmobile: r8a73a4: add a clock alias for the DMAC in DT mode
ARM: shmobile: r8a7790: add I2C clocks and aliases for the DT mode
ARM: shmobile: r8a7779: add HPB-DMAC support
ARM: shmobile: r8a7778: add HPB-DMAC support
ARM: shmobile: r8a73a4: add a DMAC platform device and clock for it
ARM: shmobile: Remove #gpio-ranges-cells DT property
gpio: rcar: Remove #gpio-range-cells DT property usage
ARM: shmobile: armadillo: fixup ether pinctrl naming
ARM: shmobile: Lager: add Micrel KSZ8041 PHY fixup
ARM: shmobile: update SDHI DT compatibility string to the <unit>-<soc> format
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This patch adds missing INTC IRQ settings
which is required from SMSC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable r8a7791 SMP support code on the Koelsch board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Let the multiplatform KZM9D support boot with the
legacy DTS for KZM9D as well as the KZM9D reference DTS.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when CCF is supported remove the legacy KZM9D reference
Kconfig bits CONFIG_MACH_KZM9D_REFERENCE for the non-multiplatform
case.
Starting from this commit KZM9D board support is always enabled
via CONFIG_MACH_KZM9D, and CONFIG_ARCH_MULTIPLATFORM is used
to select between board-kzm9d.c and board-kzm9d-reference.c
The file board-kzm9d-reference.c can no longer be used together
with the legacy sh-clk clock framework, instead CCF is used.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change the multiplatform kconfig bits for KZM9D from
CONFIG_MACH_KZM9D_REFERENCE into CONFIG_MACH_KZM9D
to match the non-multiplatform case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make use of the R-Car Gen2 arch timer workaround on Koelsch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use r8a7791_add_standard_devices() on Koelsch to let
the C version of the board code add on-chip devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Genmai base board support making use of 128 MiB of memory,
the r7s7211 SoC with the SCIF2 serial port and CA9 core.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pass HPB-DMA slave IDs in the SDHI0 platform data to enable DMA in the SDHI
driver.
Signed-off-by: Max Filippov <max.filippov@cogentembedded.com>
[Sergei: removed #include <mach/dma.h>]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pass HPB-DMA slave IDs in the SDHI0 platform data to enable DMA in the SDHI
driver.
Signed-off-by: Max Filippov <max.filippov@cogentembedded.com>
[Sergei: removed #include <mach/dma.h>]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DMA support for MMCIF on APE6EVM, using the shdma dmaengine driver.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tie in the APMU SMP code on r8a7791. When used together
with the secondary CPU device node and smp_ops in the
board specific code then this will allow use of the
two Cortex-A15 cores in the r8a7791 SoC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7779 INTC needs IRL pin mode settings to determine
behavior of IRQ0 - IRQ3, and r8a7779_init_irq_extpin()
is controlling it via irlm parameter.
But this function registers renesas_intc_irqpin driver
if irlm was set, and this value depends on platform.
This is not good for DT.
This patch splits r8a7779_init_irq_extpin() function
into "mode settings" and "funtion register" parts
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7778 INTC needs IRL pin mode settings to determine
behavior of IRQ0 - IRQ3, and r8a7778_init_irq_extpin()
is controlling it via irlm parameter.
But this function registers renesas_intc_irqpin driver
if irlm was set, and this value depends on platform.
This is not good for DT.
This patch splits r8a7778_init_irq_extpin() function
into "mode settings" and "funtion register" parts.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SCIF serial port support to the r7s72100 SoC by
adding platform devices for SCIF0 -> SCIF7 together with
clock bindings. DT device description is excluded at
this point since such bindings are still under
development.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the r7272100 SoC including:
- Single Cortex-A9 CPU Core
- GIC
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make use of the R-Car Gen2 arch timer workaround on r8a7791.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a platform device for the r8a7791 IRQC hardware
driving IRQ pins IRQ0 to IRQ9. The Linux interrupt
number is statically assigned to allow board code
written in C to make use of static interrupt numbers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Introduce the function r8a7791_add_standard_devices() that
follows the same style as other mach-shmobile SoC code and
allows C version of board code to add on-chip devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move arch timer workaround code and boot mode pin
handling from setup-r8a7790.c to setup-rcar-gen2.c.
With this in place the same code can be used on
other R-Car Generation 2 devices such as r8a7791.
Signed-off-by: Magnus Damm <damm@opensource.se>
[horms+renesas@verge.net.au trivial rebase of board-lager.c
for introduction of lager_add_standard_devices()]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Devices, initialised from the Device Tree and from platform code usually
have different names. This patch adds a clock alias for DMAC on r8a73a4
in DT mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds clock definitions for the 4 I2C interfaces on r8a7790 and
clock aliases, suitable for the DT mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add HPB-DMAC platform device on R8A7779 SoC along with its slave and channel
configurations (only for SDHI0 so far).
Signed-off-by: Max Filippov <max.filippov@cogentembedded.com>
[Sergei: moved *enum* declaring HPB-DMAC slave IDs from now removed <mach/dma.h>
to <mach/r8a7779.h>, removed #include <mach/dma.h> from setup-r8a7779.c, removed
SSI-related *enum* values and SSI-related data from hpb_dmae_slaves[] and
hpb_dmae_channels[], added ASYNCMDR.ASBTMD{20|24|43} and ASYNCMDR.ASMD{20|24|43}
fields/values, fixed comments to ASYNCMDR.ASBTMD2[123] and ASYNCMDR.ASMD2[123]
fields/values, renamed all the bit/field/value #define's to include 'HBP_DMAE_'
prefix to match the driver, moved comments after the element initializers of
hpb_dmae_channels[].]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add HPB-DMAC platform device on R8A7778 SoC along with its slave and channel
configurations (only for SDHI0 so far).
Signed-off-by: Max Filippov <max.filippov@cogentembedded.com>
[Sergei: moved *enum* declaring HPB-DMAC slave IDs from now removed <mach/dma.h>
to <mach/r8a7778.h>, removed #include <mach/dma.h> from setup-r8a7778.c, removed
SSI-related *enum* values and SSI-related data from hpb_dmae_slaves[] and
hpb_dmae_channels[], moved the comments after the element initializers of
hpb_dmae_channels[].]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DMAC platform device and clock definitions for it on r8a73a4.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WVMt
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes4-for-v3.12' into soc2-base
Fourth Round of Renesas ARM based SoC fixes for v3.12
* Remove unused #gpio-ranges-cells DT property
* Remove usage of deprecated #gpio-range-cells DT property
from GPIO R-Car
Property was deprecated in v3.11-rc2
* Correct ether pinctl naming for armadillo800eva board
Regression introduced in v3.10-rc5
* Add Micrel KSZ8041 PHY fixup to lager board
This resolves a problem that has been present since 3.11-rc2
* Update SDHI DT compatibility string to the <unit>-<soc> format
This makes compatibility strings consistent across all renesas
hardware which currently supports DT.
The bindings which are being updated where intorodiced on
a per-SoC basis starting in v3.8-rc7. They may have
been internally consistent when originally added.
Tie in the APMU SMP code on r8a7791. When used together
with the secondary CPU device node and smp_ops in the
board specific code then this will allow use of the
two Cortex-A15 cores in the r8a7791 SoC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7779 INTC needs IRL pin mode settings to determine
behavior of IRQ0 - IRQ3, and r8a7779_init_irq_extpin()
is controlling it via irlm parameter.
But this function registers renesas_intc_irqpin driver
if irlm was set, and this value depends on platform.
This is not good for DT.
This patch splits r8a7779_init_irq_extpin() function
into "mode settings" and "funtion register" parts
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7778 INTC needs IRL pin mode settings to determine
behavior of IRQ0 - IRQ3, and r8a7778_init_irq_extpin()
is controlling it via irlm parameter.
But this function registers renesas_intc_irqpin driver
if irlm was set, and this value depends on platform.
This is not good for DT.
This patch splits r8a7778_init_irq_extpin() function
into "mode settings" and "funtion register" parts.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add SCIF serial port support to the r7s72100 SoC by
adding platform devices for SCIF0 -> SCIF7 together with
clock bindings. DT device description is excluded at
this point since such bindings are still under
development.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial support for the r7272100 SoC including:
- Single Cortex-A9 CPU Core
- GIC
No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Make use of the R-Car Gen2 arch timer workaround on r8a7791.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a platform device for the r8a7791 IRQC hardware
driving IRQ pins IRQ0 to IRQ9. The Linux interrupt
number is statically assigned to allow board code
written in C to make use of static interrupt numbers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Introduce the function r8a7791_add_standard_devices() that
follows the same style as other mach-shmobile SoC code and
allows C version of board code to add on-chip devices.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move arch timer workaround code and boot mode pin
handling from setup-r8a7790.c to setup-rcar-gen2.c.
With this in place the same code can be used on
other R-Car Generation 2 devices such as r8a7791.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Devices, initialised from the Device Tree and from platform code usually
have different names. This patch adds a clock alias for DMAC on r8a73a4
in DT mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds clock definitions for the 4 I2C interfaces on r8a7790 and
clock aliases, suitable for the DT mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add HPB-DMAC platform device on R8A7779 SoC along with its slave and channel
configurations (only for SDHI0 so far).
Signed-off-by: Max Filippov <max.filippov@cogentembedded.com>
[Sergei: moved *enum* declaring HPB-DMAC slave IDs from now removed <mach/dma.h>
to <mach/r8a7779.h>, removed #include <mach/dma.h> from setup-r8a7779.c, removed
SSI-related *enum* values and SSI-related data from hpb_dmae_slaves[] and
hpb_dmae_channels[], added ASYNCMDR.ASBTMD{20|24|43} and ASYNCMDR.ASMD{20|24|43}
fields/values, fixed comments to ASYNCMDR.ASBTMD2[123] and ASYNCMDR.ASMD2[123]
fields/values, renamed all the bit/field/value #define's to include 'HBP_DMAE_'
prefix to match the driver, moved comments after the element initializers of
hpb_dmae_channels[].]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add HPB-DMAC platform device on R8A7778 SoC along with its slave and channel
configurations (only for SDHI0 so far).
Signed-off-by: Max Filippov <max.filippov@cogentembedded.com>
[Sergei: moved *enum* declaring HPB-DMAC slave IDs from now removed <mach/dma.h>
to <mach/r8a7778.h>, removed #include <mach/dma.h> from setup-r8a7778.c, removed
SSI-related *enum* values and SSI-related data from hpb_dmae_slaves[] and
hpb_dmae_channels[], moved the comments after the element initializers of
hpb_dmae_channels[].]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DMAC platform device and clock definitions for it on r8a73a4.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
* Add CPU notifier based SCU boot vector code
- Use on emev2, r8a7779 and sh73a0 SoCs
- Remove now unused shmobile_smp_scu_boot_secondary()
* Add shared APMU SMP support code
- Use to add SMP support for r8a7790 SoC
* Introduce shmobile_boot_size
* Expose shmobile_invalidate_start()
* Introduce shmobile_smp_cpu_disable()
- Use on sh73a0 SoC
- Remove now unused shmobile_smp_init_cpus()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=Tn0W
-----END PGP SIGNATURE-----
Merge tag 'renesas-smp-for-v3.13' into soc2-base
Renesas ARM based SoC SMP updates for v3.13
* Add CPU notifier based SCU boot vector code
- Use on emev2, r8a7779 and sh73a0 SoCs
- Remove now unused shmobile_smp_scu_boot_secondary()
* Add shared APMU SMP support code
- Use to add SMP support for r8a7790 SoC
* Introduce shmobile_boot_size
* Expose shmobile_invalidate_start()
* Introduce shmobile_smp_cpu_disable()
- Use on sh73a0 SoC
- Remove now unused shmobile_smp_init_cpus()
* Display Unit support for lager and marzen boards
* Update regulators for MMC0, SDHI0 and SDHI1 on ape6evm board
* Enable use of FPGA on bockw board
* Add sounds support to bockw board
* Add USB function support to bockw board
* Add Koelsch board
* Disable MMCIF command completion signal on ape6evm, armadillo800eva,
kzm9g and lager boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=KUsf
-----END PGP SIGNATURE-----
Merge tag 'renesas-boards-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/boards
From Simon Horman:
Renesas ARM based SoC board updates for v3.13
* Display Unit support for lager and marzen boards
* Update regulators for MMC0, SDHI0 and SDHI1 on ape6evm board
* Enable use of FPGA on bockw board
* Add sounds support to bockw board
* Add USB function support to bockw board
* Add Koelsch board
* Disable MMCIF command completion signal on ape6evm, armadillo800eva,
kzm9g and lager boards.
* tag 'renesas-boards-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: disable MMCIF Command Completion Signal, add CLK_CTRL2
ARM: shmobile: kzm9g: disable MMCIF Command Completion Signal
ARM: shmobile: armadillo800eva: disable MMCIF Command Completion Signal
ARM: shmobile: ape6evm: disable MMCIF Command Completion Signal
ARM: shmobile: bockw: add USB Function support
ARM: shmobile: Koelsch support
ARM: shmobile: bockw: add R-Car sound support (PIO)
ARM: shmobile: bockw: enable global use of FPGA
ARM: shmobile: lager: Fix Display Unit platform data
ARM: shmobile: ape6evm: update MMC0, SDHI0 and SDHI1 with correct regulators
ARM: shmobile: lager: Add Display Unit support
ARM: shmobile: marzen: Add Display Unit support
ARM: shmobile: r8a7778: add usb phy power control function
ARM: shmobile: r8a7778: add USBHS clock
ARM: shmobile: r8a7791 CMT support
ARM: shmobile: r8a7791 SCIF support
ARM: shmobile: Initial r8a7791 SoC support
ARM: shmobile: r8a7778: add SSI/SRU clock support
ARM: shmobile: r8a7790: Add DU and LVDS clocks
ARM: shmobile: r8a7779: Rename DU device in clock lookups list
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add CPU notifier based SCU boot vector code
- Use on emev2, r8a7779 and sh73a0 SoCs
- Remove now unused shmobile_smp_scu_boot_secondary()
* Add shared APMU SMP support code
- Use to add SMP support for r8a7790 SoC
* Introduce shmobile_boot_size
* Expose shmobile_invalidate_start()
* Introduce shmobile_smp_cpu_disable()
- Use on sh73a0 SoC
- Remove now unused shmobile_smp_init_cpus()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=Tn0W
-----END PGP SIGNATURE-----
Merge tag 'renesas-smp-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Renesas ARM based SoC SMP updates for v3.13
* Add CPU notifier based SCU boot vector code
- Use on emev2, r8a7779 and sh73a0 SoCs
- Remove now unused shmobile_smp_scu_boot_secondary()
* Add shared APMU SMP support code
- Use to add SMP support for r8a7790 SoC
* Introduce shmobile_boot_size
* Expose shmobile_invalidate_start()
* Introduce shmobile_smp_cpu_disable()
- Use on sh73a0 SoC
- Remove now unused shmobile_smp_init_cpus()
* tag 'renesas-smp-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Include CA7 cores in APMU table
ARM: shmobile: Extend APMU code to allow single cluster only
ARM: shmobile: Remove shmobile_smp_scu_boot_secondary()
ARM: shmobile: Let r8a7779 rely on SCU CPU notifier
ARM: shmobile: Let EMEV2 rely on SCU CPU notifier
ARM: shmobile: Let sh73a0 rely on SCU CPU notifier
ARM: shmobile: Add CPU notifier based SCU boot vector code
ARM: shmobile: Add r8a7790 SMP support using APMU code
ARM: shmobile: Shared APMU SMP support code without DT
ARM: shmobile: Introduce shmobile_boot_size
ARM: shmobile: Expose shmobile_invalidate_start()
ARM: shmobile: Remove unused shmobile_smp_init_cpus()
ARM: shmobile: Use shmobile_smp_cpu_disable() on sh73a0
ARM: shmobile: Introduce shmobile_smp_cpu_disable()
ARM: shmobile: r8a7790: Constify platform data and resources
ARM: shmobile: Rename to r8a7790_init_early()
ARM: shmobile: Rename to r8a73a4_init_early()
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add support for r8a7791 SoC
* Rename DU device in clock lookups list of r8a7779 SoC
* USB and SSI/SRU clock support for r8a7778 SoC
* USB phy power control function support for r8a7778 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=GB2b
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Renesas ARM based SoC updates for v3.13
* Add support for r8a7791 SoC
* Rename DU device in clock lookups list of r8a7779 SoC
* USB and SSI/SRU clock support for r8a7778 SoC
* USB phy power control function support for r8a7778 SoC
* tag 'renesas-soc-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7778: add usb phy power control function
ARM: shmobile: r8a7778: add USBHS clock
ARM: shmobile: r8a7791 CMT support
ARM: shmobile: r8a7791 SCIF support
ARM: shmobile: Initial r8a7791 SoC support
ARM: shmobile: r8a7778: add SSI/SRU clock support
ARM: shmobile: r8a7790: Add DU and LVDS clocks
ARM: shmobile: r8a7779: Rename DU device in clock lookups list
Signed-off-by: Olof Johansson <olof@lixom.net>
* Constify platform data and resources of r8a7790 SoC
* Rename to r8a7790_init_delay() as r8a7790_init_early()
- This is in preparation for doing more than just initialising the delay
* Rename r8a73a4_init_delay() as r8a73a4_init_early()
- This is in preparation for doing more than just initialising the delay
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSSRy5AAoJENfPZGlqN0++sdUP/3b6wColkyIX0lVbenSQxyeL
5seUv0QsZY2wswIRlphFU8eZ/Oi5GF/7oXCx2tgjfZh1HaFpjV/Ocn+8bDL+7mOz
KeLV/togLZwZTAYohuXIsZnLhR13x3y+adCyEtOn3VVNz/CbXTEAJuSG9iA+M+o2
9Btmsvff6i6GVbv1ksf0kIsFA5NZXoykE3qay7b/GnImCNpMj9SgmIZt7hXl35IS
QdiRnmMJY2dl9WcTTIK2zHw+wxO29hMdpSsrEUOfQOcj8bPL09H35e2t5t+mx/bd
Z7dowu82e0CzZhzir0NbFvWZWjSF0Q0cYHpWWL89tU4Y+2vbICM0okwEc7UiO1b/
KlcyrApnQvTMsazbR1kBrZ3cwHi+xRdDw27njtVkYIh1AGCkYplezlmUl+ALNOKn
bCDh6XJOEDDuw7cuoKKwtsGUcVR+QCRNVUtbuUXwG1naCL06BUUpSvCrmCzsoUSW
VPbMZWURaE4X7LNL2Q63Kl6JzFzC8iGfzH/tST7/Zvhw/7uN2Ppsuz7K6Crkhi8a
zyITxIyiy+OKURFEUt8Fhy5mdkw9UUnAVjmAM6HPFGaxAfmsCV2Wvoks3I7/EBJl
ks8Y5L8SSRQLLY6j3yGABavTvgj3k9TnUxxzUJMYnMX1/D++ohHxTwS3Dj0TpXtb
p1D+V3Pz5mcfThlGRFg8
=1rby
-----END PGP SIGNATURE-----
Merge tag 'renesas-cleanup-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
Renesas ARM based SoC cleanups for v3.13
* Constify platform data and resources of r8a7790 SoC
* Rename to r8a7790_init_delay() as r8a7790_init_early()
- This is in preparation for doing more than just initialising the delay
* Rename r8a73a4_init_delay() as r8a73a4_init_early()
- This is in preparation for doing more than just initialising the delay
* tag 'renesas-cleanup-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: Constify platform data and resources
ARM: shmobile: Rename to r8a7790_init_early()
ARM: shmobile: Rename to r8a73a4_init_early()
Signed-off-by: Olof Johansson <olof@lixom.net>
* Correct incorrect placement of __initdata tag in ape6evm board code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=nVyt
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes5-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
* Correct incorrect placement of __initdata tag in ape6evm board code
* tag 'renesas-fixes5-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: ape6evm: fix incorrect placement of __initdata tag
(+ other patches already present in v3.12-rc4)
Signed-off-by: Olof Johansson <olof@lixom.net>
__initdata tag should be placed between the variable name and equal
sign for the variable to be placed in the intended .init.data section.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add information to the shared APMU code regarding
the APMU instance used to control the CA7 cores.
This can be used on r8a7790 and r8a73a4, but should
most likely be converted to DT in the future.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Extend the APMU code with a check to only allow boot
of CPU cores that sit in the same cluster as CPU0.
This makes it possible for people to use the r8a790
CA7 boot mode with CA7-cores only. The default CA15
boot mode will enable CA15 cores only. This is an
intentional software limitation to cope with lacking
scheduler support.
By removing this patch it is possible to run all 8 cores
in parallel, but this is not recommended without out of tree
scheduler modfications or custom user space code to control
the CPU affinitiy.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove shmobile_smp_scu_boot_secondary() since
it is no longer used. CPU boot vector setup is
instead handled by CPU notifiers.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when CPU notifiers are used for SCU boot vector
setup shmobile_smp_scu_boot_secondary() is no longer
needed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when CPU notifiers are used for SCU boot vector
setup shmobile_smp_scu_boot_secondary() is no longer
needed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now when CPU notifiers are used for SCU boot vector
setup shmobile_smp_scu_boot_secondary() is no longer
needed.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add CPU notifiers for the shared mach-shmobile SCU code
to allow removal of the shared SCU boot_secondary code.
Regarding notifiers, at CPU_UP_PREPARE time the SMP boot
vector is initialized so secondary CPU cores can boot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add r8a7790 SMP support using the shared APMU code. To enable
SMP the r8a7790 specific DTS needs to be updated to include
CPU cores, and this is happening in a separate patch.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Introduce shared APMU SMP code for mach-shmobile. Both SMP boot up
and CPU Hotplug is supported. This version does not use DT but
if needed this will be added as an incremental feature patch.
The code is designed around CONFIG_NR_CPUS and should in theory support
any number of APMUs, however due to the current DT-less static design
only a single APMU is supported.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MMCIF on r8a7790 doesn't support Command Completion Signal, but it does
implement a CE_CLK_CTRL2 register. Platform parameters have to be added to
account for these features on lager.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MMCIF on sh73a0 doesn't support Command Completion Signal, a platform
parameter has to be added to disable it on kzm9g.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MMCIF on r8a7740 doesn't support Command Completion Signal, a platform
parameter has to be added to disable it on armadillo800eva.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MMCIF on r8a73a4 doesn't support Command Completion Signal, a platform
parameter has to be added to disable it on ape6evm.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Bock-W USB1 (CN29) can be USB Host/Func by SW98/SW99 settings.
USB Func will be enabled if CONFIG_USB_RENESAS_USBHS_UDC[_MODULE]
was selected on this patch
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Koelsch base board support making use of 2 GiB of memory,
the r8a7791 SoC with the SCIF0 serial port and CA15 with
CMT timer.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
[damm@opensource.se: Forward ported to upstream, dropped not-yet-ready SMP/PFC]
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables R-Car sound,
AK4643 (CN19) and AK4554 (CN20/CN21) codec chip
on Bock-W.
But, it supports PIO transfer only at this point.
User can check sound settings (Dip-switch/PFC etc)
via this patch, but will get under/over flow error
when playback/capture.
Because PIO transfer via SSI will be interrupted
"sampling rate" times per 1 second.
DMA transfer will be supported when HPB-DMAC was
enabled on r8a7778.
You will notice strange ALSA sound card HW
numbering on Bock-W board.
This came from AK4554 strange format on playback/capture.
The format on playback/capture is same on "normal" codec chip,
but AK4554 was different.
Because of that, AK4554 playback/capture are
registered as a different sound card.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[horms+renesas@verge.net.au: squashed cleanup of SND_SOC_xxx in
Kconfig by Kuninori Morimoto]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch enables global use of FPGA,
since it will be used from many devices.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DU device erroneously receives the DU resources array as platform
data instead of the DU platform data structure. Fix it.
This problem was introduced by f631fa0 ("ARM: shmobile: lager: Add Display
Unit support").
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently a dummy fixed always-on regulator is used for all 3 SD/MMC
interfaces on ape6evm. This patch updates the board to use correct supplies
for MMC0, SDHI0 and SDHI1 VDD. SDHI0 VccQ supply regulator should be
implemented in a separate patch.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Only the VGA output is currently supported.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Platform data and resources for Lager devices are kmemdup()ed when the
corresponding devices are registered and can thus be declared as const.
Do so.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Valentine Barshak
Shinya Kuribayashi
Laurent Pinchart
Simon Horman
Geert Uytterhoeven
Takashi Yoshii
Ulrich Hecht
Kuninori Morimoto
Sergei Shtylyov
Rob Herring
Linus Torvalds
Olof Johansson
Laurent Pinchart
Wolfram Sang
Kevin Hilman
Uwe Kleine-König
Wolfram Sang
Ben Dooks
Hiep Cao Minh
Paul Walmsley
Magnus Damm
Thierry Reding
Max Filippov
Guennadi Liakhovetski
Bartlomiej Zolnierkiewicz
Hisashi Nakamura