When the Address-Based Interrupt Trigger mode is activated, the PHB
maps the interrupt source number into the interrupt command address.
The PHB directly triggers the IC ESB page of the interrupt number and
not the notify page of the IC anymore.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The PQ_disable configuration bit disables the check done on the PQ
state bits when processing new MSI interrupts. When bit 9 is enabled,
the PHB forwards any MSI trigger to the XIVE interrupt controller
without checking the PQ state bits. The XIVE IC knows from the trigger
message that the PQ bits have not been checked and performs the check
locally.
This configuration bit only applies to MSIs and LSIs are still checked
on the PHB to handle the assertion level.
PQ_disable enablement is a requirement for StoreEOI.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
PHB5 will introduce its own root port model. Prepare ground for it.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220117122753.1655504-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
All the complexity that was scattered between PnvPhb4PecStack and
PnvPHB4 are now centered in the PnvPHB4 device. PnvPhb4PecStack does not
serve any purpose in the current code base.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220114180719.52117-8-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This patch changes the design of the PEC device to create and realize PHB4s
instead of PecStacks. After all the recent changes, PHB4s now contain all
the information needed for their proper functioning, not relying on PecStack
in any capacity.
All changes are being made in a single patch to avoid renaming parts of
the PecState and leaving the code in a strange way. E.g. rename
PecClass->num_stacks to num_phbs, which would then read a
pnv_pec_num_stacks[] array. To avoid mixing the old and new design more
than necessary it's clearer to do these changes in a single step.
The name changes made are:
- in PnvPhb4PecState:
* rename 'num_stacks' to 'num_phbs'
* remove the pec->stacks[] array. Current code relies on the
pec->stacks[] obj acting as a simple container, without ever accessing
pec->stacks[] for any other purpose. Instead of converting this into a
pec->phbs[] array, remove it
- in PnvPhb4PecClass, rename *num_stacks to *num_phbs;
- pnv_pec_num_stacks[] is renamed to pnv_pec_num_phbs[].
The logical changes:
- pnv_pec_default_phb_realize():
* init and set the properties of the PnvPHB4 qdev
* do not use stack->phb anymore;
- pnv_pec_realize():
* use the new default_phb_realize() to init/realize each PHB if
running with defaults;
- pnv_pec_instance_init(): removed since we're creating the PHBs during
pec_realize();
- pnv_phb4_get_stack():
* renamed to pnv_phb4_get_pec() and returns a PnvPhb4PecState*;
- pnv_phb4_realize(): use 'phb->pec' instead of 'stack'.
This design change shouldn't caused any behavioral change in the runtime
of the machine.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220114180719.52117-7-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
pnv_pec_default_phb_realize() stopped using it after the previous patch and
no one else is using it.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220114180719.52117-6-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This pointer was being used for two reasons: pnv_phb4_update_regions()
was using it to access the PHB and phb4_realize() was using it as a way
to determine if the PHB was user created.
We can determine if the PHB is user created via phb->pec, introduced in
the previous patch, and pnv_phb4_update_regions() is no longer using
stack->phb.
Remove the pointer from the PnvPHB4 device.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220114180719.52117-4-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This property will track the owner PEC of this PHB. For now it's
redundant since we can retrieve the PEC via phb->stack->pec but it
will not be redundant when we get rid of the stack device.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220114180719.52117-2-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
After recent changes, this MemoryRegion can be migrated to PnvPHB4
without too much trouble.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220113192952.911188-11-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
We're now able to cleanly move nest_regs_mr to the PnvPHB4 device.
One thing of notice here is the need to use a phb->stack->pec pointer
because pnv_pec_stk_nest_xscom_write requires a PEC object. Another
thing that can be noticed in the use of 'stack->stack_no' that still
remains throughout the XSCOM code.
After moving all MemoryRegions to the PnvPHB4 object, this illustrates
what is the remaining role of the stack: provide a PEC pointer and the
'stack_no' information. If we can provide these in the PnvPHB4 object
instead (spoiler: we can, and we will), the PnvPhb4PecStack device will
be deprecated and can be removed.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220113192952.911188-10-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
stack->nest_regs[] is used in several XSCOM functions and it's one of
the main culprits of having to deal with stack->phb pointers around the
code.
Sure, we're having to add 2 extra stack->phb pointers to ease
nest_regs[] migration to PnvPHB4. They'll be dealt with shortly.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220113192952.911188-8-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
These 2 MemoryRegions, together with mmio(0|1)_base and mmio(0|1)_size
variables, are used together in the same functions. We're better of
moving them all in a single step.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220113192952.911188-7-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This MemoryRegion can also be moved in a single step.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220113192952.911188-5-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This MemoryRegion is simple enough to be moved in a single step.
A 'stack->phb' pointer had to be introduced in pnv_pec_stk_update_map()
because this function isn't ready to be fully converted to use a PnvPHB4
pointer instead. This will be dealt with in the following patches.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220113192952.911188-4-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Previous patch changed pnv_pec_stk_pci_xscom_read() and
pnv_pec_stk_pci_xscom_write() to use a PnvPHB4 opaque, making it easier
to move both pci_regs[] and the pci_regs_mr MemoryRegion to the PnvHB4
object.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220113192952.911188-3-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Its only callers are inside pnv_phb4.c.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220111131027.599784-6-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
At this moment, stack->phb is the plain PnvPHB4 device itself instead of
a pointer to the device. This will present a problem when adding user
creatable devices because we can't deal with this struct and the
realize() callback from the user creatable device.
We can't get rid of this attribute, similar to what we did when enabling
pnv-phb3 user creatable devices, because pnv_phb4_update_regions() needs
to access stack->phb to do its job. This function is called twice in
pnv_pec_stk_update_map(), which is one of the nested xscom write
callbacks (via pnv_pec_stk_nest_xscom_write()). In fact,
pnv_pec_stk_update_map() code comment is explicit about how the order of
the unmap/map operations relates with the PHB subregions.
All of this indicates that this code is tied together in a way that we
either go on a crusade, featuring lots of refactories and redesign and
considerable pain, to decouple stack and phb mapping, or we allow stack
update_map operations to access the associated PHB as it is today even
after introducing pnv-phb4 user devices.
This patch chooses the latter. Instead of getting rid of stack->phb,
turn it into a PHB pointer. This will allow us to assign an user created
PHB to an existing stack later. In this process,
pnv_pec_stk_instance_init() is removed because stack->phb is being
initialized in stk_realize() instead.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220111131027.599784-4-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The logic inside pnv_pec_phb_offset() will be useful in the next patch
to determine the stack that should contain a PHB4 device.
Move the function to pnv_phb4.c and make it public since there's no
pnv_phb4_pec.h header. While we're at it, add 'stack_index' as a
parameter and make the function return 'phb-id' directly. And rename it
to pnv_phb4_pec_get_phb_id() to be even clearer about the function
intent.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220110143346.455901-3-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Similar to what was happening with pnv-phb3 buses,
TYPE_PNV_PHB4_ROOT_BUS set to "pnv-phb4-root-bus" is a bit too long for
a default root bus name. The usual default name for theses buses in QEMU
are 'pcie', but we want to make a distinction between pnv-phb4 buses and
other PCIE buses, at least as far as default name goes, because not all
PCIE devices are attachable to a pnv-phb4 root-bus type.
Changing the default to 'pnv-phb4-root' allow us to have a shorter name
while making this bus distinct, and the user can always set its own bus
naming via the "id" attribute anyway.
This is the 'info qtree' output after this change, using a powernv9
domain with 2 sockets and default settings enabled:
qemu-system-ppc64 -m 4G -machine powernv9,accel=tcg \
-smp 2,sockets=2,cores=1,threads=1
dev: pnv-phb4, id ""
index = 5 (0x5)
chip-id = 1 (0x1)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb4-root.11
type pnv-phb4-root
dev: pnv-phb4-root-port, id ""
(...)
dev: pnv-phb4, id ""
index = 0 (0x0)
chip-id = 1 (0x1)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb4-root.6
type pnv-phb4-root
dev: pnv-phb4-root-port, id ""
(..)
dev: pnv-phb4, id ""
index = 5 (0x5)
chip-id = 0 (0x0)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb4-root.5
type pnv-phb4-root
dev: pnv-phb4-root-port, id ""
(...)
dev: pnv-phb4, id ""
index = 0 (0x0)
chip-id = 0 (0x0)
version = 704374636546 (0xa400000002)
device-id = 1217 (0x4c1)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb4-root.0
type pnv-phb4-root
dev: pnv-phb4-root-port, id ""
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220110143346.455901-11-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The TYPE_PNV_PHB3_ROOT_BUS name is used as the default bus name when
the dev has no 'id'. However, pnv-phb3-root-bus is a bit too long to be
used as a bus name.
Most common QEMU buses and PCI controllers are named based on their bus
type (e.g. pSeries spapr-pci-host-bridge is called 'pci'). The most
common name for a PCIE bus controller in QEMU is 'pcie'. Naming it
'pcie' would break the documented use of the pnv-phb3 device, since
'pcie.0' would now refer to the root bus instead of the first root port.
There's nothing particularly wrong with the 'root-bus' name used before,
aside from the fact that 'root-bus' is being used for pnv-phb3 and
pnv-phb4 created buses, which is not quite correct since these buses
aren't implemented the same way in QEMU - you can't plug a
pnv-phb4-root-port into a pnv-phb3 root bus, for example.
This patch renames it as 'pnv-phb3-root', which is a compromise between
the existing and the previously used name. Creating 3 phbs without ID
will result in an "info qtree" output similar to this:
bus: main-system-bus
type System
dev: pnv-phb3, id ""
index = 2 (0x2)
chip-id = 0 (0x0)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb3-root.2
type pnv-phb3-root
(...)
dev: pnv-phb3, id ""
index = 1 (0x1)
chip-id = 0 (0x0)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb3-root.1
type pnv-phb3-root
(...)
dev: pnv-phb3, id ""
index = 0 (0x0)
chip-id = 0 (0x0)
x-config-reg-migration-enabled = true
bypass-iommu = false
bus: pnv-phb3-root.0
type pnv-phb3-root
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220105212338.49899-11-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
We want to create only the absolutely minimal amount of devices when
running with -nodefaults. The root port is something that the machine
can boot up without. But, to do that, we need to provide a way for the
user to add them by hand.
This patch makes pnv-phb4-root-port user creatable and then uses the
pnv_phb_attach_root_port() helper to add a pnv_phb4_root_port only when
running with default settings.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220105212338.49899-5-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This cleanups the PHB3 model a bit more since the root port is an
independent device and it will ease our task when adding user created
PHB3s.
pnv_phb_attach_root_port() is made public in pnv.c so it can be reused
with the pnv_phb4 root port later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20220105212338.49899-4-danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Each PEC device of the POWER9 chip has a predefined number of stacks,
equivalent of a root port complex:
PEC0 -> 1 stack
PEC1 -> 2 stacks
PEC2 -> 3 stacks
Introduce a class attribute to hold these values and remove the
"num-stacks" property.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-11-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
And check the PEC index using the chip class.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-10-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It prepares ground for PHB5 which has different values.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-9-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This change will help us move the mapping of XSCOM regions under the
PHB3 realize routine, which will be necessary for user created PHB3
devices.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20211213132830.108372-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
commit c0e427d6eb ("hw/acpi/ich9: Enable ACPI PCI hot-plug") removed all
uses of find_i440fx() function. This has been replaced by the more generic call
acpi_get_i386_pci_host() which maybe able to find the root bus both for i440fx
machine type as well as for the q35 machine type. There seems to be no more any
need to maintain a i440fx specific version of the api call. Remove it.
Tested by building from a clean tree successfully.
Signed-off-by: Ani Sinha <ani@anisinha.ca>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210825031949.919376-2-ani@anisinha.ca>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Here's the first ppc pull request for qemu-6.1. It has a wide variety
of stuff accumulated during the 6.0 freeze. Highlights are:
* Multi-phase reset cleanups for PAPR
* Preliminary cleanups towards allowing !CONFIG_TCG for the ppc target
* Cleanup of AIL logic and extension to POWER10
* Further improvements to handling of hot unplug failures on PAPR
* Allow much larger numbers of CPU on pseries
* Support for the H_SCM_HEALTH hypercall
* Add support for the Pegasos II board
* Substantial cleanup to hflag handling
* Assorted minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=N0qr
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.1-20210504' into staging
ppc patch queue 2021-05-04
Here's the first ppc pull request for qemu-6.1. It has a wide variety
of stuff accumulated during the 6.0 freeze. Highlights are:
* Multi-phase reset cleanups for PAPR
* Preliminary cleanups towards allowing !CONFIG_TCG for the ppc target
* Cleanup of AIL logic and extension to POWER10
* Further improvements to handling of hot unplug failures on PAPR
* Allow much larger numbers of CPU on pseries
* Support for the H_SCM_HEALTH hypercall
* Add support for the Pegasos II board
* Substantial cleanup to hflag handling
* Assorted minor fixes and cleanups
# gpg: Signature made Tue 04 May 2021 06:52:39 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.1-20210504: (46 commits)
hw/ppc/pnv_psi: Use device_cold_reset() instead of device_legacy_reset()
hw/ppc/spapr_vio: Reset TCE table object with device_cold_reset()
hw/intc/spapr_xive: Use device_cold_reset() instead of device_legacy_reset()
target/ppc: removed VSCR from SPR registration
target/ppc: Reduce the size of ppc_spr_t
target/ppc: Clean up _spr_register et al
target/ppc: Add POWER10 exception model
target/ppc: rework AIL logic in interrupt delivery
target/ppc: move opcode table logic to translate.c
target/ppc: code motion from translate_init.c.inc to gdbstub.c
spapr_drc.c: handle hotunplug errors in drc_unisolate_logical()
spapr.h: increase FDT_MAX_SIZE
spapr.c: do not use MachineClass::max_cpus to limit CPUs
ppc: Rename current DAWR macros and variables
target/ppc: POWER10 supports scv
target/ppc: Fix POWER9 radix guest HV interrupt AIL behaviour
docs/system: ppc: Add documentation for ppce500 machine
roms/u-boot: Bump ppce500 u-boot to v2021.04 to fix broken pci support
roms/Makefile: Update ppce500 u-boot build directory name
ppc/spapr: Add support for implement support for H_SCM_HEALTH
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Marvell Discovery II aka. MV64361 is a PowerPC system controller
chip that is used on the pegasos2 PPC board. This adds emulation of it
that models the device enough to boot guests on this board. The
mv643xx.h header with register definitions is taken from Linux 4.15.10
only fixing white space errors, removing not needed parts and changing
formatting for QEMU coding style.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <79545ebd03bfe0665b73d2d7cbc74fdf3d62629e.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The include/hw/hw.h header only has a prototype for hw_error(),
so it does not make sense to include this in files that do not
use this function.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210326151848.2217216-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Currently the gpex PCI controller implements no special behaviour for
guest accesses to areas of the PIO and MMIO where it has not mapped
any PCI devices, which means that for Arm you end up with a CPU
exception due to a data abort.
Most host OSes expect "like an x86 PC" behaviour, where bad accesses
like this return -1 for reads and ignore writes. In the interests of
not being surprising, make host CPU accesses to these windows behave
as -1/discard where there's no mapped PCI device.
The old behaviour generally didn't cause any problems, because
almost always the guest OS will map the PCI devices and then only
access where it has mapped them. One corner case where you will see
this kind of access is if Linux attempts to probe legacy ISA
devices via a PIO window access. So far the only case where we've
seen this has been via the syzkaller fuzzer.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210325163315.27724-1-peter.maydell@linaro.org
Fixes: https://bugs.launchpad.net/qemu/+bug/1918917
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
x-remote-machine object sets up various subsystems of the remote
device process. Instantiate PCI host bridge object and initialize RAM, IO &
PCI memory regions.
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: c537f38d17f90453ca610c6b70cf3480274e0ba1.1611938319.git.jag.raman@oracle.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
PCI host bridge is setup for the remote device process. It is
implemented using remote-pcihost object. It is an extension of the PCI
host bridge setup by QEMU.
Remote-pcihost configures a PCI bus which could be used by the remote
PCI device to latch on to.
Signed-off-by: Jagannathan Raman <jag.raman@oracle.com>
Signed-off-by: John G Johnson <john.g.johnson@oracle.com>
Signed-off-by: Elena Ufimtseva <elena.ufimtseva@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 0871ba857abb2eafacde07e7fe66a3f12415bfb2.1611938319.git.jag.raman@oracle.com
[Added PCI_EXPRESS condition in hw/remote/Kconfig since remote-pcihost
needs PCIe. This solves "make check" failure on s390x. Fix suggested by
Philippe Mathieu-Daudé <philmd@redhat.com> and Thomas Huth
<thuth@redhat.com>.
--Stefan]
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
It is currently not possible to perform a strict boot from USB storage:
$ qemu-system-ppc64 -accel kvm -nodefaults -nographic -serial stdio \
-boot strict=on \
-device qemu-xhci \
-device usb-storage,drive=disk,bootindex=0 \
-blockdev driver=file,node-name=disk,filename=fedora-ppc64le.qcow2
SLOF **********************************************************************
QEMU Starting
Build Date = Jul 17 2020 11:15:24
FW Version = git-e18ddad8516ff2cf
Press "s" to enter Open Firmware.
Populating /vdevice methods
Populating /vdevice/vty@71000000
Populating /vdevice/nvram@71000001
Populating /pci@800000020000000
00 0000 (D) : 1b36 000d serial bus [ usb-xhci ]
No NVRAM common partition, re-initializing...
Scanning USB
XHCI: Initializing
USB Storage
SCSI: Looking for devices
101000000000000 DISK : "QEMU QEMU HARDDISK 2.5+"
Using default console: /vdevice/vty@71000000
Welcome to Open Firmware
Copyright (c) 2004, 2017 IBM Corporation All rights reserved.
This program and the accompanying materials are made available
under the terms of the BSD License available at
http://www.opensource.org/licenses/bsd-license.php
Trying to load: from: /pci@800000020000000/usb@0/storage@1/disk@101000000000000 ...
E3405: No such device
E3407: Load failed
Type 'boot' and press return to continue booting the system.
Type 'reset-all' and press return to reboot the system.
Ready!
0 >
The device tree handed over by QEMU to SLOF indeed contains:
qemu,boot-list =
"/pci@800000020000000/usb@0/storage@1/disk@101000000000000 HALT";
but the device node is named usb-xhci@0, not usb@0.
This happens because the firmware names of PCI devices returned
by get_boot_devices_list() come from pcibus_get_fw_dev_path(),
while the sPAPR PHB code uses a different naming scheme for
device nodes. This inconsistency has always been there but it was
hidden for a long time because SLOF used to rename USB device
nodes, until this commit, merged in QEMU 4.2.0 :
commit 85164ad4ed
Author: Alexey Kardashevskiy <aik@ozlabs.ru>
Date: Wed Sep 11 16:24:32 2019 +1000
pseries: Update SLOF firmware image
This fixes USB host bus adapter name in the device tree to match QEMU's
one.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Fortunately, sPAPR implements the firmware path provider interface.
This provides a way to override the default firmware paths.
Just factor out the sPAPR PHB naming logic from spapr_dt_pci_device()
to a helper, and use it in the sPAPR firmware path provider hook.
Fixes: 85164ad4ed ("pseries: Update SLOF firmware image")
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20210122170157.246374-1-groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Running a guest with 128 NUMA nodes crashes QEMU:
../../util/error.c:59: error_setv: Assertion `*errp == NULL' failed.
The crash happens when setting the FWNMI migration blocker:
2861 if (spapr_get_cap(spapr, SPAPR_CAP_FWNMI) == SPAPR_CAP_ON) {
2862 /* Create the error string for live migration blocker */
2863 error_setg(&spapr->fwnmi_migration_blocker,
2864 "A machine check is being handled during migration. The handler"
2865 "may run and log hardware error on the destination");
2866 }
Inspection reveals that papr->fwnmi_migration_blocker isn't NULL:
(gdb) p spapr->fwnmi_migration_blocker
$1 = (Error *) 0x8000000004000000
Since this is the only place where papr->fwnmi_migration_blocker is
set, this means someone wrote there in our back. Further analysis
points to spapr_numa_associativity_init(), especially the part
that initializes the associative arrays for NVLink GPUs:
max_nodes_with_gpus = nb_numa_nodes + NVGPU_MAX_NUM;
ie. max_nodes_with_gpus = 128 + 6, but the array isn't sized to
accommodate the 6 extra nodes:
struct SpaprMachineState {
.
.
.
uint32_t numa_assoc_array[MAX_NODES][NUMA_ASSOC_SIZE];
Error *fwnmi_migration_blocker;
};
and the following loops happily overwrite spapr->fwnmi_migration_blocker,
and probably more:
for (i = nb_numa_nodes; i < max_nodes_with_gpus; i++) {
spapr->numa_assoc_array[i][0] = cpu_to_be32(MAX_DISTANCE_REF_POINTS);
for (j = 1; j < MAX_DISTANCE_REF_POINTS; j++) {
uint32_t gpu_assoc = smc->pre_5_1_assoc_refpoints ?
SPAPR_GPU_NUMA_ID : cpu_to_be32(i);
spapr->numa_assoc_array[i][j] = gpu_assoc;
}
spapr->numa_assoc_array[i][MAX_DISTANCE_REF_POINTS] = cpu_to_be32(i);
}
Fix the size of the array. This requires "hw/ppc/spapr.h" to see
NVGPU_MAX_NUM. Including "hw/pci-host/spapr.h" introduces a
circular dependency that breaks the build, so this moves the
definition of NVGPU_MAX_NUM to "hw/ppc/spapr.h" instead.
Reported-by: Min Deng <mdeng@redhat.com>
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1908693
Fixes: dd7e1d7ae4 ("spapr_numa: move NVLink2 associativity handling to spapr_numa.c")
Cc: danielhb413@gmail.com
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160829960428.734871.12634150161215429514.stgit@bahia.lan>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
While this change helps triskaidekaphobic developers, it
is a good practice to avoid magic values and using constant
definitions instead.
Introduce the PAM_REGIONS_COUNT and use it. No logical change.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Julia Suvorova <jusual@redhat.com>
Message-Id: <20201202132038.1276404-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The resources of pxbs are obtained by crs_build and the resources
used by pxbs would be moved from the resources defined for host-bridge.
The resources for pxb are composed of following two parts:
1. The bar space of the pci-bridge/pcie-root-port behined it
2. The config space of devices behind it.
Signed-off-by: Yubo Miao <miaoyubo@huawei.com>
Signed-off-by: Jiahui Cen <cenjiahui@huawei.com>
Message-Id: <20201119014841.7298-6-cenjiahui@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
This patch contains all the files, whose maintainer I could not get
from ‘get_maintainer.pl’ script.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023124424.20177-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Adapted exec.c and qdev-monitor.c to new location]
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20201023122633.19466-1-chetan4windows@gmail.com>
[PMD: Added hw/mips/ prefix in subject]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Currently an object link property is used to pass a reference to the OpenPIC
into the PCI host bridge so that pci_unin_init_irqs() can connect the PCI
IRQs to the PIC itself.
This can be simplified by defining the PCI IRQs as qdev gpios and then wiring
up the PCI IRQs to the PIC in the New World machine init function.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201013114922.2946-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Add helper function to generate dsdt aml code for the gpex pci host.
Largely copied from arm/virt. Configuration is handled by passing
a config struct instead of looked up from memory map.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20200928104256.9241-3-kraxel@redhat.com
Make the type checking macro name consistent with the TYPE_*
constant.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200902224311.1321159-49-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This looks like a copy/paste mistake: the instance type checking
macro for TYPE_GPEX_ROOT_DEVICE was named MCH_PCI_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200902224311.1321159-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
