This patch adds fan_splitters (split IRQs) in NPCM7XX boards. Each fan
splitter corresponds to 1 PWM output and can connect to multiple fan
inputs (MFT devices).
In NPCM7XX boards(NPCM750 EVB and Quanta GSJ boards), we initializes
these splitters and connect them to their corresponding modules
according their specific device trees.
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210311180855.149764-5-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The virt machine already checks KVM_CAP_ARM_VM_IPA_SIZE to get the
upper bound of the IPA size. If that bound is lower than the highest
possible GPA for the machine, then QEMU will error out. However, the
IPA is set to 40 when the highest GPA is less than or equal to 40,
even when KVM may support an IPA limit as low as 32. This means KVM
may fail the VM creation unnecessarily. Additionally, 40 is selected
with the value 0, which means use the default, and that gets around
a check in some versions of KVM, causing a difficult to debug fail.
Always use the IPA size that corresponds to the highest possible GPA,
unless it's lower than 32, in which case use 32. Also, we must still
use 0 when KVM only supports the legacy fixed 40 bit IPA.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Message-id: 20210310135218.255205-3-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Convert all sid printouts to sid=0x%x.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20210309102742.30442-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the whole SID range (32b) is invalidated (SMMU_CMD_CFGI_ALL),
@end overflows and we fail to handle the command properly.
Once this gets fixed, the current code really is awkward in the
sense it loops over the whole range instead of removing the
currently cached configs through a hash table lookup.
Fix both the overflow and the lookup.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210309102742.30442-7-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of today, the driver can invalidate a number of pages that is
not a power of 2. However IOTLB unmap notifications and internal
IOTLB invalidations work with masks leading to erroneous
invalidations.
In case the range is not a power of 2, split invalidations into
power of 2 invalidations.
When looking for a single page entry in the vSMMU internal IOTLB,
let's make sure that if the entry is not found using a
g_hash_table_remove() we iterate over all the entries to find a
potential range that overlaps it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210309102742.30442-6-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If the asid is not set, do not attempt to locate the key directly
as all inserted keys have a valid asid.
Use g_hash_table_foreach_remove instead.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210309102742.30442-5-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for the Versal Accelerator RAMs (XRAMs).
Reviewed-by: Luc Michel <luc@lmichel.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210308224637.2949533-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmBI50MACgkQ+9DbCVqe
KkSyKggAhPZW+7sReVEsFdnVfwuo3evW7auoW44mghNbikTnm3RfoahYTrek8lGZ
AEo2gFMbzENW0j88e0OvSYYtwkVz3sD68bygfXerti6sQwWlwkf42I/suWjJNLph
oVKGEEdJess9+zR13Cu6RAq5RaTwzDPGPjUwTbeJPpAps4+UZV3hsxhaxs8keII6
GBa/idnh0qEApP2NDLKiSASrYZM7xGvljE7zO4qhchd6iSH/o5rCtkoB2tRCcXGo
+KF8LyBsUNf7GiWp0yYZMZUQ3Pqskqma8N3d2A4UlS1kXvxeX/FiORkG/Ne8bH1Z
VZ1Z/xbyXGlVkiP1bcoYSc6XWHNDTw==
=R9zQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2' into staging
Testing, guest-loader and other misc tweaks
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
# gpg: Signature made Wed 10 Mar 2021 15:35:31 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2:
semihosting: Move hw/semihosting/ -> semihosting/
semihosting: Move include/hw/semihosting/ -> include/semihosting/
tests/avocado: add boot_xen tests
docs: add some documentation for the guest-loader
docs: move generic-loader documentation into the main manual
hw/core: implement a guest-loader to support static hypervisor guests
device_tree: add qemu_fdt_setprop_string_array helper
hw/riscv: migrate fdt field to generic MachineState
hw/board: promote fdt from ARM VirtMachineState to MachineState
.editorconfig: update the automatic mode setting for Emacs
tests/docker: Use --arch-only when building Debian cross image
gitlab-ci.yml: Add jobs to test CFI flags
gitlab-ci.yml: Allow custom # of parallel linkers
tests/docker: add a test-tcg for building then running check-tcg
docs/system: add a gentle prompt for the complexity to come
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* New model for the Aspeed LPC controller
* Misc cleanups
-----BEGIN PGP SIGNATURE-----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=SWwQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20210309' into staging
Aspeed patches :
* New model for the Aspeed LPC controller
* Misc cleanups
# gpg: Signature made Tue 09 Mar 2021 11:54:25 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20210309:
hw/misc: Model KCS devices in the Aspeed LPC controller
hw/misc: Add a basic Aspeed LPC controller model
hw/arm: ast2600: Correct the iBT interrupt ID
hw/arm: ast2600: Set AST2600_MAX_IRQ to value from datasheet
hw/arm: ast2600: Force a multiple of 32 of IRQs for the GIC
hw/arm/aspeed: Fix location of firmware images in documentation
arm/ast2600: Fix SMP booting with -kernel
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The use of FDT's is quite common across our various platforms. To
allow the guest loader to tweak it we need to make it available in
the generic state. This creates the field and migrates the initial
user to use the generic field. Other boards will be updated in later
patches.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-2-alex.bennee@linaro.org>
Add a Xilinx CSU DMA module to ZynqMP SoC, and connent the stream
link of GQSPI to CSU DMA.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are some coding convention warnings in xlnx-zynqmp.c and
xlnx-zynqmp.h, as reported by:
$ ./scripts/checkpatch.pl include/hw/arm/xlnx-zynqmp.h
$ ./scripts/checkpatch.pl hw/arm/xlnx-zynqmp.c
Let's clean them up.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Keyboard-Controller-Style devices for IPMI purposes are exposed via LPC
IO cycles from the BMC to the host.
Expose support on the BMC side by implementing the usual MMIO
behaviours, and expose the ability to inspect the KCS registers in
"host" style by accessing QOM properties associated with each register.
The model caters to the IRQ style of both the AST2600 and the earlier
SoCs (AST2400 and AST2500). The AST2600 allocates an IRQ for each LPC
sub-device, while there is a single IRQ shared across all subdevices on
the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-6-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a very minimal framework to access registers which are used to
configure the AHB memory mapping of the flash chips on the LPC HC
Firmware address space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-Id: <20210302014317.915120-5-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The AST2600 allocates distinct GIC IRQs for the LPC subdevices such as
the iBT device. Previously on the AST2400 and AST2500 the LPC subdevices
shared a single LPC IRQ.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-4-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The datasheet says we have 197 IRQs allocated, and we need more than 128
to describe IRQs from LPC devices. Raise the value now to allow
modelling of the LPC devices.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-3-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This appears to be a requirement of the GIC model. The AST2600 allocates
197 GIC IRQs, which we will adjust shortly.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-2-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The ast2600 machines do not have PSCI firmware, so this property should
have never been set. Removing this node fixes SMP booting Linux kernels
that have PSCI enabled, as Linux fails to find PSCI in the device tree
and falls back to the soc-specific method for enabling secondary CPUs.
The comment is out of date as Qemu has supported -kernel booting since
9bb6d14081 ("aspeed: Add boot stub for smp booting"), in v5.1.
Fixes: f25c0ae107 ("aspeed/soc: Add AST2600 support")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210303010505.635621-1-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
There are 23 files that include the "sysemu/qtest.h",
but they do not use any qtest functions.
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210226081414.205946-1-kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Add support for the mps3-an547 board; this is an SSE-300 based
FPGA image that runs on the MPS3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-43-peter.maydell@linaro.org
The AN547 configures the SSE-300 with a different initsvtor0
setting from its default; make this a board-specific setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-42-peter.maydell@linaro.org
The AN547 runs the APB peripherals outside the SSE-300 on a different
and slightly slower clock than it runs the SSE-300 with. Support
making the APB peripheral clock frequency board-specific. (For our
implementation only the UARTs actually take a clock.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-41-peter.maydell@linaro.org
For the AN547 image, the FPGAIO block has an extra DBGCTRL register,
which is used to control the SPNIDEN, SPIDEN, NPIDEN and DBGEN inputs
to the CPU. These signals control when the CPU permits use of the
external debug interface. Our CPU models don't implement the
external debug interface, so we model the register as
reads-as-written.
Implement the register, with a property defining whether it is
present, and allow mps2-tz boards to specify that it is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-39-peter.maydell@linaro.org
The AN547 puts the combined UART overflow IRQ at 48, not 47 like the
other images. Make this setting board-specific.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-37-peter.maydell@linaro.org
Now we have sufficiently parameterised the code, we can add SSE-300
support by adding a new entry to the armsse_variants[] array.
Note that the main watchdog (unlike the s32k watchdog) in the SSE-300
is a different device from the CMSDK watchdog; we don't have a model
of it so we leave it as a TYPE_UNIMPLEMENTED_DEVICE stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-36-peter.maydell@linaro.org
Support SSE variants like the SSE-300 with an ARMSSE_CPU_PWRCTRL register
block. Because this block is per-CPU and does not clash with any of the
SSE-200 devices, we handle it with a has_cpu_pwrctrl flag like the
existing has_cachectrl, has_cpusectrl and has_cpuid, rather than
trying to add per-CPU-device support to the devinfo array handling code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-35-peter.maydell@linaro.org
The SSE-300 has four timers of type TYPE_SSE_TIMER; add support in
the code for having these in an ARMSSEDeviceInfo array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-34-peter.maydell@linaro.org
The SSE-300 has a system counter device; add support for SSE
variants having this device.
As with the existing devices like the cache control block, CPUID
block, etc, we don't try to make the MMIO addresses configurable. We
can do that if and when we need to model a future SSE variant which
has the counter in a different location.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-33-peter.maydell@linaro.org
The SSE-300 has a slightly different set of shared-per-CPU interrupts,
allow the irq_is_common[] array to be different per SSE variant.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-32-peter.maydell@linaro.org
We forgot to implement a TYPE_UNIMPLEMENTED_DEVICE stub
for the SYS_PPU in the SSE-200, which is at 0x50022000.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-31-peter.maydell@linaro.org
Move the PPUs into the data-driven device placement framework.
We don't implement them, so they are just TYPE_UNIMPLEMENTED stubs.
Because the SSE-200 and the IotKit diverge here (the IoTKit does
not have the PPUs) we need to separate out the ARMSSEDeviceInfo
for the two variants, and only add the PPUs to the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-30-peter.maydell@linaro.org
Move the sysctl register block into the data-driven device placement
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-29-peter.maydell@linaro.org
Move the sysinfo register block into the data-driven framework.
While we are moving the code for configuring this device around,
regularize on using &error_abortw when setting the integer
properties: they are all simple DEFINE_PROP_UINT32 properties so the
setting can never fail.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-28-peter.maydell@linaro.org
Move the CMSDK timer that uses the S32K slow clock into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-27-peter.maydell@linaro.org
Move the CMSDK watchdog device handling into the data-driven device
placement framework. This is slightly more complicated because these
devices might wire their IRQs up to the NMI line, and because one of
them uses the slow 32KHz clock rather than the main clock.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-26-peter.maydell@linaro.org
Move the CMSDK dualtimer device handling into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-25-peter.maydell@linaro.org
The SSE-300 is mostly the same as the SSE-200, but it has moved some
of the devices in the memory map and uses different device types in
some cases. To accommodate this, add a framework where the placement
and wiring of some devices can be specified in a data table.
This commit adds the framework for this data-driven device placement,
and makes the CMSDK APB timer devices use it. Subsequent commits
will convert the other devices which differ between SSE-200 and
SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-24-peter.maydell@linaro.org
The SSE uses 32 interrupts for its own devices, and then passes through
its expansion IRQ inputs to the CPU's interrupts 33 and upward.
Add a define for the number of IRQs the SSE uses for itself, instead
of hardcoding 32.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-23-peter.maydell@linaro.org
Convert the apb_ppc0 and apb_ppc1 fields in the ARMSSE state struct
to use an array instead of two separate fields. We already had one
place in the code that wanted to be able to refer to the PPC by
index, and we're about to add more code like that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-22-peter.maydell@linaro.org
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one
instance of this per CPU in the system (so just one for the SSE-300),
and as well as the usual CIDR/PIDR ID registers it has just one
register, CPUPWRCFG. This register allows the guest to configure
behaviour of the system in power-down and deep-sleep states. Since
QEMU does not model those, we make the register a dummy
reads-as-written implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
The ARMSSE_CPUID and ARMSSE_MHU Kconfig stanzas are for the devices
implemented by hw/misc/cpuid.c and hw/misc/armsse-mhu.c. Move them
to hw/misc/Kconfig where they belong.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-20-peter.maydell@linaro.org
The SSE-300 includes some timers which are a different kind to
those in the SSE-200. Model them.
These timers are documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-13-peter.maydell@linaro.org
The SSE-300 includes a counter module; implement a model of it.
This counter is documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-12-peter.maydell@linaro.org
For SSE-300, the SYSINFO register block has two new registers:
* SYS_CONFIG1 indicates the config for a potential CPU2 and CPU3;
since the SSE-300 can only be configured with a single CPU it
is always zero
* IIDR is the subsystem implementation identity register;
its value is set by the SoC integrator, so we plumb this in from
the armsse.c code as we do with SYS_VERSION and SYS_CONFIG
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-11-peter.maydell@linaro.org
In the SSE-300, the format of the SYS_CONFIG0 register has changed again;
pass through the correct value to the SYSINFO register block device.
We drop the old SysConfigFormat enum, which was implemented in the
hope that different flavours of SSE would share the same format;
since they all seem to be different and we now have an sse_version
enum to key off, just use that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-10-peter.maydell@linaro.org
The version of the SYSINFO Register Block in the SSE-300 has
different CIDR/PIDR register values to the SSE-200; pass in
the sse-version property and use it to select the correct
ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-9-peter.maydell@linaro.org
The versions of the Secure Access Configuration Register Block
and Non-secure Access Configuration Register Block in the SSE-300
are the same as those in the SSE-200, but the CIDR/PIDR ID
register values are different.
Plumb through the sse-version property and use it to select
the correct ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-8-peter.maydell@linaro.org
We model Arm "Subsystems for Embedded" SoC subsystems using generic
code which is split into various sub-devices which are configurable
by QOM properties to handle the behaviour differences between the SSE
subsystems we implement. Currently the only sub-device which needs
to change is the IOTKIT_SYSCTL device, and we do this with a mix of
properties that directly specify divergent behaviours (eg
CPUWAIT_RST) and passing it the SYS_VERSION register value as a way
for it to distinguish IoTKit from SSE-200.
The "pass SYS_VERSION" approach is already a bit hacky, since the
IOTKIT_SYSCTL device has to know that the different part of the
register value happens to be bits [31:28]. For SSE-300 this register
is renamed SOC_IDENTITY and has a different format entirely, all of
whose fields can be configured by the SoC integrator when they
integrate the SSE into their SoC, and so "pass SYS_VERSION" breaks
down completely.
Switch to using a simple integer property representing an
internal-to-QEMU enumeration of the SSE flavour. For the moment we
only need this in IOTKIT_SYSCTL, but as we add SSE-300 support a few
of the other devices will also need to know.
We define and permit a value for the SSE-300 so we can start using
it in subsequent commits which add SSE-300 support.
The now-redundant is_sse200 flag in IoTKitSysCtl will be removed
in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-6-peter.maydell@linaro.org
Hao Wu
Andrew Jones
Eric Auger
Edgar E. Iglesias
Peter Maydell
Alex Bennée
Xuzhou Cheng
Andrew Jeffery
Cédric Le Goater
Joel Stanley
Chen Qun