The GICv3 support for virtualization includes an outbound
maintenance interrupt signal which is asserted when the
CPU interface wants to signal to the hypervisor that it
needs attention. Expose this as an outbound GPIO line from
the CPU object which can be wired up as a physical interrupt
line by the board code (as we do already for the CPU timers).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-4-git-send-email-peter.maydell@linaro.org
Augment the GIC's QOM device interface by adding two
new sets of sysbus IRQ lines, to signal VIRQ and VFIQ to
each CPU.
We never use these, but it's helpful to keep the v2-and-earlier
GIC's external interface in line with that of the GICv3 to
avoid board code having to add extra code conditional on which
version of the GIC is in use.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-3-git-send-email-peter.maydell@linaro.org
Augment the GICv3's QOM device interface by adding two
new sets of sysbus IRQ lines, to signal VIRQ and VFIQ to
each CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1483977924-14522-2-git-send-email-peter.maydell@linaro.org
Linux for arm64 v4.10 and later will complain if the ECAM config space is
not reserved in the ACPI namespace:
acpi PNP0A08:00: [Firmware Bug]: ECAM area [mem 0x3f000000-0x3fffffff] not reserved in ACPI namespace
The rationale is that OSes that don't consume the MCFG table should still
be able to infer that the PCI config space MMIO region is occupied.
So update the ACPI table generation routine to add this reservation.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Message-id: 1484328738-21149-1-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Using -cpu cortex-a9 (or any other unsupported CPU) with the virt
board will cause QEMU to segmentation fault. This bug was introduced
in commit 9ac4ef77, which incorrectly added a NULL terminator when
converting the VirtBoardInfo array into a simple array of strings
defining the valid CPUs. The cpuname_valid() loop already has
a termination condition based on ARRAY_SIZE, so the NULL is
spurious and causes the strcmp() to segfault if we reach it.
Delete the NULL.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1484619334-10488-1-git-send-email-zhaoshenglong@huawei.com
[PMM: expanded commit message]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a ROM region, using the default size of the mapping window for
the CE0 FMC flash module, and fill it with the flash content.
This is a little hacky but until we can boot from a MMIO region, it
seems difficult to do anything else.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-11-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SMC controllers have a mode (Command mode) in which
accesses to the flash content are no different than doing MMIOs. The
controller generates all the necessary commands to load (or store)
data in memory.
So add a couple of tests doing direct reads and writes on the AHB bus.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-10-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's make sure when each test is run that the flash object is in an
initial state and did not keep configuration from the previous tests.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1483979087-32663-9-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SMC controllers have a mode (Command mode) in which
accesses to the flash content are no different than doing MMIOs. The
controller generates all the necessary commands to load (or store)
data in memory.
However, accesses are restricted to the segment window assigned the
the flash module by the controller. This window is defined by the
Segment Address Register.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-8-git-send-email-clg@kaod.org
[PMM: Deleted now-unused aspeed_smc_is_usermode() function]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SPI controller of the AST2400 SoC has less registers. So we can
adjust the size of the memory region holding the registers depending
on the controller type. We can also remove the guest_error logging
which is useless as the range of the region is strict enough.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1483979087-32663-7-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is getting difficult to read. Also add a 'has_dma' field for each
controller type.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-6-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On the AST2500 SoC, the FMC controller flash type is fixed to SPI for
CE0 and CE1 and 4BYTE mode is autodetected for CE0.
On the AST2400 SoC, the FMC controller flash type and 4BYTE mode are
strapped with register SCU70. We use the default settings from the
palmetto-bmc machine for now.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change the routines prototype to use a 'AspeedSMCFlash *' instead of
'AspeedSMCState *'. The result will help in making future changes
clearer.
Also change aspeed_smc_update_cs() which uselessly loops on all slave
devices to update their status.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1483979087-32663-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead, we can simply set the irq level when unselecting the slave
devices. This change prepares ground for a subsequent cleanup of the
aspeed_smc_update_cs() routine which uselessly loops on all slaves to
update their status.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1483979087-32663-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is useless as reset will be called later on.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com>
Message-id: 1483979087-32663-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The DBGVCR_EL2 system register is needed to run a 32-bit
EL1 guest under a Linux EL2 64-bit hypervisor. Its only
purpose is to provide AArch64 with access to the state of
the DBGVCR AArch32 register. Since we only have a dummy
DBGVCR, implement a corresponding dummy DBGVCR32_EL2.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
To run a VM in 32-bit EL1 our AArch32 interrupt handling code
needs to be able to cope with VIRQ and VFIQ exceptions.
These behave like IRQ and FIQ except that we don't need to try
to route them to Monitor mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
n25q00 and mt25q01 devices share the same JEDEC ID. The difference
between those two devices is number of dies and one bit in extended
JEDEC bytes. This commit adds proper entry for both devices by
introduction the number of dies and and new 25q00 entries.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-4-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Modern big flash NOR devices consist of more than one die.
Some of them do not support chip erase and instead have a die
erase command that can erase one die only. This commit adds
support for defining the number of dies in the chip, and adds
support for die erase command.
The NOR flash model is not strict, so no option to
disable chip erase has been added.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-3-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some flash chips have additional page program opcode that
takes only 4 byte address. This commit adds support
for such command in Qemu.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20170108083854.5006-2-mar.krzeminski@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The imx25 chip provides 3 i2c buses, but they have all been named
"i2c", which makes it difficult to predict which bus a device will
be connected to when specified on the command line.
This patch addresses the issue by naming the buses uniquely:
i2c-bus.0 i2c-bus.1 i2c-bus.2
Signed-off-by: Alastair D'Silva <alastair@d-silva.org>
Message-id: 20170105043430.3176-2-alastair@au1.ibm.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJYf+trAAoJEDNgw/dBGhJfQIgIAIGOtTwWToFhOR35QSms8JQp
OcuIc2+adMKocB9s4/zhJsvJUu0Sgfh9LhxoALTb2syXzeZETWjDPJdQ8sPR/REQ
MUC2i/GCpTpu5UysAqPbfsG+KShErqnSMcp0qlQO1IRqs734WhEISN34l6KlqSxL
1B3w6NInvLnvpi/VDUDN0Je5TDP2MK2BX0k3TTZdWWcDd/pQZZhzBW44PGDXRkfN
hriYrUr5D3jaje6h3lUB09JtOBdv5oVndyjEjCalh0e5EtVQlGrvQRVYbJEBzO2r
OCj467xfygDxVlqHgU5JiZLkvQXmuUPQrTMQURtHDbbViuE+jXjk+jmZtwDOD3Q=
=CvOE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/artyom/tags/pull-sun4v-20170118' into staging
add OpenSPARC T1 emulation
# gpg: Signature made Wed 18 Jan 2017 22:25:47 GMT
# gpg: using RSA key 0x3360C3F7411A125F
# gpg: Good signature from "Artyom Tarasenko <atar4qemu@gmail.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2AD8 6149 17F4 B2D7 05C0 BB12 3360 C3F7 411A 125F
* remotes/artyom/tags/pull-sun4v-20170118: (30 commits)
target-sparc: fix up niagara machine
target-sparc: move common cpu initialisation routines to sparc64.c
target-sparc: implement sun4v RTC
target-sparc: add ST_BLKINIT_ ASIs for UA2005+ CPUs
target-sparc: store the UA2005 entries in sun4u format
target-sparc: implement UA2005 ASI_MMU (0x21)
target-sparc: add more registers to dump_mmu
target-sparc: implement auto-demapping for UA2005 CPUs
target-sparc: allow 256M sized pages
target-sparc: simplify ultrasparc_tsb_pointer
target-sparc: implement UA2005 TSB Pointers
target-sparc: use SparcV9MMU type for sparc64 I/D-MMUs
target-sparc: replace the last tlb entry when no free entries left
target-sparc: ignore writes to UA2005 CPU mondo queue register
target-sparc: allow priveleged ASIs in hyperprivileged mode
target-sparc: use direct address translation in hyperprivileged mode
target-sparc: fix immediate UA2005 traps
target-sparc: implement UA2005 rdhpstate and wrhpstate instructions
target-sparc: implement UA2005 GL register
target-sparc: implement UA2005 hypervisor traps
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the Niagara stub implementation from sun4u.c and add a machine,
compatible with Legion simulator from the OpenSPARC T1 project.
The machine uses the firmware supplied with the OpenSPARC T1 project,
http://download.oracle.com/technetwork/systems/opensparc/OpenSPARCT1_Arch.1.5.tar.bz2
in the directory S10image/, and is able to boot the supplied Solaris 10 image.
Note that for compatibility with the naming conventions for SPARC machines
the new machine name is lowercase niagara.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
In OpenSPARC T1+ TWINX ASIs in store instructions are aliased
with Block Initializing Store ASIs.
"UltraSPARC T1 Supplement Draft D2.1, 14 May 2007" describes them
in the chapter "5.9 Block Initializing Store ASIs"
Integer stores of all sizes are allowed with these ASIs.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
According to chapter 13.3 of the
UltraSPARC T1 Supplement to the UltraSPARC Architecture 2005,
only the sun4u format is available for data-access loads.
Store UA2005 entries in the sun4u format to simplify processing.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Implement the behavior described in the chapter 13.9.11 of
UltraSPARC T1™ Supplement to the UltraSPARC Architecture 2005:
"If a TLB Data-In replacement is attempted with all TLB
entries locked and valid, the last TLB entry (entry 63) is
replaced."
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Please note that QEMU doesn't impelement Real->Physical address
translation. The "Real Address" is always the "Physical Address".
Suggested-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Accordinf to UA2005, 9.3.3 "Address Space Identifiers",
"In hyperprivileged mode, all instruction fetches and loads and stores with implicit
ASIs use a physical address, regardless of the value of TL".
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
As described in Chapter 5.7.6 of the UltraSPARC Architecture 2005,
outstanding disrupting exceptions that are destined for privileged mode can only
cause a trap when the virtual processor is in nonprivileged or privileged mode and
PSTATE.ie = 1. At all other times, they are held pending.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Peter Maydell
Ard Biesheuvel
Shannon Zhao
Cédric Le Goater
Marcin Krzeminski
Alastair D'Silva
Artyom Tarasenko