For configurations of the pflash_cfi01 device which set it up with a
device-width not equal to the width (ie where we are emulating
multiple narrow flash devices wired up in parallel), we were giving
incorrect values in the CFI data table:
(1) the sector length entry should specify the sector length for a
single device, not the length for the overall collection of
devices
(2) the number of blocks per device must not be divided by the
number of devices because the resulting device size would not
match the overall size
(3) this then means that the overall write block size must be
modified depending on the number of devices because the entry is
per device and when the guest writes into the flash it
calculates the write size by using the CFI entry (write size
per device) multiplied by the number of chips.
(It would alternatively be possible to modify the write
block size in the CFI table (currently hardcoded at 2048) and
leave the overall write block size alone.)
This commit corrects these bugs, and adds a hw-compat property
to retain the old behaviour on 2.8 and earlier versions. (The
only board we have which uses this sort of flash config and
has machine versioning is the "virt" board -- the PC uses a
single flash device and so behaviour is unaffected whether
using old-multiple-chip-handling or not.)
Here is a configuration example from the vexpress board:
VEXPRESS_FLASH_SIZE = 64M
VEXPRESS_FLASH_SECT_SIZE 256K
num-blocks = VEXPRESS_FLASH_SIZE / VEXPRESS_FLASH_SECT_SIZE = 256
sector-length = 256K
width = 4
device-width = 2
The code will fill the CFI entry with the following entries:
num-blocks = 256
sector-length = 128K
writeblock_size = 2048
This results in two chips, each with 256 * 128K = 32M device size and
a write block size of 2048.
A sector erase will be sent to both chips, thus 256K must be erased.
When the guest sends a block write command, it will write 4096 bytes
data at once (2048 per device).
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: cleaned up and expanded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
FAULTMASK must be cleared on return from all
exceptions other than NMI.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-7-git-send-email-peter.maydell@linaro.org
The v7m CONTROL register bit 1 is SPSEL, which indicates
the stack being used. We were storing this information
not in v7m.control but in the separate v7m.other_sp
structure field. Unfortunately, the code handling reads
of the CONTROL register didn't take account of this, and
so if SPSEL was updated by an exception entry or exit then
a subsequent guest read of CONTROL would get the wrong value.
Using a separate structure field doesn't really gain us
anything in efficiency, so drop this unnecessary complexity
in favour of simply storing all the bits in v7m.control.
This is a migration compatibility break for M profile
CPUs only.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-6-git-send-email-peter.maydell@linaro.org
[PMM: rewrote commit message;
use deposit32(); use FIELD to define constants for
masking and shifting of CONTROL register fields
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
hw/register.h provides macros like FIELD which make it easy to define
shift, mask and length constants for the fields within a register.
Unfortunately register.h also includes a lot of other things, some
of which will only compile in the softmmu build.
Pull the FIELD macro and friends out into a separate header file,
so they can be used in places like target/arm files which also
get built in the user-only configs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-5-git-send-email-peter.maydell@linaro.org
Give an explicit error and abort when a load
from the vector table fails. Architecturally this
should HardFault (which will then immediately
fail to load the HardFault vector and go into Lockup).
Since we don't model Lockup, just report this guest
error via cpu_abort(). This is more helpful than the
previous behaviour of reading a zero, which is the
address of the reset stack pointer and not a sensible
location to jump to.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-4-git-send-email-peter.maydell@linaro.org
[PMM: expanded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For v7m we need to catch attempts to execute from special
addresses at 0xfffffff0 and above. Previously we did this
with the aid of a hacky special purpose lump of memory
in the address space and a check in translate.c for whether
we were translating code at those addresses.
We can implement this more cleanly using a CPU
unassigned access handler which throws the exception
if the unassigned access is for one of the special addresses.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484937883-1068-3-git-send-email-peter.maydell@linaro.org
[PMM:
* drop the deletion of the "don't interrupt if PC is magic"
code in arm_v7m_cpu_exec_interrupt() -- this is still
required
* don't generate an exception for unassigned accesses
which aren't to the magic address -- although doing
this is in theory correct in practice it will break
currently working guests which rely on the RAZ/WI
behaviour when they touch devices which we haven't
modelled.
* trigger EXCP_EXCEPTION_EXIT on is_exec, not !is_write
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MRS and MSR instruction handling has a number of flaws:
* unprivileged accesses should only be able to read
CONTROL and the xPSR subfields, and only write APSR
(others RAZ/WI)
* privileged access should not be able to write xPSR
subfields other than APSR
* accesses to unimplemented registers should log as
guest errors, not abort QEMU
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1484937883-1068-2-git-send-email-peter.maydell@linaro.org
[PMM: rewrote commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When doing fast read, a certain amount of dummy bytes should be sent
before the read. This number is configurable in the controler CE0
Control Register and needs to be modeled using fake transfers to the
flash module.
This only supports command mode. User mode requires more work and a
possible extension of the m25p80 device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com>
Message-id: 1484751701-2646-1-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If a QIOTask has an error set and the calling code uses
qio_task_propagate_error() to steal the reference to
that Error object, the task would not clear its own
reference. This would lead to a double-free when
qio_task_free runs, if the caller had (correctly) freed
the Error object they now owned.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
AioHandlers marked ->is_external must be skipped when aio_node_check()
fails. bdrv_drained_begin() needs this to prevent dataplane from
submitting new I/O requests while another thread accesses the device and
relies on it being quiesced.
This patch fixes the following segfault:
Program terminated with signal SIGSEGV, Segmentation fault.
#0 0x00005577f6127dad in bdrv_io_plug (bs=0x5577f7ae52f0) at qemu/block/io.c:2650
2650 bdrv_io_plug(child->bs);
[Current thread is 1 (Thread 0x7ff5c4bd1c80 (LWP 10917))]
(gdb) bt
#0 0x00005577f6127dad in bdrv_io_plug (bs=0x5577f7ae52f0) at qemu/block/io.c:2650
#1 0x00005577f6114363 in blk_io_plug (blk=0x5577f7b8ba20) at qemu/block/block-backend.c:1561
#2 0x00005577f5d4091d in virtio_blk_handle_vq (s=0x5577f9ada030, vq=0x5577f9b3d2a0) at qemu/hw/block/virtio-blk.c:589
#3 0x00005577f5d4240d in virtio_blk_data_plane_handle_output (vdev=0x5577f9ada030, vq=0x5577f9b3d2a0) at qemu/hw/block/dataplane/virtio-blk.c:158
#4 0x00005577f5d88acd in virtio_queue_notify_aio_vq (vq=0x5577f9b3d2a0) at qemu/hw/virtio/virtio.c:1304
#5 0x00005577f5d8aaaf in virtio_queue_host_notifier_aio_poll (opaque=0x5577f9b3d308) at qemu/hw/virtio/virtio.c:2134
#6 0x00005577f60ca077 in run_poll_handlers_once (ctx=0x5577f79ddbb0) at qemu/aio-posix.c:493
#7 0x00005577f60ca268 in try_poll_mode (ctx=0x5577f79ddbb0, blocking=true) at qemu/aio-posix.c:569
#8 0x00005577f60ca331 in aio_poll (ctx=0x5577f79ddbb0, blocking=true) at qemu/aio-posix.c:601
#9 0x00005577f612722a in bdrv_flush (bs=0x5577f7c20970) at qemu/block/io.c:2403
#10 0x00005577f60c1b2d in bdrv_close (bs=0x5577f7c20970) at qemu/block.c:2322
#11 0x00005577f60c20e7 in bdrv_delete (bs=0x5577f7c20970) at qemu/block.c:2465
#12 0x00005577f60c3ecf in bdrv_unref (bs=0x5577f7c20970) at qemu/block.c:3425
#13 0x00005577f60bf951 in bdrv_root_unref_child (child=0x5577f7a2de70) at qemu/block.c:1361
#14 0x00005577f6112162 in blk_remove_bs (blk=0x5577f7b8ba20) at qemu/block/block-backend.c:491
#15 0x00005577f6111b1b in blk_remove_all_bs () at qemu/block/block-backend.c:245
#16 0x00005577f60c1db6 in bdrv_close_all () at qemu/block.c:2382
#17 0x00005577f5e60cca in main (argc=20, argv=0x7ffea6eb8398, envp=0x7ffea6eb8440) at qemu/vl.c:4684
The key thing is that bdrv_close() uses bdrv_drained_begin() and
virtio_queue_host_notifier_aio_poll() must not be called.
Thanks to Fam Zheng <famz@redhat.com> for identifying the root cause of
this crash.
Reported-by: Alberto Garcia <berto@igalia.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Tested-by: Alberto Garcia <berto@igalia.com>
Message-id: 20170124095350.16679-1-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2c21ee7 ("migration: extend VMStateInfo") missed a void -> int
return conversion for kvm_flic_save().
Fixes: 2c21ee7 ("migration: extend VMStateInfo")
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Add calls to hbitmap_is_serializable() (asserting that it returns true)
where necessary (i.e. before every series of (de-)serialization function
invocations).
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20161115225746.3590-3-mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
Bitmaps with a granularity of 58 or above can be neither serialized nor
deserialized (see the comment in the function added in this series for
an explanation). This patch adds a function so that we can check whether
a bitmap actually can be (de-)serialized at all, thus avoiding failing
the necessary assertion in hbitmap_serialization_granularity().
Signed-off-by: Max Reitz <mreitz@redhat.com>
Message-Id: <20161115225746.3590-2-mreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Fam Zheng <famz@redhat.com>
cause 9p clients to hang. Other patches are minor enhancements.
-----BEGIN PGP SIGNATURE-----
iEYEABECAAYFAliIegsACgkQAvw66wEB28LjzwCeIKbBFC/hbc43UqaNX82OGd2v
soYAn0YYXJUAykyjNEMLdhhNp+rABzNk
=1PaE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/gkurz/tags/for-upstream' into staging
This pull request fixes a 2.9 regression and a long standing bug that can
cause 9p clients to hang. Other patches are minor enhancements.
# gpg: Signature made Wed 25 Jan 2017 10:12:27 GMT
# gpg: using DSA key 0x02FC3AEB0101DBC2
# gpg: Good signature from "Greg Kurz <groug@kaod.org>"
# gpg: aka "Greg Kurz <groug@free.fr>"
# gpg: aka "Greg Kurz <gkurz@fr.ibm.com>"
# gpg: aka "Greg Kurz <gkurz@linux.vnet.ibm.com>"
# gpg: aka "Gregory Kurz (Groug) <groug@free.fr>"
# gpg: aka "Gregory Kurz (Cimai Technology) <gkurz@cimai.com>"
# gpg: aka "Gregory Kurz (Meiosys Technology) <gkurz@meiosys.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 2BD4 3B44 535E C0A7 9894 DBA2 02FC 3AEB 0101 DBC2
* remotes/gkurz/tags/for-upstream:
9pfs: fix offset error in v9fs_xattr_read()
9pfs: local: trivial cosmetic fix in pwritev op
9pfs: fix off-by-one error in PDU free list
tests: virtio-9p: improve error reporting
9pfs: add missing coroutine_fn annotations
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current code tries to copy `read_count' bytes starting at offset
`offset' from a `read_count`-sized iovec. This causes v9fs_pack() to
fail with ENOBUFS.
Since the PDU iovec is already partially filled with `offset' bytes,
let's skip them when creating `qiov_full' and have v9fs_pack() to
copy the whole of it. Moreover, this is consistent with the other
places where v9fs_init_qiov_from_pdu() is called.
This fixes commit "bcb8998fac16 9pfs: call v9fs_init_qiov_from_pdu
before v9fs_pack".
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Stefano Stabellini <sstabellini@kernel.org>
The server can handle MAX_REQ - 1 PDUs at a time and the virtio-9p
device has a MAX_REQ sized virtqueue. If the client manages to fill
up the virtqueue, pdu_alloc() will fail and the request won't be
processed without any notice to the client (it actually causes the
linux 9p client to hang).
This has been there since the beginning (commit 9f10751365 "virtio-9p:
Add a virtio 9p device to qemu"), but it needs an agressive workload to
run in the guest to show up.
We actually allocate MAX_REQ PDUs and I see no reason not to link them
all into the free list, so let's fix the init loop.
Reported-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Suggested-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Greg Kurz <groug@kaod.org>
Add remaining bits of the Altera NiosII R1 support into qemu, which
is documentation, MAINTAINERS file entry, configure bits, arch_init
and configuration files for both linux-user (userland binaries) and
softmmu (hardware emulation).
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-8-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Add the Altera 10M50 Nios2 GHRD model. This allows emulating the
10M50 development kit with the Nios2 GHRD loaded in the FPGA. It
is possible to boot Linux kernel and run userspace, thus far only
from initrd as storage support is not yet implemented.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-7-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Add the Altera timer model.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-6-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Add the Altera Nios2 internal interrupt controller model.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-5-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Add missing bits for qemu-user required for emulating Altera Nios2
userspace binaries.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-4-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Add nios2 disassembler support. This patch is composed from binutils files
from commit "Opcodes and assembler support for Nios II R2". The files from
binutils used in this patch are:
include/opcode/nios2.h
include/opcode/nios2r1.h
include/opcode/nios2r2.h
opcodes/nios2-opc.c
opcodes/nios2-dis.c
Checkpatch says total: 114 errors, 0 warnings, 3609 lines checked , which
is caused by a different coding style in those files. These warnings and
errors are not addressed To let these files be easily synchronized between
binutils and qemu.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-2-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Add support for emulating Altera NiosII R1 architecture into qemu.
This patch is based on previous work by Chris Wulff from 2012 and
updated to latest mainline QEMU.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Cc: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-3-marex@denx.de>
[rth: Remove tlb_flush from nios2_cpu_reset.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
It has "bridge" in its name, so it should be in the category
DEVICE_CATEGORY_BRIDGE.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
It's a storage device, so let's classify it accordingly. And
while we're at it, also add a short description for people who
do not know what MTP means.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Some updates from fprintf(stderr, ...) to error_report.
Signed-off-by: Ziyue Yang <skiver.cloud.yzy@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This patch is to fix the segmentation fault caused by attaching
GDB to a QEMU instance initialized with "-M none" option.
The bug can be reproduced by
> ./qemu-system-x86_64 -M none -nographic -S -s
and attach a GDB to it by
> gdb -ex 'target remote :1234
The segmentation fault was originally caused by trying to read
the information about CPU when communicating with GDB. However,
it's impossible for any control flow to exist on an empty machine,
nor can CPU's be hot plugged to an empty machine later by QOM
commands. So I think simply disabling GDB connections on empty
machines makes sense.
Signed-off-by: Ziyue Yang <skiver.cloud.yzy@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Commit 166dbda7e1 added some extra cases to a switch() such
that the existing code is intended to fall through the new
case statements. It's clear from the commit that this is
intentional, but less clear to subsequent readers of the
code, and not clear at all to static analysis tools like
Coverity. Add a /* fall through */ comment to indicate the
intent. (Fixes CID 1368287.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The curses and none possibilities are already documented on a separate line,
so documenting it on the sdl line was both unneeded and confusing.
Introduced in commit f04ec5afbb
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Coverity points out that calculating src_len by multiplying
src_width by rows could overflow. This can only happen in
the implausible case of a framebuffer larger than 4GB, but
we may as well fix it, placating Coverity. (CID1005515)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
A fix has been committed in upstream glib commit
210a9796f78eb90f76f1bd6a304e9fea05e97617.
(See also related bug https://bugzilla.gnome.org/show_bug.cgi?id=764415)
It is desirable to use the glib version instead of qemu copy, since it
provides more debugging facilities (G_MAIN_POLL_DEBUG etc), and
hopefully has a better maintainance. Hopefully, we can drop the qemu
copy in a few years.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
1st mmap returns *ptr* which aligns to host page size,
| size + align |
------------------------------------------
ptr
input param *align* could be 1M, or 2M, or host page size. After
QEMU_ALIGN_UP, offset will >= 0
2nd mmap use flag MAP_FIXED, then it return ptr+offset, or else fail.
If it success, then we will have something like:
| offset | size |
--------------------------------------
ptr ptr1
*ptr1* is what we really want to return, it equals ptr+offset.
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Coverity (CID 1005689) warns that we don't check that
spec_reg_info() returned non-NULL before dereferencing.
Add the check, though as the comment notes this is
a can't-really-happen case because the earlier constraint
matching should have ruled out the "unknown reg" case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Don't truncate the multiplication and do a 64 bit one instead
because the result is stored in a 64 bit variable.
This fixes a similar coverity warning to commit 237a8650d6,
in a similar way, and is the other half of the fix for
coverity CID 1167561.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The patch_hypercalls() function sets up a 'patches'
variable and checks it at the end of the function, but
never modifies it in the middle. Remove this dead code,
which seems to have been present since the function was
added in commit e5ad936b0f in 2012.
(Spotted by Coverity: CID 1005581.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
process_command returns a negative value in case of error. Make this
clear in the "if" statement and fix the strerror argument to flip it
to positive.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
