We ignore the d1 and d2 dividers in the audio PLL, and force them to
1 (register value 0) at probe time. However the comment preceding the
audio PLL definition says we enforce the default value, which is not
the same.
Fix the preceding comment to match what we do in code.
Fixes: b8eb71dcdd ("clk: sunxi-ng: Add A80 CCU")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In commit 2beaa601c8 ("clk: sunxi-ng: Implement minimum for
multipliers"), the multiplier minimums in the set_rate callback
for NM and NKMP style clocks were not updated.
This patch fixes them to match their round_rate callbacks.
Fixes: 2beaa601c8 ("clk: sunxi-ng: Implement minimum for multipliers")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A zero multiplier does not make sense for clocks.
Use 1 as the minimum when a multiplier minimum isn't specified.
Fixes: 2beaa601c8 ("clk: sunxi-ng: Implement minimum for multipliers")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch utilizes the new PLL clk notifier to gate then ungate the
PLL CPU clock after rate changes. This should mitigate the system
hangs observed after the introduction of cpufreq for the A33.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In common PLL designs, changes to the dividers take effect almost
immediately, while changes to the multipliers (implemented as
dividers in the feedback loop) take a few cycles to work into
the feedback loop for the PLL to stablize.
Sometimes when the PLL clock rate is changed, the decrease in the
divider is too much for the decrease in the multiplier to catch up.
The PLL clock rate will spike, and in some cases, might lock up
completely. This is especially the case if the divider changed is
the pre-divider, which affects the reference frequency.
This patch introduces a clk notifier callback that will gate and
then ungate a clk after a rate change, effectively resetting it,
so it continues to work, despite any possible lockups. Care must
be taken to reparent any consumers to other temporary clocks during
the rate change, and that this notifier callback must be the first
to be registered.
This is intended to fix occasional lockups with cpufreq on newer
Allwinner SoCs, such as the A33 and the H3. Previously it was
thought that reparenting the cpu clock away from the PLL while
it stabilized was enough, as this worked quite well on the A31.
On the A33, hangs have been observed after cpufreq was recently
introduced. With the H3, a more thorough test [1] showed that
reparenting alone isn't enough. The system still locks up unless
the dividers are limited to 1.
A hunch was if the PLL was stuck in some unknown state, perhaps
gating then ungating it would bring it back to normal. Tests
done by Icenowy Zheng using Ondrej's test firmware shows this
to be a valid solution.
[1] http://www.spinics.net/lists/arm-kernel/msg552501.html
Reported-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Tested-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ccu-sun9i-a80 driver uses the ccu_mult_ops struct, but unlike the other
users it doesen't select the corresponding Kconfig symbol under which the
struct is compiled in.
This results in the following link error with CONFIG_SUN9I_A80_CCU=y and
CONFIG_SUNXI_CCU_MULT=n:
drivers/built-in.o:(.data+0x2d638): undefined reference to 'ccu_mult_ops'
Fix this by explicitly selecting CONFIG_SUNXI_CCU_MULT like the other
users of the struct.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With CONFIG_RESET_CONTROLLER=n we get the following link error in the
sunxi-ng clk driver:
drivers/built-in.o: In function `sunxi_ccu_probe':
mux-core.c:(.text+0x12fe68): undefined reference to 'reset_controller_register'
mux-core.c:(.text+0x12fe68): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol 'reset_controller_register'
Fix this by adding the appropriate select statement.
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* Protect against holes in onecell_data
* Fix divison by zero and overflow in the mpll driver
* Add audio clock divider driver for i2s clocks
* Add i2s and spdif master clocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJY57jYAAoJEAFRo5MEFpTRgEUQALTIayOZGZHQu+xFe0UMHCkO
HX+jSNn/CLbf+pOexZash/jGEckdWU7jLsrjRottld+duWAt15rT5hI7ZBe9e2kG
uknLGKWpznuxq0BgF7d1rbm2+cjrQG5GKa3yYUKxW1jr62iQRDA2WH2LfJElvNC7
hFELnzF/kaqP+ErWZyEI6TWknUrajpx30XewqknyQ2xDJawoh+YqhEBRLbc8Slh8
JLwU4m7VyK0Wt988LyAbQH9VvvejwrgMZvleVy24z+hKnjgxTlefy6dioKNMchNH
e6FIJ/yDz6YhJaK2a6Kd3ZmouQRXkH8jodVWOfIfQQSDDpuzdHSHJGHh2rwDRvwz
hM2y4Yd05svpMzl9YxqZFhsqHZSZegZhhR+rdhv7u5I96DVY9xPQC2QGK2hroLRU
0pZU7XKL6rlG9lSqGCIGLzD/gIuwBco385MJUzdkRL7AHf79sXuPeyPYHxD2ox/8
u+g1ek7bex/5xkd4/n6umoqbSsURzObu4FH2EUn5fIR9Rd/IRTo10M5eI+OXI/Ok
j5JXi/Tr/wl9MHgf83vHOGbH+cNCkIRl7FEICgSTxHbao8C1kyvZEMTbs9ZO7ahR
oQyRW0SelLY3JzkYX7H1XOLMgQ4XY+gVVKGksdugGjgD+yuGbzPKxtHTTP0AAAWD
IfAQ/VEO01z+EFGDrPBW
=RvtY
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-for-4.12' of git://github.com/BayLibre/clk-meson into clk-next
Pull AmLogic clk driver updates from Jerome Brunet:
2nd Amlogic clock driver update for 4.12:
* Protect against holes in onecell_data
* Fix divison by zero and overflow in the mpll driver
* Add audio clock divider driver for i2s clocks
* Add i2s and spdif master clocks
- meson8: add some new PLLs
- new clocks for Mali
- misc fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Tz8Z
-----END PGP SIGNATURE-----
Merge tag 'amlogic-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into clk-next
Same great taste as the previous pull request, but now with 50% less DT
bikeshedding!
Amlogic clock driver updates for v4.12
- meson8: add some new PLLs
- new clocks for Mali
- misc fixes.
In case there are multiple notify chains for the same clocks (because they
were registered by different users), we need to propagate potential failure
of any single one of them to the caller. Otherwise we eg risk violating the
V/f curve when a notifier is used for DVFS.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
For validation purposes, it's often useful to be able to retrieve the list
of possible parents in userspace. Add a debugfs file for every clock which
has more than 1 possible parent.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Jon Mayo <jmayo@nvidia.com>
[sboyd@codeaurora.org: Remove useless cast from void and extra
newline]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
These should be const.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
It adds zx296718 pll_vga clock for VGA support, so that VGA device can
get required pixel rate from clock driver for different display mode.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The bit 0 of PLL_CFG0 register is not powerdown on zx296718, but part of
of postdiv2 field. The consequence is that functions like hw_to_idx()
and zx_pll_enable() will end up tampering the postdiv2 of the PLL.
Let's fix it by defining pd_bit 0xff which is obviously invalid for a
bit position and having PLL driver check the validity before operating
on the bit.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
To support VOU VGA display driver with different modes, we need to set
flag for a few clocks, so that clk_set_rate() call in VOU driver can get
VGA device desired pixel rate.
While at it, the divider between pll_vga and clk_vga gets corrected, as
it's 1:1 instead of 1:2.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The clock was mapped on CG15 (gpio2_clocks) in the CCRG0 register.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Thus CS2000 datasheet is indicating below, this patch
follows it.
WARNING: All "Reserved" registers must maintain their default
state to ensure proper functional operation.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Fix a typo which caused both vfe0 and vfe1 powerdomains to be
named as vfe0.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Fixes: 7e824d5079 ("clk: qcom: gdsc: Add mmcc gdscs for msm8996 family")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Use a classic polling to test bit ready.
And the shift of the bit ready of LSE & LSI were wrongs.
Fixes: 861adc44d2 ("clk: stm32f4: Add LSI & LSE clocks")
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the redundant check of 'rate' in the if statement of the
'pll_set_rate' function
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Fixes: 5fe225c105 ("clk: iproc: add initial common clock support")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
as well as fixups of the clock-ids on rk3368 timers, which were unused
and completely wrong (more and differently named timers).
Also there is one new clock on rk3328 using the muxgrf type, a fix for
pll enablement which should wait for the pll to lock before continuing,
some more critical clocks and the rename of the rk1108 to rv1108, as the
soc seems to have been using a preliminary name before its actual release.
The plan is to have the driver changes (pinctrl, clk) go through the
respective maintainer trees and once everything landed in mainline do
the rename of the devicetree files. With the dts-include change in the
clock rename, we also keep everything compiling and thus bisectability.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAljY7X0QHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgRKaCACXoa3hjtS3CSqyJZQyMPPQ0Oda7bblrubR
CE4GmuoZTnX/mUENFEmY7R+k0Np7b6ijPgdiFNpeZo0bpXAdi6bNjerG/QdRPV/P
yP9usSk/8Tx/kY7vnSNTve5QiIJDUoWKGY8fn7ped+GmM7Qeb3/QbWR4N/fL4vVD
nSZnKDO7yGMxLqWL0/QzZyiLzXl1ViEkPWFTedMf3cm0A48p8M/K5jinfMvl9I+o
6e2TIsc2zn6vRKuoGhjqcaRxhtRRV9c2O8wVAcA6BLo/kk3pA9ZTU3QJPsqEcN6A
BTbANYfXiQF6i+Xp1YJHcE2lNQ/sWZOTQtLqY9SL5WzMETMTETT5
=In5R
-----END PGP SIGNATURE-----
Merge tag 'v4.12-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull rockchip clk driver updates from Heiko Stuebner:
General rockchip clock changes for 4.12. Contains some new clock-ids
as well as fixups of the clock-ids on rk3368 timers, which were unused
and completely wrong (more and differently named timers).
Also there is one new clock on rk3328 using the muxgrf type, a fix for
pll enablement which should wait for the pll to lock before continuing,
some more critical clocks and the rename of the rk1108 to rv1108, as the
soc seems to have been using a preliminary name before its actual release.
The plan is to have the driver changes (pinctrl, clk) go through the
respective maintainer trees and once everything landed in mainline do
the rename of the devicetree files. With the dts-include change in the
clock rename, we also keep everything compiling and thus bisectability.
* tag 'v4.12-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: add pll_wait_lock for pll_enable
clk: rockchip: rename RK1108 to RV1108
dt-bindings: rk1108-cru: rename RK1108 to RV1108
clk: rockchip: mark some rk3368 core-clks as critical
clk: rockchip: export SCLK_TIMERXX id for timers on rk3368
clk: rockchip: describe clk_gmac using the new muxgrf type on rk3328
clk: rockchip: add clock ids for timer10-15 of RK3368 SoCs
clk: rockchip: fix up rk3368 timer-ids
clk: rockchip: add rk3328 clk_mac2io_ext ID
clk: rockchip: Set "ignore unused" for PMU M0 clocks on rk3399
- Add support for the Clock Pulse Generator / Module Standby and
Software Reset module on revision ES2.0 of the R-Car H3 SoC, which
differs from ES1.x in some areas.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rttL
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Add support for the Clock Pulse Generator / Module Standby and
Software Reset module on revision ES2.0 of the R-Car H3 SoC, which
differs from ES1.x in some areas.
- Add IMR clocks for R-Car H3 and M3-W,
- Add workaround for PLL0/2/4 errata on R-Car H3 ES1.0,
- Small fixes and cleanups.
* tag 'clk-renesas-for-v4.12-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: rcar-gen3-cpg: Add support for RCLK on R-Car H3 ES2.0
clk: renesas: r8a7795: Add support for R-Car H3 ES2.0
clk: renesas: Add r8a7795 ES2.0 CPG Core Clock Definitions
clk: renesas: cpg-mssr: Add support for fixing up clock tables
clk: renesas: rcar-gen3: Add workaround for PLL0/2/4 errata on H3 ES1.0
clk: renesas: rcar-gen3-cpg: Pass mode pins to rcar_gen3_cpg_init()
clk: renesas: r8a7796: Reformat core clock table
clk: renesas: r8a7795: Reformat core clock table
clk: renesas: r8a7796: Correct name of watchdog clock
clk: renesas: r8a7795: Correct name of watchdog clock
clk: renesas: r8a7795: Correct parent clock and sort order for Audio DMACs
clk: renesas: r8a7796: Add IMR clocks
clk: renesas: r8a7795: Add IMR clocks
* 'for-4.12-ti-clk-cleanups' of https://github.com/t-kristo/linux-pm:
clk: ti: convert to use proper register definition for all accesses
clk: ti: dpll44xx: fix clksel register initialization
clk: ti: gate: export gate_clk_ops locally
clk: ti: divider: add driver internal API for parsing divider data
clk: ti: divider: convert TI divider clock to use its own data representation
clk: ti: mux: convert TI mux clock to use its internal data representation
clk: ti: drop unnecessary MEMMAP_ADDRESSING flag
clk: ti: omap4: cleanup unnecessary clock aliases
clk: ti: enforce const types on string arrays
clk: ti: move omap2_init_clk_clkdm under TI clock driver
clk: ti: add clkdm_lookup to the exported functions
clk: ti: use automatic clock alias generation framework
clk: ti: add API for creating aliases automatically for simple clock types
clk: ti: add support for automatic clock alias generation
clk: ti: remove un-used definitions from public clk_hw_omap struct
The debug APB clock is absent in hi6220 driver, so this patch is to add
support for it.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The CLK_NUMBER value of PRCM CCU is wrongly set to (CLK_APB0_PWD + 1),
which prevented the IR mod clock from being set up.
Change it to (CLK_IR + 1) in order to correctly get IR mod set up.
Fixes: cdb8b80b60 ("clk: sunxi-ng: add support for PRCM CCUs")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The first parent of ir clk in PRCM CCU is wrongly written as "osc32K"
instead of "osc32k".
Change it to "osc32k".
Fixes: cdb8b80b60 ("clk: sunxi-ng: add support for PRCM CCUs")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On Meson8b the MPLL parent clock (fixed_pll) has a rate of 2550MHz.
Multiplying this with SDM_DEN results in a value greater than 32bits.
This is not a problem on the 64bit Meson GX SoCs, but it may result in
undefined behavior on the older 32bit Meson8b SoC.
While rate_from_params was only introduced recently to make the math
reusable from _round_rate and _recalc_rate the original bug exists much
longer.
Fixes: 1c50da4f27 ("clk: meson: add mpll support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[as discussed on the ml, use DIV_ROUND_UP_ULL]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
According to the public datasheet all register bits in HHI_MPLL_CNTL7,
HHI_MPLL_CNTL8 and HHI_MPLL_CNTL9 default to zero. On all GX SoCs these
seem to be initialized by the bootloader to some default value.
However, on my Meson8 board they are not initialized, leading to a
division by zero in rate_from_params as the math is:
(parent_rate * SDM_DEN) / ((SDM_DEN * 0) + 0)
According to the datasheet, the minimum n2 value is 4. The rate provided
by the clock when n2 is less than this minimum is unpredictable. In such
case, we report an error.
Although the rate_from_params function was only introduced recently the
original bug has been there for much longer. It was only exposed
recently when the MPLL clocks were added to the Meson8b clock driver.
Fixes: 1c50da4f27 ("clk: meson: add mpll support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This adds the cts_i958 clock to control the clock source of the spdif
output block. This mux is not explicitly mentionned in the documentation
but it is critical to the spdif dai. It is used to select whether the clock
source of the spdif output is cts_amclk (when data are taken from i2s
buffer) or the cts_mclk_i958 (when data are taken from the spdif buffer)
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the spdif master clock also referred as cts_mclk_i958
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the i2s master clock also referred as cts_amclk
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The audio divider needs a specific clock divider driver.
With am mpll parent clock, which is able to provide a fairly precise rate,
the generic divider tends to select low value of the divider. In such case
the quality of the clock is very poor. For the same final rate, maximizing
the audio clock divider value and selecting the corresponding mpll rate
gives better results. This is what this driver aims to acheive. So far, so
good.
Cc: Hendrik v. Raven <hendrik@consetetur.de>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The clock controller is getting more complex and it might be possible, in
the future, to have holes in the clk_hw_onecell_data array. Just make sure
we skip those holes if it ever happens.
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This moves the ICST clock divider helper library from
arch/arm/common to drivers/clk/versatile so it is maintained
with the other clock drivers.
We keep the structure as a helper library intact and do not
fuse it with the clk-icst.c Versatile ICST clock driver: there
may be other users out there that need to use this library for
their clocking, and then it will be helpful to keep the
library contained. (The icst.[c|h] files could just be moved
to drivers/clk/lib or a similar location to share the library.)
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add clock index to clock registration failure message. Clock name
is sometimes not available, when things go really wrong.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DDR1 PLL on the A33 is an oddball amongst the A33 CCU clocks.
It is a clock multiplier, with the effective multiplier in the
range of 12 ~ 255 and no offset between the multiplier value and
the value programmed into the register.
Implement the zero offset and minimum value of 12 for this clock.
Fixes: d05c748bd7 ("clk: sunxi-ng: Add A33 CCU support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CPU cluster PLLs on the A80 are NP clocks that are atypical in two ways:
- The P factor is 1 bit wide, and translates to a /1 or /4 divider.
- The P factor should only be used for output frequencies lower than
288 MHz. The N factor has a lower limit of 12, which likely contributed
to this extra divider.
According to the user manual, the clocks can only go as low as 200 MHz.
The vendor BSP kernel does not even define operating points below 360
MHz for these clocks. The lower end for cpufreq in the vendor kernel is
even higher. The mainline Linux kernel doesn't support cpufreq for the
A80 at the moment. This means the lower frequencies are untested, and
will likely remain unused.
The new sunxi-ng style clocks don't support the quirks listed above.
Instead of trying to work the quirks in for something of little usage,
we re-model the clocks into N-type multipler clocks, with P fixed at 1.
At probe time we check if P is set to 4, and fix it up if needed. This
is highly unlikely though.
Fixes: b8eb71dcdd ("clk: sunxi-ng: Add A80 CCU")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some PLL clocks are N (multiplier) type clocks, or can be simplified
as such. An example of the former is the DDR1 PLL clock on the A33.
An example of the latter is the CPU PLL clock on the A80, in which
the P divider is only used for low frequencies that are of little
use. Both clocks support PLL lock detection.
The mult clock macro implies support for this, but that is not true.
The field is simply discarded. This patch adds proper support for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The clock tree in the Amlogic GXBB and GXL/GXM SoCs is shared, but the GXL/GXM
SoCs embeds a different GP0 PLL, and needs different parameters with a vendor
provided reduced rate table.
This patch adds the GXL GP0 variant, and adds a GXL DT compatible in order
to use the GXL GP0 PLL instead of the GXBB specific one.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-4-git-send-email-narmstrong@baylibre.com
Tha Amlogic GXBB SoC GP0 PLL needs some vendor provided parameters to be
initializated in the the GP0 control registers before configuring the rate
with the rate table provided parameters.
GXBB GP0 PLL tweaks are also selected to respect the vendor init procedure.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-3-git-send-email-narmstrong@baylibre.com
In recent Amlogic GXBB, GXL and GXM SoCs, the GP0 PLL needs some specific
parameters in order to initialize and lock correctly.
This patch adds an optional PARAM table used to initialize the PLL to a
default value with it's parameters in order to achieve to desired frequency.
The GP0 PLL in GXBB, GXL/GXM also needs some tweaks in the initialization
steps, and these are exposed along the PARAM table.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-2-git-send-email-narmstrong@baylibre.com
The Mali is clocked by two identical clock paths behind a glitch free mux
to safely change frequency while running.
The two "mali_0" and "mali_1" clocks are composed of a mux, divider and gate.
Expose these two clocks trees using generic clocks.
Finally the glitch free mux is added as "mali" clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490177935-9646-3-git-send-email-narmstrong@baylibre.com
SoCs after A31 has a clock controller module in the PRCM part.
Support the clock controller module on H3/5 and A64 now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit 8dce89a1c2 ("clk: tegra: Don't warn for PLL defaults
unnecessarily") changed the tegra210_pllcx_set_defaults() function
causing the PLL to always be reset regardless of whether it is in-use.
This function was changed so that resetting of the PLL will only be
skipped if the PLL is enabled AND 'pllcx->params->defaults_set' is not
true. However, the 'pllcx->params->defaults_set' is always true and
hence, the PLL is now always reset. This causes the boot to fail on the
Tegra210 Smaug where the PLL is already enabled and in-use. Fix this by
only resetting the PLL if not in-use and only printing the warning that
the defaults are not set after we have checked the default settings.
Fixes: 8dce89a1c2 ("clk: tegra: Don't warn for PLL defaults unnecessarily")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
iqc1, iqc2, tegra_clk_pll_a_out_adsp, tegra_clk_pll_a_out0_out_adsp, adsp
and adsp neon were not modelled. dp2 wasn't modelled for Tegra210.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Given that externx can only be used as a parent for clk_out_x, it makes
sense to propagate requests to make clk_out_x easier to handle.
Signed-off-by: Alex Frid <afrid@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Starting with R-Car H3 ES2.0, the parent of RCLK is selected using MD28.
Add support for that, but retain the old behavior for R-Car H3 ES1.x and
M3-W ES1.0 using a quirk.
Inspired by a patch by Takeshi Kihara in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
The Clock Pulse Generator / Module Standby and Software Reset module in
R-Car H3 ES2.0 differs from ES1.x in the following areas:
- More core clocks (S0D2, S0D3, S0D6, S0D8, S0D12),
- Different parent clocks for AUDMAC, EtherAVB, FCP, FDP, IMR,
SYS-DMAC, VIN, VSPB, VSPI,
- Removal of modules CSI21, FCPCI, FCPF2, FCPVD3, FCPVI2, FDP1-2,
USB3-IF1, VSPD3, VSPI2,
- Addition of modules EHCI3, HS-USB-IF3, USB-DMAC3-0, USB-DMAC3-1.
The goal is twofold:
1. Support both the ES1.x and ES2.0 SoC revisions in a single binary
for now,
2. Make it clear which code supports ES1.x, so it can easily be
identified and removed later, when production SoCs are deemed
ubiquitous.
This is achieved by:
- Updating the clock tables for the latest revision (ES2.0), but not
removing clocks that only exist on earlier revisions (ES1.x),
- Detecting the SoC revision at runtime using the new soc_device_match()
API, and fixing up the clocks tables to match the actual SoC
revision, by:
- NULLifying core and module clocks of modules that do not exist,
- Reparenting module clocks that have a different parent on ES1.x.
Based on R-Car Gen3 Hardware User's Manual rev. 0.53E.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The same SoC may have different clocks and/or module clock parents,
depending on SoC revision. One option is to use different sets of clock
tables for each SoC revision. However, if the differences are small, it
is much more space-efficient to have a single set of clock tables, and
fix those up at runtime instead.
Hence provide three helpers:
- Two helpers to NULLify core and module clocks that do not exist on
some revisions (NULLified clocks are skipped during the registration
phase),
- One helper to reparent module clocks that have different clock
parents.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Gxbb datasheet says N2 maximum value is 127 but the register field is
9 bits wide, the maximum value should 511.
Test shows value greater than 127, all the way to 511, works well
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-9-jbrunet@baylibre.com
Use read/write operations for the mpll clocks instead of the
read-only ones.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-7-jbrunet@baylibre.com
This patch adds new callbacks to the meson-mpll driver to control
and set the pll rate. For this, we also need to add the enable bit and
sdm enable bit. The corresponding parameters are added to mpll data
structure.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-6-jbrunet@baylibre.com
Until now, there was only 2 dividers and 2 muxes declared for the gxbb
platform. With the ongoing work on various subsystem, including audio,
this is about to change. Use the same approach as gates for dividers and
muxes, putting them in tables to fix the register address at runtime.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-5-jbrunet@baylibre.com
Until now, there was only 1 divider and 1 mux declared for the meson8b
platform. With the ongoing work on various system, including audio, this
is about to change. Use the same approach as gates for dividers and muxes,
putting them in tables to fix the register address at runtime.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-4-jbrunet@baylibre.com
parameter val is not enclosed in parenthesis which is buggy when given an
expression instead of a simple value
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-2-jbrunet@baylibre.com
A few fixes for a bunch of clocks on a few SoCs. The most important one is
probably one that fixes the NKMP clock frequency calculation and could end
up with clocking the CPU frequency to out of bounds rates.
-----BEGIN PGP SIGNATURE-----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=27Fn
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-fixes
Pull Allwinner clock fixes from Maxime Ripard:
A few fixes for a bunch of clocks on a few SoCs. The most important one is
probably one that fixes the NKMP clock frequency calculation and could end
up with clocking the CPU frequency to out of bounds rates.
* tag 'sunxi-clk-fixes-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi-ng: fix recalc_rate formula of NKMP clocks
clk: sunxi-ng: Fix div/mult settings for osc12M on A64
clk: sunxi-ng: sun6i: Fix enable bit offset for hdmi-ddc module clock
clk: sunxi: ccu-sun5i needs nkmp
clk: sunxi-ng: mp: Adjust parent rate for pre-dividers
If pll is power down,when power up pll need wait pll lock.
The reference documents section:
PLL frequency change and lock check
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockchip finally named the SOC as RV1108, so change it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[include rename in rk1108.dtsi to prevent compile errors]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a workaround for errata on R-Car H3 ES1.0, where the PLL0, PLL2, and
PLL4 clock frequencies are off by a factor of two.
Inspired by a patch by Dien Pham in the BSP.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Dien Pham <dien.pham.ry@renesas.com>
Pass the mode pin states from the SoC-specific CPG/MSSR driver to the
R-Car Gen3 CPG driver core, as their state will be needed to make some
core clock configuration decisions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The parent clock of the Audio DMACs is the "ZS" AXI bus clock, which
maps to S3D1 on R-Car H3 ES1.x.
All module clocks must be sorted by clock ID.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
The recent conversion of proper const usage was only partial and didn't
include Tegra20 and Tegra30 support. Fix that up.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is needed to make the JTAG debugging interface work.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
[treding@nvidia.com: add TODO comment]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This will be used by the powergating driver to ensure proper sequencer
state when the SATA domain is powergated.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has 2 special resets which don't follow the normal pattern:
DVCO and ADSP. Add them in this patch.
Changelog:
v2: add DT bindings file
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In normal operation pll_u is under hardware control and has a fixed rate
of 480MHz. Hardware will turn on pll_u on whenever any of the XUSB
powerdomains is on. From a software point of view we model this is if
pll_u is always on using a fixed rate clock. However the bootloader
might or might not have configured pll_u this way. So we will check the
current state of pll_u at boot and reconfigure it if required.
There are 3 possiblities at kernel boot:
1) pll_u is under hardware control: do nothing
2) pll_u is under hardware control and enabled: enable hardware control
3) pll_u is disabled: enable pll_u and enable hardware control
In all cases we also check if UTMIPLL is under hardware control at boot
and configure it for hardware control if that is not the case.
The same is done during SC7 resume.
Thanks to Joseph Lo <josephl@nvidia.com> for bug fixes.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For completeness, also implement this reset framework API for Tegra.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Arto Merilainen <amerilainen@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In case 2 clocks share an enable bit and one of them is enabled by a
driver and the other one is not, CCF will think it's enabled because it
will only look at the HW state. Therefore it will disable the clock and
thus also disable the other clock which was enabled. Solve this by
reading the initial state of the enable bit and incrementing the
refcount if it's set.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Export UTMIPLL IDDQ functions. These will be needed when powergating the
XUSB partition.
Signed-off-by: BH Hsieh <bhsieh@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock clocks the ADSP Cortex-A9.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a super clock type which implements both mux and divider. This is
used for aclk.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has 3 inputs for Digital Microphones (DMICs). Provide the
required clocks for them.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
checkpatch now warns for const ** and expects const * const * to be used
instead. This means we have to update the prototypes and function
declarations to handle this change.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 has 3 DMIC inputs which can be clocked from the recovered clock
of several other audio inputs (eg. i2s0, i2s1, ...). To model this, we
add a 3 new clocks similar to the audio* clocks which handle the same
function for the I2S and SPDIF clocks.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock is used to clock the HDMI CEC interface.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When used as part of fractional ndiv calculations, the current range is
not enough because the denominator of the fraction is multiplied with m.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Return the actually achieved rate in cfg->output_rate rather than just
the requested rate. This is important to make clk_round_rate() return
the correct result.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If the PLL is on, only warn if the defaults are not yet set. Otherwise
be silent.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This clock doesn't actually exist, so remove it.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The parent for afi is actually mselect, not clk_m.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The 2 ISP clocks (ispa and ispb) share a mux/divider control. So model
this as 1 mux/divider clock and child gate clocks.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
pll_a1 was using CLK_RST_CONTROLLER_PLLA1_MISC_0 for IDDQ control rather
than the correct register CLK_RST_CONTROLLER_PLLA1_MISC_1. Also add
pll_a1 to the set of clocks defined for Tegra210.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In commit e66f81bbd7 ("clk: sunxi-ng: Implement factors offsets"), the
final formula of NKMP clocks' recalc_rate is refactored; however, the
refactored formula broke the calculation due to some C language operand
priority problem -- the priority of operand >> is lower than * and /,
makes the formula being parsed as "(parent_rate * n * k) >> (p / m)", but
it should be "(parent_rate * n * k >> p) / m".
Add the pair of parentheses to fix up this issue. This pair of
parentheses used to exist in the old formula.
Fixes: e66f81bbd7 ("clk: sunxi-ng: Implement factors offsets")
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The mult/div for osc12M was previously backwards (giving a 48M rate
for osc12M). Fix it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Expose clock CLKID_RNG0 which is needed for the HW random number generator.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With the newly introduced clk type for muxes in the grf we now can
describe some missing clocks, like the clk_gmac2io and clk_gmac2phy
that selects between clk_mac2io_src and gmac_clkin based on a bit
set in the general register files.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently, TI clock driver uses an encapsulated struct that is cast into
a void pointer to store all register addresses. This can be considered
as rather nasty hackery, and prevents from expanding the register
address field also. Instead, replace all the code to use proper struct
in place for this, which contains all the previously used data.
This patch is rather large as it is touching multiple files, but this
can't be split up as we need to avoid any boot breakage.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
clksel register pointer should be used for the DPLL-MX autoidle handling.
Currently this is not setup at all. Fix by adding proper handling for the
register.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
These are going to be used by the clkctrl support that will be introduced
later.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This can be used from the divider itself, and also from the clkctrl
clocks once this is introduced.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Instead of using the generic clock driver data struct, use one internal
for the TI clock driver itself. This allows modifying the register access
parts in subsequent patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Instead of using the generic clock driver data struct, use one internal
for the TI clock driver itself. This allows modifying the register access
parts in subsequent patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This has been superceded by the usage of ti_clk_ll_ops for now.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cleanup any unnecessary DT_CLK() alias entries from the OMAP4 clock file.
Most of these are now handled dynamically by the driver code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Constant string arrays should use const char * const instead of just
const char *. Change the implementations using these to proper type.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This is not needed outside the driver, so move it inside it and remove
the prototype from the public header also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This API generates clock aliases automatically for simple clock types
(fixed-clock, fixed-factor-clock), so that we don't need to add the data
for these statically into tables. Shall be called from the SoC specific
clock init.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Large portions of the OMAP framework still depend on the support of
having clock aliases in place, so add support functions for generating
these automatically.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The shared uart-pll is on boot a child of the apll that can get changed
by cpu frequency scaling. So move it away to the more stable gpll to
make sure the uart doesn't break on cpu frequency changes.
This turned up during the 4.11 merge-window when commit
6a171b2993 ("serial: 8250_dw: Allow hardware flow control to be used")
added general termios enablement making the uart on rk3036 change
frequency and thus making it susceptible for the frequency scaling issue.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The mux_pll_src_apll_dpll_gpll_usb480m_p parent list was missing a ","
between the 3rd and 4th parent names, making them fall together and thus
lookups fail. Fix that.
Fixes: 5190c08b29 ("clk: rockchip: add clock controller for rk3036")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some drivers use sprintf to build clk connection id names but the clk
core will save those strings and occasionally print them back. Duplicate
the con_id strings instead of fixing all the users.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the IMR[0-3] clocks to the R8A7795 CPG/MSSR driver.
Based on the original (and large) patch by Konstantin Kozhevnikov
<Konstantin.Kozhevnikov@cogentembedded.com>.
Signed-off-by: Konstantin Kozhevnikov <Konstantin.Kozhevnikov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tighten the depends on the various AllWinn SoCs so we don't
inadvertantly get clock drivers when we're not wanting them
like 32 bit SoC clocks for 64 bit configs. Ensure there's
still test coverage though.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner H5 is a SoC that features a design which keeps the peripheral
compatible with H3, so that it have also a CCU like the one on H3 --
only one bus gate/reset is added, and the mmc sample/output phases are
removed because of MMC controller update.
Add its support in our existing H3 CCU driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clock gates have a pre-divider between the source input and the
gate itself. A notable example is the HSIC 12 MHz clock found on the
A83T, which has the 24 MHz main oscillator as its input, and a /2
pre-divider.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The enable bit offset for the hdmi-ddc module clock is wrong. It is
pointing to the main hdmi module clock enable bit.
Reported-by: Bob Ham <rah@settrans.net>
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: stable@vger.kernel.org # 4.9.x-
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A randconfig build ran into this rare link error:
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.1+0x4): undefined reference to `ccu_nkmp_ops'
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.7+0x4): undefined reference to `ccu_nkmp_ops'
This adds the missing 'select'.
Fixes: 5e73761786 ("clk: sunxi-ng: Add sun5i CCU driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The MP style clocks support an mux with pre-dividers. While the driver
correctly accounted for them in the .determine_rate callback, it did
not in the .recalc_rate and .set_rate callbacks.
This means when calculating the factors in the .set_rate callback, they
would be off by a factor of the active pre-divider. Same goes for
reading back the clock rate after it is set.
Cc: stable@vger.kernel.org
Fixes: 2ab836db50 ("clk: sunxi-ng: Add M-P factor clock support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PMU Cortex M0 on rk3399 is intended to be used for things like
DDRFreq transitions, suspend/resume, and other things that are the
purview of ARM Trusted Firmware and not the kernel. As such, the
kernel shouldn't be messing with the clocks. Add CLK_IGNORE_UNUSED to
these clocks.
Without this change, the following was observed on a Chromebook with a
rk3399 (using not-yet-upstream ARM Trusted Firmware code and
not-yet-upstream kernel code based on kernel-4.4):
1. We init the clock framework.
2. We start up "DDRFreq", which causes ATF to occasionally fire up the
M0 for transitions. Each time ATF fires up the M0 it will turn on
these clocks and each time it is done it will turn them off.
3. We finally get to the the part of the kernel that calls
clk_disable_unused() and we disables the clocks.
You can see the race above. Basically everything is fine as long as
ARM Trusted Firmware isn't starting up the M0 at exactly the same time
that the kernel is disabling unused clocks. ...but if the race
happens then we go boom.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
This includes two branches for arm64 dt updates, both following up
on earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the
start of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=A3U6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
This includes two branches for arm64 dt updates, both following up on
earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the start
of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: deconfig: fix the moxart defconfig
ARM: ux500: resume the second core properly
arm64: dts: juno: update definition for programmable replicator
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
ARM64: dts: meson-gxbb-p200: add ADC laddered keys
ARM64: dts: meson: meson-gx: add the SAR ADC
ARM64: dts: meson-gxl: add the pwm_ao_b pin
ARM64: dts: meson-gx: add the missing pwm_AO_ab node
clk: gxbb: fix CLKID_ETH defined twice
ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
clk: gxbb: add the SAR ADC clocks and expose them
dt-bindings: amlogic: Add WeTek boards
ARM64: dts: meson-gxbb: Add support for WeTek Hub and Play
dt-bindings: vendor-prefix: Add wetek vendor prefix
ARM64: dts: meson-gxm: Rename q200 and q201 DT files for consistency
ARM64: dts: meson-gx: Add HDMI HPD/DDC pinctrl nodes
...
to existing clk drivers. The bulk of the work is on Allwinner and
Rockchip SoCs, but there's also an Intel Atom driver in here too.
New Drivers:
- Tegra BPMP firmware
- Hisilicon hi3660 SoCs
- Rockchip rk3328 SoCs
- Intel Atom PMC
- STM32F746
- IDT VersaClock 5P49V5923 and 5P49V5933
- Marvell mv98dx3236 SoCs
- Allwinner V3s SoCs
Removed Drivers:
- Samsung Exynos4415 SoCs
Updates:
- Migrate ABx500 to OF
- Qualcomm IPQ4019 CPU clks and general PLL support
- Qualcomm MSM8974 RPM
- Rockchip non-critical fixes and clk id additions
- Samsung Exynos4412 CPUs
- Socionext UniPhier NAND and eMMC support
- ZTE zx296718 i2s and other audio clks
- Renesas CAN and MSIOF clks for R-Car M3-W
- Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
- TI CDCE913, CDCE937, and CDCE949 clk generators
- Marvell Armada ap806 CPU frequencies
- STM32F4* I2S/SAI support
- Broadcom BCM2835 DSI support
- Allwinner sun5i and A80 conversion to new style clk bindings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=o8o/
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The usual collection of new drivers, non-critical fixes, and updates
to existing clk drivers. The bulk of the work is on Allwinner and
Rockchip SoCs, but there's also an Intel Atom driver in here too.
New Drivers:
- Tegra BPMP firmware
- Hisilicon hi3660 SoCs
- Rockchip rk3328 SoCs
- Intel Atom PMC
- STM32F746
- IDT VersaClock 5P49V5923 and 5P49V5933
- Marvell mv98dx3236 SoCs
- Allwinner V3s SoCs
Removed Drivers:
- Samsung Exynos4415 SoCs
Updates:
- Migrate ABx500 to OF
- Qualcomm IPQ4019 CPU clks and general PLL support
- Qualcomm MSM8974 RPM
- Rockchip non-critical fixes and clk id additions
- Samsung Exynos4412 CPUs
- Socionext UniPhier NAND and eMMC support
- ZTE zx296718 i2s and other audio clks
- Renesas CAN and MSIOF clks for R-Car M3-W
- Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
- TI CDCE913, CDCE937, and CDCE949 clk generators
- Marvell Armada ap806 CPU frequencies
- STM32F4* I2S/SAI support
- Broadcom BCM2835 DSI support
- Allwinner sun5i and A80 conversion to new style clk bindings"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (130 commits)
clk: renesas: mstp: ensure register writes complete
clk: qcom: Do not drop device node twice
clk: mvebu: adjust clock handling for the CP110 system controller
clk: mvebu: Expand mv98dx3236-core-clock support
clk: zte: add i2s clocks for zx296718
clk: sunxi-ng: sun9i-a80: Fix wrong pointer passed to PTR_ERR()
clk: sunxi-ng: select SUNXI_CCU_MULT for sun5i
clk: sunxi-ng: Check kzalloc() for errors and cleanup error path
clk: tegra: Add BPMP clock driver
clk: uniphier: add eMMC clock for LD11 and LD20 SoCs
clk: uniphier: add NAND clock for all UniPhier SoCs
ARM: dts: sun9i: Switch to new clock bindings
clk: sunxi-ng: Add A80 Display Engine CCU
clk: sunxi-ng: Add A80 USB CCU
clk: sunxi-ng: Add A80 CCU
clk: sunxi-ng: Support separately grouped PLL lock status register
clk: sunxi-ng: mux: Get closest parent rate possible with CLK_SET_RATE_PARENT
clk: sunxi-ng: mux: honor CLK_SET_RATE_NO_REPARENT flag
clk: sunxi-ng: mux: Fix determine_rate for mux clocks with pre-dividers
clk: qcom: SDHCI enablement on Nexus 5X / 6P
...
A total of 380 patches this time, mostly adding support for more hardware
in the device tree descriptions. There is not much exciting here for 4.11,
but I've tried my best to condense the information from the pull requests
I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now
gets fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already
supported chips
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP architecture
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero,
all based on Allwinner SoCs
http://linux-sunxi.org/LicheePi_Onehttp://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless
https://beagleboard.org/black-wirelesshttps://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam i.Core
http://www.opossom.com/english/index.htmlhttp://www.savageboard.org/http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ulhttp://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas, qcom,
rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic,
eeprom, mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ucQ/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"A total of 380 patches this time, mostly adding support for more
hardware in the device tree descriptions. There is not much exciting
here for 4.11, but I've tried my best to condense the information from
the pull requests I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now gets
fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3:
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box:
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder:
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points:
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already supported
chips:
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP
architecture:
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of
Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero, all based on
Allwinner SoCs:
http://linux-sunxi.org/LicheePi_Onehttp://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform:
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless:
https://beagleboard.org/black-wirelesshttps://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module:
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam
i.Core:
http://www.opossom.com/english/index.htmlhttp://www.savageboard.org/http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ulhttp://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
- Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas,
qcom, rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic, eeprom,
mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (380 commits)
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
ARM: DTS: Fix register map for virt-capable GIC
dt-bindings: arm,gic: Fix binding example for a virt-capable GIC
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: dts: Add EMAC AXI settings for Arria10
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
ARM: dts: stm32: Add I2C1 support for STM32429 eval board
ARM: dts: stm32: Add I2C1 support for STM32F429 SoC
ARM: dts: stm32: Use clock DT binding definition on stm32f429 family
dt-bindings: mfd: stm32f4: Add missing binding definition
dt-bindings: mfd: stm32f4: Fix STM32F4_X_CLOCK() macro
ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco
ARM: dts: stm32: add Timers driver for stm32f429 MCU
ARM: dts: add the AB8500 sysclk to the device trees
...
When there is no status bit, it is possible for the clock enable/disable
operation to have not completed by the time the driver code resumes
execution. This is due to the fact that write operations are sometimes
queued and delayed internally. Doing a read ensures the write operations
has completed.
Fixes: b6face404f ("ARM: shmobile: r7s72100: add essential clock nodes to dtsi")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
1. Add necessary initial configuration for clocks of display subsystem.
Till now it worked mostly thanks to bootloader.
2. Use macro definitions instead of hard-coded values for pinctrl on Exynos7.
3. Enable USB 3.0 (DWC3) on Exynos7.
-----BEGIN PGP SIGNATURE-----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=02Sx
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Pull "Samsung DeviceTree ARM64 update for v4.11, third round" from Krzysztof Kozłowski:
1. Add necessary initial configuration for clocks of display subsystem.
Till now it worked mostly thanks to bootloader.
2. Use macro definitions instead of hard-coded values for pinctrl on Exynos7.
3. Enable USB 3.0 (DWC3) on Exynos7.
* tag 'samsung-dt64-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (27 commits)
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
clk: samsung: exynos5433: Add data for 250MHz and 278MHz PLL rates
clk: samsung: exynos5433: Add IDs for PHYCLK_MIPIDPHY0_* clocks
arm64: dts: exynos: Add clocks to Exynos5433 LPASS module
arm64: dts: exynos: set LDO7 regulator as always on
arm64: dts: exynos: configure TV path clocks for Ultra HD modes
arm64: dts: exynos: Fix drive strength of sd0_xxx pin definitions
arm64: dts: exynos: Disable pull down for audio pins in Exynos5433 SoCs
arm64: dts: exynos: Add TM2 touchkey node
arm64: dts: exynos: Remove unneeded unit names in Exynos5433 nodes
arm64: dts: exynos: Enable HDMI/TV path on Exynos5433-TM2
arm64: dts: exynos: Add HDMI node to Exynos5433
arm64: dts: exynos: Add DECON_TV node to Exynos5433
arm64: dts: exynos: Fix addresses in node names on Exynos5433
arm64: dts: exynos: Make TM2 and TM2E independent from each other
arm64: dts: exynos: Fix wrong values for ldo23 and ldo25 on TM2/TM2E
...
of_find_node_by_name() drops the reference to a passed device node.
It is not necessary to drop it again, and doing so may result in the
device node being released prematurely.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fixes: ee15faffef ("clk: qcom: common: Add API to register board clocks backwards compatibly")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This commit:
- makes the GOP_DP (bit 9) gatable clock a child clock of the
SD_MMC_GOP (bit 18) clock, as it should have been. The clock for bit
18 was just named SD_MMC, but since it also covers the GOP block, it
is renamed SD_MMC_GOP.
- makes the MG (bit 5) gatable clock a child clock of the MG_CORE
clock (bit 6)
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The initial implementation in commit e120c17a70 ("clk: mvebu: support
for 98DX3236 SoC") hardcoded a fixed value for the main PLL frequency.
Port code from the Marvell supplied Linux kernel to support different
PLL frequencies and provide clock gating support.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The i2s related clock support is missing from the existing zx296718
clock driver. This patch adds it, so that the upstream ZX I2S driver
can work out.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
PTR_ERR should access the value just tested by IS_ERR, otherwise
the wrong error code will be returned.
Fixes: 783ab76ae5 ("clk: sunxi-ng: Add A80 Display Engine CCU")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We get a link error when CCU_MULT is not set with the
newly added driver:
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.17+0x4): undefined reference to `ccu_mult_ops'
drivers/clk/sunxi-ng/ccu-sun5i.o:(.data.__compound_literal.5+0x4): undefined reference to `ccu_mult_ops'
Fixes: 5e73761786 ("clk: sunxi-ng: Add sun5i CCU driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This kzalloc() could fail. Let's bail out with -ENOMEM here
instead of NULL dereferencing. That silences static checkers. We
should also cleanup on the error path even though this function
returning an error probably means the system won't boot.
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This driver uses the services provided by the BPMP firmware driver to
implement a clock driver based on the MRQ_CLK request. This part of the
BPMP ABI provides a means to enumerate and control clocks and should
allow the driver to work on any chip that supports this ABI.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
and making niu (interconnect) clocks critical on rk3288, as
CLK_IGNORE_UNUSED is not enough to keep them running all the time
when more users access particular clock subtrees.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAliRFEMQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgWHMB/0ZQ1p88CmxkN8kiaJBkO8UpmLuRrPivXoH
HiZBN9fvxdR7DcrhQvH8kSt2Ir9h3Rc22TzPWChcwq1io66Bd8BuXkPP/vP9am8J
It0VeERQzyHTLY++DYTsBmQmuaxPRm9cFsxLY5i4vowipjinFj/gDDX6DIg97j2p
r0ytQQhOM47sRhfJSrGFsfXZIa5z5Ty0Qg04ESGmvIllrMUlm9N7+U667qknkYLW
j2T7jWAK2l3RVe9AC7Bf10l7sldzHPHY5MuQ5WiFUWW3OgJyIUKJbD8jythg9i8V
+54LsmX3HkIjS1OiIwECtU1Nv2t8w9RqDRCubzp/Yf+ff+oDL0h3
=VeAF
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rockchip-clk2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull Rockchip clk updates from Heiko Stuebner:
"Non-critical fix for the pclk_edp divider on rk3399, one new
clock-id and making niu (interconnect) clocks critical on
rk3288, as CLK_IGNORE_UNUSED is not enough to keep them running
all the time when more users access particular clock subtrees."
* tag 'v4.11-rockchip-clk2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
clk: rockchip: rk3288: make all niu clocks critical
clk: rockchip: use rk3288 vip_out clock ids
clk: rockchip: add rk3288 vip_out clock id
clk: rockchip: fix the incorrect pclk_edp div width for RK3399
Add clock for the Cadence eMMC controller on LD11/LD20.
For the other SoCs, the clock for the eMMC controller is included
in the MIO/SD control block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add clock line for the Denali NAND controller.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- Support for one new SoC, the V3s
- Convertion of two old SoCs to the new framework, the old sun5i family
and the A80
- A bunch of fixes
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJYkEtDAAoJEBx+YmzsjxAgLl0QAIt0GnG4tXyTsRqrregO8Qbt
UPK/Qs0hOW5VbpPzKDsWPwNGnTbvYy9I/RDnFiMJtEVU7Cj6ttEO4XvEKnaFF0N+
0ux0ATUIrz6p1pbSUTxV0dCfkqcI78+ECLV4Nsvs7pj5RoJVt4Z5gBMAdErrsB+6
q1VYLXIhs5atK1dTgjEWe4VTwaCpNCwoPMgbedOuZMLB0zFRVxtB/JSxlwGHpdoy
vYZqSUgqmDG1WNLKXAiqsa3k9BnSsX/surAfd6mVlk1MauyKzgHKzxkBrvbNjAMR
juaQcSXwkTOm8bRXj7E7NSFFBWiPUJt6dvXCxRJau79k+bYyPduv0UNu7T0a1IjM
lN0PyJcY22m9O9nsoXVSMvU9YJJd91R94UQRpRSQxN1sOLMGVwnCDhQnB5RJhV3p
gRZNZETTT/rP8E3plJJdce5xCsI6FXUT0jYTQW9cWVTcZbhKsntgNoEE4w/tqWIw
dgE/2UzReyBkWzi9OgjKyca+q8zEd6i1w9DqAg3MwwR8K03oS/aKkBaHjgwk/i8x
uiRXxhT5gLFhYOCwz3DmWw3OjwU7uCifyybGKCoxUE7U/3d2AalsTISCm3PX3dxl
RTDPJWKOSfCyzTJNZpHM5MtIKGh/jM4/yUQ3ARXTGyIa9Uxb4DXlEH6gXvrZ4BUA
UsyJ8d19owDqLIBYaE42
=Jkg2
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clk-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Pull Allwinner clock updates from Maxime Ripard:
- Support for one new SoC, the V3s
- Conversion of two old SoCs to the new framework, the old sun5i family
and the A80
- A bunch of fixes
* tag 'sunxi-clk-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (25 commits)
ARM: dts: sun9i: Switch to new clock bindings
clk: sunxi-ng: Add A80 Display Engine CCU
clk: sunxi-ng: Add A80 USB CCU
clk: sunxi-ng: Add A80 CCU
clk: sunxi-ng: Support separately grouped PLL lock status register
clk: sunxi-ng: mux: Get closest parent rate possible with CLK_SET_RATE_PARENT
clk: sunxi-ng: mux: honor CLK_SET_RATE_NO_REPARENT flag
clk: sunxi-ng: mux: Fix determine_rate for mux clocks with pre-dividers
clk: sunxi-ng: a33: Set CLK_SET_RATE_PARENT for the GPU
clk: sunxi-ng: Call divider_round_rate if we only have a single parent
ARM: gr8: Convert to CCU
ARM: sun5i: Convert to CCU
clk: sunxi-ng: Add sun5i CCU driver
clk: sunxi-ng: Implement global pre-divider
clk: sunxi-ng: Implement multiplier maximum
clk: sunxi-ng: mult: Fix minimum in round rate
clk: sunxi-ng: Implement factors offsets
clk: sunxi-ng: multiplier: Add fractional support
clk: sunxi-ng: add support for V3s CCU
dt-bindings: add device binding for the CCU of Allwinner V3s
...
This patch updates dev_pm_opp_find_freq_*() routines to get a reference
to the OPPs returned by them.
Also updates the users of dev_pm_opp_find_freq_*() routines to call
dev_pm_opp_put() after they are done using the OPPs.
As it is guaranteed the that OPPs wouldn't get freed while being used,
the RCU read side locking present with the users isn't required anymore.
Drop it as well.
This patch also updates all users of devfreq_recommended_opp() which was
returning an OPP received from the OPP core.
Note that some of the OPP core routines have gained
rcu_read_{lock|unlock}() calls, as those still use RCU specific APIs
within them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> [Devfreq]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With the A80 SoC, Allwinner grouped and moved some subsystem specific
clock controls to a separate address space, and possibly separate
hardware block.
One such subsystem is the display engine. The main clock control unit
now only has 1 set of bus gate, dram gate, module clock, and reset
control for the entire display subsystem. These feed into a secondary
clock control unit, which has controls for each individual module
of the display pipeline. This block is not documented in the user
manual. Allwinner's kernel was used as the reference.
Add support for the display engine clock controls found on the A80.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the USB clock controls found on the A80.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the main clock unit found in the A80. Some clocks were
not documented in the released user manual, but were found in the
official kernel from Allwinner. These include controls for the I2S,
SPDIF, SATA, and eDP blocks.
Note that on the A80, some subsystems have separate clock controllers
downstream of the main clock unit. These include the MMC, USB, and
display engine subsystems.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Allwinner A80 SoC, the PLL lock status indicators are grouped
together in a separate register, as opposed to being scattered in each
PLL's configuration register.
Add a flag to support this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
If the CLK_SET_RATE_PARENT flag is set, we want to try getting the
closest parent rate.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds support for the CLK_SET_RATE_NO_REPARENT flag to the
mux determine_rate helper, based on examples from clk-composite and
clk-mux.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The determine_rate helper used ccu_mux_helper_adjust_parent_for_prediv()
to adjust the parent_rate to account for pre-dividers, but then passed
the pristine parent clock rate from clk_hw_get_rate() to the round()
callback, thereby ignoring the pre-divider adjustment. In addition,
it was saving the adjusted parent rate back into struct
clk_rate_request.
This patch fixes this by saving the pristine parent clock rate, and
adding a copy that is adjusted and passed to the round() callback.
The pristine copy, if it is the best solution, would be saved back
to struct clk_rate_request.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add missing clock branch to enable onboard storage
for msm899(2/4).
Signed-off-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
- Use CLK_IS_CRITICAL to handle critical clocks,
- Add Reset Control Support for R-Car Gen2 and Gen3, and RZ/G1,
- Add IIC-DVFS clocks for R-Car H3 and M3-W,
- Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WluB
-----END PGP SIGNATURE-----
Merge tag 'clk-renesas-for-v4.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into clk-next
Pull Renesas clk driver updates from Geert Uytterhoeven:
- Use CLK_IS_CRITICAL to handle critical clocks,
- Add Reset Control Support for R-Car Gen2 and Gen3, and RZ/G1,
- Add IIC-DVFS clocks for R-Car H3 and M3-W,
- Minor cleanups.
* tag 'clk-renesas-for-v4.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add IIC-DVFS clock
clk: renesas: r8a7795: Add IIC-DVFS clock
clk: renesas: cpg-mssr: Add support for reset control
clk: renesas: cpg-mssr: Rename cpg_mssr_priv.mstp_lock
clk: renesas: cpg-mssr: Document suitability for RZ/G1
dt-bindings: clock: renesas: cpg-mssr: Document reset control support
clk: renesas: mstp: Reformat cpg_mstp_clock_register() for git diff
clk: renesas: mstp: Make INTC-SYS a critical clock
clk: renesas: cpg-mssr: Migrate to CLK_IS_CRITICAL
CLKID_ETH is define in the dt-bindings but has not be commented out in the
clock driver. Just do it now.
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The 98DX3236, 98DX3336, 98DX4521 and variants have a different TCLK from
the Armada XP (200MHz vs 250MHz). The CPU core clock is fixed at 800MHz.
The clock gating options are a subset of those on the Armada XP.
The core clock divider is different to the Armada XP also.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
These functions are referencing s3c...._clk_regs[], which are marked as
__initdata. When compiling with CONFIG_DEBUG_SECTION_MISMATCH=y, this
produces warnings like
WARNING: vmlinux.o(.text+0x198350):
Section mismatch in reference from the function s3c2410_clk_sleep_init()
to the (unknown reference) .init.data:(unknown)
Mark the s3c...._clk_sleep_init() functions as __init in
order to fix this.
Fixes: ca2e90ac18 ("clk: samsung: add clock controller driver for s3c2412")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Some PLLs might be disabled by default after turning off and then on
a power domain which they belongs to. To avoid configuring a disabled
PLL, add proper code for handling PLL enable/disable.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This patch fixes simple typos in Exynos5433 clocks driver. The SoC name
was referred a few times as '5443' instead of '5433'.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Default clock configuration applied by the bootloader for TM2 and TM2e
boards includes 250MHz and 278MHz rate for DISP PLL clock. To ensure
such configuration for those boards with 'assigned-clock-*' properties,
parameters for those two additional rates are needed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add missing identifiers for phyclk_mipidphy0_bitclkdiv8_phy and
phyclk_mipidphy0_rxclkesc0_phy clocks. Access to those clocks is needed
to setup initial clock configuration for display subsystem in device tree
in order to avoid dependency on the configuration left by the bootloader.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
In order to achieve all the rates asked by the GPU, we might need to change
the parent frequency.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The divider_get_val function that is used in our determine_rate callback
doesn't try to change the parent rate at all, while clk_divider_bestdiv,
used in divider_round_rate, does.
If we have a single parent, call divider_round_rate.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Add optional support for the Reset Control feature of the Renesas Clock
Pulse Generator / Module Standby and Software Reset module on R-Car
Gen2, R-Car Gen3, and RZ/G1 SoCs.
This allows to reset SoC devices using the Reset Controller API.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The spinlock is used to protect Read-Modify-Write register accesses,
which won't be limited to SMSTPCR register accesses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The Renesas CPG/MSSR driver is already in active use for RZ/G1 since
commits c0b2d75d2a ("clk: renesas: cpg-mssr: Add R8A7743 support")
and 9127d54bb8 ("clk: renesas: cpg-mssr: Add R8A7745 support").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
As the function header of cpg_mstp_clock_register() is split in an
unusual way, "git diff" gets confused when changes to the body of
the function are made, and attributes them to the wrong function.
Reformat the function header to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The BayTrail and CherryTrail platforms provide platform clocks
through their Power Management Controller (PMC).
The SoC supports up to 6 clocks (PMC_PLT_CLK[0..5]) with a
frequency of either 19.2 MHz (PLL) or 25 MHz (XTAL) for BayTrail
and a frequency of 19.2 MHz (XTAL) for CherryTrail. These clocks
are available for general system use, where appropriate, and each
have Control & Frequency register fields associated with them.
Port from legacy by Pierre Bossart, integration in clock framework
by Irina Tirdea
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fix Makefile for x86 support, dependency on CONFIG_COMMON_CLK
was not explicit
Fixes: 701190fd74 ('clk: x86: add support for Lynxpoint LPSS clocks')
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In clock driver initialize phase the spinlock is missed to assignment
to struct clkgate_separated, finally there have no locking to protect
exclusive accessing for clock registers.
This bug introduces the console has no output after enable coresight
driver on 96boards Hikey; this is because console using UART3, which
has shared the same register with coresight clock enabling bit. After
applied this patch it can assign lock properly to protect exclusive
accessing, and console can work well after enabled coresight modules.
Fixes: 0aa0c95f74 ("clk: hisilicon: add common clock support")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* clk-ux500:
clk: ux500: Convert ABx500 clocks to use OF probing
clk: ux500: Add device tree bindings for ABx500 clocks
clk: ux500: move AB8500 sysclk over to PRCMU clk driver
These clocks have been broken for a long time unfortunately, a
hurdle of misc problems made them stop working at some point
breaking USB and audio on Ux500.
The platform as such and all "regular" clocks are migrated to
OF/device tree, so let's migrate also this driver.
With this patch and the corresponding DTS fixes, and a bunch
of probe deferral fixes, audio starts working again on Ux500.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The AB8500 sysclk is just another PRCMU-controlled clock, there
is no reason why it should be in the ABx500-controlled part of
the clock implementation. Doing this and the corresponding device
tree changes makes USB work on the Ux500 again.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The MT8135 is a 32-bit SoC, so only propose it on ARM architecture,
not ARM64.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 234d511d8c ("clk: mediatek: Add hardware dependency")
Cc: Andreas Färber <afaerber@suse.de>
Acked-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
If I say "no" to "Clock driver for Mediatek MT2701", I don't want to
be asked individually about each sub-driver. No means no.
Additionally, this driver shouldn't be proposed at all on non-mediatek
builds, unless build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: e986211827 ("clk: mediatek: Add MT2701 clock support")
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: James Liao <jamesjj.liao@mediatek.com>
Cc: Shunli Wang <shunli.wang@mediatek.com>
Cc: Erin Lo <erin.lo@mediatek.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently the divider selection logic blindly divides the parent_rate
by the clk rate and gives the divider value for the divider clocks
which do not have the CLK_SET_RATE_PARENT flag set. Add the clk divider
table parsing to get the closest divider available in the table
provided via Device tree.
The code is pretty much taken from: drivers/clk/clk-divider.c.
and used here to fix up the best divider selection logic.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Once a gdsc is brought in and out of HW control, there is a
power down and up cycle which can take upto 1us. Polling on
the gdsc status immediately after the hw control enable/disable
can mislead software/firmware to belive the gdsc is already either on
or off, while its yet to complete the power cycle.
To avoid this add a 1us delay post a enable/disable of HW control
mode.
Also after the HW control mode is disabled, poll on the status to
check gdsc status reflects its 'on' before force disabling it
in software.
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Fixes: 904bb4f5c7 ("clk: qcom: gdsc: Add support for gdscs with HW control")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
During meson8b clock probe, clk81 register address is fixed twice.
First using the meson8b_clk_gates array, then by directly changing
meson8b_clk81 register.
As a result meson8b_clk81.reg = HHI_MPEG_CLK_CNTL + clk_base + clk_base.
Fixed by just removing the second fixup.
Fixes: e31a1900c1 ("meson: clk: Add support for clock gates")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch enables clocks for STM32F746 boards.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Do not let the entire probe function fail even if some clocks fail
to register. Let's continue with succeeded clocks. This will give
the system more chances to boot and allow us to investigate the
cause of the failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The HHI_SAR_CLK_CNTL contains three SAR ADC specific clocks:
- a mux clock to choose between different ADC reference clocks (this is
2-bit wide, but the datasheet only lists the parents for the first
bit)
- a divider for the input/reference clock
- a gate which enables the ADC clock
Additionally this exposes the ADC core clock (CLKID_SAR_ADC) and
CLKID_SANA (which seems to enable the analog inputs, but unfortunately
there is no documentation for this - we just mimic what the vendor
driver does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Allwinner A10s, A13, R8 and NextThing GR8 are all based on the same
silicon, and all share the same clocks.
However, they're not packaged in the same way, and therefore not all the
controllers are actually available on all these SoCs.
Introduce a clock controller driver for all these SoCs with different
compatibles to take that into account.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clocks have a global pre-divider that applies to all their parents.
Since it might also apply to clocks that have a single parent, this is
merged in the ccu_common structure, unlike the other pre-divider settings
that are tied to a specific index, and thus a specific parent.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some multipliers have a maximum rate that is lower than what the register
width allows to. Add a field in the multiplier structure to allow CCU
driver to set that maximum.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The previous code was always taking 1 as the minimum in it's round_rate
function, ignoring entirely what was set as minimum in the clock
definition.
Make sure that's not the case anymore.
Fixes: 2beaa601c8 ("clk: sunxi-ng: Implement minimum for multipliers")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The factors we've seen so far all had an offset of one. However, on the
earlier Allwinner SoCs, some factors could have no offset at all, meaning
that the value computed to reach the rate we want to use was the one we had
to program in the registers.
Implement an additional field for the factors that can have such an offset
(linears, not based on a power of two) to specify that offset.
This offset is not linked to the extremums that can be specified in those
structures too. The minimum and maximum are representing the range of
values we can use to try to compute the best rate. The offset comes later
on when we want to set the best value in the registers.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some clocks on the earlier SoCs such as the video PLLs are multipliers with
fractional settings.
Support those cases.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
INTC-SYS is the module clock for the GIC. Accessing the GIC while it is
disabled causes:
Unhandled fault: asynchronous external abort (0x1211) at 0x00000000
Currently, the GIC-400 driver cannot enable its module clock for several
reasons:
- It does not use a platform device, so Runtime PM is not an option,
- gic_of_init() runs before any clocks are registered, so it cannot
enable the clock explicitly,
- gic_of_init() cannot return -EPROBE_DEFER, as IRQCHIP_DECLARE()
doesn't support deferred probing.
Hence we have to keep on relying on the boot loader for enabling the
module clock.
To prevent the module clock from being disabled when the CCF core thinks
it is unused, and thus causing a system lock-up, add a check to the MSTP
clock driver and enable CLK_IS_CRITICAL. This will make sure the module
clock is never disabled.
This is a hard dependency for describing the INTC-SYS clock in DT on
R-Mobile APE6 and R-Car Gen2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
When the Renesas CPG/MSSR driver was introduced, it was anticipated that
critical clocks would be handled through a new CLK_ENABLE_HAND_OFF flag
soon. However, CLK_ENABLE_HAND_OFF never made it upstream.
Instead, commit 32b9b10961 ("clk: Allow clocks to be marked as
CRITICAL") introduced CLK_IS_CRITICAL, a flag with slightly differing
semantics. Still, it can be used to prevent e.g. the GIC module clock
from being turned off, until the GIC-400 driver has full support for
Runtime PM.
Hence migrate the Renesas CPG/MSSR driver from CLK_ENABLE_HAND_OFF to
CLK_IS_CRITICAL.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
NIU clocks are related to the interconnect and it's important to other blocks.
Since we don't have a driver to handle it, we should always enable it to avoid
casually close.
Make all of them critical,so that we don't have to each clock on its own
once things break.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
[dropped the matching CLK_IGNORE_UNUSED flags]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reference the newly added vip clock-ids in the clock-tree.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
caused some of these clocks to turn off when they were always left
on before.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0KLk
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"One fix for Samsung Exynos524x SoCs where recent IOMMU patches have
caused some of these clocks to turn off when they were always left on
before"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk/samsung: exynos542x: mark some clocks as critical
Add the OCOTP so that this hardware block can be used.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This proved incredibly useful during debugging of the DSI driver, to
see if our clocks were running at rate we requested. Let's leave it
here for the next person interacting with clocks on the platform (and
so that hopefully we can just hook it up to debugfs some day).
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The DSI pixel clocks are muxed from clocks generated in the analog phy
by the DSI driver. In order to set them as parents, we need to do the
same name lookup dance on them as we do for our root oscillator.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Our core PLLs are intended to be configured once and left alone. With
the SET_RATE_PARENT, asking to set the PLLD_DSI1 clock rate would
change PLLD just to get closer to the requested DSI clock, thus
changing PLLD_PER, the UART and ethernet PHY clock rates downstream of
it, and breaking ethernet.
We *do* want PLLH to change so that PLLH_AUX can be exactly the value
we want, though. Thus, we need to have a per-divider policy of
whether to pass rate changes up.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These
chips have two clock inputs, XTAL or CLK, which are muxed into single
PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip
while the 5P49V5923 requires external XTAL.
The PLL feeds two fractional dividers. Each fractional divider feeds
output mux, which allows selecting between clock from the fractional
divider itself or from output mux on output N-1. In case of output
mux 0, the output N-1 is instead connected to the output from the mux
feeding the PLL.
The driver thus far supports only the 5P49V5923 and 5P49V5933, while
it should be easily extensible to the whole 5P49V59xx family of chips
as they are all pretty similar.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
controlled through the General Register Files, support for the rk3328
clock-controller (including a new pll-type) and the usual clock ids and
some fixes.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlh+vFMQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgf7TCACncJmYlvYp+aZEgBlEcyCTulHNSyRZHVPd
c4zBsgZmgxqmgrxe8YsW6DcfPP96MtL/C/fIupxTphxxfAS5HQx2KCeVpOrfffk7
lJ1CPyCP5GdjaZ98hKVuMpKVkQu1u26DTNWSy62hbSQQndbpP0NbGsIJJUFia1vm
JX0POVYt0xSo6GnbVRcKN/5b9k0HJNG9aejL8u/uA3+yr8diiKzYrtnaFzai5kvE
3LgXIDGPUZVfwZ2vrJfDCYqNlij/tF2yLIhEDDoMSl00WolJfmnMKOg1Lt0DzuMz
OQY6ZIexTV1CCV+9BjXMVCLth7DH7K3EztQsvyJtr90wrfYs+4Vd
=4WOJ
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into clk-next
Pull Rockchip clk updates from Heiko Stuebner:
A new clock-type for the 1-2 muxes per soc that are for whatever reason
controlled through the General Register Files, support for the rk3328
clock-controller (including a new pll-type) and the usual clock ids and
some fixes.
* tag 'v4.11-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: clk: add rockchip,grf property for RK3399
clk: rockchip: use clock ids for memory controller parts on rk3066/rk3188
clk: rockchip: use rk3288 isp_in clock ids
clk: rockchip: add clock ids for memory controller parts on rk3066/rk3188
clk: rockchip: add rk3288 isp_in clock ids
clk: rockchip: Remove useless init of "grf" to -EPROBE_DEFER
clk: rockchip: add clock controller for rk3328
dt-bindings: add bindings for rk3328 clock controller
clk: rockchip: add dt-binding header for rk3328
clk: rockchip: add new pll-type for rk3328
clk: rockchip: describe aclk_vcodec using the new muxgrf type on rk3288
clk: rockchip: add a clock-type for muxes based in the grf
- addition of the CPU clock configuration data for Exynos4412
Prime SoC variant,
- removal of driver for deprecated Exynos4415 SoC,
- switching from the syscore to regular system sleep PM ops
in the audio subsystem clocks controller driver,
- updates of the definitions of some "Network On Chip" related
clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mSQz
-----END PGP SIGNATURE-----
Merge tag 'clk-v4.11-samsung' of git://linuxtv.org/snawrocki/samsung into clk-next
Pull Samsung clk updates from Sylwester Nawrocki:
- addition of the CPU clock configuration data for Exynos4412
Prime SoC variant,
- removal of driver for deprecated Exynos4415 SoC,
- switching from the syscore to regular system sleep PM ops
in the audio subsystem clocks controller driver,
- updates of the definitions of some "Network On Chip" related
clocks.
* tag 'clk-v4.11-samsung' of git://linuxtv.org/snawrocki/samsung:
clk: samsung: Remove Exynos4415 driver (SoC not supported anymore)
clk: samsung: exynos-audss: Replace syscore PM with platform device PM
clk: samsung: exynos5433: Set NoC (Network On Chip) clocks as critical
clk: samsung: Add CPU clk configuration data for Exynos4412 Prime
The LDB mux/gate layout has been fixed on QuadPlus, so there is no need
to restrict the LDB mux changes on this hardware, as the erratum
preventing this from working properly is gone.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
V3s has a similar but cut-down CCU to H3. Some muxes, especially clocks
about CSI, are different, which makes it to need a new CCU driver.
Add such a new driver for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Export HDMI clock from internal to dt-bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The range of the pclk_edp_div_con is [13:8] and 6 bits, not 5.
Reported-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Tested-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The audio DAI needs to set the clock rates of the ac-dig clock.
To make it possible, the parent PLL audio clock rates should
also be changed. This is possible via "CLK_SET_RATE_PARENT" flag.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
1. Fixes for initial audio clocks configuration.
2. Enable sound on Odroid-X board.
3. Enable DMA for UART modules on Exynos5 SoCs.
4. Add CPU OPPs for Exynos4412 Prime (newer version of Exynos4412). This pulls
necessary change in the clocks.
5. Remove Exynos4212. We do not have any mainline boards with it. This will
simplify few bits later.
-----BEGIN PGP SIGNATURE-----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=w/rg
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree update for v4.11:
1. Fixes for initial audio clocks configuration.
2. Enable sound on Odroid-X board.
3. Enable DMA for UART modules on Exynos5 SoCs.
4. Add CPU OPPs for Exynos4412 Prime (newer version of Exynos4412). This pulls
necessary change in the clocks.
5. Remove Exynos4212. We do not have any mainline boards with it. This will
simplify few bits later.
* tag 'samsung-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: remove Exynos4212 support (dead code)
ARM: dts: exynos: Add CPU OPPs for Exynos4412 Prime
clk: samsung: Add CPU clk configuration data for Exynos4412 Prime
ARM: dts: exynos: Enable DMA support for UART modules on Exynos5 SoCs
ARM: dts: exynos: Cleanup Odroid-X2 and enable sound on Odroid-X
ARM: dts: exynos: Fix initial audio clocks configuration on Exynos4 boards
ARM: dts: exynos: Correct clocks for Exynos4 I2S module
Signed-off-by: Olof Johansson <olof@lixom.net>
Support for Exynos4415 is going away because there are no internal nor
external users.
Since commit 46dcf0ff0d ("ARM: dts: exynos: Remove exynos4415.dtsi"),
the platform cannot be instantiated so remove also the drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add the newly added clock ids to the clock entries of the rk3066/rk3188
clock driver. We won't be needing them in the kernel for a bit yet
but as they're used in the new u-boot ddr setup code/dts we should make
sure the clock ids stay identical and do not differ.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reference the newly added isp clock-ids in the clock-tree.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The failure path in the newly added function tries to free an
uninitialized pointer:
drivers/clk/clk-stm32f4.c: In function 'stm32f4_rcc_init':
drivers/clk/clk-stm32f4.c:1106:4: error: 'gate' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I'm adding an initialization to NULL here to make the kfree()
succeed, and I'm also rearranging the cleanup so that the
same kfree() is used for any error path, making the function
slightly more robust against newly introduced bugs in the
error handling.
Fixes: daf2d117cb ("clk: stm32f4: Add lcd-tft clock")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The CDCE925 is a member of the CDCE(L)9xx programmable clock generator
family. There are also CDCE913, CDCE937, CDCE949 which have different
number of PLLs and outputs.
The clk-cdce925 driver supports only CDCE925 in the family. This adds
support for the CDCE913, CDCE937, CDCE949, too.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add definition of EBI2 clock used by MDM9615 NAND controller.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-soc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Zoran Markovic <zmarkovic@sierrawireless.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[sboyd@codeaurora.org: ebi2_clk halt bit is 24 not 23]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This include was needed to suppress build error when this driver
was initially merged because <linux/regmap.h> did not include
<linux/delay.h> at that time. (developers' headache across
sub-systems)
The root cause has been fixed by commit adf08d481b ("regmap:
include <linux/delay.h> from include/linux/regmap.h"), so this
line can be dropped now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This commit adjusts the list of possible "Sample At Reset" values that
define the CPU clock frequency of the AP806 (part of Marvell Armada
7K/8K) to the values that have been validated with the production
chip. Earlier values were preliminary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add clock drivers for hi3660 SoC, this driver controls the SoC
registers to supply different clocks to different IPs in the SoC.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[sboyd@codeaurora.org: Simplify probe with function pointer]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Some parent clocks of the Exynos542x clock blocks, which have separate
power domains (like DISP, MFC, MSC, GSC, FSYS and G2D) must be always
enabled to access any register related to power management unit or devices
connected to it. For the time being, until a proper solution based on
runtime PM is applied, mark those clocks as critical (instead of ignore
unused or even no flags) to prevent disabling them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> [Exynos5800 Peach Pi Chromebook]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
EPROBE_DEFER is not an error, hence printing an error message like
clk: couldn't get clock 0 for /soc/display@feb00000
may confuse the user.
Suppress error messages in case of probe deferral to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Currently we add the virtual cpufreq device unconditionally even when
the SCPI DVFS clock provider node is disabled. This will cause cpufreq
driver to throw errors when it gets initailised on boot/modprobe and
also when the CPUs are hot-plugged back in.
This patch fixes the issue by adding the virtual cpufreq device only if
the SCPI DVFS clock provider is available and registered.
Fixes: 9490f01e24 ("clk: scpi: add support for cpufreq virtual device")
Reported-by: Michał Zegan <webczat_200@poczta.onet.pl>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Michał Zegan <webczat_200@poczta.onet.pl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support to use reset control framework for resetting MSS
with hexagon v56 1.5.0.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The audio related clock support is missing from the existing zx296718
clock driver. Let's add it, so that the upstream ZX SPDIF driver can
work for HDMI audio support.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[sboyd@codeaurora.org: Staticize some more structures]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Instead of using panic, we should give an error message and return error
code when of_clk_add_hw_provider() call fails.
Since we have error prompt for failures, the "init over" pr_info output
isn't really necessary but becomes a debug noise. So let's clean it up
along the way.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The delay here is not in atomic context and does not seem critical with
respect to precision, but usleep_range(min,max) with min==max results in
giving the timer subsystem no room to optimize uncritical delays. Fix
this by setting the range to 2000,3000 us.
Fixes: commit f05259a6ff ("clk: wm831x: Add initial WM831x clock driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On vf610, PLL1 and PLL2 have registers to configure fractional part of
frequency multiplier.
This patch adds support for these registers.
This fixes "fast system clock" issue on boards where bootloader sets
fractional multiplier for PLL1.
Suggested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
CC: Chris Healy <cphealy@gmail.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
turn all the clks on and another fix for stm32f4 SoCs where we have multiple
drivers attaching to the same DT node.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5ciP
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"One fix for a broken driver on Renesas RZ/A1 SoCs with bootloaders
that don't turn all the clks on and another fix for stm32f4 SoCs where
we have multiple drivers attaching to the same DT node"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: stm32f4: Use CLK_OF_DECLARE_DRIVER initialization method
clk: renesas: mstp: Support 8-bit registers for r7s72100
When we used to defer setting the "grf" member to
rockchip_clk_get_grf() it was important to init the "grf" member to an
error value in rockchip_clk_init(). With recent changes, we now set
"grf" right in rockchip_clk_init() (two lines below the place where we
initted it). That makes the old init useless. Get rid of it.
Fixes: 6f339dc271 ("clk: rockchip: lookup General Register Files in rockchip_clk_init")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the clock tree definition for the new rk3328 SoC.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As the SPDIF was rarely documented on the earlier Allwinner SoCs
it was assumed that it had a similar clock register to the one
described in the H3 User Manual.
However this is not the case and it looks to shares the same setup
as the I2S clock registers.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CPUX clock on A33, which is for the Cortex-A7 cores, is designed to
be changeable by changing the rate of PLL_CPUX.
Add CLK_SET_RATE_PARENT flag to this clock.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When adjusting PLL_CPUX on A33, the PLL is temporarily driven too high,
and the system hangs.
Add a notifier to avoid this situation by temporarily switching to a
known stable 24 MHz oscillator.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When adjusting PLL_CPUX on H3, the PLL is temporarily driven
too high, and the system becomes unstable (oopses or hangs).
Add a notifier to avoid this situation by temporarily switching
to a known stable 24 MHz oscillator.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Tested-by: Lutz Sammer <johns98@gmx.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The rk3328's pll and clock are similar with rk3036's,
it different with pll_mode_mask, the rk3328 soc
pll mode only one bit(rk3036 soc have two bits)
so these should be independent and separate from
the series of rk3328s.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the newly introduced clk type for muxes in the grf we now can
describe some missing clocks, like the aclk_vcodec that selects between
aclk_vdpu and aclk_vepu based on a bit set in the general register files.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Rockchip socs often have some tiny number of muxes not controlled from
the core clock controller but through bits set in the general register
files. Add a clock-type that can control these as well, so that we
don't need to work around them being absent.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Exynos AUDSS clock driver has been already converted to platform driver,
so remove the dependency on the syscore ops - the last remaining
non-platform driver feature. Platform device's system sleep PM provides
all needed infrastructure for replacing syscore-based PM, so do it now.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
The ACLK_BUS0/1/2 are used for NoC (Network on Chip). If NoC's clocks are
disabled, the system halt happens. Following clocks must be always enabled:
- CLK_ACLK_BUS0_400 : NoC's bus clock for PERIC/PERIS/FSYS/MSCL,
- CLK_ACLK_BUS1_400 : NoC's bus clock for MFC/HEVC/G3D,
- CLK_ACLK_BUS2_400 : NoC's bus clock for GSCL/DISP/G2D/CAM0/CAM1/ISP.
This patch also adds the CLK_SET_RATE_PARENT flag to the CLK_SCLK_JPEG_MSCL
because this clock should be used for bus frequency scaling. This clock need
to be changed on the fly with CLK_SET_RATE_PARENT flag.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Add cpu clock configuration data for Exynos4412 Prime SoC
(it supports additional PLL rates & CPU frequencies).
Based on Hardkernel's kernel for ODROID-X2/U2/U3 boards.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>