There are some coding convention warnings in xlnx-zynqmp.c and
xlnx-zynqmp.h, as reported by:
$ ./scripts/checkpatch.pl include/hw/arm/xlnx-zynqmp.h
$ ./scripts/checkpatch.pl hw/arm/xlnx-zynqmp.c
Let's clean them up.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the mps3-an547 board; this is an SSE-300 based
FPGA image that runs on the MPS3.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-43-peter.maydell@linaro.org
The AN547 configures the SSE-300 with a different initsvtor0
setting from its default; make this a board-specific setting.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-42-peter.maydell@linaro.org
The AN547 runs the APB peripherals outside the SSE-300 on a different
and slightly slower clock than it runs the SSE-300 with. Support
making the APB peripheral clock frequency board-specific. (For our
implementation only the UARTs actually take a clock.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-41-peter.maydell@linaro.org
For the AN547 image, the FPGAIO block has an extra DBGCTRL register,
which is used to control the SPNIDEN, SPIDEN, NPIDEN and DBGEN inputs
to the CPU. These signals control when the CPU permits use of the
external debug interface. Our CPU models don't implement the
external debug interface, so we model the register as
reads-as-written.
Implement the register, with a property defining whether it is
present, and allow mps2-tz boards to specify that it is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-39-peter.maydell@linaro.org
The AN547 puts the combined UART overflow IRQ at 48, not 47 like the
other images. Make this setting board-specific.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-37-peter.maydell@linaro.org
Now we have sufficiently parameterised the code, we can add SSE-300
support by adding a new entry to the armsse_variants[] array.
Note that the main watchdog (unlike the s32k watchdog) in the SSE-300
is a different device from the CMSDK watchdog; we don't have a model
of it so we leave it as a TYPE_UNIMPLEMENTED_DEVICE stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-36-peter.maydell@linaro.org
Support SSE variants like the SSE-300 with an ARMSSE_CPU_PWRCTRL register
block. Because this block is per-CPU and does not clash with any of the
SSE-200 devices, we handle it with a has_cpu_pwrctrl flag like the
existing has_cachectrl, has_cpusectrl and has_cpuid, rather than
trying to add per-CPU-device support to the devinfo array handling code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-35-peter.maydell@linaro.org
The SSE-300 has four timers of type TYPE_SSE_TIMER; add support in
the code for having these in an ARMSSEDeviceInfo array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-34-peter.maydell@linaro.org
The SSE-300 has a system counter device; add support for SSE
variants having this device.
As with the existing devices like the cache control block, CPUID
block, etc, we don't try to make the MMIO addresses configurable. We
can do that if and when we need to model a future SSE variant which
has the counter in a different location.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-33-peter.maydell@linaro.org
The SSE-300 has a slightly different set of shared-per-CPU interrupts,
allow the irq_is_common[] array to be different per SSE variant.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-32-peter.maydell@linaro.org
We forgot to implement a TYPE_UNIMPLEMENTED_DEVICE stub
for the SYS_PPU in the SSE-200, which is at 0x50022000.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-31-peter.maydell@linaro.org
Move the PPUs into the data-driven device placement framework.
We don't implement them, so they are just TYPE_UNIMPLEMENTED stubs.
Because the SSE-200 and the IotKit diverge here (the IoTKit does
not have the PPUs) we need to separate out the ARMSSEDeviceInfo
for the two variants, and only add the PPUs to the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-30-peter.maydell@linaro.org
Move the sysctl register block into the data-driven device placement
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-29-peter.maydell@linaro.org
Move the sysinfo register block into the data-driven framework.
While we are moving the code for configuring this device around,
regularize on using &error_abortw when setting the integer
properties: they are all simple DEFINE_PROP_UINT32 properties so the
setting can never fail.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-28-peter.maydell@linaro.org
Move the CMSDK timer that uses the S32K slow clock into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-27-peter.maydell@linaro.org
Move the CMSDK watchdog device handling into the data-driven device
placement framework. This is slightly more complicated because these
devices might wire their IRQs up to the NMI line, and because one of
them uses the slow 32KHz clock rather than the main clock.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-26-peter.maydell@linaro.org
Move the CMSDK dualtimer device handling into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-25-peter.maydell@linaro.org
The SSE-300 is mostly the same as the SSE-200, but it has moved some
of the devices in the memory map and uses different device types in
some cases. To accommodate this, add a framework where the placement
and wiring of some devices can be specified in a data table.
This commit adds the framework for this data-driven device placement,
and makes the CMSDK APB timer devices use it. Subsequent commits
will convert the other devices which differ between SSE-200 and
SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-24-peter.maydell@linaro.org
The SSE uses 32 interrupts for its own devices, and then passes through
its expansion IRQ inputs to the CPU's interrupts 33 and upward.
Add a define for the number of IRQs the SSE uses for itself, instead
of hardcoding 32.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-23-peter.maydell@linaro.org
Convert the apb_ppc0 and apb_ppc1 fields in the ARMSSE state struct
to use an array instead of two separate fields. We already had one
place in the code that wanted to be able to refer to the PPC by
index, and we're about to add more code like that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-22-peter.maydell@linaro.org
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one
instance of this per CPU in the system (so just one for the SSE-300),
and as well as the usual CIDR/PIDR ID registers it has just one
register, CPUPWRCFG. This register allows the guest to configure
behaviour of the system in power-down and deep-sleep states. Since
QEMU does not model those, we make the register a dummy
reads-as-written implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
The ARMSSE_CPUID and ARMSSE_MHU Kconfig stanzas are for the devices
implemented by hw/misc/cpuid.c and hw/misc/armsse-mhu.c. Move them
to hw/misc/Kconfig where they belong.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-20-peter.maydell@linaro.org
The SSE-300 includes some timers which are a different kind to
those in the SSE-200. Model them.
These timers are documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-13-peter.maydell@linaro.org
The SSE-300 includes a counter module; implement a model of it.
This counter is documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-12-peter.maydell@linaro.org
For SSE-300, the SYSINFO register block has two new registers:
* SYS_CONFIG1 indicates the config for a potential CPU2 and CPU3;
since the SSE-300 can only be configured with a single CPU it
is always zero
* IIDR is the subsystem implementation identity register;
its value is set by the SoC integrator, so we plumb this in from
the armsse.c code as we do with SYS_VERSION and SYS_CONFIG
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-11-peter.maydell@linaro.org
In the SSE-300, the format of the SYS_CONFIG0 register has changed again;
pass through the correct value to the SYSINFO register block device.
We drop the old SysConfigFormat enum, which was implemented in the
hope that different flavours of SSE would share the same format;
since they all seem to be different and we now have an sse_version
enum to key off, just use that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-10-peter.maydell@linaro.org
The version of the SYSINFO Register Block in the SSE-300 has
different CIDR/PIDR register values to the SSE-200; pass in
the sse-version property and use it to select the correct
ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-9-peter.maydell@linaro.org
The versions of the Secure Access Configuration Register Block
and Non-secure Access Configuration Register Block in the SSE-300
are the same as those in the SSE-200, but the CIDR/PIDR ID
register values are different.
Plumb through the sse-version property and use it to select
the correct ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-8-peter.maydell@linaro.org
We model Arm "Subsystems for Embedded" SoC subsystems using generic
code which is split into various sub-devices which are configurable
by QOM properties to handle the behaviour differences between the SSE
subsystems we implement. Currently the only sub-device which needs
to change is the IOTKIT_SYSCTL device, and we do this with a mix of
properties that directly specify divergent behaviours (eg
CPUWAIT_RST) and passing it the SYS_VERSION register value as a way
for it to distinguish IoTKit from SSE-200.
The "pass SYS_VERSION" approach is already a bit hacky, since the
IOTKIT_SYSCTL device has to know that the different part of the
register value happens to be bits [31:28]. For SSE-300 this register
is renamed SOC_IDENTITY and has a different format entirely, all of
whose fields can be configured by the SoC integrator when they
integrate the SSE into their SoC, and so "pass SYS_VERSION" breaks
down completely.
Switch to using a simple integer property representing an
internal-to-QEMU enumeration of the SSE flavour. For the moment we
only need this in IOTKIT_SYSCTL, but as we add SSE-300 support a few
of the other devices will also need to know.
We define and permit a value for the SSE-300 so we can start using
it in subsequent commits which add SSE-300 support.
The now-redundant is_sse200 flag in IoTKitSysCtl will be removed
in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-6-peter.maydell@linaro.org
The Clock framework allows users to specify a callback which is
called after the clock's period has been updated. Some users need to
also have a callback which is called before the clock period is
updated.
As the first step in adding support for notifying Clock users on
pre-update events, add an argument to the ClockCallback to specify
what event is being notified, and add an argument to the various
functions for registering a callback to specify which events are
of interest to that callback.
Note that the documentation update renders correct the previously
incorrect claim in 'Adding a new clock' that callbacks "will be
explained in a following section".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-2-peter.maydell@linaro.org
Update old infocenter.arm.com URLs to the equivalent developer.arm.com
ones (the old URLs should redirect, but we might as well avoid the
redirection notice, and the new URLs are pleasantly shorter).
This commit covers the links to the MPS2 board TRM, the various
Application Notes, the IoTKit and SSE-200 documents.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-25-peter.maydell@linaro.org
The AN524 has a PL031 RTC, which we have a model of; provide it
rather than an unimplemented-device stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-23-peter.maydell@linaro.org
The AN524 has a USB controller (an ISP1763); we don't have a model of
it but we should provide a stub "unimplemented-device" for it. This
is slightly complicated because the USB controller shares a PPC port
with the ethernet controller.
Implement a make_* function which provides creates a container
MemoryRegion with both the ethernet controller and an
unimplemented-device stub for the USB controller.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-22-peter.maydell@linaro.org
Add support for the mps3-an524 board; this is an SSE-200 based FPGA
image, like the existing mps2-an521. It has a usefully larger amount
of RAM, and a PL031 RTC, as well as some more minor differences.
In real hardware this image runs on a newer generation of the FPGA
board, the MPS3 rather than the older MPS2. Architecturally the two
boards are similar, so we implement the MPS3 boards in the mps2-tz.c
file as variations of the existing MPS2 boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-21-peter.maydell@linaro.org
The armv7m_load_kernel() function takes a mem_size argument which it
expects to be the size of the memory region at guest address 0. (It
uses this argument only as a limit on how large a raw image file it
can load at address zero).
Instead of hardcoding this value, find the RAMInfo corresponding to
the 0 address and extract its size.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-20-peter.maydell@linaro.org
The AN505 and AN521 don't have any read-only memory, but the AN524
does; add a flag to ROMInfo to mark a region as ROM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-19-peter.maydell@linaro.org
Instead of hardcoding the MachineClass default_ram_size and
default_ram_id fields, set them on class creation by finding the
entry in the RAMInfo array which is marked as being the QEMU system
RAM.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-18-peter.maydell@linaro.org
The AN505 and AN521 have the same layout of RAM; the AN524 does not.
Replace the current hard-coding of where the RAM is and which parts
of it are behind which MPCs with a data-driven approach.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-17-peter.maydell@linaro.org
The AN505 and AN521 have the same device layout, but the AN524 is
somewhat different. Allow for more than one PPCInfo array, which can
be selected based on the board type.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-16-peter.maydell@linaro.org
We create an OR gate to wire together the overflow IRQs for all the
UARTs on the board; this has to have twice the number of inputs as
there are UARTs, since each UART feeds it a TX overflow and an RX
overflow interrupt line. Replace the hardcoded '10' with a
calculation based on the size of the uart[] array in the
MPS2TZMachineState. (We rely on OR gate inputs that are never wired
up or asserted being treated as always-zero.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-15-peter.maydell@linaro.org
Move the specification of the IRQ information for the uart, ethernet,
dma and spi devices to the data structures. (The other devices
handled by the PPCPortInfo structures don't have any interrupt lines
we need to wire up.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-14-peter.maydell@linaro.org
The mps2-tz code uses PPCPortInfo data structures to define what
devices are present and how they are wired up. Currently we use
these to specify device types and addresses, but hard-code the
interrupt line wiring in each make_* helper function. This works for
the two boards we have at the moment, but the AN524 has some devices
with different interrupt assignments.
This commit adds the framework to allow PPCPortInfo structures to
specify interrupt numbers. We add an array of interrupt numbers to
the PPCPortInfo struct, and pass it through to the make_* helpers.
The following commit will change the make_* helpers over to using the
framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-13-peter.maydell@linaro.org
On the MPS2 boards, the first 32 interrupt lines are entirely
internal to the SSE; interrupt lines for devices outside the SSE
start at 32. In the application notes that document each FPGA image,
the interrupt wiring is documented from the point of view of the CPU,
so '0' is the first of the SSE's interrupts and the devices in the
FPGA image itself are '32' and up: so the UART 0 Receive interrupt is
32, the SPI #0 interrupt is 51, and so on.
Within our implementation, because the external interrupts must be
connected to the EXP_IRQ[0...n] lines of the SSE object, we made the
get_sse_irq_in() function take an irqno whose values start at 0 for
the first FPGA device interrupt. In this numbering scheme the UART 0
Receive interrupt is 0, the SPI #0 interrupt is 19, and so on.
The result of these two different numbering schemes has been that
half of the devices were wired up to the wrong IRQs: the UART IRQs
are wired up correctly, but the DMA and SPI devices were passing
start-at-32 values to get_sse_irq_in() and so being mis-connected.
Fix the bug by making get_sse_irq_in() take values specified with the
same scheme that the hardware manuals use, to avoid confusion.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-12-peter.maydell@linaro.org
The AN524 has more interrupt lines than the AN505 and AN521; make
numirq board-specific rather than a compile-time constant.
Since the difference is small (92 on the current boards and 95 on the
new one) we don't dynamically allocate the cpu_irq_splitter[] array
but leave it as a fixed length array whose size is the maximum needed
for any of the boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-10-peter.maydell@linaro.org
In the mps2-tz board code, we handle devices whose interrupt lines
must be wired to all CPUs by creating IRQ splitter devices for the
AN521, because it has 2 CPUs, but wiring the device IRQ directly to
the SSE/IoTKit input for the AN505, which has only 1 CPU.
We can avoid making an explicit check on the board type constant by
instead creating and using the IRQ splitters for any board with more
than 1 CPU. This avoids having to add extra cases to the
conditionals every time we add new boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-9-peter.maydell@linaro.org
Set the FPGAIO num-leds and have-switches properties explicitly
per-board, rather than relying on the defaults. The AN505 and AN521
both have the same settings as the default values, but the AN524 will
be different.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-8-peter.maydell@linaro.org
The AN505 and AN511 happen to share the same OSCCLK values, but the
AN524 will have a different set (and more of them), so split the
settings out to be per-board.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-5-peter.maydell@linaro.org
We were previously using the default OSCCLK settings, which are
correct for the older MPS2 boards (mps2-an385, mps2-an386,
mps2-an500, mps2-an511), but wrong for the mps2-an505 and mps2-511
implemented in mps2-tz.c. Now we're setting the values explicitly we
can fix them to be correct.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-4-peter.maydell@linaro.org
Currently the MPS2 SCC device implements a fixed number of OSCCLK
values (3). The variant of this device in the MPS3 AN524 board has 6
OSCCLK values. Switch to using a PROP_ARRAY, which allows board code
to specify how large the OSCCLK array should be as well as its
values.
With a variable-length property array, the SCC no longer specifies
default values for the OSCCLKs, so we must set them explicitly in the
board code. This defaults are actually incorrect for the an521 and
an505; we will correct this bug in a following patch.
This is a migration compatibility break for all the mps boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-3-peter.maydell@linaro.org
