While FMULX returns a 2.0f float when two operators are infinity and
zero, those operators should be unpacked from raw inputs first. Inconsistent
cases would occur when operators are denormalized floats in flush-to-zero
mode. A wrong codepath will be entered and 2.0f will not be returned
without this patch.
Fix by checking whether inputs need to be flushed before running into
different codepaths.
Signed-off-by: Xiangyu Hu <libhu.so@gmail.com>
Message-id: 1422459650-12490-1-git-send-email-libhu.so@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add assertion checking when cpreg structures are registered that they
either forbid raw-access attempts or at least make an attempt at
handling them. Also add an assert in the raw-accessor-of-last-resort,
to avoid silently doing a read or write from offset zero, which is
actually AArch32 CPU register r0.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1422282372-13735-3-git-send-email-peter.maydell@linaro.org
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
We currently mark ARM coprocessor/system register definitions with
the flag ARM_CP_NO_MIGRATE for two different reasons:
1) register is an alias on to state that's also visible via
some other register, and that other register is the one
responsible for migrating the state
2) register is not actually state at all (for instance the TLB
or cache maintenance operation "registers") and it makes no
sense to attempt to migrate it or otherwise access the raw state
This works fine for identifying which registers should be ignored
when performing migration, but we also use the same functions for
synchronizing system register state between QEMU and the kernel
when using KVM. In this case we don't want to try to sync state
into registers in category 2, but we do want to sync into registers
in category 1, because the kernel might have picked a different
one of the aliases as its choice for which one to expose for
migration. (In particular, on 32 bit hosts the kernel will
expose the state in the AArch32 version of the register, but
TCG's convention is to mark the AArch64 version as the version
to migrate, even if the CPU being emulated happens to be 32 bit,
so almost all system registers will hit this issue now that we've
added AArch64 system emulation.)
Fix this by splitting the NO_MIGRATE flag in two (ALIAS and NO_RAW)
corresponding to the two different reasons we might not want to
migrate a register. When setting up the TCG list of registers to
migrate we honour both flags; when populating the list from KVM,
only ignore registers which are NO_RAW.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1422282372-13735-2-git-send-email-peter.maydell@linaro.org
[PMM: changed ARM_CP_NO_MIGRATE to ARM_CP_ALIAS on new SP_EL1 and
SP_EL2 reginfo stanzas since there was a (semantic) merge conflict
with the patchset that added those]
Update to arm_cpu_reset() to reset into the highest available exception level
based on the set ARM features.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1422029835-4696-4-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added RVBAR_EL2 and RVBAR_EL3 CP register support. All RVBAR_EL# registers
point to the same location and only the highest EL version exists at any one
time.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1422029835-4696-3-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix the RVBAR_EL1 CP register opc2 encoding from 2 to 1
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1422029835-4696-2-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The TARGET_HAS_ICE #define is intended to indicate whether a target-*
guest CPU implementation supports the breakpoint handling. However,
all our guest CPUs have that support (the only two which do not
define TARGET_HAS_ICE are unicore32 and openrisc, and in both those
cases the bp support is present and the lack of the #define is just
a bug). So remove the #define entirely: all new guest CPU support
should include breakpoint handling as part of the basic implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1420484960-32365-1-git-send-email-peter.maydell@linaro.org
The crypto emulation code in target-arm/crypto_helper.c never worked
correctly on big endian hosts, due to the fact that it uses a union
of array types to convert between the native VFP register size (64
bits) and the types used in the algorithms (bytes and 32 bit words)
We cannot just swab between LE and BE when reading and writing the
registers, as the SHA code performs word additions, so instead, add
array accessors for the CRYPTO_STATE type whose LE and BE specific
implementations ensure that the correct array elements are referenced.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 1420208303-24111-1-git-send-email-ard.biesheuvel@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Greg Bellows <greg.bellows@linaro.org>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
on s390 MSI-X irqs are presented as thin or adapter interrupts
for this we have to reorganize the routing entry to contain
valid information for the adapter interrupt code on s390.
To minimize impact on existing code we introduce an architecture
function to fixup the routing entry.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
the sdhci-pci device id to make space for the rocker device.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUp6bMAAoJEL/70l94x66D9q0H/06JFtq/Sn5jLJsWgkU2EcNM
VpV9E2d+RE711PuKkplTj1ee/oYLTnxG9Yf+gdR3KY0hjB/32tHi70ft1WyvbGh/
m/9AiRMmVsKqnZnOlnqgLSN97bV8RNHdpF9wmogdB6xKm5ilICHMnKgRepIBA4HE
J0CeRrFr6LENQbaEU1YGuQ4StithPCSMm3FMNAsvZsM+4ALx+gj7E6NVFgfCyium
oeUyMjqzLE4Ddm3cvelMc0I0hnr7noyzYML6jJaed0XMt5V1Ln/2zUOLfLMc6x9a
SU/mzFnnF2ieqR32M0OijS5E9EHOR46clQlxAQBOdI9qtFTtMYFwe7FIEbvQhJI=
=YI77
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
More migration fixes and more record/replay preparations. Also moves
the sdhci-pci device id to make space for the rocker device.
# gpg: Signature made Sat 03 Jan 2015 08:22:36 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
pci: move REDHAT_SDHCI device ID to make room for Rocker
block/iscsi: fix uninitialized variable
pckbd: set bits 2-3-6-7 of the output port by default
serial: refine serial_thr_ipending_needed
gen-icount: check cflags instead of use_icount global
translate: check cflags instead of use_icount global
cpu-exec: add a new CF_USE_ICOUNT cflag
target-ppc: pass DisasContext to SPR generator functions
atomic: fix position of volatile qualifier
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Added a "has_el3" state property to the ARMCPU descriptor. This property
indicates whether the ARMCPU has security extensions enabled (EL3) or not.
By default it is disabled at this time.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-10-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an unset_feature() function to compliment the set_feature() function. This
will be used to disable functions after they have been enabled during
initialization.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418684992-8996-9-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Merge of the v8_el2_cp_reginfo and el3_cp_reginfo ARMCPRegInfo lists.
Previously, some EL3 registers were restricted to the ARMv8 list under the
impression that they were not needed on ARMv7. However, this is not the case
as the ARMv7/32-bit variants rely on the ARMv8/64-bit variants to handle
migration and reset. For this reason they must always exist.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1418406450-14961-1-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When resetting a VCPU we currently call both kvm_arm_vcpu_init() and
write_kvmstate_to_list(), both of which can fail, but we never check the
return value.
The only choice here is to print an error an exit if the calls fail.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1418039630-11773-1-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For migration to work on 64 bit CPUs, we need to include both
the 64-bit integer register file and the PSTATE. Everything
else is either stored in the same place as existing 32-bit CPU
state or handled by the generic sysreg mechanism.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1417788683-4038-3-git-send-email-peter.maydell@linaro.org
Before we launch a guest we query KVM for the list of "co-processor"
registers it knows about. This is used to synchronize system
register state for the bulk of coprocessor/system registers.
Move this code from the 32-bit specific vcpu init function into
a common routine and call it also from the 64-bit vcpu init.
This allows system registers to migrate correctly when using
KVM, and also permits QEMU code to see the current KVM register
state (which will be needed to support big-endian guests, since
the virtio endianness callback must check for some system register
settings).
Since vcpu reset also has to sync registers, we move the
32 bit kvm_arm_reset_vcpu() into common code as well and
share it with the 64 bit version.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
[PMM: just copy the 32-bit code rather than improving it along the way;
don't share reg_syncs_via_tuple_list() between 32 and 64 bit;
tweak function names; move reset]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added CP register info entries for the ARMv7 MAIR0/1 secure banks.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-26-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
FCSEIDR, CONTEXTIDR, TPIDRURW, TPIDRURO and TPIDRPRW have a secure
and a non-secure instance.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-25-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When EL3 is running in Aarch32 (or ARMv7 with Security Extensions)
VBAR has a secure and a non-secure instance, which are mapped to
VBAR_EL1 and VBAR_EL3.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-24-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
PAR has a secure and a non-secure instance.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-23-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
IFAR and DFAR have a secure and a non-secure instance.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-22-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
DFSR has a secure and a non-secure instance.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-21-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
IFSR has a secure and a non-secure instance. Adds IFSR32_EL2 definition and
storage.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-20-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When EL3 is running in AArch32 (or ARMv7 with Security Extensions)
DACR has a secure and a non-secure instance. Adds definition for DACR32_EL2.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-19-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds secure and non-secure bank register suport for TTBCR.
Added new struct to compartmentalize the TCR data and masks. Removed old
tcr/ttbcr data and added a 4 element array of the new structs in cp15. This
allows for one entry per EL. Added a CP register definition for TCR_EL3.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-18-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds secure and non-secure bank register suport for TTBR0 and TTBR1.
Changes include adding secure and non-secure instances of ttbr0 and ttbr1 as
well as a CP register definition for TTBR0_EL3. Added a union containing
both EL based array fields and secure and non-secure fields mapped to them.
Updated accesses to use A32_BANKED_CURRENT_REG_GET macro.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-17-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add checks of SCR AW/FW bits when performing writes of CPSR. These SCR bits
are used to control whether the CPSR masking bits can be adjusted from
non-secure state.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-15-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use MVBAR register as exception vector base address for
exceptions taken to CPU monitor mode.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-13-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added CP register defintions for SDER and SDER32_EL3 as well as cp15.sder for
register storage.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-12-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Define a new ARM CP register info list for the ARMv7 Security Extension
feature. Register that list only for ARM cores with Security Extension/EL3
support. Moving AArch32 SCR into Security Extension register group.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-9-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Prepare for cp register banking by inserting every cp register twice,
once for secure world and once for non-secure world.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-8-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Added additional NS-bit to CPREG hash encoding. Updated hash lookup
locations to specify hash bit currently set to non-secure.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-7-git-send-email-greg.bellows@linaro.org
[PMM: fix uses of ENCODE_CP_REG in kvm32.c to add extra argument]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Prepare ARMCPRegInfo to support specifying two fieldoffsets per
register definition. This will allow us to keep one register
definition for banked registers (different offsets for secure/
non-secure world).
Also added secure state tracking field and flags. This allows for
identification of the register info secure state.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-6-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch is based on idea found in patch at
git://github.com/jowinter/qemu-trustzone.git
f3d955c6c0ed8c46bc0eb10b634201032a651dd2 by
Johannes Winter <johannes.winter@iaik.tugraz.at>.
The TBFLAG captures the SCR NS secure state at the time when a TB is created so
the correct bank is accessed on system register accesses.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-5-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If EL3 is in AArch32 state certain cp registers are banked (secure and
non-secure instance). When reading or writing to coprocessor registers
the following macros can be used.
- A32_BANKED macros are used for choosing the banked register based on provided
input security argument. This macro is used to choose the bank during
translation of MRC/MCR instructions that are dependent on something other
than the current secure state.
- A32_BANKED_CURRENT macros are used for choosing the banked register based on
current secure state. This is NOT to be used for choosing the bank used
during translation as it breaks monitor mode.
If EL3 is operating in AArch64 state coprocessor registers are not
banked anymore. The macros use the non-secure instance (_ns) in this
case, which is architecturally mapped to the AArch64 EL register.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-4-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds a dedicated function and a lookup table for determining the target
exception level of IRQ and FIQ exceptions. The lookup table is taken from the
ARMv7 and ARMv8 specification exception routing tables.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-3-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch extends arm_excp_unmasked() to use lookup tables for determining
whether IRQ and FIQ exceptions are masked. The lookup tables are based on the
ARMv8 and ARMv7 specification physical interrupt masking tables.
If EL3 is using AArch64 IRQ/FIQ masking is ignored in all exception levels
other than EL3 if SCR.{FIQ|IRQ} is set to 1 (routed to EL3).
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1416242878-876-2-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to run unit tests under semihosting, it is necessary to pass the
application exit code back to the system.
ARM defines only the code to be used for non-error application exit
(ADP_Stopped_ApplicationExit), all other codes should return non-zero
exit codes.
This patch checks if the application code passed via TARGET_SYS_EXIT is
ADP_Stopped_ApplicationExit, and return 0, otherwise return 1.
Signed-off-by: Liviu Ionescu <ilg@livius.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARMv8 address translation system defines that a page table walk
starts at a level which depends on the translation granule size
and the number of bits of virtual address that need to be resolved.
Where the translation granule is 64KB and the guest sets the
TCR.TxSZ field to between 35 and 39, it's actually possible to
start at level 3 (the final level). QEMU's implementation failed
to handle this case, and so we would set level to 2 and behave
incorrectly (including invoking the C undefined behaviour of
shifting left by a negative number). Correct the code that
determines the starting level to deal with the start-at-3 case,
by replacing the if-else ladder with an expression derived from
the ARM ARM pseudocode version.
This error was detected by the Coverity scan, which spotted
the potential shift by a negative number.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1415890569-7454-1-git-send-email-peter.maydell@linaro.org
The VIRQ and VFIQ exceptions are (as the comments say) only
taken if the CPU is in Non-secure state and the IMO/FMO bits
are set to enable virtualized interrupts. Correct the code
to actually implement this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1414684132-23971-3-git-send-email-peter.maydell@linaro.org
The M profile cpu_exec_interrupt handling is fairly simple
but does include an M profile specific oddity (disabling
interrupts for certain PC values). A/R profile handling
on the other hand is getting rapidly more complicated
with the support for EL2 and EL3. Split the M profile
code out into its own implementation of cpu_exec_interrupt
to keep these two things out of each others' way.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1414684132-23971-2-git-send-email-peter.maydell@linaro.org
Refactor to avoid passing a CPUARMState * to disas_arm_insn(). To do this
we move the "read insn from memory" code to the callsite and pass the
insn to the function instead.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1414524244-20316-6-git-send-email-peter.maydell@linaro.org
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Passing the CPUARMState around in the decoder is a recipe for
bugs where we accidentally generate code that depends on CPU
state which isn't reflected in the TB flags. Stop doing this
and instead use DisasContext as a way to pass around those
bits of CPU state which are known to be safe to use.
This commit simply removes initial "CPUARMState *env" parameters
from various function definitions, and removes the initial "env"
argument from the places where those functions are called.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1414524244-20316-5-git-send-email-peter.maydell@linaro.org
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Instead of using IS_M(), use arm_dc_feature(s, ARM_FEATURE_M), so we
don't need to pass CPUARMState pointers around the decoder.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1414524244-20316-4-git-send-email-peter.maydell@linaro.org
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
Use arm_dc_feature() rather than arm_feature() to avoid using
CPUARMState unnecessarily.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1414524244-20316-3-git-send-email-peter.maydell@linaro.org
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
All the places where we use the ENABLE_ARCH_* and ARCH() macros have a
DisasContext* s, so switch them over to use arm_dc_feature() rather than
arm_feature() so we don't need to pass the CPUARMState* env around too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1414524244-20316-2-git-send-email-peter.maydell@linaro.org
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
There is not much point storing the same value twice in a row.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Implements SMC instruction in AArch32 using the A32 syndrome. When executing
SMC instruction from monitor CPU mode SCR.NS bit is reset.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Message-id: 1413910544-20150-7-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make arm_current_el() return EL3 for secure PL1 and monitor mode.
Increase MMU modes since mmu_index is directly inferred from arm_
current_el(). Change assertion in arm_el_is_aa64() to allow EL3.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1413910544-20150-6-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Renamed the arm_current_pl CPU function to more accurately represent that it
returns the ARMv8 EL rather than ARMv7 PL.
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1413910544-20150-5-git-send-email-greg.bellows@linaro.org
[PMM: fixed a minor merge resolution error in a couple of hunks]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
arm_is_secure() function allows to determine CPU security state
if the CPU implements Security Extensions/EL3.
arm_is_secure_below_el3() returns true if CPU is in secure state
below EL3.
Signed-off-by: Sergey Fedorov <s.fedorov@samsung.com>
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1413910544-20150-3-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Increasing banked_r13 and banked_r14 to store LR_mon and SP_mon (bank
index 7).
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1413910544-20150-2-git-send-email-greg.bellows@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM ARM requires that the FPINST and FPINST2 VFP control
registers are not accessible to code at EL0. We were already
correctly implementing this for reads of these registers; add
the missing check for the write code path.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 1412967447-20931-1-git-send-email-peter.maydell@linaro.org
For the CPU type "any" (only used with linux-user) we were reporting
the L1Ip field as 0b00, which is reserved. Change this field to 0b10
instead, indicating a VIPT icache as the comment describes.
Reported-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 1412966807-20844-1-git-send-email-peter.maydell@linaro.org
The DZP bit in the DCZID system register should be set if
the control bits which prohibit use of the DC ZVA instruction
have been set (it stands for Data Zero Prohibited). However
we had the sense of the test inverted; fix this so that the
bit reads correctly.
To avoid this regressing the behaviour of the user-mode
emulator, we must set the DZE bit in the SCTLR for that
config so that userspace continues to see DZP as zero (it
was getting the correct result by accident previously).
Reported-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christopher Covington <cov@codeaurora.org>
Message-id: 1412959792-20708-1-git-send-email-peter.maydell@linaro.org
Add support for handling PSCI calls in system emulation. Both version
0.1 and 0.2 of the PSCI spec are supported. Platforms can enable support
by setting the "psci-conduit" QOM property on the cpus to SMC or HVC
emulation and having a PSCI binding in their dtb.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1412865028-17725-7-git-send-email-peter.maydell@linaro.org
[PMM: made system reset/off PSCI functions power down the CPU so
we obey the PSCI API requirement never to return from them;
rearranged how the code is plumbed into the exception system,
so that we split "is this a valid call?" from "do the call"]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for HVC and SMC instructions to the A32 and
T32 decoder. Using these for real exceptions to EL2 or EL3
is currently not supported (the do_interrupt routine does
not handle them) but we require the instruction support to
implement PSCI.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1412865028-17725-6-git-send-email-peter.maydell@linaro.org
SMC must UNDEF if EL3 is not implemented; similarly HVC UNDEFs
if EL2 is not implemented. Move the handling of this from
translate-a64.c into the pre_smc and pre_hvc helper functions.
This is necessary because use of these instructions for PSCI
takes precedence over this UNDEF case, and we can't tell if
this is a PSCI call until runtime.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1412865028-17725-5-git-send-email-peter.maydell@linaro.org
This adds some PSCI function IDs and symbolic return codes that are needed
to implement PSCI emulation in TCG mode.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1412865028-17725-4-git-send-email-peter.maydell@linaro.org
User mode emulation should never get interrupts and thus should not
use the system emulation exception handler function. Remove the reference,
and '#ifndef USER_MODE_ONLY' the function itself as well, so that we can add
system mode only functionality to it.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1412865028-17725-3-git-send-email-peter.maydell@linaro.org
Add tracking of cpu power state in order to support powering off of
cores in system emuluation. The initial state is determined by the
start-powered-off QOM property.
Signed-off-by: Rob Herring <rob.herring@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1412865028-17725-2-git-send-email-peter.maydell@linaro.org
GDB assumes that watchpoint set via the gdbstub remote protocol will
behave in the same way as hardware watchpoints for the target. In
particular, whether the CPU stops with the PC before or after the insn
which triggers the watchpoint is target dependent. Allow guest CPU
code to specify which behaviour to use. This fixes a bug where with
guest CPUs which stop before the accessing insn GDB would manually
step forward over what it thought was the insn and end up one insn
further forward than it should be.
We set this flag for the CPU architectures which set
gdbarch_have_nonsteppable_watchpoint in gdb 7.7:
ARM, CRIS, LM32, MIPS and Xtensa.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Michael Walle <michael@walle.cc> (for lm32)
Message-id: 1410545057-14014-1-git-send-email-peter.maydell@linaro.org
This only implements the external delivery method via the GIC.
Acked-by: Greg Bellows <greg.bellows@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1411718914-6608-12-git-send-email-edgar.iglesias@gmail.com
[PMM: adjusted following cpu-exec refactoring]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1411718914-6608-11-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Not all exception types update both FAR and ESR.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1411718914-6608-7-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1411718914-6608-6-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1411718914-6608-5-git-send-email-edgar.iglesias@gmail.com
[PMM: updated to account for recent cpu-exec refactoring]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce new_el and new_mode in preparation for future patches
that add support for taking exceptions to and from EL2 and 3.
No functional change.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1411718914-6608-4-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1411718914-6608-3-git-send-email-edgar.iglesias@gmail.com
[PMM: apply offsetoflow32() to correct regdef]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1411718914-6608-2-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At the moment we try to handle c15_cpar with the strategy of:
* emit generated code which makes assumptions about its value
* when the register value changes call tb_flush() to throw
away the now-invalid generated code
This works because XScale CPUs are always uniprocessor, but
it's confusing because it suggests that the same approach can
be taken for other registers. It also means we do a tb_flush()
on CPU reset, which makes multithreaded linux-user binaries
even more likely to fail than would otherwise be the case.
Replace it with a combination of TB flags for the access
checks done on cp0/cp1 for the XScale and iwMMXt instructions,
plus a runtime check for cp2..cp13 coprocessor accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1411056959-23070-1-git-send-email-peter.maydell@linaro.org
Implement handling of breakpoint event firing to correctly
inject the debug exception into the guest.
Since the breakpoint and watchpoint control register format is
very similar we adjust wp_matches() to also handle breakpoints
as well rather than using a separate function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1410523465-13400-3-git-send-email-peter.maydell@linaro.org
This patch adds support for setting guest breakpoints
based on values the guest writes to the DBGBVR and DBGBCR
registers. (It doesn't include the code to handle when
these breakpoints fire, so has no guest-visible effect.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1410523465-13400-2-git-send-email-peter.maydell@linaro.org
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-id: 1410626734-3804-15-git-send-email-rth@twiddle.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM architecture defines that the "IS" variants of TLB
maintenance operations must affect all TLBs in the Inner Shareable
domain, which for us means all CPUs. We were incorrectly implementing
these to only affect the current CPU, which meant that SMP TCG
operation was unstable.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1410274883-9578-3-git-send-email-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org
When we implemented ARMv8 in QEMU we retained our legacy loose
wildcarded decoding of the TLB maintenance operations for v7
and earlier CPUs and provided the correct stricter decode for
v8. However the loose decode is in fact wrong for v7MP, because
it doesn't correctly implement the operations which must apply
to every CPU in the Inner Shareable domain.
Move the legacy wildcarding from the not_v8 reginfo array
into the not_v7 array, and move the strictly decoded operations
from the v8 reginfo to v7 or v7mp arrays as appropriate.
Cache and TLB lockdown legacy wildcarding remains in the
not_v8 array for the moment.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1410274883-9578-2-git-send-email-peter.maydell@linaro.org
Cc: qemu-stable@nongnu.org
Implement debug registers DBGVCR, OSDLR_EL1 and MDCCSR_EL0
(as dummy or limited-functionality). 32 bit Linux kernels will
access these at startup so they are required for breakpoints
and watchpoints to be supported.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
MDSCR_EL1 has actual functionality now; remove the out of date
comment that claims it is a dummy implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For debug exceptions taken to AArch32 we have to set the
DBGDSCR.MOE (Method Of Entry) bits; we can identify the
kind of debug exception from the information in
exception.syndrome.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the utility function extended_addresses_enabled() into
internals.h; we're going to need to call it from op_helper.c.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement support for setting QEMU watchpoints based on the
values the guest writes to the ARM architected watchpoint
registers. (We do not yet report the firing of the watchpoints
to the guest, so they will just be ignored.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix a single misindented line in arm_cpu_reset().
Signed-off-by: Martin Galvan <martin.galvan@tallertechnologies.com>
[PMM: split this out from the previous commit]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When calling qemu_system_reset after startup on a Cortex-M
CPU, the initial values of PC, MSP and the Thumb bit weren't being set
correctly if the vector table was in ROM. In particular, since Thumb was 0, a
Usage Fault would arise immediately after trying to execute any instruction
on a Cortex-M.
Signed-off-by: Martin Galvan <martin.galvan@tallertechnologies.com>
Message-id: CAOKbPbaLt-LJsAKkQdOE0cs9Xx4OWrUfpDhATXPSdtuNw2xu_A@mail.gmail.com
[PMM: removed an incorrect comment]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the function that is called when writing to the
PMCCFILTR_EL0 register
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 73da3da6404855b17d5ae82975a32ff3a4dcae3d.1409025949.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the old PMCCNTR code and replace it with calls to the new
pmccntr_sync() and arm_ccnt_enabled() functions.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 693a6e437d915c2195fd3dc7303f384ca538b7bf.1409025949.git.peter.crosthwaite@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Xiangyu Hu
Peter Maydell
Greg Bellows
Paolo Bonzini
Ard Biesheuvel
Stefan Weil
Frank Blaschka
Fabian Aggeler
Christoffer Dall
Alex Bennée
Sergey Fedorov
Liviu Ionescu
Rob Herring
Edgar E. Iglesias
Richard Henderson
Martin Galvan
Alistair Francis