This interface will be used by HMP commands 'info irq' and 'info pic'.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-Id: <1474921408-24710-2-git-send-email-hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's 2.8 now, and maybe it's time to switch IOAPIC default version to
0x20.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1474608795-23058-1-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fix inconsistent irq status, because of this in the trace logs, for e.g.
LSI status was 0x7, i.e. XICS_STATUS_ASSERTED, XICS_STATUS_SENT and
XICS_STATUS_REJECTED all set, which did not make sense. So the REJECTED
would have been set in earlier interrupt cycle, and then asserted and
sent in this current one.
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Introduce a new APIC macro to replace APIC_COMMON macro in
hw/intc/apic.c in order to capture access LAPIC in qemu
even if LAPIC is emulated in kvm.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Message-Id: <1473923759-13912-1-git-send-email-wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We abort a few lines above if kernel_xics_fd == -1.
This is only code cleanup.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some old Linux kernels (upstream before v4.0), or any released RHEL
kernels has problem in sending APIC EOI when IR is enabled. Meanwhile,
many of them only support explicit EOI for IOAPIC, which is only
introduced in IOAPIC version 0x20. This patch provide a way to boost
QEMU IOAPIC to version 0x20, in order for QEMU to correctly receive EOI
messages.
Without boosting IOAPIC version to 0x20, kernels before commit d32932d
("x86/irq: Convert IOAPIC to use hierarchical irqdomain interfaces")
will have trouble enabling both IR and level-triggered interrupt devices
(like e1000).
To upgrade IOAPIC to version 0x20, we need to specify:
-global ioapic.version=0x20
To be compatible with old systems, 0x11 will still be the default IOAPIC
version. Here 0x11 and 0x20 are the only versions to be supported.
One thing to mention: this patch only applies to emulated IOAPIC. It
does not affect kernel IOAPIC behavior.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1470059959-372-1-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For level triggered interrupts, we will get Remote IRR bit cleared after
guest kernel finished processing specific request. Before that, we
should ignore the same interrupt from triggering again.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1469974685-4144-1-git-send-email-peterx@redhat.com>
[Push new "if" up so that it covers KVM split irqchip as well. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXkQsqAAoJECgfDbjSjVRpanoIAJ9JVlc1aEjt9sa0cSBcs+NQ
J7JmgU9FqFsj+4FrNTouO3AxTjHurd1UAULP1WMPD+V3JpbnHct8r6SCBLQ5EBMN
VOjYo4DwWs1g+DqnQ9WZmbadu06XvYi/yiAKNUzWfZk0MR11D0D/S5hmarNKw0Kq
tGHeTWjGeY4WqFLV7m+qB4+cqkAByn6um99UtUvgLL05RgIEIP2IEMKYZ+rXvAa9
iGUvzqlO7mbq/+LbL18kaWywa4TCwbbd2eSGWaqhX4CuB62Rl33mWTXFcfaYhkyp
Z3FgwaJ09h0lAjSVEbyAuLFMfO/BnMcsoKqwl4xc4vkn/xBCqFtgH9JcEVm3O8U=
=ge2D
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio: new features, cleanups, fixes
- interrupt remapping for intel iommus
- a bunch of virtio cleanups
- fixes all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 21 Jul 2016 18:49:30 BST
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (57 commits)
intel_iommu: avoid unnamed fields
virtio: Update migration docs
virtio-gpu: Wrap in vmstate
virtio-gpu: Use migrate_add_blocker for virgl migration blocking
virtio-input: Wrap in vmstate
9pfs: Wrap in vmstate
virtio-serial: Wrap in vmstate
virtio-net: Wrap in vmstate
virtio-balloon: Wrap in vmstate
virtio-rng: Wrap in vmstate
virtio-blk: Wrap in vmstate
virtio-scsi: Wrap in vmstate
virtio: Migration helper function and macro
virtio-serial: Remove old migration version support
virtio-net: Remove old migration version support
virtio-scsi: Replace HandleOutput typedef
Revert "mirror: Workaround for unexpected iohandler events during completion"
virtio-scsi: Call virtio_add_queue_aio
virtio-blk: Call virtio_add_queue_aio
virtio: Introduce virtio_add_queue_aio
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let IOAPIC the first consumer of x86 IOMMU IEC invalidation
notifiers. This is only used for split irqchip case, when vIOMMU
receives IR invalidation requests, IOAPIC will be notified to update
kernel irq routes. For simplicity, we just update all IOAPIC routes,
even if the invalidated entries are not IOAPIC ones.
Since now we are creating IOMMUs using "-device" parameter, IOMMU
device will be created after IOAPIC. We need to do the registration
after machine done by leveraging machine_done notifier.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Abstract IOAPIC entry parsing logic into a helper function.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch translates all IOAPIC interrupts into MSI ones. One pseudo
ioapic address space is added to transfer the MSI message. By default,
it will be system memory address space. When IR is enabled, it will be
IOMMU address space.
Currently, only emulated IOAPIC is supported.
Idea suggested by Jan Kiszka and Rita Sinha in the following patch:
https://lists.gnu.org/archive/html/qemu-devel/2016-03/msg01933.html
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
instance_id is generated by last_used_id + 1 for a given device type
so for QEMU with 3 CPUs instance_id for APICs is a seti of [0, 1, 2]
When CPU in the middle is hot-removed and migration started
APICs with instance_ids 0 and 2 are transferred in migration stream.
However target starts with 2 CPUs and APICs' instance_ids are
generated from scratch [0, 1] hence migration fails with error
Unknown savevm section or instance 'apic' 2
Fix issue by manually registering APIC's vmsd with apic_id as
instance_id, in this case instance_id on target will always
match instance_id on source as apic_id is the same for a given
cpu instance.
Reported-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Callbacks will do necessary cleanups before APIC device is deleted
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
local_apics[] is sized to contain all APIC ID supported in xAPIC mode,
so use APIC ID as index in it instead of constantly increasing counter idx.
Fixes error "apic initialization failed" when a CPU hotplugged and
unplugged more times than there are free slots in local_apics[].
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
MAX_APICS is only used by child 'apic' class and not
by its parent TYPE_APIC_COMMON or any other derived
class.
Move check into end user 'apic' class so it won't
get in the way of other APIC implementations
if they support more then MAX_APICS.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Coverity complains that the GICR_IPRIORITYR case in gicv3_readl()
can overflow an array, because it doesn't know that the offsets
passed to that function must be word aligned. Add some assert()s
which hopefully tell Coverity that this isn't possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1468261372-17508-1-git-send-email-peter.maydell@linaro.org
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJXhMtOAAoJEFIRjjwLKdprahQH/2qBMp7Hnucy7jhiPHRtRZTo
zZAhuRJ0Z2LT9xH+sTg3HcjHI7aXps5cG2f7Fw4X/JKNRY4KO19yEBnMhc5he2Ut
XPtHCeMXXq6zU4RMHqlx6wChHn5AUll/3EeSvm6JMV+HhE6oDBk1yl5C8ipPlVCd
KEz6LlUFNMbuxu2tM4DoMNAWeKmunBx3vO+JuErB6hjCWM5G0mV9aPDkbwTOmVLn
qGgzzmNDiPE6JWrSpbHetsdCO7V9xtXzhcFsu240GJ/+XJMjUXb1m6ETsJxT9EYh
vLfFzwozBSjX6ZQZVNFIAeJZnq96NOHqZ56sU7s4YktVXjl26JAahScTTH0aiNo=
=sTce
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lalrae/tags/mips-20160712' into staging
MIPS patches 2016-07-12
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
# gpg: Signature made Tue 12 Jul 2016 11:49:50 BST
# gpg: using RSA key 0x52118E3C0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
# Primary key fingerprint: 8DD3 2F98 5495 9D66 35D4 4FC0 5211 8E3C 0B29 DA6B
* remotes/lalrae/tags/mips-20160712:
target-mips: enable 10-bit ASIDs in I6400 CPU
target-mips: support CP0.Config4.AE bit
target-mips: change ASID type to hold more than 8 bits
target-mips: add ASID mask field and replace magic values
target-mips: replace MIPS64R6-generic with the real I6400 CPU model
hw/mips_cmgcr: implement RESET_BASE register in CM GCR
hw/mips_cpc: make VP correctly start from the reset vector
target-mips: add exception base to MIPS CPU
hw/mips/cps: create GIC block inside CPS
hw/mips: implement Global Interrupt Controller
hw/mips: implement GIC Interval Timer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Global Interrupt Controller (GIC) is responsible for mapping each
internal and external interrupt to the correct location for servicing.
The internal representation of registers is different from the specification
in order to consolidate information for each GIC Interrupt Sources and Virtual
Processors with same functionalities. For example SH_MAP00_VP00 registers are
defined like each bit represents a VP but in this implementation the equivalent
map_vp contains VP number in integer form for ease accesses. When it is being
accessed via read write functions an internal data is converted back into the
original format as the specification.
Limitations:
Level triggering only
GIC CounterHi not implemented (Countbits = 32bits)
DINT not implemented
Local WatchDog, Fast Debug Channel, Perf Counter not implemented
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Starting QEMU with -S results in current_cpu containing its initial
value of NULL. It is however possible to connect to such QEMU instance
and query various CPU registers, one example being CPUID, and doing that
results in QEMU segfaulting.
Using qemu_get_cpu(0) seem reasonable enough given that ARMv7M
architecture is a single core architecture.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "ICP" is a different object than the "XICS". For historical reasons,
we have a number of places where we name a variable "icp" while it contains
a XICSState pointer. There *is* an ICPState structure too so this makes
the code really confusing.
This is a mechanical replacement of all those instances to use the name
"xics" instead. There should be no functional change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[spapr_cpu_init has been moved to spapr_cpu_core.c, change there]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
None of the other presenter functions directly mucks with the
internal state, so don't do it there either.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Leave the core ICP/ICS logic in xics.c and move the top level
class wrapper, hypercall and RTAS handlers to xics_spapr.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[add cpu.h in xics_spapr.c, move set_nr_irqs and set_nr_servers to
xics_spapr.c]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The common class doesn't change, the KVM one is sPAPR specific. Rename
variables and functions to xics_spapr.
Retain the type name as "xics" to preserve migration for existing sPAPR
guests.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
These are spotted by coverity 1356936 and 1356937.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1466387717-13740-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
[dwg: Adjusted for context to apply without original series]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Version: GnuPG v1
iQEcBAABAgAGBQJXaFInAAoJEJykq7OBq3PI6VsH/0Sfgbdo1RksYuQwb/y92sCW
EN+lxUZ+OLfgrc8PYgNZwfSM3rsfYhznL0MAXOeEe7Ahabi07w7DhGR8WvwfAOlI
G96FRuvrIPfv5u6U6fwS4CvG3TIHVLxfHKCsTpPUmH8U5CNx/x/tpjNiWN1dj6t+
sXybSjYHfZfiZy2tI9MFIFWCdxnF/pl0QAPhbRqc8Y/RQTDrPKRjLpz+nitN/u96
5TS7KlELyQuP91YMmLceYSmIkHbxW703h+iE2n4hov0uZCP8Jil+2Jsd3ziQSRlL
j6LqexQ2ViBGdDSfiZGYES2VPlsHOCwb4G+IgWBStfZg1ppaXENvcDzPrgrB+L4=
=eUnF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha/tags/tracing-pull-request' into staging
# gpg: Signature made Mon 20 Jun 2016 21:29:27 BST
# gpg: using RSA key 0x9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha/tags/tracing-pull-request: (42 commits)
trace: split out trace events for linux-user/ directory
trace: split out trace events for qom/ directory
trace: split out trace events for target-ppc/ directory
trace: split out trace events for target-s390x/ directory
trace: split out trace events for target-sparc/ directory
trace: split out trace events for net/ directory
trace: split out trace events for audio/ directory
trace: split out trace events for ui/ directory
trace: split out trace events for hw/alpha/ directory
trace: split out trace events for hw/arm/ directory
trace: split out trace events for hw/acpi/ directory
trace: split out trace events for hw/vfio/ directory
trace: split out trace events for hw/s390x/ directory
trace: split out trace events for hw/pci/ directory
trace: split out trace events for hw/ppc/ directory
trace: split out trace events for hw/9pfs/ directory
trace: split out trace events for hw/i386/ directory
trace: split out trace events for hw/isa/ directory
trace: split out trace events for hw/sd/ directory
trace: split out trace events for hw/sparc/ directory
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move all trace-events for files in the hw/intc/ directory to
their own file.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 1466066426-16657-10-git-send-email-berrange@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Acked-by: Michael Walle <michael@walle.cc>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michael Walle <michael@walle.cc>
Use Coccinelle script to replace 'ret = E; return ret' with
'return E'. The script will do the substitution only when the
function return type and variable type are the same.
Manual fixups:
* audio/audio.c: coding style of "read (...)" and "write (...)"
* block/qcow2-cluster.c: wrap line to make it shorter
* block/qcow2-refcount.c: change indentation of wrapped line
* target-tricore/op_helper.c: fix coding style of
"remainder|quotient"
* target-mips/dsp_helper.c: reverted changes because I don't
want to argue about checkpatch.pl
* ui/qemu-pixman.c: fix line indentation
* block/rbd.c: restore blank line between declarations and
statements
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1465855078-19435-4-git-send-email-ehabkost@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Unused Coccinelle rule name dropped along with a redundant comment;
whitespace touched up in block/qcow2-cluster.c; stale commit message
paragraph deleted]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Fix missing includes of qemu/log.h, which broke compilation with the
simple trace backend (the default backend pulls in log.h implicitly
via trace.h).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Tested-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Message-id: 1466416634-9798-1-git-send-email-peter.maydell@linaro.org
Add the CPU interface registers which deal with acknowledging
and dismissing interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-19-git-send-email-peter.maydell@linaro.org
Implement the registers in the GICv3 CPU interface which generate
new SGI interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-18-git-send-email-peter.maydell@linaro.org
Implement the gicv3_cpuif_update() function which deals with correctly
asserting IRQ and FIQ based on the current running priority of the CPU,
the priority of the highest priority pending interrupt and the CPU's
current exception level and security state.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-17-git-send-email-peter.maydell@linaro.org
Implement the CPU interface registers for the GICv3; these are
CPU system registers, not MMIO registers.
This commit implements all the registers which are simple
accessors for GIC state, but not those which act as interfaces
for acknowledging, dismissing or generating interrupts. (Those
will be added in a later commit.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-16-git-send-email-peter.maydell@linaro.org
Implement the code which updates the GIC state when an interrupt
input into the GIC is asserted.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-15-git-send-email-peter.maydell@linaro.org
Wire up the MMIO functions exposed by the distributor and the
redistributor into MMIO regions exposed by the GICv3 device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-14-git-send-email-peter.maydell@linaro.org
Implement the redistributor registers of a GICv3.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-13-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled/rewritten:
* use the new data structures
* restructure register read/write to handle different width accesses
natively, since almost all registers are 32-bit only, rather
than implementing everything as byte accesses
* implemented security extension support
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the distributor registers of a GICv3.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-12-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled/rewritten:
* use the new bitmap data structures
* restructure register read/write to handle different width accesses
natively, since almost all registers are 32-bit only, rather
than implementing everything as byte accesses
* implemented security extension support
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the GICv3 logic to recalculate the highest priority pending
interrupt for each CPU after some part of the GIC state has changed.
We avoid unnecessary full recalculation where possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-11-git-send-email-peter.maydell@linaro.org
This patch includes the device class itself, some ID register
value functions which will be needed by both distributor
and redistributor, and some skeleton functions for handling
interrupts coming in and going out, which will be filled in
in a subsequent patch.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-10-git-send-email-peter.maydell@linaro.org
[PMM: pulled this patch earlier in the sequence, and left
some code out of it for a later patch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Add state structure descriptors for the GICv3 state. We mark
the KVM GICv3 device as having a migration blocker until the
code to save and restore the state in the kernel is implemented.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-9-git-send-email-peter.maydell@linaro.org
[PMM: Adjust to renamed struct fields; switched to using uint32_t
array backed bitmaps; add migration blocker setting]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the GICv3 parent_irq and parent_fiq pointers into the
GICv3CPUState structure rather than giving them their own array.
This will make it easy to assert the IRQ and FIQ lines for a
particular CPU interface without having to know or calculate
the CPU index for the GICv3CPUState we are working on.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1465915112-29272-8-git-send-email-peter.maydell@linaro.org
Add state information to GICv3 object structure and implement
arm_gicv3_common_reset().
This commit includes accessor functions for the fields which are
stored as bitmaps in uint32_t arrays.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1465915112-29272-7-git-send-email-peter.maydell@linaro.org
[PMM: significantly overhauled:
* Add missing qom/cpu.h include
* Remove legacy-only state fields (we can add them later if/when we add
legacy emulation)
* Use arrays of uint32_t to store the various distributor bitmaps,
and provide accessor functions for the various set/test/etc operations
* Add various missing register offset #defines
* Accessor macros which combine distributor and redistributor behaviour
removed
* Fields in state structures renamed to match architectural register names
* Corrected the reset value for GICR_IENABLER0 since we don't support
legacy mode
* Added ARM_LINUX_BOOT_IF interface for "we are directly booting a kernel in
non-secure" so that we can fake up the firmware-mandated reconfiguration
only when we need it
]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
XICS is setup for each CPU during initialization. Provide a routine
to undo the same when CPU is unplugged. While here, move ss->cs management
into xics from xics_kvm since there is nothing KVM specific in it.
Also ensure xics reset doesn't set irq for CPUs that are already unplugged.
This allows reboot of a VM that has undergone CPU hotplug and unplug
to work correctly.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
According to the platform specification, under certain conditions,
pending IO interruptions have to be cleared. Let's add an interface
for that.
Signed-off-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Treat non-secure accesses to registers and bits in registers of secure
interrupts as RAZ/WI.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Message-id: 1464273945-2055-1-git-send-email-jens.wiklander@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is to better emulate IOAPIC version 0x1X hardware. Linux kernel
leveraged this "feature" to do explicit EOI since EOI register is still
not introduced at that time. This will also fix the issue that level
triggered interrupts failed to work when IR enabled (tested with Linux
kernel version 4.5).
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1462875682-1349-3-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently IOAPIC RO bits can be written. To be better aligned with
hardware, we should let them read-only.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <1462875682-1349-2-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is not visible with the default "log" trace backend. With other
backends however trace.h does not include qemu/log.h, resulting in
build failures.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1463745452-25831-2-git-send-email-pbonzini@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Memory barriers are needed also by Xen and, when the ioeventfd
bugs are fixed, by TCG as well.
sysemu/kvm.h is not anymore needed in sysemu/dma.h, move it to
the actual users.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These are obviously critical to understanding interrupt delivery:
gic_enable_irq
gic_disable_irq
gic_set_irq (inbound irq from device models)
gic_update_set_irq (outbound irq to CPU)
gic_acknowledge_irq
The only one that I think might raise eyebrows is gic_update_bestirq, but I've
(sadly) debugged problems that ended up being caused by unexpected priorities.
Knowing that the GIC has an irq ready, but doesn't deliver to the CPU due to
priority, has also proven important.
Signed-off-by: Hollis Blanchard <hollis_blanchard@mentor.com>
Message-id: 1461252281-22399-1-git-send-email-hollis_blanchard@mentor.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
* Split the old SysBus init into an instance_init and a
DeviceClass::realize function
* Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Split the old SysBus init into an instance_init and a
DeviceClass::realize function
* Drop the old SysBus init function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: corrected "can not" to "cannot" in error message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Drop the old SysBus init function and use instance_init
* Split the exynos4210_irq_gate_init into an instance_init
and a DeviceClass::realize function
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Drop the old SysBus init function and use instance_init
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch replaces get_ticks_per_sec() calls with the macro
NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec()
is then removed. This replacement improves the readability and
understandability of code.
For example,
timer_mod(fdctrl->result_timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50));
NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns
matches the unit of the expression on the right side of the plus.
Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Implement a basic ASPEED VIC device model for the AST2400 SoC[1], with
enough functionality to boot an aspeed_defconfig Linux kernel. The model
implements the 'new' (revised) register set: While the hardware exposes
both the new and legacy register sets, accesses to the model's legacy
register set will not be serviced (however the access will be logged).
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-3-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICv2 introduces a new CPU interface register GICC_DIR, which
allows an OS to split the "priority drop" and "deactivate interrupt"
parts of interrupt completion. Implement this register.
(Note that the register is at offset 0x1000 in the CPU interface,
which means it is on a different 4K page from all the other registers.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Sergey Fedorov <serge.fdrv@gmail.com>
Message-id: 1456854176-7813-1-git-send-email-peter.maydell@linaro.org
Using the return value to report errors is error prone:
- xics_alloc() returns -1 on error but spapr_vio_busdev_realize() errors
on 0
- xics_alloc_block() returns the unclear value of ics->offset - 1 on error
but both rtas_ibm_change_msi() and spapr_phb_realize() error on 0
This patch adds an errp argument to xics_alloc() and xics_alloc_block() to
report errors. The return value of these functions is a valid IRQ number
if errp is NULL. It is undefined otherwise.
The corresponding error traces get promotted to error messages. Note that
the "can't allocate IRQ" error message in spapr_vio_busdev_realize() also
moves to xics_alloc(). Similar error message consolidation isn't really
applicable to xics_alloc_block() because callers have extra context (device
config address, MSI or MSIX).
This fixes the issues mentioned above.
Based on previous work from Brian W. Hart.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Similar to the previous patch, it's nice to have all functions
in the tree that involve a visitor and a name for conversion to
or from QAPI to consistently stick the 'name' parameter next
to the Visitor parameter.
Done by manually changing include/qom/object.h and qom/object.c,
then running this Coccinelle script and touching up the fallout
(Coccinelle insisted on adding some trailing whitespace).
@ rule1 @
identifier fn;
typedef Object, Visitor, Error;
identifier obj, v, opaque, name, errp;
@@
void fn
- (Object *obj, Visitor *v, void *opaque, const char *name,
+ (Object *obj, Visitor *v, const char *name, void *opaque,
Error **errp) { ... }
@@
identifier rule1.fn;
expression obj, v, opaque, name, errp;
@@
fn(obj, v,
- opaque, name,
+ name, opaque,
errp)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-20-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
JSON uses "name":value, but many of our visitor interfaces were
called with visit_type_FOO(v, &value, name, errp). This can be
a bit confusing to have to mentally swap the parameter order to
match JSON order. It's particularly bad for visit_start_struct(),
where the 'name' parameter is smack in the middle of the
otherwise-related group of 'obj, kind, size' parameters! It's
time to do a global swap of the parameter ordering, so that the
'name' parameter is always immediately after the Visitor argument.
Additional reason in favor of the swap: the existing include/qjson.h
prefers listing 'name' first in json_prop_*(), and I have plans to
unify that file with the qapi visitors; listing 'name' first in
qapi will minimize churn to the (admittedly few) qjson.h clients.
Later patches will then fix docs, object.h, visitor-impl.h, and
those clients to match.
Done by first patching scripts/qapi*.py by hand to make generated
files do what I want, then by running the following Coccinelle
script to affect the rest of the code base:
$ spatch --sp-file script `git grep -l '\bvisit_' -- '**/*.[ch]'`
I then had to apply some touchups (Coccinelle insisted on TAB
indentation in visitor.h, and botched the signature of
visit_type_enum() by rewriting 'const char *const strings[]' to
the syntactically invalid 'const char*const[] strings'). The
movement of parameters is sufficient to provoke compiler errors
if any callers were missed.
// Part 1: Swap declaration order
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_start_struct
-(TV v, TObj OBJ, T1 ARG1, const char *name, T2 ARG2, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type bool, TV, T1;
identifier ARG1;
@@
bool visit_optional
-(TV v, T1 ARG1, const char *name)
+(TV v, const char *name, T1 ARG1)
{ ... }
@@
type TV, TErr, TObj, T1;
identifier OBJ, ARG1;
@@
void visit_get_next_type
-(TV v, TObj OBJ, T1 ARG1, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, TErr errp)
{ ... }
@@
type TV, TErr, TObj, T1, T2;
identifier OBJ, ARG1, ARG2;
@@
void visit_type_enum
-(TV v, TObj OBJ, T1 ARG1, T2 ARG2, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, T1 ARG1, T2 ARG2, TErr errp)
{ ... }
@@
type TV, TErr, TObj;
identifier OBJ;
identifier VISIT_TYPE =~ "^visit_type_";
@@
void VISIT_TYPE
-(TV v, TObj OBJ, const char *name, TErr errp)
+(TV v, const char *name, TObj OBJ, TErr errp)
{ ... }
// Part 2: swap caller order
@@
expression V, NAME, OBJ, ARG1, ARG2, ERR;
identifier VISIT_TYPE =~ "^visit_type_";
@@
(
-visit_start_struct(V, OBJ, ARG1, NAME, ARG2, ERR)
+visit_start_struct(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-visit_optional(V, ARG1, NAME)
+visit_optional(V, NAME, ARG1)
|
-visit_get_next_type(V, OBJ, ARG1, NAME, ERR)
+visit_get_next_type(V, NAME, OBJ, ARG1, ERR)
|
-visit_type_enum(V, OBJ, ARG1, ARG2, NAME, ERR)
+visit_type_enum(V, NAME, OBJ, ARG1, ARG2, ERR)
|
-VISIT_TYPE(V, OBJ, NAME, ERR)
+VISIT_TYPE(V, NAME, OBJ, ERR)
)
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1454075341-13658-19-git-send-email-eblake@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
This module is specific to the bcm2836 (Pi2). It implements the top
level interrupt controller, and mailboxes used for inter-processor
synchronisation.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-27-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-11-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-9-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-7-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-6-git-send-email-peter.maydell@linaro.org
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-5-git-send-email-peter.maydell@linaro.org
Update the GIC ID registers (registers above 0xfe0) based on the GIC
revision instead of using the sames values for all GIC implementations.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Message-id: 629e7fa5d47f2800e51cc1f18d12635f1eece349.1453333840.git.alistair.francis@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Device init() methods aren't supposed to call hw_error(), they should
report the error and fail cleanly. Do that.
The errors are all device misconfiguration. All callers use
qdev_init_nofail(), so this patch merely converts hw_error() crashes
into &error_abort crashes. Improvement, because now it crashes closer
to where the misconfiguration bug would be, and a few more bad
examples of hw_error() use are gone.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1450370121-5768-3-git-send-email-armbru@redhat.com>
This patch adds support for split IRQ chip mode. When
KVM_CAP_SPLIT_IRQCHIP is enabled:
1.) The PIC, PIT, and IOAPIC are implemented in userspace while
the LAPIC is implemented by KVM.
2.) The software IOAPIC delivers interrupts to the KVM LAPIC via
kvm_set_irq. Interrupt delivery is configured via the MSI routing
table, for which routes are reserved in target-i386/kvm.c then
configured in hw/intc/ioapic.c
3.) KVM delivers IOAPIC EOIs via a new exit KVM_EXIT_IOAPIC_EOI,
which is handled in target-i386/kvm.c and relayed to the software
IOAPIC via ioapic_eoi_broadcast.
Signed-off-by: Matt Gingell <gingell@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Upon activating an interrupt, set the corresponding priority bit in the
APR/NSAPR registers without touching the currently set bits. In the event
of nested interrupts, the GIC will then have the information it needs to
restore the priority of the pre-empted interrupt once the higher priority
interrupt finishes execution.
Signed-off-by: François Baldassari <francois@pebble.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
arm_gic.c retrieves CPU number using either NUM_CPU(s) or s->num_cpu.
Such mixed-uses make source code inconsistent. This patch removes
NUM_CPU(s), which was defined for MPCore tweak long ago, and instead
favors s->num_cpu. The source is more consistent after this small tweak.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Message-id: 1446744293-32365-1-git-send-email-wei@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the SYSRESETREQ bit of the AIRCR register
for armv7-m (ie. cortex-m3) to trigger a GPIO out.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The goal is to have debug code always compiled during build.
We standardize all debug output on the following format:
[QOM_TYPE_NAME]reporting_function: debug message
We also replace IPRINTF with qemu_log_mask(). The qemu_log_mask() output
is following the same format as the above debug.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 29885ffea2577eaf2288c1d17fd87ee951748b49.1445781957.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, if the kernel does not have live migration API, the migration
will still be attempted, but vGIC save/restore functions will just not do
anything. This will result in a broken machine state.
This patch fixes the problem by adding migration blocker if kernel API is
not supported.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
openpic is a programmable interrupt controller, so
add it to the misc category.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This should help clarify the purpose of the function that returns
the host system's CPU cycle count.
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
ppc portion
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
After CPU hotplug has been converted to BUS-less hot-plug infrastructure,
the only function ICC bus performs is to propagate reset to LAPICs. However
LAPIC could be reset by registering its reset handler after all device are
initialized.
Do so and drop ~30LOC of not needed anymore ICCBus related code.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When ICC bus/bridge is removed, APIC MMIO will be left
unmapped since it was mapped into system's address space
indirectly by ICC bridge.
Fix it by moving mapping into APIC code, so it would be
possible to remove ICC bus/bridge code later.
Signed-off-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Added support emulator for the hmp command "info ioapic"
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1442927901-1084-10-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Added prefix APIC_ for determining the constant of a particular subsystem,
improve the overall readability and match other constant names.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1442927901-1084-3-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move apic_get_bit(), apic_set_bit() to apic_internal.h, make the apic_get_ppr
symbol external. It's necessary to work with isr, tmr, irr and ppr outside
hw/intc/apic.c
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Andreas Färber <afaerber@suse.de>
Message-Id: <1442927901-1084-2-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The arbitration register should read to the same value as the
IOAPIC id register. Fixes kvm-unit-tests ioapic.flat.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If a level-triggered interrupt goes down and back up before the
corresponding EOI, it should be coalesced. This fixes one testcase
in kvm-unit-tests' ioapic.flat.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is the initial version of KVM-accelerated GICv3 support.
State load and save are not yet supported, live migration is
not possible.
In order to get correct class name in a simpler way, gicv3_class_name()
function is implemented, similar to gic_class_name().
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Message-id: 69d8f01d14994d7a1a140e96aef59fd332d02293.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some functions previously used only by vGICv2 are useful also for vGICv3
implementation. Untie them from GICState and make accessible from within
other modules:
- kvm_arm_gic_set_irq()
- kvm_gic_supports_attr() - moved to common code and renamed to
kvm_device_check_attr()
- kvm_gic_access() - turned into GIC-independent kvm_device_access().
Data pointer changed to void * because some GICv3 registers are
64-bit wide
Some of these changes are not used right now, but they will be helpful for
implementing live migration.
Actually kvm_dist_get() and kvm_dist_put() could also be made reusable, but
they would require two extra parameters (s->dev_fd and s->num_cpu) as well as
lots of typecasts of 's' to DeviceState * and back to GICState *. This makes
the code very ugly so i decided to stop at this point. I tried also an
approach with making a base class for all possible GICs, but it would contain
only three variables (dev_fd, cpu_num and irq_num), and accessing them through
the rest of the code would be again tedious (either ugly casts or qemu-style
separate object pointer). So i disliked it too.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 2ef56d1dd64ffb75ed02a10dcdaf605e5b8ff4f8.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This class is to be used by both software and KVM implementations of GICv3
Currently it is mostly a placeholder, but in future it is supposed to hold
qemu's representation of GICv3 state, which is necessary for migration.
The interface of this class is fully compatible with GICv2 one. This is
done in order to simplify integration with existing code.
Signed-off-by: Shlomo Pongratz <shlomo.pongratz@huawei.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Ashok kumar <ashoks@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: aff8baaee493cdcab0694b4a1d4dd5ff27c37ed2.1441784344.git.p.fedin@samsung.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A number of source files have statements accidentally
terminated by a double semicolon - eg 'foo = bar;;'.
This is harmless but a mistake none the less.
The tcg/ia64/tcg-target.c file is whitelisted because
it has valid use of ';;' in a comment containing assembly
code.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
If we directly boot a kernel in NonSecure on a system where the GIC
supports the security extensions then we must cause the GIC to
configure its interrupts into group 1 (NonSecure) rather than the
usual group 0, and with their initial priority set to the highest
NonSecure priority rather than the usual highest Secure priority.
Otherwise the guest kernel will be unable to use any interrupts.
Implement this behaviour, controlled by a flag which we set if
appropriate when the ARM bootloader code calls our ARMLinuxBootIf
interface callback.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1441383782-24378-4-git-send-email-peter.maydell@linaro.org
Although we were correctly handling interrupts becoming active
and then inactive, we weren't actually exposing this to the guest
by setting the 'active' flag for the interrupt, so reads
of GICD_ICACTIVERn and GICD_ISACTIVERn would generally incorrectly
return zeroes. Correct this oversight.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-6-git-send-email-peter.maydell@linaro.org
The running_irq and last_active arrays represent state which
doesn't exist in a real hardware GIC. The only thing we use
them for is updating the running priority when an interrupt
is completed, but in fact we can use the active-priority
registers to do this. The running priority is always the
priority corresponding to the lowest set bit in the active
priority registers, because only one interrupt at any
particular priority can be active at once.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-5-git-send-email-peter.maydell@linaro.org
A GICv2 has both GICC_APR<n> and GICC_NSAPR<n> registers, with
the latter holding the active priority bits for Group 1 interrupts
(usually Nonsecure interrupts), and the Nonsecure view of the
GICC_APR<n> is the second half of the GICC_NSAPR<n> registers.
Turn our half-hearted implementation of APR<n> into a proper
implementation of both APR<n> and NSAPR<n>:
* Add the underlying state for NSAPR<n>
* Make sure APR<n> aren't visible for pre-GICv2
* Implement reading of NSAPR<n>
* Make non-secure reads of APR<n> behave correctly
* Implement writing to APR<n> and NSAPR<n>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-4-git-send-email-peter.maydell@linaro.org
Priority values for the GIC are divided into a "group priority"
and a "subpriority" (with the division being determined by the
binary point register). The running priority is only determined
by the group priority of the active interrupts, not the
subpriority. In particular, this means that there can't be more
than one active interrupt at any particular group priority.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-3-git-send-email-peter.maydell@linaro.org
Change the implementation of the Interrupt Control and State Register
in the v7M NVIC to not use the running_irq and last_active internal
state fields in the GIC. These fields don't correspond to state in
a real GIC and will be removed soon.
The changes to the ICSR are:
* the VECTACTIVE field is documented as identical to the IPSR[8:0]
field, so implement it that way
* implement RETTOBASE via looking at the active state bits
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1438089748-5528-2-git-send-email-peter.maydell@linaro.org
When we add new adapter routes we call kvm_irqchip_add_route() for every
virtqueue and in the same step also do the KVM_SET_GSI_ROUTING ioctl.
This is unnecessary costly as the interface allows us to set multiple
routes in one go. Let's first add all routes to the table stored in the
global kvm_state and then do the ioctl to commit the routes to the
in-kernel irqchip.
This saves us several ioctls to the kernel where for each call a list
is reallocated and populated.
Signed-off-by: Jens Freimann <jfrei@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Extracted duplicated initialization code from SW-emulated and KVM GIC
implementations and put into gic_init_irqs_and_mmio()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Message-id: 8ea5b2781ef39cb5989420987fc73c70e377687d.1438758065.git.p.fedin@samsung.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When supporting CPU hot removal by parking the vCPU fd and reusing
it during hotplug again, there can be cases where we try to reenable
KVM_CAP_IRQ_XICS CAP for the vCPU for which it was already enabled.
Introduce a boolean member in ICPState to track this and don't
reenable the CAP if it was already enabled earlier.
Re-enabling this CAP should ideally work, but currently it results in
kernel trying to create and associate ICP with this vCPU and that
fails since there is already an ICP associated with it. Hence this
patch is needed to work around this problem in the kernel.
This change allows CPU hot removal to work for sPAPR.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The code for -machine pseries maintains a global sPAPREnvironment structure
which keeps track of general state information about the guest platform.
This predates the existence of the MachineState structure, but performs
basically the same function.
Now that we have the generic MachineState, fold sPAPREnvironment into
sPAPRMachineState, the pseries specific subclass of MachineState.
This is mostly a matter of search and replace, although a few places which
relied on the global spapr variable are changed to find the structure via
qdev_get_machine().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The arm_gic_kvm now calls kvm_irqchip_set_qemuirq_gsi to build
the hash table storing qemu_irq/gsi mappings. From that point on
irqfd can be setup directly from the qemu_irq using
kvm_irqchip_add_irqfd_notifier.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Vikram Sethi <vikrams@codeaurora.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The arm_gic_common reset function was missing reset code for
several of the GIC's state fields:
* bpr[]
* abpr[]
* priority1[]
* priority2[]
* sgi_pending[]
* irq_target[] (SMP configurations only)
These probably went unnoticed because most guests will either
never touch them, or will write to them in the process of
configuring the GIC before enabling interrupts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1435602345-32210-1-git-send-email-peter.maydell@linaro.org
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
These macros expand into error class enumeration constant, comma,
string. Unclean. Has been that way since commit 13f59ae.
The error class is always ERROR_CLASS_GENERIC_ERROR since the previous
commit.
Clean up as follows:
* Prepend every use of a QERR_ macro by ERROR_CLASS_GENERIC_ERROR, and
delete it from the QERR_ macro. No change after preprocessing.
* Rewrite error_set(ERROR_CLASS_GENERIC_ERROR, ...) into
error_setg(...). Again, no change after preprocessing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
This patch fixes so that gic_update always updates all the cores with
new pending irq states. If the function returns early it is possible
to get interrupts that has already been acknowledged.
Signed-off-by: Johan Karlsson <johan.karlsson@enea.com>
[PMM: rebased to apply to current master]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We create optional sections with this patch. But we already have
optional subsections. Instead of having two mechanism that do the
same, we can just generalize it.
For subsections we just change:
- Add a needed function to VMStateDescription
- Remove VMStateSubsection (after removal of the needed function
it is just a VMStateDescription)
- Adjust the whole tree, moving the needed function to the corresponding
VMStateDescription
Signed-off-by: Juan Quintela <quintela@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVbvwjAAoJEL7lnXSkw9fbaFwIAIh6PN5v6fvuEjnPX5ijHZC2
7iJoFd0I2cYrxgLe4xONFX9qzV5vgdEAJfXCljVCKAmzu5RK7G0ZSW81sJ3t6Mp8
kA8buJeyTp2UcTlDrC3qji8ScEIj+g8I9tKGflNVI2uDAVumMBPqnJNSFhbaqYlu
SEq+4y/D3J6xPzr7NhyHliG0NmxJrIn6QCtux5djj3xO4KXfp1j2YQCPKhYjkRlW
wHfqeD7x9LX6875FX3csgfPsYIycW0WYtba2adTe0vbTsclOY0CU3ho8HPeXgHE6
WQj6KYGT8Fo0zmK8UV0Jmok7+hZoxXXInf6vY+sSY58oe71FgdxNwLvIC6N0eQc=
=AALk
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mjt/tags/pull-trivial-patches-2015-06-03' into staging
trivial patches for 2015-06-03
# gpg: Signature made Wed Jun 3 14:07:47 2015 BST using RSA key ID A4C3D7DB
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>"
# gpg: aka "Michael Tokarev <mjt@corpit.ru>"
# gpg: aka "Michael Tokarev <mjt@debian.org>"
* remotes/mjt/tags/pull-trivial-patches-2015-06-03: (30 commits)
configure: postfix --extra-cflags to QEMU_CFLAGS
cadence_gem: Fix Rx buffer size field mask
slirp: use less predictable directory name in /tmp for smb config (CVE-2015-4037)
translate-all: delete prototype for non-existent function
Add -incoming help text
hw/display/tc6393xb.c: Fix misusing qemu_allocate_irqs for single irq
hw/arm/nseries.c: Fix misusing qemu_allocate_irqs for single irq
hw/alpha/typhoon.c: Fix misusing qemu_allocate_irqs for single irq
hw/unicore32/puv3.c: Fix misusing qemu_allocate_irqs for single irq
hw/lm32/milkymist.c: Fix misusing qemu_allocate_irqs for single irq
hw/lm32/lm32_boards.c: Fix misusing qemu_allocate_irqs for single irq
hw/ppc/prep.c: Fix misusing qemu_allocate_irqs for single irq
hw/sparc/sun4m.c: Fix misusing qemu_allocate_irqs for single irq
hw/timer/arm_timer.c: Fix misusing qemu_allocate_irqs for single irq
hw/isa/i82378.c: Fix misusing qemu_allocate_irqs for single irq
hw/isa/lpc_ich9.c: Fix misusing qemu_allocate_irqs for single irq
hw/i386/pc: Fix misusing qemu_allocate_irqs for single irq
hw/intc/exynos4210_gic.c: Fix memory leak by adjusting order
hw/arm/omap_sx1.c: Fix memory leak spotted by valgrind
hw/ppc/e500.c: Fix memory leak
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VKFL
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/x86-pull-request' into staging
X86 queue 2015-06-02
# gpg: Signature made Tue Jun 2 20:21:17 2015 BST using RSA key ID 984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-pull-request:
arch_init: Drop target-x86_64.conf
target-i386: Register QOM properties for feature flags
apic: convert ->busdev.qdev casts to C casts
target-i386: Fix signedness of MSR_IA32_APICBASE_BASE
pc: Ensure non-zero CPU ref count after attaching to ICC bus
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use C casts to avoid accessing ICCDevice's qdev field
directly.
Signed-off-by: Zhu Guihua <zhugh.fnst@cn.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
After introduction of kvm_arch_msi_data_to_gsi, kvm_gsi_direct_mapping
now can be set on ARM. Also kvm_msi_via_irqfd_allowed can be set,
depending on kernel irqfd support, hence enabling VIRTIO-PCI with
vhost back-end.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM GICv2m widget is a little device that handles MSI interrupt
writes to a trigger register and ties them to a range of interrupt lines
wires to the GIC. It has a few status/id registers and the interrupt wires,
and that's about it.
A board instantiates the device by setting the base SPI number and
number SPIs for the frame. The base-spi parameter is indexed in the SPI
number space only, so base-spi == 0, means IRQ number 32. When a device
(the PCI host controller) writes to the trigger register, the payload is
the GIC IRQ number, so we have to subtract 32 from that and then index
into our frame of SPIs.
When instantiating a GICv2m device, tell PCI that we have instantiated
something that can deal with MSIs. We rely on the board actually wiring
up the GICv2m to the PCI host controller.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-3-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support to gic_update() for determining the current IRQ
and FIQ status when interrupt grouping is supported. This
simply requires that instead of always raising IRQ we
check the group of the highest priority pending interrupt
and the GICC_CTLR.FIQEn bit to see whether we should raise
IRQ or FIQ.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1430502643-25909-15-git-send-email-peter.maydell@linaro.org
Grouping (GICv2) and Security Extensions change the behavior of IAR
reads. Acknowledging Group0 interrupts is only allowed from Secure
state and acknowledging Group1 interrupts from Secure state is only
allowed if AckCtl bit is set.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-14-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-14-git-send-email-greg.bellows@linaro.org
[PMM: simplify significantly by reusing the existing
gic_get_current_pending_irq() rather than reimplementing the
same logic here]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Grouping (GICv2) and Security Extensions change the behavior of EOIR
writes. Completing Group0 interrupts is only allowed from Secure state.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-13-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-13-git-send-email-greg.bellows@linaro.org
[PMM: Rather than go to great lengths to ignore the UNPREDICTABLE case
of a Secure EOI of a Group1 (NS) irq with AckCtl == 0, we just let
it fall through; add a comment about it.]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Grouping (GICv2) and Security Extensions change the behaviour of reads
of the highest priority pending interrupt register (ICCHPIR/GICC_HPPIR).
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-12-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-12-git-send-email-greg.bellows@linaro.org
[PMM: make utility fn static; coding style fixes; AckCtl has an effect
for GICv2 without security extensions as well; removed checks on enable
bits because these are done when we set current_pending[cpu]]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
GICs with Security Extensions restrict the non-secure view of the
interrupt priority and priority mask registers.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-11-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-15-git-send-email-greg.bellows@linaro.org
[PMM: minor code tweaks; fixed missing masking in gic_set_priority_mask
and gic_set_priority]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For GICs with Security Extensions Non-secure reads have a restricted
view on the current running priority.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-10-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-11-git-send-email-greg.bellows@linaro.org
[PMM: make function static, minor comment tweak]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ICCICR/GICC_CTLR is banked in GICv1 implementations with Security
Extensions or in GICv2 in independent from Security Extensions.
This makes it possible to enable forwarding of interrupts from
the CPU interfaces to the connected processors for Group0 and Group1.
We also allow to set additional bits like AckCtl and FIQEn by changing
the type from bool to uint32. Since the field does not only store the
enable bit anymore and since we are touching the vmstate, we use the
opportunity to rename the field to cpu_ctlr.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-9-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-9-git-send-email-greg.bellows@linaro.org
[PMM: rewrote to store state in a single uint32_t rather than
keeping the NS and S banked variants separate; this considerably
simplifies the get/set functions]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This register is banked in GICs with Security Extensions. Storing the
non-secure copy of BPR in the abpr, which is an alias to the non-secure
copy for secure access. ABPR itself is only accessible from secure state
if the GIC implements Security Extensions.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-8-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-10-git-send-email-greg.bellows@linaro.org
[PMM: rewrote to fix style issues and correct handling of GICv2
without security extensions]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ICDDCR/GICD_CTLR is banked if the GIC has the security extensions,
and the S (or only) copy has separate enable bits for Group0 and
Group1 enable if the GIC implements interrupt groups.
EnableGroup0 (Bit [1]) in GICv1 is architecturally IMPDEF. Since this
bit (Enable Non-secure) is present in the integrated GIC of the Cortex-A9
MPCore, we support this bit in our GICv1 implementation too.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-7-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-8-git-send-email-greg.bellows@linaro.org
[PMM: rewritten to store the state in a single s->ctlr uint32,
with the NS register handled as an alias of bit 1 in that value;
added vmstate version bump]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the GIC base class has state fields for the GICD_IGROUPRn
registers, make kvm_arm_gic_get() and kvm_arm_gic_put() write and
read them. This allows us to remove the check that made us
fail migration if the guest had set any of the group register bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-6-git-send-email-peter.maydell@linaro.org
The Interrupt Group Registers allow the guest to configure interrupts
into one of two groups, where Group0 are higher priority and may
be routed to IRQ or FIQ, and Group1 are lower priority and always
routed to IRQ. (In a GIC with the security extensions Group0 is
Secure interrupts and Group 1 is NonSecure.)
The GICv2 always supports interrupt grouping; the GICv1 does only
if it implements the security extensions.
This patch implements the ability to read and write the registers;
the actual functionality the bits control will be added in a
subsequent patch.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-5-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-7-git-send-email-greg.bellows@linaro.org
[PMM: bring GIC_*_GROUP macros into line with the others, ie a
simple SET/CLEAR/TEST rather than GROUP0/GROUP1;
utility gic_has_groups() function;
minor style fixes;
bump vmstate version]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the GIC's MMIO callback functions to the read_with_attrs
and write_with_attrs functions which provide MemTxAttrs. This will
allow the GIC to correctly handle secure and nonsecure register
accesses.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1430502643-25909-4-git-send-email-peter.maydell@linaro.org
Add a QOM property which allows the GIC Security Extensions to be
enabled. These are an optional part of the GICv1 and GICv2 architecture.
This commit just adds the property and some sanity checks that it
is only enabled on GIC revisions that support it.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-3-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-5-git-send-email-greg.bellows@linaro.org
[PMM: changed property name, added checks that it isn't set for
older GIC revisions or if using the KVM VGIC; reworded commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create the outbound FIQ lines from the GIC to the CPUs; these are
used if the GIC has security extensions or grouping support.
Signed-off-by: Fabian Aggeler <aggelerf@ethz.ch>
Signed-off-by: Greg Bellows <greg.bellows@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1430502643-25909-2-git-send-email-peter.maydell@linaro.org
Message-id: 1429113742-8371-2-git-send-email-greg.bellows@linaro.org
[PMM: added FIQ lines to kvm-arm-gic so its interface is the same;
tweaked commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Consider the following pseudo code to configure SYSTICK (The
recommended programming sequence from "the definitive guide to the
arm cortex-m3"):
SYSTICK Reload Value Register = 0xffff
SYSTICK Current Value Register = 0
SYSTICK Control and Status Register = 0x7
The pseudo code "SYSTICK Current Value Register = 0" leads to invoking
systick_reload(). As a consequence, the systick.tick member is updated
and the systick timer starts to count down when the ENABLE bit of
SYSTICK Control and Status Register is cleared.
The worst case is that: during the system initialization, the reset
value of the SYSTICK Control and Status Register is 0x00000000.
When the code "SYSTICK Current Value Register = 0" is executed, the
systick.tick member is accumulated with "(s->systick.reload + 1) *
systick_scale(s)". The systick_scale() gets the external_ref_clock
scale because the CLKSOURCE bit of the SYSTICK Control and Status
Register is cleared. This is the incorrect behavior because of the
code "SYSTICK Control and Status Register = 0x7". Actually, we want
the processor clock instead of the external reference clock.
This incorrect behavior defers the generation of the first interrupt.
The patch fixes the above-mentioned issue by setting the systick.tick
member and modifying the systick timer only if the ENABLE bit of
the SYSTICK Control and Status Register is set.
In addition, the Cortex-M3 Devices Generic User Guide mentioned that
"When ENABLE is set to 1, the counter loads the RELOAD value from the
SYST RVR register and then counts down". This patch adheres to the
statement of the user guide.
Signed-off-by: Adrian Huang <adrianhuang0701@gmail.com>
Reviewed-by: Jim Huang <jserv.tw@gmail.com>
[PMM: minor tweak to comment text]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace call of cpu_is_bsp(s->cpu) which really returns
!!(s->apicbase & MSR_IA32_APICBASE_BSP)
with directly collected value. Due to this the tracepoint
trace_cpu_get_apic_base((uint64_t)s->apicbase);
will not be hit anymore in apic_reset_common.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Andreas Färber <afaerber@suse.de>
CC: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1428414832-3104-1-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- next part in the thread-safe address_space_* saga: atomic access
to the bounce buffer and the map_clients list, from Fam
- optional support for linking with tcmalloc, also from Fam
- reapplying Peter Crosthwaite's "Respect as_translate_internal
length clamp" after fixing the SPARC fallout.
- build system fix from Wei Liu
- small acpi-build and ioport cleanup by myself
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJVQJd4AAoJEL/70l94x66DYFYH/3ifhqWZsd4dfJri0CGAHI4i
SpPmNeouc8W+F/3lwf6Inrh5NnTgd5QzoUBMQaWVkQKwUiWls8g2mXkT3jo0iDqT
/B40YXnZjNm20MixNaZmk9AsOF6OqPM8EMufau874k5zTlx3tCGAW1QD+I1N7WK7
DfsFsIUD1svo2prn55fSoitMG1TIVPnpcklb4YGJRbAacQYUDhr5KAIhT1quDR2R
93BvToyQmPqRQ4YKqnJLp8HAkL4FaJumfFZVvyh2cZvyaYGN/RVdi2Dw985dJDPX
/z4enE4GCAs4RDw3lZ1RDbiZDqpT2ibFgASg/arX3SxzqHirOGvMdkOjO99r9j4=
=aLjh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
- miscellaneous cleanups for TCG (Emilio) and NBD (Bogdan)
- next part in the thread-safe address_space_* saga: atomic access
to the bounce buffer and the map_clients list, from Fam
- optional support for linking with tcmalloc, also from Fam
- reapplying Peter Crosthwaite's "Respect as_translate_internal
length clamp" after fixing the SPARC fallout.
- build system fix from Wei Liu
- small acpi-build and ioport cleanup by myself
# gpg: Signature made Wed Apr 29 09:34:00 2015 BST using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (22 commits)
nbd/trivial: fix type cast for ioctl
translate-all: use bitmap helpers for PageDesc's bitmap
target-i386: disable LINT0 after reset
Makefile.target: prepend $libs_softmmu to $LIBS
milkymist: do not modify libs-softmmu
configure: Add support for tcmalloc
exec: Respect as_translate_internal length clamp
ioport: reserve the whole range of an I/O port in the AddressSpace
ioport: loosen assertions on emulation of 16-bit ports
ioport: remove wrong comment
ide: there is only one data port
gus: clean up MemoryRegionPortio
sb16: remove useless mixer_write_indexw
sun4m: fix slavio sysctrl and led register sizes
acpi-build: remove dependency from ram_addr.h
memory: add memory_region_ram_resize
dma-helpers: Fix race condition of continue_after_map_failure and dma_aio_cancel
exec: Notify cpu_register_map_client caller if the bounce buffer is available
exec: Protect map_client_list with mutex
linux-user, bsd-user: Remove two calls to cpu_exec_init_all
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Due to old Seabios bug, QEMU reenable LINT0 after reset. This bug is long gone
and therefore this hack is no longer needed. Since it violates the
specifications, it is removed.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1428881529-29459-2-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rewrite the loop using level &= level - 1 to clear the least significant
bit after each iteration. This simplifies the loop and makes it easy to
replace ffs(3) with ctz32().
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-8-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
There are a number of ffs(3) callers that do roughly:
bit = ffs(val);
if (bit) {
do_something(bit - 1);
}
This pattern can be converted to ctz32() like this:
zeroes = ctz32(val);
if (zeroes != 32) {
do_something(zeroes);
}
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-6-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since the BSP bit is writable on real hardware, during reset all the CPUs which
were not chosen to be the BSP should have their BSP bit cleared. This fix is
required for KVM to work correctly when it changes the BSP bit.
An additional fix is required for QEMU tcg to allow software to change the BSP
bit.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427932716-11800-1-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As there is logic to deal with the difference between edge and level
triggered interrupts in the kernel we must ensure it knows the
configuration of the IRQs before we restore the pending state.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* fix handling of execute-never bits in page table walks
* tell kernel to initialize KVM GIC in realize function
* fix handling of STM (user) with r15 in register list
* ignore low bit of PC in M-profile exception return
* fix linux-user get/set_tls syscalls on CPUs with TZ
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uK1h
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20150316' into staging
target-arm queue:
* fix handling of execute-never bits in page table walks
* tell kernel to initialize KVM GIC in realize function
* fix handling of STM (user) with r15 in register list
* ignore low bit of PC in M-profile exception return
* fix linux-user get/set_tls syscalls on CPUs with TZ
# gpg: Signature made Mon Mar 16 12:39:04 2015 GMT using RSA key ID 14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
* remotes/pmaydell/tags/pull-target-arm-20150316:
linux-user: Access correct register for get/set_tls syscalls on ARM TZ CPUs
target-arm: Ignore low bit of PC in M-profile exception return
target-arm: Fix handling of STM (user) with r15 in register list
hw/intc/arm_gic: Initialize the vgic in the realize function
target-arm: get_phys_addr_lpae: more xn control
target-arm: fix get_phys_addr_v6/SCTLR_AFE access check
target-arm: convert check_ap to ap_to_rw_prot
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch forces vgic initialization in the vgic realize function.
It uses a new group/attribute that allows such operation:
KVM_DEV_ARM_VGIC_GRP_CTRL/KVM_DEV_ARM_VGIC_CTRL_INIT
This earlier initialization allows, for example, to setup VFIO
signaling and irqfd after vgic initialization, on a reset notifier.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Message-id: 1426094226-8515-1-git-send-email-eric.auger@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
s390_flic_init() is a helper to create and realize either
"s390-flic-kvm" or "s390-flic-qemu". When qdev_init() fails, it
complains to stderr and succeeds.
Except it can't actually fail, because the "s390-flic-qemu" is a dummy
without a realize method, and "s390-flic-kvm"'s realize can't fail,
even when the kernel device is really unavailable. Odd.
Replace qdev_init() by qdev_init_nofail() to make "can't fail" locally
obvious, and get rid of the unreachable error reporting.
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Message-Id: <1423128889-18260-4-git-send-email-armbru@redhat.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is in preparation for using VMSTATE_BITMAP in a followup vmstate
migration patch.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Alexander Graf <agraf@suse.de>
Issuing loadvm under -M mac99 would fail for two reasons: firstly an incorrect
version number for openpic would cause openpic_load() to abort, and secondly
a cut/paste error when restoring the IVPR and IDR registers caused subsequent
vmstate sections to become misaligned and abort early.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Alexander Graf <agraf@suse.de>
A simple copy/paste error causes savevm on -M mac99 to segfault.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Alexander Graf <agraf@suse.de>
Some are called do_info_SUBCOMMAND() (old ones, usually), some
hmp_info_SUBCOMMAND(), some SUBCOMMAND_info(), sometimes SUBCOMMAND
pointlessly differs in spelling.
Normalize to hmp_info_SUBCOMMAND(), where SUBCOMMAND is exactly the
subcommand name with '-' replaced by '_'.
Exceptions:
* sun4m_irq_info(), sun4m_pic_info() renamed to sun4m_hmp_info_irq(),
sun4m_hmp_info_pic().
* lm32_irq_info(), lm32_pic_info() renamed to lm32_hmp_info_irq(),
lm32_hmp_info_pic().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Right now you only get to apic_init_reset if you have an APIC
(do_cpu_init is reached only if CPU_INTERRUPT_INIT is set and
that only happens in hw/intc/apic.c). However, this is wrong
because for example a port 92 or keyboard controller reset is
really an INIT, and that can happen also with no APIC. So
keep the check and fix the error that Coverity reported.
Reported-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- valgrind/KVM support
- small i386 patches
- PCI SD host controller support
- malloc/free cleanups from Markus (x86/scsi)
- IvyBridge model
- XSAVES support for KVM
- initial patches from record/replay
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUjw28AAoJEL/70l94x66D9kcH/RBoc4mNjrSt+MLy9Y+Fu1bu
HNhfd1n/yA0MKSHtSYwJPgkiuoxG3jHt0N69gbpZE0kdBcK+PPZZZUpTFIAU6vD/
D0O7l+2viOcl2z7SPuHIp9/O0CChsAYZkH+Zn2XbeStbe4d4f6bFzdy4vblMsirQ
BfMn/Y2Dw1uLknvrO3/QKgGhbK5Nxo/Te7lavRP+w7FgOhAdAUHOhBPfGrPWtG+0
0hVWmxoQyJtk+Ltt2oF4zUkql7czDsgyXkaO82l3TkecCvtqolCuby4lQIFJnq7E
vw0XUDwC/l/MWnXFq/rG97yopfIxkSAthT/xP/+TTJKM/oJEWDTh6I8ghQTdG90=
=ncys
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
- Migration and linuxboot fixes for 2.2 regressions
- valgrind/KVM support
- small i386 patches
- PCI SD host controller support
- malloc/free cleanups from Markus (x86/scsi)
- IvyBridge model
- XSAVES support for KVM
- initial patches from record/replay
# gpg: Signature made Mon 15 Dec 2014 16:35:08 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (47 commits)
sdhci: Support SDHCI devices on PCI
sdhci: Define SDHCI PCI ids
sdhci: Add "sysbus" to sdhci QOM types and methods
sdhci: Remove class "virtual" methods
sdhci: Set a default frequency clock
serial: only resample THR interrupt on rising edge of IER.THRI
serial: update LSR on enabling/disabling FIFOs
serial: clean up THRE/TEMT handling
serial: reset thri_pending on IER writes with THRI=0
linuxboot: fix loading old kernels
kvm/apic: fix 2.2->2.1 migration
target-i386: add Ivy Bridge CPU model
target-i386: add f16c and rdrand to Haswell and Broadwell
target-i386: add VME to all CPUs
pc: add 2.3 machine types
i386: do not cross the pages boundaries in replay mode
cpus: make icount warp behave well with respect to stop/cont
timer: introduce new QEMU_CLOCK_VIRTUAL_RT clock
cpu-exec: invalidate nocache translation if they are interrupted
icount: introduce cpu_get_icount_raw
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The wait_for_sipi field is set back to 1 after an INIT, so it was not
effective to reset it in kvm_apic_realize. Introduce a reset callback
and reset wait_for_sipi there.
Reported-by: Igor Mammedov <imammedo@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Compute kvm_irqfds_allowed by checking the KVM_CAP_IRQFD extension.
Remove direct settings in architecture specific files.
Add a new kvm_resamplefds_allowed variable, initialized by
checking the KVM_CAP_IRQFD_RESAMPLE extension. Add a corresponding
kvm_resamplefds_enabled() function.
A special notice for s390 where KVM_CAP_IRQFD was not immediatly
advirtised when irqfd capability was introduced in the kernel.
KVM_CAP_IRQ_ROUTING was advertised instead.
This was fixed in "KVM: s390: announce irqfd capability",
ebc3226202d5956a5963185222982d435378b899 whereas irqfd support
was brought in 84223598778ba08041f4297fda485df83414d57e,
"KVM: s390: irq routing for adapter interrupts". Both commits
first appear in 3.15 so there should not be any kernel
version impacted by this QEMU modification.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Newer kernels support a device attribute on the GIC which allows us to
tell it how many IRQs this GIC instance is configured with; use it, if
it exists.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1417718679-1071-1-git-send-email-peter.maydell@linaro.org
This fixes another failure with ExtINT, demonstrated by QNX. The failure
mode is as follows:
- IPI sent to cpu 0 (bit set in APIC irr)
- IPI accepted by cpu 0 (bit cleared in irr, set in isr)
- IPI sent to cpu 0 (bit set in both irr and isr)
- PIC interrupt sent to cpu 0
The PIC interrupt causes CPU_INTERRUPT_HARD to be set, but
apic_irq_pending observes that the highest pending APIC interrupt priority
(the IPI) is the same as the processor priority (since the IPI is still
being handled), so apic_get_interrupt returns a spurious interrupt rather
than the pending PIC interrupt. The result is an endless sequence of
spurious interrupts, since nothing will clear CPU_INTERRUPT_HARD.
Instead, ExtINT interrupts should have ignored the processor priority.
Calling apic_check_pic early in apic_get_interrupt ensures that
apic_deliver_pic_intr is called instead of delivering the spurious
interrupt. apic_deliver_pic_intr then clears CPU_INTERRUPT_HARD if needed.
Reported-by: Richard Bilson <rbilson@qnx.com>
Tested-by: Richard Bilson <rbilson@qnx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch fixes an obscure failure of the QNX kernel on QEMU x86 SMP.
In QNX, all hardware interrupts come via the PIC, and are delivered by
the cpu 0 LAPIC in ExtINT mode, while IPIs are delivered by the LAPIC
in fixed mode.
This bug happens as follows:
- cpu 0 masks a particular PIC interrupt
- IPI sent to cpu 0 (CPU_INTERRUPT_HARD is set)
- before the IPI is accepted, the masked interrupt line is asserted by the
device
Since the interrupt is masked, apic_deliver_pic_intr will clear
CPU_INTERRUPT_HARD. The IPI will still be set in the APIC irr, but since
CPU_INTERRUPT_HARD is not set the cpu will not notice. Depending on the
scenario this can cause a system hang, i.e. if cpu 0 is expected to unmask
the interrupt.
In order to fix this, do a full check of the APIC before an EXTINT
is acknowledged. This can result in clearing CPU_INTERRUPT_HARD, but
can also result in delivering the lost IPI.
Reported-by: Richard Bilson <rbilson@qnx.com>
Tested-by: Richard Bilson <rbilson@qnx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
After the next patch, if a masked PIC interrupts causes CPU_INTERRUPT_POLL
to be set, the CPU will spuriously get out of halted state. While this
is technically valid, we should avoid that.
Make CPU_INTERRUPT_POLL run apic_update_irq in the right thread and then
look at CPU_INTERRUPT_HARD. If CPU_INTERRUPT_HARD does not get set,
do not report the CPU as having work.
Also move the handling of software-disabled APIC from apic_update_irq
to apic_irq_pending, and always trigger CPU_INTERRUPT_POLL. This will
be important once we will add a case that resets CPU_INTERRUPT_HARD
from apic_update_irq. We want to run it even if we go through
CPU_INTERRUPT_POLL, and even if the local APIC is software disabled.
Reported-by: Richard Bilson <rbilson@qnx.com>
Tested-by: Richard Bilson <rbilson@qnx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds missed sipi_vector and wait_for_sipi fields to a new
subsection of the vmstate of the apic_common module. Saving and loading
of these fields makes migration of the apic state deterministic.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
[Initialize the field in pre_load and kvm_apic_realize. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The in-kernel OpenPIC emulation only supports a single map. However, we
map the OpenPIC at 2 locations: The CPU visible one and the PCI visible
one. For KVM acceleration, we only care about the first one.
To make sure that we only map that first mapping and not the PCI map that
happens dynamically later during bootup, ignore maps that happen when
we are already considering ourselves mapped.
Credits due are to Bogdan and Mihai for debugging this.
Reported-by: Bogdan Purcareata <bogdan.purcareata@freescale.com>
Reported-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This removes num_irq parameter from gic_init_irqs_and_distributor as it is not
used.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1412859651-15060-1-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Steps:
1.enable qemu debug print, using simply scprit as below:
grep "//#define DEBUG" * -rl | xargs sed -i "s/\/\/#define DEBUG/#define DEBUG/g"
2. make -j
3. get some warning:
hw/i2c/pm_smbus.c: In function 'smb_ioport_writeb':
hw/i2c/pm_smbus.c:142: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/i2c/pm_smbus.c:142: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/i2c/pm_smbus.c: In function 'smb_ioport_readb':
hw/i2c/pm_smbus.c:209: warning: format '%04x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/intc/i8259.c: In function 'pic_ioport_read':
hw/intc/i8259.c:373: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/input/pckbd.c: In function 'kbd_write_command':
hw/input/pckbd.c:232: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
hw/input/pckbd.c: In function 'kbd_write_data':
hw/input/pckbd.c:333: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
hw/isa/apm.c: In function 'apm_ioport_writeb':
hw/isa/apm.c:44: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/isa/apm.c:44: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/isa/apm.c: In function 'apm_ioport_readb':
hw/isa/apm.c:67: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'hwaddr'
hw/timer/mc146818rtc.c: In function 'cmos_ioport_write':
hw/timer/mc146818rtc.c:394: warning: format '%02x' expects type 'unsigned int', but argument 3 has type 'uint64_t'
hw/i386/pc.c: In function 'port92_write':
hw/i386/pc.c:479: warning: format '%02x' expects type 'unsigned int', but argument 2 has type 'uint64_t'
Fix them.
Cc: qemu-trivial@nongnu.org
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Take IRQ target mask into account when determining the highest priority
pending interrupt.
Signed-off-by: Sergey Fedorov <serge.fdrv@gmail.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1407947471-26981-1-git-send-email-serge.fdrv@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use constant rather than a plain number.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-5-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only SGIs must be WI, done by forcing them to their default
(edge-triggered).
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-4-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Setting the model is only available in pre-v1 GIC models.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-3-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GICD_ICFGR register covers 4 interrupts per byte.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Adam Lackorzynski <adam@os.inf.tu-dresden.de>
Message-id: 1408372255-12358-2-git-send-email-adam@os.inf.tu-dresden.de
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To be more array friendly and to indicate the IRQs are initially
disconnected.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
To indicate the IRQs are initially disconnected.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
This implements interrupt release function so IRQs can be returned back
to the pool for reuse in cases such as PCI hot plug.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current allocator returns IRQ numbers from a pool and does not
support IRQs reuse in any form as it did not keep track of what it
previously returned, it only keeps the last returned IRQ. Some use
cases such as PCI hot(un)plug may require IRQ release and reallocation.
This moves an allocator from SPAPR to XICS.
This switches IRQ users to use new API.
This uses LSI/MSI flags to know if interrupt is allocated.
The interrupt release function will be posted as a separate patch.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since islsi[] array has been merged into the ICSState struct,
we must not reset flags as they tell if the interrupt is in use.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
PAPR allows having multiple interrupt sources such as PHB.
This adds a source lookup function and makes use of it.
Since at the moment QEMU only supports a single source,
no change in behaviour is expected.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
The existing interrupt allocation scheme in SPAPR assumes that
interrupts are allocated at the start time, continously and the config
will not change. However, there are cases when this is not going to work
such as:
1. migration - we will have to have an ability to choose interrupt
numbers for devices in the command line and this will create gaps in
interrupt space.
2. PCI hotplug - interrupts from unplugged device need to be returned
back to interrupt pool, otherwise we will quickly run out of interrupts.
This replaces a separate lslsi[] array with a byte in the ICSIRQState
struct and defines "LSI" and "MSI" flags. Neither of these flags set
signals that the descriptor is not allocated and not in use.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
At the moment spapr_rtas_register() allocates a new token number for every
new RTAS callback so numbers are not fixed and depend on the number of
supported RTAS handlers and the exact order of spapr_rtas_register() calls.
These tokens are copied into the device tree and remain the same during
the guest lifetime.
When we start another guest to receive a migration, it calls
spapr_rtas_register() as well. If the number of RTAS handlers or their
order is different in QEMU on source and destination sides, the "/rtas"
node in the device tree will differ. Since migration overwrites the device
tree (as it overwrites the entire RAM), the actual RTAS config on
the destination side gets broken.
This defines global contant values for every RTAS token which QEMU
is using today.
This changes spapr_rtas_register() to accept a token number instead of
allocating one. This changes all users of spapr_rtas_register().
This changes XICS-KVM not to cache tokens registered with KVM as they
constant now.
This makes TOKEN_BASE global as RTAS_XXX use TOKEN_BASE as
a base. TOKEN_MAX is moved and renamed too and its value is changed
to the last token + 1. Boundary checks for token values are adjusted.
This reserves token numbers for "os-term" handlers and PCI hotplug
which we are working on.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
The returned reset value was wrong (off by one zero nibble), and
qemu didn't log unimplemented writes to the PRIGROUP field.
Signed-off-by: Oran Avraham <oranav@gmail.com>
Message-id: 1403010447-4627-1-git-send-email-oranav@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When we trigger a system reset, the in-kernel openpic controller should also
get reset. This happens through a write to the GCR.RESET register which is
the same mechanism a guest would use to manually reset the device.
Signed-off-by: Alexander Graf <agraf@suse.de>
The openpic emulation code maintains an allowable-CPU's bitmap
("destmask") for each IRQ source which is calculated from the IDR
register value whenever the guest OS writes to it. However, if the
guest OS relies on the system to set the IDR register to a default
value at reset, and does not write IDR, then destmask does not get
updated, and interrupts do not get propagated to the guest.
Additionally, if an IRQ source is marked as critical, the source's
internal "output" and "nomask" fields are not correctly reset when the
PIC is reset.
Fix both these issues by calling write_IRQreg_idr from within
openpic_reset, instead of simply setting the IDR register to the
specified idr_reset value.
Signed-off-by: Paul Janzen <pcj@pauljanzen.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch moves the definition of openpic_reset after the various
register read/write functions. No functional change. It is in
preparation for using the register read/write functions in
openpic_reset.
Signed-off-by: Paul Janzen <pcj@pauljanzen.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Acked-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Hervé Poussineau
Peter Xu
Nikunj A Dadhania
Wanpeng Li
Greg Kurz
Cornelia Huck
Laurent Vivier
Peter Maydell
Igor Mammedov
Markus Armbruster
Yongbok Kim
Andrey Smirnov
Benjamin Herrenschmidt
Shannon Zhao
Daniel P. Berrange
xiaoqiang zhao
Eduardo Habkost
Shlomo Pongratz
Pavel Fedin
Bharata B Rao
Halil Pasic
Jens Wiklander
Paolo Bonzini
Hollis Blanchard
Rutuja Shah
Andrew Jeffery
Michael S. Tsirkin
Greg Kurz
Eric Blake
Andrew Baumann
Alistair Francis
François Baldassari
Wei Huang
Michael Davidsaver
Jean-Christophe Dubois
Laurent Vivier
Christopher Covington
Chen Fan
Pavel Butsykin
Veres Lajos
Jens Freimann
David Gibson
Eric Auger
Johan Karlsson
Juan Quintela
Zhu Guihua
Christoffer Dall
Fabian Aggeler
Adrian Huang
Denis V. Lunev
Nadav Amit
Stefan Hajnoczi
Alex Bennée
Stefan Weil
Mark Cave-Ayland
Fabien Chouteau
Pavel Dovgalyuk
Alexander Graf
KONRAD Frederic
Gonglei
Sergey Fedorov
Adam Lackorzynski
Peter Crosthwaite
Jan Kiszka
Alexey Kardashevskiy
Oran Avraham
Paul Janzen