Fix uninitialized value issues reported by Coverity:
Field 'msg.reserved' is uninitialized when calling write().
Fixes: a5bd05800f ("vhost-vdpa: batch updating IOTLB mappings")
Reported-by: Coverity (CID 1432864: UNINIT)
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20201028154004.776760-1-philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
According to PCIe spec 5.0 Type 1 header space Base Address Registers
are defined by 7.5.1.2.1 Base Address Registers (same as Type 0). The
_CRS region should allow for the same range (up to 64b). Prior to this
change, any host bridge utilizing more than 32b for the BAR would have
the address truncated and likely lead to conflicts when the operating
systems reads the _CRS object.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Message-Id: <20201026193924.985014-2-ben.widawsky@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Prevent _CRS resources being quietly chopped off and instead throw an
assertion. _CRS is used by host bridges to declare regions of io and/or
memory that they consume. On some (all?) platforms the host bridge
doesn't have PCI header space and so they need some way to convey the
information.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Message-Id: <20201026193924.985014-1-ben.widawsky@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
vhost IOTLB API uses read()/write() to exchange iotlb messages with
the kernel module.
The QEMU implementation expects a non-blocking fd, indeed commit
c471ad0e9b ("vhost_net: device IOTLB support") set it for vhost-net.
Without this patch, if we enable iommu for the vhost-vsock device,
QEMU can hang when exchanging IOTLB messages.
As commit 894022e616 ("net: check if the file descriptor is valid
before using it") did for tap, let's use qemu_try_set_nonblock()
when fd is provided by the user.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20201029144849.70958-1-sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Vendor driver may not support or implement config
interrupt delivery for link status notifications.
In this event, vendor driver is expected to NACK
the feature, but guest will keep link always up.
Signed-off-by: Si-Wei Liu <si-wei.liu@oracle.com>
Message-Id: <1601582985-14944-1-git-send-email-si-wei.liu@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
- add some more individual contributors
- include SDL2 in centos images
- skip checkpatch check when no commits found
- use random port for gdb reverse debugging
- make gitlab use it's own mirrors to clone
- fix detection of make -nqp
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAl+X7qsACgkQ+9DbCVqe
KkSpmAf/To0P/c/B6qMEvNfCiWtn/Nuypau8W60q/ZvE/J4IzFarwa5uc7COmyNR
xjvxdoeKp17ykFdwBzGhiKeO83SO8DUH1JmzA6STs4RH5VSFGYycuE0cQ9KugrpE
4yOruOdEgAn2+35oYalE9u6/EugdIVBZsjMS/ofsgR9ysYPuju4Q9by6DEK6ArW0
AmdwJzKAYw75v+D2wKNq9coSWvbqWClsV6j0gaKgn+OQYqWo25T/DzWdr1okCRET
TvB0HZLCDQHz9Friq5PtBtVsmNbZaL+CM9RRekFBGUFEvZE8i4VEDHFfzXsN3U0w
VA5yhlBJzl1/prBQe1qRbrZQL4x58w==
=Bnt1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-and-misc-271020-1' into staging
Testing and gitdm updates
- add some more individual contributors
- include SDL2 in centos images
- skip checkpatch check when no commits found
- use random port for gdb reverse debugging
- make gitlab use it's own mirrors to clone
- fix detection of make -nqp
# gpg: Signature made Tue 27 Oct 2020 09:55:55 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-and-misc-271020-1:
makefile: handle -n / -k / -q correctly
gitlab-ci: Clone from GitLab itself
tests/acceptance: pick a random gdb port for reverse debugging
scripts: fix error from checkpatch.pl when no commits are found
gitlab: skip checkpatch.pl checks if no commit delta on branch
tests/docker/dockerfiles/centos: Use SDL2 instead of SDL1
contrib/gitdm: Add more individual contributors
Adding ani's email as an individual contributor
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This reverts the following commits due to their basis on a bogus
linux kernel header update:
c93a656f7b ("tests/acceptance: Add virtiofs_submounts.py")
45ced7ca2f ("tests/acceptance/boot_linux: Accept SSH pubkey")
08dce386e7 ("virtiofsd: Announce sub-mount points")
eba8b096c1 ("virtiofsd: Store every lo_inode's parent_dev")
ede24b6be7 ("virtiofsd: Add fuse_reply_attr_with_flags()")
e2577435d3 ("virtiofsd: Add attr_flags to fuse_entry_param")
2f10415abf ("virtiofsd: Announce FUSE_ATTR_FLAGS")
97d741cc96 ("linux/fuse.h: Pull in from Linux")
Cc: Max Reitz <mreitz@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Message-id: 160385090886.20017.13382256442750027666.stgit@gimli.home
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
CI jobs results:
. https://cirrus-ci.com/build/4879251751043072
. https://gitlab.com/philmd/qemu/-/pipelines/207661784
. https://travis-ci.org/github/philmd/qemu/builds/738958191
. https://app.shippable.com/github/philmd/qemu/runs/891/summary/console
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAl+XR88ACgkQ4+MsLN6t
wN4Org//UPv8cTDvJwsS2vaw0CRHQmU7/t2hI6xN1mDMFaUDwj6AjtdO6W3FUOcV
KQbwFP16Po684h4xhDayUs15RcPz/mCSaiiz4WkS3sA5M0y0SWQE+1HgvGZwrEXn
o5j8Lilh8m4/WE97Q7hVPD2cesMv9W3EziWBMEqukaXCSnTfAURiUUWmXpu7jyQ8
tc439KhFXnLx6Gx/XyPoN2CLfC5q1OReGTGvAP2GqFDPxPnIAGyqHLaVOZBXlX3a
PsRl9HKvuPL86zrSXLRqsnUiiQ5vHg0Quw4jntd+ZF+V97Qlg01x0BuxI2+9GqO4
b/RVBbvrLdWEpmKffr6EsmNNLaREeTfjQWVowD2uy3IK6JxkG7oiljAj7sDySSzs
WYo8PCE/xpTtrtbLZNtRkkz3Ui/h0Qjdvi8oS/8k84/0/+fDufWekXz1pX6YZ4jI
2GK+aa/OrTZQh5uUYdzQPxf0ieviOVCSf0IgKvHkOlAqnZIQRkFmtIOdPyNlctQx
cGNMT9pgz+n4g1ge9LaBlyAMwxCGkU5nygbbPyYHGZyN8xiDNUKOAMRhXgLiKpXb
tbseixu4TDGr2iuc291G9dkeKbPkxeIE3NIbFwcB4UtTftxLko7pTZ5l3G0jvUt1
VCfK1ot6DKO8B+TzXyIgAWiZmWSV8KhHA4EkX4BihqLL3hIvlNk=
=inaF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/led-api-20201026' into staging
API to model LED.
CI jobs results:
. https://cirrus-ci.com/build/4879251751043072
. https://gitlab.com/philmd/qemu/-/pipelines/207661784
. https://travis-ci.org/github/philmd/qemu/builds/738958191
. https://app.shippable.com/github/philmd/qemu/runs/891/summary/console
# gpg: Signature made Mon 26 Oct 2020 22:03:59 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/led-api-20201026:
hw/arm/tosa: Replace fprintf() calls by LED devices
hw/misc/mps2-scc: Use the LED device
hw/misc/mps2-fpgaio: Use the LED device
hw/arm/aspeed: Add the 3 front LEDs drived by the PCA9552 #1
hw/misc/led: Emit a trace event when LED intensity has changed
hw/misc/led: Allow connecting from GPIO output
hw/misc/led: Add a LED device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Misono
Set default log level to info
Explicit build option for virtiofsd
Me
xattr name mapping
Stefan
Alternative chroot sandbox method
Max
Submount mechanism
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----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=dTCm
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert-gitlab/tags/pull-virtiofs-20201026' into staging
virtiofsd pull 2020-10-26
Misono
Set default log level to info
Explicit build option for virtiofsd
Me
xattr name mapping
Stefan
Alternative chroot sandbox method
Max
Submount mechanism
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
# gpg: Signature made Mon 26 Oct 2020 18:41:36 GMT
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert-gitlab/tags/pull-virtiofs-20201026:
tests/acceptance: Add virtiofs_submounts.py
tests/acceptance/boot_linux: Accept SSH pubkey
virtiofsd: Announce sub-mount points
virtiofsd: Store every lo_inode's parent_dev
virtiofsd: Add fuse_reply_attr_with_flags()
virtiofsd: Add attr_flags to fuse_entry_param
virtiofsd: Announce FUSE_ATTR_FLAGS
linux/fuse.h: Pull in from Linux
tools/virtiofsd: xattr name mappings: Simple 'map'
tools/virtiofsd: xattr name mapping examples
tools/virtiofsd: xattr name mappings: Map server xattr names
tools/virtiofsd: xattr name mappings: Map client xattr names
tools/virtiofsd: xattr name mappings: Add option
virtiofsd: add container-friendly -o sandbox=chroot option
virtiofsd: passthrough_ll: set FUSE_LOG_INFO as default log_level
configure: add option for virtiofsd
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The armv7m systick timer is a 24-bit decrementing, wrap-on-zero,
clear-on-write counter. Our current implementation has various
bugs and dubious workarounds in it (for instance see
https://bugs.launchpad.net/qemu/+bug/1872237).
We have an implementation of a simple decrementing counter
and we put a lot of effort into making sure it handles the
interesting corner cases (like "spend a cycle at 0 before
reloading") -- ptimer.
Rewrite the systick timer to use a ptimer rather than
a raw QEMU timer.
Unfortunately this is a migration compatibility break,
which will affect all M-profile boards.
Among other bugs, this fixes
https://bugs.launchpad.net/qemu/+bug/1872237 :
now writes to SYST_CVR when the timer is enabled correctly
do nothing; when the timer is enabled via SYST_CSR.ENABLE,
the ptimer code will (because of POLICY_NO_IMMEDIATE_RELOAD)
arrange that after one timer tick the counter is reloaded
from SYST_RVR and then counts down from there, as the
architecture requires.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201015151829.14656-3-peter.maydell@linaro.org
In ptimer_reload(), we call the callback function provided by the
timer device that is using the ptimer. This callback might disable
the ptimer. The code mostly handles this correctly, except that
we'll still print the warning about "Timer with delta zero,
disabling" if the now-disabled timer happened to be set such that it
would fire again immediately if it were enabled (eg because the
limit/reload value is zero).
Suppress the spurious warning message and the unnecessary
repeat-deletion of the underlying timer in this case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20201015151829.14656-2-peter.maydell@linaro.org
Included the newly implemented SBSA generic watchdog device model into
SBSA platform
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201027015927.29495-3-shashi.mallela@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Generic watchdog device model implementation as per ARM SBSA v6.0
Signed-off-by: Shashi Mallela <shashi.mallela@linaro.org>
Message-id: 20201027015927.29495-2-shashi.mallela@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the 'uart-out' clock from the CPRMAN to the PL011 instance.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a clock input to the PL011 UART so we can compute the current baud
rate and trace it. This is intended for developers who wish to use QEMU
to e.g. debug their firmware or to figure out the baud rate configured
by an unknown/closed source binary.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Those reset values have been extracted from a Raspberry Pi 3 model B
v1.2, using the 2020-08-20 version of raspios. The dump was done using
the debugfs interface of the CPRMAN driver in Linux (under
'/sys/kernel/debug/clk'). Each exposed clock tree stage (PLLs, channels
and muxes) can be observed by reading the 'regdump' file (e.g.
'plla/regdump').
Those values are set by the Raspberry Pi firmware at boot time (Linux
expects them to be set when it boots up).
Some stages are not exposed by the Linux driver (e.g. the PLL B). For
those, the reset values are unknown and left to 0 which implies a
disabled output.
Once booted in QEMU, the final clock tree is very similar to the one
visible on real hardware. The differences come from some unimplemented
devices for which the driver simply disable the corresponding clock.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This simple mux sits between the PLL channels and the DSI0E and DSI0P
clock muxes. This mux selects between PLLA-DSI0 and PLLD-DSI0 channel
and outputs the selected signal to source number 4 of DSI0E/P clock
muxes. It is controlled by the cm_dsi0hsck register.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A clock mux can be configured to select one of its 10 sources through
the CM_CTL register. It also embeds yet another clock divider, composed
of an integer part and a fractional part. The number of bits of each
part is mux dependent.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The clock multiplexers are the last clock stage in the CPRMAN. Each mux
outputs one clock signal that goes out of the CPRMAN to the SoC
peripherals.
Each mux has at most 10 sources. The sources 0 to 3 are common to all
muxes. They are:
0. ground (no clock signal)
1. the main oscillator (xosc)
2. "test debug 0" clock
3. "test debug 1" clock
Test debug 0 and 1 are actual clock muxes that can be used as sources to
other muxes (for debug purpose).
Sources 4 to 9 are mux specific and can be unpopulated (grounded). Those
sources are fed by the PLL channels outputs.
One corner case exists for DSI0E and DSI0P muxes. They have their source
number 4 connected to an intermediate multiplexer that can select
between PLLA-DSI0 and PLLD-DSI0 channel. This multiplexer is called
DSI0HSCK and is not a clock mux as such. It is really a simple mux from
the hardware point of view (see https://elinux.org/The_Undocumented_Pi).
This mux is not implemented in this commit.
Note that there is some muxes for which sources are unknown (because of
a lack of documentation). For those cases all the sources are connected
to ground in this implementation.
Each clock mux output is exported by the CPRMAN at the qdev level,
adding the suffix '-out' to the mux name to form the output clock name.
(E.g. the 'uart' mux sees its output exported as 'uart-out' at the
CPRMAN level.)
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A PLL channel is able to further divide the generated PLL frequency.
The divider is given in the CTRL_A2W register. Some channels have an
additional fixed divider which is always applied to the signal.
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
PLLs are composed of multiple channels. Each channel outputs one clock
signal. They are modeled as one device taking the PLL generated clock as
input, and outputting a new clock.
A channel shares the CM register with its parent PLL, and has its own
A2W_CTRL register. A write to the CM register will trigger an update of
the PLL and all its channels, while a write to an A2W_CTRL channel
register will update the required channel only.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPRMAN PLLs generate a clock based on a prescaler, a multiplier and
a divider. The prescaler doubles the parent (xosc) frequency, then the
multiplier/divider are applied. The multiplier has an integer and a
fractional part.
This commit also implements the CPRMAN CM_LOCK register. This register
reports which PLL is currently locked. We consider a PLL has being
locked as soon as it is enabled (on real hardware, there is a delay
after turning a PLL on, for it to stabilize).
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are 5 PLLs in the CPRMAN, namely PLL A, C, D, H and B. All of them
take the xosc clock as input and produce a new clock.
This commit adds a skeleton implementation for the PLLs as sub-devices
of the CPRMAN. The PLLs are instantiated and connected internally to the
main oscillator.
Each PLL has 6 registers : CM, A2W_CTRL, A2W_ANA[0,1,2,3], A2W_FRAC. A
write to any of them triggers a call to the (not yet implemented)
pll_update function.
If the main oscillator changes frequency, an update is also triggered.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The BCM2835 CPRMAN is the clock manager of the SoC. It is composed of a
main oscillator, and several sub-components (PLLs, multiplexers, ...) to
generate the BCM2835 clock tree.
This commit adds a skeleton of the CPRMAN, with a dummy register
read/write implementation. It embeds the main oscillator (xosc) from
which all the clocks will be derived.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPRMAN (clock controller) was mapped at the watchdog/power manager
address. It was also split into two unimplemented peripherals (CM and
A2W) but this is really the same one, as shown by this extract of the
Raspberry Pi 3 Linux device tree:
watchdog@7e100000 {
compatible = "brcm,bcm2835-pm\0brcm,bcm2835-pm-wdt";
[...]
reg = <0x7e100000 0x114 0x7e00a000 0x24>;
[...]
};
[...]
cprman@7e101000 {
compatible = "brcm,bcm2835-cprman";
[...]
reg = <0x7e101000 0x2000>;
[...]
};
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The nanosecond unit greatly limits the dynamic range we can display in
clock value traces, for values in the order of 1GHz and more. The
internal representation can go way beyond this value and it is quite
common for today's clocks to be within those ranges.
For example, a frequency between 500MHz+ and 1GHz will be displayed as
1ns. Beyond 1GHz, it will show up as 0ns.
Replace nanosecond periods traces with frequencies in the Hz unit
to have more dynamic range in the trace output.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Signed-off-by: Luc Michel <luc@lmichel.fr>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use of 0x%d - make up our mind as 0x%x
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20201014193355.53074-1-dgilbert@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Pi 3A+ is a stripped down version of the 3B:
- 512 MiB of RAM instead of 1 GiB
- no on-board ethernet chipset
Add it as it is a closer match to what we model.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-10-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Similarly to the Pi A, the Pi Zero uses a BCM2835 SoC (ARMv6Z core).
The only difference between the revision 1.2 and 1.3 is the latter
exposes a CSI camera connector. As we do not implement the Unicam
peripheral, there is no point in exposing a camera connector :)
Therefore we choose to model the 1.2 revision.
Example booting the machine using content from [*]:
$ qemu-system-arm -M raspi0 -serial stdio \
-kernel raspberrypi/firmware/boot/kernel.img \
-dtb raspberrypi/firmware/boot/bcm2708-rpi-zero.dtb \
-append 'printk.time=0 earlycon=pl011,0x20201000 console=ttyAMA0'
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.118+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1311 Mon Apr 27 14:16:15 BST 2020
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[ 0.000000] CPU: VIPT aliasing data cache, unknown instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi Zero
...
[*] http://archive.raspberrypi.org/debian/pool/main/r/raspberrypi-firmware/raspberrypi-kernel_1.20200512-2_armhf.deb
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-9-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Pi A is almost the first machine released.
It uses a BCM2835 SoC which includes a ARMv6Z core.
Example booting the machine using content from [*]
(we use the device tree from the B model):
$ qemu-system-arm -M raspi1ap -serial stdio \
-kernel raspberrypi/firmware/boot/kernel.img \
-dtb raspberrypi/firmware/boot/bcm2708-rpi-b-plus.dtb \
-append 'earlycon=pl011,0x20201000 console=ttyAMA0'
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.19.118+ (dom@buildbot) (gcc version 4.9.3 (crosstool-NG crosstool-ng-1.22.0-88-g8460611)) #1311 Mon Apr 27 14:16:15 BST 2020
[ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d
[ 0.000000] CPU: VIPT aliasing data cache, unknown instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi Model B+
...
[*] http://archive.raspberrypi.org/debian/pool/main/r/raspberrypi-firmware/raspberrypi-kernel_1.20200512-2_armhf.deb
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-8-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The realize() function is clearly composed of two parts,
each described by a comment:
void realize()
{
/* common peripherals from bcm2835 */
...
/* bcm2836 interrupt controller (and mailboxes, etc.) */
...
}
Split the two part, so we can reuse the common part with other
SoCs from this family.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It makes no sense to set enabled-cpus=0 on single core SoCs.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The BCM2835 has only one core. Introduce the core_count field to
be able to use values different than BCM283X_NCPUS (4).
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove usage of TypeInfo::class_data. Instead fill the fields in
the corresponding class_init().
So far all children use the same values for almost all fields,
but we are going to add the BCM2711/BCM2838 SoC for the raspi4
machine which use different fields.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
No code out of bcm2836.c uses (or requires) the BCM283XInfo
declarations. Move it locally to the C source file.
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201024170127.3592182-2-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Ensure the vSMMUv3 will be restored before all PCIe devices so that DMA
translation can work properly during migration.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Message-id: 20201019091508.197-1-yuzenghui@huawei.com
Acked-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM7xx chips have multiple GPIO controllers that are mostly
identical except for some minor differences like the reset values of
some registers. Each controller controls up to 32 pins.
Each individual pin is modeled as a pair of unnamed GPIOs -- one for
emitting the actual pin state, and one for driving the pin externally.
Like the nRF51 GPIO controller, a gpio level may be negative, which
means the pin is not driven, or floating.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM730 and NPCM750 chips have a single USB host port shared between
a USB 2.0 EHCI host controller and a USB 1.1 OHCI host controller. This
adds support for both of them.
Testing notes:
* With -device usb-kbd, qemu will automatically insert a full-speed
hub, and the keyboard becomes controlled by the OHCI controller.
* With -device usb-kbd,bus=usb-bus.0,port=1, the keyboard is directly
attached to the port without any hubs, and the device becomes
controlled by the EHCI controller since it's high speed capable.
* With -device usb-kbd,bus=usb-bus.0,port=1,usb_version=1, the
keyboard is directly attached to the port, but it only advertises
itself as full-speed capable, so it becomes controlled by the OHCI
controller.
In all cases, the keyboard device enumerates correctly.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RNG module returns a byte of randomness when the Data Valid bit is
set.
This implementation ignores the prescaler setting, and loads a new value
into RNGD every time RNGCS is read while the RNG is enabled and random
data is available.
A qtest featuring some simple randomness tests is included.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The watchdog is part of NPCM7XX's timer module. Its behavior is
controlled by the WTCR register in the timer.
When enabled, the watchdog issues an interrupt signal after a pre-set
amount of cycles, and issues a reset signal shortly after that.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: deleted blank line at end of npcm_watchdog_timer-test.c]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows us to reuse npcm7xx_timer_pause for the watchdog timer.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch sets min_cpus field for xlnx-versal-virt platform,
because it always creates XLNX_VERSAL_NR_ACPUS cpus even with
-smp 1 command line option.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgalyuk@ispras.ru>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 160343854912.8460.17915238517799132371.stgit@pasha-ThinkPad-X280
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Philippe Mathieu-Daudé
Ben Widawsky
Stefano Garzarella
Si-Wei Liu
Peter Maydell
Alex Williamson
Shashi Mallela
Luc Michel
Dr. David Alan Gilbert
Philippe Mathieu-Daudé
Zenghui Yu
Havard Skinnemoen
Hao Wu
Pavel Dovgalyuk