Secure mode is not exempted from checking SCR_EL3.TLOR, and in the
future HCR_EL2.TLOR when S-EL2 is enabled.
Signed-off-by: Rémi Denis-Courmont <remi.denis.courmont@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
HCR should be applied when NS is set, not when it is cleared.
Signed-off-by: Rémi Denis-Courmont <remi.denis.courmont@huawei.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The helper functions for performing the udot/sdot operations against
a scalar were not using an address-swizzling macro when converting
the index of the scalar element into a pointer into the vm array.
This had no effect on little-endian hosts but meant we generated
incorrect results on big-endian hosts.
For these insns, the index is indexing over group of 4 8-bit values,
so 32 bits per indexed entity, and H4() is therefore what we want.
(For Neon the only possible input indexes are 0 and 1.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201028191712.4910-3-peter.maydell@linaro.org
In the neon_padd/pmax/pmin helpers for float16, a cut-and-paste error
meant we were using the H4() address swizzler macro rather than the
H2() which is required for 2-byte data. This had no effect on
little-endian hosts but meant we put the result data into the
destination Dreg in the wrong order on big-endian hosts.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201028191712.4910-2-peter.maydell@linaro.org
We can use proper widening loads to extend 32-bit inputs,
and skip the "widenfn" step.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-12-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In both cases, we can sink the write-back and perform
the accumulate into the normal destination temps.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-11-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The only uses of this function are for loading VFP
double-precision values, and nothing to do with NEON.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-10-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace all uses of neon_load/store_reg64 within translate-neon.c.inc.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-9-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The only uses of this function are for loading VFP
single-precision values, and nothing to do with NEON.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-8-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can then use this to improve VMOV (scalar to gp) and
VMOV (gp to scalar) so that we simply perform the memory
operation that we wanted, rather than inserting or
extracting from a 32-bit quantity.
These were the last uses of neon_load/store_reg, so remove them.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-7-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Model these off the aa64 read/write_vec_element functions.
Use it within translate-neon.c.inc. The new functions do
not allocate or free temps, so this rearranges the calling
code a bit.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-6-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This seems a bit more readable than using offsetof CPU_DoubleU.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-5-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are the only users of neon_reg_offset, so remove that.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-4-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will shortly have users outside of translate-neon.c.inc.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This function makes it clear that we're talking about the whole
register, and not the 32-bit piece at index 0. This fixes a bug
when running on a big-endian host.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201030022618.785675-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Here's the next pull request for ppc and spapr related patches, which
should be the last things for soft freeze. Includes:
* Numerous error handling cleanups from Greg Kurz
* Cleanups to cpu realization and hotplug handling from Greg Kurz
* A handful of other small fixes and cleanups
This does include a change to pc_dimm_plug() that isn't in my normal
areas of concern. That's there as a a prerequisite for ppc specific
changes, and has an ack from Igor.
-----BEGIN PGP SIGNATURE-----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=igPS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-5.2-20201028' into staging
ppc patch queue 2020-10-28
Here's the next pull request for ppc and spapr related patches, which
should be the last things for soft freeze. Includes:
* Numerous error handling cleanups from Greg Kurz
* Cleanups to cpu realization and hotplug handling from Greg Kurz
* A handful of other small fixes and cleanups
This does include a change to pc_dimm_plug() that isn't in my normal
areas of concern. That's there as a a prerequisite for ppc specific
changes, and has an ack from Igor.
# gpg: Signature made Tue 27 Oct 2020 14:13:21 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-5.2-20201028:
ppc/: fix some comment spelling errors
spapr: Improve spapr_reallocate_hpt() error reporting
target/ppc: Fix kvmppc_load_htab_chunk() error reporting
spapr: Use error_append_hint() in spapr_reallocate_hpt()
spapr: Simplify error handling in spapr_memory_plug()
spapr: Pass &error_abort when getting some PC DIMM properties
spapr: Use appropriate getter for PC_DIMM_SLOT_PROP
spapr: Use appropriate getter for PC_DIMM_ADDR_PROP
pc-dimm: Drop @errp argument of pc_dimm_plug()
spapr: Simplify spapr_cpu_core_realize() and spapr_cpu_core_unrealize()
spapr: Make spapr_cpu_core_unrealize() idempotent
spapr: Drop spapr_delete_vcpu() unused argument
spapr: Unrealize vCPUs with qdev_unrealize()
spapr: Fix leak of CPU machine specific data
spapr: Move spapr_create_nvdimm_dr_connectors() to core machine code
hw/net: move allocation to the heap due to very large stack frame
ppc/spapr: re-assert IRQs during event-scan if there are pending
spapr: Clarify why DR connectors aren't user creatable
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I found that there are many spelling errors in the comments of qemu/target/ppc.
I used spellcheck to check the spelling errors and found some errors in the folder.
Signed-off-by: zhaolichang <zhaolichang@huawei.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Message-Id: <20201009064449.2336-3-zhaolichang@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
If kvmppc_load_htab_chunk() fails, its return value is propagated up
to vmstate_load(). It should thus be a negative errno, not -1 (which
maps to EPERM and would lure the user into thinking that the problem
is necessarily related to a lack of privilege).
Return the error reported by KVM or ENOSPC in case of short write.
While here, propagate the error message through an @errp argument
and have the caller to print it with error_report_err() instead
of relying on fprintf().
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160371604713.305923.5264900354159029580.stgit@bahia.lan>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since we introduced CPU hot-unplug in sPAPR, we don't unrealize the
vCPU objects explicitly. Instead, we let QOM handle that for us under
object_property_del_all() when the CPU core object is finalized. The
only thing we do is calling cpu_remove_sync() to tear the vCPU thread
down.
This happens to work but it is ugly because:
- we call qdev_realize() but the corresponding qdev_unrealize() is
buried deep in the QOM code
- we call cpu_remove_sync() to undo qemu_init_vcpu() called by
ppc_cpu_realize() in target/ppc/translate_init.c.inc
- the CPU init and teardown paths aren't really symmetrical
The latter didn't bite us so far but a future patch that greatly
simplifies the CPU core realize path needs it to avoid a crash
in QOM.
For all these reasons, have ppc_cpu_unrealize() to undo the changes
of ppc_cpu_realize() by calling cpu_remove_sync() at the right place,
and have the sPAPR CPU core code to call qdev_unrealize().
This requires to add a missing stub because translate_init.c.inc is
also compiled for user mode.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <160279671236.1808373.14732005038172874990.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Transform the prot bit to a qemu internal page bit, and save
it in the page tables.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201023123840.19988-1-chetan4windows@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There are many spelling errors in the comments of target/rx.
Use spellcheck to check the spelling errors, then fix them.
Signed-off-by: zhaolichang <zhaolichang@huawei.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Philippe Mathieu-Daude<f4bug@amsat.org>
Message-Id: <20201009064449.2336-5-zhaolichang@huawei.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There are many spelling errors in the comments of target/sh4.
Use spellcheck to check the spelling errors, then fix them.
Signed-off-by: zhaolichang <zhaolichang@huawei.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Philippe Mathieu-Daude<f4bug@amsat.org>
Message-Id: <20201009064449.2336-10-zhaolichang@huawei.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Linux userspace always sees coprocessors as enabled. CPENABLE register
and coprocessor exceptions are used internally by the kernel to manage
lazy coprocessor context switch. None of it is needed for linux-user.
Always enable all coprocessors for user emulation.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20200829104758.22337-1-jcmvbkbc@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
VS-stage translation at get_physical_address needs to translate pte
address by G-stage translation. But the G-stage translation error
can not be distinguished from VS-stage translation error in
riscv_cpu_tlb_fill. On migration, destination needs to rebuild pte,
and this G-stage translation error must be handled by HS-mode. So
introduce TRANSLATE_STAGE2_FAIL so that riscv_cpu_tlb_fill could
distinguish and raise it to HS-mode.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Yipeng Yin <yinyipeng1@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201014101728.848-1-jiangyifei@huawei.com
[ Change by AF:
- Clarify the fault_pte_addr shift
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The HLVX.WU instruction is supposed to read a machine word,
but prior to this change it read a byte instead.
Fixes: 8c5362acb5 ("target/riscv: Allow generating hlv/hlvx/hsv instructions")
Signed-off-by: Georg Kotheimer <georg.kotheimer@kernkonzept.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201013172223.443645-1-georg.kotheimer@kernkonzept.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The hstatus.GVA bit was not set if the faulting guest virtual address
was zero.
Signed-off-by: Georg Kotheimer <georg.kotheimer@kernkonzept.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201013173054.451135-1-georg.kotheimer@kernkonzept.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When trapping from virt into HS mode, hstatus.SPVP was set to
the value of sstatus.SPP, as according to the specification both
flags should be set to the same value.
However, the assignment of SPVP takes place before SPP itself is
updated, which results in SPVP having an outdated value.
Signed-off-by: Georg Kotheimer <georg.kotheimer@kernkonzept.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201013151054.396481-1-georg.kotheimer@kernkonzept.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently we log interrupts and exceptions using the trace backend in
riscv_cpu_do_interrupt(). We also log exceptions using the interrupt log
mask (-d int) in riscv_raise_exception().
This patch converts riscv_cpu_do_interrupt() to log both interrupts and
exceptions with the interrupt log mask, so that both are printed when a
user runs QEMU with -d int.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 29a8c766c7c4748d0f2711c3a0abb81208138c5e.1601652179.git.alistair.francis@wdc.com
Diag318 fencing needs to be determined on the current VM PV state and
not on the state that the VM has when we create the CPU model.
Fixes: fabdada935 ("s390: guest support for diagnose 0x318")
Reported-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Tested-by: Marc Hartmayer <mhartmay@linux.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Collin Walling <walling@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Message-Id: <20201022103135.126033-3-frankja@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
If the M-profile low-overhead-branch extension is implemented, FPSCR
bits [18:16] are a new field LTPSIZE. If MVE is not implemented
(currently always true for us) then this field always reads as 4 and
ignores writes.
These bits used to be the vector-length field for the old
short-vector extension, so we need to take care that they are not
misinterpreted as setting vec_len. We do this with a rearrangement
of the vfp_set_fpscr() code that deals with vec_len, vec_stride
and also the QC bit; this obviates the need for the M-profile
only masking step that we used to have at the start of the function.
We provide a new field in CPUState for LTPSIZE, even though this
will always be 4, in preparation for MVE, so we don't have to
come back later and split it out of the vfp.xregs[FPSCR] value.
(This state struct field will be saved and restored as part of
the FPSCR value via the vmstate_fpscr in machine.c.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-11-peter.maydell@linaro.org
M-profile CPUs with half-precision floating point support should
be able to write to FPSCR.FZ16, but an M-profile specific masking
of the value at the top of vfp_set_fpscr() currently prevents that.
This is not yet an active bug because we have no M-profile
FP16 CPUs, but needs to be fixed before we can add any.
The bits that the masking is effectively preventing from being
set are the A-profile only short-vector Len and Stride fields,
plus the Neon QC bit. Rearrange the order of the function so
that those fields are handled earlier and only under a suitable
guard; this allows us to drop the M-profile specific masking,
making FZ16 writeable.
This change also makes the QC bit correctly RAZ/WI for older
no-Neon A-profile cores.
This refactoring also paves the way for the low-overhead-branch
LTPSIZE field, which uses some of the bits that are used for
A-profile Stride and Len.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-10-peter.maydell@linaro.org
In arm_cpu_realizefn(), if the CPU has VFP or Neon disabled then we
squash the ID register fields so that we don't advertise it to the
guest. This code was written for A-profile and needs some tweaks to
work correctly on M-profile:
* A-profile only fields should not be zeroed on M-profile:
- MVFR0.FPSHVEC,FPTRAP
- MVFR1.SIMDLS,SIMDINT,SIMDSP,SIMDHP
- MVFR2.SIMDMISC
* M-profile only fields should be zeroed on M-profile:
- MVFR1.FP16
In particular, because MVFR1.SIMDHP on A-profile is the same field as
MVFR1.FP16 on M-profile this code was incorrectly disabling FP16
support on an M-profile CPU (where has_neon is always false). This
isn't a visible bug yet because we don't have any M-profile CPUs with
FP16 support, but the change is necessary before we introduce any.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-9-peter.maydell@linaro.org
v8.1M's "low-overhead-loop" extension has three instructions
for looping:
* DLS (start of a do-loop)
* WLS (start of a while-loop)
* LE (end of a loop)
The loop-start instructions are both simple operations to start a
loop whose iteration count (if any) is in LR. The loop-end
instruction handles "decrement iteration count and jump back to loop
start"; it also caches the information about the branch back to the
start of the loop to improve performance of the branch on subsequent
iterations.
As with the branch-future instructions, the architecture permits an
implementation to discard the LO_BRANCH_INFO cache at any time, and
QEMU takes the IMPDEF option to never set it in the first place
(equivalent to discarding it immediately), because for us a "real"
implementation would be unnecessary complexity.
(This implementation only provides the simple looping constructs; the
vector extension MVE (Helium) adds some extra variants to handle
looping across vectors. We'll add those later when we implement
MVE.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-8-peter.maydell@linaro.org
v8.1M implements a new 'branch future' feature, which is a
set of instructions that request the CPU to perform a branch
"in the future", when it reaches a particular execution address.
In hardware, the expected implementation is that the information
about the branch location and destination is cached and then
acted upon when execution reaches the specified address.
However the architecture permits an implementation to discard
this cached information at any point, and so guest code must
always include a normal branch insn at the branch point as
a fallback. In particular, an implementation is specifically
permitted to treat all BF insns as NOPs (which is equivalent
to discarding the cached information immediately).
For QEMU, implementing this caching of branch information
would be complicated and would not improve the speed of
execution at all, so we make the IMPDEF choice to implement
all BF insns as NOPs.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-7-peter.maydell@linaro.org
The BLX immediate insn in the Thumb encoding always performs
a switch from Thumb to Arm state. This would be totally useless
in M-profile which has no Arm decoder, and so the instruction
does not exist at all there. Make the encoding UNDEF for M-profile.
(This part of the encoding space is used for the branch-future
and low-overhead-loop insns in v8.1M.)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-6-peter.maydell@linaro.org
The t32 decode has a group which represents a set of insns
which overlap with B_cond_thumb because they have [25:23]=111
(which is an invalid condition code field for the branch insn).
This group is currently defined using the {} overlap-OK syntax,
but it is almost entirely non-overlapping patterns. Switch
it over to use a non-overlapping group.
For this to be valid syntactically, CPS must move into the same
overlapping-group as the hint insns (CPS vs hints was the
only actual use of the overlap facility for the group).
The non-overlapping subgroup for CLREX/DSB/DMB/ISB/SB is no longer
necessary and so we can remove it (promoting those insns to
be members of the parent group).
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20201019151301.2046-5-peter.maydell@linaro.org
From v8.1M, disabled-coprocessor handling changes slightly:
* coprocessors 8, 9, 14 and 15 are also governed by the
cp10 enable bit, like cp11
* an extra range of instruction patterns is considered
to be inside the coprocessor space
We previously marked these up with TODO comments; implement the
correct behaviour.
Unfortunately there is no ID register field which indicates this
behaviour. We could in theory test an unrelated ID register which
indicates guaranteed-to-be-in-v8.1M behaviour like ID_ISAR0.CmpBranch
>= 3 (low-overhead-loops), but it seems better to simply define a new
ARM_FEATURE_V8_1M feature flag and use it for this and other
new-in-v8.1M behaviour that isn't identifiable from the ID registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201019151301.2046-3-peter.maydell@linaro.org
Unlike many other bits in HCR_EL2, the description for this
bit does not contain the phrase "if ... this field behaves
as 0 for all purposes other than", so do not squash the bit
in arm_hcr_el2_eff.
Instead, replicate the E2H+TGE test in the two places that
require it.
Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Message-id: 20201008162155.161886-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The reporting in AArch64.TagCheckFail only depends on PSTATE.EL,
and not the AccType of the operation. There are two guest
visible problems that affect LDTR and STTR because of this:
(1) Selecting TCF0 vs TCF1 to decide on reporting,
(2) Report "data abort same el" not "data abort lower el".
Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Message-id: 20201008162155.161886-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We already have the full ARMMMUIdx as computed from the
function parameter.
For the purpose of regime_has_2_ranges, we can ignore any
difference between AccType_Normal and AccType_Unpriv, which
would be the only difference between the passed mmu_idx
and arm_mmu_idx_el.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Message-id: 20201008162155.161886-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When TBI is enabled in a given regime, 56 bits of the address
are significant and we need to clear out any other matching
virtual addresses with differing tags.
The other uses of tlb_flush_page (without mmuidx) in this file
are only used by aarch32 mode.
Fixes: 38d931687f
Reported-by: Jordan Frank <jordanfrank@fb.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20201016210754.818257-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For AArch32, unlike the VCVT of integer to float, which honours the
rounding mode specified by the FPSCR, VCVT of fixed-point to float is
always round-to-nearest. (AArch64 fixed-point-to-float conversions
always honour the FPCR rounding mode.)
Implement this by providing _round_to_nearest versions of the
relevant helpers which set the rounding mode temporarily when making
the call to the underlying softfloat function.
We only need to change the VFP VCVT instructions, because the
standard- FPSCR value used by the Neon VCVT is always set to
round-to-nearest, so we don't need to do the extra work of saving
and restoring the rounding mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201013103532.13391-1-peter.maydell@linaro.org
The SMLAD instruction is supposed to:
* signed multiply Rn[15:0] * Rm[15:0]
* signed multiply Rn[31:16] * Rm[31:16]
* perform a signed addition of the products and Ra
* set Rd to the low 32 bits of the theoretical
infinite-precision result
* set the Q flag if the sign-extension of Rd
would differ from the infinite-precision result
(ie on overflow)
Our current implementation doesn't quite do this, though: it performs
an addition of the products setting Q on overflow, and then it adds
Ra, again possibly setting Q. This sometimes incorrectly sets Q when
the architecturally mandated only-check-for-overflow-once algorithm
does not. For instance:
r1 = 0x80008000; r2 = 0x80008000; r3 = 0xffffffff
smlad r0, r1, r2, r3
This is (-32768 * -32768) + (-32768 * -32768) - 1
The products are both 0x4000_0000, so when added together as 32-bit
signed numbers they overflow (and QEMU sets Q), but because the
addition of Ra == -1 brings the total back down to 0x7fff_ffff
there is no overflow for the complete operation and setting Q is
incorrect.
Fix this edge case by resorting to 64-bit arithmetic for the
case where we need to add three values together.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201009144712.11187-1-peter.maydell@linaro.org
. Fix some comment spelling errors
. Demacro some TCG helpers
. Add loongson-ext lswc2/lsdc2 group of instructions
. Log unimplemented cache opcode
. Increase number of TLB entries on the 34Kf core
. Allow the CPU to use dynamic frequencies
. Calculate the CP0 timer period using the CPU frequency
. Set CPU frequency for each machine
. Fix Malta FPGA I/O region size
. Allow running qtests when ROM is missing
. Add record/replay acceptance tests
. Update MIPS CPU documentation
. MAINTAINERS updates
CI jobs results:
https://gitlab.com/philmd/qemu/-/pipelines/203931842https://travis-ci.org/github/philmd/qemu/builds/736491461https://cirrus-ci.com/build/6272264062631936https://app.shippable.com/github/philmd/qemu/runs/886/summary/console
-----BEGIN PGP SIGNATURE-----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=BOxw
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd-gitlab/tags/mips-next-20201017' into staging
MIPS patches queue
. Fix some comment spelling errors
. Demacro some TCG helpers
. Add loongson-ext lswc2/lsdc2 group of instructions
. Log unimplemented cache opcode
. Increase number of TLB entries on the 34Kf core
. Allow the CPU to use dynamic frequencies
. Calculate the CP0 timer period using the CPU frequency
. Set CPU frequency for each machine
. Fix Malta FPGA I/O region size
. Allow running qtests when ROM is missing
. Add record/replay acceptance tests
. Update MIPS CPU documentation
. MAINTAINERS updates
CI jobs results:
https://gitlab.com/philmd/qemu/-/pipelines/203931842https://travis-ci.org/github/philmd/qemu/builds/736491461https://cirrus-ci.com/build/6272264062631936https://app.shippable.com/github/philmd/qemu/runs/886/summary/console
# gpg: Signature made Sat 17 Oct 2020 14:59:53 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/mips-next-20201017: (44 commits)
target/mips: Increase number of TLB entries on the 34Kf core (16 -> 64)
MAINTAINERS: Remove duplicated Malta test entries
MAINTAINERS: Downgrade MIPS Boston to 'Odd Fixes', fix Paul Burton mail
MAINTAINERS: Put myself forward for MIPS target
MAINTAINERS: Remove myself
docs/system: Update MIPS CPU documentation
tests/acceptance: Add MIPS record/replay tests
hw/mips: Remove exit(1) in case of missing ROM
hw/mips: Rename TYPE_MIPS_BOSTON to TYPE_BOSTON
hw/mips: Simplify code using ROUND_UP(INITRD_PAGE_SIZE)
hw/mips: Simplify loading 64-bit ELF kernels
hw/mips/malta: Use clearer qdev style
hw/mips/malta: Move gt64120 related code together
hw/mips/malta: Fix FPGA I/O region size
target/mips/cpu: Display warning when CPU is used without input clock
hw/mips/cps: Do not allow use without input clock
hw/mips/malta: Set CPU frequency to 320 MHz
hw/mips/boston: Set CPU frequency to 1 GHz
hw/mips/cps: Expose input clock and connect it to CPU cores
hw/mips/jazz: Correct CPU frequencies
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
during my split of cpus.c, code line
"current_cpu = cpu"
was removed by mistake, causing hax to break.
This commit fixes the situation restoring it.
Reported-by: Volker Rümelin <vr_qemu@t-online.de>
Fixes: e92558e4bf
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20201016080032.13914-1-cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Per "MIPS32 34K Processor Core Family Software User's Manual,
Revision 01.13" page 8 in "Joint TLB (JTLB)" section:
"The JTLB is a fully associative TLB cache containing 16, 32,
or 64-dual-entries mapping up to 128 virtual pages to their
corresponding physical addresses."
There is no particular reason to restrict the 34Kf core model to
16 TLB entries, so raise its config to 64.
This is helpful for other projects, in particular the Yocto Project:
Yocto Project uses qemu-system-mips 34Kf cpu model, to run 32bit
MIPS CI loop. It was observed that in this case CI test execution
time was almost twice longer than 64bit MIPS variant that runs
under MIPS64R2-generic model. It was investigated and concluded
that the difference in number of TLBs 16 in 34Kf case vs 64 in
MIPS64R2-generic is responsible for most of CI real time execution
difference. Because with 16 TLBs linux user-land trashes TLB more
and it needs to execute more instructions in TLB refill handler
calls, as result it runs much longer.
(https://lists.gnu.org/archive/html/qemu-devel/2020-10/msg03428.html)
Buglink: https://bugzilla.yoctoproject.org/show_bug.cgi?id=13992
Reported-by: Victor Kamensky <kamensky@cisco.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20201016133317.553068-1-f4bug@amsat.org>
All our QOM users provides an input clock. In order to avoid
avoid future machines added without clock, display a warning.
User-mode emulation use the CP0 timer with the RDHWR instruction
(see commit cdfcad7883) so keep using the fixed 200 MHz clock
without diplaying any warning. Only display it in system-mode
emulation.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012095804.3335117-22-f4bug@amsat.org>
Introduce an helper to create a MIPS CPU and connect it to
a reference clock. This helper is not MIPS specific, but so
far only MIPS CPUs need it.
Suggested-by: Huacai Chen <zltjiangshi@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012095804.3335117-13-f4bug@amsat.org>
Use the Clock API and let the CPU object have an input clock.
If no clock is connected, keep using the default frequency of
200 MHz used since the introduction of the 'r4k' machine in
commit 6af0bf9c7c.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012095804.3335117-12-f4bug@amsat.org>
Since not all CPU implementations use a cores use a CP0 timer
at half the frequency of the CPU, make this variable a property.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012095804.3335117-11-f4bug@amsat.org>
The CP0 timer period is a function of the CPU frequency.
Start using the default values, which will be replaced by
properties in the next commits.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20201012095804.3335117-10-f4bug@amsat.org>
Currently the CP0 timer period is fixed at 10 ns, corresponding
to a fixed CPU frequency of 200 MHz (using half the speed of the
CPU).
In few commits we will be able to use a different CPU frequency.
In preparation, move the cp0_count_ns variable to CPUMIPSState
so we can modify it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20201012095804.3335117-9-f4bug@amsat.org>
TIMER_PERIOD value of '10 ns' can be explained looking at
commit 6af0bf9c7c3doc, where the CPU frequency is 200 MHz
and CP0 default count rate is half the frequency of the
CPU. Document that.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012095804.3335117-8-f4bug@amsat.org>
Name variables holding nanoseconds with the '_ns' suffix.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Message-Id: <20201012095804.3335117-7-f4bug@amsat.org>
The get_random() helper uses the CP0_Wired register, which is
unrelated to the CP0_Count register used as timer.
Commit e16fe40c87 ("Move the MIPS CPU timer in a separate file")
incorrectly moved this get_random() helper with timer specific
code. Move it back to generic CP0 helpers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-Id: <20201012095804.3335117-6-f4bug@amsat.org>
In case the guest uses a cache opcode we are not expecting,
log it to give us a chance to notice it, in case we should
actually do something.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20200813181527.22551-4-f4bug@amsat.org>
QEMU does not model caches, so there is not much to do with the
Invalidate/Writeback opcodes. Make it explicit adding a comment.
Suggested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20200813181527.22551-3-f4bug@amsat.org>
The cache operation is encoded in bits [20:18] of the instruction.
The 'op' argument of helper_cache() contains the bits [20:16].
Extract the 3 bits and parse them using a switch case. This allow
us to handle multiple cache types (the cache type is encoded in
bits [17:16]).
Previously the if() block was only checking the D-Cache (Primary
Data or Unified Primary). Now we also handle the I-Cache (Primary
Instruction), S-Cache (Secondary) and T-Cache (Terciary).
Reported-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Message-Id: <20200813181527.22551-2-f4bug@amsat.org>
LDC2/SDC2 opcodes have been rewritten as "load & store with offset"
group of instructions by loongson-ext ASE.
This patch add implementation of these instructions:
gslbx: load 1 bytes to GPR
gslhx: load 2 bytes to GPR
gslwx: load 4 bytes to GPR
gsldx: load 8 bytes to GPR
gslwxc1: load 4 bytes to FPR
gsldxc1: load 8 bytes to FPR
gssbx: store 1 bytes from GPR
gsshx: store 2 bytes from GPR
gsswx: store 4 bytes from GPR
gssdx: store 8 bytes from GPR
gsswxc1: store 4 bytes from FPR
gssdxc1: store 8 bytes from FPR
Details of Loongson-EXT is here:
https://github.com/FlyGoat/loongson-insn/blob/master/loongson-ext.md
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1602831120-3377-5-git-send-email-chenhc@lemote.com>
LWC2 & SWC2 have been rewritten by Loongson EXT vendor ASE
as "load/store quad word" and "shifted load/store" groups of
instructions.
This patch add implementation of these instructions:
gslwlc1: similar to lwl but RT is FPR instead of GPR
gslwrc1: similar to lwr but RT is FPR instead of GPR
gsldlc1: similar to ldl but RT is FPR instead of GPR
gsldrc1: similar to ldr but RT is FPR instead of GPR
gsswlc1: similar to swl but RT is FPR instead of GPR
gsswrc1: similar to swr but RT is FPR instead of GPR
gssdlc1: similar to sdl but RT is FPR instead of GPR
gssdrc1: similar to sdr but RT is FPR instead of GPR
Details of Loongson-EXT is here:
https://github.com/FlyGoat/loongson-insn/blob/master/loongson-ext.md
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Message-Id: <1602831120-3377-4-git-send-email-chenhc@lemote.com>
[PMD: Reuse t1 on MIPS32, reintroduce t2/fp0]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
LWC2 & SWC2 have been rewritten by Loongson EXT vendor ASE
as "load/store quad word" and "shifted load/store" groups of
instructions.
This patch add implementation of these instructions:
gslq: load 16 bytes to GPR
gssq: store 16 bytes from GPR
gslqc1: load 16 bytes to FPR
gssqc1: store 16 bytes from FPR
Details of Loongson-EXT is here:
https://github.com/FlyGoat/loongson-insn/blob/master/loongson-ext.md
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Message-Id: <1602831120-3377-3-git-send-email-chenhc@lemote.com>
[PMD: Restrict t1 variable to TARGET_MIPS64, remove unused t2/fp0]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove function definitions via macros to achieve better code clarity.
Signed-off-by: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1602103041-32017-4-git-send-email-aleksandar.qemu.devel@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove function definitions via macros to achieve better code clarity.
Signed-off-by: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1602103041-32017-3-git-send-email-aleksandar.qemu.devel@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Remove function definitions via macros to achieve better code clarity.
Signed-off-by: Aleksandar Markovic <aleksandar.qemu.devel@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1602103041-32017-2-git-send-email-aleksandar.qemu.devel@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
There are many spelling errors in the comments in target/mips/.
Use spellcheck to check the spelling errors.
Signed-off-by: zhaolichang <zhaolichang@huawei.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201009064449.2336-7-zhaolichang@huawei.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Icelake-Client CPU models will be removed in the future.
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1600758855-80046-2-git-send-email-robert.hu@linux.intel.com>
[ehabkost: reword deprecation note, fix version in doc]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Implement the ability of marking some versions deprecated. When
that CPU model is chosen, print a warning. The warning message
can be customized, e.g. suggesting an alternative CPU model to be
used instead.
The deprecation message will be printed by x86_cpu_list_entry(),
e.g. '-cpu help'.
QMP command 'query-cpu-definitions' will return a bool value
indicating the deprecation status.
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1600758855-80046-1-git-send-email-robert.hu@linux.intel.com>
[ehabkost: reword commit message]
[ehabkost: Handle NULL cpu_type]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
As IRQ routing is always available on x86,
kvm_allows_irq0_override() will always return true, so we don't
need the function anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200922201922.2153598-4-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
KVM_CAP_IRQ_ROUTING is always available on x86, so replace checks
for kvm_has_gsi_routing() and KVM_CAP_IRQ_ROUTING with asserts.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200922201922.2153598-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
KVM_CAP_IRQ_ROUTING is available since 2009 (Linux v2.6.30), so
it's safe to just make it a requirement on x86.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200922201922.2153598-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
With x2apic enabled, configurations can have more that 255 cores.
Noticed the device add test is hitting an assert when during cpu
hotplug with core_id > 255. This is due to assert check in the
CPUID 0x8000001E.
Remove the assert check and fix the problem.
Fixes the bug:
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1834200
Signed-off-by: Babu Moger <babu.moger@amd.com>
Message-Id: <160072824160.9666.8890355282135970684.stgit@naples-babu.amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Fix typo to use correct edx value for FEATURE_HYPERV_EDX when
hyperv_passthrough is enabled.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Message-Id: <20190820103030.12515-1-zhenyuw@linux.intel.com>
Fixes: e48ddcc6ce ("i386/kvm: implement 'hv-passthrough' mode")
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We only use x86_cpu_get_supported_feature_word() after its implementation,
no forward declaration needed.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200904145431.196885-3-vkuznets@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200921221045.699690-14-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Commit 0b09be2b2f ("Nicer debug output for exceptions") added
twice the same "Tag Overflow" entry, remove the extra one.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <20201011200112.3222822-1-f4bug@amsat.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Missed in commit 41fba1618b "docs/system: convert the documentation of
deprecated features to rST."
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200929075824.1517969-3-armbru@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
VMState handlers are supposed to return negative errno values on failure.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200914123505.612812-4-groug@kaod.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As recommended in "qapi/error.h", indicate success / failure with a
return value. Since ppc_set_compat() is called from a VMState handler,
let's make it an int so that it propagates any negative errno returned
by kvmppc_set_compat(). Do the same for ppc_set_compat_all() for
consistency, even if it isn't called in a context where a negative errno
is required on failure.
This will allow to simplify error handling in the callers.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200914123505.612812-3-groug@kaod.org>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
QEMU supports a 48-bit physical address range, but we don't currently
expose it in the '-cpu max' ID registers (you get the same range as
Cortex-A57, which is 44 bits).
Set the ID_AA64MMFR0.PARange field to indicate 48 bits.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201001160116.18095-1-peter.maydell@linaro.org
We add the kvm-steal-time CPU property and implement it for machvirt.
A tiny bit of refactoring was also done to allow pmu and pvtime to
use the same vcpu device helper functions.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20201001061718.101915-7-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When we compile without KVM support !defined(CONFIG_KVM) we generate
stubs for functions that the linker will still encounter. Sometimes
these stubs can be executed safely and are placed in paths where they
get executed with or without KVM. Other functions should never be
called without KVM. Those functions should be guarded by kvm_enabled(),
but should also be robust to refactoring mistakes. Putting a
g_assert_not_reached() in the function should help. Additionally,
the g_assert_not_reached() calls may actually help the linker remove
some code.
We remove the stubs for kvm_arm_get/put_virtual_time(), as they aren't
necessary at all - the only caller is in kvm.c
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20201001061718.101915-3-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
kvm: uses the generic handler
qtest: uses the generic handler
whpx: changed to use the generic handler (identical implementation)
hax: changed to use the generic handler (identical implementation)
hvf: changed to use the generic handler (identical implementation)
tcg: adapt tcg-cpus to point to the tcg-specific handler
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
register a "CpusAccel" interface for HVF as well.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Roman Bolshakov <r.bolshakov@yadro.com>
[added const]
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
register a "CpusAccel" interface for WHPX as well.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
register a "CpusAccel" interface for HAX as well.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
refactoring of cpus.c continues with cpu timer state extraction.
cpu-timers: responsible for the softmmu cpu timers state,
including cpu clocks and ticks.
icount: counts the TCG instructions executed. As such it is specific to
the TCG accelerator. Therefore, it is built only under CONFIG_TCG.
One complication is due to qtest, which uses an icount field to warp time
as part of qtest (qtest_clock_warp).
In order to solve this problem, provide a separate counter for qtest.
This requires fixing assumptions scattered in the code that
qtest_enabled() implies icount_enabled(), checking each specific case.
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[remove redundant initialization with qemu_spice_init]
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
[fix lingering calls to icount_get]
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rémi Denis-Courmont
Peter Maydell
Richard Henderson
zhaolichang
Greg Kurz
Chetan Pant
Philippe Mathieu-Daudé
Max Filippov
Yifei Jiang
Georg Kotheimer
Alistair Francis
Janosch Frank
Claudio Fontana
Jiaxun Yang
Aleksandar Markovic
Robert Hoo
Eduardo Habkost
Babu Moger
Zhenyu Wang
Vitaly Kuznetsov
Markus Armbruster
Andrew Jones