pconfig feature was added in 5131dc433d and removed in 712f807e19.
This patch mark this feature as known to QEMU and removed by
intentinally. This follows the convention of 9ccb9784b5 and f1a23522b0
dealing with 'osxsave' and 'ospke'.
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190719111222.14943-1-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Do not allocate env->nested_state unless we later need to migrate the
nested virtualization state.
With this change, nested_state_needed() will return false if the
VMX flag is not included in the virtual machine. KVM_GET/SET_NESTED_STATE
is also disabled for SVM which is safer (we know that at least the NPT
root and paging mode have to be saved/loaded), and thus the corresponding
subsection can go away as well.
Inspired by a patch from Liran Alon.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Previous to this change, a vCPU exposed with VMX running on a kernel
without KVM_CAP_NESTED_STATE or KVM_CAP_EXCEPTION_PAYLOAD resulted in
adding a migration blocker. This was because when the code was written
it was thought there is no way to reliably know if a vCPU is utilising
VMX or not at runtime. However, it turns out that this can be known to
some extent:
In order for a vCPU to enter VMX operation it must have CR4.VMXE set.
Since it was set, CR4.VMXE must remain set as long as the vCPU is in
VMX operation. This is because CR4.VMXE is one of the bits set
in MSR_IA32_VMX_CR4_FIXED1.
There is one exception to the above statement when vCPU enters SMM mode.
When a vCPU enters SMM mode, it temporarily exits VMX operation and
may also reset CR4.VMXE during execution in SMM mode.
When the vCPU exits SMM mode, vCPU state is restored to be in VMX operation
and CR4.VMXE is restored to its original state of being set.
Therefore, when the vCPU is not in SMM mode, we can infer whether
VMX is being used by examining CR4.VMXE. Otherwise, we cannot
know for certain but assume the worse that vCPU may utilise VMX.
Summaring all the above, a vCPU may have enabled VMX in case
CR4.VMXE is set or vCPU is in SMM mode.
Therefore, remove migration blocker and check before migration
(cpu_pre_save()) if the vCPU may have enabled VMX. If true, only then
require relevant kernel capabilities.
While at it, demand KVM_CAP_EXCEPTION_PAYLOAD only when the vCPU is in
guest-mode and there is a pending/injected exception. Otherwise, this
kernel capability is not required for proper migration.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Maran Wilson <maran.wilson@oracle.com>
Tested-by: Maran Wilson <maran.wilson@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The commit referenced below skipped pinning ram device memory when
ram blocks are added, we need to do the same when they're removed.
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Fixes: cedc0ad539 ("target/i386: sev: Do not pin the ram device memory region")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Message-Id: <156320087103.2556.10983987500488190423.stgit@gimli.home>
Reviewed-by: Singh, Brijesh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJdH7FgAAoJEL/70l94x66DdUUH+gLr/ZdjLIdfYy9cjcnevf4E
cJlxdaW9KvUsK2uVgqQ/3b1yF+GCGk10n6n8ZTIbClhs+6NpqEMz5O3FA/Na6FGA
48M2DwJaJ2H9AG/lQBlSBNUZfLsEJ9rWy7DHvNut5XMJFuWGwdtF/jRhUm3KqaRq
vAaOgcQHbzHU9W8r1NJ7l6pnPebeO7S0JQV+82T/ITTz2gEBDUkJ36boO6fedkVQ
jLb9nZyG3CJXHm2WlxGO4hkqbLFzURnCi6imOh2rMdD8BCu1eIVl59tD1lC/A0xv
Pp3xXnv9SgJXsV4/I/N3/nU85ZhGVMPQZXkxaajHPtJJ0rQq7FAG8PJMEj9yPe8=
=poke
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
Bugfixes.
# gpg: Signature made Fri 05 Jul 2019 21:21:52 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream:
ioapic: use irq number instead of vector in ioapic_eoi_broadcast
hw/i386: Fix linker error when ISAPC is disabled
Makefile: generate header file with the list of devices enabled
target/i386: kvm: Fix when nested state is needed for migration
minikconf: do not include variables from MINIKCONF_ARGS in config-all-devices.mak
target/i386: fix feature check in hyperv-stub.c
ioapic: clear irq_eoi when updating the ioapic redirect table entry
intel_iommu: Fix unexpected unmaps during global unmap
intel_iommu: Fix incorrect "end" for vtd_address_space_unmap
i386/kvm: Fix build with -m32
checkpatch: do not warn for multiline parenthesized returned value
pc: fix possible NULL pointer dereference in pc_machine_get_device_memory_region_size()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When vCPU is in VMX operation and enters SMM mode,
it temporarily exits VMX operation but KVM maintained nested-state
still stores the VMXON region physical address, i.e. even when the
vCPU is in SMM mode then (nested_state->hdr.vmx.vmxon_pa != -1ull).
Therefore, there is no need to explicitly check for
KVM_STATE_NESTED_SMM_VMXON to determine if it is necessary
to save nested-state as part of migration stream.
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20190624230514.53326-1-liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 2d384d7c8 broken the build when built with:
configure --without-default-devices --disable-user
The reason was the conversion of cpu->hyperv_synic to
cpu->hyperv_synic_kvm_only although the rest of the patch introduces a
feature checking mechanism. So I've fixed the KVM_EXIT_HYPERV_SYNIC in
hyperv-stub to do the same feature check as in the real hyperv.c
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20190624123835.28869-1-alex.bennee@linaro.org>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
find_next_bit() takes a pointer of type "const unsigned long *", but the
first argument passed here is a "uint64_t *". These types are
incompatible when compiling qemu with -m32.
Just use ctz64() instead.
Fixes: c686193072
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190624193913.28343-1-mreitz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add new version of Cascadelake-Server CPU model, setting
stepping=5 and enabling the IA32_ARCH_CAPABILITIES MSR
with some flags.
The new feature will introduce a new host software requirement,
breaking our CPU model runnability promises. This means we can't
enable the new CPU model version by default in QEMU 4.1, because
management software isn't ready yet to resolve CPU model aliases.
This is why "pc-*-4.1" will keep returning Cascadelake-Server-v1
if "-cpu Cascadelake-Server" is specified.
Includes a test case to ensure the right combinations of
machine-type + CPU model + command-line feature flags will work
as expected.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190628002844.24894-10-ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20190703221723.8161-1-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This will make unversioned CPU models behavior depend on the
machine type:
* "pc-*-4.0" and older will not report them as aliases.
This is done to keep compatibility with older QEMU versions
after management software starts translating aliases.
* "pc-*-4.1" will translate unversioned CPU models to -v1.
This is done to keep compatibility with existing management
software, that still relies on CPU model runnability promises.
* "none" will translate unversioned CPU models to their latest
version. This is planned become the default in future machine
types (probably in pc-*-4.3).
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190628002844.24894-8-ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The old CPU models will be just aliases for specific versions of
the original CPU models.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190628002844.24894-7-ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add versions of CPU models that are equivalent to their -IBRS,
-noTSX and -IBRS variants.
The separate variants will eventually be removed and become
aliases for these CPU versions.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190628002844.24894-6-ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add support for registration of multiple versions of CPU models.
The existing CPU models will be registered with a "-v1" suffix.
The -noTSX, -IBRS, and -IBPB CPU model variants will become
versions of the original models in a separate patch, so
make sure we register no versions for them.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190628002844.24894-5-ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When introducing versioned CPU models, the string at
X86CPUDefinition::model_id might not be the model-id we'll really
use. Instantiate a CPU object and check the model-id property on
"-cpu help"
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190628002844.24894-4-ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add a new option that can be used to disable feature flag
filtering. This will allow CPU model compatibility test cases to
work without host hardware dependencies.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190628002844.24894-3-ehabkost@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
SnowRidge CPU supports Accelerator Infrastrcture Architecture (MOVDIRI,
MOVDIR64B), CLDEMOTE and SPLIT_LOCK_DISABLE.
MOVDIRI, MOVDIR64B, and CLDEMOTE are found via CPUID.
The availability of SPLIT_LOCK_DISABLE is check via msr access
References can be found in either:
https://software.intel.com/en-us/articles/intel-sdmhttps://software.intel.com/en-us/download/intel-architecture-instruction-set-extensions-and-future-features-programming-reference
Signed-off-by: Paul Lai <paul.c.lai@intel.com>
Tested-by: Tao3 Xu <tao3.xu@intel.com>
Message-Id: <20190626162129.25345-1-paul.c.lai@intel.com>
[ehabkost: squashed SPLIT_LOCK_DETECT patch]
Message-Id: <20190626163232.25711-1-paul.c.lai@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The CPUID.1F as Intel V2 Extended Topology Enumeration Leaf would be
exposed if guests want to emulate multiple software-visible die within
each package. Per Intel's SDM, the 0x1f is a superset of 0xb, thus they
can be generated by almost same code as 0xb except die_offset setting.
If the number of dies per package is greater than 1, the cpuid_min_level
would be adjusted to 0x1f regardless of whether the host supports CPUID.1F.
Likewise, the CPUID.1F wouldn't be exposed if env->nr_dies < 2.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190620054525.37188-2-like.xu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The variable is completely unused, probably a leftover from
previous code clean up.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190625050008.12789-3-ehabkost@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Use the same definition as features/user_features in CPUX86State.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Message-Id: <20190620023746.9869-1-richardw.yang@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
X86CPU.hv-spinlocks is a uint32 property that has a special setter
validating the value to be no less than 0xFFF and no bigger than
UINT_MAX. The latter check is redundant; as for the former, there
appears to be no reason to prohibit the user from setting it to a lower
value.
So nuke the dedicated getter/setter pair and convert 'hv-spinlocks' to a
regular uint32 property.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20190618110659.14744-1-rkagan@virtuozzo.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The current default value for hv-spinlocks is 0xFFFFFFFF (meaning
"never retry"). However, the value is stored as a signed
integer, making the getter of the hv-spinlocks QOM property
return -1 instead of 0xFFFFFFFF.
Fix this by changing the type of X86CPU::hyperv_spinlock_attempts
to uint32_t. This has no visible effect to guest operating
systems, affecting just the behavior of the QOM getter.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190615200505.31348-1-ehabkost@redhat.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
If cpu->host_phys_bits_limit is set, QEMU will make
cpu->phys_bits be lower than host_phys_bits on some cases. This
triggers a warning that was supposed to be printed only if
phys-bits was explicitly set in the command-line.
Reorder the code so the value of cpu->phys_bits is validated
before the cpu->host_phys_bits handling. This will avoid
unexpected warnings when cpu->host_phys_bits_limit is set.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190611205420.20286-1-ehabkost@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In new sockets/dies/cores/threads model, the apicid of logical cpu could
imply die level info of guest cpu topology thus x86_apicid_from_cpu_idx()
need to be refactored with #dies value, so does apicid_*_offset().
To keep semantic compatibility, the legacy pkg_offset which helps to
generate CPUIDs such as 0x3 for L3 cache should be mapping to die_offset.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190612084104.34984-5-like.xu@linux.intel.com>
[ehabkost: squash unit test patch]
Message-Id: <20190612084104.34984-6-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The field die_id (default as 0) and has_die_id are introduced to X86CPU.
Following the legacy smp check rules, the die_id validity is added to
the same contexts as leagcy smp variables such as hmp_hotpluggable_cpus(),
machine_set_cpu_numa_node(), cpu_slot_to_string() and pc_cpu_pre_plug().
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190612084104.34984-4-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The die-level as the first PC-specific cpu topology is added to the leagcy
cpu topology model, which has one die per package implicitly and only the
numbers of sockets/cores/threads are configurable.
In the new model with die-level support, the total number of logical
processors (including offline) on board will be calculated as:
#cpus = #sockets * #dies * #cores * #threads
and considering compatibility, the default value for #dies would be
initialized to one in x86_cpu_initfn() and pc_machine_initfn().
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190612084104.34984-2-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The global smp variables in i386 are replaced with smp machine properties.
To avoid calling qdev_get_machine() as much as possible, some related funtions
for acpi data generations are refactored. No semantic changes.
A local variable of the same name would be introduced in the declaration
phase if it's used widely in the context OR replace it on the spot if it's
only used once. No semantic changes.
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Message-Id: <20190518205428.90532-8-like.xu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Commit 2d384d7c8 broken the build when built with:
configure --without-default-devices --disable-user
The reason was the conversion of cpu->hyperv_synic to
cpu->hyperv_synic_kvm_only although the rest of the patch introduces a
feature checking mechanism. So I've fixed the KVM_EXIT_HYPERV_SYNIC in
hyperv-stub to do the same feature check as in the real hyperv.c
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-14-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Move commands query-cpu-definitions, query-cpu-model-baseline,
query-cpu-model-comparison, and query-cpu-model-expansion with their
types from target.json to machine-target.json. Also move types
CpuModelInfo, CpuModelExpansionType, and CpuModelCompareResult from
misc.json there. Add machine-target.json to MAINTAINERS section
"Machine core".
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-13-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
[Commit message typo fixed]
Move commands cpu-add, query-cpus, query-cpus-fast,
query-current-machine, query-hotpluggable-cpus, query-machines,
query-memdev, and set-numa-node with their types from misc.json to new
machine.json. Also move types X86CPURegister32 and
X86CPUFeatureWordInfo. Add machine.json to MAINTAINERS section
"Machine core".
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-9-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190619201050.19040-4-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Previous commits have added support for migration of nested virtualization
workloads. This was done by utilising two new KVM capabilities:
KVM_CAP_NESTED_STATE and KVM_CAP_EXCEPTION_PAYLOAD. Both which are
required in order to correctly migrate such workloads.
Therefore, change code to add a migration blocker for vCPUs exposed with
Intel VMX or AMD SVM in case one of these kernel capabilities is
missing.
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Maran Wilson <maran.wilson@oracle.com>
Message-Id: <20190619162140.133674-11-liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Kernel commit c4f55198c7c2 ("kvm: x86: Introduce KVM_CAP_EXCEPTION_PAYLOAD")
introduced a new KVM capability which allows userspace to correctly
distinguish between pending and injected exceptions.
This distinguish is important in case of nested virtualization scenarios
because a L2 pending exception can still be intercepted by the L1 hypervisor
while a L2 injected exception cannot.
Furthermore, when an exception is attempted to be injected by QEMU,
QEMU should specify the exception payload (CR2 in case of #PF or
DR6 in case of #DB) instead of having the payload already delivered in
the respective vCPU register. Because in case exception is injected to
L2 guest and is intercepted by L1 hypervisor, then payload needs to be
reported to L1 intercept (VMExit handler) while still preserving
respective vCPU register unchanged.
This commit adds support for QEMU to properly utilise this new KVM
capability (KVM_CAP_EXCEPTION_PAYLOAD).
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20190619162140.133674-10-liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Kernel commit 8fcc4b5923af ("kvm: nVMX: Introduce KVM_CAP_NESTED_STATE")
introduced new IOCTLs to extract and restore vCPU state related to
Intel VMX & AMD SVM.
Utilize these IOCTLs to add support for migration of VMs which are
running nested hypervisors.
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Maran Wilson <maran.wilson@oracle.com>
Tested-by: Maran Wilson <maran.wilson@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20190619162140.133674-9-liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit d98f26073b ("target/i386: kvm: add VMX migration blocker")
added a migration blocker for vCPU exposed with Intel VMX.
However, migration should also be blocked for vCPU exposed with
AMD SVM.
Both cases should be blocked because QEMU should extract additional
vCPU state from KVM that should be migrated as part of vCPU VMState.
E.g. Whether vCPU is running in guest-mode or host-mode.
Fixes: d98f26073b ("target/i386: kvm: add VMX migration blocker")
Reviewed-by: Maran Wilson <maran.wilson@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20190619162140.133674-6-liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If userspace (QEMU) debug guest, when #DB is raised in guest and
intercepted by KVM, KVM forwards information on #DB to userspace
instead of injecting #DB to guest.
While doing so, KVM don't update vCPU DR6 but instead report the #DB DR6
value to userspace for further handling.
See KVM's handle_exception() DB_VECTOR handler.
QEMU handler for this case is kvm_handle_debug(). This handler basically
checks if #DB is related to one of user set hardware breakpoints and if
not, it re-inject #DB into guest.
The re-injection is done by setting env->exception_injected to #DB which
will later be passed as events.exception.nr to KVM_SET_VCPU_EVENTS ioctl
by kvm_put_vcpu_events().
However, in case userspace re-injects #DB, KVM expects userspace to set
vCPU DR6 as reported to userspace when #DB was intercepted! Otherwise,
KVM_REQ_EVENT handler will inject #DB with wrong DR6 to guest.
Fix this issue by updating vCPU DR6 appropriately when re-inject #DB to
guest.
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20190619162140.133674-5-liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Simiar to how kvm_init_vcpu() calls kvm_arch_init_vcpu() to perform
arch-dependent initialisation, introduce kvm_arch_destroy_vcpu()
to be called from kvm_destroy_vcpu() to perform arch-dependent
destruction.
This was added because some architectures (Such as i386)
currently do not free memory that it have allocated in
kvm_arch_init_vcpu().
Suggested-by: Maran Wilson <maran.wilson@oracle.com>
Reviewed-by: Maran Wilson <maran.wilson@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20190619162140.133674-3-liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit d98f26073b ("target/i386: kvm: add VMX migration blocker")
added migration blocker for vCPU exposed with Intel VMX because QEMU
doesn't yet contain code to support migration of nested virtualization
workloads.
However, that commit missed adding deletion of the migration blocker in
case init of vCPU failed. Similar to invtsc_mig_blocker. This commit fix
that issue.
Fixes: d98f26073b ("target/i386: kvm: add VMX migration blocker")
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Maran Wilson <maran.wilson@oracle.com>
Message-Id: <20190619162140.133674-2-liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MSR IA32_CORE_CAPABILITY is a feature-enumerating MSR, which only
enumerates the feature split lock detection (via bit 5) by now.
The existence of MSR IA32_CORE_CAPABILITY is enumerated by CPUID.7_0:EDX[30].
The latest kernel patches about them can be found here:
https://lkml.org/lkml/2019/4/24/1909
Signed-off-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Message-Id: <20190617153654.916-1-xiaoyao.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hyper-V on KVM can only use Synthetic timers with Direct Mode (opting for
an interrupt instead of VMBus message). This new capability is only
announced in KVM_GET_SUPPORTED_HV_CPUID.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190517141924.19024-10-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Enlightened VMCS is enabled by writing to a field in VP assist page and
these require virtual APIC.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190517141924.19024-9-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Synthetic timers operate in hv-time time and Windows won't use these
without SynIC.
Add .dependencies field to kvm_hyperv_properties[] and a generic mechanism
to check dependencies between features.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190517141924.19024-7-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In many case we just want to give Windows guests all currently supported
Hyper-V enlightenments and that's where this new mode may come handy. We
pass through what was returned by KVM_GET_SUPPORTED_HV_CPUID.
hv_cpuid_check_and_set() is modified to also set cpu->hyperv_* flags as
we may want to check them later (and we actually do for hv_runtime,
hv_synic,...).
'hv-passthrough' is a development only feature, a migration blocker is
added to prevent issues while migrating between hosts with different
feature sets.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190517141924.19024-6-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's consolidate Hyper-V features handling in hyperv_handle_properties().
The change is necessary to support 'hv-passthrough' mode as we'll be just
copying CPUIDs from KVM instead of filling them in.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190517141924.19024-4-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM now supports reporting supported Hyper-V features through CPUID
(KVM_GET_SUPPORTED_HV_CPUID ioctl). Going forward, this is going to be
the only way to announce new functionality and this has already happened
with Direct Mode stimers.
While we could just support KVM_GET_SUPPORTED_HV_CPUID for new features,
it seems to be beneficial to use it for all Hyper-V enlightenments when
possible. This way we can implement 'hv-all' pass-through mode giving the
guest all supported Hyper-V features even when QEMU knows nothing about
them.
Implementation-wise we create a new kvm_hyperv_properties structure
defining Hyper-V features, get_supported_hv_cpuid()/
get_supported_hv_cpuid_legacy() returning the supported CPUID set and
a bit over-engineered hv_cpuid_check_and_set() which we will also be
used to set cpu->hyperv_* properties for 'hv-all' mode.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190517141924.19024-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Representing Hyper-V properties as bits will allow us to check features
and dependencies between them in a natural way.
Suggested-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190517141924.19024-2-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
QEMU tracks whether a vcpu is halted using CPUState::halted. E.g.,
after initialization or reset, halted is 0 for the BSP (vcpu 0)
and 1 for the APs (vcpu 1, 2, ...). A halted vcpu should not be
handed to the hypervisor to run (e.g. hax_vcpu_run()).
Under HAXM, Android Emulator sometimes boots into a "vcpu shutdown
request" error while executing in SeaBIOS, with the HAXM driver
logging a guest triple fault in vcpu 1, 2, ... at RIP 0x3. That is
ultimately because the HAX accelerator asks HAXM to run those APs
when they are still in the halted state.
Normally, the vcpu thread for an AP will start by looping in
qemu_wait_io_event(), until the BSP kicks it via a pair of IPIs
(INIT followed by SIPI). But because the HAX accelerator does not
honor cpu->halted, it allows the AP vcpu thread to proceed to
hax_vcpu_run() as soon as it receives any kick, even if the kick
does not come from the BSP. It turns out that emulator has a
worker thread which periodically kicks every vcpu thread (possibly
to collect CPU usage data), and if one of these kicks comes before
those by the BSP, the AP will start execution from the wrong RIP,
resulting in the aforementioned SMP boot failure.
The solution is inspired by the KVM accelerator (credit to
Chuanxiao Dong <chuanxiao.dong@intel.com> for the pointer):
1. Get rid of questionable logic that unconditionally resets
cpu->halted before hax_vcpu_run(). Instead, only reset it at the
right moments (there are only a few "unhalt" events).
2. Add a check for cpu->halted before hax_vcpu_run().
Note that although the non-Unrestricted Guest (!ug_platform) code
path also forcibly resets cpu->halted, it is left untouched,
because only the UG code path supports SMP guests.
The patch is first merged to android emulator with Change-Id:
I9c5752cc737fd305d7eace1768ea12a07309d716
Cc: Yu Ning <yu.ning@intel.com>
Cc: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Message-Id: <20190610021939.13669-1-colin.xu@intel.com>
This is the common header guard idiom:
/*
* File comment
*/
#ifndef GUARD_SYMBOL_H
#define GUARD_SYMBOL_H
... actual contents ...
#endif
A few of our headers have some #include before the guard.
target/tilegx/spr_def_64.h has #ifndef __DOXYGEN__ outside the guard.
A few more have the #define elsewhere.
Change them to match the common idiom. For spr_def_64.h, that means
dropping #ifndef __DOXYGEN__. While there, rename guard symbols to
make scripts/clean-header-guards.pl happy.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190604181618.19980-2-armbru@redhat.com>
[Rebased with conflicts resolved automatically]
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
Other accelerators have their own headers: sysemu/hax.h, sysemu/hvf.h,
sysemu/kvm.h, sysemu/whpx.h. Only tcg_enabled() & friends sit in
qemu-common.h. This necessitates inclusion of qemu-common.h into
headers, which is against the rules spelled out in qemu-common.h's
file comment.
Move tcg_enabled() & friends into their own header sysemu/tcg.h, and
adjust #include directives.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-2-armbru@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
[Rebased with conflicts resolved automatically, except for
accel/tcg/tcg-all.c]
i386 (32 bit) emulation uses EFER in wrmsr and in MMU fault
processing.
But it does not included in VMState, because "efer" field is disabled with
This patch adds a section for 32-bit targets which saves EFER when
it's value is non-zero.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Message-Id: <155913371654.8429.1659082639780315242.stgit@pasha-Precision-3630-Tower>
Reviewed-by: Peter Xu <peterx@redhat.com>
[ehabkost: indentation fix]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add a "unavailable-features" QOM property to X86CPU objects that
have the same semantics of "unavailable-features" on
query-cpu-definitions. The new property has the same goal of
"filtered-features", but is generic enough to let any kind of CPU
feature to be listed there without relying on low level details
like CPUID leaves or MSR numbers.
Message-Id: <20190422234742.15780-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Extract feature name listing code from
x86_cpu_class_check_missing_features(). It will be reused to
return information about CPU filtered features at runtime.
Message-Id: <20190422234742.15780-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This macro is now always empty, so remove it. This leaves the
entire contents of CPUArchState under the control of the guest
architecture.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Nothing in there so far, but all of the plumbing done
within the target ArchCPU state.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Consolidate some boilerplate from foo_cpu_initfn.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that we have ArchCPU, we can define this generically,
in the one place that needs it.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Cleanup in the boilerplate that each target must define.
Replace x86_env_get_cpu with env_archcpu. The combination
CPU(x86_env_get_cpu) should have used ENV_GET_CPU to begin;
use env_cpu now.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now that we have both ArchCPU and CPUArchState, we can define
this generically instead of via macro in each target's cpu.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For all targets, do this just before including exec/cpu-all.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For all targets, do this just before including exec/cpu-all.h.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
For all targets, into this new file move TARGET_LONG_BITS,
TARGET_PAGE_BITS, TARGET_PHYS_ADDR_SPACE_BITS,
TARGET_VIRT_ADDR_SPACE_BITS, and NB_MMU_MODES.
Include this new file from exec/cpu-defs.h.
This now removes the somewhat odd requirement that target/arch/cpu.h
defines TARGET_LONG_BITS before including exec/cpu-defs.h, so push the
bulk of the includes within target/arch/cpu.h to the top.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The CPUID.01H:ECX[bit 3] ought to mirror the value of the MSR
IA32_MISC_ENABLE MWAIT bit and as userspace has control of them
both, it is userspace's job to configure both bits to match on
the initial setup.
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1557813999-9175-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use qemu_guest_getrandom in aspeed, nrf51, bcm2835, exynos4210 rng devices.
Use qemu_guest_getrandom in target/ppc darn instruction.
Support ARMv8.5-RNG extension.
Support x86 RDRAND extension.
Acked-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAlzllrsdHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV9/qAgAuYpF/gHrkfT+IFrw
OsgV1pPdhh+opxp44ayIQ6VC64voij0k/NnmC3/BxRv89yPqchvA6m0c2jzfGuwZ
ICpDt7LvFTrG9k8X9vEXbOTfh5dS/5g1o0LXiGU9RmMaC/5z2ZIabxU8K1Ti3+X0
P3B5s65rRQ8fPzOAMLEjeaHYQ/AOX/CNsmgFDve+d0b9tJY99UVO3Pb0h3+eR0s3
/4AHWG+IACGX7MVgFIfkEbGVnwboNiT20MUq3Exn2yGgg0IbLfoUazOnbfRz9jkX
kbN6nAZ+WDynf31SvvkEL/P6W5medf58ufJOiBB8opIp1E4WDdM30V8RkkPOyj4z
YOBmSw==
=2RnL
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/rth/tags/pull-rng-20190522' into staging
Introduce qemu_guest_getrandom.
Use qemu_guest_getrandom in aspeed, nrf51, bcm2835, exynos4210 rng devices.
Use qemu_guest_getrandom in target/ppc darn instruction.
Support ARMv8.5-RNG extension.
Support x86 RDRAND extension.
Acked-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
# gpg: Signature made Wed 22 May 2019 19:36:43 BST
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* remotes/rth/tags/pull-rng-20190522: (25 commits)
target/i386: Implement CPUID_EXT_RDRAND
target/ppc: Use qemu_guest_getrandom for DARN
target/ppc: Use gen_io_start/end around DARN
target/arm: Implement ARMv8.5-RNG
target/arm: Put all PAC keys into a structure
hw/misc/exynos4210_rng: Use qemu_guest_getrandom
hw/misc/bcm2835_rng: Use qemu_guest_getrandom_nofail
hw/misc/nrf51_rng: Use qemu_guest_getrandom_nofail
aspeed/scu: Use qemu_guest_getrandom_nofail
linux-user: Remove srand call
linux-user/aarch64: Use qemu_guest_getrandom for PAUTH keys
linux-user: Use qemu_guest_getrandom_nofail for AT_RANDOM
linux-user: Call qcrypto_init if not using -seed
linux-user: Initialize pseudo-random seeds for all guest cpus
cpus: Initialize pseudo-random seeds for all guest cpus
util: Add qemu_guest_getrandom and associated routines
ui/vnc: Use gcrypto_random_bytes for start_auth_vnc
ui/vnc: Split out authentication_failed
crypto: Change the qcrypto_random_bytes buffer type to void*
crypto: Use getrandom for qcrypto_random_bytes
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We now have an interface for guest visible random numbers.
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Microarchitectural Data Sampling is a hardware vulnerability which allows
unprivileged speculative access to data which is available in various CPU
internal buffers.
Some Intel processors use the ARCH_CAP_MDS_NO bit in the
IA32_ARCH_CAPABILITIES
MSR to report that they are not vulnerable, make it available to guests.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20190516185320.28340-1-pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
md-clear is a new CPUID bit which is set when microcode provides the
mechanism to invoke a flush of various exploitable CPU buffers by invoking
the VERW instruction.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20190515141011.5315-2-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
"megasas: fix mapped frame size" from Peter Lieven.
In addition, -realtime is marked as deprecated.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJc3rY3AAoJEL/70l94x66D91kH/21LLnL+sKmyueSM/Sek4id2
r06tHdGMdl5Od3I5uMD9gnr4AriiCZc9ybQDQ1N879wKMmQPZwcnf2GJ5DZ0wa3L
jHoQO07Bg0KZGWALjXiN5PWB0DlJtXsTm0C4q4tnt6V/ueasjxouBk9/fRLRc09n
QTS379X9QvPElFTv3WPfGz6kmkLq8VMmdRnSlXneB9xTyXXJbFj3zlvDCElNSgWh
fZ7gnfYWB1LOC19HJxp1mJSkAUD5AgImYEK1Hmnr+BMs2sg6gypYNtp3LtE5FzmZ
HSdXYFyPkQV9UyTiV1XBs3bXJbGYj5OApfXCtwo/I2JtP+LhHBA2eq1Gs3QgP98=
=zSSj
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
Mostly bugfixes and cleanups, the most important being
"megasas: fix mapped frame size" from Peter Lieven.
In addition, -realtime is marked as deprecated.
# gpg: Signature made Fri 17 May 2019 14:25:11 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (21 commits)
hw/net/ne2000: Extract the PCI device from the chipset common code
hw/char: Move multi-serial devices into separate file
ioapic: allow buggy guests mishandling level-triggered interrupts to make progress
build: don't build hardware objects with linux-user
build: chardev is only needed for softmmu targets
configure: qemu-ga is only needed with softmmu targets
build: replace GENERATED_FILES by generated-files-y
trace: only include trace-event-subdirs when they are needed
sun4m: obey -vga none
mips-fulong2e: obey -vga none
hw/i386/acpi: Assert a pointer is not null BEFORE using it
hw/i386/acpi: Add object_resolve_type_unambiguous to improve modularity
hw/acpi/piix4: Move TYPE_PIIX4_PM to a public header
memory: correct the comment to DIRTY_MEMORY_MIGRATION
vl: fix -sandbox parsing crash when seccomp support is disabled
hvf: Add missing break statement
megasas: fix mapped frame size
vl: Add missing descriptions to the VGA adapters list
Declare -realtime as deprecated
roms: assert if max rom size is less than the used size
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In target/i386/hvf/hvf.c, a break statement was probably missing in
`hvf_vcpu_exec()`, in handling EXIT_REASON_HLT.
These lines seemed to be equivalent to `kvm_handle_halt()`.
Signed-off-by: Chen Zhang <tgfbeta@me.com>
Message-Id: <087F1D9C-109D-41D1-BE2C-CE5D840C981B@me.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Improve tlb_vaddr_to_host for use by ARM SVE no-fault loads.
-----BEGIN PGP SIGNATURE-----
iQFRBAABCgA7FiEEekgeeIaLTbaoWgXAZN846K9+IV8FAlzVx4UdHHJpY2hhcmQu
aGVuZGVyc29uQGxpbmFyby5vcmcACgkQZN846K9+IV+U1Af/b3cV5d5a1LWRdLgR
71JCPK/M3o43r2U9wCSikteXkmNBEdEoc5+WRk2SuZFLW/JB1DHDY7/gISPIhfoB
ZIza2TxD/QK1CQ5/mMWruKBlyygbYYZgsYaaNsMJRJgicgOSjTN0nuHMbIfv3tAN
mu+IlkD0LdhVjP0fz30Jpew3b3575RCjYxEPM6KQI3RxtQFjZ3FhqV5hKR4vtdP5
yLWJQzwAbaCB3SZUvvp7TN1ZsmeyLpc+Yz/YtRTqQedo7SNWWBKldLhqq4bZnH1I
AkzHbtWIOBrjWJ34ZMAgI5Q56Du9TBbBvCdM9azmrQjSu/2kdsPBPcUyOpnUCsCx
NyXo9g==
=x71l
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/rth/tags/pull-tcg-20190510' into staging
Add CPUClass::tlb_fill.
Improve tlb_vaddr_to_host for use by ARM SVE no-fault loads.
# gpg: Signature made Fri 10 May 2019 19:48:37 BST
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* remotes/rth/tags/pull-tcg-20190510: (27 commits)
tcg: Use tlb_fill probe from tlb_vaddr_to_host
tcg: Remove CPUClass::handle_mmu_fault
tcg: Use CPUClass::tlb_fill in cputlb.c
target/xtensa: Convert to CPUClass::tlb_fill
target/unicore32: Convert to CPUClass::tlb_fill
target/tricore: Convert to CPUClass::tlb_fill
target/tilegx: Convert to CPUClass::tlb_fill
target/sparc: Convert to CPUClass::tlb_fill
target/sh4: Convert to CPUClass::tlb_fill
target/s390x: Convert to CPUClass::tlb_fill
target/riscv: Convert to CPUClass::tlb_fill
target/ppc: Convert to CPUClass::tlb_fill
target/openrisc: Convert to CPUClass::tlb_fill
target/nios2: Convert to CPUClass::tlb_fill
target/moxie: Convert to CPUClass::tlb_fill
target/mips: Convert to CPUClass::tlb_fill
target/mips: Tidy control flow in mips_cpu_handle_mmu_fault
target/mips: Pass a valid error to raise_mmu_exception for user-only
target/microblaze: Convert to CPUClass::tlb_fill
target/m68k: Convert to CPUClass::tlb_fill
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We commonly define the header guard symbol without an explicit value.
Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-8-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Leading underscores are ill-advised because such identifiers are
reserved. Trailing underscores are merely ugly. Strip both.
Our header guards commonly end in _H. Normalize the exceptions.
Done with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-7-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Changes to slirp/ dropped, as we're about to spin it off]
Header guard symbols should match their file name to make guard
collisions less likely.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-6-armbru@redhat.com>
[Rebase to master: update include/hw/net/ne2000-isa.h]
We can now use the CPUClass hook instead of a named function.
Create a static tlb_fill function to avoid other changes within
cputlb.c. This also isolates the asserts within. Remove the
named tlb_fill function from all of the targets.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We do not support probing, but we do not need it yet either.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add a new base CPU model called 'Dhyana' to model processors from Hygon
Dhyana(family 18h), which derived from AMD EPYC(family 17h).
The following features bits have been removed compare to AMD EPYC:
aes, pclmulqdq, sha_ni
The Hygon Dhyana support to KVM in Linux is already accepted upstream[1].
So add Hygon Dhyana support to Qemu is necessary to create Hygon's own
CPU model.
Reference:
[1] https://git.kernel.org/tip/fec98069fb72fb656304a3e52265e0c2fc9adf87
Signed-off-by: Pu Wen <puwen@hygon.cn>
Message-Id: <1555416373-28690-1-git-send-email-puwen@hygon.cn>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In order to handle TB's that translate to too much code, we
need to place the control of the length of the translation
in the hands of the code gen master loop.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
CPUClass method dump_statistics() takes an fprintf()-like callback and
a FILE * to pass to it. Most callers pass fprintf() and stderr.
log_cpu_state() passes fprintf() and qemu_log_file.
hmp_info_registers() passes monitor_fprintf() and the current monitor
cast to FILE *. monitor_fprintf() casts it right back, and is
otherwise identical to monitor_printf().
The callback gets passed around a lot, which is tiresome. The
type-punning around monitor_fprintf() is ugly.
Drop the callback, and call qemu_fprintf() instead. Also gets rid of
the type-punning, since qemu_fprintf() takes NULL instead of the
current monitor cast to FILE *.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190417191805.28198-15-armbru@redhat.com>
x86_cpu_dump_local_apic_state() takes an fprintf()-like callback and a
FILE * to pass to it, and so do its helper functions.
Its only caller hmp_info_local_apic() passes monitor_fprintf() and the
current monitor cast to FILE *. monitor_fprintf() casts it right
back, and is otherwise identical to monitor_printf(). The
type-punning is ugly.
Drop the callback, and call qemu_printf() instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20190417191805.28198-12-armbru@redhat.com>
The various TARGET_cpu_list() take an fprintf()-like callback and a
FILE * to pass to it. Their callers (vl.c's main() via list_cpus(),
bsd-user/main.c's main(), linux-user/main.c's main()) all pass
fprintf() and stdout. Thus, the flexibility provided by the (rather
tiresome) indirection isn't actually used.
Drop the callback, and call qemu_printf() instead.
Calling printf() would also work, but would make the code unsuitable
for monitor context without making it simpler.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190417191805.28198-10-armbru@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Fix a TCG crash due to attempting an atomic increment
operation without having set up the address first.
This is a similar case to that dealt with in commit
e84fcd7f66, and we fix it in the same way.
Fixes: https://bugs.launchpad.net/qemu/+bug/1807675
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20190328104750.25046-1-peter.maydell@linaro.org
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to
source files. That's because when trace-events got split up, the
comments were moved verbatim.
Delete the sub/dir/ part from these comments. Gets rid of several
misspellings.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190314180929.27722-3-armbru@redhat.com
Message-Id: <20190314180929.27722-3-armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Currently, the Cascadelake-Server, Icelake-Client, and
Icelake-Server are always generating the following warning:
qemu-system-x86_64: warning: \
host doesn't support requested feature: CPUID.07H:ECX [bit 4]
This happens because OSPKE was never returned by
GET_SUPPORTED_CPUID or x86_cpu_get_supported_feature_word().
OSPKE is a runtime flag automatically set by the KVM module or by
TCG code, was always cleared by x86_cpu_filter_features(), and
was not supposed to appear on the CPU model table.
Remove the OSPKE flag from the CPU model table entries, to avoid
the bogus warning and avoid returning invalid feature data on
query-cpu-* QMP commands. As OSPKE was always cleared by
x86_cpu_filter_features(), this won't have any guest-visible
impact.
Include a test case that should detect the problem if we introduce
a similar bug again.
Fixes: c7a88b52f6 ("i386: Add new model of Cascadelake-Server")
Fixes: 8a11c62da9 ("i386: Add new CPU model Icelake-{Server,Client}")
Cc: Tao Xu <tao3.xu@intel.com>
Cc: Robert Hoo <robert.hu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190319200515.14999-1-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Now that kvm_arch_get_supported_cpuid() will only return
arch_capabilities if QEMU is able to initialize the MSR properly,
we know that the feature is safely migratable.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190125220606.4864-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
KVM has two bugs in the handling of MSR_IA32_ARCH_CAPABILITIES:
1) Linux commit commit 1eaafe91a0df ("kvm: x86: IA32_ARCH_CAPABILITIES
is always supported") makes GET_SUPPORTED_CPUID return
arch_capabilities even if running on SVM. This makes "-cpu
host,migratable=off" incorrectly expose arch_capabilities on CPUID on
AMD hosts (where the MSR is not emulated by KVM).
2) KVM_GET_MSR_INDEX_LIST does not return MSR_IA32_ARCH_CAPABILITIES if
the MSR is not supported by the host CPU. This makes QEMU not
initialize the MSR properly at kvm_put_msrs() on those hosts.
Work around both bugs on the QEMU side, by checking if the MSR
was returned by KVM_GET_MSR_INDEX_LIST before returning the
feature flag on kvm_arch_get_supported_cpuid().
This has the unfortunate side effect of making arch_capabilities
unavailable on hosts without hardware support for the MSR until bug #2
is fixed on KVM, but I can't see another way to work around bug #1
without that side effect.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20190125220606.4864-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The RAM device presents a memory region that should be handled
as an IO region and should not be pinned.
In the case of the vfio-pci, RAM device represents a MMIO BAR
and the memory region is not backed by pages hence
KVM_MEMORY_ENCRYPT_REG_REGION fails to lock the memory range.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1667249
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Message-Id: <20190204222322.26766-3-brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel Processor Trace required CPUID[0x14] but the cpuid_level
have no change when create a kvm guest with
e.g. "-cpu qemu64,+intel-pt".
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Luwei Kang <luwei.kang@intel.com>
Message-Id: <1548805979-12321-1-git-send-email-luwei.kang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The CPUID code will call kvm_arch_get_supported_cpuid() and, even though
it is undef kvm_enabled() so it never runs for user-mode emulators,
sometimes clang will not optimize it out at -O0.
That could be considered a compiler bug, however at -O0 we give it
a pass and just add the stubs.
Reported-by: Kamil Rytarowski <n54@gmx.com>
Tested-by: Kamil Rytarowski <n54@gmx.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move rtc-reset-reinjection and SEV in target.json and make them
conditional on TARGET_I386.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190214152251.2073-10-armbru@redhat.com>
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The machine that with hvf accelerator and smp sometimes boot hangs
because all processors are executing instructions at startup,
including early I/O emulations. We should just allow the bootstrap
processor to initialize the machine and then to wake up slave
processors by interrupt.
Signed-off-by: Heiher <r@hev.cc>
Message-Id: <20190123073402.28465-1-r@hev.cc>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The machine description we send is being (silently) thrown on the floor
by GDB and GDB silently uses the default machine description, because
the xml parse fails on <feature> nested within <feature>.
Changes to the xml in qemu source code have no effect.
In addition, the default machine description has fs_base, which fails to
be retrieved, which breaks the whole register window. Add it and the
other control registers.
Signed-off-by: Doug Gale <doug16k@gmail.com>
Message-Id: <20190124040457.2546-1-doug16k@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In 16-bit addressing mode, when Mod = 0 and R/M = 6, decoded displacement
doesn't reach decode_linear_addr and gets lost. Instructions that
involve the combination of ModRM always get a pointer with zero offset
from the beginning of DS segment.
The change fixes drawing in F-BIRD from day 1 of '18 advent calendar.
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20190125154743.14498-1-r.bolshakov@yadro.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
MPX support is being phased out by Intel and actually I am not sure that
OS X has ever enabled it in XCR0. Drop it from the Hypervisor.framework
acceleration.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This reverts commit 5131dc433d.
For new instruction 'PCONFIG' will not be exposed to guest.
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1545227081-213696-3-git-send-email-robert.hu@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Processor tracing is not yet implemented for KVM and it will be an
opt in feature requiring a special module parameter.
Disable it, because it is wrong to enable it by default and
it is impossible that no one has ever used it.
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PCONFIG is not available to guests; it must be specifically enabled
using the PCONFIG_ENABLE execution control. Disable it, because
no one can ever use it.
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1545227081-213696-2-git-send-email-robert.hu@linux.intel.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- code clean-up
- LGPL information clean-up
- fix typo (acpi)
-----BEGIN PGP SIGNATURE-----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=1OOM
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-pull-request' into staging
- add device category (edu, i8042, sd memory card)
- code clean-up
- LGPL information clean-up
- fix typo (acpi)
# gpg: Signature made Wed 30 Jan 2019 13:21:50 GMT
# gpg: using RSA key F30C38BD3F2FBE3C
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-pull-request:
virtio-blk: remove duplicate definition of VirtIOBlock *s pointer
hw/block: clean up stale xen_disk trace entries
target/m68k: Fix LGPL information in the file headers
target/s390x: Fix LGPL version in the file header comments
tcg: Fix LGPL version number
target/tricore: Fix LGPL version number
target/openrisc: Fix LGPL version number
COPYING.LIB: Synchronize the LGPL 2.1 with the version from gnu.org
Don't talk about the LGPL if the file is licensed under the GPL
hw: sd: set category of the sd memory card
hw: input: set category of the i8042 device
typo: apci->acpi
hw: edu: set category of the edu device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some files claim that the code is licensed under the GPL, but then
suddenly suggest that the user should have a look at the LGPL.
That's of course non-sense, replace it with the correct GPL wording
instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1548255083-8190-1-git-send-email-thuth@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Modern AMD CPUs support NPT and NRIPSAVE features and KVM exposes these
when present. NRIPSAVE apeared somewhere in Opteron_G3 lifetime (e.g.
QuadCore AMD Opteron 2378 has is but QuadCore AMD Opteron HE 2344 doesn't),
NPT was introduced a bit earlier.
Add the FEAT_SVM leaf to Opteron_G4/G5 and EPYC/EPYC-IBPB cpu models.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20190121155051.5628-1-vkuznets@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Update the stepping from 5 to 6, in order that
the Cascadelake-Server CPU model can support AVX512VNNI
and MSR based features exposed by ARCH_CAPABILITIES.
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20181227024304.12182-2-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Hyper-V .feat_names are, unlike hardware features, commented out and it is
not obvious why we do that. Document the current status quo.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20181221141604.16935-1-vkuznets@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some downstream distributions of QEMU set host-phys-bits=on by
default. This worked very well for most use cases, because
phys-bits really didn't have huge consequences. The only
difference was on the CPUID data seen by guests, and on the
handling of reserved bits.
This changed in KVM commit 855feb673640 ("KVM: MMU: Add 5 level
EPT & Shadow page table support"). Now choosing a large
phys-bits value for a VM has bigger impact: it will make KVM use
5-level EPT even when it's not really necessary. This means
using the host phys-bits value may not be the best choice.
Management software could address this problem by manually
configuring phys-bits depending on the size of the VM and the
amount of MMIO address space required for hotplug. But this is
not trivial to implement.
However, there's another workaround that would work for most
cases: keep using the host phys-bits value, but only if it's
smaller than 48. This patch makes this possible by introducing a
new "-cpu" option: "host-phys-bits-limit". Management software
or users can make sure they will always use 4-level EPT using:
"host-phys-bits=on,host-phys-bits-limit=48".
This behavior is still not enabled by default because QEMU
doesn't enable host-phys-bits=on by default. But users,
management software, or downstream distributions may choose to
change their defaults using the new option.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20181211192527.13254-1-ehabkost@redhat.com>
[ehabkost: removed test code while some issues are addressed]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
MPX support is being phased out by Intel; GCC has dropped it, Linux
is also going to do that. Even though KVM will have special code
to support MPX after the kernel proper stops enabling it in XCR0,
we probably also want to deprecate that in a few years. As a start,
do not enable it by default for any named CPU model starting with
the 4.0 machine types; this include Skylake, Icelake and Cascadelake.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181220121100.21554-1-pbonzini@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The missing functionality was added ~3 years ago with the Linux commit
46896c73c1a4 ("KVM: svm: add support for RDTSCP")
so reenable RDTSCP support on those CPU models.
Opteron_G2 - being family 15, model 6, doesn't have RDTSCP support
(the real hardware doesn't have it. K8 got RDTSCP support with the NPT
models, i.e., models >= 0x40).
Document the host's minimum required kernel version, while at it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Message-ID: <20181212200803.GG6653@zn.tnic>
[ehabkost: moved compat properties code to pc.c]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
It was found that QMP users of QEMU (e.g. libvirt) may need
HV_CPUID_ENLIGHTMENT_INFO.EAX/HV_CPUID_NESTED_FEATURES.EAX information. In
particular, 'hv_tlbflush' and 'hv_evmcs' enlightenments are only exposed in
HV_CPUID_ENLIGHTMENT_INFO.EAX.
HV_CPUID_NESTED_FEATURES.EAX is exposed for two reasons: convenience
(we don't need to export it from hyperv_handle_properties() and as
future-proof for Enlightened MSR-Bitmap, PV EPT invalidation and
direct virtual flush features.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20181126135958.20956-1-vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Most files that have TABs only contain a handful of them. Change
them to spaces so that we don't confuse people.
disas, standard-headers, linux-headers and libdecnumber are imported
from other projects and probably should be exempted from the check.
Outside those, after this patch the following files still contain both
8-space and TAB sequences at the beginning of the line. Many of them
have a majority of TABs, or were initially committed with all tabs.
bsd-user/i386/target_syscall.h
bsd-user/x86_64/target_syscall.h
crypto/aes.c
hw/audio/fmopl.c
hw/audio/fmopl.h
hw/block/tc58128.c
hw/display/cirrus_vga.c
hw/display/xenfb.c
hw/dma/etraxfs_dma.c
hw/intc/sh_intc.c
hw/misc/mst_fpga.c
hw/net/pcnet.c
hw/sh4/sh7750.c
hw/timer/m48t59.c
hw/timer/sh_timer.c
include/crypto/aes.h
include/disas/bfd.h
include/hw/sh4/sh.h
libdecnumber/decNumber.c
linux-headers/asm-generic/unistd.h
linux-headers/linux/kvm.h
linux-user/alpha/target_syscall.h
linux-user/arm/nwfpe/double_cpdo.c
linux-user/arm/nwfpe/fpa11_cpdt.c
linux-user/arm/nwfpe/fpa11_cprt.c
linux-user/arm/nwfpe/fpa11.h
linux-user/flat.h
linux-user/flatload.c
linux-user/i386/target_syscall.h
linux-user/ppc/target_syscall.h
linux-user/sparc/target_syscall.h
linux-user/syscall.c
linux-user/syscall_defs.h
linux-user/x86_64/target_syscall.h
slirp/cksum.c
slirp/if.c
slirp/ip.h
slirp/ip_icmp.c
slirp/ip_icmp.h
slirp/ip_input.c
slirp/ip_output.c
slirp/mbuf.c
slirp/misc.c
slirp/sbuf.c
slirp/socket.c
slirp/socket.h
slirp/tcp_input.c
slirp/tcpip.h
slirp/tcp_output.c
slirp/tcp_subr.c
slirp/tcp_timer.c
slirp/tftp.c
slirp/udp.c
slirp/udp.h
target/cris/cpu.h
target/cris/mmu.c
target/cris/op_helper.c
target/sh4/helper.c
target/sh4/op_helper.c
target/sh4/translate.c
tcg/sparc/tcg-target.inc.c
tests/tcg/cris/check_addo.c
tests/tcg/cris/check_moveq.c
tests/tcg/cris/check_swap.c
tests/tcg/multiarch/test-mmap.c
ui/vnc-enc-hextile-template.h
ui/vnc-enc-zywrle.h
util/envlist.c
util/readline.c
The following have only TABs:
bsd-user/i386/target_signal.h
bsd-user/sparc64/target_signal.h
bsd-user/sparc64/target_syscall.h
bsd-user/sparc/target_signal.h
bsd-user/sparc/target_syscall.h
bsd-user/x86_64/target_signal.h
crypto/desrfb.c
hw/audio/intel-hda-defs.h
hw/core/uboot_image.h
hw/sh4/sh7750_regnames.c
hw/sh4/sh7750_regs.h
include/hw/cris/etraxfs_dma.h
linux-user/alpha/termbits.h
linux-user/arm/nwfpe/fpopcode.h
linux-user/arm/nwfpe/fpsr.h
linux-user/arm/syscall_nr.h
linux-user/arm/target_signal.h
linux-user/cris/target_signal.h
linux-user/i386/target_signal.h
linux-user/linux_loop.h
linux-user/m68k/target_signal.h
linux-user/microblaze/target_signal.h
linux-user/mips64/target_signal.h
linux-user/mips/target_signal.h
linux-user/mips/target_syscall.h
linux-user/mips/termbits.h
linux-user/ppc/target_signal.h
linux-user/sh4/target_signal.h
linux-user/sh4/termbits.h
linux-user/sparc64/target_syscall.h
linux-user/sparc/target_signal.h
linux-user/x86_64/target_signal.h
linux-user/x86_64/termbits.h
pc-bios/optionrom/optionrom.h
slirp/mbuf.h
slirp/misc.h
slirp/sbuf.h
slirp/tcp.h
slirp/tcp_timer.h
slirp/tcp_var.h
target/i386/svm.h
target/sparc/asi.h
target/xtensa/core-dc232b/xtensa-modules.inc.c
target/xtensa/core-dc233c/xtensa-modules.inc.c
target/xtensa/core-de212/core-isa.h
target/xtensa/core-de212/xtensa-modules.inc.c
target/xtensa/core-fsf/xtensa-modules.inc.c
target/xtensa/core-sample_controller/core-isa.h
target/xtensa/core-sample_controller/xtensa-modules.inc.c
target/xtensa/core-test_kc705_be/core-isa.h
target/xtensa/core-test_kc705_be/xtensa-modules.inc.c
tests/tcg/cris/check_abs.c
tests/tcg/cris/check_addc.c
tests/tcg/cris/check_addcm.c
tests/tcg/cris/check_addoq.c
tests/tcg/cris/check_bound.c
tests/tcg/cris/check_ftag.c
tests/tcg/cris/check_int64.c
tests/tcg/cris/check_lz.c
tests/tcg/cris/check_openpf5.c
tests/tcg/cris/check_sigalrm.c
tests/tcg/cris/crisutils.h
tests/tcg/cris/sys.c
tests/tcg/i386/test-i386-ssse3.c
ui/vgafont.h
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20181213223737.11793-3-pbonzini@redhat.com>
Reviewed-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Wainer dos Santos Moschetta <wainersm@redhat.com>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Stefan Markovic <smarkovic@wavecomp.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Most list head structs need not be given a name. In most cases the
name is given just in case one is going to use QTAILQ_LAST, QTAILQ_PREV
or reverse iteration, but this does not apply to lists of other kinds,
and even for QTAILQ in practice this is only rarely needed. In addition,
we will soon reimplement those macros completely so that they do not
need a name for the head struct. So clean up everything, not giving a
name except in the rare case where it is necessary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Intel HAXM supports now 32-bit and 64-bit Linux hosts. This patch includes
the corresponding userland changes.
Since the Darwin userland backend is POSIX-compliant, the hax-darwin.{c,h}
files have been renamed to hax-posix.{c,h}. This prefix is consistent with
the naming used in the rest of QEMU.
Signed-off-by: Alexandro Sanchez Bach <asanchez@kryptoslogic.com>
Message-Id: <20181115013331.65820-1-asanchez@kryptoslogic.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All qdev_prop_register_global() set &error_fatal for errp, except
'-rtc driftfix=slew', which arguably should also use &error_fatal, as
otherwise failing to apply the property would only report a warning.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes, with the changes
to the following files manually reverted:
contrib/libvhost-user/libvhost-user-glib.h
contrib/libvhost-user/libvhost-user.c
contrib/libvhost-user/libvhost-user.h
linux-user/mips64/cpu_loop.c
linux-user/mips64/signal.c
linux-user/sparc64/cpu_loop.c
linux-user/sparc64/signal.c
linux-user/x86_64/cpu_loop.c
linux-user/x86_64/signal.c
target/s390x/gen-features.c
tests/migration/s390x/a-b-bios.c
tests/test-rcu-simpleq.c
tests/test-rcu-tailq.c
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20181204172535.2799-1-armbru@redhat.com>
Acked-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Halil Pasic <pasic@linux.ibm.com>
Acked-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Viktor Prutyanov <viktor.prutyanov@phystech.edu>
It's going to clutter QEMU logs if 0x0f00 is trapped.
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20181203100415.53027-2-r.bolshakov@yadro.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
The STIBP flag may be supported by the host KVM module, so QEMU
can allow it to be configured manually, and it can be exposed to
guests when using "-cpu host".
No additional migration code is required because the whole
contents of spec_ctrl is already migrated in the "cpu/spec_ctrl"
section.
Corresponding KVM patch was submitted at:
https://lore.kernel.org/lkml/20181205191956.31480-1-ehabkost@redhat.com/
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20181210180250.31299-1-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
clang complains about taking the address of a packed
member of a struct:
target/i386/kvm.c:1245:27: warning: taking address of packed member 'cpuid' of class or structure '' may result in an unaligned pointer value [-Waddress-of-packed-member]
c = cpuid_find_entry(&cpuid_data.cpuid, 1, 0);
^~~~~~~~~~~~~~~~
target/i386/kvm.c:1297:31: warning: taking address of packed member 'cpuid' of class or structure '' may result in an unaligned pointer value [-Waddress-of-packed-member]
c = cpuid_find_entry(&cpuid_data.cpuid, kvm_base, 0);
^~~~~~~~~~~~~~~~
The kernel's definitions of struct kvm_cpuid2 and struct
kvm_cpuid_entry2 are carefully set up with padding fields
so that there is no between-struct padding anyway, so
the QEMU_PACKED annotation is unnecessary and might result
in the compiler generating worse code. Drop it, and instead
assert at build time that there is no stray padding.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20181210114654.31433-1-peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
MOVDIR64B moves 64-bytes as direct-store with 64-bytes write atomicity.
Direct store is implemented by using write combining (WC) for writing
data directly into memory without caching the data.
The bit definition:
CPUID.(EAX=7,ECX=0):ECX[bit 28] MOVDIR64B
The release document ref below link:
https://software.intel.com/sites/default/files/managed/c5/15/\
architecture-instruction-set-extensions-programming-reference.pdf
Cc: Xu Tao <tao3.xu@intel.com>
Signed-off-by: Liu Jingqi <jingqi.liu@intel.com>
Message-Id: <1541488407-17045-3-git-send-email-jingqi.liu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
MOVDIRI moves doubleword or quadword from register to memory through
direct store which is implemented by using write combining (WC) for
writing data directly into memory without caching the data.
The bit definition:
CPUID.(EAX=7,ECX=0):ECX[bit 27] MOVDIRI
The release document ref below link:
https://software.intel.com/sites/default/files/managed/c5/15/\
architecture-instruction-set-extensions-programming-reference.pdf
Cc: Xu Tao <tao3.xu@intel.com>
Signed-off-by: Liu Jingqi <jingqi.liu@intel.com>
Message-Id: <1541488407-17045-2-git-send-email-jingqi.liu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
And also the g_malloc doesn't need check return value,
remove it.
Cc: qemu-trivial@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Li Qiang <liq3ea@gmail.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <1543226179-5135-1-git-send-email-liq3ea@gmail.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Single opcode instructions in ff group were incorrectly processed
because an overrun of _decode_tbl1[0xff] resulted in access of
_decode_tbl2[0x0]. Thus, decode_sldtgroup was called instead of
decode_ffgroup:
7d71: decode_sldtgroup: 1
Unimplemented handler (7d71) for 108 (ff 0)
While at it correct maximum length for _decode_tbl2 and _decode_tbl3.
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixes a TCG crash due to attempting the atomic operation without
having set up the address first. This does not attempt to fix
all of the other missing checks for LOCK.
Fixes: a7cee522f3
Fixes: https://bugs.launchpad.net/qemu/+bug/1803160
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20181113193510.24862-1-richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is really no difference between live migration and savevm, except
that savevm does not require bdrv_invalidate_cache to be implemented
by all disks. However, it is unlikely that savevm is used with anything
except qcow2 disks, so the penalty is small and worth the improvement
in catching bad usage of savevm.
Only one place was taking care of savevm when adding a migration blocker,
and it can be removed.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Nested VMX does not support live migration yet. Add a blocker
until that is worked out.
Nested SVM only does not support it, but unfortunately it is
enabled by default for -cpu host so we cannot really disable it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When writing to guest's MSR_IA32_ARCH_CAPABILITIES, check whether it's
supported in the guest using the KVM_GET_MSR_INDEX_LIST ioctl.
Fixes: d86f963694
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Tested-by: balducci@units.it
Signed-off-by: Bandan Das <bsd@redhat.com>
Message-Id: <jpg4lc4iiav.fsf_-_@linux.bootlegged.copy>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Fix the SYSCALL instruction in 64-bit (long mode). The RF flag
should be cleared in R11 as well as in the RFLAGS. Intel
and AMD CPUs behave same. AMD has this documented in the
APM vol 3.
Signed-off-by: Roman Kapl <rka@sysgo.com>
Signed-off-by: Rudolf Marek <rudolf.marek@sysgo.com>
Message-Id: <20181019122449.26387-1-rka@sysgo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Adds a new CPU flag to enable the Enlightened VMCS KVM feature.
QEMU enables KVM_CAP_HYPERV_ENLIGHTENED_VMCS and gets back the
version to be advertised in lower 16 bits of CPUID.0x4000000A:EAX.
Suggested-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20181022165506.30332-3-vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As the release document ref below link (page 13):
https://software.intel.com/sites/default/files/managed/c5/15/\
architecture-instruction-set-extensions-programming-reference.pdf
PKU is supported in Skylake Server (Only Server) and later, and
on Intel(R) Xeon(R) Processor Scalable Family. So PKU is supposed
to be in Skylake-Server CPU model. And PKU's CPUID has been
exposed to QEMU. But PKU can't be find in Skylake-Server CPU
model in the code. So this patch will fix this issue in
Skylake-Server CPU model.
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <5014b57f834dcfa8fd3781504d98dcf063d54fde.1540801392.git.tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
New CPU models mostly inherit features from ancestor Skylake-Server,
while addin new features: AVX512_VNNI, Intel PT.
SSBD support for speculative execution
side channel mitigations.
Note:
On Cascadelake, some capabilities (RDCL_NO, IBRS_ALL, RSBA,
SKIP_L1DFL_VMENTRY and SSB_NO) are enumerated by MSR.
These features rely on MSR based feature support patch.
Will be added later after that patch's in.
http://lists.nongnu.org/archive/html/qemu-devel/2018-09/msg00074.html
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20180919031122.28487-2-tao3.xu@intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Note RSBA is specially treated -- no matter host support it or not, qemu
pretends it is supported.
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1539578845-37944-4-git-send-email-robert.hu@linux.intel.com>
[ehabkost: removed automatic enabling of RSBA]
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add kvm_get_supported_feature_msrs() to get supported MSR feature index list.
Add kvm_arch_get_supported_msr_feature() to get each MSR features value.
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1539578845-37944-2-git-send-email-robert.hu@linux.intel.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Remove a debugging hack which could be used to cause the
undocumented 'icebp' instruction to enable QEMU internal
debug logging. This code has always been #ifdeffed out
since it was introduced in commit aba9d61e34 in 2005;
judging by the rest of that commit (which is entirely
unrelated) it may have even been committed by accident.
(Note that WANT_ICEBP is not defined by default anyway.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20181009183314.13416-1-peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Intel SDM says for CPUID function 0DH, sub-function 0:
| • ECX enumerates the size (in bytes) required by the XSAVE instruction for an
| XSAVE area containing all the user state components supported by this
| processor.
| • EBX enumerates the size (in bytes) required by the XSAVE instruction for an
| XSAVE area containing all the user state components corresponding to bits
| currently set in XCR0.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Message-Id: <20180928104319.3296-1-bigeasy@linutronix.de>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
-----BEGIN PGP SIGNATURE-----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=kPZX
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/armbru/tags/pull-error-2018-10-22' into staging
Error reporting patches for 2018-10-22
# gpg: Signature made Mon 22 Oct 2018 13:20:23 BST
# gpg: using RSA key 3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-error-2018-10-22: (40 commits)
error: Drop bogus "use error_setg() instead" admonitions
vpc: Fail open on bad header checksum
block: Clean up bdrv_img_create()'s error reporting
vl: Simplify call of parse_name()
vl: Fix exit status for -drive format=help
blockdev: Convert drive_new() to Error
vl: Assert drive_new() does not fail in default_drive()
fsdev: Clean up error reporting in qemu_fsdev_add()
spice: Clean up error reporting in add_channel()
tpm: Clean up error reporting in tpm_init_tpmdev()
numa: Clean up error reporting in parse_numa()
vnc: Clean up error reporting in vnc_init_func()
ui: Convert vnc_display_init(), init_keyboard_layout() to Error
ui/keymaps: Fix handling of erroneous include files
vl: Clean up error reporting in device_init_func()
vl: Clean up error reporting in parse_fw_cfg()
vl: Clean up error reporting in mon_init_func()
vl: Clean up error reporting in machine_set_property()
vl: Clean up error reporting in chardev_init_func()
qom: Clean up error reporting in user_creatable_add_opts_foreach()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Calling error_report() in a function that takes an Error ** argument
is suspicious. Convert a few that are actually warnings to
warn_report().
While there, split a warning consisting of multiple sentences to
conform to conventions spelled out in warn_report()'s contract.
Cc: Alex Bennée <alex.bennee@linaro.org>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Fam Zheng <famz@redhat.com>
Cc: Wei Huang <wei@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20181017082702.5581-5-armbru@redhat.com>
When migrate_add_blocker failed, the invtsc_mig_blocker is not
appended so no need to remove. This can save several instructions.
Signed-off-by: Li Qiang <liq3ea@163.com>
Message-Id: <20181006091816.7659-1-liq3ea@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add handling of POST_MESSAGE hypercall. For that, add an interface to
regsiter a handler for the messages arrived from the guest on a
particular connection id (IOW set up a message connection in Hyper-V
speak).
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-10-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add handling of SIGNAL_EVENT hypercall. For that, provide an interface
to associate an EventNotifier with an event connection number, so that
it's signaled when the SIGNAL_EVENT hypercall with the matching
connection ID is called by the guest.
Support for using KVM functionality for this will be added in a followup
patch.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-8-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Per Hyper-V spec, SynIC message and event flag pages are to be
implemented as so called overlay pages. That is, they are owned by the
hypervisor and, when mapped into the guest physical address space,
overlay the guest physical pages such that
1) the overlaid guest page becomes invisible to the guest CPUs until the
overlay page is turned off
2) the contents of the overlay page is preserved when it's turned off
and back on, even at a different address; it's only zeroed at vcpu
reset
This particular nature of SynIC message and event flag pages is ignored
in the current code, and guest physical pages are used directly instead.
This happens to (mostly) work because the actual guests seem not to
depend on the features listed above.
This patch implements those pages as the spec mandates.
Since the extra RAM regions, which introduce migration incompatibility,
are only added at SynIC object creation which only happens when
hyperv_synic_kvm_only == false, no extra compat logic is necessary.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-5-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Certain configurations do not allow SynIC to be used in QEMU. In
particular,
- when hyperv_vpindex is off, SINT routes can't be used as they refer to
the destination vCPU by vp_index
- older KVM (which doesn't expose KVM_CAP_HYPERV_SYNIC2) zeroes out
SynIC message and event pages on every msr load, breaking migration
OTOH in-KVM users of SynIC -- SynIC timers -- do work in those
configurations, and we shouldn't stop the guest from using them.
To cover both scenarios, introduce an X86CPU property that makes CPU
init code to skip creation of the SynIC object (and thus disables any
SynIC use in QEMU) but keeps the KVM part of the SynIC working.
The property is clear by default but is set via compat logic for older
machine types.
As a result, when hv_synic and a modern machine type are specified, QEMU
will refuse to run unless vp_index is on and the kernel is recent
enough. OTOH with an older machine type QEMU will run fine with
hv_synic=on against an older kernel and/or without vp_index enabled but
will disallow the in-QEMU uses of SynIC (in e.g. VMBus).
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-4-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make Hyper-V SynIC a device which is attached as a child to a CPU. For
now it only makes SynIC visibile in the qom hierarchy, and maintains its
internal fields in sync with the respecitve msrs of the parent cpu (the
fields will be used in followup patches).
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-3-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Put a bit more consistency into handling KVM_CAP_HYPERV_SYNIC capability,
by checking its availability and determining the feasibility of hv-synic
property first, and enabling it later.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082217.29481-2-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This will allow to build slightly leaner QEMU that supports some HyperV
features of KVM (e.g. SynIC timers, PV spinlocks, APIC assists, etc.)
but nothing else on the QEMU side.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082041.29380-6-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A significant part of hyperv.c is not actually tied to x86, and can
be moved to hw/.
This will allow to maintain most of Hyper-V and VMBus
target-independent, and to avoid conflicts with inclusion of
arch-specific headers down the road in VMBus implementation.
Also this stuff can now be opt-out with CONFIG_HYPERV.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082041.29380-4-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Also make the inverse function, hyperv_find_vcpu, static as it's not
used outside hyperv.c
This paves the way to making hyperv.c built optionally.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082041.29380-3-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some parts of the Hyper-V hypervisor-guest interface appear to be
target-independent, so move them into a proper header.
Not that Hyper-V ARM64 emulation is around the corner but it seems more
conveninent to have most of Hyper-V and VMBus target-independent, and
allows to avoid conflicts with inclusion of arch-specific headers down
the road in VMBus implementation.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921082041.29380-2-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There's nothing kvm-specific in it so follow the suite and replace
"kvm_hv" prefix with "hyperv".
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921081836.29230-9-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Multiple entities (e.g. VMBus devices) can use the same SINT route. To
make their lives easier in maintaining SINT route ownership, make it
reference-counted. Adjust the respective API names accordingly.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921081836.29230-8-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use X86CPU pointer to refer to the respective HvSintRoute instead of
vp_index. This is more convenient and also paves the way for future
enhancements.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921081836.29230-7-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make sint ack callback accept an opaque pointer, that is stored on
sint_route at creation time.
This allows for more convenient interaction with the callback.
Besides, nothing outside hyperv.c should need to know the layout of
HvSintRoute fields any more so its declaration can be removed from the
header.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921081836.29230-6-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There's no point setting up an sint ack notifier if no callback is
specified.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921081836.29230-5-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180921081836.29230-4-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
accel_init_machine sets *(acc->allowed) to true if acc->init_machine(ms)
succeeds. There's no need to have both hvf_allowed and hvf_disabled.
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20181018143051.48508-1-r.bolshakov@yadro.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to Intel(R)64 and IA-32 Architectures Software Developer's
Manual, the following one-byte registers should be fetched when REX
prefix is present (sorted by reg encoding index):
AL, CL, DL, BL, SPL, BPL, SIL, DIL, R8L - R15L
The first 8 are fetched if REX.R is zero, the last 8 if non-zero.
The following registers should be fetched for instructions without REX
prefix (also sorted by reg encoding index):
AL, CL, DL, BL, AH, CH, DH, BH
Current emulation code doesn't handle accesses to SPL, BPL, SIL, DIL
when REX is present, thefore an instruction 40883e "mov %dil,(%rsi)" is
decoded as "mov %bh,(%rsi)".
That caused an infinite loop in vp_reset:
https://lists.gnu.org/archive/html/qemu-devel/2018-10/msg03293.html
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20181018134401.44471-1-r.bolshakov@yadro.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Hyper-V PV IPI support is merged to KVM, enable the feature in Qemu. When
enabled, this allows Windows guests to send IPIs to other vCPUs with a
single hypercall even when there are >64 vCPUs in the request.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20181009130853.6412-3-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The exception.pad field is going to be renamed to pending in an upcoming
header file update. Remove the unnecessary initialization; it was
introduced to please valgrind (commit 7e680753cf) but they were later
rendered unnecessary by commit 076796f8fd, which added the "= {}"
initializer to the declaration of "events". Therefore the patch does
not change behavior in any way.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This patch fixes the checking of boundary crossing instructions.
In icount mode only first instruction of the block may cross
the page boundary to keep the translation deterministic.
These conditions already existed, but compared the wrong variable.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Message-Id: <20180920071702.22477.43980.stgit@pasha-VirtualBox>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
While at it, also rename var to indicate it is not used only in KVM.
Reviewed-by: Nikita Leshchenko <nikita.leshchenko@oracle.com>
Reviewed-by: Patrick Colp <patrick.colp@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20180914003827.124570-2-liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This flag will be used for KVM's nested VMX migration; the HF_GUEST_MASK name
is already used in KVM, adopt it in QEMU as well.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Interrupt handling depends on various flags in env->hflags or env->hflags2,
and the exact detail were not exactly replicated between x86_cpu_has_work
and x86_cpu_exec_interrupt. Create a new function that extracts the
highest-priority non-masked interrupt, and use it in both functions.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
And convert it to a bool to use an existing hole
in the struct.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The AMD IOMMU does not (yet) support interrupt remapping. But
kvm_arch_fixup_msi_route assumes that all implementations do and crashes
when the AMD IOMMU is used in KVM mode.
Fixes: 8b5ed7dffa ("intel_iommu: add support for split irqchip")
Reported-by: Christopher Goldsworthy <christopher.goldsworthy@outlook.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-Id: <48ae78d8-58ec-8813-8680-6f407ea46041@siemens.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The capability macros are always defined, since they come from kernel
headers that are copied into the QEMU tree. Remove the unnecessary #ifdefs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The current implementation has three bugs,
* segment limits are not enforced in protected mode if the L bit is set
in the target segment descriptor
* segment limits are not enforced in compatibility mode (ljmp to 32-bit
code segment in long mode)
* #GP(new_cs) is generated rather than #GP(0)
Now the segment limits are enforced if we're not in long mode OR the
target code segment doesn't have the L bit set.
Signed-off-by: Andrew Oates <aoates@google.com>
Message-Id: <20180816011903.39816-1-andrew@andrewoates.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently call gates are always treated as 32-bit gates. In IA-32e mode
(either compatibility or 64-bit submode), system segment descriptors are
always 64-bit. Treating them as 32-bit has the expected unfortunate
effect: only the lower 32 bits of the offset are loaded, the stack
pointer is truncated, a bad new stack pointer is loaded from the TSS (if
switching privilege levels), etc.
This change adds support for 64-bit call gate to the lcall and ljmp
instructions. Additionally, there should be a check for non-canonical
stack pointers, but I've omitted that since there doesn't seem to be
checks for non-canonical addresses in this code elsewhere.
I've left the raise_exception_err_ra lines unwapped at 80 columns to
match the style in the rest of the file.
Signed-off-by: Andrew Oates <aoates@google.com>
Message-Id: <20180819181725.34098-1-andrew@andrewoates.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported by Coverity:
Error: RESOURCE_LEAK (CWE-772): [#def439]
qemu-2.12.0/target/i386/cpu.c:3179: alloc_fn: Storage is returned from allocation function "qdict_new".
qemu-2.12.0/qobject/qdict.c:34:5: alloc_fn: Storage is returned from allocation function "g_malloc0".
qemu-2.12.0/qobject/qdict.c:34:5: var_assign: Assigning: "qdict" = "g_malloc0(4120UL)".
qemu-2.12.0/qobject/qdict.c:37:5: return_alloc: Returning allocated memory "qdict".
qemu-2.12.0/target/i386/cpu.c:3179: var_assign: Assigning: "props" = storage returned from "qdict_new()".
qemu-2.12.0/target/i386/cpu.c:3217: leaked_storage: Variable "props" going out of scope leaks the storage it points to.
This was introduced by commit b8097deb35 ("i386: Improve
query-cpu-model-expansion full mode").
The leak is only theoretical: if ret->model->props is set to
props, the qapi_free_CpuModelExpansionInfo() call will free props
too in case of errors. The only way for this to not happen is if
we enter the default branch of the switch statement, which would
never happen because all CpuModelExpansionType values are being
handled.
It's still worth to change this to make the allocation logic
easier to follow and make the Coverity error go away. To make
everything simpler, initialize ret->model and ret->model->props
earlier in the function.
While at it, remove redundant check for !prop because prop is
always initialized at the beginning of the function.
Fixes: b8097deb35
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20180816183509.8231-1-ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Many of these are marked as "intentional/fix required" because they
just need adding a fall through comment. This is exactly what this
patch does, except for target/mips/translate.c where it is easier to
duplicate the code, and hw/audio/sb16.c where I consulted the DOSBox
sources and decide to just remove the LOG_UNIMP before the fallthrough.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Enabling TOPOEXT is always allowed, but it can't be enabled
blindly by "-cpu host" because it may make guests crash if the
rest of the cache topology information isn't provided or isn't
consistent.
This addresses the bug reported at:
https://bugzilla.redhat.com/show_bug.cgi?id=1613277
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20180809221852.15285-1-ehabkost@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
New CPU models mostly inherit features from ancestor Skylake, while addin new
features: UMIP, New Instructions ( PCONIFIG (server only), WBNOINVD,
AVX512_VBMI2, GFNI, AVX512_VNNI, VPCLMULQDQ, VAES, AVX512_BITALG),
Intel PT and 5-level paging (Server only). As well as
IA32_PRED_CMD, SSBD support for speculative execution
side channel mitigations.
Note:
For 5-level paging, Guest physical address width can be configured, with
parameter "phys-bits". Unless explicitly specified, we still use its default
value, even for Icelake-Server cpu model.
At present, hold on expose IA32_ARCH_CAPABILITIES to guest, as 1) This MSR
actually presents more than 1 'feature', maintainers are considering expanding current
features presentation of only CPUIDs to MSR bits; 2) a reasonable default value
for MSR_IA32_ARCH_CAPABILITIES needs to settled first. These 2 are actully
beyond Icelake CPU model itself but fundamental. So split these work apart
and do it later.
https://lists.gnu.org/archive/html/qemu-devel/2018-07/msg00774.htmlhttps://lists.gnu.org/archive/html/qemu-devel/2018-07/msg00796.html
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1530781798-183214-6-git-send-email-robert.hu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
WBNOINVD: Write back and do not invalidate cache, enumerated by
CPUID.(EAX=80000008H, ECX=0):EBX[bit 9].
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1530781798-183214-5-git-send-email-robert.hu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Support of IA32_PRED_CMD MSR already be enumerated by same CPUID bit as
SPEC_CTRL.
At present, mark CPUID_7_0_EDX_ARCH_CAPABILITIES unmigratable, per Paolo's
comment.
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1530781798-183214-3-git-send-email-robert.hu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
IA32_PRED_CMD MSR gives software a way to issue commands that affect the state
of indirect branch predictors. Enumerated by CPUID.(EAX=7H,ECX=0):EDX[26].
IA32_ARCH_CAPABILITIES MSR enumerates architectural features of RDCL_NO and
IBRS_ALL. Enumerated by CPUID.(EAX=07H, ECX=0):EDX[29].
https://software.intel.com/sites/default/files/managed/c5/63/336996-Speculative-Execution-Side-Channel-Mitigations.pdf
Signed-off-by: Robert Hoo <robert.hu@linux.intel.com>
Message-Id: <1530781798-183214-2-git-send-email-robert.hu@linux.intel.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
MSR_SMI_COUNT started being migrated in QEMU 2.12. Do not migrate it
on older machine types, or the subsection causes a load failure for
guests that use SMM.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Rename DCACHE to DATA_CACHE and ICACHE to INSTRUCTION_CACHE.
This avoids conflict with Linux asm/cachectl.h macros and fixes
build failure on mips hosts.
Reported-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20180717194010.30096-1-ehabkost@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Aleksandar Markovic <amarkovic@wavecomp.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Hyper-V identifies vCPUs by Virtual Processor (VP) index which can be
queried by the guest via HV_X64_MSR_VP_INDEX msr. It is defined by the
spec as a sequential number which can't exceed the maximum number of
vCPUs per VM.
It has to be owned by QEMU in order to preserve it across migration.
However, the initial implementation in KVM didn't allow to set this
msr, and KVM used its own notion of VP index. Fortunately, the way
vCPUs are created in QEMU/KVM makes it likely that the KVM value is
equal to QEMU cpu_index.
So choose cpu_index as the value for vp_index, and push that to KVM on
kernels that support setting the msr. On older ones that don't, query
the kernel value and assert that it's in sync with QEMU.
Besides, since handling errors from vCPU init at hotplug time is
impossible, disable vCPU hotplug.
This patch also introduces accessor functions to encapsulate the mapping
between a vCPU and its vp_index.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180702134156.13404-3-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In Hyper-V-related code, vCPUs are identified by their VP (virtual
processor) index. Since it's customary for "vcpu_id" in QEMU to mean
APIC id, rename the respective variables to "vp_index" to make the
distinction clear.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Message-Id: <20180702134156.13404-2-rkagan@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds field with content of KERNEL_GS_BASE MSR to QEMU note in
ELF dump.
On Windows, if all vCPUs are running usermode tasks at the time the dump is
created, this can be helpful in the discovery of guest system structures
during conversion ELF dump to MEMORY.DMP dump.
Signed-off-by: Viktor Prutyanov <viktor.prutyanov@virtuozzo.com>
Message-Id: <20180714123000.11326-1-viktor.prutyanov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since commit d6dcc5583e, '-cpu ?' shows the description of the
X86_CPU_TYPE_NAME("max") for the host CPU model:
Enables all features supported by the accelerator in the current host
instead of the expected:
KVM processor with all supported host features
or
HVF processor with all supported host features
This is caused by the early use of kvm_enabled() and hvf_enabled() in
a class_init function. Since the accelerator isn't configured yet, both
helpers return false unconditionally.
A QEMU binary will only be compiled with one of these accelerators, not
both. The appropriate description can thus be decided at build time.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <153055056654.212317.4697363278304826913.stgit@bahia.lan>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Correct the output of the "info mem" and "info tlb" monitor commands to
correctly show canonical addresses.
In 48-bit addressing mode, the upper 16 bits of linear addresses are
equal to bit 47. In 57-bit addressing mode (LA57), the upper 7 bits of
linear addresses are equal to bit 56.
Signed-off-by: Doug Gale <doug16k@gmail.com>
Message-Id: <20180617084025.29198-1-doug16k@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This implements NPT suport for SVM by hooking into
x86_cpu_handle_mmu_fault where it reads the stage-1 page table. Whether
we need to perform this 2nd stage translation, and how, is decided
during vmrun and stored in hflags2, along with nested_cr3 and
nested_pg_mode.
As get_hphys performs a direct cpu_vmexit in case of NPT faults, we need
retaddr in that function. To avoid changing the signature of
cpu_handle_mmu_fault, this passes the value from tlb_fill to get_hphys
via the CPU state.
This was tested successfully via the Jailhouse hypervisor.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-Id: <567473a0-6005-5843-4c73-951f476085ca@web.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add support for Hyper-V TLB flush which recently got added to KVM.
Just like regular Hyper-V we announce HV_EX_PROCESSOR_MASKS_RECOMMENDED
regardless of how many vCPUs we have. Windows is 'smart' and uses less
expensive non-EX Hypercall whenever possible (when it wants to flush TLB
for all vCPUs or the maximum vCPU index in the vCPU set requires flushing
is less than 64).
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20180610184927.19309-1-vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When guest CPU PM is enabled, and with -cpu host, expose the host CPU
MWAIT leaf in the CPUID so guest can make good PM decisions.
Note: the result is 100% CPU utilization reported by host as host
no longer knows that the CPU is halted.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20180622192148.178309-3-mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With this flag, kvm allows guest to control host CPU power state. This
increases latency for other processes using same host CPU in an
unpredictable way, but if decreases idle entry/exit times for the
running VCPU, so to use it QEMU needs a hint about whether host CPU is
overcommitted, hence the flag name.
Follow-up patches will expose this capability to guest
(using mwait leaf).
Based on a patch by Wanpeng Li <kernellwp@gmail.com> .
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20180622192148.178309-2-mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's start to use "info pic" just like other platforms. For now we
keep the command for a while so that old users can know what is the new
command to use.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20171229073104.3810-6-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It calls cpu_loop_exit in system emulation mode (and should never be
called in user emulation mode).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-Id: <6f4d44ffde55d074cbceb48309c1678600abad2f.1522769774.git.jan.kiszka@web.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We need to terminate the translation block after STGI so that pending
interrupts can be injected.
This fixes pending NMI injection for Jailhouse which uses "stgi; clgi"
to open a brief injection window.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-Id: <37939b244dda0e9cccf96ce50f2b15df1e48315d.1522769774.git.jan.kiszka@web.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Check for SVM interception prior to injecting an NMI. Tested via the
Jailhouse hypervisor.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Message-Id: <c65877e9a011ee4962931287e59f502c482b8d0b.1522769774.git.jan.kiszka@web.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some variations of Linux kernels end up accessing MSR's that the Windows
Hypervisor doesn't implement which causes a GP to be returned to the guest.
This fix registers QEMU for unimplemented MSR access and globally returns 0 on
reads and ignores writes. This behavior is allows the Linux kernel to probe the
MSR with a write/read/check sequence it does often without failing the access.
Signed-off-by: Justin Terry (VM) <juterry@microsoft.com>
Message-Id: <20180605221500.21674-2-juterry@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Adds a workaround to an incorrect value setting
CPUID Fn8000_0001_ECX[bit 9 OSVW] = 1. This can cause a guest linux kernel
to panic when an issue to rdmsr C001_0140h returns 0. Disabling this feature
correctly allows the guest to boot without accessing the osv workarounds.
Signed-off-by: Justin Terry (VM) <juterry@microsoft.com>
Message-Id: <20180605221500.21674-1-juterry@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The implementation of these two instructions was swapped.
At the same time, unify the setup of eflags for the insn group.
Reported-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <20170712192902.15493-1-rth@twiddle.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Determining the size of a field is useful when you don't have a struct
variable handy. Open-coding this is ugly.
This patch adds the sizeof_field() macro, which is similar to
typeof_field(). Existing instances are updated to use the macro.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20180614164431.29305-1-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Remove generic non-intel check while validating hyperthreading support.
Certain AMD CPUs can support hyperthreading now.
CPU family with TOPOEXT feature can support hyperthreading now.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1529443919-67509-4-git-send-email-babu.moger@amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Enable TOPOEXT feature on EPYC CPU. This is required to support
hyperthreading on VM guests. Also extend xlevel to 0x8000001E.
Disable topoext on PC_COMPAT_2_12 and keep xlevel 0x8000000a.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Message-Id: <1529443919-67509-3-git-send-email-babu.moger@amd.com>
[ehabkost: Added EPYC-IBPB.xlevel to PC_COMPAT_2_12]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This is part of topoext support. To keep the compatibility, it is better
we support all the combination of nr_cores and nr_threads currently
supported. By allowing more nr_cores and nr_threads, we might end up with
more nodes than we can actually support with the real hardware. We need to
fix up the node id to make this work. We can achieve this by shifting the
socket_id bits left to address more nodes.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Message-Id: <1529443919-67509-2-git-send-email-babu.moger@amd.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Enabling TOPOEXT feature might cause compatibility issues if
older kernels does not set this feature. Lets set this feature
unconditionally.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Message-Id: <1528939107-17193-2-git-send-email-babu.moger@amd.com>
[ehabkost: rewrite comment and commit message]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
AMD future CPUs expose a mechanism to tell the guest that the
Speculative Store Bypass Disable is not needed and that the
CPU is all good.
This is exposed via the CPUID 8000_0008.EBX[26] bit.
See 124441_AMD64_SpeculativeStoreBypassDisable_Whitepaper_final.pdf
A copy of this document is available at
https://bugzilla.kernel.org/show_bug.cgi?id=199889
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Message-Id: <20180601153809.15259-3-konrad.wilk@oracle.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
AMD future CPUs expose _two_ ways to utilize the Intel equivalant
of the Speculative Store Bypass Disable. The first is via
the virtualized VIRT_SPEC CTRL MSR (0xC001_011f) and the second
is via the SPEC_CTRL MSR (0x48). The document titled:
124441_AMD64_SpeculativeStoreBypassDisable_Whitepaper_final.pdf
gives priority of SPEC CTRL MSR over the VIRT SPEC CTRL MSR.
A copy of this document is available at
https://bugzilla.kernel.org/show_bug.cgi?id=199889
Anyhow, this means that on future AMD CPUs there will be _two_ ways to
deal with SSBD.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Message-Id: <20180601153809.15259-2-konrad.wilk@oracle.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
OSPKE is not a static feature flag: it changes dynamically at
runtime depending on CR4, and it was never configurable: KVM
never returned OSPKE on GET_SUPPORTED_CPUID, and on TCG enables
it automatically if CR4_PKE_MASK is set.
Remove OSPKE from the feature name array so users don't try to
configure it manually.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20180611203712.12086-1-ehabkost@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
OSXAVE is not a static feature flag: it changes dynamically at
runtime depending on CR4, and it was never configurable: KVM
never returned OSXSAVE on GET_SUPPORTED_CPUID, and it is not
included in TCG_EXT_FEATURES.
Remove OSXSAVE from the feature name array so users don't try to
configure it manually.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20180611203855.13269-1-ehabkost@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
When using '-cpu help' the list of CPUID features is grouped according
to the internal low level CPUID grouping. The data printed results in
very long lines too.
This combines to make it hard for users to read the output and identify
if QEMU knows about the feature they wish to use.
This change gets rid of the grouping of features and treats all flags as
single list. The list is sorted into alphabetical order and the printing
with line wrapping at the 77th column.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20180606165527.17365-4-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The current list of CPU model names output by "-cpu help" is sorted
alphabetically based on the internal QOM class name. The text that is
displayed, however, uses the CPU model name, which is equivalent to the
QOM class name, minus a suffix. Unfortunately that suffix has an effect
on the sort ordering, for example, causing the various Broadwell
variants to appear reversed:
x86 486
x86 Broadwell-IBRS Intel Core Processor (Broadwell, IBRS)
x86 Broadwell-noTSX-IBRS Intel Core Processor (Broadwell, no TSX, IBRS
x86 Broadwell-noTSX Intel Core Processor (Broadwell, no TSX)
x86 Broadwell Intel Core Processor (Broadwell)
x86 Conroe Intel Celeron_4x0 (Conroe/Merom Class Core 2)
By sorting on the actual CPU model name text that is displayed, the
result is
x86 486
x86 Broadwell Intel Core Processor (Broadwell)
x86 Broadwell-IBRS Intel Core Processor (Broadwell, IBRS)
x86 Broadwell-noTSX Intel Core Processor (Broadwell, no TSX)
x86 Broadwell-noTSX-IBRS Intel Core Processor (Broadwell, no TSX, IBRS)
x86 Conroe Intel Celeron_4x0 (Conroe/Merom Class Core 2)
This requires extra string allocations during sorting, but this is not a
concern given the usage scenario and the number of CPU models that exist.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20180606165527.17365-3-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Since the addition of the -IBRS CPU model variants, the descriptions
shown by '-cpu help' are not well aligned, as several model names
overflow the space allowed. Right aligning the CPU model names is also
not attractive, because it obscures the common name prefixes of many
models. The CPU model name field needs to be 4 characters larger, and
be left aligned instead.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20180606165527.17365-2-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add support for cpuid leaf CPUID_8000_001E. Build the config that closely
match the underlying hardware. Please refer to the Processor Programming
Reference (PPR) for AMD Family 17h Model for more details.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Message-Id: <1528498581-131037-2-git-send-email-babu.moger@amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add information for cpuid 0x8000001D leaf. Populate cache topology information
for different cache types (Data Cache, Instruction Cache, L2 and L3) supported
by 0x8000001D leaf. Please refer to the Processor Programming Reference (PPR)
for AMD Family 17h Model for more details.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Message-Id: <1527176614-26271-3-git-send-email-babu.moger@amd.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Always initialize CPUCaches structs with cache information, even
if legacy_cache=true. Use different CPUCaches struct for
CPUID[2], CPUID[4], and the AMD CPUID leaves.
This will simplify a lot the logic inside cpu_x86_cpuid().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Babu Moger <babu.moger@amd.com>
Message-Id: <1527176614-26271-2-git-send-email-babu.moger@amd.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Do the cast to uintptr_t within the helper, so that the compiler
can type check the pointer argument. We can also do some more
sanity checking of the index argument.
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Now we've updated our copy of the kernel headers we can remove the
compatibility shim that handled KVM_HINTS_REALTIME not being defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180525132755.21839-7-peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In kernel header commit 633711e8287, the define KVM_HINTS_DEDICATED
was renamed to KVM_HINTS_REALTIME. Work around this compatibility
break by (a) using the new constant name, and (b) defining it
if the headers don't.
Part (b) can be removed once we've updated our copy of the kernel
headers to a version that defines KVM_HINTS_REALTIME.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180525132755.21839-5-peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch fixes a few compiler warnings, especially in case of
x86 targets, where the number of registers was not properly handled
and could cause an overflow.
Signed-off-by: Alessandro Pilotti <apilotti@cloudbasesolutions.com>
Signed-off-by: Justin Terry (VM) <juterry@microsoft.com>
Signed-off-by: Lucian Petrut <lpetrut@cloudbasesolutions.com>
Message-Id: <1526405722-10887-3-git-send-email-lpetrut@cloudbasesolutions.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We're currently linking against import libraries of the WHP DLLs.
By dynamically loading the libraries, we ensure that QEMU will work
on previous Windows versions, where the WHP DLLs will be missing
(assuming that WHP is not requested).
Also, we're simplifying the build process, as we no longer require
the import libraries.
Signed-off-by: Alessandro Pilotti <apilotti@cloudbasesolutions.com>
Signed-off-by: Justin Terry (VM) <juterry@microsoft.com>
Signed-off-by: Lucian Petrut <lpetrut@cloudbasesolutions.com>
Message-Id: <1526405722-10887-2-git-send-email-lpetrut@cloudbasesolutions.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Switch to the header we imported from Linux,
this allows us to drop a hack in kvm_i386.h.
More code will be dropped in the next patch.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
AMD Zen expose the Intel equivalant to Speculative Store Bypass Disable
via the 0x80000008_EBX[25] CPUID feature bit.
This needs to be exposed to guest OS to allow them to protect
against CVE-2018-3639.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20180521215424.13520-3-berrange@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
