The checking against reg16_inoutportreg can be had with a simple test of
a bit, and the value setting from inoutportreg can be replaced by using
the actual register's reg_type field.
Note that the so far redundant 2nd instance of OPERAND_TYPE_INOUTPORTREG
is left in place, for its use in type_names[].
The check_prefix label was bogus from the beginning: The special
checking is supposed to happen for PadLock insns only; no
3-opcode-byte insn should go this path.
The previous constraints were based on information already in opcodes and it
seems that a few of them were wrong. I have now hand verified the ones changed
by the previous patch and corrected where needed.
This prevents a warning to be issued when one shouldn't be.
opcodes/
PR binutils/23369
* aarch64-opc.c (aarch64_sys_regs): Make read/write csselr_el1,
vsesr_el2, osdtrrx_el1, osdtrtx_el1, pmsidr_el1.
gas/testsuite/
PR binutils/23369
* gas/aarch64/msr.d (csselr_el1,
vsesr_el2, osdtrrx_el1, osdtrtx_el1, pmsidr_el1): New.
* gas/aarch64/msr.s: Likewise.
In the microMIPS mode also accept %half, %got, %call, %got_hi, %got_lo,
%call_hi, %call_lo, %neg, %got_page, %highest, %got_disp, %tlsgd,
%tlsldm, %dtprel_hi, %dtprel_lo, %gottprel, %tprel_hi and %tprel_lo
percent-ops with macros, so that they can be used with instructions that
expand into sequences if relocation is required due to their limited
offset span, such as LL, LWL, etc., fixing GAS assertions:
.../gas/testsuite/gas/mips/elf-rel28.s: Assembler messages:
.../gas/testsuite/gas/mips/elf-rel28.s:17: Internal error in macro_build at .../gas/config/tc-mips.c:8854.
Please report this bug.
observed if an attempt is made to assemble the `elf-rel28.s' test case
modified to use one of the affected instructions to microMIPS code.
gas/
* config/tc-mips.c (macro_build) <'i', 'j'>: Also accept
BFD_RELOC_16, BFD_RELOC_MIPS_GOT16, BFD_RELOC_MIPS_CALL16,
BFD_RELOC_MIPS_GOT_HI16, BFD_RELOC_MIPS_GOT_LO16,
BFD_RELOC_MIPS_CALL_HI16, BFD_RELOC_MIPS_CALL_LO16,
BFD_RELOC_MIPS_SUB, BFD_RELOC_MIPS_GOT_PAGE,
BFD_RELOC_MIPS_HIGHEST, BFD_RELOC_MIPS_GOT_DISP,
BFD_RELOC_MIPS_TLS_GD, BFD_RELOC_MIPS_TLS_LDM,
BFD_RELOC_MIPS_TLS_DTPREL_HI16, BFD_RELOC_MIPS_TLS_DTPREL_LO16,
BFD_RELOC_MIPS_TLS_GOTTPREL, BFD_RELOC_MIPS_TLS_TPREL_HI16 and
BFD_RELOC_MIPS_TLS_TPREL_LO16 relocations if in the microMIPS
mode.
* testsuite/gas/mips/elf-rel28-lldscd-n32.d: New test.
* testsuite/gas/mips/elf-rel28-lldscd-micromips-n32.d: New test.
* testsuite/gas/mips/elf-rel28-lldscd-n64.d: New test.
* testsuite/gas/mips/elf-rel28-lldscd-micromips-n64.d: New test.
* testsuite/gas/mips/elf-rel28.s: Add instruction selection.
* testsuite/gas/mips/mips.exp: Run the new tests.
Complement commit df58fc944d ("MIPS: microMIPS ASE support"),
<https://sourceware.org/ml/binutils/2011-07/msg00198.html>, and add TLS
and a few miscellaneous relocations to NewABI microMIPS support, fixing
GAS assertion failures:
.../gas/testsuite/gas/mips/elf-rel28.s: Assembler messages:
.../gas/testsuite/gas/mips/elf-rel28.s:19: Internal error in append_insn at .../gas/config/tc-mips.c:7660.
Please report this bug.
observed if an attempt is made to assemble the `elf-rel28.s' test case
to microMIPS code. The relocations are the same as with o32 support,
except for `partial_inplace' and `src_mask' updates for the respective
RELA variants.
bfd/
* elf64-mips.c (micromips_elf64_howto_table_rel): Add
R_MICROMIPS_HI0_LO16, R_MICROMIPS_TLS_GD, R_MICROMIPS_TLS_LDM,
R_MICROMIPS_TLS_DTPREL_HI16, R_MICROMIPS_TLS_DTPREL_LO16,
R_MICROMIPS_TLS_GOTTPREL, R_MICROMIPS_TLS_TPREL_HI16,
R_MICROMIPS_TLS_TPREL_LO16, R_MICROMIPS_GPREL7_S2 and
R_MICROMIPS_PC23_S2 relocation entries.
(micromips_elf64_howto_table_rela): Likewise.
(micromips_reloc_map): Likewise.
* elfn32-mips.c (elf_micromips_howto_table_rel): Likewise.
(elf_micromips_howto_table_rela): Likewise.
(micromips_reloc_map): Likewise.
gas/
* testsuite/gas/mips/elf-rel28-micromips-n32.d: New test.
* testsuite/gas/mips/elf-rel28-micromips-n64.d: New test.
* testsuite/gas/mips/mips.exp: Run the new tests.
BFD's bfd_get_mach () function returns a bfd specific value representing
the architecture of the target which is populated from the Tag_CPU_arch
build attribute value of that target. Among other users of that
interfacem, objdump which uses it to print the architecture version of
the binary being examinated and to decide what instruction is available
if run with "-m arm" via its own mapping from bfd_mach_arm_X values to
feature bits available.
However, both BFD and objdump's most recent known architecture is
Armv5TE. When encountering a newer architecture bfd_get_mach will return
bfd_mach_arm_unknown. This is unfortunate since objdump uses that value
to allow all instructions on all architectures which is already what it
does by default, making the "-m arm" trick useless.
This patch updates BFD and objdump's knowledge of Arm architecture
versions up to the latest Armv8-M Baseline and Mainline, Armv8-R and
Armv8.4-A architectures. Since several architecture versions (eg. 8.X-A)
share the same Tag_CPU_arch build attribute value and
bfd_mach_arm values, the mapping from bfd machine value to feature bits
need to return the most featureful feature bits that would yield the
given bfd machine value otherwise some instruction would not disassemble
under "-m arm" mode. The patch rework that mapping to make this clearer
and simplify writing the mapping rules. In particular, for simplicity
all FPU instructions are allowed in all cases.
Finally, the patch also rewrite the cpu_arch_ver table in GAS to use the
TAG_CPU_ARCH_X macros rather than hardcode their value.
2018-07-02 Thomas Preud'homme <thomas.preudhomme@arm.com>
bfd/
* archures.c (bfd_mach_arm_5TEJ, bfd_mach_arm_6, bfd_mach_arm_6KZ,
bfd_mach_arm_6T2, bfd_mach_arm_6K, bfd_mach_arm_7, bfd_mach_arm_6M,
bfd_mach_arm_6SM, bfd_mach_arm_7EM, bfd_mach_arm_8, bfd_mach_arm_8R,
bfd_mach_arm_8M_BASE, bfd_mach_arm_8M_MAIN): Define.
* bfd-in2.h: Regenerate.
* cpu-arm.c (arch_info_struct): Add entries for above new
bfd_mach_arm values.
* elf32-arm.c (bfd_arm_get_mach_from_attributes): Add Tag_CPU_arch to
bfd_mach_arm mapping logic for pre Armv4 and Armv5TEJ and later
architectures. Force assert failure for any new Tag_CPU_arch value.
gas/
* config/tc-arm.c (cpu_arch_ver): Use symbolic TAG_CPU_ARCH macros
rather than hardcode their values.
ld/
* arm-dis.c (select_arm_features): Fix typo in heading comment. Allow
all FPU features and add mapping from new bfd_mach_arm values to
allowed CPU feature bits.
opcodes/
* testsuite/ld-arm/tls-descrelax-be8.d: Add architecture version in
expected result.
* testsuite/ld-arm/tls-descrelax-v7.d: Likewise.
* testsuite/ld-arm/tls-longplt-lib.d: Likewise.
* testsuite/ld-arm/tls-longplt.d: Likewise.
Binutils documentation uses a mix of spelling for the compound word
"command-line X". According to [1]:
"Sometimes compound words are written separately (nail polish),
sometimes with a hyphen (short-sighted) and sometimes as one word
(eyelashes). Often new compounds are written as two separate words and,
as they become more familiar, they are either connected with a hyphen
(-) or made into one word."
I think command-line X is common enough in our industry that the two
workds command and line should be connected. Since command-line is more
common than commandline, I propose to update binutils documentation to
consistently use "command-line" when this is used as an adjective to a
noun (eg. command-line argument, command-line switch, command-line
option and command-line flag). I've left occurences of "the command
line" as is. I've also left gdb, sim and readline alone and have only
touched public documentation (texi and NEWS files).
[1]
http://dictionary.cambridge.org/grammar/british-grammar/word-formation/compounds
2018-07-02 Thomas Preud'homme <thomas.preudhomme@arm.com>
bfd/
* doc/bfdint.texi: Use command-line consistently when used in a
compount word.
* doc/bfdsumm.texi: Likewise.
binutils/
* NEWS: Use command-line consistently when used in a compount word.
* doc/binutils.texi: Likewise and fix trailing whitespace on same
line.
gas/
* NEWS: Use command-line consistently when used in a compount word.
* doc/as.texi: Likewise.
* doc/c-aarch64.texi: Likewise.
* doc/c-alpha.texi: Likewise.
* doc/c-arc.texi: Likewise.
* doc/c-arm.texi: Likewise.
* doc/c-avr.texi: Likewise.
* doc/c-bfin.texi: Likewise.
* doc/c-cris.texi: Likewise.
* doc/c-epiphany.texi: Likewise.
* doc/c-i386.texi: Likewise.
* doc/c-ia64.texi: Likewise.
* doc/c-lm32.texi: Likewise.
* doc/c-m32r.texi: Likewise.
* doc/c-m68k.texi: Likewise.
* doc/c-mips.texi: Likewise.
* doc/c-mmix.texi: Likewise.
* doc/c-msp430.texi: Likewise.
* doc/c-mt.texi: Likewise.
* doc/c-nios2.texi: Likewise.
* doc/c-ppc.texi: Likewise.
* doc/c-pru.texi: Likewise.
* doc/c-rl78.texi: Likewise.
* doc/c-rx.texi: Likewise.
* doc/c-tic6x.texi: Likewise.
* doc/c-v850.texi: Likewise.
* doc/c-vax.texi: Likewise.
* doc/c-visium.texi: Likewise.
* doc/c-xstormy16.texi: Likewise.
* doc/c-xtensa.texi: Likewise.
* doc/c-z80.texi: Likewise.
* doc/c-z8k.texi: Likewise.
* doc/internals.texi: Likewise.
gprof/
* gprof.texi: Use command-line consistently when used in a compount
word.
ld/
* NEWS: Use command-line consistently when used in a compount word.
* ld.texinfo: Likewise.
* ldint.texinfo: Likewise.
A recent case in golang highlighted that gas wasn't warning on these
unpredictable cases in the architecture. Fixed thusly.
I need to audit gcc to make sure we have early clobbers on the
patterns but that's a separate patch.
Tested aarch64-none-elf and gas
Ok ?
Ramana
2018-06-29 Ramana Radhakrishnan <ramana.radhakrishnan@arm.com>
* config/tc-aarch64.c (warn_unpredictable_ldst): Add
unpredictable cases for ldxp, stlxrb, stlxrh, stlxr. *
testsuite/gas/aarch64/diagnostic.s: New tests. *
testsuite/gas/aarch64/diagnostic.l: Adjust.
Some instructions in Armv8-a place a limitation on FP16 registers that can be
used as the register from which to select an element from.
e.g. fmla restricts Rm to 4 bits when using an FP16 register. This restriction
does not apply for all instructions, e.g. fcmla does not have this restriction
as it gets an extra bit from the M field.
Unfortunately, this restriction to S_H was added for all _Em operands before,
meaning for a large number of instructions you couldn't use the full register
file.
This fixes the issue by introducing a new operand _Em16 which applies this
restriction only when paired with S_H and leaves the _Em and the other
qualifiers for _Em16 unbounded (i.e. using the full 5 bit range).
Also the patch updates all instructions that should be affected by this.
opcodes/
PR binutils/23192
* aarch64-asm-2.c: Regenerate.
* aarch64-dis-2.c: Likewise.
* aarch64-opc-2.c: Likewise.
* aarch64-dis.c (aarch64_ext_reglane): Add AARCH64_OPND_Em16 constraint.
* aarch64-opc.c (operand_general_constraint_met_p,
aarch64_print_operand): Likewise.
* aarch64-tbl.h (aarch64_opcode_table): Change Em to Em16 for smlal,
smlal2, fmla, fmls, fmul, fmulx, sqrdmlah, sqrdlsh, fmlal, fmlsl,
fmlal2, fmlsl2.
(AARCH64_OPERANDS): Add Em2.
gas/
PR binutils/23192
* config/tc-aarch64.c (process_omitted_operand, parse_operands): Add
AARCH64_OPND_Em16
* testsuite/gas/aarch64/advsimd-armv8_3.s: Expand tests to cover upper
16 registers.
* testsuite/gas/aarch64/advsimd-armv8_3.d: Likewise.
* testsuite/gas/aarch64/advsimd-compnum.s: Likewise.
* testsuite/gas/aarch64/advsimd-compnum.d: Likewise.
* testsuite/gas/aarch64/sve.d: Likewise.
include/
PR binutils/23192
*opcode/aarch64.h (aarch64_opnd): Add AARCH64_OPND_Em16.
With the update to newer autotools, some gas object files are now
built in config/, breaking xtensa-elf and ia64-vms. This patch fixes
the dependencies.
* configure.ac: Specify extra_objects with leading "config/"
for xtensa-relax.o and te-vms.o. Use case statements to unique
extra_objects. Formatting.
* configure: Regenerate.
PR 23335
* config/tc-msp430.c (check_reg): Only accept register name
strings that do not end in an alphanumeric character.
* testsuite/gas/msp430/msp430x.d: Update expected disassembly.
This patch fixes a disassembly issue with the aliases to subs with a shifted
register. The subs instruction with the zero register as destination is
supposed to alias to cmp and when the first input register is the zero register
the subs is supposed to be aliased to negs.
This means that a subs with destination and first input registers the zero
register is supposed to be a cmp.
This is done by raising the priority of the cmp alias.
opcodes/
* aarch64-tbl.h (aarch64_opcode_table): Fix alias flag for negs
* aarch64-asm-2.c: Regenerate.
* aarch64-dis-2.c: Likewise.
gas/
* testsuite/gas/aarch64/addsub.s: Add negs to zero reg test.
* testsuite/gas/aarch64/addsub.d: Likewise.
Also make the automake strictness "foreign". My regeneration of the
three doc/Makefile.in files already had --foreign in the automake
invocation, so this just makes it explicit.
bfd/
* doc/Makefile.am (AUTOMAKE_OPTIONS): Add "foreign".
* doc/Makefile.in: Regenerate.
binutils/
* doc/Makefile.am (AUTOMAKE_OPTIONS): Add "foreign".
* doc/Makefile.in: Regenerate.
gas/
* doc/Makefile.am (AUTOMAKE_OPTIONS): Add "foreign".
* doc/Makefile.in: Regenerate.
zlib/
* Makefile.in: Regenerate.
For more information see the email thread starting here:
https://www.sourceware.org/ml/binutils/2018-05/msg00348.html
PR 21458
* tc-arm.c (do_adr): Only set the bottom bit of an imported thumb
function symbol address if -mthumb-interwork is active.
(do_adrl): Likewise.
* doc/c-arm.texi: Update descriptions of the -mthumb-interwork
option and the ADR and ADRL pseudo-ops.
* NEWS: Mention the new behaviour of the ADR and ADRL pseudo-ops.
* testsuite/gas/arm/pr21458.d: Add -mthumb-interwork option to
assembler command line.
* testsuite/gas/arm/adr.d: Likewise.
* testsuite/gas/arm/adrl.d: Likewise.
When trying to run the update-gnulib.sh script in gdb, I get this:
Error: Wrong automake version (Unescaped left brace in regex is deprecated, passed through in regex; marked by <-- HERE in m/\${ <-- HERE ([^ =:+{}]+)}/ at /opt/automake/1.11.1/bin/automake line 4113.), we need 1.11.1.
Aborting.
Apparently, it's an issue with a regex in automake that triggers a
warning starting with Perl 5.22. It has been fixed in automake 1.15.1.
So I think it's a good excuse to bump the versions of autoconf and
automake used in the gnulib import. And to avoid requiring multiple
builds of autoconf/automake, it was suggested that we bump the required
version of those tools for all binutils-gdb.
For autoconf, the 2.69 version is universally available, so it's an easy
choice. For automake, different distros and distro versions have
different automake versions. But 1.15.1 seems to be the most readily
available as a package. In any case, it's easy to build it from source.
I removed the version checks from AUTOMAKE_OPTIONS and AC_PREREQ,
because I don't think they are useful in our case. They only specify a
lower bound for the acceptable version of automake/autoconf. That's
useful if you let the user choose the version of the tool they want to
use, but want to set a minimum version (because you use a feature that
was introduced in that version). In our case, we force people to use a
specific version anyway. For the autoconf version, we have the check in
config/override.m4 that enforces the version we want. It will be one
less thing to update next time we change autotools version.
I hit a few categories of problems that required some changes. They are
described below along with the chosen solutions.
Problem 1:
configure.ac:17: warning: AM_INIT_AUTOMAKE: two- and three-arguments forms are deprecated. For more info, see:
configure.ac:17: http://www.gnu.org/software/automake/manual/automake.html#Modernize-AM_005fINIT_005fAUTOMAKE-invocation
Solution 1:
Adjust the code based on the example at that URL.
Problem 2 (in zlib/):
Makefile.am: error: required file './INSTALL' not found
Makefile.am: 'automake --add-missing' can install 'INSTALL'
Makefile.am: error: required file './NEWS' not found
Makefile.am: error: required file './AUTHORS' not found
Makefile.am: error: required file './COPYING' not found
Makefile.am: 'automake --add-missing' can install 'COPYING'
Solution 2:
Add the foreign option to AUTOMAKE_OPTIONS.
Problem 3:
doc/Makefile.am:20: error: support for Cygnus-style trees has been removed
Solution 3:
Remove the cygnus options.
Problem 4:
Makefile.am:656: warning: 'INCLUDES' is the old name for 'AM_CPPFLAGS' (or '*_CPPFLAGS')
Solution 4:
Rename "INCLUDES = " to "AM_CPPFLAGS += " (because AM_CPPFLAGS is
already defined earlier).
Problem 5:
doc/Makefile.am:71: warning: suffix '.texinfo' for Texinfo files is discouraged; use '.texi' instead
doc/Makefile.am: warning: Oops!
doc/Makefile.am: It appears this file (or files included by it) are triggering
doc/Makefile.am: an undocumented, soon-to-be-removed automake hack.
doc/Makefile.am: Future automake versions will no longer place in the builddir
doc/Makefile.am: (rather than in the srcdir) the generated '.info' files that
doc/Makefile.am: appear to be cleaned, by e.g. being listed in CLEANFILES or
doc/Makefile.am: DISTCLEANFILES.
doc/Makefile.am: If you want your '.info' files to be placed in the builddir
doc/Makefile.am: rather than in the srcdir, you have to use the shiny new
doc/Makefile.am: 'info-in-builddir' automake option.
Solution 5:
Rename .texinfo files to .texi.
Problem 6:
doc/Makefile.am: warning: Oops!
doc/Makefile.am: It appears this file (or files included by it) are triggering
doc/Makefile.am: an undocumented, soon-to-be-removed automake hack.
doc/Makefile.am: Future automake versions will no longer place in the builddir
doc/Makefile.am: (rather than in the srcdir) the generated '.info' files that
doc/Makefile.am: appear to be cleaned, by e.g. being listed in CLEANFILES or
doc/Makefile.am: DISTCLEANFILES.
doc/Makefile.am: If you want your '.info' files to be placed in the builddir
doc/Makefile.am: rather than in the srcdir, you have to use the shiny new
doc/Makefile.am: 'info-in-builddir' automake option.
Solution 6:
Remove the hack at the bottom of doc/Makefile.am and use
the info-in-builddir automake option.
Problem 7:
doc/Makefile.am:35: error: required file '../texinfo.tex' not found
doc/Makefile.am:35: 'automake --add-missing' can install 'texinfo.tex'
Solution 7:
Use the no-texinfo.tex automake option. We also have one in
texinfo/texinfo.tex, not sure if we should point to that, or move it
(or a newer version of it added with automake --add-missing) to
top-level.
Problem 8:
Makefile.am:131: warning: source file 'config/tc-aarch64.c' is in a subdirectory,
Makefile.am:131: but option 'subdir-objects' is disabled
automake: warning: possible forward-incompatibility.
automake: At least a source file is in a subdirectory, but the 'subdir-objects'
automake: automake option hasn't been enabled. For now, the corresponding output
automake: object file(s) will be placed in the top-level directory. However,
automake: this behaviour will change in future Automake versions: they will
automake: unconditionally cause object files to be placed in the same subdirectory
automake: of the corresponding sources.
automake: You are advised to start using 'subdir-objects' option throughout your
automake: project, to avoid future incompatibilities.
Solution 8:
Use subdir-objects, that means adjusting references to some .o that will now
be in config/.
Problem 9:
configure.ac:375: warning: AC_LANG_CONFTEST: no AC_LANG_SOURCE call detected in body
../../lib/autoconf/lang.m4:193: AC_LANG_CONFTEST is expanded from...
../../lib/autoconf/general.m4:2601: _AC_COMPILE_IFELSE is expanded from...
../../lib/autoconf/general.m4:2617: AC_COMPILE_IFELSE is expanded from...
../../lib/m4sugar/m4sh.m4:639: AS_IF is expanded from...
../../lib/autoconf/general.m4:2042: AC_CACHE_VAL is expanded from...
../../lib/autoconf/general.m4:2063: AC_CACHE_CHECK is expanded from...
configure.ac:375: the top level
Solution 9:
Use AC_LANG_SOURCE, or use proper quoting.
Problem 10 (in intl/):
configure.ac:7: warning: AC_COMPILE_IFELSE was called before AC_USE_SYSTEM_EXTENSIONS
/usr/share/aclocal/threadlib.m4:36: gl_THREADLIB_EARLY_BODY is expanded from...
/usr/share/aclocal/threadlib.m4:29: gl_THREADLIB_EARLY is expanded from...
/usr/share/aclocal/threadlib.m4:318: gl_THREADLIB is expanded from...
/usr/share/aclocal/lock.m4:9: gl_LOCK is expanded from...
/usr/share/aclocal/intl.m4:211: gt_INTL_SUBDIR_CORE is expanded from...
/usr/share/aclocal/intl.m4:25: AM_INTL_SUBDIR is expanded from...
/usr/share/aclocal/gettext.m4:57: AM_GNU_GETTEXT is expanded from...
configure.ac:7: the top level
Solution 10:
Add AC_USE_SYSTEM_EXTENSIONS in configure.ac.
ChangeLog:
* libtool.m4: Use AC_LANG_SOURCE.
* configure.ac: Remove AC_PREREQ, use AC_LANG_SOURCE.
* README-maintainer-mode: Update version requirements.
* ar-lib: New file.
* test-driver: New file.
* configure: Re-generate.
bfd/ChangeLog:
* Makefile.am (AUTOMAKE_OPTIONS): Remove 1.11.
(INCLUDES): Rename to ...
(AM_CPPFLAGS): ... this.
* configure.ac: Remove AC_PREREQ.
* doc/Makefile.am (AUTOMAKE_OPTIONS): Remove 1.9, cygnus, add
info-in-builddir no-texinfo.tex.
(info_TEXINFOS): Rename bfd.texinfo to bfd.texi.
* doc/bfd.texinfo: Rename to ...
* doc/bfd.texi: ... this.
* Makefile.in: Re-generate.
* aclocal.m4: Re-generate.
* config.in: Re-generate.
* configure: Re-generate.
* doc/Makefile.in: Re-generate.
binutils/ChangeLog:
* configure.ac: Remove AC_PREREQ.
* doc/Makefile.am (AUTOMAKE_OPTIONS): Remove cygnus, add
info-in-builddir no-texinfo.tex.
* Makefile.in: Re-generate.
* aclocal.m4: Re-generate.
* config.in: Re-generate.
* configure: Re-generate.
* doc/Makefile.in: Re-generate.
config/ChangeLog:
* override.m4 (_GCC_AUTOCONF_VERSION): Bump from 2.64 to 2.69.
etc/ChangeLog:
* configure.in: Remove AC_PREREQ.
* configure: Re-generate.
gas/ChangeLog:
* Makefile.am (AUTOMAKE_OPTIONS): Remove 1.11, add subdir-objects.
(TARG_CPU_O, OBJ_FORMAT_O, ATOF_TARG_O): Add config/ prefix.
* configure.ac (TARG_CPU_O, OBJ_FORMAT_O, ATOF_TARG_O, emfiles,
extra_objects): Add config/ prefix.
* doc/as.texinfo: Rename to...
* doc/as.texi: ... this.
* doc/Makefile.am: Rename as.texinfo to as.texi throughout.
Remove DISTCLEANFILES hack.
(AUTOMAKE_OPTIONS): Remove 1.8, cygnus, add no-texinfo.tex and
info-in-builddir.
* Makefile.in: Re-generate.
* aclocal.m4: Re-generate.
* config.in: Re-generate.
* configure: Re-generate.
* doc/Makefile.in: Re-generate.
gdb/ChangeLog:
* common/common-defs.h (PACKAGE_NAME, PACKAGE_VERSION,
PACKAGE_STRING, PACKAGE_TARNAME): Undefine.
* configure.ac: Remove AC_PREREQ, add missing quoting.
* gnulib/configure.ac: Modernize usage of
AC_INIT/AM_INIT_AUTOMAKE. Remove AC_PREREQ.
* gnulib/update-gnulib.sh (AUTOCONF_VERSION): Bump to 2.69.
(AUTOMAKE_VERSION): Bump to 1.15.1.
* configure: Re-generate.
* config.in: Re-generate.
* aclocal.m4: Re-generate.
* gnulib/aclocal.m4: Re-generate.
* gnulib/config.in: Re-generate.
* gnulib/configure: Re-generate.
* gnulib/import/Makefile.in: Re-generate.
gdb/gdbserver/ChangeLog:
* configure.ac: Remove AC_PREREQ, add missing quoting.
* configure: Re-generate.
* config.in: Re-generate.
* aclocal.m4: Re-generate.
gdb/testsuite/ChangeLog:
* configure.ac: Remove AC_PREREQ.
* configure: Re-generate.
gold/ChangeLog:
* configure.ac: Remove AC_PREREQ, add missing quoting and usage
of AC_LANG_SOURCE.
* Makefile.in: Re-generate.
* aclocal.m4: Re-generate.
* configure: Re-generate.
* testsuite/Makefile.in: Re-generate.
gprof/ChangeLog:
* configure.ac: Remove AC_PREREQ.
* Makefile.am: Remove DISTCLEANFILES hack.
(AUTOMAKE_OPTIONS): Remove 1.11, add info-in-builddir.
* Makefile.in: Re-generate.
* aclocal.m4: Re-generate.
* configure: Re-generate.
* gconfig.in: Re-generate.
intl/ChangeLog:
* configure.ac: Add AC_USE_SYSTEM_EXTENSIONS, remove AC_PREREQ.
* configure: Re-generate.
* config.h.in: Re-generate.
* aclocal.m4: Re-generate.
ld/ChangeLog:
* configure.ac: Remove AC_PREREQ.
* Makefile.am: Remove DISTCLEANFILES hack, rename ld.texinfo to
ld.texi, ldint.texinfo to ldint.texi throughout.
(AUTOMAKE_OPTIONS): Add info-in-builddir.
* README: Rename ld.texinfo to ld.texi, ldint.texinfo to
ldint.texi throughout.
* gen-doc.texi: Likewise.
* h8-doc.texi: Likewise.
* ld.texinfo: Rename to ...
* ld.texi: ... this.
* ldint.texinfo: Rename to ...
* ldint.texi: ... this.
* Makefile.in: Re-generate.
* aclocal.m4: Re-generate.
* config.in: Re-generate.
* configure: Re-generate.
libdecnumber/ChangeLog:
* configure.ac: Remove AC_PREREQ.
* configure: Re-generate.
* aclocal.m4.
libiberty/ChangeLog:
* configure.ac: Remove AC_PREREQ.
* configure: Re-generate.
* config.in: Re-generate.
opcodes/ChangeLog:
* Makefile.am (AUTOMAKE_OPTIONS): Remove 1.11.
* configure.ac: Remove AC_PREREQ.
* Makefile.in: Re-generate.
* aclocal.m4: Re-generate.
* configure: Re-generate.
readline/ChangeLog.gdb:
* configure: Re-generate.
* examples/rlfe/configure: Re-generate.
sim/ChangeLog:
* All configure.ac: Remove AC_PREREQ.
* All configure: Re-generate.
zlib/ChangeLog.bin-gdb:
* configure.ac: Modernize AC_INIT call, remove AC_PREREQ.
* Makefile.am (AUTOMAKE_OPTIONS): Remove 1.8, cygnus, add
foreign.
* Makefile.in: Re-generate.
* aclocal.m4: Re-generate.
* configure: Re-generate.
Add support for the Global INValidate Application Specific Extension
for Release 6 of the MIPS Architecture.
[1] "MIPS Architecture for Programmers Volume II-A: The MIPS32
Instruction Set Manual", Imagination Technologies Ltd., Document
Number: MD00086, Revision 6.06, December 15, 2016, Section 3.2
"Alphabetical List of Instructions", pp. 187-191
bfd/
* elfxx-mips.c (print_mips_ases): Add GINV extension.
binutils/
* readelf.c (print_mips_ases): Add GINV extension.
gas/
* NEWS: Mention MIPS Global INValidate ASE support.
* config/tc-mips.c (options): Add OPTION_GINV and OPTION_NO_GINV.
(md_longopts): Likewise.
(mips_ases): Define availability for GINV.
(mips_convert_ase_flags): Map ASE_GINV to AFL_ASE_GINV.
(md_show_usage): Add help for -mginv and -mno-ginv.
* doc/as.texinfo: Document -mginv, -mno-ginv.
* doc/c-mips.texi: Document -mginv, -mno-ginv, .set ginv and
.set noginv.
* testsuite/gas/mips/ase-errors-1.s: Add error checks for GINV
ASE.
* testsuite/gas/mips/ase-errors-2.s: Likewise.
* testsuite/gas/mips/ase-errors-1.l: Likewise.
* testsuite/gas/mips/ase-errors-2.l: Likewise.
* testsuite/gas/mips/ginv.d: New test.
* testsuite/gas/mips/ginv-err.d: New test.
* testsuite/gas/mips/ginv-err.l: New test stderr output.
* testsuite/gas/mips/ginv.s: New test source.
* testsuite/gas/mips/ginv-err.s: New test source.
* testsuite/gas/mips/mips.exp: Run the new tests.
include/
* elf/mips.h (AFL_ASE_GINV, AFL_ASE_RESERVED1): New macros.
(AFL_ASE_MASK): Update to include AFL_ASE_GINV.
* opcode/mips.h: Document "+\" operand format.
(ASE_GINV): New macro.
opcodes/
* mips-dis.c (mips_arch_choices): Add GINV to mips32r6 and
mips64r6 descriptors.
(parse_mips_ase_option): Handle -Mginv option.
(print_mips_disassembler_options): Document -Mginv.
* mips-opc.c (decode_mips_operand) <+\>: New operand format.
(GINV): New macro.
(mips_opcodes): Define ginvi and ginvt.
Add support for the CRC Application Specific Extension for Release 6 of
the MIPS Architecture.
[1] "MIPS Architecture for Programmers Volume II-A: The MIPS32
Instruction Set Manual", Imagination Technologies Ltd., Document
Number: MD00086, Revision 6.06, December 15, 2016, Section 3.2
"Alphabetical List of Instructions", pp. 143-148
[2] "MIPS Architecture for Programmers Volume II-A: The MIPS64
Instruction Set Manual", Imagination Technologies Ltd., Document
Number: MD00087, Revision 6.06, December 15, 2016, Section 3.2
"Alphabetical List of Instructions", pp. 165-170
ChangeLog:
bfd/
2018-06-13 Scott Egerton <scott.egerton@imgtec.com>
Faraz Shahbazker <Faraz.Shahbazker@mips.com>
* elfxx-mips.c (print_mips_ases): Add CRC.
binutils/
2018-06-13 Scott Egerton <scott.egerton@imgtec.com>
Faraz Shahbazker <Faraz.Shahbazker@mips.com>
* readelf.c (print_mips_ases): Add CRC.
gas/
2018-06-13 Scott Egerton <scott.egerton@imgtec.com>
Faraz Shahbazker <Faraz.Shahbazker@mips.com>
Maciej W. Rozycki <macro@mips.com>
* config/tc-mips.c (options): Add OPTION_CRC and OPTION_NO_CRC.
(md_longopts): Likewise.
(md_show_usage): Add help for -mcrc and -mno-crc.
(mips_ases): Define availability for CRC and CRC64.
(mips_convert_ase_flags): Map ASE_CRC to AFL_ASE_CRC.
* doc/as.texinfo: Document -mcrc, -mno-crc.
* doc/c-mips.texi: Document -mcrc, -mno-crc, .set crc and
.set no-crc.
* testsuite/gas/mips/ase-errors-1.l: Add error checks for CRC
ASE.
* testsuite/gas/mips/ase-errors-2.l: Likewise.
* testsuite/gas/mips/ase-errors-1.s: Likewise.
* testsuite/gas/mips/ase-errors-2.s: Likewise.
* testsuite/gas/mips/crc.d: New test.
* testsuite/gas/mips/crc64.d: New test.
* testsuite/gas/mips/crc-err.d: New test.
* testsuite/gas/mips/crc64-err.d: New test.
* testsuite/gas/mips/crc-err.l: New test stderr output.
* testsuite/gas/mips/crc64-err.l: New test stderr output.
* testsuite/gas/mips/crc.s: New test source.
* testsuite/gas/mips/crc64.s: New test source.
* testsuite/gas/mips/crc-err.s: New test source.
* testsuite/gas/mips/crc64-err.s: New test source.
* testsuite/gas/mips/mips.exp: Run the new tests.
include/
2018-06-13 Scott Egerton <scott.egerton@imgtec.com>
Faraz Shahbazker <Faraz.Shahbazker@mips.com>
* elf/mips.h (AFL_ASE_CRC): New macro.
(AFL_ASE_MASK): Update to include AFL_ASE_CRC.
* opcode/mips.h (ASE_CRC): New macro.
* opcode/mips.h (ASE_CRC64): Likewise.
opcodes/
2018-06-13 Scott Egerton <scott.egerton@imgtec.com>
Faraz Shahbazker <Faraz.Shahbazker@mips.com>
* mips-dis.c (mips_arch_choices): Add CRC and CRC64 ASEs.
* mips-opc.c (CRC, CRC64): New macros.
(mips_builtin_opcodes): Define crc32b, crc32h, crc32w,
crc32cb, crc32ch and crc32cw for CRC. Define crc32d and
crc32cd for CRC64.
Match commit 4ffff32f75 ("Match mips_optimize to the -O option
supplied") and adjust `--help' output for `-O0', `-O', `-O1' and `-O2'
options.
gas/
* config/tc-mips.c (md_show_usage): Correct help text for `-O0'
and `-O'. Mention `-O1'. Add `-O2' and its description.
This patch adds support to gas for -mcpu=cortex-a76 in the usual way.
make check-gas passes without problems.
2018-06-08 Kyrylo Tkachov <kyrylo.tkachov@arm.com>
* config/tc-arm.c (arm_cpus): Add Cortex-A76 entry.
* doc/c-arm.texi (-mcpu): Document cortex-a76.
This patch adds support to gas for -mcpu=cortex-a76 in the usual way.
make check-gas passes without problems.
2018-06-08 Kyrylo Tkachov <kyrylo.tkachov@arm.com>
* config/tc-aarch64.c (aarch64_cpus): Add Cortex-A76 entry.
* doc/c-aarch64.texi (-mcpu): Document cortex-a76.
Detect illegal FMOV instructions that changes the size from 32 bits to 64
bits and vice versa. Add tests for these and other undefined FMOV
instructions.
PR 20319
gas * testsuite/gas/aarch64/illegal-3.s: Test if unallocated FMOV encodings
are detected as undefined.
* testsuite/gas/aarch64/illegal-3.d: Likewise.
* testsuite/gas/aarch64/illegal.s: Test if FMOV instructions that are
changing the size from 32 bits to 64 bits and vice versa trigger an
error.
* testsuite/gas/aarch64/illegal.l: Likewise.
opcodes * aarch64-tbl.h: Introduce QL_INT2FP_FMOV and QL_FP2INT_FMOV.
(aarch64_opcode_table) : Use QL_INT2FP_FMOV and QL_FP2INT_FMOV.
This patch fixes an uninitialized memory issue that can under certain
circumstances turn an error into a warning because non_fatal was not initialised
in all cases.
Verified using valgrind.
gas/config/tc-aarch64.c
PR binutils/21446
* tc-aarch64.c (record_operand_error, record_operand_error_with_data):
Initialize non_fatal.
It is currently not possible to correctly match .xt.prop information
for sections with identical VMA. Allow creation of separate property
sections in the BFD. Add assembler option --separate-prop-tables to
allow creation of separate property sections.
2018-06-04 Volodymyr Arbatov <arbatov@cadence.com>
bfd/
* elf32-xtensa.c (elf32xtensa_separate_props): New global
variable.
(xtensa_add_names): New function.
(xtensa_property_section_name): Add new parameter
separate_sections, use it to choose property section name.
(xtensa_get_separate_property_section): New function.
(xtensa_get_property_section): Invoke
xtensa_get_separate_property_section to get individual property
section if it exists, common property section otherwise.
(xtensa_make_property_section): Pass elf32xtensa_separate_props
to xtensa_property_section_name.
gas/
* config/tc-xtensa.c (elf32xtensa_separate_props): New
declaration.
(option_separate_props, option_no_separate_props): New
enumeration constants.
(md_longopts): Add separate-prop-tables option.
(md_parse_option): Add cases for option_separate_props and
option_no_separate_props.
(md_show_usage): Add help for [no-]separate-prop-tables options.
Bump version number to 2.30.52 since _bfd_link_hide_symbol has been added
to bfd_target.
bfd/
* version.m4: Bump version to 2.30.52
* configure: Regenerated.
binutils/
* configure: Regenerated.
gas/
* configure: Regenerated.
gprof/
* configure: Regenerated.
ld/
* configure: Regenerated.
opcodes/
* configure: Regenerated.
Fix locviews on ia64. If we do not drop the view after copying line
info to slots in the bundle, we may attempt to compute the view more
than once and get very confused.
for gas/ChangeLog
* dwarf2dbg.c (dwarf2_consume_line_info): Drop view.
All REX bits can be specified via individual prefixes. Redundancy should
only be reported on a per-bit basis.
Note that I originally had further checks added to the test case,
checking the effect also on PDEP. I had to strip those, because my patch
to correctly handle those
(https://sourceware.org/ml/binutils/2017-02/msg00280.html) was rejected.
I continue to think that there should not be any new prefix introduced
to handle the VEX case - whether the encoding of an insn requires VEX et
al should not be of immediate interest to the programmer.
... as is already done elsewhere: There's no need for the use of
operand_type_equal() here - the bit identifying control registers isn't
used for any other purposes.
The control register is never expressed by REX.B; this bit only affects
the involved GPR. Also only one of the operands can have its "control"
flag set, so only check the correct operand.
This patch regenerates a number of files that either were edited by
hand or not regenerated when s12z support was added to binutils.
bfd/
* Makefile.in: Regenerate.
* po/SRC-POTFILES.in: Regenerate.
gas/
* po/POTFILES.in: Regenerate.
ld/
* po/BLD-POTFILES.in: Regenerate.
opcodes/
* Makefile.in: Regenerate.
* po/POTFILES.in: Regenerate.
bfd * Makefile.am: Add s12z files.
* Makefile.in: Regenerate.
* archures.c: Add bfd_s12z_arch.
* bfd-in.h: Add exports of bfd_putb24 and bfd_putl24.
* bfd-in2.h: Regenerate.
* config.bfd: Add s12z target.
* configure.ac: Add s12z target.
* configure: Regenerate.
* cpu-s12z.c: New file.
* elf32-s12z.c: New file.
* libbfd.c (bfd_putb24): New function.
(bfd_putl24): New function.
* libbfd.h: Regenerate.
* reloc.c: Add s12z relocations.
(bfd_get_reloc_size): Handle size 5 relocs.
* targets.c: Add s12z_elf32_vec.
opcodes * Makefile.am: Add support for s12z architecture.
* configure.ac: Likewise.
* disassemble.c: Likewise.
* disassemble.h: Likewise.
* Makefile.in: Regenerate.
* configure: Regenerate.
* s12z-dis.c: New file.
* s12z.h: New file.
include * elf/s12z.h: New header.
ld * Makefile.am: Add support for s12z architecture.
* configure.tgt: Likewise.
* Makefile.in: Regenerate.
* emulparams/m9s12zelf.sh: New file.
* scripttempl/elfm9s12z.sc: New file.
* testsuite/ld-discard/static.d: Expect to fail for the s12z
target.
* testsuite/ld-elf/endsym.d: Likewise.
* testsuite/ld-elf/merge.d: Likewise.
* testsuite/ld-elf/pr14926.d: Skip for the s12z target.
* testsuite/ld-elf/sec64k.exp: Likewise.
* testsuite/ld-s12z: New directory.
* testsuite/ld-s12z/opr-linking.d: New file.
* testsuite/ld-s12z/opr-linking.s: New file.
* testsuite/ld-s12z/relative-linking.d: New file.
* testsuite/ld-s12z/relative-linking.s: New file.
* testsuite/ld-s12z/z12s.exp: New file.
gas * Makefile.am: Add support for s12z target.
* Makefile.in: Regenerate.
* NEWS: Mention the new support.
* config/tc-s12z.c: New file.
* config/tc-s12z.h: New file.
* configure.tgt: Add s12z support.
* doc/Makefile.am: Likewise.
* doc/Makefile.in: Regenerate.
* doc/all.texi: Add s12z documentation.
* doc/as.textinfo: Likewise.
* doc/c-s12z.texi: New file.
* testsuite/gas/s12z: New directory.
* testsuite/gas/s12z/abs.d: New file.
* testsuite/gas/s12z/abs.s: New file.
* testsuite/gas/s12z/adc-imm.d: New file.
* testsuite/gas/s12z/adc-imm.s: New file.
* testsuite/gas/s12z/adc-opr.d: New file.
* testsuite/gas/s12z/adc-opr.s: New file.
* testsuite/gas/s12z/add-imm.d: New file.
* testsuite/gas/s12z/add-imm.s: New file.
* testsuite/gas/s12z/add-opr.d: New file.
* testsuite/gas/s12z/add-opr.s: New file.
* testsuite/gas/s12z/and-imm.d: New file.
* testsuite/gas/s12z/and-imm.s: New file.
* testsuite/gas/s12z/and-opr.d: New file.
* testsuite/gas/s12z/and-opr.s: New file.
* testsuite/gas/s12z/and-or-cc.d: New file.
* testsuite/gas/s12z/and-or-cc.s: New file.
* testsuite/gas/s12z/bfext-special.d: New file.
* testsuite/gas/s12z/bfext-special.s: New file.
* testsuite/gas/s12z/bfext.d: New file.
* testsuite/gas/s12z/bfext.s: New file.
* testsuite/gas/s12z/bit-manip.d: New file.
* testsuite/gas/s12z/bit-manip.s: New file.
* testsuite/gas/s12z/bit.d: New file.
* testsuite/gas/s12z/bit.s: New file.
* testsuite/gas/s12z/bra-expression-defined.d: New file.
* testsuite/gas/s12z/bra-expression-defined.s: New file.
* testsuite/gas/s12z/bra-expression-undef.d: New file.
* testsuite/gas/s12z/bra-expression-undef.s: New file.
* testsuite/gas/s12z/bra.d: New file.
* testsuite/gas/s12z/bra.s: New file.
* testsuite/gas/s12z/brclr-symbols.d: New file.
* testsuite/gas/s12z/brclr-symbols.s: New file.
* testsuite/gas/s12z/brset-clr-opr-imm-rel.d: New file.
* testsuite/gas/s12z/brset-clr-opr-imm-rel.s: New file.
* testsuite/gas/s12z/brset-clr-opr-reg-rel.d: New file.
* testsuite/gas/s12z/brset-clr-opr-reg-rel.s: New file.
* testsuite/gas/s12z/brset-clr-reg-imm-rel.d: New file.
* testsuite/gas/s12z/brset-clr-reg-imm-rel.s: New file.
* testsuite/gas/s12z/brset-clr-reg-reg-rel.d: New file.
* testsuite/gas/s12z/brset-clr-reg-reg-rel.s: New file.
* testsuite/gas/s12z/clb.d: New file.
* testsuite/gas/s12z/clb.s: New file.
* testsuite/gas/s12z/clr-opr.d: New file.
* testsuite/gas/s12z/clr-opr.s: New file.
* testsuite/gas/s12z/clr.d: New file.
* testsuite/gas/s12z/clr.s: New file.
* testsuite/gas/s12z/cmp-imm.d: New file.
* testsuite/gas/s12z/cmp-imm.s: New file.
* testsuite/gas/s12z/cmp-opr-inc.d: New file.
* testsuite/gas/s12z/cmp-opr-inc.s: New file.
* testsuite/gas/s12z/cmp-opr-rdirect.d: New file.
* testsuite/gas/s12z/cmp-opr-rdirect.s: New file.
* testsuite/gas/s12z/cmp-opr-reg.d: New file.
* testsuite/gas/s12z/cmp-opr-reg.s: New file.
* testsuite/gas/s12z/cmp-opr-rindirect.d: New file.
* testsuite/gas/s12z/cmp-opr-rindirect.s: New file.
* testsuite/gas/s12z/cmp-opr-sxe4.d: New file.
* testsuite/gas/s12z/cmp-opr-sxe4.s: New file.
* testsuite/gas/s12z/cmp-opr-xys.d: New file.
* testsuite/gas/s12z/cmp-opr-xys.s: New file.
* testsuite/gas/s12z/cmp-s-imm.d: New file.
* testsuite/gas/s12z/cmp-s-imm.s: New file.
* testsuite/gas/s12z/cmp-s-opr.d: New file.
* testsuite/gas/s12z/cmp-s-opr.s: New file.
* testsuite/gas/s12z/cmp-xy.d: New file.
* testsuite/gas/s12z/cmp-xy.s: New file.
* testsuite/gas/s12z/com-opr.d: New file.
* testsuite/gas/s12z/com-opr.s: New file.
* testsuite/gas/s12z/complex-shifts.d: New file.
* testsuite/gas/s12z/complex-shifts.s: New file.
* testsuite/gas/s12z/db-tb-cc-opr.d: New file.
* testsuite/gas/s12z/db-tb-cc-opr.s: New file.
* testsuite/gas/s12z/db-tb-cc-reg.d: New file.
* testsuite/gas/s12z/db-tb-cc-reg.s: New file.
* testsuite/gas/s12z/dbCC.d: New file.
* testsuite/gas/s12z/dbCC.s: New file.
* testsuite/gas/s12z/dec-opr.d: New file.
* testsuite/gas/s12z/dec-opr.s: New file.
* testsuite/gas/s12z/dec.d: New file.
* testsuite/gas/s12z/dec.s: New file.
* testsuite/gas/s12z/div.d: New file.
* testsuite/gas/s12z/div.s: New file.
* testsuite/gas/s12z/eor.d: New file.
* testsuite/gas/s12z/eor.s: New file.
* testsuite/gas/s12z/exg.d: New file.
* testsuite/gas/s12z/exg.s: New file.
* testsuite/gas/s12z/ext24-ld-xy.d: New file.
* testsuite/gas/s12z/ext24-ld-xy.s: New file.
* testsuite/gas/s12z/inc-opr.d: New file.
* testsuite/gas/s12z/inc-opr.s: New file.
* testsuite/gas/s12z/inc.d: New file.
* testsuite/gas/s12z/inc.s: New file.
* testsuite/gas/s12z/inh.d: New file.
* testsuite/gas/s12z/inh.s: New file.
* testsuite/gas/s12z/jmp.d: New file.
* testsuite/gas/s12z/jmp.s: New file.
* testsuite/gas/s12z/jsr.d: New file.
* testsuite/gas/s12z/jsr.s: New file.
* testsuite/gas/s12z/ld-imm-page2.d: New file.
* testsuite/gas/s12z/ld-imm-page2.s: New file.
* testsuite/gas/s12z/ld-imm.d: New file.
* testsuite/gas/s12z/ld-imm.s: New file.
* testsuite/gas/s12z/ld-immu18.d: New file.
* testsuite/gas/s12z/ld-immu18.s: New file.
* testsuite/gas/s12z/ld-large-direct.d: New file.
* testsuite/gas/s12z/ld-large-direct.s: New file.
* testsuite/gas/s12z/ld-opr.d: New file.
* testsuite/gas/s12z/ld-opr.s: New file.
* testsuite/gas/s12z/ld-s-opr.d: New file.
* testsuite/gas/s12z/ld-s-opr.s: New file.
* testsuite/gas/s12z/ld-small-direct.d: New file.
* testsuite/gas/s12z/ld-small-direct.s: New file.
* testsuite/gas/s12z/lea-immu18.d: New file.
* testsuite/gas/s12z/lea-immu18.s: New file.
* testsuite/gas/s12z/lea.d: New file.
* testsuite/gas/s12z/lea.s: New file.
* testsuite/gas/s12z/mac.d: New file.
* testsuite/gas/s12z/mac.s: New file.
* testsuite/gas/s12z/min-max.d: New file.
* testsuite/gas/s12z/min-max.s: New file.
* testsuite/gas/s12z/mod.d: New file.
* testsuite/gas/s12z/mod.s: New file.
* testsuite/gas/s12z/mov.d: New file.
* testsuite/gas/s12z/mov.s: New file.
* testsuite/gas/s12z/mul-imm.d: New file.
* testsuite/gas/s12z/mul-imm.s: New file.
* testsuite/gas/s12z/mul-opr-opr.d: New file.
* testsuite/gas/s12z/mul-opr-opr.s: New file.
* testsuite/gas/s12z/mul-opr.d: New file.
* testsuite/gas/s12z/mul-opr.s: New file.
* testsuite/gas/s12z/mul-reg.d: New file.
* testsuite/gas/s12z/mul-reg.s: New file.
* testsuite/gas/s12z/mul.d: New file.
* testsuite/gas/s12z/mul.s: New file.
* testsuite/gas/s12z/neg-opr.d: New file.
* testsuite/gas/s12z/neg-opr.s: New file.
* testsuite/gas/s12z/not-so-simple-shifts.d: New file.
* testsuite/gas/s12z/not-so-simple-shifts.s: New file.
* testsuite/gas/s12z/opr-18u.d: New file.
* testsuite/gas/s12z/opr-18u.s: New file.
* testsuite/gas/s12z/opr-expr.d: New file.
* testsuite/gas/s12z/opr-expr.s: New file.
* testsuite/gas/s12z/opr-ext-18.d: New file.
* testsuite/gas/s12z/opr-ext-18.s: New file.
* testsuite/gas/s12z/opr-idx-24-reg.d: New file.
* testsuite/gas/s12z/opr-idx-24-reg.s: New file.
* testsuite/gas/s12z/opr-idx3-reg.d: New file.
* testsuite/gas/s12z/opr-idx3-reg.s: New file.
* testsuite/gas/s12z/opr-idx3-xysp-24.d: New file.
* testsuite/gas/s12z/opr-idx3-xysp-24.s: New file.
* testsuite/gas/s12z/opr-indirect-expr.d: New file.
* testsuite/gas/s12z/opr-indirect-expr.s: New file.
* testsuite/gas/s12z/opr-symbol.d: New file.
* testsuite/gas/s12z/opr-symbol.s: New file.
* testsuite/gas/s12z/or-imm.d: New file.
* testsuite/gas/s12z/or-imm.s: New file.
* testsuite/gas/s12z/or-opr.d: New file.
* testsuite/gas/s12z/or-opr.s: New file.
* testsuite/gas/s12z/p2-mul.d: New file.
* testsuite/gas/s12z/p2-mul.s: New file.
* testsuite/gas/s12z/page2-inh.d: New file.
* testsuite/gas/s12z/page2-inh.s: New file.
* testsuite/gas/s12z/psh-pul.d: New file.
* testsuite/gas/s12z/psh-pul.s: New file.
* testsuite/gas/s12z/qmul.d: New file.
* testsuite/gas/s12z/qmul.s: New file.
* testsuite/gas/s12z/rotate.d: New file.
* testsuite/gas/s12z/rotate.s: New file.
* testsuite/gas/s12z/s12z.exp: New file.
* testsuite/gas/s12z/sat.d: New file.
* testsuite/gas/s12z/sat.s: New file.
* testsuite/gas/s12z/sbc-imm.d: New file.
* testsuite/gas/s12z/sbc-imm.s: New file.
* testsuite/gas/s12z/sbc-opr.d: New file.
* testsuite/gas/s12z/sbc-opr.s: New file.
* testsuite/gas/s12z/shift.d: New file.
* testsuite/gas/s12z/shift.s: New file.
* testsuite/gas/s12z/simple-shift.d: New file.
* testsuite/gas/s12z/simple-shift.s: New file.
* testsuite/gas/s12z/single-ops.d: New file.
* testsuite/gas/s12z/single-ops.s: New file.
* testsuite/gas/s12z/specd6.d: New file.
* testsuite/gas/s12z/specd6.s: New file.
* testsuite/gas/s12z/st-large-direct.d: New file.
* testsuite/gas/s12z/st-large-direct.s: New file.
* testsuite/gas/s12z/st-opr.d: New file.
* testsuite/gas/s12z/st-opr.s: New file.
* testsuite/gas/s12z/st-s-opr.d: New file.
* testsuite/gas/s12z/st-s-opr.s: New file.
* testsuite/gas/s12z/st-small-direct.d: New file.
* testsuite/gas/s12z/st-small-direct.s: New file.
* testsuite/gas/s12z/st-xy.d: New file.
* testsuite/gas/s12z/st-xy.s: New file.
* testsuite/gas/s12z/sub-imm.d: New file.
* testsuite/gas/s12z/sub-imm.s: New file.
* testsuite/gas/s12z/sub-opr.d: New file.
* testsuite/gas/s12z/sub-opr.s: New file.
* testsuite/gas/s12z/tfr.d: New file.
* testsuite/gas/s12z/tfr.s: New file.
* testsuite/gas/s12z/trap.d: New file.
* testsuite/gas/s12z/trap.s: New file.
binutils* readelf.c: Add support for s12z architecture.
* testsuite/lib/binutils-common.exp (is_elf_format): Excluse s12z
targets.
Remove `-Wshadow' compilation errors:
cc1: warnings being treated as errors
.../gas/config/tc-nds32.c: In function 'md_assemble':
.../gas/config/tc-nds32.c:5212: error: declaration of 'expr' shadows a global declaration
.../gas/expr.h:180: error: shadowed declaration is here
make[4]: *** [tc-nds32.o] Error 1
which for versions of GCC before 4.8 prevent support for NDS32 targets
from being built. See also GCC PR c/53066.
gas/
* tc-nds32.c (md_assemble): Rename `expr' local variable to
`insn_expr'.
Jan Beulich
Jeff Law
Tamar Christina
Nick Clifton
Maciej W. Rozycki
Thomas Preud'homme
Jim Wilson
Ramana Radhakrishnan
Alan Modra
Sebastian Huber
Simon Marchi
Faraz Shahbazker
Scott Egerton
kyrtka01
Egeyar Bagcioglu
Sameera Deshpande
Max Filippov
H.J. Lu
Alexandre Oliva
Amit Pawar
Peter Bergner
John Darrington