In get_phys_addr_with_struct(), we call get_phys_addr_twostage() if
the CPU supports EL2. However, we don't check here that stage 2 is
actually enabled. Instead we only check that inside
get_phys_addr_twostage() to skip stage 2 translation. This means
that even if stage 2 is disabled we still tell the stage 1 lookup to
do its page table walks via stage 2.
This works by luck for normal CPU accesses, but it breaks for debug
accesses, which are used by the disassembler and also by semihosting
file reads and writes, because the debug case takes a different code
path inside S1_ptw_translate().
This means that setups that use semihosting for file loads are broken
(a regression since 7.1, introduced in recent ptw refactoring), and
that sometimes disassembly in debug logs reports "unable to read
memory" rather than showing the guest insns.
Fix the bug by hoisting the "is stage 2 enabled?" check up to
get_phys_addr_with_struct(), so that we handle S2 disabled the same
way we do the "no EL2" case, with a simple single stage lookup.
Reported-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221121212404.1450382-1-peter.maydell@linaro.org
With LPA2, the effective output address size is at most 48 bits when
TCR.DS == 0. This case is currently unhandled in the page table walker,
where we happily assume LVA/64k granule when outputsize > 48 and
param.ds == 0, resulting in the wrong conversion to be used from a
page table descriptor to a physical address.
if (outputsize > 48) {
if (param.ds) {
descaddr |= extract64(descriptor, 8, 2) << 50;
} else {
descaddr |= extract64(descriptor, 12, 4) << 48;
}
So cap the outputsize to 48 when TCR.DS is cleared, as per the
architecture.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221116170316.259695-1-ardb@kernel.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reversed the sense of non-secure in get_phys_addr_lpae,
and failed to initialize attrs.secure for ARMMMUIdx_Phys_S.
Fixes: 48da29e4 ("target/arm: Add ptw_idx to S1Translate")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1293
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We need to check HCR_E2H and HCR_TGE to select the right MMU index for
the correct translation regime.
To check for EL2&0 translation regime:
- For S1E0*, S1E1* and S12E* ops, check both HCR_E2H and HCR_TGE
- For S1E2* ops, check only HCR_E2H
Signed-off-by: Ake Koomsin <ake@igel.co.jp>
Message-id: 20221101064250.12444-1-ake@igel.co.jp
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With odd_ofs set, we weren't copying enough data.
Fixes: 09eb6d7025 ("target/arm: Move sve zip high_ofs into simd_data")
Reported-by: Idan Horowitz <idan.horowitz@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221031054144.3574-1-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When we implemented the PAN support we theoretically wanted
to support it for both AArch32 and AArch64, but in practice
several bugs made it essentially unusable with an AArch32
guest. Fix all those problems:
- Use CPSR.PAN to check for PAN state in aarch32 mode
- throw permission fault during address translation when PAN is
enabled and kernel tries to access user acessible page
- ignore SCTLR_XP bit for armv7 and armv8 (conflicts with SCTLR_SPAN).
Signed-off-by: Timofey Kutergin <tkutergin@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221027112619.2205229-1-tkutergin@gmail.com
[PMM: tweak commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The HCR_EL2.TTLB bit is supposed to trap all EL1 execution of TLB
maintenance instructions. However we have added new TLB insns for
FEAT_TLBIOS and FEAT_TLBIRANGE, and forgot to set their accessfn to
access_ttlb. Add the missing accessfns.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
The value passed is always true, and if the target's
synchronize_from_tb hook is non-trivial, not exiting
may be erroneous.
Reviewed-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We had only been reporting the stage2 page size. This causes
problems if stage1 is using a larger page size (16k, 2M, etc),
but stage2 is using a smaller page size, because cputlb does
not set large_page_{addr,mask} properly.
Fix by using the max of the two page sizes.
Reported-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221024051851.3074715-15-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Perform the atomic update for hardware management of the dirty bit.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221024051851.3074715-14-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Perform the atomic update for hardware management of the access flag.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221024051851.3074715-13-richard.henderson@linaro.org
[PMM: Fix accidental PROT_WRITE to PAGE_WRITE; add missing
main-loop.h include]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Replace some gotos with some nested if statements.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20221024051851.3074715-12-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Both GP and DBM are in the upper attribute block.
Extend the computation of attrs to include them,
then simplify the setting of guarded.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20221024051851.3074715-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Leave the upper and lower attributes in the place they originate
from in the descriptor. Shifting them around is confusing, since
one cannot read the bit numbers out of the manual. Also, new
attributes have been added which would alter the shifts.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20221024051851.3074715-10-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Always overriding fi->type was incorrect, as we would not properly
propagate the fault type from S1_ptw_translate, or arm_ldq_ptw.
Simplify things by providing a new label for a translation fault.
For other faults, store into fi directly.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20221024051851.3074715-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The unconditional loop was used both to iterate over levels
and to control parsing of attributes. Use an explicit goto
in both cases.
While this appears less clean for iterating over levels, we
will need to jump back into the middle of this loop for
atomic updates, which is even uglier.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221024051851.3074715-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This fault type is to be used with FEAT_HAFDBS when
the guest enables hw updates, but places the tables
in memory where atomic updates are unsupported.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20221024051851.3074715-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Separate S1 translation from the actual lookup.
Will enable lpae hardware updates.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221024051851.3074715-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20221024051851.3074715-5-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The MMFR1 field may indicate support for hardware update of
access flag alone, or access flag and dirty bit.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221024051851.3074715-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hoist the computation of the mmu_idx for the ptw up to
get_phys_addr_with_struct and get_phys_addr_twostage.
This removes the duplicate check for stage2 disabled
from the middle of the walk, performing it only once.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20221024051851.3074715-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reduce the amount of typing required for this check.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221024051851.3074715-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An exception targeting EL2 from lower EL is actually maskable when
HCR_E2H and HCR_TGE are both set. This applies to both secure and
non-secure Security state.
We can remove the conditions that try to suppress masking of
interrupts when we are Secure and the exception targets EL2 and
Secure EL2 is disabled. This is OK because in that situation
arm_phys_excp_target_el() will never return 2 as the target EL. The
'not if secure' check in this function was originally written before
arm_hcr_el2_eff(), and back then the target EL returned by
arm_phys_excp_target_el() could be 2 even if we were in Secure
EL0/EL1; but it is no longer needed.
Signed-off-by: Ake Koomsin <ake@igel.co.jp>
Message-id: 20221017092432.546881-1-ake@igel.co.jp
[PMM: Add commit message paragraph explaining why it's OK to
remove the checks on secure and SCR_EEL2]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
FEAT_E0PD adds new bits E0PD0 and E0PD1 to TCR_EL1, which allow the
OS to forbid EL0 access to half of the address space. Since this is
an EL0-specific variation on the existing TCR_ELx.{EPD0,EPD1}, we can
implement it entirely in aa64_va_parameters().
This requires moving the existing regime_is_user() to internals.h
so that the code in helper.c can get at it.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221021160131.3531787-1-peter.maydell@linaro.org
Since the only user, Arm MTE, always requires allocation,
merge the get and alloc functions to always produce a
non-null result. Also assume that the user has already
checked page validity.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Use a constant target data allocation size for all pages.
This will be necessary to reduce overhead of page tracking.
Since TARGET_PAGE_DATA_SIZE is now required, we can use this
to omit data tracking for targets that don't require it.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221020030641.2066807-10-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for TARGET_TB_PCREL, reduce reliance on absolute values.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221020030641.2066807-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for TARGET_TB_PCREL, reduce reliance on absolute values.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221020030641.2066807-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for TARGET_TB_PCREL, reduce reliance on absolute values.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221020030641.2066807-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for TARGET_TB_PCREL, reduce reliance on absolute values.
Since we always pass dc->pc_curr, fold the arithmetic to zero displacement.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221020030641.2066807-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for TARGET_TB_PCREL, reduce reliance on absolute values.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221020030641.2066807-5-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for TARGET_TB_PCREL, reduce reliance on
absolute values by passing in pc difference.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221020030641.2066807-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for TARGET_TB_PCREL, reduce reliance on absolute values.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221020030641.2066807-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A simple helper to retrieve the length of the current insn.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221020030641.2066807-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The return type of the functions is already bool, but in a few
instances we used an integer type with the return statement.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221011031911.2408754-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221011031911.2408754-12-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
So far, limit the change to S1_ptw_translate, arm_ldl_ptw, and
arm_ldq_ptw. Use probe_access_full to find the host address,
and if so use a host load. If the probe fails, we've got our
fault info already. On the off chance that page tables are not
in RAM, continue to use the address_space_ld* functions.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221011031911.2408754-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Hoist this test out of arm_ld[lq]_ptw into S1_ptw_translate.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221011031911.2408754-10-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Before using softmmu page tables for the ptw, plumb down
a debug parameter so that we can query page table entries
from gdbstub without modifying cpu state.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221011031911.2408754-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Consolidate most of the inputs and outputs of S1_ptw_translate
into a single structure. Plumb this through arm_ld*_ptw from
the controlling get_phys_addr_* routine.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221011031911.2408754-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Compare only the VMID field when considering whether we need to flush.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221011031911.2408754-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We had been marking this ARM_MMU_IDX_NOTLB, move it to a real tlb.
Flush the tlb when invalidating stage 1+2 translations. Re-use
alle1_tlbmask() for other instances of EL1&0 + Stage2.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221011031911.2408754-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Not yet used, but add mmu indexes for 1-1 mapping
to physical addresses.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221011031911.2408754-5-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a field to TARGET_PAGE_ENTRY_EXTRA to hold the guarded bit.
In is_guarded_page, use probe_access_full instead of just guessing
that the tlb entry is still present. Also handles the FIXME about
executing from device memory.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221011031911.2408754-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The CPUTLBEntryFull structure now stores the original pte attributes, as
well as the physical address. Therefore, we no longer need a separate
bit in MemTxAttrs, nor do we need to walk the tree of memory regions.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221011031911.2408754-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Copy attrs and shareability, into the TLB. This will eventually
be used by S1_ptw_translate to report stage1 translation failures,
and by do_ats_write to fill in PAR_EL1.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221011031911.2408754-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU doesn't model micro-architectural details which includes most
chip errata. The ARM_ERRATA_798181 work around in the Linux
kernel (see erratum_a15_798181_init) currently detects QEMU's
cortex-a15 as broken and triggers additional expensive TLB flushes as
a result.
Change the MIDR to report what the latest silicon would (r4p0). We
explicitly set the IMPDEF revidr bits to 0 because we don't need to
set anything other than the silicon revision to indicate these flushes
are not needed. This cuts about 5s from my Debian kernel boot with the
latest 6.0rc1 kernel (29s->24s).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Message-id: 20221010153225.506394-1-alex.bennee@linaro.org
Cc: Arnd Bergmann <arnd@linaro.org>
Cc: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Message-Id: <20220906172257.2776521-1-alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now we have an enum for the granule size, use it in the
ARMVAParameters struct instead of the using16k/using64k bools.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221003162315.2833797-3-peter.maydell@linaro.org
Arm CPUs support some subset of the granule (page) sizes 4K, 16K and
64K. The guest selects the one it wants using bits in the TCR_ELx
registers. If it tries to program these registers with a value that
is either reserved or which requests a size that the CPU does not
implement, the architecture requires that the CPU behaves as if the
field was programmed to some size that has been implemented.
Currently we don't implement this, and instead let the guest use any
granule size, even if the CPU ID register fields say it isn't
present.
Make aa64_va_parameters() check against the supported granule size
and force use of a different one if it is not implemented.
(A subsequent commit will make ARMVAParameters use the new enum
rather than the current pair of using16k/using64k bools.)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221003162315.2833797-2-peter.maydell@linaro.org
Adjust GetPhysAddrResult to fill in CPUTLBEntryFull,
so that it may be passed directly to tlb_set_page_full.
The change is large, but mostly mechanical. The major
non-mechanical change is page_size -> lg_page_size.
Most of the time this is obvious, and is related to
TARGET_PAGE_BITS.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221001162318.153420-21-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Do not apply memattr or shareability for Stage2 translations.
Make sure to apply HCR_{DC,DCT} only to Regime_EL10, per the
pseudocode in AArch64.S1DisabledOutput.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221001162318.153420-20-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-19-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use arm_hcr_el2_eff_secstate instead of arm_hcr_el2_eff, so
that we use is_secure instead of the current security state.
These AT* operations have been broken since arm_hcr_el2_eff
gained a check for "el2 enabled" for Secure EL2.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-18-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These subroutines did not need ENV for anything except
retrieving the effective value of HCR anyway.
We have computed the effective value of HCR in the callers,
and this will be especially important for interpreting HCR
in a non-current security state.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-17-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This value is unused.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221001162318.153420-16-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Rename the argument to is_secure_ptr, and introduce a
local variable is_secure with the value. We only write
back to the pointer toward the end of the function.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-15-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For page walking, we may require HCR for a security state
that is not "current".
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-14-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The effect of TGE does not only apply to non-secure state,
now that Secure EL2 exists.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use a switch on mmu_idx for the a-profile indexes, instead of
three different if's vs regime_el and arm_mmu_idx_is_stage1_of_2.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-12-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For a-profile aarch64, which does not bank system registers, it takes
quite a lot of code to switch between security states. In the process,
registers such as TCR_EL{1,2} must be swapped, which in itself requires
the flushing of softmmu tlbs. Therefore it doesn't buy us anything to
separate tlbs by security state.
Retain the distinction between Stage2 and Stage2_S.
This will be important as we implement FEAT_RME, and do not wish to
add a third set of mmu indexes for Realm state.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-11-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use get_phys_addr_with_secure directly. For a-profile, this is the
one place where the value of is_secure may not equal arm_is_secure(env).
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-10-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the last use of regime_is_secure; remove it
entirely before changing the layout of ARMMMUIdx.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-9-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the use of regime_is_secure from arm_tr_init_disas_context.
Instead, provide the value of v8m_secure directly from tb_flags.
Rather than use regime_is_secure, use the env->v7m.secure directly,
as per arm_mmu_idx_el.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-8-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the use of regime_is_secure from v7m_read_half_insn, using
the new parameter instead.
As it happens, both callers pass true, propagated from the argument
to arm_v7m_mmu_idx_for_secstate which created the mmu_idx argument,
but that is a detail of v7m_handle_execute_nsc we need not expose
to the callee.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-7-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Retain the existing get_phys_addr interface using the security
state derived from mmu_idx. Move the kerneldoc comments to the
header file where they belong.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-6-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the use of regime_is_secure from regime_translation_disabled,
using the new parameter instead.
This fixes a bug in S1_ptw_translate and get_phys_addr where we had
passed ARMMMUIdx_Stage2 and not ARMMMUIdx_Stage2_S to determine if
Stage2 is disabled, affecting FEAT_SEL2.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-5-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Pass the correct stage2 mmu_idx to regime_translation_disabled,
which we computed afterward.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221001162318.153420-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the use of regime_is_secure from get_phys_addr_lpae,
using the new parameter instead.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221001162318.153420-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While the stage2 call to get_phys_addr_lpae should never set
attrs.secure when given a non-secure input, it's just as easy
to make the final update to attrs.secure be unconditional and
false in the case of non-secure input.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221007152159.1414065-1-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The starting security state comes with the translation regime,
not the current state of arm_is_secure_below_el3().
Create a new local variable, s2walk_secure, which does not need
to be written back to result->attrs.secure -- we compute that
value later, after the S2 walk is complete.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20221001162318.153420-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Updates write_scr() to allow setting SCR_EL3.EnTP2 when FEAT_SME is
implemented. SCR_EL3 being a 64-bit register, valid_mask is changed
to uint64_t and the SCR_* constants in target/arm/cpu.h are extended
to 64-bit so that masking and bitwise not (~) behave as expected.
This enables booting Linux with Trusted Firmware-A at EL3 with
"-M virt,secure=on -cpu max".
Cc: qemu-stable@nongnu.org
Fixes: 78cb977666 ("target/arm: Enable SME for -cpu max")
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20221004072354.27037-1-jerome.forissier@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Occasionally the KVM_CREATE_VM ioctl can return EINTR, even though
there is no pending signal to be taken. In commit 94ccff1338
we added a retry-on-EINTR loop to the KVM_CREATE_VM call in the
generic KVM code. Adopt the same approach for the use of the
ioctl in the Arm-specific KVM code (where we use it to create a
scratch VM for probing for various things).
For more information, see the mailing list thread:
https://lore.kernel.org/qemu-devel/8735e0s1zw.wl-maz@kernel.org/
Reported-by: Vitaly Chikunov <vt@altlinux.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Vitaly Chikunov <vt@altlinux.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Message-id: 20220930113824.1933293-1-peter.maydell@linaro.org
Several hypervisor capabilities in KVM are target-specific. When exposed
to QEMU users as accelerator properties (i.e. -accel kvm,prop=value), they
should not be available for all targets.
Add a hook for targets to add their own properties to -accel kvm, for
now no such property is defined.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20220929072014.20705-3-chenyi.qiang@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It's always better to convey the type of a pointer if at all
possible. So let's add the DumpState typedef to typedefs.h and move
the dump note functions from the opaque pointers to DumpState
pointers.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Cédric Le Goater <clg@kaod.org>
CC: Daniel Henrique Barboza <danielhb413@gmail.com>
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Greg Kurz <groug@kaod.org>
CC: Palmer Dabbelt <palmer@dabbelt.com>
CC: Alistair Francis <alistair.francis@wdc.com>
CC: Bin Meng <bin.meng@windriver.com>
CC: Cornelia Huck <cohuck@redhat.com>
CC: Thomas Huth <thuth@redhat.com>
CC: Richard Henderson <richard.henderson@linaro.org>
CC: David Hildenbrand <david@redhat.com>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220811121111.9878-2-frankja@linux.ibm.com>
The availability of tb->pc will shortly be conditional.
Introduce accessor functions to minimize ifdefs.
Pass around a known pc to places like tcg_gen_code,
where the caller must already have the value.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This structure will shortly contain more than just
data for accessing MMIO. Rename the 'addr' member
to 'xlat_section' to more clearly indicate its purpose.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
SP_EL1 must be kept when EL3 is present but EL2 is not. Therefore mark
it with ARM_CP_EL3_NO_EL2_KEEP.
Cc: qemu-stable@nongnu.org
Fixes: 696ba37718 ("target/arm: Handle cpreg registration for missing EL")
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220927120058.670901-1-jerome.forissier@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
cpu64.c has ended up in a slightly odd order -- it starts with the
initfns for most of the models-real-hardware CPUs; after that comes a
bunch of support code for SVE, SME, pauth and LPA2 properties. Then
come the initfns for the 'host' and 'max' CPU types, and then after
that one more models-real-hardware CPU initfn, for a64fx. (This
ordering is partly historical and partly required because a64fx needs
the SVE properties.)
Reorder the file into:
* CPU property support functions
* initfns for real hardware CPUs
* initfns for host and max
* class boilerplate
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Our SDCR_VALID_MASK doesn't include all of the bits which are defined
by the current architecture. In particular in commit 0b42f4fab9 we
forgot to add SCCD, which meant that an AArch32 guest couldn't
actually use the SCCD bit to disable counting in Secure state.
Add all the currently defined bits; we don't implement all of them,
but this makes them be reads-as-written, which is architecturally
valid and matches how we currently handle most of the others in the
mask.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220923123412.1214041-4-peter.maydell@linaro.org
In commit 01765386a8 we fixed a bug where we weren't correctly
bracketing changes to some registers with pmu_op_start() and
pmu_op_finish() calls for changes which affect whether the PMU
counters might be enabled. However, we missed the case of writes to
the AArch64 MDCR_EL3 register, because (unlike its AArch32
counterpart) they are currently done directly to the CPU state struct
without going through the sdcr_write() function.
Give MDCR_EL3 a writefn which handles the PMU start/finish calls.
The SDCR writefn then simplfies to "call the MDCR_EL3 writefn after
masking off the bits which don't exist in the AArch32 register".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220923123412.1214041-3-peter.maydell@linaro.org
In commit 01765386a8 we made some system register write functions
call pmu_op_start()/pmu_op_finish(). This means that they now touch
timers, so for icount to work these registers must have the ARM_CP_IO
flag set.
This fixes a bug where when icount is enabled a guest that touches
MDCR_EL3, MDCR_EL2, PMCNTENSET_EL0 or PMCNTENCLR_EL0 would cause
QEMU to print an error message and exit, for example:
[ 2.495971] TCP: Hash tables configured (established 1024 bind 1024)
[ 2.496213] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 2.496386] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 2.496917] NET: Registered protocol family 1
qemu-system-aarch64: Bad icount read
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220923123412.1214041-2-peter.maydell@linaro.org
Remove the use of regime_is_secure from get_phys_addr_pmsav5.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-21-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the use of regime_is_secure from get_phys_addr_pmsav7,
using the new parameter instead.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-19-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the use of regime_is_secure from pmsav7_use_background_region,
using the new parameter instead.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-17-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the use of regime_is_secure from get_phys_addr_pmsav8.
Since we already had a local variable named secure, use that.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-16-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the use of regime_is_secure from get_phys_addr_v6,
passing the new parameter to the lookup instead.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-15-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the use of regime_is_secure from get_phys_addr_v5,
passing the new parameter to the lookup instead.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
[PMM: Folded in definition of local is_secure in get_phys_addr(),
since I dropped the earlier patch that would have provided it]
Message-id: 20220822152741.1617527-14-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the use of regime_is_secure from pmsav8_mpu_lookup,
passing the new parameter to the lookup instead.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-13-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the use of regime_is_secure from v8m_security_lookup,
passing the new parameter to the lookup instead.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-12-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This can be made redundant with result->page_size, by moving the basic
set of page_size from get_phys_addr_pmsav8. We still need to overwrite
page_size when v8m_security_lookup signals a subpage.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-11-richard.henderson@linaro.org
[PMM: Update a comment that used to refer to is_subpage]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-10-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-9-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-8-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-7-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-6-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-5-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-4-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Combine 5 output pointer arguments from get_phys_addr
into a single struct. Adjust all callers.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220822152741.1617527-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When requested, the alignment for VLD4.32 is 8 and not 16.
See ARM documentation about VLD4 encoding:
ebytes = 1 << UInt(size);
if size == '10' then
alignment = if a == '0' then 1 else 8;
else
alignment = if a == '0' then 1 else 4*ebytes;
Signed-off-by: Clément Chigot <chigot@adacore.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220914105058.2787404-1-chigot@adacore.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update the ID registers for TCG's '-cpu max' to report a FEAT_PMUv3p5
compliant PMU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-11-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
With FEAT_PMUv3p5, the event counters are now 64 bit, rather than 32
bit. (Previously, only the cycle counter could be 64 bit, and other
event counters were always 32 bits). For any given event counter,
whether the overflow event is noted for overflow from bit 31 or from
bit 63 is controlled by a combination of PMCR.LP, MDCR_EL2.HLP and
MDCR_EL2.HPMN.
Implement the 64-bit event counter handling. We choose to make our
counters always 64 bits, and mask out the top 32 bits on read or
write of PMXEVCNTR for CPUs which don't have FEAT_PMUv3p5.
(Note that the changes to pmenvcntr_op_start() and
pmenvcntr_op_finish() bring their logic closer into line with that of
pmccntr_op_start() and pmccntr_op_finish(), which already had to cope
with the overflow being either at 32 or 64 bits.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-10-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
FEAT_PMUv3p5 introduces new bits which disable the cycle
counter from counting:
* MDCR_EL2.HCCD disables the counter when in EL2
* MDCR_EL3.SCCD disables the counter when Secure
Add the code to support these bits.
(Note that there is a third documented counter-disable
bit, MDCR_EL3.MCCD, which disables the counter when in
EL3. This is not present until FEAT_PMUv3p7, so is
out of scope for now.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-9-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Our feature test functions that check the PMU version are named
isar_feature_{aa32,aa64,any}_pmu_8_{1,4}. This doesn't match the
current Arm ARM official feature names, which are FEAT_PMUv3p1 and
FEAT_PMUv3p4. Rename these functions to _pmuv3p1 and _pmuv3p4.
This commit was created with:
sed -i -e 's/pmu_8_/pmuv3p/g' target/arm/*.[ch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-8-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In pmccntr_op_finish() and pmevcntr_op_finish() we calculate the next
point at which we will get an overflow and need to fire the PMU
interrupt or set the overflow flag. We do this by calculating the
number of nanoseconds to the overflow event and then adding it to
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL). However, we don't check
whether that signed addition overflows, which can happen if the next
PMU interrupt would happen massively far in the future (250 years or
more).
Since QEMU assumes that "when the QEMU_CLOCK_VIRTUAL rolls over" is
"never", the sensible behaviour in this situation is simply to not
try to set the timer if it would be beyond that point. Detect the
overflow, and skip setting the timer in that case.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-7-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The logic in pmu_counter_enabled() for handling the 'prohibit event
counting' bits MDCR_EL2.HPMD and MDCR_EL3.SPME is written in a way
that assumes that EL2 is never Secure. This used to be true, but the
architecture now permits Secure EL2, and QEMU can emulate this.
Refactor the prohibit logic so that we effectively OR together
the various prohibit bits when they apply, rather than trying to
construct an if-else ladder where any particular state of the CPU
ends up in exactly one branch of the ladder.
This fixes the Secure EL2 case and also is a better structure for
adding the PMUv8.5 bits MDCR_EL2.HCCD and MDCR_EL3.SCCD.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-6-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The architecture requires that if PMCR.LC is set (for a 64-bit cycle
counter) then PMCR.D (which enables the clock divider so the counter
ticks every 64 cycles rather than every cycle) should be ignored. We
were always honouring PMCR.D; fix the bug so we correctly ignore it
in this situation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-5-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The PMU cycle and event counter infrastructure design requires that
operations on the PMU register fields are wrapped in pmu_op_start()
and pmu_op_finish() calls (or their more specific pmmcntr and
pmevcntr equivalents). This includes any changes to registers which
affect whether the counter should be enabled or disabled, but we
forgot to do this.
The effect of this bug is that in sequences like:
* disable the cycle counter (PMCCNTR) using the PMCNTEN register
* write a value such as 0xfffff000 to the PMCCNTR
* restart the counter by writing to PMCNTEN
the value written to the cycle counter is corrupted, and it starts
counting from the wrong place. (Essentially, we fail to record that
the QEMU_CLOCK_VIRTUAL timestamp when the counter should be considered
to have started counting is the point when PMCNTEN is written to enable
the counter.)
Add the necessary bracketing calls, so that updates to the various
registers which affect whether the PMU is counting are handled
correctly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-4-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
pmu_counter_mask() accidentally returns a value with bits [63:32]
set, because the expression it returns is evaluated as a signed value
that gets sign-extended to 64 bits. Force the whole expression to be
evaluated with 64-bit arithmetic with ULL suffixes.
The main effect of this bug was that a guest could write to the bits
in the high half of registers like PMCNTENSET_EL0 that are supposed
to be RES0.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-3-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
When the cycle counter overflows, we are intended to set bit 31 in PMOVSR
to indicate this. However a missing ULL suffix means that we end up
setting all of bits 63-31. Fix the bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822132358.3524971-2-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Fix a missing space before a comment terminator.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220819110052.2942289-7-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The architectural feature FEAT_ETS (Enhanced Translation
Synchronization) is a set of tightened guarantees about memory
ordering involving translation table walks:
* if memory access RW1 is ordered-before memory access RW2 then it
is also ordered-before any translation table walk generated by RW2
that generates a translation fault, address size fault or access
fault
* TLB maintenance on non-exec-permission translations is guaranteed
complete after a DSB (ie it does not need the context
synchronization event that you have to have if you don’t have
FEAT_ETS)
For QEMU’s implementation we don’t reorder translation table walk
accesses, and we guarantee to finish the TLB maintenance as soon as
the TLB op is done (the tlb_flush functions will complete at the end
of the TLB, and TLB ops always end the TB because they’re sysreg
writes).
So we’re already compliant and all we need to do is say so in the ID
registers for the 'max' CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220819110052.2942289-6-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In Armv8.6, a new AArch32 ID register ID_DFR1 is defined; implement
it. We don't have any CPUs with features that they need to advertise
here yet, but plumbing in the ID register gives it the right name
when debugging and will help in future when we do add a CPU that
has non-zero ID_DFR1 fields.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220819110052.2942289-5-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In Armv8.6 a new AArch32 ID register ID_MMFR5 is defined.
Implement this; we want to be able to use it to report to
the guest that we implement FEAT_ETS.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220819110052.2942289-4-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The code that reads the AArch32 ID registers from KVM in
kvm_arm_get_host_cpu_features() does so almost but not quite in
encoding order. Move the read of ID_PFR2 down so it's really in
encoding order.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220819110052.2942289-3-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In the AArch32 ID register scheme, coprocessor registers with
encoding cp15, 0, c0, c{0-7}, {0-7} are all in the space covered by
what in v6 and v7 was called the "CPUID scheme", and are supposed to
RAZ if they're not allocated to a specific ID register. For our
pre-v8 CPUs we get this right, because the regdefs in
id_pre_v8_midr_cp_reginfo[] cover these RAZ requirements. However
for v8 we failed to put in the necessary patterns to cover this, so
we end up UNDEFing on everything we didn't have an ID register for.
This is a problem because in Armv8 some encodings in 0, c0, c3, {0-7}
are now being used for new ID registers, and guests might thus start
trying to read them. (We already have one of these: ID_PFR2.)
For v8 CPUs, we already have regdefs for 0, c0, c{0-2}, {0-7} (that
is, the space is completely allocated with no reserved spaces). Add
entries to v8_idregs[] covering 0, c0, c3, {0-7}:
* c3, {0-2} is the reserved AArch32 space corresponding to the
AArch64 MVFR[012]_EL1
* c3, {3,5,6,7} are reserved RAZ for both AArch32 and AArch64
(in fact some of these are given defined meanings in Armv8.6,
but we don't implement them yet)
* c3, 4 is ID_PFR2 (already defined)
We then programmatically add RAZ patterns for AArch32 for
0, c0, c{4..15}, {0-7}:
* c4-c7 are unused, and not shared with AArch64 (these
are the encodings corresponding to where the AArch64
specific ID registers live in the system register space)
* c8-c15 weren't required to RAZ in v6/v7, but v8 extends
the AArch32 reserved-should-RAZ space to cover these;
the equivalent area of the AArch64 sysreg space is not
defined as must-RAZ
Note that the architecture allows some registers in this space
to return an UNKNOWN value; we always return 0.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220819110052.2942289-2-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Add cortex A35 core and enable it for virt board.
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Joe Komlodi <komlodi@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220819002015.1663247-1-wuhaotsh@google.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Honour the commandline -semihosting-config userspace=on option,
instead of never permitting userspace semihosting calls in system
emulation mode, by passing the correct value to the is_userspace
argument of semihosting_enabled(), instead of manually checking and
always forbidding semihosting if the guest is in userspace and this
isn't the linux-user build.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822141230.3658237-3-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Currently our semihosting implementations generally prohibit use of
semihosting calls in system emulation from the guest userspace. This
is a very long standing behaviour justified originally "to provide
some semblance of security" (since code with access to the
semihosting ABI can do things like read and write arbitrary files on
the host system). However, it is sometimes useful to be able to run
trusted guest code which performs semihosting calls from guest
userspace, notably for test code. Add a command line suboption to
the existing semihosting-config option group so that you can
explicitly opt in to semihosting from guest userspace with
-semihosting-config userspace=on
(There is no equivalent option for the user-mode emulator, because
there by definition all code runs in userspace and has access to
semihosting already.)
This commit adds the infrastructure for the command line option and
adds a bool 'is_user' parameter to the function
semihosting_userspace_enabled() that target code can use to check
whether it should be permitting the semihosting call for userspace.
It mechanically makes all the callsites pass 'false', so they
continue checking "is semihosting enabled in general". Subsequent
commits will make each target that implements semihosting honour the
userspace=on option by passing the correct value and removing
whatever "don't do this for userspace" checking they were doing by
hand.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220822141230.3658237-2-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Pass these along to translator_loop -- pc may be used instead
of tb->pc, and host_pc is currently unused. Adjust all targets
at one time.
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Tested-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The newly added neoverse-n1 CPU has ID register values which indicate
the presence of the Statistical Profiling Extension, because the real
hardware has this feature. QEMU's TCG emulation does not yet
implement SPE, though (not even as a minimal stub implementation), so
guests will crash if they try to use it because the SPE system
registers don't exist.
Force ID_AA64DFR0_EL1.PMSVer to 0 in CPU realize for TCG, so that
we don't advertise to the guest a feature that doesn't exist.
(We could alternatively do this by editing the value that
aarch64_neoverse_n1_initfn() sets for this ID register, but
suppressing the field in realize means we won't re-introduce this bug
when we add other CPUs that have SPE in hardware, such as the
Neoverse-V1.)
An example of a non-booting guest is current mainline Linux (5.19),
when booting in EL2 on the virt board (ie with -machine
virtualization=on).
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Message-id: 20220811131127.947334-1-peter.maydell@linaro.org
When the user queries CPU models via QMP there is a 'deprecated' flag
present, however, this is not done for the CLI '-cpu help' command.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The test for the IF block indicates no ID registers are exposed, much
less host support for SVE. Move the SVE probe into the ELSE block.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220726045828.53697-4-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Because we weren't setting this flag, our probe of ID_AA64ZFR0
was always returning zero. This also obviates the adjustment
of ID_AA64PFR0, which had sanitized the SVE field.
The effects of the bug are not visible, because the only thing that
ID_AA64ZFR0 is used for within qemu at present is tcg translation.
The other tests for SVE within KVM are via ID_AA64PFR0.SVE.
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220726045828.53697-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Indication for support for SVE will not depend on whether we
perform the query on the main kvm_state or the temp vcpu.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220726045828.53697-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Some files wrongly contain the same word twice in a row.
One of them should be removed or replaced.
Message-Id: <20220722145859.1952732-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220707163720.1421716-5-berrange@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
perror() is designed to append the decoded errno value to a
string. This, however, only makes sense if we called something that
actually sets errno prior to that.
For the callers that check for split irqchip support that is not the
case, and we end up with confusing error messages that end in
"success". Use error_report() instead.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20220728142446.438177-1-cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In commit 7390e0e9ab, we added support for SME loads and stores.
Unlike SVE loads and stores, these include handling of 128-bit
elements. The SME load/store functions call down into the existing
sve_cont_ldst_elements() function, which uses the element size MO_*
value as an index into the pred_esz_masks[] array. Because this code
path now has to handle MO_128, we need to add an extra element to the
array.
This bug was spotted by Coverity because it meant we were reading off
the end of the array.
Resolves: Coverity CID 1490539, 1490541, 1490543, 1490544, 1490545,
1490546, 1490548, 1490549, 1490550, 1490551, 1490555, 1490557,
1490558, 1490560, 1490561, 1490563
Fixes: 7390e0e9ab ("target/arm: Implement SME LD1, ST1")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220718100144.3248052-1-peter.maydell@linaro.org
The architecture requires that for faults on loads and stores which
do writeback, the syndrome information does not have the ISS
instruction syndrome information (i.e. ISV is 0). We got this wrong
for the load and store instructions covered by disas_ldst_reg_imm9().
Calculate iss_valid correctly so that if the insn is a writeback one
it is false.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1057
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220715123323.1550983-1-peter.maydell@linaro.org
In regime_tcr() we return the appropriate TCR register for the
translation regime. For Secure EL2, we return the VSTCR_EL2 value,
but in this translation regime some fields that control behaviour are
in VTCR_EL2. When this code was originally written (as the comment
notes), QEMU didn't care about any of those fields, but we have since
added support for features such as LPA2 which do need the values from
those fields.
Synthesize a TCR value by merging in the relevant VTCR_EL2 fields to
the VSTCR_EL2 value.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1103
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-8-peter.maydell@linaro.org
Change the representation of the TCR_EL* registers in the CPU state
struct from struct TCR to uint64_t. This allows us to drop the
custom vmsa_ttbcr_raw_write() function, moving the "enforce RES0"
checks to their more usual location in the writefn
vmsa_ttbcr_write(). We also don't need the resetfn any more.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-7-peter.maydell@linaro.org
Change the representation of the VSTCR_EL2 and VTCR_EL2 registers in
the CPU state struct from struct TCR to uint64_t.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-6-peter.maydell@linaro.org
We have a bug in our handling of accesses to the AArch32 VTCR
register on big-endian hosts: we were not adjusting the part of the
uint64_t field within TCR that the generated code would access. That
can be done with offsetoflow32(), by using an ARM_CP_STATE_BOTH cpreg
struct, or by defining a full set of read/write/reset functions --
the various other TCR cpreg structs used one or another of those
strategies, but for VTCR we did not, so on a big-endian host VTCR
accesses would touch the wrong half of the register.
Use offsetoflow32() in the VTCR register struct. This works even
though the field in the CPU struct is currently a struct TCR, because
the first field in that struct is the uint64_t raw_tcr.
None of the other TCR registers have this bug -- either they are
AArch64 only, or else they define resetfn, writefn, etc, and
expect to be passed the full struct pointer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-5-peter.maydell@linaro.org
The only caller of regime_tcr() is now regime_tcr_value(); fold the
two together, and use the shorter and more natural 'regime_tcr'
name for the new function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-4-peter.maydell@linaro.org
In get_level1_table_address(), instead of using precalculated values
of mask and base_mask from the TCR struct, calculate them directly
(in the same way we currently do in vmsa_ttbcr_raw_write() to
populate the TCR struct fields).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-3-peter.maydell@linaro.org
The regime_tcr() function returns a pointer to a struct TCR
corresponding to the TCR controlling a translation regime. The
struct TCR has the raw value of the register, plus two fields mask
and base_mask which are used as a small optimization in the case of
32-bit short-descriptor lookups. Almost all callers of regime_tcr()
only want the raw register value. Define and use a new
regime_tcr_value() function which returns only the raw 64-bit
register value.
This is a preliminary to removing the 32-bit short descriptor
optimization -- it only saves a handful of bit operations, which is
tiny compared to the overhead of doing a page table walk at all, and
the TCR struct is awkward and makes fixing
https://gitlab.com/qemu-project/qemu/-/issues/1103 unnecessarily
difficult.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220714132303.1287193-2-peter.maydell@linaro.org
The documentation for PROT_MTE says that it cannot be cleared
by mprotect. Further, the implementation of the VM_ARCH_CLEAR bit,
contains PROT_BTI confiming that bit should be cleared.
Introduce PAGE_TARGET_STICKY to allow target/arch/cpu.h to control
which bits may be reset during page_set_flags. This is sort of the
opposite of VM_ARCH_CLEAR, but works better with qemu's PAGE_* bits
that are separate from PROT_* bits.
Reported-by: Vitaly Buka <vitalybuka@google.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220711031420.17820-1-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We were only checking for SVE disabled and not taking into
account PSTATE.SM to check SME disabled, which resulted in
vectors being incorrectly truncated.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220713045848.217364-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When PSTATE.SM, VL = SVL even if SVE is disabled.
This is visible in kselftest ssve-test.
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220713045848.217364-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Enable SME, TPIDR2_EL0, and FA64 if supported by the cpu.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220708151540.18136-45-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There's no reason to set CPACR_EL1.ZEN if SVE disabled.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220708151540.18136-44-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Note that SME remains effectively disabled for user-only,
because we do not yet set CPACR_EL1.SMEN. This needs to
wait until the kernel ABI is implemented.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220708151540.18136-33-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We can handle both exception entry and exception return by
hooking into aarch64_sve_change_el.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220708151540.18136-32-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
