This adds the ISSI SPI flash support. The number of dummy cycles in
fast read, fast read dual output and fast read quad output commands
is currently using the default 8. Likewise, the same default value
is used for fast read dual/quad I/O command. Per the datasheet [1],
the number of dummy cycles is configurable, but this is not modeled
at present.
For flash whose size is larger than 16 MiB, the sequence of 3-byte
address along with EXTADD bit in the bank address register (BAR) is
not supported. We assume that guest software always uses op codes
with 4-byte address sequence. Fortunately, this is the case for both
U-Boot and Linux spi-nor drivers.
QPI (Quad Peripheral Interface) that supports 2-cycle instruction
has different default values for dummy cycles of fast read family
commands, and is unsupported at the time being.
[1] http://www.issi.com/WW/pdf/25LP-WP256.pdf
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This was only required for the pc-1.0 and earlier machine types.
Now that these have been removed, we can also drop the corresponding
code from the FDC device.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20210203171832.483176-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Linux blkfront expects both "discard-granularity" and
"discard-alignment" present on xenbus in order to properly enable the
feature, not exposing "discard-alignment" left some Linux blkfront
versions with a broken discard setup. This has also been addressed in
Linux with:
https://lore.kernel.org/lkml/20210118151528.81668-1-roger.pau@citrix.com/T/#u
Fix QEMU to report a "discard-alignment" of 0, in order for it to work
with older Linux frontends.
Reported-by: Arthur Borsboom <arthurborsboom@gmail.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Message-Id: <20210118153330.82324-1-roger.pau@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
nvme_ns_realize passes errp to nvme_register_namespaces, but then try to
prepend errp with local_err.
Just remove the local_err and use errp directly.
Fixes: 15d024d4aa ("hw/block/nvme: split setup and register for namespace")
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Current QEMU HEAD nvme.c does not compile with the default GCC 5.4
on a Ubuntu 16.04 host:
hw/block/nvme.c:3242:9: error: ‘result’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
trace_pci_nvme_getfeat_vwcache(result ? "enabled" : "disabled");
^
hw/block/nvme.c:3150:14: note: ‘result’ was declared here
uint32_t result;
^
Explicitly initialize the result to fix it.
Fixes: aa5e55e3b0 ("hw/block/nvme: open code for volatile write cache")
Fixes: Coverity CID 1446371
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Moving namespace registration to the nvme-ns realization function had
the unintended side-effect of breaking legacy namespace registration.
Fix this.
Fixes: 15d024d4aa ("hw/block/nvme: split setup and register for namespace")
Reported-by: Alexander Graf <agraf@csgraf.de>
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Alexander Graf <agraf@csgraf.de>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Refactor the zone write check logic such that the most "meaningful"
error is returned first. That is, first, if the zone is not writable,
return an appropriate status code for that. Then, make sure we are
actually writing at the write pointer and finally check that we do not
cross the zone write boundary. This aligns with the "priority" of status
codes for zone read checks.
Also add a couple of additional descriptive trace events and remove an
always true assert.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
When a zone append is processed the controller checks that validity of
the write before assigning the LBA to the append command. This causes
the boundary check to be wrong.
Fix this by checking the write *after* assigning the LBA. Remove the
append special case from the nvme_check_zone_write and open code it in
nvme_do_write, assigning the slba when basic sanity checks have been
performed. Then check the validity of the resulting write like any other
write command.
In the process, also fix a missing endianness conversion for the zone
append ALBA.
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The actual parameter name is 'cross_read' rather than 'cross_zone_read'.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Change status checks to align with the existing style and remove the
explicit check against NVME_SUCCESS.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Currently, no features are saveable, so the current check is not wrong,
but add a check against the feature capabilities to make sure this will
not regress if saveable features are added later.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Only enable DULBE if the namespace supports it.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
If a user assigns a backing device with less capacity than the size of a
single zone, the namespace capacity will be reported as zero and the
kernel will silently fail to allocate the namespace.
This patch errors out in case that the backing device cannot accomodate
at least a single zone.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
[k.jensen: small fixup in the error and commit message]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The controller now implements v1.4 and we can lift the restrictions on
CMB Data Pointer and Command Independent Locations Support (CDPCILS) and
CMB Data Pointer Mixed Locations Support (CDPMLS) since the device
really does not care about mixed host/cmb pointers in those cases.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
With the new CMB logic in place, bump the implemented specification
version to v1.4 by default.
This requires adding the setting the CNTRLTYPE field and modifying the
VWC field since 0x00 is no longer a valid value for bits 2:1.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Implement v1.4 logic for configuring the Controller Memory Buffer. By
default, the v1.4 scheme will be used (CMB must be explicitly enabled by
the host), so drivers that only support v1.3 will not be able to use the
CMB anymore.
To retain the v1.3 behavior, set the boolean 'legacy-cmb' nvme device
parameter.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Padmakar Kalghatgi <p.kalghatgi@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for the PMRMSCL and PMRMSCU MMIO registers. This allows
adding RDS/WDS support for PMR as well.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Naveen Nagar <naveen.n1@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The PMR should not be enabled at boot up. Disable the PMR MemoryRegion
initially and implement MMIO for PMRCTL, allowing the host to enable the
PMR explicitly.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The controller registers are initially zero. Remove the redundant
zeroing.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Use the correct field names.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
With BAR 4 now free to use, allow PMR and CMB to be enabled
simultaneously.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
In the interest of supporting both CMB and PMR to be enabled on the same
device, move the MSI-X table and pending bit array out of BAR 4 and into
BAR 0.
This is a simplified version of the patch contributed by Andrzej
Jakowski (see [1]). Leaving the CMB at offset 0 removes the need for
changes to CMB address mapping code.
[1]: https://lore.kernel.org/qemu-devel/20200729220107.37758-3-andrzej.jakowski@linux.intel.com/
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This patch sets CMBS bit in controller capabilities register when user
configures NVMe driver with CMB support, so capabilites are correctly
reported to guest OS.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@linux.intel.com>
Reviewed-by: Maxim Levitsky <mlevitsky@gmail.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
64 bit registers like ASQ and ACQ should be writable by both a hi/lo 32
bit write combination as well as a plain 64 bit write. The spec does not
define ordering on the hi/lo split, but the code currently assumes that
the low order bits are written first. Additionally, the code does not
consider that another address might already have been written into the
register, causing the OR'ing to result in a bad address.
Fix this by explicitly overwriting only the low or high order bits for
32 bit writes.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add the size of the mmio read/write to the trace event.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
During smart critical warning injection by setting property from QMP
command, also try to trigger asynchronous event.
Suggested by Keith, if a event has already been raised, there is no
need to enqueue the duplicate event any more.
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
[k.jensen: fix typo in commit message]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
There is a very low probability that hitting physical NVMe disk
hardware critical warning case, it's hard to write & test a monitor
agent service.
For debugging purposes, add a new 'smart_critical_warning' property
to emulate this situation.
The orignal version of this change is implemented by adding a fixed
property which could be initialized by QEMU command line. Suggested
by Philippe & Klaus, rework like current version.
Test with this patch:
1, change smart_critical_warning property for a running VM:
#virsh qemu-monitor-command nvme-upstream '{ "execute": "qom-set",
"arguments": { "path": "/machine/peripheral-anon/device[0]",
"property": "smart_critical_warning", "value":16 } }'
2, run smartctl in guest
#smartctl -H -l error /dev/nvme0n1
=== START OF SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
- volatile memory backup device has failed
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The zone write pointer is unconditionally advanced, even for write
faults. Make sure that the zone is always transitioned to Full if the
write pointer reaches zone capacity.
Cc: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_ns_setup() finally does not have nothing to do with NvmeCtrl
instance.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
In NVMe, namespace is being attached to process I/O. We register NVMe
namespace to a controller via nvme_register_namespace() during
nvme_ns_setup(). This is main reason of receiving NvmeCtrl object
instance to this function to map the namespace to a controller.
To make namespace instance more independent, it should be split into two
parts: setup and register. This patch split them into two differnt
parts, and finally nvme_ns_setup() does not have nothing to do with
NvmeCtrl instance at all.
This patch is a former patch to introduce NVMe subsystem scheme to the
existing design especially for multi-path. In that case, it should be
split into two to make namespace independent from a controller.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Removed no longer used aregument NvmeCtrl object in nvme_ns_init_blk().
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Volatile Write Cache(VWC) feature is set in nvme_ns_setup() in the
initial time. This feature is related to block device backed, but this
feature is controlled in controller level via Set/Get Features command.
This patch removed dependency between nvme and nvme-ns to manage the VWC
flag value. Also, it open coded the Get Features for VWC to check all
namespaces attached to the controller, and if false detected, return
directly false.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
[k.jensen: report write cache preset if present on ANY namespace]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_ns_init_zoned() has no use for given NvmeCtrl object.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
TP 4053 says (in section 2.3.1.1) -
... if a Zone Append command specifies a ZSLBA that is not the lowest
logical block address in that zone, then the controller shall abort
that command with a status code of Invalid Field In Command.
In the code, Zone Invalid Write is returned instead, fix this.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_io_cmd already checks if the namespace supports the Zone Append
command, so the removed check is dead code.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Add missing string representations for a couple of new commands.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
The zoned command set specification states that "All logical blocks in a
zone *shall* be marked as deallocated when [the zone is reset]". Since
the device guarantees 0x00 to be read from deallocated blocks we have to
issue a pwrite_zeroes since we cannot be sure that a discard will do
anything. But typically, this will be achieved with an efficient
unmap/discard operation.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Align with existing style and use a typedef for header-file enums.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Implicitly and explicitly opended zones are always bulk processed
together, so merge the two processing masks.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
A shutdown is only about flushing stuff. It is the host that should
delete any queues, so do not perform a reset here.
Also, on shutdown, make sure that the PMR is flushed if in use.
Fixes: 368f4e752cf9 ("hw/block/nvme: Process controller reset and shutdown differently")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Tested-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
The device uses the BDRV_BLOCK_ZERO flag to determine the "deallocated"
status of logical blocks. Since the zoned namespaces command set
specification defines that logical blocks SHALL be marked as deallocated
when the zone is in the Empty or Offline states, DULBE can only be
supported if the zone size is a multiple of the calculated deallocation
granularity (reported in NPDG) which depends on the underlying block
device cluster size (if applicable) or the configured
discard_granularity.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit 1c0c2163aa ("hw/block/nvme: verify msix_init_exclusive_bar()
return value") had the unintended effect of breaking support on
several platforms not supporting MSI-X.
Still check for errors, but only report that MSI-X is unsupported
instead of bailing out.
Fixes: 1c0c2163aa ("hw/block/nvme: verify msix_init_exclusive_bar() return value")
Fixes: fbf2e5375e ("hw/block/nvme: Verify msix_vector_use() returned value")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Added brief descriptions of the new device properties that are
now available to users to configure features of Zoned Namespace
Command Set in the emulator.
This patch is for documentation only, no functionality change.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Zone Descriptor Extension is a label that can be assigned to a zone.
It can be set to an Empty zone and it stays assigned until the zone
is reset.
This commit adds a new optional module property,
"zoned.descr_ext_size". Its value must be a multiple of 64 bytes.
If this value is non-zero, it becomes possible to assign extensions
of that size to any Empty zones. The default value for this property
is 0, therefore setting extensions is disabled by default.
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add two module properties, "zoned.max_active" and "zoned.max_open"
to control the maximum number of zones that can be active or open.
Once these variables are set to non-default values, these limits are
checked during I/O and Too Many Active or Too Many Open command status
is returned if they are exceeded.
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The emulation code has been changed to advertise NVM Command Set when
"zoned" device property is not set (default) and Zoned Namespace
Command Set otherwise.
Define values and structures that are needed to support Zoned
Namespace Command Set (NVMe TP 4053) in PCI NVMe controller emulator.
Define trace events where needed in newly introduced code.
In order to improve scalability, all open, closed and full zones
are organized in separate linked lists. Consequently, almost all
zone operations don't require scanning of the entire zone array
(which potentially can be quite large) - it is only necessary to
enumerate one or more zone lists.
Handlers for three new NVMe commands introduced in Zoned Namespace
Command Set specification are added, namely for Zone Management
Receive, Zone Management Send and Zone Append.
Device initialization code has been extended to create a proper
configuration for zoned operation using device properties.
Read/Write command handler is modified to only allow writes at the
write pointer if the namespace is zoned. For Zone Append command,
writes implicitly happen at the write pointer and the starting write
pointer value is returned as the result of the command. Write Zeroes
handler is modified to add zoned checks that are identical to those
done as a part of Write flow.
Subsequent commits in this series add ZDE support and checks for
active and open zone limits.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Hans Holmberg <hans.holmberg@wdc.com>
Signed-off-by: Ajay Joshi <ajay.joshi@wdc.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Matias Bjorling <matias.bjorling@wdc.com>
Signed-off-by: Aravind Ramesh <aravind.ramesh@wdc.com>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Adam Manzanares <adam.manzanares@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Many CNS commands have "allocated" command variants. These include
a namespace as long as it is allocated, that is a namespace is
included regardless if it is active (attached) or not.
While these commands are optional (they are mandatory for controllers
supporting the namespace attachment command), our QEMU implementation
is more complete by actually providing support for these CNS values.
However, since our QEMU model currently does not support the namespace
attachment command, these new allocated CNS commands will return the
same result as the active CNS command variants.
The reason for not hooking up this command completely is because the
NVMe specification requires the namespace management command to be
supported if the namespace attachment command is supported.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Define the structures and constants required to implement
Namespace Types support.
Namespace Types introduce a new command set, "I/O Command Sets",
that allows the host to retrieve the command sets associated with
a namespace. Introduce support for the command set and enable
detection for the NVM Command Set.
The new workflows for identify commands rely heavily on zero-filled
identify structs. E.g., certain CNS commands are defined to return
a zero-filled identify struct when an inactive namespace NSID
is supplied.
Add a helper function in order to avoid code duplication when
reporting zero-filled identify structures.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This log page becomes necessary to implement to allow checking for
Zone Append command support in Zoned Namespace Command Set.
This commit adds the code to report this log page for NVM Command
Set only. The parts that are specific to zoned operation will be
added later in the series.
All incoming admin and i/o commands are now only processed if their
corresponding support bits are set in this log. This provides an
easy way to control what commands to support and what not to
depending on set CC.CSS.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Move write processing to nvme_do_write() that now handles both WRITE
and WRITE ZEROES. Both nvme_write() and nvme_write_zeroes() become
inline helper functions.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The majority of code in nvme_rw() is becoming read- or write-specific.
Move these parts to two separate handlers, nvme_read() and nvme_write()
to make the code more readable and to remove multiple is_write checks
that has been present in the i/o path.
This is a refactoring patch, no change in functionality.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
In NVMe 1.4, a namespace must report an ID descriptor of UUID type
if it doesn't support EUI64 or NGUID. Add a new namespace property,
"uuid", that provides the user the option to either specify the UUID
explicitly or have a UUID generated automatically every time a
namespace is initialized.
Suggested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Controller reset ans subsystem shutdown are handled very much the same
in the current code, but some of the steps should be different in these
two cases.
Introduce two new functions, nvme_reset_ctrl() and nvme_shutdown_ctrl(),
to separate some portions of the code from nvme_clear_ctrl(). The steps
that are made different between reset and shutdown are that BAR.CC is not
reset to zero upon the shutdown and namespace data is flushed to
backing storage as a part of shutdown handling, but not upon reset.
Suggested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Commit 37712e00b1 ("hw/block/nvme: factor out pmr setup") changed the
control flow such that the CAP register is erronously cleared after
nvme_init_pmr() has configured it. Since the entire NvmeCtrl structure
is zero-filled initially, there is no need for the explicit clearing, so
just remove it.
Fixes: 37712e00b1 ("hw/block/nvme: factor out pmr setup")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Add the Compare command.
This implementation uses a bounce buffer to read in the data from
storage and then compare with the host supplied buffer.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: rebased]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for the Dataset Management command and the Deallocate
attribute. Deallocation results in discards being sent to the underlying
block device. Whether of not the blocks are actually deallocated is
affected by the same factors as Write Zeroes (see previous commit).
format | discard | dsm (512B) dsm (4KiB) dsm (64KiB)
--------------------------------------------------------
qcow2 ignore n n n
qcow2 unmap n n y
raw ignore n n n
raw unmap n y y
Again, a raw format and 4KiB LBAs are preferable.
In order to set the Namespace Preferred Deallocate Granularity and
Alignment fields (NPDG and NPDA), choose a sane minimum discard
granularity of 4KiB. If we are using a passthru device supporting
discard at a 512B granularity, user should set the discard_granularity
property explicitly. NPDG and NPDA will also account for the
cluster_size of the block driver if required (i.e. for QCOW2).
See NVM Express 1.3d, Section 6.7 ("Dataset Management command").
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for reporting the Deallocated or Unwritten Logical Block
Error (DULBE).
Rely on the block status flags reported by the block layer and consider
any block with the BDRV_BLOCK_ZERO flag to be deallocated.
Multiple factors affect when a Write Zeroes command result in
deallocation of blocks.
* the underlying file system block size
* the blockdev format
* the 'discard' and 'logical_block_size' parameters
format | discard | wz (512B) wz (4KiB) wz (64KiB)
-----------------------------------------------------
qcow2 ignore n n y
qcow2 unmap n n y
raw ignore n y y
raw unmap n y y
So, this works best with an image in raw format and 4KiB LBAs, since
holes can then be punched on a per-block basis (this assumes a file
system with a 4kb block size, YMMV). A qcow2 image, uses a cluster size
of 64KiB by default and blocks will only be marked deallocated if a full
cluster is zeroed or discarded. However, this *is* consistent with the
spec since Write Zeroes "should" deallocate the block if the Deallocate
attribute is set and "may" deallocate if the Deallocate attribute is not
set. Thus, we always try to deallocate (the BDRV_REQ_MAY_UNMAP flag is
always set).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add a new function, nvme_aio_err, to handle errors resulting from AIOs
and use this from the callbacks.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
nvme_check_bounds has no use of the NvmeCtrl parameter; remove it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Currently, blk_is_read_only() tells whether a given BlockBackend can
only be used in read-only mode because its root node is read-only. Some
callers actually try to answer a slightly different question: Is the
BlockBackend configured to be writable, by taking write permissions on
the root node?
This can differ, for example, for CD-ROM devices which don't take write
permissions, but may be backed by a writable image file. scsi-cd allows
write requests to the drive if blk_is_read_only() returns false.
However, the write request will immediately run into an assertion
failure because the write permission is missing.
This patch introduces separate functions for both questions.
blk_supports_write_perm() answers the question whether the block
node/image file can support writable devices, whereas blk_is_writable()
tells whether the BlockBackend is currently configured to be writable.
All calls of blk_is_read_only() are converted to one of the two new
functions.
Fixes: https://bugs.launchpad.net/bugs/1906693
Cc: qemu-stable@nongnu.org
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210118123448.307825-2-kwolf@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
- minor resource leak fixes in qemu-nbd
- ensure proper aio context when nbd server uses iothreads
- iotest refactorings in preparation for rewriting ./check to be more
flexible, and preparing for more nbd server reconnect features
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEccLMIrHEYCkn0vOqp6FrSiUnQ2oFAmAI5sMACgkQp6FrSiUn
Q2rmQwf+Jmlsn8s0tdeeOhv6mp8ZSyvr2/x1/daGHkzZqhoL7m/4kJLP4p/u8uTV
XzXyXt7MKvHKd8UvKB6VsN6z75RJvi7y8pKpOQA96t08hjWuAcVtivKnyZd6MTwj
zeKsmrE8LAuMjHvmsrtrmRqCSdaVeFPb3qC6bvJ+WEiXJIMiXybF7lccPvR7WWjR
2FcyraZJgnlKrQv1i8M1++Px5W14jhOacAMUNAdVzNiYpu4tq6PTk9giq1/GULCz
xVYGHqoTFYy7Slj7xKQJuOwGNLMwL+F9x7/6wRFhKxjutc0/Po1lSfbaNe8q147H
p9jtDT9/OuTlQf7qpqqyQnASABDgaA==
=XW+E
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ericb/tags/pull-nbd-2021-01-20' into staging
nbd patches for 2021-01-20
- minor resource leak fixes in qemu-nbd
- ensure proper aio context when nbd server uses iothreads
- iotest refactorings in preparation for rewriting ./check to be more
flexible, and preparing for more nbd server reconnect features
# gpg: Signature made Thu 21 Jan 2021 02:28:19 GMT
# gpg: using RSA key 71C2CC22B1C4602927D2F3AAA7A16B4A2527436A
# gpg: Good signature from "Eric Blake <eblake@redhat.com>" [full]
# gpg: aka "Eric Blake (Free Software Programmer) <ebb9@byu.net>" [full]
# gpg: aka "[jpeg image of size 6874]" [full]
# Primary key fingerprint: 71C2 CC22 B1C4 6029 27D2 F3AA A7A1 6B4A 2527 436A
* remotes/ericb/tags/pull-nbd-2021-01-20:
iotests.py: qemu_io(): reuse qemu_tool_pipe_and_status()
iotests.py: fix qemu_tool_pipe_and_status()
iotests/264: fix style
iotests: define group in each iotest
iotests/294: add shebang line
iotests: make tests executable
iotests: fix some whitespaces in test output files
iotests/303: use dot slash for qcow2.py running
iotests/277: use dot slash for nbd-fault-injector.py running
nbd/server: Quiesce coroutines on context switch
block: Honor blk_set_aio_context() context requirements
qemu-nbd: Fix a memleak in nbd_client_thread()
qemu-nbd: Fix a memleak in qemu_nbd_client_list()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The documentation for bdrv_set_aio_context_ignore() states this:
* The caller must own the AioContext lock for the old AioContext of bs, but it
* must not own the AioContext lock for new_context (unless new_context is the
* same as the current context of bs).
As blk_set_aio_context() makes use of this function, this rule also
applies to it.
Fix all occurrences where this rule wasn't honored.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Sergio Lopez <slp@redhat.com>
Message-Id: <20201214170519.223781-2-slp@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
As per POSIX specification of limits.h [1], OS libc may define
PAGE_SIZE in limits.h.
To prevent collosion of definition, we rename PAGE_SIZE here.
[1]: https://pubs.opengroup.org/onlinepubs/7908799/xsh/limits.h.html
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210118063808.12471-5-jiaxun.yang@flygoat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Auto Address Increment (AAI) Word-Program is a special command of
SST flashes. AAI-WP allows multiple bytes of data to be programmed
without re-issuing the next sequential address location.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 1608688825-81519-2-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When write is disabled, the write to flash should be avoided
in flash_write8().
Fixes: 82a2499011 ("m25p80: Initial implementation of SPI flash device")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Message-id: 1608688825-81519-1-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This commit is the result of running the timer-del-timer-free.cocci
script on the whole source tree.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201215154107.3255-4-peter.maydell@linaro.org
The function will be moved to common QOM code, as it is not
specific to TYPE_DEVICE anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20201211220529.2290218-31-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Every single qdev property setter function manually checks
dev->realized. We can just check dev->realized inside
qdev_property_set() instead.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20201211220529.2290218-24-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the property types and property macros implemented in
qdev-properties-system.c to a new qdev-properties-system.h
header.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This is the QEMU equivalent of this Linux commit (but 7 years later):
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=f7025a43a9da2
The MTD subsystem has its own small museum of ancient NANDs
in a form of the CONFIG_MTD_NAND_MUSEUM_IDS configuration option.
The museum contains stone age NANDs with 256 bytes pages, as well
as iron age NANDs with 512 bytes per page and up to 8MiB page size.
It is with great sorrow that I inform you that the museum is being
decommissioned. The MTD subsystem is out of budget for Kconfig
options and already has too many of them, and there is a general
kernel trend to simplify the configuration menu.
We remove the stone age exhibits along with closing the museum,
but some of the iron age ones are transferred to the regular NAND
depot. Namely, only those which have unique device IDs are
transferred, and the ones which have conflicting device IDs are
removed.
The machine using this device are:
- axis-dev88
- tosa (via tc6393xb_init)
- spitz based (akita, borzoi, terrier)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201214002620.342384-1-f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* gdbstub: Correct misparsing of vCont C/S requests
* openrisc: Move pic_cpu code into CPU object proper
* nios2: Move IIC code into CPU object proper
* Improve reporting of ROM overlap errors
* xlnx-versal: Add USB support
* hw/misc/zynq_slcr: Avoid #DIV/0! error
* Numonyx: Fix dummy cycles and check for SPI mode on cmds
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAl/YwVIZHHBldGVyLm1h
eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3lOpD/9FjasMvZqYeanyNlv+4Swk
4MFeYouIzXKSFu9tj5eDTHzN1TJl5iSwhkIcr9NBqxppuv2eqzxfWWMEfCZ06pxz
BR2HoSlSLUih8cKpu40cQg0TTMEOGEOV9RAHtt8vSGE0FesoiXG2ORUPcxm3NxbN
l9XZ1x3Yb5ZLqVZViFjlZ5gXnTzJ//uPEzbl7N9+pa0mXDKvmvwAl19DLmF6N2Jj
D+gmrLGeEbkJ358RGO/VF7r/1bOkrhwKrb8MzeqFRmjIqaOGbGqs/71+amiSjS8n
hC1HKf6KQOLrklMVaYg1pRxHLbHpQR+haeeX4Xt9jxx8EUrwXojlyaD8p4V9Hcu8
L5haTIBhPrnTkUfHZYL0qYkqRpzbNq97oX2Gmk967FfsZME5fxNa3kS6zM0GkIBx
YKghaZtFInAFODUbG1hHdUc+WbvfQDhj/mBQ6wWw669vYpoab/3nfVq8YVoupVM/
RntcqpBfqtGgPzuJ2dJEEsm6QlK4SZaGlmPkz542OzcHxw3SgeqkbIuDW/CtNI+b
c5PgX0C2S2AnFAAHURnsXdqt6+O01FZqOU7SCLjmwrBrpDG69lum+JLCqXFe9iMW
XgrTrxyPIcz5+Bv63AqKcm6rpcQs5ekwmLLEjT0OJtr+5ef9MeRil0aChj1j4i+2
H/82yKR4JWW1egEvTJhskQ==
=lHZA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20201215' into staging
target-arm queue:
* gdbstub: Correct misparsing of vCont C/S requests
* openrisc: Move pic_cpu code into CPU object proper
* nios2: Move IIC code into CPU object proper
* Improve reporting of ROM overlap errors
* xlnx-versal: Add USB support
* hw/misc/zynq_slcr: Avoid #DIV/0! error
* Numonyx: Fix dummy cycles and check for SPI mode on cmds
# gpg: Signature made Tue 15 Dec 2020 13:59:46 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20201215:
hw/block/m25p80: Fix Numonyx fast read dummy cycle count
hw/block/m25p80: Check SPI mode before running some Numonyx commands
hw/block/m25p80: Fix when VCFG XIP bit is set for Numonyx
hw/block/m25p80: Make Numonyx config field names more accurate
hw/misc/zynq_slcr: Avoid #DIV/0! error
arm: xlnx-versal: Connect usb to virt-versal
usb: xlnx-usb-subsystem: Add xilinx usb subsystem
usb: Add DWC3 model
usb: Add versal-usb2-ctrl-regs module
elf_ops.h: Be more verbose with ROM blob names
elf_ops.h: Don't truncate name of the ROM blobs we create
hw/core/loader.c: Improve reporting of ROM overlap errors
hw/core/loader.c: Track last-seen ROM in rom_check_and_register_reset()
target/nios2: Use deposit32() to update ipending register
target/nios2: Move nios2_check_interrupts() into target/nios2
target/nios2: Move IIC code into CPU object proper
target/openrisc: Move pic_cpu code into CPU object proper
hw/openrisc/openrisc_sim: Abstract out "get IRQ x of CPU y"
hw/openrisc/openrisc_sim: Use IRQ splitter when connecting IRQ to multiple CPUs
gdbstub: Correct misparsing of vCont C/S requests
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make the code more generic and not specific to TYPE_DEVICE.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com> #s390 parts
Acked-by: Paul Durrant <paul@xen.org>
Message-Id: <20201211220529.2290218-10-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some Numonyx flash commands cannot be executed in DIO and QIO mode, such as
trying to do DPP or DOR when in QIO mode.
Signed-off-by: Joe Komlodi <komlodi@xilinx.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Message-id: 1605568264-26376-4-git-send-email-komlodi@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
VCFG XIP is set (disabled) when the NVCFG XIP bits are all set (disabled).
Signed-off-by: Joe Komlodi <komlodi@xilinx.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Message-id: 1605568264-26376-3-git-send-email-komlodi@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The previous naming of the configuration registers made it sound like that if
the bits were set the settings would be enabled, while the opposite is true.
Signed-off-by: Joe Komlodi <komlodi@xilinx.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Message-id: 1605568264-26376-2-git-send-email-komlodi@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In order to use inclusive terminology, rename SSI 'slave' as
'peripheral', following the specification resolution:
https://www.oshwa.org/a-resolution-to-redefine-spi-signal-names/
Patch created mechanically using:
$ sed -i s/SSISlave/SSIPeripheral/ $(git grep -l SSISlave)
$ sed -i s/SSI_SLAVE/SSI_PERIPHERAL/ $(git grep -l SSI_SLAVE)
$ sed -i s/ssi-slave/ssi-peripheral/ $(git grep -l ssi-slave)
$ sed -i s/ssi_slave/ssi_peripheral/ $(git grep -l ssi_slave)
$ sed -i s/ssi_create_slave/ssi_create_peripheral/ \
$(git grep -l ssi_create_slave)
Then in VMStateDescription vmstate_ssi_peripheral we restored
the "SSISlave" migration stream name (to avoid breaking migration).
Finally the following files have been manually tweaked:
- hw/ssi/pl022.c
- hw/ssi/xilinx_spips.c
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201012124955.3409127-4-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The category of the nand device is not set, put it into the 'storage'
category.
Signed-off-by: Gan Qixin <ganqixin@huawei.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201112125824.763182-4-ganqixin@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
There is no "version 2" of the "Lesser" General Public License.
It is either "GPL version 2.0" or "Lesser GPL version 2.1".
This patch replaces all occurrences of "Lesser GPL version 2" with
"Lesser GPL version 2.1" in comment section.
Signed-off-by: Chetan Pant <chetan4windows@gmail.com>
Message-Id: <20201023123034.19609-1-chetan4windows@gmail.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
[thuth: Fixed subject]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Since 7f0f1acedf ("hw/block/nvme: support multiple namespaces"), the
namespaces member of NvmeCtrl is no longer a dynamically allocated
array. Remove the free.
Fixes: 7f0f1acedf ("hw/block/nvme: support multiple namespaces")
Reported-by: Coverity (CID 1436131)
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20201104102248.32168-4-its@irrelevant.dk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
nvme_map_sgl_data erroneously uses the sgls member of NvmeIdNs as a
uint16_t.
Reported-by: Coverity (CID 1436129)
Fixes: cba0a8a344 ("hw/block/nvme: add support for scatter gather lists")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20201104102248.32168-3-its@irrelevant.dk>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Max Reitz <mreitz@redhat.com>
Virtqueue has split and packed, so before setting inflight,
you need to inform the back-end virtqueue format.
Signed-off-by: Jin Yu <jin.yu@intel.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20201103123617.28256-1-jin.yu@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This reverts commit adb29c0273.
The commit broke -device vhost-user-blk-pci because the
vhost_dev_prepare_inflight() function it introduced segfaults in
vhost_dev_set_features() when attempting to access struct vhost_dev's
vdev pointer before it has been assigned.
To reproduce the segfault simply launch a vhost-user-blk device with the
contrib vhost-user-blk device backend:
$ build/contrib/vhost-user-blk/vhost-user-blk -s /tmp/vhost-user-blk.sock -r -b /var/tmp/foo.img
$ build/qemu-system-x86_64 \
-device vhost-user-blk-pci,id=drv0,chardev=char1,addr=4.0 \
-object memory-backend-memfd,id=mem,size=1G,share=on \
-M memory-backend=mem,accel=kvm \
-chardev socket,id=char1,path=/tmp/vhost-user-blk.sock
Segmentation fault (core dumped)
Cc: Jin Yu <jin.yu@intel.com>
Cc: Raphael Norwitz <raphael.norwitz@nutanix.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20201102165709.232180-1-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----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=s4KC
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/nvme/tags/pull-nvme-20201102' into staging
nvme pull 2 Nov 2020
# gpg: Signature made Mon 02 Nov 2020 15:20:30 GMT
# gpg: using RSA key DBC11D2D373B4A3755F502EC625156610A4F6CC0
# gpg: Good signature from "Keith Busch <kbusch@kernel.org>" [unknown]
# gpg: aka "Keith Busch <keith.busch@gmail.com>" [unknown]
# gpg: aka "Keith Busch <keith.busch@intel.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: DBC1 1D2D 373B 4A37 55F5 02EC 6251 5661 0A4F 6CC0
* remotes/nvme/tags/pull-nvme-20201102: (30 commits)
hw/block/nvme: fix queue identifer validation
hw/block/nvme: fix create IO SQ/CQ status codes
hw/block/nvme: fix prp mapping status codes
hw/block/nvme: report actual LBA data shift in LBAF
hw/block/nvme: add trace event for requests with non-zero status code
hw/block/nvme: add nsid to get/setfeat trace events
hw/block/nvme: reject io commands if only admin command set selected
hw/block/nvme: support for admin-only command set
hw/block/nvme: validate command set selected
hw/block/nvme: support per-namespace smart log
hw/block/nvme: fix log page offset check
hw/block/nvme: remove pointless rw indirection
hw/block/nvme: update nsid when registered
hw/block/nvme: change controller pci id
pci: allocate pci id for nvme
hw/block/nvme: support multiple namespaces
hw/block/nvme: refactor identify active namespace id list
hw/block/nvme: add support for sgl bit bucket descriptor
hw/block/nvme: add support for scatter gather lists
hw/block/nvme: harden cmb access
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Virtqueue has split and packed, so before setting inflight,
you need to inform the back-end virtqueue format.
Signed-off-by: Jin Yu <jin.yu@intel.com>
Message-Id: <20200910134851.7817-1-jin.yu@intel.com>
Acked-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The nvme_check_{sq,cq} functions check if the given queue identifer is
valid *and* that the queue exists. Thus, the function return value
cannot simply be inverted to check if the identifer is valid and that
the queue does *not* exist.
Replace the call with an OR'ed version of the checks.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Replace the Invalid Field in Command with the Invalid PRP Offset status
code in the nvme_create_{cq,sq} functions. Also, allow PRP1 to be
address 0x0.
Also replace the Completion Queue Invalid status code returned in
nvme_create_cq when the the queue identifier is invalid with the Invalid
Queue Identifier. The Completion Queue Invalid status code is
exclusively for indicating that the completion queue identifer given
when creating a submission queue is invalid.
See NVM Express v1.3d, Section 5.3 ("Create I/O Completion Queue
command") and 5.4("Create I/O Submission Queue command").
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Address 0 is not an invalid address. Remove those invalikd checks.
Unaligned PRP2 and PRP list entries should result in Invalid PRP Offset
status code and not Invalid Field. Fix that.
See NVMe Express v1.3d, Section 4.3 ("Physical Region Page Entry and
List").
Suggested-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Calculate the data shift value to report based on the set value of
logical_block_size device property.
In the process, use a local variable to calculate the LBA format
index instead of the hardcoded value 0. This makes the code more
readable and it will make it easier to add support for multiple LBA
formats in the future.
Signed-off-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
If a command results in a non-zero status code, trace it.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Include the namespace id in the pci_nvme_{get,set}feat trace events.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
If the host sets CC.CSS to 111b, all commands submitted to I/O queues
should be completed with status Invalid Command Opcode.
Note that this is technically a v1.4 feature, but it does not hurt to
implement before we finally bump the reported version implemented.
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Fail to start the controller if the user requests a command set that the
controller does not support.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Let the user specify a specific namespace if they want to get access
stats for a specific namespace.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Return error if the requested offset starts after the size of the log
being returned. Also, move the check for earlier in the function so
we're not doing unnecessary calculations.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed- by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
The code switches on the opcode to invoke a function specific to that
opcode. There's no point in consolidating back to a common function that
just switches on that same opcode without any actual common code.
Restore the opcode specific behavior without going back through another
level of switches.
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
If the user does not specify an nsid parameter on the nvme-ns device,
nvme_register_namespace will find the first free namespace id and assign
that.
This fix makes sure the assigned id is saved.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
There are two reasons for changing this:
1. The nvme device currently uses an internal Intel device id.
2. Since commits "nvme: fix write zeroes offset and count" and "nvme:
support multiple namespaces" the controller device no longer has
the quirks that the Linux kernel think it has.
As the quirks are applied based on pci vendor and device id, change
them to get rid of the quirks.
To keep backward compatibility, add a new 'use-intel-id' parameter to
the nvme device to force use of the Intel vendor and device id. This is
off by default but add a compat property to set this for 5.1 machines
and older. If a 5.1 machine is booted (or the use-intel-id parameter is
explicitly set to true), the Linux kernel will just apply these
unnecessary quirks:
1. NVME_QUIRK_IDENTIFY_CNS which says that the device does not support
anything else than values 0x0 and 0x1 for CNS (Identify Namespace
and Identify Namespace). With multiple namespace support, this just
means that the kernel will "scan" namespaces instead of using
"Active Namespace ID list" (CNS 0x2).
2. NVME_QUIRK_DISABLE_WRITE_ZEROES. The nvme device started out with a
broken Write Zeroes implementation which has since been fixed in
commit 9d6459d21a ("nvme: fix write zeroes offset and count").
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
This adds support for multiple namespaces by introducing a new 'nvme-ns'
device model. The nvme device creates a bus named from the device name
('id'). The nvme-ns devices then connect to this and registers
themselves with the nvme device.
This changes how an nvme device is created. Example with two namespaces:
-drive file=nvme0n1.img,if=none,id=disk1
-drive file=nvme0n2.img,if=none,id=disk2
-device nvme,serial=deadbeef,id=nvme0
-device nvme-ns,drive=disk1,bus=nvme0,nsid=1
-device nvme-ns,drive=disk2,bus=nvme0,nsid=2
The drive property is kept on the nvme device to keep the change
backward compatible, but the property is now optional. Specifying a
drive for the nvme device will always create the namespace with nsid 1.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Prepare to support inactive namespaces.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
This adds support for SGL descriptor type 0x1 (bit bucket descriptor).
See the NVM Express v1.3d specification, Section 4.4 ("Scatter Gather
List (SGL)").
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
For now, support the Data Block, Segment and Last Segment descriptor
types.
See NVM Express 1.3d, Section 4.4 ("Scatter Gather List (SGL)").
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Since the controller has only supported PRPs so far it has not been
required to check the ending address (addr + len - 1) of the CMB access
for validity since it has been guaranteed to be in range of the CMB.
This changes when the controller adds support for SGLs (next patch), so
add that check.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Make the default request status NVME_SUCCESS so only error status codes
have to be set.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
This pulls block layer aio submission/completion to common functions.
For completions, additionally map an AIO error to the Unrecovered Read
and Write Fault status codes.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add the symbolic command name to the pci_nvme_{io,admin}_cmd and
pci_nvme_rw trace events.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
The raw NLB field is a 16 bit value, so use le16_to_cpu instead of
le32_to_cpu and cast to uint32_t before incrementing the value to not
wrap around.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Add the nvme_l2b helper and use it for converting NLB and SLBA to byte
counts and offsets.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Style fixes.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Handling DMA errors gracefully is required for the device to pass the
block/011 test ("disable PCI device while doing I/O") in the blktests
suite.
With this patch the device sets the Controller Fatal Status bit in the
CSTS register when failing to read from a submission queue or writing to
a completion queue; expecting the host to reset the controller.
If DMA errors occur at any other point in the execution of the command
(say, while mapping the PRPs), the command is aborted with a Data
Transfer Error status code.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Fix a typo in the sq doorbell trace event.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
As the 'timestamp' variable is declared as a 48-bit bitfield,
we do not need to wrap the sum result.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20201002075716.1657849-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
vhost-user devices can get a disconnect in the middle of the VHOST-USER
handshake on the migration start. If disconnect event happened right
before sending next VHOST-USER command, then the vhost_dev_set_log()
call in the vhost_migration_log() function will return error. This error
will lead to the assert() and close the QEMU migration source process.
For the vhost-user devices the disconnect event should not break the
migration process, because:
- the device will be in the stopped state, so it will not be changed
during migration
- if reconnect will be made the migration log will be reinitialized as
part of reconnect/init process:
#0 vhost_log_global_start (listener=0x563989cf7be0)
at hw/virtio/vhost.c:920
#1 0x000056398603d8bc in listener_add_address_space (listener=0x563989cf7be0,
as=0x563986ea4340 <address_space_memory>)
at softmmu/memory.c:2664
#2 0x000056398603dd30 in memory_listener_register (listener=0x563989cf7be0,
as=0x563986ea4340 <address_space_memory>)
at softmmu/memory.c:2740
#3 0x0000563985fd6956 in vhost_dev_init (hdev=0x563989cf7bd8,
opaque=0x563989cf7e30, backend_type=VHOST_BACKEND_TYPE_USER,
busyloop_timeout=0)
at hw/virtio/vhost.c:1385
#4 0x0000563985f7d0b8 in vhost_user_blk_connect (dev=0x563989cf7990)
at hw/block/vhost-user-blk.c:315
#5 0x0000563985f7d3f6 in vhost_user_blk_event (opaque=0x563989cf7990,
event=CHR_EVENT_OPENED)
at hw/block/vhost-user-blk.c:379
Update the vhost-user-blk device with the internal started_vu field which
will be used for initialization (vhost_user_blk_start) and clean up
(vhost_user_blk_stop). This additional flag in the VhostUserBlk structure
will be used to track whether the device really needs to be stopped and
cleaned up on a vhost-user level.
The disconnect event will set the overall VHOST device (not vhost-user) to
the stopped state, so it can be used by the general vhost_migration_log
routine.
Such approach could be propogated to the other vhost-user devices, but
better idea is just to make the same connect/disconnect code for all the
vhost-user devices.
This migration issue was slightly discussed earlier:
- https://lists.gnu.org/archive/html/qemu-devel/2020-05/msg01509.html
- https://lists.gnu.org/archive/html/qemu-devel/2020-05/msg05241.html
Signed-off-by: Dima Stepanov <dimastep@yandex-team.ru>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <9fbfba06791a87813fcee3e2315f0b904cc6789a.1599813294.git.dimastep@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fuzzing discovered that virtqueue_unmap_sg() is being called on modified
req->in/out_sg iovecs. This means dma_memory_map() and
dma_memory_unmap() calls do not have matching memory addresses.
Fuzzing discovered that non-RAM addresses trigger a bug:
void address_space_unmap(AddressSpace *as, void *buffer, hwaddr len,
bool is_write, hwaddr access_len)
{
if (buffer != bounce.buffer) {
^^^^^^^^^^^^^^^^^^^^^^^
A modified iov->iov_base is no longer recognized as a bounce buffer and
the wrong branch is taken.
There are more potential bugs: dirty memory is not tracked correctly and
MemoryRegion refcounts can be leaked.
Use the new iov_discard_undo() API to restore elem->in/out_sg before
virtqueue_push() is called.
Fixes: 827805a249 ("virtio-blk: Convert VirtIOBlockReq.out to structrue")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Buglink: https://bugs.launchpad.net/qemu/+bug/1890360
Message-Id: <20200917094455.822379-3-stefanha@redhat.com>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of scripts/cleanup-trace-events.pl. Funnies
requiring manual post-processing:
* accel/tcg/cputlb.c trace points are in trace-events.
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* hw/tpm/tpm_spapr.c uses pseudo trace point tpm_spapr_show_buffer to
guard debug code.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* linux-user/trace-events abbreviates a tedious list of filenames to
*/signal.c.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200806141334.3646302-5-armbru@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
-----BEGIN PGP SIGNATURE-----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=ZQHA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20200901' into staging
Various fixes of Aspeed machines :
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
# gpg: Signature made Tue 01 Sep 2020 13:39:20 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20200901:
hw: add a number of SPI-flash's of m25p80 family
arm: aspeed: add strap define `25HZ` of AST2500
aspeed/smc: Open AHB window of the second chip of the AST2600 FMC controller
aspeed/sdmc: Simplify calculation of RAM bits
aspeed/sdmc: Allow writes to unprotected registers
aspeed/sdmc: Perform memory training
ftgmac100: Improve software reset
ftgmac100: Fix integer overflow in ftgmac100_do_tx()
ftgmac100: Check for invalid len and address before doing a DMA transfer
ftgmac100: Change interrupt status when a DMA error occurs
ftgmac100: Fix interrupt status "Packet moved to RX FIFO"
ftgmac100: Fix interrupt status "Packet transmitted on ethernet"
ftgmac100: Fix registers that can be read
aspeed/sdhci: Fix reset sequence
aspeed/smc: Fix max_slaves of the legacy SMC device
aspeed/smc: Fix MemoryRegionOps definition
hw/arm/aspeed: Add board model for Supermicro X11 BMC
aspeed/scu: Fix valid access size on AST2400
m25p80: Add support for n25q512ax3
m25p80: Return the JEDEC ID twice for mx25l25635e
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since nvme_map_prp always operate on the request-scoped qsg/iovs, just
pass a single pointer to the NvmeRequest instead of two for each of the
qsg and iov.
Suggested-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Since clean up of the request qsg/iov is now always done post-use, there
is no need to use a stack-allocated qsg/iov in nvme_dma_prp.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Always destroy the request qsg/iov at the end of request use.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Instead of passing around the NvmeNamespace and the NvmeCmd, add them as
members in the NvmeRequest structure.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
The NVM Express specification generally uses 'zeroes' and not 'zeros',
so let us align with it.
Cc: Fam Zheng <fam@euphon.net>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Add 'mdts' device parameter to control the Maximum Data Transfer Size of
the controller and check that it is respected.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Hoist bounds checking into its own function and check for wrap-around.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Before this patch the device already supported PRP lists in the CMB, but
it did not check for the validity of it nor announced the support in the
Identify Controller data structure LISTS field.
If some of the PRPs in a PRP list are in the CMB, then ALL entries must
be there. This patch makes sure that requirement is verified as well as
properly announcing support for PRP lists in the CMB.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Introduce the nvme_map helper to remove some noise in the main nvme_rw
function.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Refactor the nvme_dma_{read,write}_prp functions into a common function
taking a DMADirection parameter.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Make sure the request iov is destroyed before reuse; fixing a memory
leak.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Remove the has_sg member from NvmeRequest since it's redundant.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
The QSG isn't always initialized, so accounting could be wrong. Issue a
call to blk_acct_start instead with the size taken from the QSG or IOV
depending on the kind of I/O.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Add nvme_map_addr, nvme_map_addr_cmb and nvme_addr_to_cmb helpers and
use them in nvme_map_prp.
This fixes a bug where in the case of a CMB transfer, the device would
map to the buffer with a wrong length.
Fixes: b2b2b67a00 ("nvme: Add support for Read Data and Write Data in CMBs.")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Andrzej Jakowski <andrzej.jakowski@linux.intel.com>
This is preparatory to subsequent patches that change how QSGs/IOVs are
handled. It is important that the qsg and iov members of the NvmeRequest
are initially zeroed.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
The SUBNQN field is mandatory in NVM Express 1.3.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-18-its@irrelevant.dk>
Support returning Command Sequence Error if Set Features on Number of
Queues is called after queues have been created.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-17-its@irrelevant.dk>
Reject the nsid broadcast value (0xffffffff) and 0xfffffffe in the
Active Namespace ID list.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-16-its@irrelevant.dk>
Since we are not providing the NGUID or EUI64 fields, we must support
the Namespace UUID. We do not have any way of storing a persistent
unique identifier, so conjure up a UUID that is just the namespace id.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-15-its@irrelevant.dk>
0xffff is not an allowed value for NCQR and NSQR in Set Features on
Number of Queues.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-14-its@irrelevant.dk>
Since the device does not have any persistent state storage, no
features are "saveable" and setting the Save (SV) field in any Set
Features command will result in a Feature Identifier Not Saveable status
code.
Similarly, if the Select (SEL) field is set to request saved values, the
devices will (as it should) return the default values instead.
Since this also introduces "Supported Capabilities", the nsid field is
now also checked for validity wrt. the feature being get/set'ed.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-13-its@irrelevant.dk>
If the write cache is disabled with a Set Features command, flush it if
currently enabled.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-11-its@irrelevant.dk>
The NvmeFeatureVal does not belong with the spec-related data structures
in include/block/nvme.h that is shared between the block-level nvme
driver and the emulated nvme device.
Move it into the nvme device specific header file as it is the only
user of the structure. Also, remove the unused members.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-10-its@irrelevant.dk>
Add support for the Asynchronous Event Request command. Required for
compliance with NVMe revision 1.3d. See NVM Express 1.3d, Section 5.2
("Asynchronous Event Request command").
Mostly imported from Keith's qemu-nvme tree. Modified with a max number
of queued events (controllable with the aer_max_queued device
parameter). The spec states that the controller *should* retain
events, so we do best effort here.
Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-9-its@irrelevant.dk>
Add support for the Get Log Page command and basic implementations of
the mandatory Error Information, SMART / Health Information and Firmware
Slot Information log pages.
In violation of the specification, the SMART / Health Information log
page does not persist information over the lifetime of the controller
because the device has no place to store such persistent state.
Note that the LPA field in the Identify Controller data structure
intentionally has bit 0 cleared because there is no namespace specific
information in the SMART / Health information log page.
Required for compliance with NVMe revision 1.3d. See NVM Express 1.3d,
Section 5.14 ("Get Log Page command").
Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-8-its@irrelevant.dk>
Mark firmware slot 1 as read-only and only support that slot.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-7-its@irrelevant.dk>
It might seem weird to implement this feature for an emulated device,
but it is mandatory to support and the feature is useful for testing
asynchronous event request support, which will be added in a later
patch.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-6-its@irrelevant.dk>
Required for compliance with NVMe revision 1.3d. See NVM Express 1.3d,
Section 5.1 ("Abort command").
The Abort command is a best effort command; for now, the device always
fails to abort the given command.
Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-5-its@irrelevant.dk>
Add various additional tracing and streamline nvme_identify_ns and
nvme_identify_nslist (they do not need to repeat the command, it is
already in the trace name).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-4-its@irrelevant.dk>
Fix a missing cpu_to conversion by moving conversion to just before
returning instead.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-3-its@irrelevant.dk>
Add missing fields in the Identify Controller and Identify Namespace
data structures to bring them in line with NVMe v1.3.
This also adds data structures and defines for SGL support which
requires a couple of trivial changes to the nvme block driver as well.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Fam Zheng <fam@euphon.net>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-2-its@irrelevant.dk>
Simplify the NVMe emulated device by aligning the I/O BAR to 4 KiB.
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200630110429.19972-5-philmd@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
At some point the URL changed, update it to avoid other
developers to search for it.
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200630110429.19972-2-philmd@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Support a following SPI flashes:
* mx66l51235f
* mt25ql512ab
Signed-off-by: Igor Kononenko <i.kononenko@yadro.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200811203724.20699-1-i.kononenko@yadro.com>
Message-Id: <20200819100956.2216690-22-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The mx25l25635e returns the JEDEC ID twice when issuing a RDID command :
[ 2.512027] aspeed-smc 1e630000.spi: reading JEDEC ID C2:20:19:C2:20:19
This can break some firmware testing for this condition on the
supermicrox11-bmc machine.
Reported-by: Erik Smit <erik.lucas.smit@gmail.com>
Message-Id: <20200819100956.2216690-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Remove superfluous breaks, as there is a "return" before them.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1594631126-36631-1-git-send-email-wang.yi59@zte.com.cn>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Currently we have a SWIM typedef and a SWIM type checking macro,
but OBJECT_DECLARE* would transform the SWIM macro into a
function, and the function name would conflict with the SWIM
typedef name.
Rename the struct and typedef to "Swim". This will make future
conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-50-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Automatically size the number of request virtqueues to match the number
of vCPUs. This ensures that completion interrupts are handled on the
same vCPU that submitted the request. No IPI is necessary to complete
an I/O request and performance is improved. The maximum number of MSI-X
vectors and virtqueues limit are respected.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20200818143348.310613-8-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Automatically size the number of virtio-blk-pci request virtqueues to
match the number of vCPUs. Other transports continue to default to 1
request virtqueue.
A 1:1 virtqueue:vCPU mapping ensures that completion interrupts are
handled on the same vCPU that submitted the request. No IPI is
necessary to complete an I/O request and performance is improved. The
maximum number of MSI-X vectors and virtqueues limit are respected.
Performance improves from 78k to 104k IOPS on a 32 vCPU guest with 101
virtio-blk-pci devices (ioengine=libaio, iodepth=1, bs=4k, rw=randread
with NVMe storage).
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Message-Id: <20200818143348.310613-7-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
object_get_canonical_path_component() returns a malloced copy of a
property name on success, null on failure.
19 of its 25 callers immediately free the returned copy.
Change object_get_canonical_path_component() to return the property
name directly. Since modifying the name would be wrong, adjust the
return type to const char *.
Drop the free from the 19 callers become simpler, add the g_strdup()
to the other six.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200714160202.3121879-4-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
If we want to check error after errp-function call, we need to
introduce local_err and then propagate it to errp. Instead, use
the ERRP_GUARD() macro, benefits are:
1. No need of explicit error_propagate call
2. No need of explicit local_err variable: use errp directly
3. ERRP_GUARD() leaves errp as is if it's not NULL or
&error_fatal, this means that we don't break error_abort
(we'll abort on error_set, not on error_propagate)
If we want to add some info to errp (by error_prepend() or
error_append_hint()), we must use the ERRP_GUARD() macro.
Otherwise, this info will not be added when errp == &error_fatal
(the program will exit prior to the error_append_hint() or
error_prepend() call). No such cases are being fixed here.
This commit is generated by command
sed -n '/^X86 Xen CPUs$/,/^$/{s/^F: //p}' MAINTAINERS | \
xargs git ls-files | grep '\.[hc]$' | \
xargs spatch \
--sp-file scripts/coccinelle/errp-guard.cocci \
--macro-file scripts/cocci-macro-file.h \
--in-place --no-show-diff --max-width 80
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reported-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200707165037.1026246-9-armbru@redhat.com>
[ERRP_AUTO_PROPAGATE() renamed to ERRP_GUARD(), and
auto-propagated-errp.cocci to errp-guard.cocci. Commit message
tweaked again.]
If we want to check error after errp-function call, we need to
introduce local_err and then propagate it to errp. Instead, use
the ERRP_GUARD() macro, benefits are:
1. No need of explicit error_propagate call
2. No need of explicit local_err variable: use errp directly
3. ERRP_GUARD() leaves errp as is if it's not NULL or
&error_fatal, this means that we don't break error_abort
(we'll abort on error_set, not on error_propagate)
If we want to add some info to errp (by error_prepend() or
error_append_hint()), we must use the ERRP_GUARD() macro.
Otherwise, this info will not be added when errp == &error_fatal
(the program will exit prior to the error_append_hint() or
error_prepend() call). No such cases are being fixed here.
This commit is generated by command
sed -n '/^Parallel NOR Flash devices$/,/^$/{s/^F: //p}' \
MAINTAINERS | \
xargs git ls-files | grep '\.[hc]$' | \
xargs spatch \
--sp-file scripts/coccinelle/errp-guard.cocci \
--macro-file scripts/cocci-macro-file.h \
--in-place --no-show-diff --max-width 80
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reported-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200707165037.1026246-5-armbru@redhat.com>
[ERRP_AUTO_PROPAGATE() renamed to ERRP_GUARD(), and
auto-propagated-errp.cocci to errp-guard.cocci. Commit message
tweaked again.]
Convert
visit_type_FOO(v, ..., &ptr, &err);
...
if (err) {
...
}
to
visit_type_FOO(v, ..., &ptr, errp);
...
if (!ptr) {
...
}
for functions that set @ptr to non-null / null on success / error.
Eliminate error_propagate() that are now unnecessary. Delete @err
that are now unused.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-40-armbru@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. The previous two commits did that for sufficiently simple
cases with Coccinelle. Do it for several more manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-37-armbru@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The previous commit enables conversion of
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., errp)) {
...
}
for QOM functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun = {
object_apply_global_props, object_initialize_child_with_props,
object_initialize_child_with_propsv, object_property_get,
object_property_get_bool, object_property_parse, object_property_set,
object_property_set_bool, object_property_set_int,
object_property_set_link, object_property_set_qobject,
object_property_set_str, object_property_set_uint, object_set_props,
object_set_propv, user_creatable_add_dict,
user_creatable_complete, user_creatable_del
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-29-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
The previous commit enables conversion of
visit_foo(..., &err);
if (err) {
...
}
to
if (!visit_foo(..., errp)) {
...
}
for visitor functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun =~ "check_list|input_type_enum|lv_start_struct|lv_type_bool|lv_type_int64|lv_type_str|lv_type_uint64|output_type_enum|parse_type_bool|parse_type_int64|parse_type_null|parse_type_number|parse_type_size|parse_type_str|parse_type_uint64|print_type_bool|print_type_int64|print_type_null|print_type_number|print_type_size|print_type_str|print_type_uint64|qapi_clone_start_alternate|qapi_clone_start_list|qapi_clone_start_struct|qapi_clone_type_bool|qapi_clone_type_int64|qapi_clone_type_null|qapi_clone_type_number|qapi_clone_type_str|qapi_clone_type_uint64|qapi_dealloc_start_list|qapi_dealloc_start_struct|qapi_dealloc_type_anything|qapi_dealloc_type_bool|qapi_dealloc_type_int64|qapi_dealloc_type_null|qapi_dealloc_type_number|qapi_dealloc_type_str|qapi_dealloc_type_uint64|qobject_input_check_list|qobject_input_check_struct|qobject_input_start_alternate|qobject_input_start_list|qobject_input_start_struct|qobject_input_type_any|qobject_input_type_bool|qobject_input_type_bool_keyval|qobject_input_type_int64|qobject_input_type_int64_keyval|qobject_input_type_null|qobject_input_type_number|qobject_input_type_number_keyval|qobject_input_type_size_keyval|qobject_input_type_str|qobject_input_type_str_keyval|qobject_input_type_uint64|qobject_input_type_uint64_keyval|qobject_output_start_list|qobject_output_start_struct|qobject_output_type_any|qobject_output_type_bool|qobject_output_type_int64|qobject_output_type_null|qobject_output_type_number|qobject_output_type_str|qobject_output_type_uint64|start_list|visit_check_list|visit_check_struct|visit_start_alternate|visit_start_list|visit_start_struct|visit_type_.*";
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-19-armbru@redhat.com>
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20200619091905.21676-6-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
acpi aml generator needs this, but it is in floppy code now
so we can make the function static.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20200619091905.21676-5-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
DSDT change: isa device order changes in case MI1 (ipmi) is present.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200619091905.21676-4-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qdev_prop_set_drive() can fail. None of the other qdev_prop_set_FOO()
can; they abort on error.
To clean up this inconsistency, rename qdev_prop_set_drive() to
qdev_prop_set_drive_err(), and create a qdev_prop_set_drive() that
aborts on error.
Coccinelle script to update callers:
@ depends on !(file in "hw/core/qdev-properties-system.c")@
expression dev, name, value;
symbol error_abort;
@@
- qdev_prop_set_drive(dev, name, value, &error_abort);
+ qdev_prop_set_drive(dev, name, value);
@@
expression dev, name, value, errp;
@@
- qdev_prop_set_drive(dev, name, value, errp);
+ qdev_prop_set_drive_err(dev, name, value, errp);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-14-armbru@redhat.com>
Deprecate
-global isa-fdc.driveA=...
-global isa-fdc.driveB=...
in favour of
-device floppy,unit=0,drive=...
-device floppy,unit=1,drive=...
Same for the other floppy controller devices.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20200622094227.1271650-7-armbru@redhat.com>
Helper function fdctrl_init_isa() is less than helpful: one of three
places creating "isa-fdc" devices use it. Open-code it there, and
drop the function.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-6-armbru@redhat.com>
The floppy controller devices desugar their drive properties into
floppy devices (since commit a92bd191a4 "fdc: Move qdev properties to
FloppyDrive", v2.8.0). This involves some bad magic in
fdctrl_connect_drives(), and exists for backward compatibility.
The functions for boards to create floppy controller devices
fdctrl_init_isa(), fdctrl_init_sysbus(), and sun4m_fdctrl_init()
desugar -drive if=floppy to these floppy controller drive properties.
If you use both -drive if=floppy (or its -fda / -fdb sugar) and
-global isa-fdc for the same floppy device, -global silently loses the
conflict, and both backends involved end up with the floppy device
frontend attached, as demonstrated by iotest 172 (see commit before
previous). This is wrong.
Desugar -drive if=floppy straight to floppy devices instead, with
helper fdctrl_init_drives(). The conflict now gets rejected cleanly:
first, fdctrl_connect_drives() creates the floppy for the controller's
property, then fdctrl_init_drives() attempts to create the floppy for
-drive if=floppy, but fails because the unit is already in use.
Output of iotest 172 changes in three ways:
1. The clash gets rejected.
2. In one test case, "info qtree" has the floppy devices swapped, and
"info block" has their QOM paths swapped. This is because the
floppy device for -fda now gets created after the one for -global
isa-fdc.driveB.
3. The error message for -global floppy.drive=floppy0 changes. Before
the patch, we set isa-fdc.driveA to -fda's block backend, then
create the floppy device for it, then move the backend from
isa-fdc.driveA to floppy.drive. Floppy creation fails when
applying -global floppy.drive=floppy0, because floppy0 is still
attached to isa-fdc. After the patch, we create the floppy for
-fda, then set its drive property to floppy0. Now floppy creation
succeeds, but setting the drive property fails, because -global
already set it. Yes, this is exasperatingly complicated.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200622094227.1271650-5-armbru@redhat.com>
Convert all size-related properties in BlockConf to 32bit. This will
accommodate bigger block sizes (in a followup patch). This also allows
to make them all accept size suffixes, either via DEFINE_PROP_BLOCKSIZE
or via DEFINE_PROP_SIZE32.
Also, since min_io_size is exposed to the guest by scsi and virtio-blk
devices as an uint16_t in units of logical blocks, introduce an
additional check in blkconf_blocksizes to prevent its silent truncation.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Message-Id: <20200528225516.1676602-7-rvkagan@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Several block device properties related to blocksize configuration must
be in certain relationship WRT each other: physical block must be no
smaller than logical block; min_io_size, opt_io_size, and
discard_granularity must be a multiple of a logical block.
To ensure these requirements are met, add corresponding consistency
checks to blkconf_blocksizes, adjusting its signature to communicate
possible error to the caller. Also remove the now redundant consistency
checks from the specific devices.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20200528225516.1676602-3-rvkagan@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The width of opt_io_size in virtio_blk_config is 32bit. However, it's
written with virtio_stw_p; this may result in value truncation, and on
big-endian systems with legacy virtio in completely bogus readings in
the guest.
Use the appropriate accessor to store it.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200528225516.1676602-2-rvkagan@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pass an Error to msix_init_exclusive_bar() and check it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20200609190333.59390-23-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Decouple the requested maximum number of ioqpairs (param max_ioqpairs)
from the number of MSI-X interrupt vectors by introducing a new
msix_qsize parameter and initialize MSI-X with that. This allows
emulating a device that has fewer vectors than I/O queue pairs and also
allows more than 2048 queue pairs. To keep the device behaving as
previously, use a msix_qsize default of 65 (default max_ioqpairs + 1).
This decoupling was actually suggested by Maxim some time ago in a
slightly different context, so adding a Suggested-by.
Suggested-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20200609190333.59390-22-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
msix_vector_use() returns -EINVAL on error. Assert it won't.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200609190333.59390-21-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-20-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200609190333.59390-19-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200609190333.59390-18-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-17-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-16-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
