This adds support for multiple namespaces by introducing a new 'nvme-ns'
device model. The nvme device creates a bus named from the device name
('id'). The nvme-ns devices then connect to this and registers
themselves with the nvme device.
This changes how an nvme device is created. Example with two namespaces:
-drive file=nvme0n1.img,if=none,id=disk1
-drive file=nvme0n2.img,if=none,id=disk2
-device nvme,serial=deadbeef,id=nvme0
-device nvme-ns,drive=disk1,bus=nvme0,nsid=1
-device nvme-ns,drive=disk2,bus=nvme0,nsid=2
The drive property is kept on the nvme device to keep the change
backward compatible, but the property is now optional. Specifying a
drive for the nvme device will always create the namespace with nsid 1.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Prepare to support inactive namespaces.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
This adds support for SGL descriptor type 0x1 (bit bucket descriptor).
See the NVM Express v1.3d specification, Section 4.4 ("Scatter Gather
List (SGL)").
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
For now, support the Data Block, Segment and Last Segment descriptor
types.
See NVM Express 1.3d, Section 4.4 ("Scatter Gather List (SGL)").
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Since the controller has only supported PRPs so far it has not been
required to check the ending address (addr + len - 1) of the CMB access
for validity since it has been guaranteed to be in range of the CMB.
This changes when the controller adds support for SGLs (next patch), so
add that check.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Make the default request status NVME_SUCCESS so only error status codes
have to be set.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
This pulls block layer aio submission/completion to common functions.
For completions, additionally map an AIO error to the Unrecovered Read
and Write Fault status codes.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add the symbolic command name to the pci_nvme_{io,admin}_cmd and
pci_nvme_rw trace events.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
The raw NLB field is a 16 bit value, so use le16_to_cpu instead of
le32_to_cpu and cast to uint32_t before incrementing the value to not
wrap around.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Add the nvme_l2b helper and use it for converting NLB and SLBA to byte
counts and offsets.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Style fixes.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Handling DMA errors gracefully is required for the device to pass the
block/011 test ("disable PCI device while doing I/O") in the blktests
suite.
With this patch the device sets the Controller Fatal Status bit in the
CSTS register when failing to read from a submission queue or writing to
a completion queue; expecting the host to reset the controller.
If DMA errors occur at any other point in the execution of the command
(say, while mapping the PRPs), the command is aborted with a Data
Transfer Error status code.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Fix a typo in the sq doorbell trace event.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
As the 'timestamp' variable is declared as a 48-bit bitfield,
we do not need to wrap the sum result.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20201002075716.1657849-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
vhost-user devices can get a disconnect in the middle of the VHOST-USER
handshake on the migration start. If disconnect event happened right
before sending next VHOST-USER command, then the vhost_dev_set_log()
call in the vhost_migration_log() function will return error. This error
will lead to the assert() and close the QEMU migration source process.
For the vhost-user devices the disconnect event should not break the
migration process, because:
- the device will be in the stopped state, so it will not be changed
during migration
- if reconnect will be made the migration log will be reinitialized as
part of reconnect/init process:
#0 vhost_log_global_start (listener=0x563989cf7be0)
at hw/virtio/vhost.c:920
#1 0x000056398603d8bc in listener_add_address_space (listener=0x563989cf7be0,
as=0x563986ea4340 <address_space_memory>)
at softmmu/memory.c:2664
#2 0x000056398603dd30 in memory_listener_register (listener=0x563989cf7be0,
as=0x563986ea4340 <address_space_memory>)
at softmmu/memory.c:2740
#3 0x0000563985fd6956 in vhost_dev_init (hdev=0x563989cf7bd8,
opaque=0x563989cf7e30, backend_type=VHOST_BACKEND_TYPE_USER,
busyloop_timeout=0)
at hw/virtio/vhost.c:1385
#4 0x0000563985f7d0b8 in vhost_user_blk_connect (dev=0x563989cf7990)
at hw/block/vhost-user-blk.c:315
#5 0x0000563985f7d3f6 in vhost_user_blk_event (opaque=0x563989cf7990,
event=CHR_EVENT_OPENED)
at hw/block/vhost-user-blk.c:379
Update the vhost-user-blk device with the internal started_vu field which
will be used for initialization (vhost_user_blk_start) and clean up
(vhost_user_blk_stop). This additional flag in the VhostUserBlk structure
will be used to track whether the device really needs to be stopped and
cleaned up on a vhost-user level.
The disconnect event will set the overall VHOST device (not vhost-user) to
the stopped state, so it can be used by the general vhost_migration_log
routine.
Such approach could be propogated to the other vhost-user devices, but
better idea is just to make the same connect/disconnect code for all the
vhost-user devices.
This migration issue was slightly discussed earlier:
- https://lists.gnu.org/archive/html/qemu-devel/2020-05/msg01509.html
- https://lists.gnu.org/archive/html/qemu-devel/2020-05/msg05241.html
Signed-off-by: Dima Stepanov <dimastep@yandex-team.ru>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <9fbfba06791a87813fcee3e2315f0b904cc6789a.1599813294.git.dimastep@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Fuzzing discovered that virtqueue_unmap_sg() is being called on modified
req->in/out_sg iovecs. This means dma_memory_map() and
dma_memory_unmap() calls do not have matching memory addresses.
Fuzzing discovered that non-RAM addresses trigger a bug:
void address_space_unmap(AddressSpace *as, void *buffer, hwaddr len,
bool is_write, hwaddr access_len)
{
if (buffer != bounce.buffer) {
^^^^^^^^^^^^^^^^^^^^^^^
A modified iov->iov_base is no longer recognized as a bounce buffer and
the wrong branch is taken.
There are more potential bugs: dirty memory is not tracked correctly and
MemoryRegion refcounts can be leaked.
Use the new iov_discard_undo() API to restore elem->in/out_sg before
virtqueue_push() is called.
Fixes: 827805a249 ("virtio-blk: Convert VirtIOBlockReq.out to structrue")
Reported-by: Alexander Bulekov <alxndr@bu.edu>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
Buglink: https://bugs.launchpad.net/qemu/+bug/1890360
Message-Id: <20200917094455.822379-3-stefanha@redhat.com>
Some trace points are attributed to the wrong source file. Happens
when we neglect to update trace-events for code motion, or add events
in the wrong place, or misspell the file name.
Clean up with help of scripts/cleanup-trace-events.pl. Funnies
requiring manual post-processing:
* accel/tcg/cputlb.c trace points are in trace-events.
* block.c and blockdev.c trace points are in block/trace-events.
* hw/block/nvme.c uses the preprocessor to hide its trace point use
from cleanup-trace-events.pl.
* hw/tpm/tpm_spapr.c uses pseudo trace point tpm_spapr_show_buffer to
guard debug code.
* include/hw/xen/xen_common.h trace points are in hw/xen/trace-events.
* linux-user/trace-events abbreviates a tedious list of filenames to
*/signal.c.
* net/colo-compare and net/filter-rewriter.c use pseudo trace points
colo_compare_miscompare and colo_filter_rewriter_debug to guard
debug code.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200806141334.3646302-5-armbru@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Some typedefs and macros are defined after the type check macros.
This makes it difficult to automatically replace their
definitions with OBJECT_DECLARE_TYPE.
Patch generated using:
$ ./scripts/codeconverter/converter.py -i \
--pattern=QOMStructTypedefSplit $(git grep -l '' -- '*.[ch]')
which will split "typdef struct { ... } TypedefName"
declarations.
Followed by:
$ ./scripts/codeconverter/converter.py -i --pattern=MoveSymbols \
$(git grep -l '' -- '*.[ch]')
which will:
- move the typedefs and #defines above the type check macros
- add missing #include "qom/object.h" lines if necessary
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-9-ehabkost@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Message-Id: <20200831210740.126168-10-ehabkost@redhat.com>
Message-Id: <20200831210740.126168-11-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
-----BEGIN PGP SIGNATURE-----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=ZQHA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20200901' into staging
Various fixes of Aspeed machines :
* New Supermicro X11 BMC machine (Erik)
* Fixed valid access size on AST2400 SCU
* Improved robustness of the ftgmac100 model.
* New flash models in m25p80 (Igor)
* Fixed reset sequence of SDHCI/eMMC controllers
* Improved support of the AST2600 SDMC (Joel)
* Couple of SMC cleanups
# gpg: Signature made Tue 01 Sep 2020 13:39:20 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20200901:
hw: add a number of SPI-flash's of m25p80 family
arm: aspeed: add strap define `25HZ` of AST2500
aspeed/smc: Open AHB window of the second chip of the AST2600 FMC controller
aspeed/sdmc: Simplify calculation of RAM bits
aspeed/sdmc: Allow writes to unprotected registers
aspeed/sdmc: Perform memory training
ftgmac100: Improve software reset
ftgmac100: Fix integer overflow in ftgmac100_do_tx()
ftgmac100: Check for invalid len and address before doing a DMA transfer
ftgmac100: Change interrupt status when a DMA error occurs
ftgmac100: Fix interrupt status "Packet moved to RX FIFO"
ftgmac100: Fix interrupt status "Packet transmitted on ethernet"
ftgmac100: Fix registers that can be read
aspeed/sdhci: Fix reset sequence
aspeed/smc: Fix max_slaves of the legacy SMC device
aspeed/smc: Fix MemoryRegionOps definition
hw/arm/aspeed: Add board model for Supermicro X11 BMC
aspeed/scu: Fix valid access size on AST2400
m25p80: Add support for n25q512ax3
m25p80: Return the JEDEC ID twice for mx25l25635e
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since nvme_map_prp always operate on the request-scoped qsg/iovs, just
pass a single pointer to the NvmeRequest instead of two for each of the
qsg and iov.
Suggested-by: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Since clean up of the request qsg/iov is now always done post-use, there
is no need to use a stack-allocated qsg/iov in nvme_dma_prp.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Always destroy the request qsg/iov at the end of request use.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Instead of passing around the NvmeNamespace and the NvmeCmd, add them as
members in the NvmeRequest structure.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
The NVM Express specification generally uses 'zeroes' and not 'zeros',
so let us align with it.
Cc: Fam Zheng <fam@euphon.net>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Add 'mdts' device parameter to control the Maximum Data Transfer Size of
the controller and check that it is respected.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Hoist bounds checking into its own function and check for wrap-around.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Before this patch the device already supported PRP lists in the CMB, but
it did not check for the validity of it nor announced the support in the
Identify Controller data structure LISTS field.
If some of the PRPs in a PRP list are in the CMB, then ALL entries must
be there. This patch makes sure that requirement is verified as well as
properly announcing support for PRP lists in the CMB.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Introduce the nvme_map helper to remove some noise in the main nvme_rw
function.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Refactor the nvme_dma_{read,write}_prp functions into a common function
taking a DMADirection parameter.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Make sure the request iov is destroyed before reuse; fixing a memory
leak.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Remove the has_sg member from NvmeRequest since it's redundant.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
The QSG isn't always initialized, so accounting could be wrong. Issue a
call to blk_acct_start instead with the size taken from the QSG or IOV
depending on the kind of I/O.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Add nvme_map_addr, nvme_map_addr_cmb and nvme_addr_to_cmb helpers and
use them in nvme_map_prp.
This fixes a bug where in the case of a CMB transfer, the device would
map to the buffer with a wrong length.
Fixes: b2b2b67a00 ("nvme: Add support for Read Data and Write Data in CMBs.")
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Andrzej Jakowski <andrzej.jakowski@linux.intel.com>
This is preparatory to subsequent patches that change how QSGs/IOVs are
handled. It is important that the qsg and iov members of the NvmeRequest
are initially zeroed.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
The SUBNQN field is mandatory in NVM Express 1.3.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-18-its@irrelevant.dk>
Support returning Command Sequence Error if Set Features on Number of
Queues is called after queues have been created.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-17-its@irrelevant.dk>
Reject the nsid broadcast value (0xffffffff) and 0xfffffffe in the
Active Namespace ID list.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-16-its@irrelevant.dk>
Since we are not providing the NGUID or EUI64 fields, we must support
the Namespace UUID. We do not have any way of storing a persistent
unique identifier, so conjure up a UUID that is just the namespace id.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-15-its@irrelevant.dk>
0xffff is not an allowed value for NCQR and NSQR in Set Features on
Number of Queues.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-14-its@irrelevant.dk>
Since the device does not have any persistent state storage, no
features are "saveable" and setting the Save (SV) field in any Set
Features command will result in a Feature Identifier Not Saveable status
code.
Similarly, if the Select (SEL) field is set to request saved values, the
devices will (as it should) return the default values instead.
Since this also introduces "Supported Capabilities", the nsid field is
now also checked for validity wrt. the feature being get/set'ed.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-13-its@irrelevant.dk>
If the write cache is disabled with a Set Features command, flush it if
currently enabled.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-11-its@irrelevant.dk>
The NvmeFeatureVal does not belong with the spec-related data structures
in include/block/nvme.h that is shared between the block-level nvme
driver and the emulated nvme device.
Move it into the nvme device specific header file as it is the only
user of the structure. Also, remove the unused members.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-10-its@irrelevant.dk>
Add support for the Asynchronous Event Request command. Required for
compliance with NVMe revision 1.3d. See NVM Express 1.3d, Section 5.2
("Asynchronous Event Request command").
Mostly imported from Keith's qemu-nvme tree. Modified with a max number
of queued events (controllable with the aer_max_queued device
parameter). The spec states that the controller *should* retain
events, so we do best effort here.
Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-9-its@irrelevant.dk>
Add support for the Get Log Page command and basic implementations of
the mandatory Error Information, SMART / Health Information and Firmware
Slot Information log pages.
In violation of the specification, the SMART / Health Information log
page does not persist information over the lifetime of the controller
because the device has no place to store such persistent state.
Note that the LPA field in the Identify Controller data structure
intentionally has bit 0 cleared because there is no namespace specific
information in the SMART / Health information log page.
Required for compliance with NVMe revision 1.3d. See NVM Express 1.3d,
Section 5.14 ("Get Log Page command").
Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-8-its@irrelevant.dk>
Mark firmware slot 1 as read-only and only support that slot.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-7-its@irrelevant.dk>
It might seem weird to implement this feature for an emulated device,
but it is mandatory to support and the feature is useful for testing
asynchronous event request support, which will be added in a later
patch.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-6-its@irrelevant.dk>
Required for compliance with NVMe revision 1.3d. See NVM Express 1.3d,
Section 5.1 ("Abort command").
The Abort command is a best effort command; for now, the device always
fails to abort the given command.
Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-5-its@irrelevant.dk>
Add various additional tracing and streamline nvme_identify_ns and
nvme_identify_nslist (they do not need to repeat the command, it is
already in the trace name).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-4-its@irrelevant.dk>
Fix a missing cpu_to conversion by moving conversion to just before
returning instead.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Suggested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200706061303.246057-3-its@irrelevant.dk>
Add missing fields in the Identify Controller and Identify Namespace
data structures to bring them in line with NVMe v1.3.
This also adds data structures and defines for SGL support which
requires a couple of trivial changes to the nvme block driver as well.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Fam Zheng <fam@euphon.net>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Message-Id: <20200706061303.246057-2-its@irrelevant.dk>
Simplify the NVMe emulated device by aligning the I/O BAR to 4 KiB.
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200630110429.19972-5-philmd@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
At some point the URL changed, update it to avoid other
developers to search for it.
Reviewed-by: Dmitry Fomichev <dmitry.fomichev@wdc.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200630110429.19972-2-philmd@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Support a following SPI flashes:
* mx66l51235f
* mt25ql512ab
Signed-off-by: Igor Kononenko <i.kononenko@yadro.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20200811203724.20699-1-i.kononenko@yadro.com>
Message-Id: <20200819100956.2216690-22-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The mx25l25635e returns the JEDEC ID twice when issuing a RDID command :
[ 2.512027] aspeed-smc 1e630000.spi: reading JEDEC ID C2:20:19:C2:20:19
This can break some firmware testing for this condition on the
supermicrox11-bmc machine.
Reported-by: Erik Smit <erik.lucas.smit@gmail.com>
Message-Id: <20200819100956.2216690-2-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Remove superfluous breaks, as there is a "return" before them.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1594631126-36631-1-git-send-email-wang.yi59@zte.com.cn>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Currently we have a SWIM typedef and a SWIM type checking macro,
but OBJECT_DECLARE* would transform the SWIM macro into a
function, and the function name would conflict with the SWIM
typedef name.
Rename the struct and typedef to "Swim". This will make future
conversion to OBJECT_DECLARE* easier.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Tested-By: Roman Bolshakov <r.bolshakov@yadro.com>
Message-Id: <20200825192110.3528606-50-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Automatically size the number of request virtqueues to match the number
of vCPUs. This ensures that completion interrupts are handled on the
same vCPU that submitted the request. No IPI is necessary to complete
an I/O request and performance is improved. The maximum number of MSI-X
vectors and virtqueues limit are respected.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Message-Id: <20200818143348.310613-8-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Automatically size the number of virtio-blk-pci request virtqueues to
match the number of vCPUs. Other transports continue to default to 1
request virtqueue.
A 1:1 virtqueue:vCPU mapping ensures that completion interrupts are
handled on the same vCPU that submitted the request. No IPI is
necessary to complete an I/O request and performance is improved. The
maximum number of MSI-X vectors and virtqueues limit are respected.
Performance improves from 78k to 104k IOPS on a 32 vCPU guest with 101
virtio-blk-pci devices (ioengine=libaio, iodepth=1, bs=4k, rw=randread
with NVMe storage).
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Message-Id: <20200818143348.310613-7-stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Meson doesn't enjoy the same flexibility we have with Make in choosing
the include path. In particular the tracing headers are using
$(build_root)/$(<D).
In order to keep the include directives unchanged,
the simplest solution is to generate headers with patterns like
"trace/trace-audio.h" and place forwarding headers in the source tree
such that for example "audio/trace.h" includes "trace/trace-audio.h".
This patch is too ugly to be applied to the Makefiles now. It's only
a way to separate the changes to the tracing header files from the
Meson rewrite of the tracing logic.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
object_get_canonical_path_component() returns a malloced copy of a
property name on success, null on failure.
19 of its 25 callers immediately free the returned copy.
Change object_get_canonical_path_component() to return the property
name directly. Since modifying the name would be wrong, adjust the
return type to const char *.
Drop the free from the 19 callers become simpler, add the g_strdup()
to the other six.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200714160202.3121879-4-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Li Qiang <liq3ea@gmail.com>
If we want to check error after errp-function call, we need to
introduce local_err and then propagate it to errp. Instead, use
the ERRP_GUARD() macro, benefits are:
1. No need of explicit error_propagate call
2. No need of explicit local_err variable: use errp directly
3. ERRP_GUARD() leaves errp as is if it's not NULL or
&error_fatal, this means that we don't break error_abort
(we'll abort on error_set, not on error_propagate)
If we want to add some info to errp (by error_prepend() or
error_append_hint()), we must use the ERRP_GUARD() macro.
Otherwise, this info will not be added when errp == &error_fatal
(the program will exit prior to the error_append_hint() or
error_prepend() call). No such cases are being fixed here.
This commit is generated by command
sed -n '/^X86 Xen CPUs$/,/^$/{s/^F: //p}' MAINTAINERS | \
xargs git ls-files | grep '\.[hc]$' | \
xargs spatch \
--sp-file scripts/coccinelle/errp-guard.cocci \
--macro-file scripts/cocci-macro-file.h \
--in-place --no-show-diff --max-width 80
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reported-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200707165037.1026246-9-armbru@redhat.com>
[ERRP_AUTO_PROPAGATE() renamed to ERRP_GUARD(), and
auto-propagated-errp.cocci to errp-guard.cocci. Commit message
tweaked again.]
If we want to check error after errp-function call, we need to
introduce local_err and then propagate it to errp. Instead, use
the ERRP_GUARD() macro, benefits are:
1. No need of explicit error_propagate call
2. No need of explicit local_err variable: use errp directly
3. ERRP_GUARD() leaves errp as is if it's not NULL or
&error_fatal, this means that we don't break error_abort
(we'll abort on error_set, not on error_propagate)
If we want to add some info to errp (by error_prepend() or
error_append_hint()), we must use the ERRP_GUARD() macro.
Otherwise, this info will not be added when errp == &error_fatal
(the program will exit prior to the error_append_hint() or
error_prepend() call). No such cases are being fixed here.
This commit is generated by command
sed -n '/^Parallel NOR Flash devices$/,/^$/{s/^F: //p}' \
MAINTAINERS | \
xargs git ls-files | grep '\.[hc]$' | \
xargs spatch \
--sp-file scripts/coccinelle/errp-guard.cocci \
--macro-file scripts/cocci-macro-file.h \
--in-place --no-show-diff --max-width 80
Reported-by: Kevin Wolf <kwolf@redhat.com>
Reported-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
[Commit message tweaked]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200707165037.1026246-5-armbru@redhat.com>
[ERRP_AUTO_PROPAGATE() renamed to ERRP_GUARD(), and
auto-propagated-errp.cocci to errp-guard.cocci. Commit message
tweaked again.]
Convert
visit_type_FOO(v, ..., &ptr, &err);
...
if (err) {
...
}
to
visit_type_FOO(v, ..., &ptr, errp);
...
if (!ptr) {
...
}
for functions that set @ptr to non-null / null on success / error.
Eliminate error_propagate() that are now unnecessary. Delete @err
that are now unused.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-40-armbru@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. The previous two commits did that for sufficiently simple
cases with Coccinelle. Do it for several more manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-37-armbru@redhat.com>
When all we do with an Error we receive into a local variable is
propagating to somewhere else, we can just as well receive it there
right away. Convert
if (!foo(..., &err)) {
...
error_propagate(errp, err);
...
return ...
}
to
if (!foo(..., errp)) {
...
...
return ...
}
where nothing else needs @err. Coccinelle script:
@rule1 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
binary operator op;
constant c1, c2;
symbol false;
@@
if (
(
- fun(args, &err, args2)
+ fun(args, errp, args2)
|
- !fun(args, &err, args2)
+ !fun(args, errp, args2)
|
- fun(args, &err, args2) op c1
+ fun(args, errp, args2) op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
)
}
@rule2 forall@
identifier fun, err, errp, lbl;
expression list args, args2;
expression var;
binary operator op;
constant c1, c2;
symbol false;
@@
- var = fun(args, &err, args2);
+ var = fun(args, errp, args2);
... when != err
if (
(
var
|
!var
|
var op c1
)
)
{
... when != err
when != lbl:
when strict
- error_propagate(errp, err);
... when != err
(
return;
|
return c2;
|
return false;
|
return var;
)
}
@depends on rule1 || rule2@
identifier err;
@@
- Error *err = NULL;
... when != err
Not exactly elegant, I'm afraid.
The "when != lbl:" is necessary to avoid transforming
if (fun(args, &err)) {
goto out
}
...
out:
error_propagate(errp, err);
even though other paths to label out still need the error_propagate().
For an actual example, see sclp_realize().
Without the "when strict", Coccinelle transforms vfio_msix_setup(),
incorrectly. I don't know what exactly "when strict" does, only that
it helps here.
The match of return is narrower than what I want, but I can't figure
out how to express "return where the operand doesn't use @err". For
an example where it's too narrow, see vfio_intx_enable().
Silently fails to convert hw/arm/armsse.c, because Coccinelle gets
confused by ARMSSE being used both as typedef and function-like macro
there. Converted manually.
Line breaks tidied up manually. One nested declaration of @local_err
deleted manually. Preexisting unwanted blank line dropped in
hw/riscv/sifive_e.c.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20200707160613.848843-35-armbru@redhat.com>
The previous commit enables conversion of
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., errp)) {
...
}
for QOM functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun = {
object_apply_global_props, object_initialize_child_with_props,
object_initialize_child_with_propsv, object_property_get,
object_property_get_bool, object_property_parse, object_property_set,
object_property_set_bool, object_property_set_int,
object_property_set_link, object_property_set_qobject,
object_property_set_str, object_property_set_uint, object_set_props,
object_set_propv, user_creatable_add_dict,
user_creatable_complete, user_creatable_del
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-29-armbru@redhat.com>
The object_property_set_FOO() setters take property name and value in
an unusual order:
void object_property_set_FOO(Object *obj, FOO_TYPE value,
const char *name, Error **errp)
Having to pass value before name feels grating. Swap them.
Same for object_property_set(), object_property_get(), and
object_property_parse().
Convert callers with this Coccinelle script:
@@
identifier fun = {
object_property_get, object_property_parse, object_property_set_str,
object_property_set_link, object_property_set_bool,
object_property_set_int, object_property_set_uint, object_property_set,
object_property_set_qobject
};
expression obj, v, name, errp;
@@
- fun(obj, v, name, errp)
+ fun(obj, name, v, errp)
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Convert that one manually.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Convert manually.
Fails to convert hw/rx/rx-gdbsim.c, because Coccinelle gets confused
by RXCPU being used both as typedef and function-like macro there.
Convert manually. The other files using RXCPU that way don't need
conversion.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-27-armbru@redhat.com>
[Straightforwad conflict with commit 2336172d9b "audio: set default
value for pcspk.iobase property" resolved]
The previous commit enables conversion of
visit_foo(..., &err);
if (err) {
...
}
to
if (!visit_foo(..., errp)) {
...
}
for visitor functions that now return true / false on success / error.
Coccinelle script:
@@
identifier fun =~ "check_list|input_type_enum|lv_start_struct|lv_type_bool|lv_type_int64|lv_type_str|lv_type_uint64|output_type_enum|parse_type_bool|parse_type_int64|parse_type_null|parse_type_number|parse_type_size|parse_type_str|parse_type_uint64|print_type_bool|print_type_int64|print_type_null|print_type_number|print_type_size|print_type_str|print_type_uint64|qapi_clone_start_alternate|qapi_clone_start_list|qapi_clone_start_struct|qapi_clone_type_bool|qapi_clone_type_int64|qapi_clone_type_null|qapi_clone_type_number|qapi_clone_type_str|qapi_clone_type_uint64|qapi_dealloc_start_list|qapi_dealloc_start_struct|qapi_dealloc_type_anything|qapi_dealloc_type_bool|qapi_dealloc_type_int64|qapi_dealloc_type_null|qapi_dealloc_type_number|qapi_dealloc_type_str|qapi_dealloc_type_uint64|qobject_input_check_list|qobject_input_check_struct|qobject_input_start_alternate|qobject_input_start_list|qobject_input_start_struct|qobject_input_type_any|qobject_input_type_bool|qobject_input_type_bool_keyval|qobject_input_type_int64|qobject_input_type_int64_keyval|qobject_input_type_null|qobject_input_type_number|qobject_input_type_number_keyval|qobject_input_type_size_keyval|qobject_input_type_str|qobject_input_type_str_keyval|qobject_input_type_uint64|qobject_input_type_uint64_keyval|qobject_output_start_list|qobject_output_start_struct|qobject_output_type_any|qobject_output_type_bool|qobject_output_type_int64|qobject_output_type_null|qobject_output_type_number|qobject_output_type_str|qobject_output_type_uint64|start_list|visit_check_list|visit_check_struct|visit_start_alternate|visit_start_list|visit_start_struct|visit_type_.*";
expression list args;
typedef Error;
Error *err;
@@
- fun(args, &err);
- if (err)
+ if (!fun(args, &err))
{
...
}
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20200707160613.848843-19-armbru@redhat.com>
Convert
foo(..., &err);
if (err) {
...
}
to
if (!foo(..., &err)) {
...
}
for qdev_realize(), qdev_realize_and_unref(), qbus_realize() and their
wrappers isa_realize_and_unref(), pci_realize_and_unref(),
sysbus_realize(), sysbus_realize_and_unref(), usb_realize_and_unref().
Coccinelle script:
@@
identifier fun = {
isa_realize_and_unref, pci_realize_and_unref, qbus_realize,
qdev_realize, qdev_realize_and_unref, sysbus_realize,
sysbus_realize_and_unref, usb_realize_and_unref
};
expression list args, args2;
typedef Error;
Error *err;
@@
- fun(args, &err, args2);
- if (err)
+ if (!fun(args, &err, args2))
{
...
}
Chokes on hw/arm/musicpal.c's lcd_refresh() with the unhelpful error
message "no position information". Nothing to convert there; skipped.
Fails to convert hw/arm/armsse.c, because Coccinelle gets confused by
ARMSSE being used both as typedef and function-like macro there.
Converted manually.
A few line breaks tidied up manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20200707160613.848843-5-armbru@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20200619091905.21676-6-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
acpi aml generator needs this, but it is in floppy code now
so we can make the function static.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20200619091905.21676-5-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
DSDT change: isa device order changes in case MI1 (ipmi) is present.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20200619091905.21676-4-kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
qdev_prop_set_drive() can fail. None of the other qdev_prop_set_FOO()
can; they abort on error.
To clean up this inconsistency, rename qdev_prop_set_drive() to
qdev_prop_set_drive_err(), and create a qdev_prop_set_drive() that
aborts on error.
Coccinelle script to update callers:
@ depends on !(file in "hw/core/qdev-properties-system.c")@
expression dev, name, value;
symbol error_abort;
@@
- qdev_prop_set_drive(dev, name, value, &error_abort);
+ qdev_prop_set_drive(dev, name, value);
@@
expression dev, name, value, errp;
@@
- qdev_prop_set_drive(dev, name, value, errp);
+ qdev_prop_set_drive_err(dev, name, value, errp);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-14-armbru@redhat.com>
Deprecate
-global isa-fdc.driveA=...
-global isa-fdc.driveB=...
in favour of
-device floppy,unit=0,drive=...
-device floppy,unit=1,drive=...
Same for the other floppy controller devices.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: John Snow <jsnow@redhat.com>
Message-Id: <20200622094227.1271650-7-armbru@redhat.com>
Helper function fdctrl_init_isa() is less than helpful: one of three
places creating "isa-fdc" devices use it. Open-code it there, and
drop the function.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200622094227.1271650-6-armbru@redhat.com>
The floppy controller devices desugar their drive properties into
floppy devices (since commit a92bd191a4 "fdc: Move qdev properties to
FloppyDrive", v2.8.0). This involves some bad magic in
fdctrl_connect_drives(), and exists for backward compatibility.
The functions for boards to create floppy controller devices
fdctrl_init_isa(), fdctrl_init_sysbus(), and sun4m_fdctrl_init()
desugar -drive if=floppy to these floppy controller drive properties.
If you use both -drive if=floppy (or its -fda / -fdb sugar) and
-global isa-fdc for the same floppy device, -global silently loses the
conflict, and both backends involved end up with the floppy device
frontend attached, as demonstrated by iotest 172 (see commit before
previous). This is wrong.
Desugar -drive if=floppy straight to floppy devices instead, with
helper fdctrl_init_drives(). The conflict now gets rejected cleanly:
first, fdctrl_connect_drives() creates the floppy for the controller's
property, then fdctrl_init_drives() attempts to create the floppy for
-drive if=floppy, but fails because the unit is already in use.
Output of iotest 172 changes in three ways:
1. The clash gets rejected.
2. In one test case, "info qtree" has the floppy devices swapped, and
"info block" has their QOM paths swapped. This is because the
floppy device for -fda now gets created after the one for -global
isa-fdc.driveB.
3. The error message for -global floppy.drive=floppy0 changes. Before
the patch, we set isa-fdc.driveA to -fda's block backend, then
create the floppy device for it, then move the backend from
isa-fdc.driveA to floppy.drive. Floppy creation fails when
applying -global floppy.drive=floppy0, because floppy0 is still
attached to isa-fdc. After the patch, we create the floppy for
-fda, then set its drive property to floppy0. Now floppy creation
succeeds, but setting the drive property fails, because -global
already set it. Yes, this is exasperatingly complicated.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200622094227.1271650-5-armbru@redhat.com>
Convert all size-related properties in BlockConf to 32bit. This will
accommodate bigger block sizes (in a followup patch). This also allows
to make them all accept size suffixes, either via DEFINE_PROP_BLOCKSIZE
or via DEFINE_PROP_SIZE32.
Also, since min_io_size is exposed to the guest by scsi and virtio-blk
devices as an uint16_t in units of logical blocks, introduce an
additional check in blkconf_blocksizes to prevent its silent truncation.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Message-Id: <20200528225516.1676602-7-rvkagan@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Several block device properties related to blocksize configuration must
be in certain relationship WRT each other: physical block must be no
smaller than logical block; min_io_size, opt_io_size, and
discard_granularity must be a multiple of a logical block.
To ensure these requirements are met, add corresponding consistency
checks to blkconf_blocksizes, adjusting its signature to communicate
possible error to the caller. Also remove the now redundant consistency
checks from the specific devices.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Message-Id: <20200528225516.1676602-3-rvkagan@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The width of opt_io_size in virtio_blk_config is 32bit. However, it's
written with virtio_stw_p; this may result in value truncation, and on
big-endian systems with legacy virtio in completely bogus readings in
the guest.
Use the appropriate accessor to store it.
Signed-off-by: Roman Kagan <rvkagan@yandex-team.ru>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200528225516.1676602-2-rvkagan@yandex-team.ru>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pass an Error to msix_init_exclusive_bar() and check it.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20200609190333.59390-23-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Decouple the requested maximum number of ioqpairs (param max_ioqpairs)
from the number of MSI-X interrupt vectors by introducing a new
msix_qsize parameter and initialize MSI-X with that. This allows
emulating a device that has fewer vectors than I/O queue pairs and also
allows more than 2048 queue pairs. To keep the device behaving as
previously, use a msix_qsize default of 65 (default max_ioqpairs + 1).
This decoupling was actually suggested by Maxim some time ago in a
slightly different context, so adding a Suggested-by.
Suggested-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Message-Id: <20200609190333.59390-22-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
msix_vector_use() returns -EINVAL on error. Assert it won't.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200609190333.59390-21-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-20-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200609190333.59390-19-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200609190333.59390-18-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-17-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-16-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-15-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Introduce some small helpers to make the next patches easier on the eye.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-14-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-13-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-12-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-11-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-10-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The num_queues device paramater has a slightly confusing meaning because
it accounts for the admin queue pair which is not really optional.
Secondly, it is really a maximum value of queues allowed.
Add a new max_ioqpairs parameter that only accounts for I/O queue pairs,
but keep num_queues for compatibility.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-9-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
First, since the device only supports MSI-X or pin-based interrupt, if
MSI-X is not enabled, it should not accept interrupt vectors different
from 0 when creating completion queues.
Secondly, the irq_status NvmeCtrl member is meant to be compared to the
INTMS register, so it should only be 32 bits wide. And it is really only
useful when used with multi-message MSI.
Third, since we do not force a 1-to-1 correspondence between cqid and
interrupt vector, the irq_status register should not have bits set
according to cqid, but according to the associated interrupt vector.
Fix these issues, but keep irq_status available so we can easily support
multi-message MSI down the line.
Fixes: 5e9aa92eb1 ("hw/block: Fix pin-based interrupt behaviour of NVMe")
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-8-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Pull the controller memory buffer check to its own function. The check
will be used on its own in later patches.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-7-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-6-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move device configuration parameters to separate struct to make it
explicit what is configurable and what is set internally.
Signed-off-by: Klaus Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Message-Id: <20200609190333.59390-5-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These break statements was left over when commit 3036a626e9 ("nvme:
add Get/Set Feature Timestamp support") was merged.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-4-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Change the prefix of all nvme device related trace events to 'pci_nvme'
to not clash with trace events from the nvme block driver.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-3-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The size of the BAR is 0x1000 (main registers) + 8 bytes for each
queue. Currently, the size of the BAR is calculated like so:
n->reg_size = pow2ceil(0x1004 + 2 * (n->num_queues + 1) * 4);
Since the 'num_queues' parameter already accounts for the admin queue,
this should in any case not need to be incremented by one. Also, the
size should be initialized to (0x1000).
n->reg_size = pow2ceil(0x1000 + 2 * n->num_queues * 4);
This, with the default value of num_queues (64), we will set aside room
for 1 admin queue and 63 I/O queues (4 bytes per doorbell, 2 doorbells
per queue).
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Message-Id: <20200609190333.59390-2-its@irrelevant.dk>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
On restart, we were scheduling a BH to process queued requests, which
would run before starting up the data plane, leading to those requests
being assigned and started on coroutines on the main context.
This could cause requests to be wrongly processed in parallel from
different threads (the main thread and the iothread managing the data
plane), potentially leading to multiple issues.
For example, stopping and resuming a VM multiple times while the guest
is generating I/O on a virtio_blk device can trigger a crash with a
stack tracing looking like this one:
<------>
Thread 2 (Thread 0x7ff736765700 (LWP 1062503)):
#0 0x00005567a13b99d6 in iov_memset
(iov=0x6563617073206f4e, iov_cnt=1717922848, offset=516096, fillc=0, bytes=7018105756081554803)
at util/iov.c:69
#1 0x00005567a13bab73 in qemu_iovec_memset
(qiov=0x7ff73ec99748, offset=516096, fillc=0, bytes=7018105756081554803) at util/iov.c:530
#2 0x00005567a12f411c in qemu_laio_process_completion (laiocb=0x7ff6512ee6c0) at block/linux-aio.c:86
#3 0x00005567a12f42ff in qemu_laio_process_completions (s=0x7ff7182e8420) at block/linux-aio.c:217
#4 0x00005567a12f480d in ioq_submit (s=0x7ff7182e8420) at block/linux-aio.c:323
#5 0x00005567a12f43d9 in qemu_laio_process_completions_and_submit (s=0x7ff7182e8420)
at block/linux-aio.c:236
#6 0x00005567a12f44c2 in qemu_laio_poll_cb (opaque=0x7ff7182e8430) at block/linux-aio.c:267
#7 0x00005567a13aed83 in run_poll_handlers_once (ctx=0x5567a2b58c70, timeout=0x7ff7367645f8)
at util/aio-posix.c:520
#8 0x00005567a13aee9f in run_poll_handlers (ctx=0x5567a2b58c70, max_ns=16000, timeout=0x7ff7367645f8)
at util/aio-posix.c:562
#9 0x00005567a13aefde in try_poll_mode (ctx=0x5567a2b58c70, timeout=0x7ff7367645f8)
at util/aio-posix.c:597
#10 0x00005567a13af115 in aio_poll (ctx=0x5567a2b58c70, blocking=true) at util/aio-posix.c:639
#11 0x00005567a109acca in iothread_run (opaque=0x5567a2b29760) at iothread.c:75
#12 0x00005567a13b2790 in qemu_thread_start (args=0x5567a2b694c0) at util/qemu-thread-posix.c:519
#13 0x00007ff73eedf2de in start_thread () at /lib64/libpthread.so.0
#14 0x00007ff73ec10e83 in clone () at /lib64/libc.so.6
Thread 1 (Thread 0x7ff743986f00 (LWP 1062500)):
#0 0x00005567a13b99d6 in iov_memset
(iov=0x6563617073206f4e, iov_cnt=1717922848, offset=516096, fillc=0, bytes=7018105756081554803)
at util/iov.c:69
#1 0x00005567a13bab73 in qemu_iovec_memset
(qiov=0x7ff73ec99748, offset=516096, fillc=0, bytes=7018105756081554803) at util/iov.c:530
#2 0x00005567a12f411c in qemu_laio_process_completion (laiocb=0x7ff6512ee6c0) at block/linux-aio.c:86
#3 0x00005567a12f42ff in qemu_laio_process_completions (s=0x7ff7182e8420) at block/linux-aio.c:217
#4 0x00005567a12f480d in ioq_submit (s=0x7ff7182e8420) at block/linux-aio.c:323
#5 0x00005567a12f4a2f in laio_do_submit (fd=19, laiocb=0x7ff5f4ff9ae0, offset=472363008, type=2)
at block/linux-aio.c:375
#6 0x00005567a12f4af2 in laio_co_submit
(bs=0x5567a2b8c460, s=0x7ff7182e8420, fd=19, offset=472363008, qiov=0x7ff5f4ff9ca0, type=2)
at block/linux-aio.c:394
#7 0x00005567a12f1803 in raw_co_prw
(bs=0x5567a2b8c460, offset=472363008, bytes=20480, qiov=0x7ff5f4ff9ca0, type=2)
at block/file-posix.c:1892
#8 0x00005567a12f1941 in raw_co_pwritev
(bs=0x5567a2b8c460, offset=472363008, bytes=20480, qiov=0x7ff5f4ff9ca0, flags=0)
at block/file-posix.c:1925
#9 0x00005567a12fe3e1 in bdrv_driver_pwritev
(bs=0x5567a2b8c460, offset=472363008, bytes=20480, qiov=0x7ff5f4ff9ca0, qiov_offset=0, flags=0)
at block/io.c:1183
#10 0x00005567a1300340 in bdrv_aligned_pwritev
(child=0x5567a2b5b070, req=0x7ff5f4ff9db0, offset=472363008, bytes=20480, align=512, qiov=0x7ff72c0425b8, qiov_offset=0, flags=0) at block/io.c:1980
#11 0x00005567a1300b29 in bdrv_co_pwritev_part
(child=0x5567a2b5b070, offset=472363008, bytes=20480, qiov=0x7ff72c0425b8, qiov_offset=0, flags=0)
at block/io.c:2137
#12 0x00005567a12baba1 in qcow2_co_pwritev_task
(bs=0x5567a2b92740, file_cluster_offset=472317952, offset=487305216, bytes=20480, qiov=0x7ff72c0425b8, qiov_offset=0, l2meta=0x0) at block/qcow2.c:2444
#13 0x00005567a12bacdb in qcow2_co_pwritev_task_entry (task=0x5567a2b48540) at block/qcow2.c:2475
#14 0x00005567a13167d8 in aio_task_co (opaque=0x5567a2b48540) at block/aio_task.c:45
#15 0x00005567a13cf00c in coroutine_trampoline (i0=738245600, i1=32759) at util/coroutine-ucontext.c:115
#16 0x00007ff73eb622e0 in __start_context () at /lib64/libc.so.6
#17 0x00007ff6626f1350 in ()
#18 0x0000000000000000 in ()
<------>
This is also known to cause crashes with this message (assertion
failed):
aio_co_schedule: Co-routine was already scheduled in 'aio_co_schedule'
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1812765
Signed-off-by: Sergio Lopez <slp@redhat.com>
Message-Id: <20200603093240.40489-3-slp@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move the code that processes queued requests from
virtio_blk_dma_restart_bh() to its own, non-static, function. This
will allow us to call it from the virtio_blk_data_plane_start() in a
future patch.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Message-Id: <20200603093240.40489-2-slp@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
All remaining conversions to qdev_realize() are for bus-less devices.
Coccinelle script:
// only correct for bus-less @dev!
@@
expression errp;
expression dev;
@@
- qdev_init_nofail(dev);
+ qdev_realize(dev, NULL, &error_fatal);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
@ depends on !(file in "hw/core/qdev.c") && !(file in "hw/core/bus.c")@
expression errp;
expression dev;
symbol true;
@@
- object_property_set_bool(dev, true, "realized", errp);
+ qdev_realize(DEVICE(dev), NULL, errp);
Note that Coccinelle chokes on ARMSSE typedef vs. macro in
hw/arm/armsse.c. Worked around by temporarily renaming the macro for
the spatch run.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-57-armbru@redhat.com>
Same transformation as in the previous commit. Manual, because
convincing Coccinelle to transform these cases is not worthwhile.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-21-armbru@redhat.com>
Same transformation as in the previous commit. Manual, because
convincing Coccinelle to transform these cases is somewhere between
not worthwhile and infeasible (at least for me).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-11-armbru@redhat.com>
This is the transformation explained in the commit before previous.
Takes care of just one pattern that needs conversion. More to come in
this series.
Coccinelle script:
@ depends on !(file in "hw/arm/highbank.c")@
expression bus, type_name, dev, expr;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr;
identifier DOWN;
@@
- dev = DOWN(qdev_create(bus, type_name));
+ dev = DOWN(qdev_new(type_name));
... when != dev = expr
- qdev_init_nofail(DEVICE(dev));
+ qdev_realize_and_unref(DEVICE(dev), bus, &error_fatal);
@@
expression bus, type_name, expr;
identifier dev;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- qdev_init_nofail(dev);
+ qdev_realize_and_unref(dev, bus, &error_fatal);
@@
expression bus, type_name, dev, expr, errp;
symbol true;
@@
- dev = qdev_create(bus, type_name);
+ dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
@@
expression bus, type_name, expr, errp;
identifier dev;
symbol true;
@@
- DeviceState *dev = qdev_create(bus, type_name);
+ DeviceState *dev = qdev_new(type_name);
... when != dev = expr
- object_property_set_bool(OBJECT(dev), true, "realized", errp);
+ qdev_realize_and_unref(dev, bus, errp);
The first rule exempts hw/arm/highbank.c, because it matches along two
control flow paths there, with different @type_name. Covered by the
next commit's manual conversions.
Missing #include "qapi/error.h" added manually.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-10-armbru@redhat.com>
[Conflicts in hw/misc/empty_slot.c and hw/sparc/leon3.c resolved]
Let's start simple and put qdev_new() to use. Coccinelle script:
@ depends on !(file in "hw/core/qdev.c")@
expression type_name;
@@
- DEVICE(object_new(type_name))
+ qdev_new(type_name)
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200610053247.1583243-6-armbru@redhat.com>
We use the Object type all over the place.
Forward declare it in "qemu/typedefs.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20200504115656.6045-2-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A socket write during vhost-user communication may trigger a disconnect
event, calling vhost_user_blk_disconnect() and clearing all the
vhost_dev structures holding data that vhost-user functions expect to
remain valid to roll back initialization correctly. Delay the cleanup to
keep vhost_dev structure valid.
There are two possible states to handle:
1. RUN_STATE_PRELAUNCH: skip bh oneshot call and perform disconnect in
the caller routine.
2. RUN_STATE_RUNNING: delay by using bh
BH changes are based on the similar changes for the vhost-user-net
device:
commit e7c83a885f
"vhost-user: delay vhost_user_stop"
Signed-off-by: Dima Stepanov <dimastep@yandex-team.ru>
Message-Id: <69b73b94dcd066065595266c852810e0863a0895.1590396396.git.dimastep@yandex-team.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Li Feng <fengli@smartx.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Now than the non-target specific memory_region_msync() function
is available, use it to make this device target-agnostic.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20200508062456.23344-4-philmd@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
When updating the PFLASH file contents, we should check for a
possible failure of blk_pwrite(). Similar to commit 3a688294e.
Reported-by: Coverity (CID 1357678 CHECKED_RETURN)
Signed-off-by: Mansour Ahmadi <mansourweb@gmail.com>
Message-Id: <20200408003552.58095-1-mansourweb@gmail.com>
[PMD: Add missing "qemu/error-report.h" include and TODO comment]
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Rename the 'reset_flash' as 'mode_read_array' to make explicit we
do not reset the device, we simply set its internal state machine
in the READ_ARRAY mode. We do not reset the status register error
bits, as a device reset would do.
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190716221555.11145-5-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The command 0x00 is used by this model since its origin (commit
05ee37ebf6). In this commit the command is described with a
amusing '/* ??? */' comment, probably meaning 'FIXME'.
switch (cmd) {
case 0x00: /* ??? */
...
This comment survived 12 years because the 0x00 value is indeed
not specified by the CFI open standard (as of this commit).
The 'cmd' field is transfered during migration. To keep the
migration feature working with older QEMU version, we have to
take a lot of care with migrated field. We figured out it is
too late to remove a non-specified value from this model
(this would make migration review very complex). It is however
not too late to improve the documentation.
Add few comments to remember this is a special value related
to QEMU, and we won't find information about it on the CFI
spec.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190716221555.11145-3-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The 'CFI02' NOR flash was introduced in commit 29133e9a0f, with
timing modelled. One year later, the CFI01 model was introduced
(commit 05ee37ebf6) based on the CFI02 model. As noted in the
header, "It does not support timings". 12 years later, we never
had to model the device timings. Time to remove the unused timer,
we can still add it back if required.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
[Laszlo Ersek: Regression tested EDK2 OVMF IA32X64, ArmVirtQemu Aarch64
https://lists.gnu.org/archive/html/qemu-devel/2019-07/msg04373.html]
Message-Id: <20190716221555.11145-2-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Use the QEMU_IS_ALIGNED() macro to verify the flash block size
is properly aligned. It is quicker to process when reviewing.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20200511205246.24621-1-philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Devices may have component devices and buses.
Device realization may fail. Realization is recursive: a device's
realize() method realizes its components, and device_set_realized()
realizes its buses (which should in turn realize the devices on that
bus, except bus_set_realized() doesn't implement that, yet).
When realization of a component or bus fails, we need to roll back:
unrealize everything we realized so far. If any of these unrealizes
failed, the device would be left in an inconsistent state. Must not
happen.
device_set_realized() lets it happen: it ignores errors in the roll
back code starting at label child_realize_fail.
Since realization is recursive, unrealization must be recursive, too.
But how could a partly failed unrealize be rolled back? We'd have to
re-realize, which can fail. This design is fundamentally broken.
device_set_realized() does not roll back at all. Instead, it keeps
unrealizing, ignoring further errors.
It can screw up even for a device with no buses: if the lone
dc->unrealize() fails, it still unregisters vmstate, and calls
listeners' unrealize() callback.
bus_set_realized() does not roll back either. Instead, it stops
unrealizing.
Fortunately, no unrealize method can fail, as we'll see below.
To fix the design error, drop parameter @errp from all the unrealize
methods.
Any unrealize method that uses @errp now needs an update. This leads
us to unrealize() methods that can fail. Merely passing it to another
unrealize method cannot cause failure, though. Here are the ones that
do other things with @errp:
* virtio_serial_device_unrealize()
Fails when qbus_set_hotplug_handler() fails, but still does all the
other work. On failure, the device would stay realized with its
resources completely gone. Oops. Can't happen, because
qbus_set_hotplug_handler() can't actually fail here. Pass
&error_abort to qbus_set_hotplug_handler() instead.
* hw/ppc/spapr_drc.c's unrealize()
Fails when object_property_del() fails, but all the other work is
already done. On failure, the device would stay realized with its
vmstate registration gone. Oops. Can't happen, because
object_property_del() can't actually fail here. Pass &error_abort
to object_property_del() instead.
* spapr_phb_unrealize()
Fails and bails out when remove_drcs() fails, but other work is
already done. On failure, the device would stay realized with some
of its resources gone. Oops. remove_drcs() fails only when
chassis_from_bus()'s object_property_get_uint() fails, and it can't
here. Pass &error_abort to remove_drcs() instead.
Therefore, no unrealize method can fail before this patch.
device_set_realized()'s recursive unrealization via bus uses
object_property_set_bool(). Can't drop @errp there, so pass
&error_abort.
We similarly unrealize with object_property_set_bool() elsewhere,
always ignoring errors. Pass &error_abort instead.
Several unrealize methods no longer handle errors from other unrealize
methods: virtio_9p_device_unrealize(),
virtio_input_device_unrealize(), scsi_qdev_unrealize(), ...
Much of the deleted error handling looks wrong anyway.
One unrealize methods no longer ignore such errors:
usb_ehci_pci_exit().
Several realize methods no longer ignore errors when rolling back:
v9fs_device_realize_common(), pci_qdev_unrealize(),
spapr_phb_realize(), usb_qdev_realize(), vfio_ccw_realize(),
virtio_device_realize().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-17-armbru@redhat.com>
Several functions can't fail anymore: ich9_pm_add_properties(),
device_add_bootindex_property(), ppc_compat_add_property(),
spapr_caps_add_properties(), PropertyInfo.create(). Drop their @errp
parameter.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200505152926.18877-16-armbru@redhat.com>
when s->inflight is freed, vhost_dev_free_inflight may try to access
s->inflight->addr, it will retrigger the following issue.
==7309==ERROR: AddressSanitizer: heap-use-after-free on address 0x604001020d18 at pc 0x555555ce948a bp 0x7fffffffb170 sp 0x7fffffffb160
READ of size 8 at 0x604001020d18 thread T0
#0 0x555555ce9489 in vhost_dev_free_inflight /root/smartx/qemu-el7/qemu-test/hw/virtio/vhost.c:1473
#1 0x555555cd86eb in virtio_reset /root/smartx/qemu-el7/qemu-test/hw/virtio/virtio.c:1214
#2 0x5555560d3eff in virtio_pci_reset hw/virtio/virtio-pci.c:1859
#3 0x555555f2ac53 in device_set_realized hw/core/qdev.c:893
#4 0x5555561d572c in property_set_bool qom/object.c:1925
#5 0x5555561de8de in object_property_set_qobject qom/qom-qobject.c:27
#6 0x5555561d99f4 in object_property_set_bool qom/object.c:1188
#7 0x555555e50ae7 in qdev_device_add /root/smartx/qemu-el7/qemu-test/qdev-monitor.c:626
#8 0x555555e51213 in qmp_device_add /root/smartx/qemu-el7/qemu-test/qdev-monitor.c:806
#9 0x555555e8ff40 in hmp_device_add /root/smartx/qemu-el7/qemu-test/hmp.c:1951
#10 0x555555be889a in handle_hmp_command /root/smartx/qemu-el7/qemu-test/monitor.c:3404
#11 0x555555beac8b in monitor_command_cb /root/smartx/qemu-el7/qemu-test/monitor.c:4296
#12 0x555556433eb7 in readline_handle_byte util/readline.c:393
#13 0x555555be89ec in monitor_read /root/smartx/qemu-el7/qemu-test/monitor.c:4279
#14 0x5555563285cc in tcp_chr_read chardev/char-socket.c:470
#15 0x7ffff670b968 in g_main_context_dispatch (/lib64/libglib-2.0.so.0+0x4a968)
#16 0x55555640727c in glib_pollfds_poll util/main-loop.c:215
#17 0x55555640727c in os_host_main_loop_wait util/main-loop.c:238
#18 0x55555640727c in main_loop_wait util/main-loop.c:497
#19 0x555555b2d0bf in main_loop /root/smartx/qemu-el7/qemu-test/vl.c:2013
#20 0x555555b2d0bf in main /root/smartx/qemu-el7/qemu-test/vl.c:4776
#21 0x7fffdd2eb444 in __libc_start_main (/lib64/libc.so.6+0x22444)
#22 0x555555b3767a (/root/smartx/qemu-el7/qemu-test/x86_64-softmmu/qemu-system-x86_64+0x5e367a)
0x604001020d18 is located 8 bytes inside of 40-byte region [0x604001020d10,0x604001020d38)
freed by thread T0 here:
#0 0x7ffff6f00508 in __interceptor_free (/lib64/libasan.so.4+0xde508)
#1 0x7ffff671107d in g_free (/lib64/libglib-2.0.so.0+0x5007d)
previously allocated by thread T0 here:
#0 0x7ffff6f00a88 in __interceptor_calloc (/lib64/libasan.so.4+0xdea88)
#1 0x7ffff6710fc5 in g_malloc0 (/lib64/libglib-2.0.so.0+0x4ffc5)
SUMMARY: AddressSanitizer: heap-use-after-free /root/smartx/qemu-el7/qemu-test/hw/virtio/vhost.c:1473 in vhost_dev_free_inflight
Shadow bytes around the buggy address:
0x0c08801fc150: fa fa 00 00 00 00 04 fa fa fa fd fd fd fd fd fa
0x0c08801fc160: fa fa fd fd fd fd fd fd fa fa 00 00 00 00 04 fa
0x0c08801fc170: fa fa 00 00 00 00 00 01 fa fa 00 00 00 00 04 fa
0x0c08801fc180: fa fa 00 00 00 00 00 01 fa fa 00 00 00 00 00 01
0x0c08801fc190: fa fa 00 00 00 00 00 fa fa fa 00 00 00 00 04 fa
=>0x0c08801fc1a0: fa fa fd[fd]fd fd fd fa fa fa fd fd fd fd fd fa
0x0c08801fc1b0: fa fa fd fd fd fd fd fa fa fa fd fd fd fd fd fa
0x0c08801fc1c0: fa fa 00 00 00 00 00 fa fa fa fd fd fd fd fd fd
0x0c08801fc1d0: fa fa 00 00 00 00 00 01 fa fa fd fd fd fd fd fa
0x0c08801fc1e0: fa fa fd fd fd fd fd fa fa fa fd fd fd fd fd fd
0x0c08801fc1f0: fa fa 00 00 00 00 00 01 fa fa fd fd fd fd fd fa
Shadow byte legend (one shadow byte represents 8 application bytes):
Addressable: 00
Partially addressable: 01 02 03 04 05 06 07
Heap left redzone: fa
Freed heap region: fd
Stack left redzone: f1
Stack mid redzone: f2
Stack right redzone: f3
Stack after return: f5
Stack use after scope: f8
Global redzone: f9
Global init order: f6
Poisoned by user: f7
Container overflow: fc
Array cookie: ac
Intra object redzone: bb
ASan internal: fe
Left alloca redzone: ca
Right alloca redzone: cb
==7309==ABORTING
Signed-off-by: Li Feng <fengli@smartx.com>
Message-Id: <20200417101707.14467-1-fengli@smartx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
This patch introduces support for PMR that has been defined as part of NVMe 1.4
spec. User can now specify a pmrdev option that should point to HostMemoryBackend.
pmrdev memory region will subsequently be exposed as PCI BAR 2 in emulated NVMe
device. Guest OS can perform mmio read and writes to the PMR region that will stay
persistent across system reboot.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@linux.intel.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20200330164656.9348-1-andrzej.jakowski@linux.intel.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since 7f5d9b206d ("object-add: don't create return value if
failed"), qmp_object_add() don't write any value in 'ret_data', thus
has random data. Then qobject_unref() fails and abort().
Fix by initialising 'ret_data' properly.
Fixes: 5f07c4d60d ("qapi: Flatten object-add")
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200406164207.1446817-1-anthony.perard@citrix.com>
Commit a31ca6801c ("qemu/queue.h: clear linked list pointers on
remove") revealed that a request was removed twice from a list, once
in xen_block_finish_request() and a second time in
xen_block_release_request() when both function are called from
xen_block_complete_aio(). But also, the `requests_inflight' counter is
decreased twice, and thus became negative.
This is a bug that was introduced in bfd0d63660 ("xen-block: improve
response latency"), where a `finished' list was removed.
That commit also introduced a leak of request in xen_block_do_aio().
That function calls xen_block_finish_request() but the request is
never released after that.
To fix both issue, we do two changes:
- we squash finish_request() and release_request() together as we want
to remove a request from 'inflight' list to add it to 'freelist'.
- before releasing a request, we need to let the other end know the
result, thus we should call xen_block_send_response() before
releasing a request.
The first change fixes the double QLIST_REMOVE() as we remove the extra
call. The second change makes the leak go away because if we want to
call finish_request(), we need to call a function that does all of
finish, send response, and release.
Fixes: bfd0d63660 ("xen-block: improve response latency")
Signed-off-by: Anthony PERARD <anthony.perard@citrix.com>
Message-Id: <20200406140217.1441858-1-anthony.perard@citrix.com>
Reviewed-by: Paul Durrant <paul@xen.org>
[mreitz: Amended commit message as per Paul's suggestions]
Signed-off-by: Max Reitz <mreitz@redhat.com>
the G_IO_HUP is watched in tcp_chr_connect, and the callback
vhost_user_blk_watch is not needed, because tcp_chr_hup is registered as
callback. And it will close the tcp link.
Signed-off-by: Li Feng <fengli@smartx.com>
Message-Id: <20200323052924.29286-1-fengli@smartx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio_vqs forgot to free on the error path in realize(). Fix that.
The asan stack:
Direct leak of 14336 byte(s) in 1 object(s) allocated from:
#0 0x7f58b93fd970 in __interceptor_calloc (/lib64/libasan.so.5+0xef970)
#1 0x7f58b858249d in g_malloc0 (/lib64/libglib-2.0.so.0+0x5249d)
#2 0x5562cc627f49 in virtio_add_queue /mnt/sdb/qemu/hw/virtio/virtio.c:2413
#3 0x5562cc4b524a in virtio_blk_device_realize /mnt/sdb/qemu/hw/block/virtio-blk.c:1202
#4 0x5562cc613050 in virtio_device_realize /mnt/sdb/qemu/hw/virtio/virtio.c:3615
#5 0x5562ccb7a568 in device_set_realized /mnt/sdb/qemu/hw/core/qdev.c:891
#6 0x5562cd39cd45 in property_set_bool /mnt/sdb/qemu/qom/object.c:2238
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Pan Nengyuan <pannengyuan@huawei.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20200328005705.29898-2-pannengyuan@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
While working on the Tulip driver i tried to write some Teledisk images to
a floppy image which didn't work. Turned out that Teledisk checks the written
data by issuing a READ command to the FDC but running the DMA controller
in VERIFY mode. As we ignored the DMA request in that case, the DMA transfer
never finished, and Teledisk reported an error.
The i8257 spec says about verify transfers:
3) DMA verify, which does not actually involve the transfer of data. When an
8257 channel is in the DMA verify mode, it will respond the same as described
for transfer operations, except that no memory or I/O read/write control signals
will be generated.
Hervé proposed to remove all the dma_mode_ok stuff from fdc to have a more
clear boundary between DMA and FDC, so this patch also does that.
Suggested-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
The given argument for this trace should be cqid, not sqid.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Message-Id: <20200324140646.8274-1-minwoo.im.dev@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
While there, tidy up indentation, and add return just for consistency
and robustness.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20200313170517.22480-4-armbru@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[The "while there" cleanups squashed in]
Whenever an unsupported command is encountered, the current code
interprets each transferred byte as new command. Most of the time, those
'commands' are interpreted as new unknown commands. However, in rare
cases, it may be that for example address or length information
passed with the original command is by itself a valid command.
If that happens, the state machine may get completely confused and,
worst case, start writing data into the flash or even erase it.
To avoid the problem, transition into STATE_READING_DATA and keep
sending a value of 0 until the chip is deselected after encountering
an unsupported command.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When requesting JEDEC data using the JEDEC_READ command, the Linux kernel
always requests 6 bytes. The current implementation only returns three
bytes, and interprets the remaining three bytes as new commands.
While this does not matter most of the time, it is at the very least
confusing. To avoid the problem, always report up to 6 bytes of JEDEC
data. Fill remaining data with 0.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While at it, add some trace messages to help debug problems
seen when running the latest Linux kernel.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Mapping object-add to the command line as is doesn't result in nice
syntax because of the nesting introduced with 'props'. This becomes
nicer and more consistent with device_add and netdev_add when we accept
properties for the object on the top level instead.
'props' is still accepted after this patch, but marked as deprecated.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20200224143008.13362-8-kwolf@redhat.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* fix for xen-block
* fix in exec.c for migration of xen guest
* one cleanup patch
-----BEGIN PGP SIGNATURE-----
iQFOBAABCgA4FiEE+AwAYwjiLP2KkueYDPVXL9f7Va8FAl5XrpgaHGFudGhvbnku
cGVyYXJkQGNpdHJpeC5jb20ACgkQDPVXL9f7Va88wQf/TcU/rOJSIlTzIoIktp+T
uvsb3+TkppdLBeFvAPAfKXFG8JxO7RHxtnn7pZFdlejqNG+AJhARd+LbQMPMO15d
cLo7Da5HE8ni9f+CwtY61SNS3qe1+8qoNRFwxeycA5pfr+XZb5dB8FYW4w5H4mg0
gyf4R0kb/5Y43K4FKEu/09rh3jtV1HqVfbjMrk3u82sex5gp3LT9kg6VJyrGE3rr
D/rmVOM1+rEn8S9e5YG1YqBq1HRSMAbrQ3kvkCJPHE+vLnmkbITyi9faL99vR3Pl
oTtmnwNWUwYzf/FwAA+8/YaaAsEz17KQXOQtFxIC+j9im2KkE5waD15AfEJ5eQgW
EA==
=sKMx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/aperard/tags/pull-xen-20200227' into staging
Xen queue 2020-02-27
* fix for xen-block
* fix in exec.c for migration of xen guest
* one cleanup patch
# gpg: Signature made Thu 27 Feb 2020 11:57:12 GMT
# gpg: using RSA key F80C006308E22CFD8A92E7980CF5572FD7FB55AF
# gpg: issuer "anthony.perard@citrix.com"
# gpg: Good signature from "Anthony PERARD <anthony.perard@gmail.com>" [marginal]
# gpg: aka "Anthony PERARD <anthony.perard@citrix.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 5379 2F71 024C 600F 778A 7161 D8D5 7199 DF83 42C8
# Subkey fingerprint: F80C 0063 08E2 2CFD 8A92 E798 0CF5 572F D7FB 55AF
* remotes/aperard/tags/pull-xen-20200227:
Memory: Only call ramblock_ptr when needed in qemu_ram_writeback
xen-bus/block: explicitly assign event channels to an AioContext
hw/xen/xen_pt_load_rom: Remove unused includes
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
