Introduce a symbol which can be used to prevent display modules which
need vga support being loaded into system emulators with CONFIG_VGA=n.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-16-kraxel@redhat.com>
Now that we have separated the gl and non-gl code flows to two different
devices there is little reason turn on and off virglrenderer usage at
runtime. The gl code can simply use virglrenderer unconditionally.
So drop use_virgl_renderer field and just do that.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-13-kraxel@redhat.com>
Move device init (realize) and properties.
Drop the virgl property, the virtio-gpu-gl-device has virgl enabled no
matter what. Just use virtio-gpu-device instead if you don't want
enable virgl and opengl. This simplifies the logic and reduces the test
matrix.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-4-kraxel@redhat.com>
Just a skeleton for starters, following patches will add more code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-3-kraxel@redhat.com>
dma_memory_map() may map only a part of the request. Happens if the
request can't be mapped in one go, for example due to a iommu creating
a linear dma mapping for scattered physical pages. Should that be the
case virtio-gpu must call dma_memory_map() again with the remaining
range instead of simply throwing an error.
Note that this change implies the number of iov entries may differ from
the number of mapping entries sent by the guest. Therefore the iov_len
bookkeeping needs some updates too, we have to explicitly pass around
the iov length now.
Reported-by: Auger Eric <eric.auger@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210506091001.1301250-1-kraxel@redhat.com
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210506091001.1301250-1-kraxel@redhat.com>
Here's the first ppc pull request for qemu-6.1. It has a wide variety
of stuff accumulated during the 6.0 freeze. Highlights are:
* Multi-phase reset cleanups for PAPR
* Preliminary cleanups towards allowing !CONFIG_TCG for the ppc target
* Cleanup of AIL logic and extension to POWER10
* Further improvements to handling of hot unplug failures on PAPR
* Allow much larger numbers of CPU on pseries
* Support for the H_SCM_HEALTH hypercall
* Add support for the Pegasos II board
* Substantial cleanup to hflag handling
* Assorted minor fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=N0qr
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.1-20210504' into staging
ppc patch queue 2021-05-04
Here's the first ppc pull request for qemu-6.1. It has a wide variety
of stuff accumulated during the 6.0 freeze. Highlights are:
* Multi-phase reset cleanups for PAPR
* Preliminary cleanups towards allowing !CONFIG_TCG for the ppc target
* Cleanup of AIL logic and extension to POWER10
* Further improvements to handling of hot unplug failures on PAPR
* Allow much larger numbers of CPU on pseries
* Support for the H_SCM_HEALTH hypercall
* Add support for the Pegasos II board
* Substantial cleanup to hflag handling
* Assorted minor fixes and cleanups
# gpg: Signature made Tue 04 May 2021 06:52:39 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.1-20210504: (46 commits)
hw/ppc/pnv_psi: Use device_cold_reset() instead of device_legacy_reset()
hw/ppc/spapr_vio: Reset TCE table object with device_cold_reset()
hw/intc/spapr_xive: Use device_cold_reset() instead of device_legacy_reset()
target/ppc: removed VSCR from SPR registration
target/ppc: Reduce the size of ppc_spr_t
target/ppc: Clean up _spr_register et al
target/ppc: Add POWER10 exception model
target/ppc: rework AIL logic in interrupt delivery
target/ppc: move opcode table logic to translate.c
target/ppc: code motion from translate_init.c.inc to gdbstub.c
spapr_drc.c: handle hotunplug errors in drc_unisolate_logical()
spapr.h: increase FDT_MAX_SIZE
spapr.c: do not use MachineClass::max_cpus to limit CPUs
ppc: Rename current DAWR macros and variables
target/ppc: POWER10 supports scv
target/ppc: Fix POWER9 radix guest HV interrupt AIL behaviour
docs/system: ppc: Add documentation for ppce500 machine
roms/u-boot: Bump ppce500 u-boot to v2021.04 to fix broken pci support
roms/Makefile: Update ppce500 u-boot build directory name
ppc/spapr: Add support for implement support for H_SCM_HEALTH
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----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=aCeG
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.1-pull-request' into staging
Trivial patches pull request 20210503
# gpg: Signature made Mon 03 May 2021 09:34:56 BST
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.1-pull-request: (23 commits)
hw/rx/rx-gdbsim: Do not accept invalid memory size
docs: More precisely describe memory-backend-*::id's user
scripts: fix generation update-binfmts templates
docs/system: Document the removal of "compat" property for POWER CPUs
mc146818rtc: put it into the 'misc' category
Do not include exec/address-spaces.h if it's not really necessary
Do not include cpu.h if it's not really necessary
Do not include hw/boards.h if it's not really necessary
Do not include sysemu/sysemu.h if it's not really necessary
hw: Do not include qemu/log.h if it is not necessary
hw: Do not include hw/irq.h if it is not necessary
hw: Do not include hw/sysbus.h if it is not necessary
hw: Remove superfluous includes of hw/hw.h
ui: Fix memory leak in qemu_xkeymap_mapping_table()
hw/usb: Constify VMStateDescription
hw/display/qxl: Constify VMStateDescription
hw/arm: Constify VMStateDescription
vmstate: Constify some VMStateDescriptions
Fix typo in CFI build documentation
hw/pcmcia: Do not register PCMCIA type if not required
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fixes for the DMA space
* New model for ASPEED's Hash and Crypto Engine (Joel and Klaus)
* Acceptance tests (Joel)
* A fix for the XDMA model
* Some extra features for the SMC controller.
* Two new boards : rainier-bmc and quanta-q7l1-bmc (Patrick)
-----BEGIN PGP SIGNATURE-----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=N5Us
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20210503' into staging
Aspeed patches :
* Fixes for the DMA space
* New model for ASPEED's Hash and Crypto Engine (Joel and Klaus)
* Acceptance tests (Joel)
* A fix for the XDMA model
* Some extra features for the SMC controller.
* Two new boards : rainier-bmc and quanta-q7l1-bmc (Patrick)
# gpg: Signature made Mon 03 May 2021 06:23:36 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20210503:
aspeed: Add support for the quanta-q7l1-bmc board
hw/block: m25p80: Add support for mt25ql02g and mt25qu02g
aspeed: Add support for the rainier-bmc board
aspeed: Deprecate the swift-bmc machine
tests/qtest: Rename m25p80 test in aspeed_smc test
aspeed/smc: Add extra controls to request DMA
aspeed/smc: Add a 'features' attribute to the object class
hw/misc/aspeed_xdma: Add AST2600 support
tests/acceptance: Test ast2600 machine
tests/acceptance: Test ast2400 and ast2500 machines
tests/qtest: Add test for Aspeed HACE
aspeed: Integrate HACE
hw: Model ASPEED's Hash and Crypto Engine
hw/arm/aspeed: Do not sysbus-map mmio flash region directly, use alias
aspeed/i2c: Rename DMA address space
aspeed/i2c: Fix DMA address mask
aspeed/smc: Remove unused "sdram-base" property
aspeed/smc: Use the RAM memory region for DMAs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Right now, rate limiting is protected by the AioContext mutex, which is
taken for example both by the block jobs and by qmp_block_job_set_speed
(via find_block_job).
We would like to remove the dependency of block layer code on the
AioContext mutex, since most drivers and the core I/O code are already
not relying on it. However, there is no existing lock that can easily
be taken by both ratelimit_set_speed and ratelimit_calculate_delay,
especially because the latter might run in coroutine context (and
therefore under a CoMutex) but the former will not.
Since concurrent calls to ratelimit_calculate_delay are not possible,
one idea could be to use a seqlock to get a snapshot of slice_ns and
slice_quota. But for now keep it simple, and just add a mutex to the
RateLimit struct; block jobs are generally not performance critical to
the point of optimizing the clock cycles spent in synchronization.
This also requires the introduction of init/destroy functions, so
add them to the two users of ratelimit.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Certain SMP topologies stress, e.g. 1 thread/core, 2048 cores and
1 socket, stress the current maximum size of the pSeries FDT:
Calling ibm,client-architecture-support...qemu-system-ppc64: error
creating device tree: (fdt_setprop(fdt, offset,
"ibm,processor-segment-sizes", segs, sizeof(segs))): FDT_ERR_NOSPACE
2048 is the default NR_CPUS value for the pSeries kernel. It's expected
that users will want QEMU to be able to handle this kind of
configuration.
Bumping FDT_MAX_SIZE to 2MB is enough for these setups to be created.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210408204049.221802-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Power10 is introducing second DAWR. Use real register names (with
suffix 0) from ISA for current macros and variables used by Qemu.
One exception to this is KVM_REG_PPC_DAWR[X]. This is from kernel
uapi header and thus not changed in kernel as well as Qemu.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210412114433.129702-3-ravi.bangoria@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add support for H_SCM_HEALTH hcall described at [1] for spapr
nvdimms. This enables guest to detect the 'unarmed' status of a
specific spapr nvdimm identified by its DRC and if its unarmed, mark
the region backed by the nvdimm as read-only.
The patch adds h_scm_health() to handle the H_SCM_HEALTH hcall which
returns two 64-bit bitmaps (health bitmap, health bitmap mask) derived
from 'struct nvdimm->unarmed' member.
Linux kernel side changes to enable handling of 'unarmed' nvdimms for
ppc64 are proposed at [2].
References:
[1] "Hypercall Op-codes (hcalls)"
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/powerpc/papr_hcalls.rst#n220
[2] "powerpc/papr_scm: Mark nvdimm as unarmed if needed during probe"
https://lore.kernel.org/linux-nvdimm/20210329113103.476760-1-vaibhav@linux.ibm.com/
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Message-Id: <20210402102128.213943-1-vaibhav@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The Marvell Discovery II aka. MV64361 is a PowerPC system controller
chip that is used on the pegasos2 PPC board. This adds emulation of it
that models the device enough to boot guests on this board. The
mv643xx.h header with register definitions is taken from Linux 4.15.10
only fixing white space errors, removing not needed parts and changing
formatting for QEMU coding style.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <79545ebd03bfe0665b73d2d7cbc74fdf3d62629e.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add emulation of VT8231 south bridge ISA part based on the similar
VT82C686B but implemented in a separate subclass that holds the
differences while reusing parts that can be shared.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <10abc9f89854e7c980b9731c33d25a2e307e9c4f.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
To allow reusing ISA bridge emulation for vt8231_isa move the device
state of vt82c686b_isa emulation in an abstract via_isa class. This
change breaks migration back compatibility but this is not an issue
for Fuloong2E machine which is not versioned or migration supported.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <0cb8fc69c7aaa555589181931b881335fecd2ef3.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Collect superio functionality and its controlling config registers
handling in an abstract VIA_SUPERIO class that is a subclass of
ISA_SUPERIO and put vt82c686b specific parts in a subclass of this
abstract class.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <fbcc8cc8baf83f327612a1ef1c14bcbcdb0e7edb.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The include/hw/hw.h header only has a prototype for hw_error(),
so it does not make sense to include this in files that do not
use this function.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210326151848.2217216-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
When TCG is enabled, the accel/tcg/ include path is added to the
project global include search list. This accel/tcg/ directory
contains a header named "internal.h" which, while intented to
be internal to accel/tcg/, is accessible by all files compiled
when TCG is enabled. This might lead to problem with other
directories using the same "internal.h" header name:
$ git ls-files | fgrep /internal.h
accel/tcg/internal.h
include/hw/ide/internal.h
target/hexagon/internal.h
target/mips/internal.h
target/ppc/internal.h
target/s390x/internal.h
As we don't need to expose accel/tcg/ internals to the rest of
the code base, simplify by removing it from the include search
list, and include the accel/tcg/ public headers relative to the
project root search path (which is already in the generic include
search path).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Claudio Fontana <cfontana@suse.de>
Message-Id: <20210413081008.3409459-1-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The AST2600 SPI controllers have a set of bits to request/grant DMA
access. Add a new SMC feature for these controllers and use it to
check access to the DMA registers.
Cc: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210407171637.777743-16-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It will simplify extensions of the SMC model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210407171637.777743-15-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When we introduced support for the AST2600 SoC, the XDMA controller
was forgotten. It went unnoticed because it's not used under emulation.
But the register layout being different, the reset procedure is bogus
and this breaks kexec.
Add a AspeedXDMAClass to take into account the register differences.
Cc: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Message-Id: <20210407171637.777743-14-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add the hash and crypto engine model to the Aspeed socs.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210409000253.1475587-3-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The HACE (Hash and Crypto Engine) is a device that offloads MD5, SHA1,
SHA2, RSA and other cryptographic algorithms.
This initial model implements a subset of the device's functionality;
currently only MD5/SHA hashing, and on the ast2600's scatter gather
engine.
Co-developed-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
[ clg: - fixes for 32-bit and OSX builds ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210409000253.1475587-2-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The flash mmio region is exposed as an AddressSpace.
AddressSpaces must not be sysbus-mapped, therefore map
the region using an alias.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[ clg : Fix DMA_FLASH_ADDR() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210312182851.1922972-3-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210407171637.777743-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407171637.777743-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Normally, blk_new_open() just shares all permissions. This was fine
originally when permissions only protected against uses in the same
process because no other part of the code would actually get to access
the block nodes opened with blk_new_open(). However, since we use it for
file locking now, unsharing permissions becomes desirable.
Add a new BDRV_O_NO_SHARE flag that is used in blk_new_open() to unshare
any permissions that can be unshared.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210422164344.283389-2-kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Old interfaces dropped, nobody directly calls
bdrv_child_set_perm_abort() and bdrv_child_set_perm_commit(), so we can
use personal state structure for the action and stop exploiting
BdrvChild structure. Also, drop "_safe" suffix which is redundant now.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210428151804.439460-35-vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move bdrv_reopen_multiple to new paradigm of permission update:
first update graph relations, then do refresh the permissions.
We have to modify reopen process in file-posix driver: with new scheme
we don't have prepared permissions in raw_reopen_prepare(), so we
should reconfigure fd in raw_check_perm(). Still this seems more native
and simple anyway.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210428151804.439460-31-vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
To be used in further commit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210428151804.439460-28-vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Using bdrv_replace_node() for removing filter is not good enough: it
keeps child reference of the filter, which may conflict with original
top node during permission update.
Instead let's create new interface, which will do all graph
modifications first and then update permissions.
Let's modify bdrv_replace_node_common(), allowing it additionally drop
backing chain child link pointing to new node. This is quite
appropriate for bdrv_drop_intermediate() and makes possible to add
new bdrv_drop_filter() as a simple wrapper.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210428151804.439460-24-vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add simple transaction API to use in further update of block graph
operations.
Supposed usage is:
- "prepare" is main function of the action and it should make the main
effect of the action to be visible for the following actions, keeping
possibility of roll-back, saving necessary things in action state,
which is prepended to the action list (to do that, prepare func
should call tran_add()). So, driver struct doesn't include "prepare"
field, as it is supposed to be called directly.
- commit/rollback is supposed to be called for the list of action
states, to commit/rollback all the actions in reverse order
- When possible "commit" should not make visible effect for other
actions, which make possible transparent logical interaction between
actions.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210428151804.439460-9-vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
These functions are called only from bdrv_reopen_multiple() in block.c.
No reason to publish them.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210428151804.439460-8-vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Passing parent aio context is redundant, as child_class and parent
opaque pointer are enough to retrieve it. Drop the argument and use new
bdrv_child_get_parent_aio_context() interface.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210428151804.439460-7-vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Add new handler to get aio context and implement it in all child
classes. Add corresponding public interface to be used soon.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210428151804.439460-6-vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Currently the gpex PCI controller implements no special behaviour for
guest accesses to areas of the PIO and MMIO where it has not mapped
any PCI devices, which means that for Arm you end up with a CPU
exception due to a data abort.
Most host OSes expect "like an x86 PC" behaviour, where bad accesses
like this return -1 for reads and ignore writes. In the interests of
not being surprising, make host CPU accesses to these windows behave
as -1/discard where there's no mapped PCI device.
The old behaviour generally didn't cause any problems, because
almost always the guest OS will map the PCI devices and then only
access where it has mapped them. One corner case where you will see
this kind of access is if Linux attempts to probe legacy ISA
devices via a PIO window access. So far the only case where we've
seen this has been via the syzkaller fuzzer.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210325163315.27724-1-peter.maydell@linaro.org
Fixes: https://bugs.launchpad.net/qemu/+bug/1918917
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There could be case that peer is NULL. This can happen when during
network device hot-add where net device needs to be added first. So
the patch check the existence of peer before trying to do the pad.
Fixes: 969e50b61a ("net: Pad short frames to minimum size before sending from SLiRP/TAP")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Message-id: 20210423031803.1479-1-jasowang@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Mostly osdep.h puts the system includes at the top of the file; but
there are a couple of exceptions where we include a system header
halfway through the file. Move these up to the top with the rest
so that all the system headers we include are included before
we include os-win32.h or os-posix.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210416135543.20382-4-peter.maydell@linaro.org
Message-id: 20210414184343.26235-1-peter.maydell@linaro.org
System headers may include templates if compiled with a C++ compiler,
which cause the compiler to complain if qemu/osdep.h is included
within a C++ source file's 'extern "C"' block. Add
an 'extern "C"' block directly to qemu/osdep.h, so that
system headers can be kept out of it.
There is a stray declaration early in qemu/osdep.h, which needs
to be special cased. Add a definition in qemu/compiler.h to
make it look nice.
config-host.h, CONFIG_TARGET, exec/poison.h and qemu/compiler.h
are included outside the 'extern "C"' block; that is not
an issue because they consist entirely of preprocessor directives.
This allows us to move the include of osdep.h in our two C++
source files outside the extern "C" block they were previously
using for it, which in turn means that they compile successfully
against newer versions of glib which insist that glib.h is
*not* inside an extern "C" block.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210416135543.20382-3-peter.maydell@linaro.org
[PMM: Moved disas/arm-a64.cc osdep.h include out of its extern "C" block;
explained in commit message why we're doing this]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
glib-compat.h is sort of like a system header, and it needs to include
system headers (glib.h) that may dislike being included under
'extern "C"'. Move it right after all system headers and before
all other QEMU headers.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210416135543.20382-2-peter.maydell@linaro.org
[PMM: Added comment about why glib-compat.h is special]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The pca954x is an i2c mux, and this adds support for two variants of
this device: the pca9546 and pca9548.
This device is very common on BMCs to route a different channel to each
PCIe i2c bus downstream from the BMC.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-Id: <20210412194522.664594-5-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Moves the search for matching devices on an i2c bus into a separate
method. This allows for an object that owns an I2CBus can avoid
duplicating this method.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-4-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
At the start of an i2c transaction, the i2c bus searches its list of
children to identify which devices correspond to the address (or
broadcast). Now the I2CSlave device has a method "match" that
encapsulates the lookup behavior. This allows the behavior to be changed
to support devices, such as i2c muxes.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-3-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
To enable passing the current_devs field as a parameter, we need to use
a named struct type.
Tested: BMC firmware with i2c devices booted to userspace.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210412194522.664594-2-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Here's what I hope is the last ppc related pull request for qemu-6.0.
The 2 patches here revert a behavioural change that after further
discussion we concluded was a bad idea (adding a timeout for
possibly-failed hot unplug requests). Instead it implements a
different approach to the original problem: we again let unplug
requests the guest doesn't respond to remain pending indefinitely, but
no longer allow those to block attempts to retry the same unplug
again.
The change is a bit more complex than I'd like for this late in the
freeze. Nonetheless, I think it's important to merge this for 6.0, so
we don't allow a release which has the probably-a-bad-idea timeout
behaviour.
-----BEGIN PGP SIGNATURE-----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=fIJT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.0-20210412' into staging
ppc patch queue for 2021-04-21
Here's what I hope is the last ppc related pull request for qemu-6.0.
The 2 patches here revert a behavioural change that after further
discussion we concluded was a bad idea (adding a timeout for
possibly-failed hot unplug requests). Instead it implements a
different approach to the original problem: we again let unplug
requests the guest doesn't respond to remain pending indefinitely, but
no longer allow those to block attempts to retry the same unplug
again.
The change is a bit more complex than I'd like for this late in the
freeze. Nonetheless, I think it's important to merge this for 6.0, so
we don't allow a release which has the probably-a-bad-idea timeout
behaviour.
# gpg: Signature made Mon 12 Apr 2021 06:25:58 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.0-20210412:
spapr.c: always pulse guest IRQ in spapr_core_unplug_request()
spapr: rollback 'unplug timeout' for CPU hotunplugs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If QEMU is launched with the -S option then the ESPState mig_version_id property
is left unset due to the ordering of the VMState fields in the VMStateDescription
for sysbusespscsi and pciespscsi. If the VM is migrated and restored in this
stopped state, the version tests in the vmstate_esp VMStateDescription and
esp_post_load() become confused causing the migration to fail.
Fix the ordering problem by moving the setting of mig_version_id to a common
esp_pre_save() function which is invoked first by both sysbusespscsi and
pciespscsi rather than at the point where ESPState is itself serialised into the
migration stream.
Buglink: https://bugs.launchpad.net/qemu/+bug/1922611
Fixes: 0bd005be78 ("esp: add vmstate_esp version to embedded ESPState")
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210407124842.32695-1-mark.cave-ayland@ilande.co.uk>
Unfortuately, the elements of PAGE_* were not in numerical
order and so PAGE_ANON was added to an "unused" bit.
As an arbitrary choice, move PAGE_TARGET_{1,2} together.
Cc: Laurent Vivier <laurent@vivier.eu>
Fixes: 26bab757d4 ("linux-user: Introduce PAGE_ANON")
Buglink: https://bugs.launchpad.net/bugs/1922617
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The pseries machines introduced the concept of 'unplug timeout' for CPU
hotunplugs. The idea was to circunvent a deficiency in the pSeries
specification (PAPR), that currently does not define a proper way for
the hotunplug to fail. If the guest refuses to release the CPU (see [1]
for an example) there is no way for QEMU to detect the failure.
Further discussions about how to send a QAPI event to inform about the
hotunplug timeout [2] exposed problems that weren't predicted back when
the idea was developed. Other QEMU machines don't have any type of
hotunplug timeout mechanism for any device, e.g. ACPI based machines
have a way to make hotunplug errors visible to the hypervisor. This
would make this timeout mechanism exclusive to pSeries, which is not
ideal.
The real problem is that a QAPI event that reports hotunplug timeouts
puts the management layer (namely Libvirt) in a weird spot. We're not
telling that the hotunplug failed, because we can't be 100% sure of
that, and yet we're resetting the unplug state back, preventing any
DEVICE_DEL events to reach out in case the guest decides to release the
device. Libvirt would need to inspect the guest itself to see if the
device was released or not, otherwise the internal domain states will be
inconsistent. Moreover, Libvirt already has an 'unplug timeout'
concept, and a QEMU side timeout would need to be juggled together with
the existing Libvirt timeout.
All this considered, this solution ended up creating more trouble than
it solved. This patch reverts the 3 commits that introduced the timeout
mechanism for CPU hotplugs in pSeries machines.
This reverts commit 4515a5f786
"qemu_timer.c: add timer_deadline_ms() helper"
This reverts commit d1c2e3ce3d
"spapr_drc.c: add hotunplug timeout for CPUs"
This reverts commit 51254ffb32
"spapr_drc.c: introduce unplug_timeout_timer"
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1911414
[2] https://lists.gnu.org/archive/html/qemu-devel/2021-03/msg04682.html
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210401000437.131140-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Version: GnuPG v1
iQEcBAABAgAGBQJgbs4gAAoJEO8Ells5jWIRvgAIAJjpj9ptxEfEAisTeU7IMNPk
vFyf9aBj/QBPv8VmcC90Mz/x38bMn0zE6V9E53camA7s1YtLxWj5ZG9wvj0ExJB9
jgk4kEm5gpj8LY7/GwECNffaITQtLZgE4HVP98dVG9o1+5iCkZf8RnXAQH2ckzTs
WoYuM0Glgj0XXdBauvpEkidQ+q23cOw7ipxNseI5wxZBAZt0RGdXoO6Dh+S219ro
kFoDwzZS9tnuwpzzZJefQJuRWkUm1LsZ6rwC7Yd+gpk2Yt+fLGihF4dc0se2+SE1
jeq7fV1E62PvEs2GJx4hs3rqakcBDE4Bf83sZnbFKMVpuvFUh+mXcKaIfXABDi8=
=3d/N
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Thu 08 Apr 2021 10:34:24 BST
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
tap-win32: correctly recycle buffers
Revert "qapi: net: Add query-netdev command"
Revert "tests: Add tests for query-netdev command"
Revert "net: Move NetClientState.info_str to dynamic allocations"
Revert "hmp: Use QAPI NetdevInfo in hmp_info_network"
Revert "net: Do not fill legacy info_str for backends"
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A seg fix in virtiofsd, a bunch of fixes for background snapshots, and
a migration test fix.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
v2
Fix for !linux build
-----BEGIN PGP SIGNATURE-----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=FKJ4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert/tags/pull-migration-20210407b' into staging
V2 migration+virtiofs fixes pull 2021-04-07
A seg fix in virtiofsd, a bunch of fixes for background snapshots, and
a migration test fix.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
v2
Fix for !linux build
# gpg: Signature made Wed 07 Apr 2021 18:53:13 BST
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert/tags/pull-migration-20210407b:
tests/migration: fix parameter of auto-converge migration
migration: Rename 'bs' to 'block' in background snapshot code
migration: Pre-fault memory before starting background snasphot
migration: Inhibit virtio-balloon for the duration of background snapshot
migration: Fix missing qemu_fflush() on buffer file in bg_migration_thread
virtiofsd: Fix security.capability comparison
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Several issues has been reported for query-netdev series. Consider
it's late in the rc, this reverts commit
d32ad10a14.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Several issues has been reported for query-netdev info
series. Consider it's late in the rc, this reverts commit
commit 59b5437eb7.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Several issues has been reported for query-netdev info
series. Consider it's late in the rc, this reverts commit
a0724776c5.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Prior to this patch, if a private nvme-ns device (that is, a namespace
that is not linked to a subsystem) is wired up to an nvme-subsys linked
nvme controller device, the device fails to verify that the namespace id
is unique within the subsystem. NVM Express v1.4b, Section 6.1.6 ("NSID
and Namespace Usage") states that because the device supports Namespace
Management, "NSIDs *shall* be unique within the NVM subsystem".
Additionally, prior to this patch, private namespaces are not known to
the subsystem and the namespace is considered exclusive to the
controller with which it is initially wired up to. However, this is not
the definition of a private namespace; per Section 1.6.33 ("private
namespace"), a private namespace is just a namespace that does not
support multipath I/O or namespace sharing, which means "that it is only
able to be attached to one controller at a time".
Fix this by always allocating namespaces in the subsystem (if one is
linked to the controller), regardless of the shared/private status of
the namespace. Whether or not the namespace is shareable is controlled
by a new `shared` nvme-ns parameter.
Finally, this fix allows the nvme-ns `subsys` parameter to be removed,
since the `shared` parameter now serves the purpose of attaching the
namespace to all controllers in the subsystem upon device realization.
It is invalid to have an nvme-ns namespace device with a linked
subsystem without the parent nvme controller device also being linked to
one and since the nvme-ns devices will unconditionally be "attached" (in
QEMU terms that is) to an nvme controller device through an NvmeBus, the
nvme-ns namespace device can always get a reference to the subsystem of
the controller it is explicitly (using 'bus=' parameter) or implicitly
attaching to.
Fixes: e570768566 ("hw/block/nvme: support for shared namespace in subsystem")
Cc: Minwoo Im <minwoo.im.dev@gmail.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
The same thing as for incoming postcopy - we cannot deal with concurrent
RAM discards when using background snapshot feature in outgoing migration.
Fixes: 8518278a6a (migration: implementation
of background snapshot thread)
Signed-off-by: Andrey Gruzdev <andrey.gruzdev@virtuozzo.com>
Reported-by: David Hildenbrand <david@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210401092226.102804-3-andrey.gruzdev@virtuozzo.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
-----BEGIN PGP SIGNATURE-----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=f0Ad
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210406' into staging
target-arm queue:
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
# gpg: Signature made Tue 06 Apr 2021 13:25:54 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210406:
Remove myself as i.mx31 maintainer
Revert "target/arm: Make number of counters in PMCR follow the CPU"
hw/ppc/e500plat: Only try to add valid dynamic sysbus devices to platform bus
hw/arm/virt: Only try to add valid dynamic sysbus devices to platform bus
machine: Provide a function to check the dynamic sysbus allowlist
include/hw/boards.h: Document machine_class_allow_dynamic_sysbus_dev()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 4c70875372 ("pci: advertise a page aligned ATS") advertises
the page aligned via ATS capability (RO) to unbrek recent Linux IOMMU
drivers since 5.2. But it forgot the compat the capability which
breaks the migration from old machine type:
(qemu) qemu-kvm: get_pci_config_device: Bad config data: i=0x104 read:
0 device: 20 cmask: ff wmask: 0 w1cmask:0
This patch introduces a new parameter "x-ats-page-aligned" for
virtio-pci device and turns it on for machine type which is newer than
5.1.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: qemu-stable@nongnu.org
Fixes: 4c70875372 ("pci: advertise a page aligned ATS")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210406040330.11306-1-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Provide a new function dynamic_sysbus_dev_allowed() which checks the
per-machine list of permitted dynamic sysbus devices and returns a
boolean result indicating whether the device is allowed. We can use
this in the implementation of validate_sysbus_device(), but we will
also need it so that machine hotplug callbacks can validate devices
rather than assuming that any sysbus device might be hotpluggable
into the platform bus.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325153310.9131-3-peter.maydell@linaro.org
The function machine_class_allow_dynamic_sysbus_dev() is currently
undocumented; add a doc comment.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325153310.9131-2-peter.maydell@linaro.org
After introducing non-scalar machine properties, it would be preferrable
to have a single acpitable property which includes both generic
information (such as the OEM ids) and custom tables currently
passed via -acpitable.
Do not saddle ourselves with legacy oem-id and oem-table-id
properties, instead mark them as experimental.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210402082128.13854-1-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
V2:
- "tests: Add tests for yank with the chardev-change case" updated
- drop the readthedoc theme patch
-----BEGIN PGP SIGNATURE-----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=UwXe
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/marcandre/tags/for-6.0-pull-request' into staging
For 6.0 misc patches under my radar.
V2:
- "tests: Add tests for yank with the chardev-change case" updated
- drop the readthedoc theme patch
# gpg: Signature made Thu 01 Apr 2021 12:54:52 BST
# gpg: using RSA key 87A9BD933F87C606D276F62DDAE8E10975969CE5
# gpg: issuer "marcandre.lureau@redhat.com"
# gpg: Good signature from "Marc-André Lureau <marcandre.lureau@redhat.com>" [full]
# gpg: aka "Marc-André Lureau <marcandre.lureau@gmail.com>" [full]
# Primary key fingerprint: 87A9 BD93 3F87 C606 D276 F62D DAE8 E109 7596 9CE5
* remotes/marcandre/tags/for-6.0-pull-request:
tests: Add tests for yank with the chardev-change case
chardev: Fix yank with the chardev-change case
chardev/char.c: Always pass id to chardev_new
chardev/char.c: Move object_property_try_add_child out of chardev_new
yank: Always link full yank code
yank: Remove dependency on qiochannel
docs: simplify each section title
dbus-vmstate: Increase the size of input stream buffer used during load
util: fix use-after-free in module_load_one
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When changing from chardev-socket (which supports yank) to
chardev-socket again, it fails, because the new chardev attempts
to register a new yank instance. This in turn fails, as there
still is the yank instance from the current chardev. Also,
the old chardev shouldn't unregister the yank instance when it
is freed.
To fix this, now the new chardev only registers a yank instance if
the current chardev doesn't support yank and thus hasn't registered
one already. Also, when the old chardev is freed, it now only
unregisters the yank instance if the new chardev doesn't need it.
If the initialization of the new chardev fails, it still has
chr->handover_yank_instance set and won't unregister the yank
instance when it is freed.
s->registered_yank is always true here, as chardev-change only works
on user-visible chardevs and those are guraranteed to register a
yank instance as they are initialized via
chardev_new()
qemu_char_open()
cc->open() (qmp_chardev_open_socket()).
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Tested-by: Li Zhang <li.zhang@cloud.ionos.com>
Message-Id: <9637888d7591d2971975188478bb707299a1dc04.1617127849.git.lukasstraub2@web.de>
Remove dependency on qiochannel by removing yank_generic_iochannel and
letting migration and chardev use their own yank function for
iochannel.
Signed-off-by: Lukas Straub <lukasstraub2@web.de>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20ff143fc2db23e27cd41d38043e481376c9cec1.1616521341.git.lukasstraub2@web.de>
A fix for VDI image files and more generally for CoRwlock.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEhpWov9P5fNqsNXdanKSrs4Grc8gFAmBkRe8ACgkQnKSrs4Gr
c8g2EAf9Eq81Ve816xZTUc/2FzC0HGKxPehNkdbCBLbX/a+HgYQEUALFP6Lzfvud
D1rF2bcVTpPUdvpW2UebIyQcLqRH80q1Ba9VhuA99FAYeryg+xVcRFLbHgKfticT
omKSc9yrwJgKJXRZodSsggVBPjsCmhfClO0kA4nGLEywmZbr7i1L/fcbUPI68cOr
5Lv19UDjTIgaGCt0oJN9x/W7FKzz53tBOkGKqmQd2ZEq4LmIlObFQq7ZIHRejneU
76PDPiNRM4Y6fotXl91vMjCZykihuf8FYncXWhnHIOdUxUPQge2SCXhRe16bCEVG
y/6keiV9U3CfsSCHuLK85QnBQKrTPg==
=T9vh
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanha-gitlab/tags/block-pull-request' into staging
Pull request
A fix for VDI image files and more generally for CoRwlock.
# gpg: Signature made Wed 31 Mar 2021 10:50:39 BST
# gpg: using RSA key 8695A8BFD3F97CDAAC35775A9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>" [full]
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>" [full]
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha-gitlab/tags/block-pull-request:
test-coroutine: Add rwlock downgrade test
test-coroutine: Add rwlock upgrade test
coroutine-lock: Reimplement CoRwlock to fix downgrade bug
coroutine-lock: Store the coroutine in the CoWaitRecord only once
block/vdi: Don't assume that blocks are larger than VdiHeader
block/vdi: When writing new bmap entry fails, don't leak the buffer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An invariant of the current rwlock is that if multiple coroutines hold a
reader lock, all must be runnable. The unlock implementation relies on
this, choosing to wake a single coroutine when the final read lock
holder exits the critical section, assuming that it will wake a
coroutine attempting to acquire a write lock.
The downgrade implementation violates this assumption by creating a
read lock owning coroutine that is exclusively runnable - any other
coroutines that are waiting to acquire a read lock are *not* made
runnable when the write lock holder converts its ownership to read
only.
More in general, the old implementation had lots of other fairness bugs.
The root cause of the bugs was that CoQueue would wake up readers even
if there were pending writers, and would wake up writers even if there
were readers. In that case, the coroutine would go back to sleep *at
the end* of the CoQueue, losing its place at the head of the line.
To fix this, keep the queue of waiters explicitly in the CoRwlock
instead of using CoQueue, and store for each whether it is a
potential reader or a writer. This way, downgrade can look at the
first queued coroutines and wake it only if it is a reader, causing
all other readers in line to be released in turn.
Reported-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: David Edmondson <david.edmondson@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 20210325112941.365238-5-pbonzini@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
There is no H_REGISTER_PROCESS_TABLE, it is H_REGISTER_PROC_TBL handler
for which is still called h_register_process_table() though.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20210225032335.64245-1-aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The definition S390_ADAPTER_SUPPRESSIBLE was moved to "cpu.h", per
suggestion of Thomas Huth. From interface design perspective, IMHO, not
a good thing as it belongs to the public interface of
css_register_io_adapters(). We did this because CONFIG_KVM requeires
NEED_CPU_H and Thomas, and other commenters did not like the
consequences of that.
Moving the interrupt related declarations to s390_flic.h was suggested
by Cornelia Huck.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20210317095622.2839895-2-kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Similarly to 5f629d943c ("s390x: fix s390 virtio aliases"),
define the virtio aliases.
This allows to start machines with virtio devices without
knowledge of the implementation type.
For instance, we can use "-device virtio-scsi" on
m68k, s390x or PC, and the device will be respectively
"virtio-scsi-device", "virtio-scsi-ccw" or "virtio-scsi-pci".
This already exists for s390x and -ccw interfaces, add them
for m68k and MMIO (-device) interfaces.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20210319202335.2397060-3-laurent@vivier.eu>
Message-Id: <20210323165308.15244-18-alex.bennee@linaro.org>
This is used to define virtio-*-pci and virtio-*-ccw aliases
rather than substracting the CCW architecture from all the others.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Message-Id: <20210319202335.2397060-2-laurent@vivier.eu>
Message-Id: <20210323165308.15244-17-alex.bennee@linaro.org>
In bbc17caf81, we used an alias attribute to allow target_page
to be declared const, and yet be initialized late.
This fails when using LTO with several versions of gcc.
The compiler looks through the alias and decides that the const
variable is statically initialized to zero, then propagates that
zero to many uses of the variable.
This can be avoided by compiling one object file with -fno-lto.
In this way, any initializer cannot be seen, and the constant
propagation does not occur.
Since we are certain to have this separate compilation unit, we
can drop the alias attribute as well. We simply have differing
declarations for target_page in different compilation units.
Drop the use of init_target_page, and drop the configure detection
for CONFIG_ATTRIBUTE_ALIAS.
In order to change the compilation flags for a file with meson,
we must use a static_library. This runs into specific_ss, where
we would need to create many static_library instances.
Fix this by splitting page-vary.c: the page-vary-common.c part is
compiled once as a static_library, while the page-vary.c part is
left in specific_ss in order to handle the target-specific value
of TARGET_PAGE_BITS_MIN.
Reported-by: Gavin Shan <gshan@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210321211534.2101231-1-richard.henderson@linaro.org>
[PMD: Fix typo in subject, split original patch in 3]
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Gavin Shan <gshan@redhat.com>
Message-Id: <20210322112427.4045204-4-f4bug@amsat.org>
[rth: Update MAINTAINERS]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
In the next commit we will extract the generic code out of
page-vary.c, only keeping the target specific code. Both
files will use the same TargetPageBits structure, so make
its declaration in a shared header.
As the common header can not use target specific types,
use a uint64_t to hold the page mask value, and add a
cast back to target_long in the TARGET_PAGE_MASK definitions.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210322112427.4045204-3-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This PR includes:
- Fix for vector CSR access
- Improvements to the Ibex UART device
- PMP improvements and bug fixes
- Hypervisor extension bug fixes
- ramfb support for the virt machine
- Fast read support for SST flash
- Improvements to the microchip_pfsoc machine
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmBZSuUACgkQIeENKd+X
cFQfqggAqiTI/KYe5GW9WBrPpGdctuEgUVBbxUhq5zY52mVGTfqEn4LbCfvdaTOp
O1MA+kfi4JN87VVWCfHPH0S725qmaPV7wfpWKi8KcPQ9uR+4RvjX/RDptkZhVjC9
Ok9p6dg2cUbz9Jm/q2V1Z69fRNMrz6pJWPxfZeTpy9bcmFNyYBR9+xiSXaW2fuAM
HsyZbsP8zHmHxfGcZwI6vpSZh3P4Ytd6nL/8v98i1DwWUsf51TsEwaS87gRQSjTz
SHqHZ9xsVM0k3glFi+El39iHzpujlONkYPvZaFP8kRhzXtaWVP1cu+CaKNUPEteq
jWNHLwFQk9VcN8uDG5o0unGEXnLJPA==
=dKa4
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20210322-2' into staging
RISC-V PR for 6.0
This PR includes:
- Fix for vector CSR access
- Improvements to the Ibex UART device
- PMP improvements and bug fixes
- Hypervisor extension bug fixes
- ramfb support for the virt machine
- Fast read support for SST flash
- Improvements to the microchip_pfsoc machine
# gpg: Signature made Tue 23 Mar 2021 01:56:53 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210322-2:
target/riscv: Prevent lost illegal instruction exceptions
docs/system: riscv: Add documentation for 'microchip-icicle-kit' machine
hw/riscv: microchip_pfsoc: Map EMMC/SD mux register
hw/block: m25p80: Support fast read for SST flashes
target/riscv: Add proper two-stage lookup exception detection
target/riscv: Fix read and write accesses to vsip and vsie
hw/riscv: allow ramfb on virt
hw/riscv: Add fw_cfg support to virt
target/riscv: Use background registers also for MSTATUS_MPV
target/riscv: Make VSTIP and VSEIP read-only in hip
target/riscv: Adjust privilege level for HLV(X)/HSV instructions
target/riscv: flush TLB pages if PMP permission has been changed
target/riscv: add log of PMP permission checking
target/riscv: propagate PMP permission to TLB page
hw/char: disable ibex uart receive if the buffer is full
target/riscv: fix vs() to return proper error code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For accesses to rom blob data before or during reset, we have a
function rom_ptr() which looks for a rom blob that would be loaded to
the specified address, and returns a pointer into the rom blob data
corresponding to that address. This allows board or CPU code to say
"what is the data that is going to be loaded to this address?".
However, this function does not take account of memory region
aliases. If for instance a machine model has RAM at address
0x0000_0000 which is aliased to also appear at 0x1000_0000, a
rom_ptr() query for address 0x0000_0000 will only return a match if
the guest image provided by the user was loaded at 0x0000_0000 and
not if it was loaded at 0x1000_0000, even though they are the same
RAM and a run-time guest CPU read of 0x0000_0000 will read the data
loaded to 0x1000_0000.
Provide a new function rom_ptr_for_as() which takes an AddressSpace
argument, so that it can check whether the MemoryRegion corresponding
to the address is also mapped anywhere else in the AddressSpace and
look for rom blobs that loaded to that alias.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210318174823.18066-5-peter.maydell@linaro.org
The function flatview_for_each_range() calls a callback for each
range in a FlatView. Currently the callback gets the start and
length of the range and the MemoryRegion involved, but not the offset
within the MemoryRegion. Add this to the callback's arguments; we're
going to want it for a new use in the next commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210318174823.18066-4-peter.maydell@linaro.org
Add a documentation comment describing flatview_for_each_range().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210318174823.18066-3-peter.maydell@linaro.org
The return value of the flatview_cb callback passed to the
flatview_for_each_range() function is zero if the iteration through
the ranges should continue, or non-zero to break out of it. Use a
bool for this rather than int.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210318174823.18066-2-peter.maydell@linaro.org
A clock is added by commit aac63e0e6e ("hw/char/pl011: add a clock
input") since v5.2.0 which corresponds to virt-5.2 machine type. It
causes backwards migration failure from upstream to downstream (v5.1.0)
when the machine type is specified with virt-5.1.
This fixes the issue by following instructions from section "Connecting
subsections to properties" in docs/devel/migration.rst. With this applied,
the PL011 clock is migrated based on the machine type.
virt-5.2 or newer: migration
virt-5.1 or older: non-migration
Cc: qemu-stable@nongnu.org # v5.2.0+
Fixes: aac63e0e6e ("hw/char/pl011: add a clock input")
Suggested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20210318023801.18287-1-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The function is_surface_bgr() is no longer used anywhere,
so we can delete it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210314163927.1184-1-peter.maydell@linaro.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch add vnc_display_reload_certs() to support
update x509 certificates.
Signed-off-by: Zihao Chang <changzihao1@huawei.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210316075845.1476-3-changzihao1@huawei.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds reload interface for QCryptoTLSCredsClass and implements
the interface for QCryptoTLSCredsX509.
Signed-off-by: Zihao Chang <changzihao1@huawei.com>
Acked-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20210316075845.1476-2-changzihao1@huawei.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Since HSS commit c20a89f8dcac, the Icicle Kit reference design has
been updated to use a register mapped at 0x4f000000 instead of a
GPIO to control whether eMMC or SD card is to be used. With this
support the same HSS image can be used for both eMMC and SD card
boot flow, while previously two different board configurations were
used. This is undocumented but one can take a look at the HSS code
HSS_MMCInit() in services/mmc/mmc_api.c.
With this commit, HSS image built from 2020.12 release boots again.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210322075248.136255-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Provides fw_cfg for the virt machine on riscv. This enables
using e.g. ramfb later.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210318235041.17175-2-ashe@kivikakk.ee
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Not disabling the UART leads to QEMU overwriting the UART receive buffer with
the newest received byte. The rx_level variable is added to allow the use of
the existing OpenTitan driver libraries.
Signed-off-by: Alexander Wagner <alexander.wagner@ulal.de>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210309152130.13038-1-alexander.wagner@ulal.de
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The code that sets/gets oem fields is duplicated in both PC and MICROVM
variants. This commit moves it to X86MachineState so that all x86
variants can use it and duplication is removed.
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Message-Id: <20210221001737.24499-2-posteuca@mutex.one>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
We want to have safety margins for all tables based on the table type.
Let's move the maximum size logic into acpi_add_rom_blob() and make it
dependent on the table name, so we don't have to replicate for each and
every instance that creates such tables.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-4-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The resizeable memory region / RAMBlock that is created for the cmd blob
has a maximum size of whole host pages (e.g., 4k), because RAMBlocks
work on full host pages. In addition, in i386 ACPI code:
acpi_align_size(tables->linker->cmd_blob, ACPI_BUILD_ALIGN_SIZE);
makes sure to align to multiples of 4k, padding with 0.
For example, if our cmd_blob is created with a size of 2k, the maximum
size is 4k - we cannot grow beyond that. Growing might be required
due to guest action when rebuilding the tables, but also on incoming
migration.
This automatic generation of the maximum size used to be sufficient,
however, there are cases where we cross host pages now when growing at
runtime: we exceed the maximum size of the RAMBlock and can crash QEMU when
trying to resize the resizeable memory region / RAMBlock:
$ build/qemu-system-x86_64 --enable-kvm \
-machine q35,nvdimm=on \
-smp 1 \
-cpu host \
-m size=2G,slots=8,maxmem=4G \
-object memory-backend-file,id=mem0,mem-path=/tmp/nvdimm,size=256M \
-device nvdimm,label-size=131072,memdev=mem0,id=nvdimm0,slot=1 \
-nodefaults \
-device vmgenid \
-device intel-iommu
Results in:
Unexpected error in qemu_ram_resize() at ../softmmu/physmem.c:1850:
qemu-system-x86_64: Size too large: /rom@etc/table-loader:
0x2000 > 0x1000: Invalid argument
In this configuration, we consume exactly 4k (32 entries, 128 bytes each)
when creating the VM. However, once the guest boots up and maps the MCFG,
we also create the MCFG table and end up consuming 2 additional entries
(pointer + checksum) -- which is where we try resizing the memory region
/ RAMBlock, however, the maximum size does not allow for it.
Currently, we get the following maximum sizes for our different
mutable tables based on behavior of resizeable RAMBlock:
hw table max_size
------- ---------------------------------------------------------
virt "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
virt "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
virt "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
i386 "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
microvm "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
Let's set the maximum table size for "etc/table-loader" to 64k, so we
can properly grow at runtime, which should be good enough for the future.
Migration is not concerned with the maximum size of a RAMBlock, only
with the used size - so existing setups are not affected. Of course, we
cannot migrate a VM that would have crash when started on older QEMU from
new QEMU to older QEMU without failing early on the destination when
synchronizing the RAM state:
qemu-system-x86_64: Size too large: /rom@etc/table-loader: 0x2000 > 0x1000: Invalid argument
qemu-system-x86_64: error while loading state for instance 0x0 of device 'ram'
qemu-system-x86_64: load of migration failed: Invalid argument
We'll refactor the code next, to make sure we get rid of this implicit
behavior for "etc/acpi/rsdp" as well and to make the code easier to
grasp.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-2-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Implement _DSM according to:
PCI Firmware Specification 3.1
4.6.7. DSM for Naming a PCI or PCI Express Device Under
Operating Systems
and wire it up to cold and hot-plugged PCI devices.
Feature depends on ACPI hotplug being enabled (as that provides
PCI devices descriptions in ACPI and MMIO registers that are
reused to fetch acpi-index).
acpi-index should work for
- cold plugged NICs:
$QEMU -device e1000,acpi-index=100
=> 'eno100'
- hot-plugged
(monitor) device_add e1000,acpi-index=200,id=remove_me
=> 'eno200'
- re-plugged
(monitor) device_del remove_me
(monitor) device_add e1000,acpi-index=1
=> 'eno1'
Windows also sees index under "PCI Label Id" field in properties
dialog but otherwise it doesn't seem to have any effect.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210315180102.3008391-6-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will be used by follow up patches
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210315180102.3008391-5-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In x86/ACPI world, linux distros are using predictable
network interface naming since systemd v197. Which on
QEMU based VMs results into path based naming scheme,
that names network interfaces based on PCI topology.
With itm on has to plug NIC in exactly the same bus/slot,
which was used when disk image was first provisioned/configured
or one risks to loose network configuration due to NIC being
renamed to actually used topology.
That also restricts freedom to reshape PCI configuration of
VM without need to reconfigure used guest image.
systemd also offers "onboard" naming scheme which is
preferred over PCI slot/topology one, provided that
firmware implements:
"
PCI Firmware Specification 3.1
4.6.7. DSM for Naming a PCI or PCI Express Device Under
Operating Systems
"
that allows to assign user defined index to PCI device,
which systemd will use to name NIC. For example, using
-device e1000,acpi-index=100
guest will rename NIC to 'eno100', where 'eno' is default
prefix for "onboard" naming scheme. This doesn't require
any advance configuration on guest side to com in effect
at 'onboard' scheme takes priority over path based naming.
Hope is that 'acpi-index' it will be easier to consume by
management layer, compared to forcing specific PCI topology
and/or having several disk image templates for different
topologies and will help to simplify process of spawning
VM from the same template without need to reconfigure
guest NIC.
This patch adds, 'acpi-index'* property and wires up
a 32bit register on top of pci hotplug register block
to pass index value to AML code at runtime.
Following patch will add corresponding _DSM code and
wire it up to PCI devices described in ACPI.
*) name comes from linux kernel terminology
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210315180102.3008391-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This adds a flag in NetClientState, so that a net client can tell
its peer that the packets do not need to be padded to the minimum
size of an Ethernet frame (60 bytes) before sending to it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add a helper to pad a short Ethernet frame to the minimum required
length, which can be used by backends' code.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This policy rejects deprecated input, and thus permits "testing the
future". Implement it for QMP command arguments: reject commands with
deprecated ones. Example: when QEMU is run with -compat
deprecated-input=reject, then
{"execute": "eject", "arguments": {"device": "cd"}}
fails like this
{"error": {"class": "GenericError", "desc": "Deprecated parameter 'device' disabled by policy"}}
When the deprecated parameter is removed, the error will change to
{"error": {"class": "GenericError", "desc": "Parameter 'device' is unexpected"}}
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-11-armbru@redhat.com>
This policy rejects deprecated input, and thus permits "testing the
future". Implement it for QMP commands: make deprecated ones fail.
Example: when QEMU is run with -compat deprecated-input=reject, then
{"execute": "query-cpus"}
fails like this
{"error": {"class": "CommandNotFound", "desc": "Deprecated command query-cpus disabled by policy"}}
When the deprecated command is removed, the error will change to
{"error": {"class": "CommandNotFound", "desc": "The command query-cpus has not been found"}}
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-10-armbru@redhat.com>
This policy suppresses deprecated bits in output, and thus permits
"testing the future". Implement it for QMP command results. Example:
when QEMU is run with -compat deprecated-output=hide, then
{"execute": "query-cpus-fast"}
yields
{"return": [{"thread-id": 9805, "props": {"core-id": 0, "thread-id": 0, "socket-id": 0}, "qom-path": "/machine/unattached/device[0]", "cpu-index": 0, "target": "x86_64"}]}
instead of
{"return": [{"arch": "x86", "thread-id": 22436, "props": {"core-id": 0, "thread-id": 0, "socket-id": 0}, "qom-path": "/machine/unattached/device[0]", "cpu-index": 0, "target": "x86_64"}]}
Note the suppression of deprecated member "arch".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-4-armbru@redhat.com>
New option -compat lets you configure what to do when deprecated
interfaces get used. This is intended for testing users of the
management interfaces. It is experimental.
-compat deprecated-input=<input-policy> configures what to do when
deprecated input is received. Input policy can be "accept" (accept
silently), or "reject" (reject the request with an error).
-compat deprecated-output=<out-policy> configures what to do when
deprecated output is sent. Output policy can be "accept" (pass on
unchanged), or "hide" (filter out the deprecated parts).
Default is "accept". Policies other than "accept" are implemented
later in this series.
For now, -compat covers only syntactic aspects of QMP, i.e. stuff
tagged with feature 'deprecated'. We may want to extend it to cover
semantic aspects, CLI, and experimental features.
Note that there is no good way for management application to detect
presence of -compat: it's not visible output of query-qmp-schema or
query-command-line-options. Tolerable, because it's meant for
testing. If running with -compat fails, skip the test.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20210318155519.1224118-3-armbru@redhat.com>
Almost all QOM type names consist only of letters, digits, '-', '_',
and '.'. Just two contain ':': "qemu:memory-region" and
"qemu:iommu-memory-region". Neither can be plugged with -object.
Rename them to "memory-region" and "iommu-memory-region".
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210304140229.575481-3-armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Several QOM type names contain ',':
ARM,bitband-memory
etraxfs,pic
etraxfs,serial
etraxfs,timer
fsl,imx25
fsl,imx31
fsl,imx6
fsl,imx6ul
fsl,imx7
grlib,ahbpnp
grlib,apbpnp
grlib,apbuart
grlib,gptimer
grlib,irqmp
qemu,register
SUNW,bpp
SUNW,CS4231
SUNW,DBRI
SUNW,DBRI.prom
SUNW,fdtwo
SUNW,sx
SUNW,tcx
xilinx,zynq_slcr
xlnx,zynqmp
xlnx,zynqmp-pmu-soc
xlnx,zynq-xadc
These are all device types. They can't be plugged with -device /
device_add, except for xlnx,zynqmp-pmu-soc, and I doubt that one
actually works.
They *can* be used with -device / device_add to request help.
Usability is poor, though: you have to double the comma, like this:
$ qemu-system-x86_64 -device SUNW,,fdtwo,help
Trap for the unwary. The fact that this was broken in
device-introspect-test for more than six years until commit e27bd49876
fixed it demonstrates that "the unwary" includes seasoned developers.
One QOM type name contains ' ': "ICH9 SMB". Because having to
remember just one way to quote would be too easy.
Rename the "SUNW,FOO types to "sun-FOO". Summarily replace ',' and '
' by '-' in the other type names.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210304140229.575481-2-armbru@redhat.com>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Drop the crap deprecated in commit a1b40bda08 "blockdev: Deprecate
-drive with bogus interface type" (v5.1.0).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Message-id: 20210309161214.1402527-5-armbru@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Emulators are currently using OptsVisitor (via user_creatable_add_opts)
to parse the -object command line option. This has one extra feature,
compared to keyval, which is automatic conversion of integers to lists
as well as support for lists as repeated options:
-object memory-backend-ram,id=pc.ram,size=1048576000,host-nodes=0,policy=bind
So we cannot replace OptsVisitor with keyval right now. Still, this
patch moves the user_creatable_add_opts logic to vl.c since it is
not needed anywhere else, and makes it go through user_creatable_add_qapi.
In order to minimize code changes, the predicate still takes a string.
This can be changed later to use the ObjectType QAPI enum directly.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210312173547.1283477-3-pbonzini@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The system emulator has a more complicated way of handling command line
options in that it reorders options before it processes them. This means
that parsing object options and creating the object happen at two
different points. Split the parsing part into a separate function that
can be reused by the system emulator command line.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This is a version of user_creatable_process_cmdline() with an Error
parameter that never calls exit() and is therefore usable in HMP.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
The implementation for --object can be shared between
qemu-storage-daemon and other binaries, so move it into a function in
qom/object_interfaces.c that is accessible from everywhere.
This also requires moving the implementation of qmp_object_add() into a
new user_creatable_add_qapi(), because qom/qom-qmp-cmds.c is not linked
for tools.
user_creatable_print_help_from_qdict() can become static now.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This function is now unused and can be removed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
This converts object-add from 'gen': false to the ObjectOptions QAPI
type. As an immediate benefit, clients can now use QAPI schema
introspection for user creatable QOM objects.
It is also the first step towards making the QAPI schema the only
external interface for the creation of user creatable objects. Once all
other places (HMP and command lines of the system emulator and all
tools) go through QAPI, too, some object implementations can be
simplified because some checks (e.g. that mandatory options are set) are
already performed by QAPI, and in another step, QOM boilerplate code
could be generated from the schema.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Peter Krempa <pkrempa@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
* fixes for Coverity CID 1450756, 1450757 and 1450758 (me)
* fix for a bug in zone management receive (me)
* metadata and end-to-end data protection support (me & Gollu Appalanaidu)
* verify support (Gollu Appalanaidu)
* multiple lba formats and format nvm support (Minwoo Im)
and a couple of misc refactorings from me.
v2:
- remove an unintended submodule update. Argh.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEUigzqnXi3OaiR2bATeGvMW1PDekFAmBTP0wACgkQTeGvMW1P
DelZvAf+Ijw77YLz2t0P97CiwoOAG4FADwo61WQJo2AHyS3JMYPVdgNUXF7UGt/S
cNhU1JjdEylgZPKi5t9o/qgy7+vtSL0KKqoXIS0z9ZWZkdFsgObNetGULhaqXgaX
4KcAt7PyJS/33uFqYGSVZxJTO4GtCy34hGw6XrVs388tQD1S+eI+oS5EYBN57rl9
MrV5Z72iMCBx8Y074u81SD/u7n34b5WWbUOJADVI1rAKhilDhnkAhBQ/gK/UBodB
trUUQY/KU+eCnXEqfBeMD6fL75UOAFOjnm7Kfk/Q/g3di3H2fu0RGLrJuSS1dG0n
zmwgE7pQ1jT1UcB3QwAJLR3tGtd6sA==
=HwqP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/nvme/tags/nvme-next-pull-request' into staging
emulated nvme updates and fixes
* fixes for Coverity CID 1450756, 1450757 and 1450758 (me)
* fix for a bug in zone management receive (me)
* metadata and end-to-end data protection support (me & Gollu Appalanaidu)
* verify support (Gollu Appalanaidu)
* multiple lba formats and format nvm support (Minwoo Im)
and a couple of misc refactorings from me.
v2:
- remove an unintended submodule update. Argh.
# gpg: Signature made Thu 18 Mar 2021 11:53:48 GMT
# gpg: using RSA key 522833AA75E2DCE6A24766C04DE1AF316D4F0DE9
# gpg: Good signature from "Klaus Jensen <its@irrelevant.dk>" [unknown]
# gpg: aka "Klaus Jensen <k.jensen@samsung.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: DDCA 4D9C 9EF9 31CC 3468 4272 63D5 6FC5 E55D A838
# Subkey fingerprint: 5228 33AA 75E2 DCE6 A247 66C0 4DE1 AF31 6D4F 0DE9
* remotes/nvme/tags/nvme-next-pull-request:
hw/block/nvme: add support for the format nvm command
hw/block/nvme: pull lba format initialization
hw/block/nvme: prefer runtime helpers instead of device parameters
hw/block/nvme: support multiple lba formats
hw/block/nvme: add non-mdts command size limit for verify
hw/block/nvme: add verify command
hw/block/nvme: end-to-end data protection
hw/block/nvme: add metadata support
hw/block/nvme: fix zone management receive reporting too many zones
hw/block/nvme: assert namespaces array indices
hw/block/nvme: fix potential overflow
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Format NVM admin command can make a namespace or namespaces to be
with different LBA size and metadata size with protection information
types.
This patch introduces Format NVM command with LBA format, Metadata, and
Protection Information for the device. The secure erase operation things
and support for formatting zoned namespaces are yet to be added.
The parameter checks inside of this patch has been referred from
Keith's old branch.
Signed-off-by: Minwoo Im <minwoo.im@samsung.com>
[anaidu.gollu: rebased on e2e]
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
[k.jensen: rebased for reworked aio tracking]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for namespaces formatted with protection information. The
type of end-to-end data protection (i.e. Type 1, Type 2 or Type 3) is
selected with the `pi` nvme-ns device parameter. If the number of
metadata bytes is larger than 8, the `pil` nvme-ns device parameter may
be used to control the location of the 8-byte DIF tuple. The default
`pil` value of '0', causes the DIF tuple to be transferred as the last
8 bytes of the metadata. Set to 1 to store this in the first eight bytes
instead.
Co-authored-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
* fix guest-get-vcpus reporting after vcpu unplug
* coding style fix-ups
* report a reason for disabled commands
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEzqzJ4VU066u4LT+gM1PJzvEItYQFAmBRc6kACgkQM1PJzvEI
tYRTyAf/RAL9jEf6zFtztqpTKOUoptnBjtF2bb4A9WQ72/9sFzoufYoCSKeSEbuv
9vEK1DW5JkgR5DETsk3qWCr4TK2wNf7rZde87iy5pOxPQqaUNwx5HFZqZnBMv3wl
SIWRoa5fPucUOZQkYgjellRNlGVm0QJ1+hqmj+0Dwbw04KBti0Hbyl7YS23BskD0
wafPensotjEswtbxG20yCW4WerI5XVnrPYURD8+lBMYYOxLgsIc+fSUZ+Ak+4gO+
i3rgK7RamzoWJ/L9am8v7uImH1k74tO3g6iws79exT8wWK2o4/vqQYF2TMtTrUvq
9ZBA1ehd6L0bDDRXFNsBOc27jADRIw==
=d1L/
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mdroth/tags/qga-pull-2021-03-16-tag' into staging
qemu-ga patch queue for soft-freeze
* fix guest-get-vcpus reporting after vcpu unplug
* coding style fix-ups
* report a reason for disabled commands
# gpg: Signature made Wed 17 Mar 2021 03:12:41 GMT
# gpg: using RSA key CEACC9E15534EBABB82D3FA03353C9CEF108B584
# gpg: Good signature from "Michael Roth <flukshun@gmail.com>" [full]
# gpg: aka "Michael Roth <mdroth@utexas.edu>" [full]
# gpg: aka "Michael Roth <mdroth@linux.vnet.ibm.com>" [full]
# Primary key fingerprint: CEAC C9E1 5534 EBAB B82D 3FA0 3353 C9CE F108 B584
* remotes/mdroth/tags/qga-pull-2021-03-16-tag:
qga: return a more explicit error on why a command is disabled
qga: Switch and case should be at the same indent
qga: Open brace '{' following struct go on the same
qga: Delete redundant spaces
qga: Add spaces around operator
qga: Correct loop count in qmp_guest_get_vcpus()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The same information is available via the 'recording' and 'busy' fields.
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
The generic 'migrate_set_parameters' command handle all types of param.
Only the QMP commands were documented in the deprecations page, but the
rationale for deprecating applies equally to HMP, and the replacements
exist. Furthermore the HMP commands are just shims to the QMP commands,
so removing the latter breaks the former unless they get re-implemented.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
- get rid of legacy_s390_alloc() and phys_mem_set_alloc()
- tcg: implement the MVPG condition-code-option bit
- fix g_autofree variable handing in the pci vfio code
- use official z15 names in the cpu model definitions
-----BEGIN PGP SIGNATURE-----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=8eNE
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck-gitlab/tags/s390x-20210316' into staging
s390x updates:
- get rid of legacy_s390_alloc() and phys_mem_set_alloc()
- tcg: implement the MVPG condition-code-option bit
- fix g_autofree variable handing in the pci vfio code
- use official z15 names in the cpu model definitions
# gpg: Signature made Tue 16 Mar 2021 10:04:21 GMT
# gpg: using RSA key C3D0D66DC3624FF6A8C018CEDECF6B93C6F02FAF
# gpg: issuer "cohuck@redhat.com"
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>" [unknown]
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cohuck@kernel.org>" [unknown]
# gpg: aka "Cornelia Huck <cohuck@redhat.com>" [unknown]
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck-gitlab/tags/s390x-20210316:
s390x/pci: Add missing initialization for g_autofree variables
target/s390x: Store r1/r2 for page-translation exceptions during MVPG
target/s390x: Implement the MVPG condition-code-option bit
s390x/cpu_model: use official name for 8562
exec: Get rid of phys_mem_set_alloc()
s390x/kvm: Get rid of legacy_s390_alloc()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Actually print arguments as opposed to simply the opcodes
and, uselessly, the argument counts. Reuse all of the helpers
developed as part of the interpreter.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Getting the comment consistence with the function name
Signed-off-by: Yonggang Luo <luoyonggang@gmail.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20201013002806.1447-3-luoyonggang@gmail.com>
Message-Id: <20210312172821.31647-15-alex.bennee@linaro.org>
Remove the extraneous @cb parameter and document the non-atomic nature
of the INLINE_ADD_U64 operation.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210312172821.31647-11-alex.bennee@linaro.org>
Also add a note to explain currently they are unused.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210312172821.31647-9-alex.bennee@linaro.org>
kernel-doc doesn't like multiple Note sections. Also add an explicit
Return.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210312172821.31647-6-alex.bennee@linaro.org>
It seems kernel-doc struggles a bit with typedef structs but with
enough encouragement we can get something out of it.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210312172821.31647-5-alex.bennee@linaro.org>
This allows plugins to query for full virtual-to-physical address
translation for a given `qemu_plugin_hwaddr` and stops exposing the
offset within the device itself. As this change breaks the API,
QEMU_PLUGIN_VERSION is incremented.
Signed-off-by: Aaron Lindsay <aaron@os.amperecomputing.com>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210309202802.211756-1-aaron@os.amperecomputing.com>
Message-Id: <20210312172821.31647-3-alex.bennee@linaro.org>
qmp_disable_command() now takes an optional error string to return a
more explicit error message.
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1928806
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
*fix up 80+ char line
Signed-off-by: Michael Roth <michael.roth@amd.com>
According to the "Guide To The Macintosh Family Hardware", the 60Hz VIA1 timer
on newer Macs such as the Quadra only exists for compatibility with old software
and is no longer synced to the VBL interval.
Rename the VBL timer to 60Hz timer to emphasise this and to prevent confusion
when the real VBL interrupt (now handled as a NuBus slot interrupt) is added in
future.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210311100505.22596-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since 5f8e93c3e2 ("util/qemu-timer: Make timer_free() imply timer_del()", 2021-01-08)
it is not possible anymore to pass a NULL pointer to timer_free(). Previously
it would do nothing as it would simply pass NULL down to g_free().
Rectify this, which also fixes "-chardev braille" when there is no device.
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
For testing, it can be useful to simulate an enormous amount of memory
(e.g. 2^64 RAM). This adds an MMIO device that acts as sparse memory.
When something writes a nonzero value to a sparse-mem address, we
allocate a block of memory. For now, since the only user of this device
is the fuzzer, we do not track and free zeroed blocks. The device has a
very low priority (so it can be mapped beneath actual RAM, and virtual
device MMIO regions).
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJgTx3xAAoJEO8Ells5jWIRtBsH/2MCZJKg4wTB4a7qAYTyuUmZ
qz1Z8d5J1JSyAQiiUN+lFo1Gtpuqpyci4CT5gHz4ru2UV9DBJy9cDGApug66QOM8
stbztOeRIfcLLeWCepQIoSESteesiyMM6h1Q/x9lF87eN7JXrNmACp+jAhTDHq1B
QFwYVGLwkaFkvE9G04yzCZSo37+j2nPAauIuoJs1B01on6a5hj7Isdumn2P1TGyz
6nJTkyWLsPzEM+lGMfxYdMpnELibJ935CX78DGcnZK9qhI7rw4xLFuZtyTW+N+B8
h5OX9aCqrIF5AX7xNTvQeQwclnEe+KzBUwkbDJARViEUDOoKfb6t1Yv+3Xghdqo=
=57xH
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 15 Mar 2021 08:42:25 GMT
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net: Do not fill legacy info_str for backends
hmp: Use QAPI NetdevInfo in hmp_info_network
net: Move NetClientState.info_str to dynamic allocations
tests: Add tests for query-netdev command
qapi: net: Add query-netdev command
pvrdma: wean code off pvrdma_ring.h kernel header
lan9118: switch to use qemu_receive_packet() for loopback
cadence_gem: switch to use qemu_receive_packet() for loopback
pcnet: switch to use qemu_receive_packet() for loopback
rtl8139: switch to use qemu_receive_packet() for loopback
tx_pkt: switch to use qemu_receive_packet_iov() for loopback
sungem: switch to use qemu_receive_packet() for loopback
msf2-mac: switch to use qemu_receive_packet() for loopback
dp8393x: switch to use qemu_receive_packet() for loopback packet
e1000: switch to use qemu_receive_packet() for loopback
net: introduce qemu_receive_packet()
e1000: fail early for evil descriptor
net: validate that ids are well formed
net: Fix build error when DEBUG_NET is on
virtio-net: calculating proper msix vectors on init
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/core/machine.c
The machine is based on Goldfish interfaces defined by Google
for Android simulator. It uses Goldfish-rtc (timer and RTC),
Goldfish-pic (PIC) and Goldfish-tty (for serial port and early tty).
The machine is created with 128 virtio-mmio bus, and they can
be used to use serial console, GPU, disk, NIC, HID, ...
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-6-laurent@vivier.eu>
Add a system controller for the m68k-virt machine.
This controller allows the kernel to power off or reset the machine.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-5-laurent@vivier.eu>
A (generic) copy of the GLUE device we already have for q800 to use with
the m68k-virt machine.
The q800 one would disappear in the future as q800 uses actually the djMEMC
controller.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-4-laurent@vivier.eu>
Implement the goldfish pic device as defined in
https://android.googlesource.com/platform/external/qemu/+/master/docs/GOLDFISH-VIRTUAL-HARDWARE.TXT
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210312214145.2936082-3-laurent@vivier.eu>
In preparation for splitting the usb-storage.c file move
declarations to the new usb/msd.h header file.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20210312090425.772900-2-kraxel@redhat.com>
No device needs them anymore and in fact they're undocumented.
Remove the code. The only change in behavior is that "-usbdevice
braille:hello" now reports an error, which is a bugfix.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210310173323.1422754-2-thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This property was only required for the pc-1.0 and earlier machine
types. Since these have been removed now, we can delete the property
as well.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210302120152.118042-1-thuth@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
As the last user is gone, we can get rid of phys_mem_set_alloc() and
simplify.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Halil Pasic <pasic@linux.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Thomas Huth <thuth@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20210303130916.22553-3-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Report the configured granularity for discard operation to the
guest. If this is not set use the block size.
Since until now we have ignored the configured discard granularity
and always reported the block size, let's add
'report-discard-granularity' property and disable it for older
machine types to avoid migration issues.
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20210225001239.47046-1-akihiko.odaki@gmail.com>
Replace usage of legacy field info_str of NetClientState for backend
network devices with QAPI NetdevInfo stored_config that already used
in QMP query-netdev.
This change increases the detail of the "info network" output and takes
a more general approach to composing the output.
NIC and hubports still use legacy info_str field.
Signed-off-by: Alexey Kirillov <lekiravi@yandex-team.ru>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The info_str field of the NetClientState structure is static and has a size
of 256 bytes. This amount is often unclaimed, and the field itself is used
exclusively for HMP "info network".
The patch translates info_str to dynamic memory allocation.
This action is also allows us to painlessly discard usage of this field
for backend devices.
Signed-off-by: Alexey Kirillov <lekiravi@yandex-team.ru>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The query-netdev command is used to get the configuration of the current
network device backends (netdevs).
This is the QMP analog of the HMP command "info network" but only for
netdevs (i.e. excluding NIC and hubports).
The query-netdev command returns an array of objects of the NetdevInfo
type, which are an extension of Netdev type. It means that response can
be used for netdev-add after small modification. This can be useful for
recreate the same netdev configuration.
Information about the network device is filled in when it is created or
modified and is available through the NetClientState->stored_config.
Signed-off-by: Alexey Kirillov <lekiravi@yandex-team.ru>
Acked-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
The pvrdma code relies on the pvrdma_ring.h kernel header for some
basic ring buffer handling. The content of that header isn't very
exciting, but contains some (q)atomic_*() invocations that (a)
cause manual massaging when doing a headers update, and (b) are
an indication that we probably should not be importing that header
at all.
Let's reimplement the ring buffer handling directly in the pvrdma
code instead. This arguably also improves readability of the code.
Importing the header can now be dropped.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Yuval Shaia <yuval.shaia.ml@gmail.com>
Tested-by: Yuval Shaia <yuval.shaia.ml@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Some NIC supports loopback mode and this is done by calling
nc->info->receive() directly which in fact suppresses the effort of
reentrancy check that is done in qemu_net_queue_send().
Unfortunately we can't use qemu_net_queue_send() here since for
loopback there's no sender as peer, so this patch introduce a
qemu_receive_packet() which is used for implementing loopback mode
for a NIC with this check.
NIC that supports loopback mode will be converted to this helper.
This is intended to address CVE-2021-3416.
Cc: Prasad J Pandit <ppandit@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Add the yellow "lime" LED.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Michael Rolnik <mrolnik@gmail.com>
Message-Id: <20210313165445.2113938-2-f4bug@amsat.org>
This patch adds fan_splitters (split IRQs) in NPCM7XX boards. Each fan
splitter corresponds to 1 PWM output and can connect to multiple fan
inputs (MFT devices).
In NPCM7XX boards(NPCM750 EVB and Quanta GSJ boards), we initializes
these splitters and connect them to their corresponding modules
according their specific device trees.
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210311180855.149764-5-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements Multi Function Timer (MFT) module for NPCM7XX.
This module is mainly used to configure PWM fans. It has just enough
functionality to make the PWM fan kernel module work.
The module takes two input, the max_rpm of a fan (modifiable via QMP)
and duty cycle (a GPIO from the PWM module.) The actual measured RPM
is equal to max_rpm * duty_cycle / NPCM7XX_PWM_MAX_DUTY. The RPM is
measured as a counter compared to a prescaled input clock. The kernel
driver reads this counter and report to user space.
Refs:
https://github.com/torvalds/linux/blob/master/drivers/hwmon/npcm750-pwm-fan.c
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Message-id: 20210311180855.149764-3-wuhaotsh@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds GPIOs in NPCM7xx PWM module for its duty values.
The purpose of this is to connect it to the MFT module to provide
an input for measuring a PWM fan's RPM. Each PWM module has
NPCM7XX_PWM_PER_MODULE of GPIOs, each one corresponds to
one PWM instance and can connect to multiple fan instances in MFT.
Reviewed-by: Doug Evans <dje@google.com>
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20210311180855.149764-2-wuhaotsh@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Prior to commit f2ce39b4f0 a MachineClass kvm_type method
only needed to be registered to ensure it would be executed.
With commit f2ce39b4f0 a kvm-type machine property must also
be specified. hw/arm/virt relies on the kvm_type method to pass
its selected IPA limit to KVM, but this is not exposed as a
machine property. Restore the previous functionality of invoking
kvm_type when it's present.
Fixes: f2ce39b4f0 ("vl: make qemu_get_machine_opts static")
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210310135218.255205-2-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently get_naturally_aligned_size() is used by the intel iommu
to compute the maximum invalidation range based on @size which is
a power of 2 while being aligned with the @start address and less
than the maximum range defined by @gaw.
This helper is also useful for other iommu devices (virtio-iommu,
SMMUv3) to make sure IOMMU UNMAP notifiers only are called with
power of 2 range sizes.
Let's move this latter into dma-helpers.c and rename it into
dma_aligned_pow2_mask(). Also rewrite the helper so that it
accomodates UINT64_MAX values for the size mask and max mask.
It now returns a mask instead of a size. Change the caller.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 20210309102742.30442-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the support for the Versal Accelerator RAMs (XRAMs).
Reviewed-by: Luc Michel <luc@lmichel.fr>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210308224637.2949533-3-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the Xilinx Versal Accelerator RAM (XRAM).
This is mainly a stub to make firmware happy. The size of
the RAMs can be probed. The interrupt mask logic is
modelled but none of the interrups will ever be raised
unless injected.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210308224637.2949533-2-edgar.iglesias@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Next batch of patches for the ppc target and machine types. Includes:
* Several cleanups for sm501 from Peter Maydell
* An update to the SLOF guest firmware
* Improved handling of hotplug failures in spapr, associated cleanups
to the hotplug handling code
* Several etsec fixes and cleanups from Bin Meng
* Assorted other fixes and cleanups
-----BEGIN PGP SIGNATURE-----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=/uyx
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dg-gitlab/tags/ppc-for-6.0-20210310' into staging
ppc patch queue for 2021-03-10
Next batch of patches for the ppc target and machine types. Includes:
* Several cleanups for sm501 from Peter Maydell
* An update to the SLOF guest firmware
* Improved handling of hotplug failures in spapr, associated cleanups
to the hotplug handling code
* Several etsec fixes and cleanups from Bin Meng
* Assorted other fixes and cleanups
# gpg: Signature made Wed 10 Mar 2021 04:08:53 GMT
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.0-20210310:
spapr.c: send QAPI event when memory hotunplug fails
spapr.c: remove duplicated assert in spapr_memory_unplug_request()
target/ppc: fix icount support on Book-e vms accessing SPRs
qemu_timer.c: add timer_deadline_ms() helper
spapr_pci.c: add 'unplug already in progress' message for PCI unplug
spapr.c: add 'unplug already in progress' message for PHB unplug
hw/ppc: e500: Add missing <ranges> in the eTSEC node
hw/net: fsl_etsec: Fix build error when HEX_DUMP is on
spapr_drc.c: use DRC reconfiguration to cleanup DIMM unplug state
spapr_drc.c: add hotunplug timeout for CPUs
spapr_drc.c: introduce unplug_timeout_timer
target/ppc: Fix bcdsub. emulation when result overflows
docs/system: Extend PPC section
spapr: rename spapr_drc_detach() to spapr_drc_unplug_request()
spapr_drc.c: use spapr_drc_release() in isolate_physical/set_unusable
pseries: Update SLOF firmware image
spapr_drc.c: do not call spapr_drc_detach() in drc_isolate_logical()
hw/display/sm501: Inline template header into C file
hw/display/sm501: Expand out macros in template header
hw/display/sm501: Remove dead code for non-32-bit RGB surfaces
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmBI50MACgkQ+9DbCVqe
KkSyKggAhPZW+7sReVEsFdnVfwuo3evW7auoW44mghNbikTnm3RfoahYTrek8lGZ
AEo2gFMbzENW0j88e0OvSYYtwkVz3sD68bygfXerti6sQwWlwkf42I/suWjJNLph
oVKGEEdJess9+zR13Cu6RAq5RaTwzDPGPjUwTbeJPpAps4+UZV3hsxhaxs8keII6
GBa/idnh0qEApP2NDLKiSASrYZM7xGvljE7zO4qhchd6iSH/o5rCtkoB2tRCcXGo
+KF8LyBsUNf7GiWp0yYZMZUQ3Pqskqma8N3d2A4UlS1kXvxeX/FiORkG/Ne8bH1Z
VZ1Z/xbyXGlVkiP1bcoYSc6XWHNDTw==
=R9zQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2' into staging
Testing, guest-loader and other misc tweaks
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
# gpg: Signature made Wed 10 Mar 2021 15:35:31 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2:
semihosting: Move hw/semihosting/ -> semihosting/
semihosting: Move include/hw/semihosting/ -> include/semihosting/
tests/avocado: add boot_xen tests
docs: add some documentation for the guest-loader
docs: move generic-loader documentation into the main manual
hw/core: implement a guest-loader to support static hypervisor guests
device_tree: add qemu_fdt_setprop_string_array helper
hw/riscv: migrate fdt field to generic MachineState
hw/board: promote fdt from ARM VirtMachineState to MachineState
.editorconfig: update the automatic mode setting for Emacs
tests/docker: Use --arch-only when building Debian cross image
gitlab-ci.yml: Add jobs to test CFI flags
gitlab-ci.yml: Allow custom # of parallel linkers
tests/docker: add a test-tcg for building then running check-tcg
docs/system: add a gentle prompt for the complexity to come
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- Add Vladimir as NBD co-maintainer
- Fix reporting of holes in NBD_CMD_BLOCK_STATUS
- Improve command-line parsing accuracy of large numbers (anything going
through qemu_strtosz), including the deprecation of hex+suffix
- Improve some error reporting in the block layer
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEccLMIrHEYCkn0vOqp6FrSiUnQ2oFAmBHlmIACgkQp6FrSiUn
Q2q2cQgAqJWNb4J/ShjvzocDDPzJ0iBitFbg0huFPfbt4DScubEZo5wBJG7vOhOW
hIHrWCRzGvRgsn0tcSfrgFaegmHKrLgjkibM7ou8ni9NC1kUBd3R/3FBNIMxhYf7
Q8Kfspl0LRfMJDKF9jdCnQ4Gxcd6h2OIYZqiWVg8V4Tc8WdCpIVOah7e7wjuW8bT
vgZvfboUWm5AmIF9j/MxuMn+HFZ4ArSuFVL80ZaXlD00vRra7u3HZ8pUfcOlOujg
7HeouM1E5j3NNE6aZSN++x/EQ3sg0zmirbWUCcgAyRfdRkAmB15uh2PUzPxEIJKH
UHUIW5LvNtz2+yzOAz2yK29OE523Yg==
=blE1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ericb/tags/pull-nbd-2021-03-09' into staging
nbd patches for 2021-03-09
- Add Vladimir as NBD co-maintainer
- Fix reporting of holes in NBD_CMD_BLOCK_STATUS
- Improve command-line parsing accuracy of large numbers (anything going
through qemu_strtosz), including the deprecation of hex+suffix
- Improve some error reporting in the block layer
# gpg: Signature made Tue 09 Mar 2021 15:38:10 GMT
# gpg: using RSA key 71C2CC22B1C4602927D2F3AAA7A16B4A2527436A
# gpg: Good signature from "Eric Blake <eblake@redhat.com>" [full]
# gpg: aka "Eric Blake (Free Software Programmer) <ebb9@byu.net>" [full]
# gpg: aka "[jpeg image of size 6874]" [full]
# Primary key fingerprint: 71C2 CC22 B1C4 6029 27D2 F3AA A7A1 6B4A 2527 436A
* remotes/ericb/tags/pull-nbd-2021-03-09:
block/qcow2: refactor qcow2_update_options_prepare error paths
block/qed: bdrv_qed_do_open: deal with errp
block/qcow2: simplify qcow2_co_invalidate_cache()
block/qcow2: read_cache_sizes: return status value
block/qcow2-bitmap: return status from qcow2_store_persistent_dirty_bitmaps
block/qcow2-bitmap: improve qcow2_load_dirty_bitmaps() interface
block/qcow2: qcow2_get_specific_info(): drop error propagation
blockjob: return status from block_job_set_speed()
block/mirror: drop extra error propagation in commit_active_start()
block: drop extra error propagation for bdrv_set_backing_hd
blockdev: fix drive_backup_prepare() missed error
block: check return value of bdrv_open_child and drop error propagation
utils: Deprecate hex-with-suffix sizes
utils: Improve qemu_strtosz() to have 64 bits of precision
utils: Enhance testsuite for do_strtosz()
nbd: server: Report holes for raw images
MAINTAINERS: add Vladimir as co-maintainer of NBD
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* New model for the Aspeed LPC controller
* Misc cleanups
-----BEGIN PGP SIGNATURE-----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=SWwQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20210309' into staging
Aspeed patches :
* New model for the Aspeed LPC controller
* Misc cleanups
# gpg: Signature made Tue 09 Mar 2021 11:54:25 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20210309:
hw/misc: Model KCS devices in the Aspeed LPC controller
hw/misc: Add a basic Aspeed LPC controller model
hw/arm: ast2600: Correct the iBT interrupt ID
hw/arm: ast2600: Set AST2600_MAX_IRQ to value from datasheet
hw/arm: ast2600: Force a multiple of 32 of IRQs for the GIC
hw/arm/aspeed: Fix location of firmware images in documentation
arm/ast2600: Fix SMP booting with -kernel
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We want to move the semihosting code out of hw/ in the next patch.
This patch contains the mechanical steps, created using:
$ git mv include/hw/semihosting/ include/
$ sed -i s,hw/semihosting,semihosting, $(git grep -l hw/semihosting)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210226131356.3964782-2-f4bug@amsat.org>
Message-Id: <20210305135451.15427-2-alex.bennee@linaro.org>
A string array in device tree is simply a series of \0 terminated
strings next to each other. As libfdt doesn't support that directly
we need to build it ourselves.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210303173642.3805-4-alex.bennee@linaro.org>
This is a mechanical change to make the fdt available through
MachineState.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-3-alex.bennee@linaro.org>
The use of FDT's is quite common across our various platforms. To
allow the guest loader to tweak it we need to make it available in
the generic state. This creates the field and migrates the initial
user to use the generic field. Other boards will be updated in later
patches.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-2-alex.bennee@linaro.org>
* Add new mps3-an547 board
* target/arm: Restrict v7A TCG cpus to TCG accel
* Implement a Xilinx CSU DMA model
* hw/timer/renesas_tmr: Fix use of uninitialized data in read_tcnt()
-----BEGIN PGP SIGNATURE-----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=Qu2a
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210310' into staging
target-arm queue:
* Add new mps3-an547 board
* target/arm: Restrict v7A TCG cpus to TCG accel
* Implement a Xilinx CSU DMA model
* hw/timer/renesas_tmr: Fix use of uninitialized data in read_tcnt()
# gpg: Signature made Wed 10 Mar 2021 13:56:20 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210310: (54 commits)
hw/timer/renesas_tmr: Fix use of uninitialized data in read_tcnt()
hw/timer/renesas_tmr: Prefix constants for CSS values with CSS_
hw/ssi: xilinx_spips: Remove DMA related dead codes from zynqmp_spips
hw/ssi: xilinx_spips: Clean up coding convention issues
hw/arm: xlnx-zynqmp: Connect a Xilinx CSU DMA module for QSPI
hw/arm: xlnx-zynqmp: Clean up coding convention issues
hw/dma: Implement a Xilinx CSU DMA model
target/arm: Restrict v7A TCG cpus to TCG accel
tests/qtest/sse-timer-test: Test counter scaling changes
tests/qtest/sse-timer-test: Test the system timer
tests/qtest/sse-timer-test: Add simple test of the SSE counter
docs/system/arm/mps2.rst: Document the new mps3-an547 board
hw/arm/mps2-tz: Add new mps3-an547 board
hw/arm/mps2-tz: Make initsvtor0 setting board-specific
hw/arm/mps2-tz: Support running APB peripherals on different clock
hw/misc/mps2-scc: Implement changes for AN547
hw/misc/mps2-fpgaio: Support AN547 DBGCTRL register
hw/misc/mps2-fpgaio: Fold counters subsection into main vmstate
hw/arm/mps2-tz: Make UART overflow IRQ board-specific
hw/arm/armsse: Add SSE-300 support
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that the Xilinx CSU DMA model is implemented, the existing
DMA related dead codes in the ZynqMP QSPI are useless and should
be removed. The maximum register number is also updated to only
include the QSPI registers.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-6-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a Xilinx CSU DMA module to ZynqMP SoC, and connent the stream
link of GQSPI to CSU DMA.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-4-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are some coding convention warnings in xlnx-zynqmp.c and
xlnx-zynqmp.h, as reported by:
$ ./scripts/checkpatch.pl include/hw/arm/xlnx-zynqmp.h
$ ./scripts/checkpatch.pl hw/arm/xlnx-zynqmp.c
Let's clean them up.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-3-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The 'running' argument from VMChangeStateHandler does not require
other value than 0 / 1. Make it a plain boolean.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210111152020.1422021-3-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
runstate_check() returns a boolean. runstate_is_running()
returns what runstate_check() returns, also a boolean.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210111152020.1422021-2-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Recent changes allowed the pSeries machine to rollback the hotunplug
process for the DIMM when the guest kernel signals, via a
reconfiguration of the DR connector, that it's not going to release the
LMBs.
Let's also warn QAPI listerners about it. One place to do it would be
right after the unplug state is cleaned up,
spapr_clear_pending_dimm_unplug_state(). This would mean that the
function is now doing more than cleaning up the pending dimm state
though.
This patch does the following changes in spapr.c:
- send a QAPI event to inform that we experienced a failure in the
hotunplug of the DIMM;
- rename spapr_clear_pending_dimm_unplug_state() to
spapr_memory_unplug_rollback(). This is a better fit for what the
function is now doing, and it makes callers care more about what the
function goal is and less about spapr.c internals such as clearing
the pending dimm unplug state.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210302141019.153729-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The pSeries machine is using QEMUTimer internals to return the timeout
in seconds for a timer object, in hw/ppc/spapr.c, function
spapr_drc_unplug_timeout_remaining_sec().
Create a helper in qemu-timer.c to retrieve the deadline for a QEMUTimer
object, in ms, to avoid exposing timer internals to the PPC code.
CC: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210301124133.23800-2-danielhb413@gmail.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Handling errors in memory hotunplug in the pSeries machine is more
complex than any other device type, because there are all the
complications that other devices has, and more.
For instance, determining a timeout for a DIMM hotunplug must consider
if it's a Hash-MMU or a Radix-MMU guest, because Hash guests takes
longer to hotunplug DIMMs. The size of the DIMM is also a factor, given
that longer DIMMs naturally takes longer to be hotunplugged from the
kernel. And there's also the guest memory usage to be considered: if
there's a process that is consuming memory that would be lost by the
DIMM unplug, the kernel will postpone the unplug process until the
process finishes, and then initiate the regular hotunplug process. The
first two considerations are manageable, but the last one is a deal
breaker.
There is no sane way for the pSeries machine to determine the memory
load in the guest when attempting a DIMM hotunplug - and even if there
was a way, the guest can start using all the RAM in the middle of the
unplug process and invalidate our previous assumptions - and in result
we can't even begin to calculate a timeout for the operation. This means
that we can't implement a viable timeout mechanism for memory unplug in
pSeries.
Going back to why we would consider an unplug timeout, the reason is
that we can't know if the kernel is giving up the unplug. Turns out
that, sometimes, we can. Consider a failed memory hotunplug attempt
where the kernel will error out with the following message:
'pseries-hotplug-mem: Memory indexed-count-remove failed, adding any
removed LMBs'
This happens when there is a LMB that the kernel gave up in removing,
and the LMBs previously marked for removal are now being added back.
This happens in the pseries kernel in [1], dlpar_memory_remove_by_ic()
into dlpar_add_lmb(), and after that update_lmb_associativity_index().
In this function, the kernel is configuring the LMB DRC connector again.
Note that this is a valid usage in LOPAR, as stated in section
"ibm,configure-connector RTAS Call":
'A subsequent sequence of calls to ibm,configure-connector with the same
entry from the “ibm,drc-indexes” or “ibm,drc-info” property will restart
the configuration of devices which were not completely configured.'
We can use this kernel behavior in our favor. If a DRC connector
reconfiguration for a LMB that we marked as unplug pending happens, this
indicates that the kernel changed its mind about the unplug and is
reasserting that it will keep using all the LMBs of the DIMM. In this
case, it's safe to assume that the whole DIMM device unplug was
cancelled.
This patch hops into rtas_ibm_configure_connector() and, in the scenario
described above, clear the unplug state for the DIMM device. This will
not solve all the problems we still have with memory unplug, but it will
cover this case where the kernel reconfigures LMBs after a failed
unplug. We are a bit more resilient, without using an unreliable
timeout, and we didn't make the remaining error cases any worse.
[1] arch/powerpc/platforms/pseries/hotplug-memory.c
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-6-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
There is a reliable way to make a CPU hotunplug fail in the pseries
machine. Hotplug a CPU A, then offline all other CPUs inside the guest
but A. When trying to hotunplug A the guest kernel will refuse to do it,
because A is now the last online CPU of the guest. PAPR has no 'error
callback' in this situation to report back to the platform, so the guest
kernel will deny the unplug in silent and QEMU will never know what
happened. The unplug pending state of A will remain until the guest is
shutdown or rebooted.
Previous attempts of fixing it (see [1] and [2]) were aimed at trying to
mitigate the effects of the problem. In [1] we were trying to guess
which guest CPUs were online to forbid hotunplug of the last online CPU
in the QEMU layer, avoiding the scenario described above because QEMU is
now failing in behalf of the guest. This is not robust because the last
online CPU of the guest can change while we're in the middle of the
unplug process, and our initial assumptions are now invalid. In [2] we
were accepting that our unplug process is uncertain and the user should
be allowed to spam the IRQ hotunplug queue of the guest in case the CPU
hotunplug fails.
This patch presents another alternative, using the timeout
infrastructure introduced in the previous patch. CPU hotunplugs in the
pSeries machine will now timeout after 15 seconds. This is a long time
for a single CPU unplug to occur, regardless of guest load - although
the user is *strongly* encouraged to *not* hotunplug devices from a
guest under high load - and we can be sure that something went wrong if
it takes longer than that for the guest to release the CPU (the same
can't be said about memory hotunplug - more on that in the next patch).
Timing out the unplug operation will reset the unplug state of the CPU
and allow the user to try it again, regardless of the error situation
that prevented the hotunplug to occur. Of all the not so pretty
fixes/mitigations for CPU hotunplug errors in pSeries, timing out the
operation is an admission that we have no control in the process, and
must assume the worst case if the operation doesn't succeed in a
sensible time frame.
[1] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg03353.html
[2] https://lists.gnu.org/archive/html/qemu-devel/2021-01/msg04400.html
Reported-by: Xujun Ma <xuma@redhat.com>
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=1911414
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-5-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The LoPAR spec provides no way for the guest kernel to report failure of
hotplug/hotunplug events. This wouldn't be bad if those operations were
granted to always succeed, but that's far for the reality.
What ends up happening is that, in the case of a failed hotunplug,
regardless of whether it was a QEMU error or a guest misbehavior, the
pSeries machine is retaining the unplug state of the device in the
running guest. This state is cleanup in machine reset, where it is
assumed that this state represents a device that is pending unplug, and
the device is hotunpluged from the board. Until the reset occurs, any
hotunplug operation of the same device is forbid because there is a
pending unplug state.
This behavior has at least one undesirable side effect. A long standing
pending unplug state is, more often than not, the result of a hotunplug
error. The user had to dealt with it, since retrying to unplug the
device is noy allowed, and then in the machine reset we're removing the
device from the guest. This means that we're failing the user twice -
failed to hotunplug when asked, then hotunplugged without notice.
Solutions to this problem range between trying to predict when the
hotunplug will fail and forbid the operation from the QEMU layer, from
opening up the IRQ queue to allow for multiple hotunplug attempts, from
telling the users to 'reboot the machine if something goes wrong'. The
first solution is flawed because we can't fully predict guest behavior
from QEMU, the second solution is a trial and error remediation that
counts on a hope that the unplug will eventually succeed, and the third
is ... well.
This patch introduces a crude, but effective solution to hotunplug
errors in the pSeries machine. For each unplug done, we'll timeout after
some time. If a certain amount of time passes, we'll cleanup the
hotunplug state from the machine. During the timeout period, any unplug
operations in the same device will still be blocked. After that, we'll
assume that the guest failed the operation, and allow the user to try
again. If the timeout is too short we'll prevent legitimate hotunplug
situations to occur, so we'll need to overestimate the regular time an
unplug operation takes to succeed to account that.
The true solution for the hotunplug errors in the pSeries machines is a
PAPR change to allow for the guest to warn the platform about it. For
now, the work done in this timeout design can be used for the new PAPR
'abort hcall' in the future, given that for both cases we'll need code
to cleanup the existing unplug states of the DRCs.
At this moment we're adding the basic wiring of the timer into the DRC.
Next patch will use the timer to timeout failed CPU hotunplugs.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-4-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_drc_detach() is not the best name for what the function does. The
function does not detach the DRC, it makes an uncommited attempt to do
it. It'll mark the DRC as pending unplug, via the 'unplug_request'
flag, and only if the DRC state is drck->empty_state it will detach the
DRC, via spapr_drc_release().
This is a contrast with its pair spapr_drc_attach(), where the function
is indeed creating the DRC QOM object. If you know what
spapr_drc_attach() does, you can be misled into thinking that
spapr_drc_detach() is removing the DRC from QEMU internal state, which
isn't true.
The current role of this function is better described as a request for
detach, since there's no guarantee that we're going to detach the DRC in
the end. Rename the function to spapr_drc_unplug_request to reflect
what is is doing.
The initial idea was to change the name to spapr_drc_detach_request(),
and later on change the unplug_request flag to detach_request. However,
unplug_request is a migratable boolean for a long time now and renaming
it is not worth the trouble. spapr_drc_unplug_request() setting
drc->unplug_request is more natural than spapr_drc_detach_request
setting drc->unplug_request.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210222194531.62717-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Update the common copyright string that we use in
-version reports, About dialogs, etc, to 2021.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210309162258.28633-1-peter.maydell@linaro.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We forward-declare Object typedef in "qemu/typedefs.h" since commit
ca27b5eb7c ("qom/object: Move Object typedef to 'qemu/typedefs.h'").
Use it everywhere to make the code simpler.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210225182003.3629342-1-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
We already got a global function called id_generate() to create unique
IDs within QEMU. Let's use it in the network subsytem, too, instead of
inventing our own ID scheme here.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20210215090225.1046239-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
An assorted set of spelling fixes in various places.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20210309111510.79495-1-mjt@msgid.tls.msk.ru>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCgA8FiEEzGIauY6CIA2RXMnEW8LFb64PMh8FAmBEwfEeHG1hcmsuY2F2
ZS1heWxhbmRAaWxhbmRlLmNvLnVrAAoJEFvCxW+uDzIfYZYH/AwOuqycV9XI1s3K
valsExtSmcj6oTrFTSyak0U7QL9G5pm40qEHwQkwFwYecaQXfFNMN1Mt4gYpsLai
JNhV29tzWrQtNFepCjvvuJihDY5IC/3NWyrWqYXRNZ5IGMvde3HUcg210bFOC3mf
iOtZ40ZjBspTwG4eJCOLBBDeXVAMkVUjdfqtsq66zGteHsJjNEpso0HLdMvlFkud
QLF4g06h8iFMxwahZYEwY+fKUHphqfZn8INr01ODQIy3nBGVgenKz9DKPw/pg/UD
nfxhuYwftDof65JpYEhClOWas3AztFJ1YyyP/cibwosLBQVphj3R05/kF6VuyuyP
gZjux0w=
=RPt3
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mcayland/tags/qemu-sparc-20210307' into staging
qemu-sparc queue
# gpg: Signature made Sun 07 Mar 2021 12:07:13 GMT
# gpg: using RSA key CC621AB98E82200D915CC9C45BC2C56FAE0F321F
# gpg: issuer "mark.cave-ayland@ilande.co.uk"
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>" [full]
# Primary key fingerprint: CC62 1AB9 8E82 200D 915C C9C4 5BC2 C56F AE0F 321F
* remotes/mcayland/tags/qemu-sparc-20210307: (42 commits)
esp: add support for unaligned accesses
esp: implement non-DMA transfers in PDMA mode
esp: add trivial implementation of the ESP_RFLAGS register
esp: convert cmdbuf from array to Fifo8
esp: convert ti_buf from array to Fifo8
esp: transition to message out phase after SATN and stop command
esp: add maxlen parameter to get_cmd()
esp: raise interrupt after every non-DMA byte transferred to the FIFO
esp: remove old deferred command completion mechanism
esp: defer command completion interrupt on incoming data transfers
esp: latch individual bits in ESP_RINTR register
esp: implement FIFO flush command
esp: add 4 byte PDMA read and write transfers
esp: remove pdma_origin from ESPState
esp: use FIFO for PDMA transfers between initiator and device
esp: fix PDMA target selection
esp: rename get_cmd_cb() to esp_select()
esp: remove CMD pdma_origin
esp: use in-built TC to determine PDMA transfer length
esp: use ti_wptr/ti_rptr to manage the current FIFO position for PDMA
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Keyboard-Controller-Style devices for IPMI purposes are exposed via LPC
IO cycles from the BMC to the host.
Expose support on the BMC side by implementing the usual MMIO
behaviours, and expose the ability to inspect the KCS registers in
"host" style by accessing QOM properties associated with each register.
The model caters to the IRQ style of both the AST2600 and the earlier
SoCs (AST2400 and AST2500). The AST2600 allocates an IRQ for each LPC
sub-device, while there is a single IRQ shared across all subdevices on
the AST2400 and AST2500.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210302014317.915120-6-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is a very minimal framework to access registers which are used to
configure the AHB memory mapping of the flash chips on the LPC HC
Firmware address space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-Id: <20210302014317.915120-5-andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
TILE-Gx was only implemented in linux-user mode, but support for this CPU
was removed from the upstream Linux kernel in 2018, and it has also been
dropped from glibc, so there is no new Linux development taking place with
this architecture. For running the old binaries, users can simply use older
versions of QEMU.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210224183952.80463-1-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Support Identify command for Namespace attached controller list. This
command handler will traverse the controller instances in the given
subsystem to figure out whether the specified nsid is attached to the
controllers or not.
The 4096bytes Identify data will return with the first entry (16bits)
indicating the number of the controller id entries. So, the data can
hold up to 2047 entries for the controller ids.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
[k.jensen: rebased for dma refactor]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
If namespace inventory is changed due to some reasons (e.g., namespace
attachment/detachment), controller can send out event notifier to the
host to manage namespaces.
This patch sends out the AEN to the host after either attach or detach
namespaces from controllers. To support clear of the event from the
controller, this patch also implemented Get Log Page command for Changed
Namespace List log type. To return namespace id list through the
command, when namespace inventory is updated, id is added to the
per-controller list (changed_ns_list).
To indicate the support of this async event, this patch set
OAES(Optional Asynchronous Events Supported) in Identify Controller data
structure.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This patch supports Namespace Attachment command for the pre-defined
nvme-ns device nodes. Of course, attach/detach namespace should only be
supported in case 'subsys' is given. This is because if we detach a
namespace from a controller, somebody needs to manage the detached, but
allocated namespace in the NVMe subsystem.
As command effect for the namespace attachment command is registered,
the host will be notified that namespace inventory is changed so that
host will rescan the namespace inventory after this command. For
example, kernel driver manages this command effect via passthru IOCTL.
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
[k.jensen: rebased for dma refactor]
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Dataset Management is not subject to MDTS, but exceeded a certain size
per range causes internal looping. Report this limit (DMRSL) in the NVM
command set specific identify controller data structure.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Add support for using the broadcast nsid to issue a flush on all
namespaces through a single command.
Signed-off-by: Gollu Appalanaidu <anaidu.gollu@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add new data structures and types for the Simple Copy command.
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Added Namespace Multi-path I/O and Namespace Sharing Capabilities (NMIC)
field to support shared namespace from controller(s).
This field is in Identify Namespace data structure in [30].
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Added Controller Multi-path I/O and Namespace Sharing Capabilities
(CMIC) field to support multi-controller in the following patches.
This field is in Identify Controller data structure in [76].
Signed-off-by: Minwoo Im <minwoo.im.dev@gmail.com>
Tested-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Klaus Jensen <k.jensen@samsung.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Better to return status together with setting errp. It allows to avoid
error propagation in the caller.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Alberto Garcia <berto@igalia.com>
Message-Id: <20210202124956.63146-8-vsementsov@virtuozzo.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
ZynqMP QSPI supports SPI transfer using DMA mode, but currently this
is unimplemented. When QSPI is programmed to use DMA mode, QEMU will
crash. This is observed when testing VxWorks 7.
This adds a Xilinx CSU DMA model and the implementation is based on
https://github.com/Xilinx/qemu/blob/master/hw/dma/csu_stream_dma.c.
The DST part of the model is verified along with ZynqMP GQSPI model.
Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20210303135254.3970-2-bmeng.cn@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For the AN547 image, the FPGAIO block has an extra DBGCTRL register,
which is used to control the SPNIDEN, SPIDEN, NPIDEN and DBGEN inputs
to the CPU. These signals control when the CPU permits use of the
external debug interface. Our CPU models don't implement the
external debug interface, so we model the register as
reads-as-written.
Implement the register, with a property defining whether it is
present, and allow mps2-tz boards to specify that it is present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-39-peter.maydell@linaro.org
Now we have sufficiently parameterised the code, we can add SSE-300
support by adding a new entry to the armsse_variants[] array.
Note that the main watchdog (unlike the s32k watchdog) in the SSE-300
is a different device from the CMSDK watchdog; we don't have a model
of it so we leave it as a TYPE_UNIMPLEMENTED_DEVICE stub.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-36-peter.maydell@linaro.org
Support SSE variants like the SSE-300 with an ARMSSE_CPU_PWRCTRL register
block. Because this block is per-CPU and does not clash with any of the
SSE-200 devices, we handle it with a has_cpu_pwrctrl flag like the
existing has_cachectrl, has_cpusectrl and has_cpuid, rather than
trying to add per-CPU-device support to the devinfo array handling code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-35-peter.maydell@linaro.org
The SSE-300 has four timers of type TYPE_SSE_TIMER; add support in
the code for having these in an ARMSSEDeviceInfo array.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-34-peter.maydell@linaro.org
The SSE-300 has a system counter device; add support for SSE
variants having this device.
As with the existing devices like the cache control block, CPUID
block, etc, we don't try to make the MMIO addresses configurable. We
can do that if and when we need to model a future SSE variant which
has the counter in a different location.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-33-peter.maydell@linaro.org
We forgot to implement a TYPE_UNIMPLEMENTED_DEVICE stub
for the SYS_PPU in the SSE-200, which is at 0x50022000.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-31-peter.maydell@linaro.org
Move the PPUs into the data-driven device placement framework.
We don't implement them, so they are just TYPE_UNIMPLEMENTED stubs.
Because the SSE-200 and the IotKit diverge here (the IoTKit does
not have the PPUs) we need to separate out the ARMSSEDeviceInfo
for the two variants, and only add the PPUs to the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-30-peter.maydell@linaro.org
Move the CMSDK timer that uses the S32K slow clock into the data-driven
device placement framework.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-27-peter.maydell@linaro.org
Move the CMSDK watchdog device handling into the data-driven device
placement framework. This is slightly more complicated because these
devices might wire their IRQs up to the NMI line, and because one of
them uses the slow 32KHz clock rather than the main clock.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-26-peter.maydell@linaro.org
The SSE-300 is mostly the same as the SSE-200, but it has moved some
of the devices in the memory map and uses different device types in
some cases. To accommodate this, add a framework where the placement
and wiring of some devices can be specified in a data table.
This commit adds the framework for this data-driven device placement,
and makes the CMSDK APB timer devices use it. Subsequent commits
will convert the other devices which differ between SSE-200 and
SSE-300.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-24-peter.maydell@linaro.org
The SSE uses 32 interrupts for its own devices, and then passes through
its expansion IRQ inputs to the CPU's interrupts 33 and upward.
Add a define for the number of IRQs the SSE uses for itself, instead
of hardcoding 32.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-23-peter.maydell@linaro.org
Convert the apb_ppc0 and apb_ppc1 fields in the ARMSSE state struct
to use an array instead of two separate fields. We already had one
place in the code that wanted to be able to refer to the PPC by
index, and we're about to add more code like that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-22-peter.maydell@linaro.org
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one
instance of this per CPU in the system (so just one for the SSE-300),
and as well as the usual CIDR/PIDR ID registers it has just one
register, CPUPWRCFG. This register allows the guest to configure
behaviour of the system in power-down and deep-sleep states. Since
QEMU does not model those, we make the register a dummy
reads-as-written implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
The sysctl PDCM_PD_*_SENSE registers control various power domains in
the system and allow the guest to configure which conditions keep a
power domain awake and what power state to use when the domain is in
a low power state. QEMU doesn't model power domains, so for us these
registers are dummy reads-as-written implementations.
The SSE-300 has a different power domain setup, so the set of
registers is slightly different:
Offset SSE-200 SSE-300
---------------------------------------------------
0x200 PDCM_PD_SYS_SENSE PDCM_PD_SYS_SENSE
0x204 reserved PDCM_PD_CPU0_SENSE
0x208 reserved reserved
0x20c PDCM_PD_SRAM0_SENSE reserved
0x210 PDCM_PD_SRAM1_SENSE reserved
0x214 PDCM_PD_SRAM2_SENSE PDCM_PD_VMR0_SENSE
0x218 PDCM_PD_SRAM3_SENSE PDCM_PD_VMR1_SENSE
Offsets 0x200 and 0x208 are the same for both, so handled in a
previous commit; here we deal with 0x204, 0x20c, 0x210, 0x214, 0x218.
(We can safely add new lines to the SSE300 vmstate because no board
uses this device in an SSE300 yet.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-18-peter.maydell@linaro.org
The SSE-300 has a new PWRCTRL register at offset 0x1fc (previously
reserved). This register controls accessibility of some registers
in the Power Policy Units (PPUs). Since QEMU doesn't implement
the PPUs, we don't need to implement any real behaviour for this
register, so we just handle the UNLOCK bit which controls whether
writes to the register itself are permitted and otherwise make it
be reads-as-written.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-17-peter.maydell@linaro.org
The SSE-300 includes some timers which are a different kind to
those in the SSE-200. Model them.
These timers are documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-13-peter.maydell@linaro.org
The SSE-300 includes a counter module; implement a model of it.
This counter is documented in the SSE-123 Example Subsystem
Technical Reference Manual:
https://developer.arm.com/documentation/101370/latest/
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-12-peter.maydell@linaro.org
For SSE-300, the SYSINFO register block has two new registers:
* SYS_CONFIG1 indicates the config for a potential CPU2 and CPU3;
since the SSE-300 can only be configured with a single CPU it
is always zero
* IIDR is the subsystem implementation identity register;
its value is set by the SoC integrator, so we plumb this in from
the armsse.c code as we do with SYS_VERSION and SYS_CONFIG
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-11-peter.maydell@linaro.org
The version of the SYSINFO Register Block in the SSE-300 has
different CIDR/PIDR register values to the SSE-200; pass in
the sse-version property and use it to select the correct
ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-9-peter.maydell@linaro.org
The versions of the Secure Access Configuration Register Block
and Non-secure Access Configuration Register Block in the SSE-300
are the same as those in the SSE-200, but the CIDR/PIDR ID
register values are different.
Plumb through the sse-version property and use it to select
the correct ID register values.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-8-peter.maydell@linaro.org
Remove the is_sse200 flag in favour of just directly testing the new
sse_version field.
Since some of these registers exist in the SSE-300 but some do not or
have different behaviour, we expand out the if() statements in the
read and write functions into switch()es, so we have an easy place to
put SSE-300 specific behaviour.
(Until we do add the SSE-300 behaviour, the thing preventing us
reaching the "unreachable" default cases is that armsse.c doesn't
yet pass us an ARMSSE_SSE300 version.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-7-peter.maydell@linaro.org
We model Arm "Subsystems for Embedded" SoC subsystems using generic
code which is split into various sub-devices which are configurable
by QOM properties to handle the behaviour differences between the SSE
subsystems we implement. Currently the only sub-device which needs
to change is the IOTKIT_SYSCTL device, and we do this with a mix of
properties that directly specify divergent behaviours (eg
CPUWAIT_RST) and passing it the SYS_VERSION register value as a way
for it to distinguish IoTKit from SSE-200.
The "pass SYS_VERSION" approach is already a bit hacky, since the
IOTKIT_SYSCTL device has to know that the different part of the
register value happens to be bits [31:28]. For SSE-300 this register
is renamed SOC_IDENTITY and has a different format entirely, all of
whose fields can be configured by the SoC integrator when they
integrate the SSE into their SoC, and so "pass SYS_VERSION" breaks
down completely.
Switch to using a simple integer property representing an
internal-to-QEMU enumeration of the SSE flavour. For the moment we
only need this in IOTKIT_SYSCTL, but as we add SSE-300 support a few
of the other devices will also need to know.
We define and permit a value for the SSE-300 so we can start using
it in subsequent commits which add SSE-300 support.
The now-redundant is_sse200 flag in IoTKitSysCtl will be removed
in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-6-peter.maydell@linaro.org
Add a clock_ns_to_ticks() function which does the opposite of
clock_ticks_to_ns(): given a duration in nanoseconds, it returns the
number of clock ticks that would happen in that time. This is useful
for devices that have a free running counter register whose value can
be calculated when it is read.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144617.4782-4-peter.maydell@linaro.org
Add a new callback event type ClockPreUpdate, which is called on
period changes before the period is updated.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144617.4782-3-peter.maydell@linaro.org
The Clock framework allows users to specify a callback which is
called after the clock's period has been updated. Some users need to
also have a callback which is called before the clock period is
updated.
As the first step in adding support for notifying Clock users on
pre-update events, add an argument to the ClockCallback to specify
what event is being notified, and add an argument to the various
functions for registering a callback to specify which events are
of interest to that callback.
Note that the documentation update renders correct the previously
incorrect claim in 'Adding a new clock' that callbacks "will be
explained in a following section".
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210219144617.4782-2-peter.maydell@linaro.org
Rename bytes_covered_by_bitmap_cluster() to
bdrv_dirty_bitmap_serialization_coverage() and make it public.
It is needed as we are going to share it with bitmap loading in
parallels format.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Denis V. Lunev <den@openvz.org>
Message-Id: <20210224104707.88430-2-vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* sbsa-ref: remove cortex-a53 from list of supported cpus
* sbsa-ref: add 'max' to list of allowed cpus
* target/arm: Add support for FEAT_SSBS, Speculative Store Bypass Safe
* npcm7xx: add EMC model
* xlnx-zynqmp: Remove obsolete 'has_rpu' property
* target/arm: Speed up aarch64 TBL/TBX
* virtio-mmio: improve virtio-mmio get_dev_path alog
* target/arm: Use TCF0 and TFSRE0 for unprivileged tag checks
* target/arm: Restrict v8M IDAU to TCG
* target/arm/cpu: Update coding style to make checkpatch.pl happy
* musicpal, tc6393xb, omap_lcdc, tcx: drop dead code for non-32-bit-RGB surfaces
* Add new board: mps3-an524
-----BEGIN PGP SIGNATURE-----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=nphT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210308' into staging
target-arm queue:
* sbsa-ref: remove cortex-a53 from list of supported cpus
* sbsa-ref: add 'max' to list of allowed cpus
* target/arm: Add support for FEAT_SSBS, Speculative Store Bypass Safe
* npcm7xx: add EMC model
* xlnx-zynqmp: Remove obsolete 'has_rpu' property
* target/arm: Speed up aarch64 TBL/TBX
* virtio-mmio: improve virtio-mmio get_dev_path alog
* target/arm: Use TCF0 and TFSRE0 for unprivileged tag checks
* target/arm: Restrict v8M IDAU to TCG
* target/arm/cpu: Update coding style to make checkpatch.pl happy
* musicpal, tc6393xb, omap_lcdc, tcx: drop dead code for non-32-bit-RGB surfaces
* Add new board: mps3-an524
# gpg: Signature made Mon 08 Mar 2021 11:56:24 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210308: (49 commits)
hw/arm/mps2: Update old infocenter.arm.com URLs
docs/system/arm/mps2.rst: Document the new mps3-an524 board
hw/arm/mps2-tz: Provide PL031 RTC on mps3-an524
hw/arm/mps2-tz: Stub out USB controller for mps3-an524
hw/arm/mps2-tz: Add new mps3-an524 board
hw/arm/mps2-tz: Get armv7m_load_kernel() size argument from RAMInfo
hw/arm/mps2-tz: Support ROMs as well as RAMs
hw/arm/mps2-tz: Set MachineClass default_ram info from RAMInfo data
hw/arm/mps2-tz: Make RAM arrangement board-specific
hw/arm/mps2-tz: Allow boards to have different PPCInfo data
hw/arm/mps2-tz: Size the uart-irq-orgate based on the number of UARTs
hw/arm/mps2-tz: Move device IRQ info to data structures
hw/arm/mps2-tz: Allow PPCPortInfo structures to specify device interrupts
hw/arm/mps2-tz: Correct wrong interrupt numbers for DMA and SPI
hw/misc/mps2-scc: Implement CFG_REG5 and CFG_REG6 for MPS3 AN524
hw/arm/mps2-tz: Make number of IRQs board-specific
hw/arm/mps2-tz: Condition IRQ splitting on number of CPUs, not board type
hw/arm/mps2-tz: Make FPGAIO switch and LED config per-board
hw/misc/mps2-fpgaio: Support SWITCH register
hw/misc/mps2-fpgaio: Make number of LEDs configurable by board
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Update old infocenter.arm.com URLs to the equivalent developer.arm.com
ones (the old URLs should redirect, but we might as well avoid the
redirection notice, and the new URLs are pleasantly shorter).
This commit covers the links to the MPS2 board TRM, the various
Application Notes, the IoTKit and SSE-200 documents.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-25-peter.maydell@linaro.org
The MacOS toolbox ROM uses non-DMA TI commands to handle the first/last byte
of an unaligned 16-bit transfer to memory.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-42-mark.cave-ayland@ilande.co.uk>
Rename ESP_CMDBUF_SZ to ESP_CMDFIFO_SZ and cmdbuf_cdb_offset to cmdfifo_cdb_offset
to indicate that the command buffer type has changed from an array to a Fifo8.
This also enables us to remove the ESPState field cmdlen since the command length
is now simply the number of elements used in cmdfifo.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-40-mark.cave-ayland@ilande.co.uk>
Rename TI_BUFSZ to ESP_FIFO_SZ since this constant is really describing the size
of the FIFO and is not directly related to the TI size.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-39-mark.cave-ayland@ilande.co.uk>
The SCSI bus should remain in the message out phase after the SATN and stop
command rather than transitioning to the command phase. A new ESPState variable
cmdbuf_cdb_offset is added which stores the offset of the CDB from the start
of cmdbuf when accumulating extended message out phase data.
Currently any extended message out data is discarded in do_cmd() before the CDB
is processed in do_busid_cmd().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-38-mark.cave-ayland@ilande.co.uk>
Commit ea84a44250 "scsi: esp: Defer command completion until previous interrupts
have been handled" provided a mechanism to delay the command completion interrupt
until ESP_RINTR is read after the command has completed.
With the previous fixes for latching the ESP_RINTR bits and deferring the setting
of the command completion interrupt for incoming data to the SCSI callback, this
workaround is no longer required and can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-35-mark.cave-ayland@ilande.co.uk>
The MacOS toolbox ROM issues a command to the ESP controller as part of its
"FAST" SCSI routines and then proceeds to read the incoming data soon after
receiving the command completion interrupt.
Unfortunately due to SCSI block transfers being asynchronous the incoming data
may not yet be present causing an underflow error. Resolve this by waiting for
the SCSI subsystem transfer_data callback before raising the command completion
interrupt.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-34-mark.cave-ayland@ilande.co.uk>
Now that all data is transferred via the FIFO (ti_buf) there is no need to track
the source buffer being used for the data transfer. This also eliminates the
need for a separate subsection for PDMA state migration.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-30-mark.cave-ayland@ilande.co.uk>
The cmdbuf is really just a copy of FIFO data (including extra message phase
bytes) so its pdma_origin is effectively TI. Fortunately we already know when
we are receiving a SCSI command since do_cmd == 1 which enables us to
distinguish between the two cases in esp_pdma_read()/esp_pdma_write().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-26-mark.cave-ayland@ilande.co.uk>
Real hardware simply counts down using the in-built TC to determine when the
the PDMA request is complete. Use the TC to determine the PDMA transfer length
which then enables us to remove the redundant pdma_len variable.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-25-mark.cave-ayland@ilande.co.uk>
This eliminates the last user of the PDMA-specific pdma_cur variable which can
now be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-24-mark.cave-ayland@ilande.co.uk>
Now that PDMA SCSI commands are accumulated in cmdbuf in the same way as normal
commands, the existing logic for locating the start of the SCSI command in
cmdbuf via cmdlen can be used. This enables the PDMA-specific pdma_start and
also get_pdma_buf() to be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-22-mark.cave-ayland@ilande.co.uk>
ESP SCSI commands are already accumulated in cmdbuf and so there is no need to
keep a separate pdma_buf buffer. Accumulate SCSI commands for PDMA transfers in
cmdbuf instead of pdma_buf so update cmdlen accordingly and change pdma_origin
for PDMA transfers to CMD which allows the PDMA origin to be removed.
This commit also removes a stray memcpy() from get_cmd() which is a no-op because
cmdlen is always zero at the start of a command.
Notionally the removal of pdma_buf from vmstate_esp_pdma also breaks migration
compatibility for the PDMA subsection until its complete removal by the end of
the series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-19-mark.cave-ayland@ilande.co.uk>
The ESP device already keeps track of the remaining bytes left to transfer via
its TC (transfer counter) register which is decremented for each byte that
is transferred across the SCSI bus.
Switch the transfer logic to use the value of TC instead of dma_left and then
remove dma_left completely, adding logic to the vmstate_esp post_load() function
to transfer the old dma_left value to the TC register during migration from
older versions.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-14-mark.cave-ayland@ilande.co.uk>
The value of dma_counter is set once at the start of the transfer and remains
the same until the transfer is complete. This allows the check in esp_transfer_data
to be simplified since dma_left will always be non-zero until the transfer is
completed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-13-mark.cave-ayland@ilande.co.uk>
The QOM object representing ESPState is currently embedded within both the
SYSBUS_ESP and PCI_ESP devices with migration state handled by embedding
vmstate_esp within each device using VMSTATE_STRUCT.
Since the vmstate_esp fields are embedded directly within the migration
stream, the incoming vmstate_esp version_id is lost. The only version information
available is that from vmstate_sysbus_esp_scsi and vmstate_esp_pci_scsi, but
those versions represent their respective devices and not that of the underlying
ESPState.
Resolve this by adding a new version-dependent field in vmstate_sysbus_esp_scsi
and vmstate_esp_pci_scsi which stores the vmstate_esp version_id field within
ESPState to be used to allow migration from older QEMU versions.
Finally bump the vmstate_esp version to 5 to cover the upcoming ESPState changes
within this patch series.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-5-mark.cave-ayland@ilande.co.uk>
Make this new QOM device state a child device of both the sysbus-esp and esp-pci
implementations.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-4-mark.cave-ayland@ilande.co.uk>
The existing ESP QOM type currently represents a sysbus device with an embedded
ESP state. Rename the type to SYSBUS_ESP accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20210304221103.6369-3-mark.cave-ayland@ilande.co.uk>
Commit 3e7a84eecc ("Hexagon build infrastructure") added Hexagon
definitions that should be poisoned on target independent device
code, but forgot to update "exec/poison.h". Do it now.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Message-Id: <20210219135754.1968100-1-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The primary motivation is to remove a dozen insns along
the fast-path in tb_lookup. As a byproduct, this allows
us to completely remove parallel_cpus.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Lets make sure all the flags we compare when looking up blocks are
together in the same place.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210224165811.11567-5-alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We don't really deal in cf_mask most of the time. The one time it's
relevant is when we want to remove an invalidated TB from the QHT
lookup. Everywhere else we should be looking up things without
CF_INVALID set.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210224165811.11567-4-alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
There is nothing special about this compile flag that doesn't mean we
can't just compute it with curr_cflags() which we should be using when
building a new set.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210224165811.11567-3-alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Having a function return either and valid TB and some system state
seems excessive. It will make the subsequent re-factoring easier if we
lookup the current state where we are.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-Id: <20210224165811.11567-2-alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
This code was introduced in commit 27c7ca7e77,
("SHIX board emulation (Samuel Tardieu)"). Use
the same license.
Cc: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210222141514.2646278-2-f4bug@amsat.org>
The AN524 version of the SCC interface has different behaviour for
some of the CFG registers; implement it.
Each board in this family can have minor differences in the meaning
of the CFG registers, so rather than trying to specify all the
possible semantics via individual device properties, we make the
behaviour conditional on the part-number field of the SCC_ID register
which the board code already passes us.
For the AN524, the differences are:
* CFG3 is reserved rather than being board switches
* CFG5 is a new register ("ACLK Frequency in Hz")
* CFG6 is a new register ("Clock divider for BRAM")
We implement both of the new registers as reads-as-written.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-11-peter.maydell@linaro.org
MPS3 boards have an extra SWITCH register in the FPGAIO block which
reports the value of some switches. Implement this, governed by a
property the board code can use to specify whether whether it exists.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-7-peter.maydell@linaro.org
The MPS2 board has 2 LEDs, but the MPS3 board has 10 LEDs. The
FPGAIO device is similar on both sets of boards, but the LED0
register has correspondingly more bits that have an effect. Add a
device property for number of LEDs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-6-peter.maydell@linaro.org
Currently the MPS2 SCC device implements a fixed number of OSCCLK
values (3). The variant of this device in the MPS3 AN524 board has 6
OSCCLK values. Switch to using a PROP_ARRAY, which allows board code
to specify how large the OSCCLK array should be as well as its
values.
With a variable-length property array, the SCC no longer specifies
default values for the OSCCLKs, so we must set them explicitly in the
board code. This defaults are actually incorrect for the an521 and
an505; we will correct this bug in a following patch.
This is a migration compatibility break for all the mps boards.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210215115138.20465-3-peter.maydell@linaro.org
Some SCSI drivers like virtio have an internal mapping for the
host_status. This patch moves the host_status translation into
the SCSI drivers to allow those drivers to set up the correct
values.
Signed-off-by: Hannes Reinecke <hare@suse.de>.
[Added default handling to avoid touching all drivers. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently sg_io_sense_from_errno() converts the two input parameters
'errno' and 'io_hdr' into sense code and SCSI status. Having
split the function off into scsi_sense_from_errno() and
scsi_sense_from_host_status(), both of which are available generically,
we now inline the logic in the callers so that scsi-disk and
scsi-generic will be able to pass host_status to the HBA.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-7-hare@suse.de>
[Put together from "scsi-disk: Add sg_io callback to evaluate status"
and what remains of "scsi: split sg_io_sense_from_errno() in two functions",
with many other fixes. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As we don't have a driver-specific mapping (yet) we should provide
for a detailed mapping from host_status to SCSI sense codes.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-6-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We really should make a distinction between legitimate sense codes
(ie if one is running against an emulated block device or for
pass-through sense codes), and the intermediate errors generated
during processing of the command, which really are not sense codes
but refer to some specific internal status. And this internal
state is not necessarily linux-specific, but rather can refer to
the qemu implementation itself.
So rename the linux-only SG_ERR codes to SCSI_HOST codes and make
them available generally.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Message-Id: <20201116184041.60465-5-hare@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This enables some simplification of vl.c via error_fatal, and improves
error messages. Before:
$ ./qemu-system-x86_64 -readconfig .
qemu-system-x86_64: error reading file
qemu-system-x86_64: -readconfig .: read config .: Invalid argument
$ /usr/libexec/qemu-kvm -readconfig foo
qemu-kvm: -readconfig foo: read config foo: No such file or directory
After:
$ ./qemu-system-x86_64 -readconfig .
qemu-system-x86_64: -readconfig .: Cannot read config file: Is a directory
$ ./qemu-system-x86_64 -readconfig foo
qemu-system-x86_64: -readconfig foo: Could not open 'foo': No such file or directory
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210226170816.231173-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because sizeof(struct elf64_note) == sizeof(struct elf32_note),
attempting to use the size of the currently defined struct elf_note as
a discriminator for whether the object being loaded is 64 bit in
load_elf() fails.
Instead, take advantage of the existing glue parameter SZ, which is
defined as 32 or 64 in the respective variants of load_elf().
Fixes: 696aa04c84 ("elf-ops.h: Add get_elf_note_type()")
Signed-off-by: David Edmondson <david.edmondson@oracle.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Message-Id: <20210302090315.3031492-2-david.edmondson@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We hint the 'has_rpu' property is no longer required since commit
6908ec448b ("xlnx-zynqmp: Properly support the smp command line
option") which was released in QEMU v2.11.0.
Beside, this device is marked 'user_creatable = false', so the
only thing that could be setting the property is the board code
that creates the device.
Since the property is not user-facing, we can remove it without
going through the deprecation process.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210219144350.1979905-1-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a 10/100 ethernet device that has several features.
Only the ones needed by the Linux driver have been implemented.
See npcm7xx_emc.c for a list of unimplemented features.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Doug Evans <dje@google.com>
Message-id: 20210218212453.831406-3-dje@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a 10/100 ethernet device that has several features.
Only the ones needed by the Linux driver have been implemented.
See npcm7xx_emc.c for a list of unimplemented features.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Avi Fishman <avi.fishman@nuvoton.com>
Signed-off-by: Doug Evans <dje@google.com>
Message-id: 20210218212453.831406-2-dje@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Setting errp = NULL is wrong: the automatic error propagation still
propagates the dangling pointer _auto_errp_prop.local_err. We need to
set *errp = NULL to clear the dangling pointer.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210125132635.1253219-1-armbru@redhat.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
This PR is a collection of RISC-V patches:
- Improvements to SiFive U OTP
- Upgrade OpenSBI to v0.9
- Support the QMP dump-guest-memory
- Add support for the SiFive SPI controller (sifive_u)
- Initial RISC-V system documentation
- A fix for the Goldfish RTC
- MAINTAINERS updates
- Support for high PCIe memory in the virt machine
-----BEGIN PGP SIGNATURE-----
iQEyBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmBA8k8ACgkQIeENKd+X
cFRRMgf41R7Zn1ZSB9GHL3WgLDTPqpT4FAMpTnYRD7wPdspawl1SsHWBgaLNmJWk
dwSLhvHMM44pOVCQRqdkiRrp5t5fDEm6gdRKyNn5uzWFMn7ibYIjmg7OE+79onbN
VES4yTJwuskD/7JRNcrW6RytKRgzKs2au8NxxgtgXprSF0nM9wCu70z4T9XkLfjQ
cpJUUaUCw628uUic/nObTxMnaiEmq/C0qU9SRRKPYVRp7jceCsHMVRazqOgdM6uf
foNHi/uCNKy6I841+D8Po7h57s51LtT78JDRRVRPfWY+SRQyC5l8Eq3UtRPyg39p
7hhkiAKhG4rs8iCXKvMvTz0S//Cx
=BVLq
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20210304' into staging
RISC-V PR for 6.0
This PR is a collection of RISC-V patches:
- Improvements to SiFive U OTP
- Upgrade OpenSBI to v0.9
- Support the QMP dump-guest-memory
- Add support for the SiFive SPI controller (sifive_u)
- Initial RISC-V system documentation
- A fix for the Goldfish RTC
- MAINTAINERS updates
- Support for high PCIe memory in the virt machine
# gpg: Signature made Thu 04 Mar 2021 14:44:31 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210304:
hw/riscv: virt: Map high mmio for PCIe
hw/riscv: virt: Limit RAM size in a 32-bit system
hw/riscv: virt: Drop the 'link_up' parameter of gpex_pcie_init()
hw/riscv: Drop 'struct MemmapEntry'
MAINTAINERS: Add a SiFive machine section
goldfish_rtc: re-arm the alarm after migration
docs/system: riscv: Add documentation for sifive_u machine
docs/system: Add RISC-V documentation
docs/system: Sort targets in alphabetical order
hw/riscv: sifive_u: Change SIFIVE_U_GEM_IRQ to decimal value
hw/riscv: sifive_u: Add QSPI2 controller and connect an SD card
hw/riscv: sifive_u: Add QSPI0 controller and connect a flash
hw/ssi: Add SiFive SPI controller support
hw/block: m25p80: Add various ISSI flash information
hw/block: m25p80: Add ISSI SPI flash support
target-riscv: support QMP dump-guest-memory
roms/opensbi: Upgrade from v0.8 to v0.9
hw/misc: sifive_u_otp: Use error_report() when block operation fails
target/riscv: Declare csr_ops[] with a known size
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All other peripherals' IRQs are in the format of decimal value.
Change SIFIVE_U_GEM_IRQ to be consistent.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-7-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the SiFive SPI controller model for the FU540 SoC.
The direct memory-mapped SPI flash mode is unsupported.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Gerd Hoffmann
Akihiko Odaki
Peter Maydell
Paolo Bonzini
Reinoud Zandijk
Daniel Henrique Barboza
Ravi Bangoria
Vaibhav Jain
BALATON Zoltan
Thomas Huth
Keqian Zhu
Philippe Mathieu-Daudé
Cédric Le Goater
Joel Stanley
Kevin Wolf
Vladimir Sementsov-Ogievskiy
Cornelia Huck
Jason Wang
Patrick Venture
Mark Cave-Ayland
Richard Henderson
Klaus Jensen
Andrey Gruzdev
Lukas Straub
Alexey Kardashevskiy
Laurent Vivier
Gavin Shan
Zihao Chang
Bin Meng
Asherah Connor
Alexander Wagner
Marian Postevca
David Hildenbrand
Igor Mammedov
Bin Meng
Markus Armbruster
Minwoo Im
Gollu Appalanaidu
Daniel P. Berrangé
Yonggang Luo
Alex Bennée
Aaron Lindsay
Marc-André Lureau
Alexander Bulekov
Alexey Kirillov
Andreas Konopik
Hao Wu
Andrew Jones
Eric Auger
Edgar E. Iglesias
Xuzhou Cheng
Philippe Mathieu-Daudé
Michael Tokarev
Andrew Jeffery
Minwoo Im
Hannes Reinecke
David Edmondson
Doug Evans