This commit was generated mechanically by coccinelle from the following
semantic patch:
@@
expression val;
@@
- (ffs(val) - 1)
+ ctz32(val)
The call sites have been audited to ensure the ffs(0) - 1 == -1 case
never occurs (due to input validation, asserts, etc). Therefore we
don't need to worry about the fact that ctz32(0) == 32.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 1427124571-28598-5-git-send-email-stefanha@redhat.com
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This patch adds basic support for the VTB.
PowerISA:
The Virtual Time Base (VTB) is a 64-bit incrementing counter.
Virtual Time Base increments at the same rate as the Time Base until its value
becomes 0xFFFF_FFFF_FFFF_FFFF (2 64 - 1); at the next increment its value
becomes 0x0000_0000_0000_0000. There is no interrupt or other indication when
this occurs.
The operation of the Virtual Time Base has the following additional
properties.
1. Loading a GPR from the Virtual Time Base has no effect on the accuracy of
the Virtual Time Base.
2. Copying the contents of a GPR to the Virtual Time Base replaces the
contents of the Virtual Time Base with the contents of the GPR.
Signed-off-by: Cyril Bur <cyril.bur@au1.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
We look at two sizes specified in ISA (4K, 64K). If not found matching,
we consider it 16MB.
Without this patch we would fail to lookup address above 16MB range.
Below 16MB happened to work before because the kernel have a liner
mapping and we always looked up hash for 0xc000000000000000. The
actual real address was computed by using the 16MB offset
with the real address found with the above hash.
Without Fix:
(gdb) x/16x 0xc000000001000000
0xc000000001000000 <list_entries+453208>: Cannot access memory at address 0xc000000001000000
(gdb)
With Fix:
(gdb) x/16x 0xc000000001000000
0xc000000001000000 <list_entries+453208>: 0x00000000 0x00000000 0x00000000 0x00000000
0xc000000001000010 <list_entries+453224>: 0x00000000 0x00000000 0x00000000 0x00000000
0xc000000001000020 <list_entries+453240>: 0x00000000 0x00000000 0x00000000 0x00000000
0xc000000001000030 <list_entries+453256>: 0x00000000 0x00000000 0x00000000 0x00000000
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The TARGET_HAS_ICE #define is intended to indicate whether a target-*
guest CPU implementation supports the breakpoint handling. However,
all our guest CPUs have that support (the only two which do not
define TARGET_HAS_ICE are unicore32 and openrisc, and in both those
cases the bp support is present and the lack of the #define is just
a bug). So remove the #define entirely: all new guest CPU support
should include breakpoint handling as part of the basic implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1420484960-32365-1-git-send-email-peter.maydell@linaro.org
New year's release. This time's highlights:
- E500: More RAM support
- pseries: New SLOF release
- Migration fixes
- Simplify USB spawning logic, removes support for explicit usb=off
- TCG: Simple untansactional TM emulation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=28q1
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/agraf/tags/signed-ppc-for-upstream' into staging
Patch queue for ppc - 2015-01-07
New year's release. This time's highlights:
- E500: More RAM support
- pseries: New SLOF release
- Migration fixes
- Simplify USB spawning logic, removes support for explicit usb=off
- TCG: Simple untansactional TM emulation
# gpg: Signature made Wed 07 Jan 2015 15:19:37 GMT using RSA key ID 03FEDC60
# gpg: Good signature from "Alexander Graf <agraf@suse.de>"
# gpg: aka "Alexander Graf <alex@csgraf.de>"
* remotes/agraf/tags/signed-ppc-for-upstream: (37 commits)
hw/ppc/mac_newworld: simplify usb controller creation logic
hw/ppc/spapr: simplify usb controller creation logic
hw/ppc/mac_newworld: QOMified mac99 machines
hw/usb: simplified usb_enabled
hw/machine: added machine_usb wrapper
hw/ppc: modified the condition for usb controllers to be created for some ppc machines
target-ppc: Cast ssize_t to size_t before printing with %zx
target-ppc: Mark SR() and gen_sync_exception() as !CONFIG_USER_ONLY
PPC: e500: Fix GPIO controller interrupt number
target-ppc: Introduce Privileged TM Noops
target-ppc: Introduce tcheck
target-ppc: Introduce TM Noops
target-ppc: Introduce tbegin
target-ppc: Introduce TEXASRU Bit Fields
target-ppc: Power8 Supports Transactional Memory
target-ppc: Introduce tm_enabled Bit to CPU State
target-ppc: Introduce Feature Flag for Transactional Memory
target-ppc: Introduce Instruction Type for Transactional Memory
pseries: Update SLOF firmware image to 20141202
PPC: Fix crash on spapr_tce_table_finalize()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Define mnemonics for the various bit fields in the Transaction
EXception And Summary Register (TEXASR).
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add a flag (POWERPC_FLAG_TM) for the Transactional Memory
Facility introduced in Power ISA 2.07.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add a category (PPC2_TM) for the Transactional Memory instructions
introduced in Power ISA 2.07.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Define and use macros instead of direct numbers wherever
possible in ppc opcodes table handling code.
This doesn't change any code functionality.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch remove limitation for fc[tf]id[*] on 32 bits targets and
add a new insn flag for signed integer 64 conversion PPC2_FP_CVT_S64
Signed-off-by: Pierre Mallard <mallard.pierre@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The device endianness is the cpu endianness at device reset time.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Decimal Floating Point is emulated, so add it the mask. This will
fix the erroneous message:
Warning: Disabling some instructions which are not emulated by TCG (0x0, 0x4)
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds handling of the RESOURCE_ADDR_TRANS_MODE resource from
the H_SET_MODE, for POWER8 (PowerISA 2.07) only.
This defines AIL flags for LPCR special register.
This changes @excp_prefix according to the mode, takes effect in TCG.
This turns support of a new capability PPC2_ISA207S flag for TCG.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
POWER8 supports Event-Based Branch Facility (EBB). It is controlled via
set of SPRs access to which should generate an "Facility Unavailable"
interrupt if the facilities are not enabled in FSCR for problem state.
This adds EBB SPRs.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds migration support for registers saved before Transactional
Memory (TM) transaction started.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds TM (Transactional Memory) SPRs.
This adds generic spr_read_prev_upper32()/spr_write_prev_upper32() to
handle upper half SPRs such as TEXASRU which is upper half of TEXASR.
Since this is not the only register like that and their numbers go
consequently, it makes sense to generalize the helpers.
This adds a gen_msr_facility_check() helper which purpose is to generate
the Facility Unavailable exception if the facility is disabled.
It is a copy of gen_fscr_facility_check() but it checks for enabled
facility in MSR rather than FSCR/HFSCR. It still sets the interrupt cause
in FSCR/HFSCR (whichever is passed to the helper).
This adds spr_read_tm/spr_write_tm/spr_read_tm_upper32/spr_write_tm_upper32
which are used for TM SPRs.
This adds TM-relates MSR bits definitions. This enables TM in POWER8 CPU class'
msr_mask.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds POWER8 specific PMU MMCR2/MMCRS SPRs.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds an FSCR (Facility Status and Control Register) SPR. This defines
names for FSCR bits.
This defines new exception type - POWERPC_EXCP_FU - "facility unavailable" (FU).
This registers an interrupt vector for it at 0xF60 as PowerISA defines.
This adds a TCG helper_fscr_facility_check() helper to raise an exception
if the facility is not enabled. It updates the interrupt cause field
in FSCR. This adds a TCG translation block generation code. The helper
may be used for HFSCR too as it has the same format.
The helper raising FU exceptions is not used by this patch but will be
in the next ones.
This adds gen_update_current_nip() to update NIP in DisasContext.
This helper is not used now and will be called before checking for
a condition for throwing an FU exception.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds TIR (Thread Identification Register) SPR first defined for server
CPUs in PowerISA 2.07.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Previously LPCR was registered for the 970 class which was wrong as
it does not have LPCR. Instead, HID4 is used which this patch registers.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Compared to PowerISA-compliant CPUs, 970 family has most of them plus
PMC7/8 which are only present on 970 but not on POWER5 and later CPUs.
Since we are changing SPRs for Book3s/970 families, let's add them too.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since we started adding "POWER" prefix to 64bit PMU SPRs, let's finish
the transition and fix MMCRA and define a supermode version of it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This stops using 7xx common SPRs init function and adds separate set
of helpers for 970.
This does not copy ICTC SPR as neither 970 manual nor PowerISA mention it.
This defines 970/book3s PMU SPRs constants as they differs from the ones
used for 7XX.
This creates 2 helpers for PMU SPRs, one for supermode privileged SPRs and
one for user privileged SPRs as "sup" versions can be shared across
the family while "user" versions will behave different starting POWER8
(which will be addressed later).
This allows writing to Uxxxx SPRs from supermode. spr_write_ureg() is
implemented for this as a copy of already existing spr_read_ureg().
This allows writing to supervisor's SIAR - it used to be disabled
when gen_spr_7xx() was used.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
The differences between classes were:
1. SLB size, was 32 for 970 and 64 for others, should be 64 for all;
2. check_pow() callback, HID0 format is the same so should be the same
0x01C00000 which means "deep nap", "doze" and "nap" bits set;
3. LPCR - 970 does not have it but 970MP had one (by mistake).
This fixes wrong differences and makes one 970 class.
This fixes wrong registration of LPCR which is not present on 970.
This defines HID0 bits and uses them in check_pow_970().
This does not copy MSR_SHV (Hypervisor State, HV) bit from 970FX to
970 class as we do not emulate hypervisor in QEMU anyway.
This does not remove check_pow_970FX now as it is still used by POWER5+
class, this will be addressed later.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
As defined in Linux kernel, PMC*, SIAR, MMCR0/1 have different numbers
for 32 and 64 bit POWERPC. We are going to support 64bit versions too so
let's rename 32bit ones to avoid confusion.
This is a mechanical patch so it does not fix obvious mistake with these
registers in POWER7 yet, this will be fixed later.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Today we have a lot of conditional code in the SPE emulation depending on
whether we have 64bit GPRs or not.
Unfortunately the assumption that we can just recycle the 64bit GPR
implementation is wrong. Normal SPE implementations maintain the upper 32 bits
on all non-SPE instructions which then only modify the low 32 bits. However
all instructions we model that adhere to the normal SF based switching don't
care whether they operate on 32 or 64 bit registers and just always use the full
64 bits.
So let's remove that dubious SPE optimization and revert everything to the same
code path the 32bit target code was taking. That way we get rid of differences
between the two implementations, but will get a slight performance hit when
emulating SPE instructions.
This fixes SPE emulation with qemu-system-ppc64 for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
This puts a limit to the number of threads per core based on the current
compatibility mode. Although PowerISA specs do not specify the maximum
threads per core number, the linux guest still expects that
PowerISA2.05-compatible CPU supports only 2 threads per core as this
is what POWER6 (2.05 compliant CPU) implements, the same is for
POWER7 (2.06, 4 threads) and POWER8 (2.07, 8 threads).
This calls spapr_fixup_cpu_smt_dt() with the maximum allowed number of
threads which affects ibm,ppc-interrupt-server#s and
ibm,ppc-interrupt-gserver#s properties.
The number of CPU nodesremains unchanged.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds basic support for the "compat" CPU option. By specifying
the compat property, the user can manually switch guest CPU mode from
"raw" to "architected".
This defines feature disable bits which are not used yet as, for example,
PowerISA 2.07 says if 2.06 mode is selected, the TM bit does not matter -
transactional memory (TM) will be disabled because 2.06 does not define
it at all. The same is true for VSX and 2.05 mode. So just setting a mode
must be ok.
This does not change the existing behavior as the actual compatibility
mode support is coming in next patches.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[agraf: fix compilation on 32bit hosts]
Signed-off-by: Alexander Graf <agraf@suse.de>
There are 2 L1 cache control registers - one for data (L1CSR0) and
one for instructions (L1CSR1).
Emulate both of them well enough to give the guest the illusion that
it could actually do anything about its caches.
Signed-off-by: Alexander Graf <agraf@suse.de>
In addition to the L1 data cache configuration register L1CFG0 there is
also another one for the L1 instruction cache called L1CFG1.
Emulate that one with the same values as the data one.
Signed-off-by: Alexander Graf <agraf@suse.de>
On the x86, some devices need access to the CPU reset pin (INIT#).
Provide a generic service to do this, using one of the internal
cpu_interrupt targets. Generalize the PPC-specific code for
CPU_INTERRUPT_RESET to other targets.
Since PPC does not support migration across QEMU versions (its
machine types are not versioned yet), I picked the value that
is used on x86, CPU_INTERRUPT_TGT_INT_1. Consequently, TGT_INT_2
and TGT_INT_3 are shifted down by one while keeping their value.
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are 3 different variants of the decrementor for BookE and BookS.
The BookE variant sets TSR[DIS] to 1 when the DEC value becomes 1 or 0. TSR[DIS]
is then the indicator whether the decrementor interrupt line is asserted or not.
The old BookS variant treats DEC as an edge interrupt that gets triggered when
the DEC value's top bit turns 1 from 0.
The new BookS variant maintains the assertion bit inside DEC itself. Whenever
the DEC value becomes negative (top bit set) the DEC interrupt line is asserted.
So far we implemented mostly the old BookS variant. Let's do them all properly.
This fixes booting pseries ppc64 guest images in TCG mode for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
This flag will be used to decide whether to emulate some bits of
H_SET_MODE hypercall because some are POWER8-only.
While we are here, add 2.05 flag to POWER8 family too. POWER7/7+ already
have it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
This resets SPR values to defaults on CPU reset. This should help
with little-endian guests reboot issues.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Note that while such functions may exist both for *-user and softmmu,
only *-user uses the CPUState hook, while softmmu reuses the prototype
for calling it directly.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Default to false.
Tidy variable naming and inline cast uses while at it.
Tested-by: Jia Liu <proljc@gmail.com> (or32)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Normally CPUState::cpu_index is used to pick the right CPU for various
operations. However default consecutive numbering does not always work
for POWERPC.
These indexes are reflected in /proc/device-tree/cpus/PowerPC,POWER7@XX
and used to call KVM VCPU's ioctls. In order to achieve this,
kvmppc_fixup_cpu() was introduced. Roughly speaking, it multiplies
cpu_index by the number of threads per core.
This approach has disadvantages such as:
1. NUMA configuration stays broken after the fixup;
2. CPU-targeted commands from the QEMU Monitor do not work properly as
CPU indexes have been fixed and there is no clear way for the user to
know what the new CPU indexes are.
This introduces a @cpu_dt_id field in the CPUPPCState struct which
is initialized from @cpu_index by default and can be fixed later
to meet the device tree requirements.
This adds an API to handle @cpu_dt_id.
This removes kvmppc_fixup_cpu() as it is not more needed, @cpu_dt_id
is calculated in ppc_cpu_realize().
This will be used later in machine code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Mike Day <ncmike@ncultra.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Correctly update the htab_mask using the return value of
KVM_PPC_ALLOCATE_HTAB ioctl. Also we don't update sdr1
on GET_SREGS for HV. We check for external htab and if
found true, we don't need to update sdr1
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[ fixed pte group offset computation in ppc_hash64_htab_lookup() that
caused TCG to fail, Greg Kurz <gkurz@linux.vnet.ibm.com> ]
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch updates the ppc_avr_t data structure to include elements for
signed 64-bit integers and (conditionally) unsigned 128 bit integers.
These elements will be in instructions models later on in this patch series.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds a flag that will be used to tag the Altivec instructions
introduced in Power ISA Version 2.07.
The flag is added to Power8 model since P8 supports these instructions.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds the Load Quadword and Reserve (lqarx) instruction,
which is new in Power ISA 2.07.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds a flag to identify the load/store quadword instructions
that are introduced with Power ISA 2.07.
The flag is added to the Power8 model since P8 supports these
instructions.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds support for the Target Address Register (TAR) to the Power8
model.
Because supported SPRs are typically identified in an init_proc_*()
function and because the Power8 model is currently just using the
init_proc_POWER7() function, a new init_proc_POWER8() function
is added and plugged into the P8 model.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds a flag for the bctar instruction. This instruction
is being introduced via Power ISA 2.07.
Also, the flag is added to the Power8 machine model since the P8
processor supports this instruction.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds a flag for Floating Point Test instructions that were
introduced in Power ISA V2.06B.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds a flag for the floating point conversion instructions
introduced in Power ISA 2.06B.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds a flag for the atomic instructions introduced
in Power ISA V2.06B.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds a flag for the Divide Extended instructions that
were introduced in Power ISA V2.06B. The flag is added to the
Power7 and Power8 models.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds the Bit Permute Doubleword (bpermd) instruction,
which was introduced in Power ISA 2.06 as part of the base 64-bit
architecture.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds a flag to identify those VSX instructions that are
new to Power ISA V2.07. The flag is added to the Power 8 processor
initialization so that the P8 models understand how to decode and
emulate instructions in this category.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
Assuming that "U" in SPR_UCTRL is for "user", there is inconsistency with
970 user manuals/P5-bookIV/PowerISA204 which define the number as:
priviledged
# spr5-9 spr0-4 name mtspr mfspr len cat
136 00100 01000 CTRL - no 32 S
152 00100 11000 CTRL yes - 32 S
This swaps the numbers. No effect from this change is expected though.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
PowerISA defines LPCR SPR number as 318=0x13E but QEMU uses the value of
316.
This fixes the definition of LPCR SPR.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds support for the VSX bit of the PowerPC Machine
State Register (MSR) as well as the corresponding VSX Unavailable
exception.
The VSX bit is added to the defined bits masks of the Power7 and
Power8 CPU models.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds the flag POWERPC_FLAG_VSX to the list of defined
flags and also adds this flag to the list of supported features of
the Power7 and Power8 CPUs. Additionally, the VSX instructions
are added to the list of TCG-enabled instruction.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Instead of opencoding 64 use MAX_SLB_ENTRIES. We don't update the kernel
header here.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
On POWER7, LPCR_ILE is used to control what endian guests take
their exceptions in so use it instead of MSR_ILE.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The savevm code for the powerpc cpu emulation is currently based around
the old register_savevm() rather than register_vmstate() method. It's also
rather broken, missing some important state on some CPU models.
This patch completely rewrites the savevm for target-ppc, using the new
VMStateDescription approach. Exactly what needs to be saved in what
configurations has been more carefully examined, too. This introduces a
new version (5) of the cpu save format. The old load function is retained
to support version 4 images.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-id: 1374175984-8930-2-git-send-email-aliguori@us.ibm.com
[aik: ppc cpu savevm convertion fixed to use PowerPCCPU instead of CPUPPCState]
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Where no extra implementation is needed, fall back to CPUClass::set_pc().
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Signed-off-by: Andreas Färber <afaerber@suse.de>
The functions cpu_clone_regs() and cpu_set_tls() are not purely CPU
related -- they are specific to the TLS ABI for a a particular OS.
Move them into the linux-user/ tree where they belong.
target-lm32 had entirely unused implementations, since it has no
linux-user target; just drop them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Use it to clean up the opcode table, resolving a former TODO from Jocelyn.
Also switch from malloc() to g_malloc().
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When running -cpu on a POWER7 system with PR KVM, we mask out the 1TB
MMU capability from the MMU type mask, but not the AMR bit.
This leads to us having a new MMU type that we don't check for in our
MMU management functions.
Add the new type, so that we don't have to worry about breakage there.
We're not going to use the TCG MMU management in that case anyway.
The long term fix for this will be to move all these MMU management
functions to class callbacks.
Signed-off-by: Alexander Graf <agraf@suse.de>
.. and enable it on POWER7 CPU.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
In addition to the performance monitor registers found on nearly all
6xx chips, the POWER7 has two additional counters (PMC5 & PMC6) and an
extra control register (MMCRA). This patch adds stub support for them to
qemu - the registers won't do anything, but with this change won't cause
illegal instruction traps accessing them. They're also registered with
their ONE_REG ids, so their value will be kept in sync with KVM where
appropriate.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This value is not needed if we use correctly the MSR[IP] bit.
excp_prefix is always 0x00000000, except when the MSR[IP] bit is
implemented and set to 1, in that case excp_prefix is 0xfff00000.
The handling of MSR[IP] was already implemented but not used at reset
because the value of env->msr was changed "manually".
The patch uses the function hreg_store_msr() to set env->msr, this
ensures a good handling of MSR[IP] at reset, and therefore a good value
for excp_prefix.
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
For softmmu builds the interface from the generic code to the target
specific MMU implementation is through the tlb_fill() function. For ppc
this is currently in mem_helper.c, whereas it would make more sense in
mmu_helper.c. This patch moves it, which also allows
cpu_ppc_handle_mmu_fault() to become a local function in mmu_helper.c
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
mmu_helper.c is, for obvious reasons, almost entirely concerned with
softmmu builds of qemu. However, it does contain one stub function which
is used when CONFIG_USER_ONLY=y - the user only versoin of
cpu_ppc_handle_mmu_fault, which always triggers an exception. The entire
rest of the file is surrounded by #if !defined(CONFIG_USER_ONLY).
We clean this up by moving the user only stub into its own new file,
removing the ifdefs and building mmu_helper.c only when CONFIG_SOFTMMU
is set. This also lets us remove the #define of cpu_handle_mmu_fault to
cpu_ppc_handle_mmu_fault - that name is only used from generic code for
user only - so we just name our split user version by the generic name.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Version 2.06 of the Power architecture describes an additional page
protection mechanism. Each virtual page has a "class" (0-31) recorded in
the PTE. The AMR register contains bits which can prohibit reads and/or
writes on a class by class basis. Interestingly, the AMR is userspace
readable and writable, however user mode writes are masked by the contents
of the UAMOR which is privileged.
This patch implements this protection mechanism, along with the AMR and
UAMOR SPRs. The architecture also specifies a hypervisor-privileged AMOR
register which masks user and supervisor writes to the AMR and UAMOR. We
leave this out for now, since we don't at present model hypervisor mode
correctly in any case.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[agraf: fix 32-bit hosts]
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently cpu.h contains a number of definitions relating to the 64-bit
hash MMU. Some are used in the MMU emulation code, but some are only used
in the spapr MMU management hcall implementations.
This patch moves these definitions (except for a few that are needed
more widely) into mmu-hash64.h header, shared between the MMU emulation
code and the spapr hcall code. The MMU emulation code is also updated to
actually use a number of those definitions in place of hard coded
constants.
Similarly, we add new analogous definitions to mmu-hash32.h and use those
in place of many hard-coded constants in mmu-hash32.c
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
[agraf: fix 32-bit hosts]
Signed-off-by: Alexander Graf <agraf@suse.de>
mmu_ctx_t is currently defined in cpu.h. However it is used for temporary
information relating to mmu translation, and is only used in mmu_helper.c
and (now) mmu-hash{32,64}.c. Furthermore it contains information which
should be specific to particular MMU types. Therefore, move its definition
to mmu_helper.c. mmu-hash{32,64}.c are converted to use new data types
private to the relevant MMUs (identical to mmu_ctx_t for now, but that will
change in future patches).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The functions for looking up BATs (Block Address Translation - essentially
a level 0 TLB) are shared between the classic 32-bit hash MMUs and the
6xx style software loaded TLB implementations.
This patch splits out a copy for the 32-bit hash MMUs, to facilitate
cleaning it up. The remaining version is left, but cleaned up slightly
to no longer deal with PowerPC 601 peculiarities (601 has a hash MMU).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The get_pteg_offset() helper function is currently shared between 32-bit
and 64-bit hash mmus, taking a parameter for the hash pte size. In the
64-bit paths, it's only called in one place, and it's a trivial
calculation. This patch, therefore, open codes it for 64-bit. The
remaining version, which is used in two places is made 32-bit only and
moved to mmu-hash32.c.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The newly separated paths for hash mmus rely on several helper functions
which are still shared with 32-bit hash mmus: pp_check(), check_prot() and
pte_update_flags(). While these don't have ugly ifdefs on the mmu type,
they're not very well thought out, so sharing them impedes cleaning up the
hash mmu paths. For now, put near-duplicate versions into mmu-hash64.c and
mmu-hash32.c, leaving the old version in mmu_helper.c for 6xx software
loaded tlb implementations. The hash 32 and software loaded
implementations are simplfied slightly, using the fact that no 32-bit CPUs
implement the 3rd page protection bit.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Depending on the MSR state, for 64-bit hash MMUs, get_physical_address
can either call check_physical (which has further tests for mmu type)
or get_segment64. Similarly for 32-bit hash MMUs we can either call
check_physucal or get_bat() and get_segment32().
This patch splits off the whole get_physical_addresss() path for hash
MMUs into 32-bit and 64-bit versions, handling real mode correctly for
such MMUs without going to check_physical and rechecking the mmu type.
Correspondingly, the hash MMU specific paths in check_physical() are
removed.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
32-bit and 64-bit hash MMU implementations currently share a find_pte
function. This results in a whole bunch of ugly conditionals in the shared
function, and not all that much actually shared code.
This patch separates out the 32-bit and 64-bit versions, putting then
in mmu-hash64.c and mmu-has32.c, and removes the conditionals from
both versions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently support for both 32-bit and 64-bit hash MMUs share an
implementation of pte_check. But there are enough differences that this
means the shared function has several very ugly conditionals on "is_64b".
This patch cleans things up by separating out the 64-bit version
(putting it into mmu-hash64.c) and the 32-bit hash version (putting it
in mmu-hash32.c). Another copy remains in mmu_helper.c, which is used
for the 6xx software loaded TLB paths.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
As a first step to disentangling the handling for 64-bit hash MMUs from
the rest, we move the code handling the Segment Lookaside Buffer (SLB)
(which only exists on 64-bit hash MMUs) into a new mmu-hash64.c file.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This removes the never-used pte64_invalidate() function, and makes
ppcmas_tlb_check() static, since it's only used within that file.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The PowerPC 620 was the very first 64-bit PowerPC implementation, but
hardly anyone ever actually used the chips. qemu notionally supports the
620, but since we don't actually have code to implement the segment table,
the support is broken (quite likely in other ways too).
This patch, therefore, removes all remaining pieces of 620 support, to
stop it cluttering up the platforms we actually care about. This includes
removing support for the ASR register, used only on segment table based
machines.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Although the support of this register may be uncomplete, there are no
reason to prevent the debugger from reading or writing it.
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This removes a global per-target function and thus takes us one step
closer to compiling multiple targets into one executable.
It will also allow to override the interrupt handling for certain CPU
families.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Both fields are used in VMState, thus need to be moved together.
Explicitly zero them on reset since they were located before
breakpoints.
Pass PowerPCCPU to kvmppc_handle_halt().
Signed-off-by: Andreas Färber <afaerber@suse.de>
Currently when runing under KVM on ppc, we synchronize a certain number of
vital SPRs to KVM through the SET_SREGS call. This leaves out quite a lot
of important SPRs which are maintained in KVM. It would be helpful to
have their contents in qemu for debugging purposes, and when we implement
migration it will be vital, since they include important guest state that
will need to be restored on the target.
This patch sets up for synchronization of any registers supported by the
KVM ONE_REG calls. A new variant on spr_register() allows a ONE_REG id to
be stored with the SPR information. When we set/get information to KVM
we also synchronize any SPRs so registered.
For now we set this mechanism up to synchronize a handful of important
registers that already have ONE_REG IDs, notably the DAR and DSISR.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Turn the array of model definitions into a set of self-registering QOM
types with their own class_init. Unique identifiers are obtained from
the combination of PVR, SVR and family identifiers; this requires all
alias #defines to be removed from the list. Possibly there are some more
left after this commit that are not currently being compiled.
Prepares for introducing abstract intermediate CPU types for families.
Keep the right-aligned macro line breaks within 78 chars to aid
three-way merges.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In preparation for more efficient setting of these fields.
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The bit that makes a dcbz instruction a dcbzl instruction was declared as
reserved in ppc32 ISAs. However, hardware simply ignores the bit, making
code valid if it simply invokes dcbzl instead of dcbz even on 750 and G4.
Thus, mark the bit as unreserved so that we properly emulate a simple dcbz
in case we're running on non-G5s.
While at it, also refactor the code to check the 970 special case during
runtime. This way we don't need to differenciate between a 970 dcbz and
any other dcbz anymore. We also allow for future improvements to add e500mc
dcbz handling.
Reported-by: Amadeusz Sławiński <amade@asmblr.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since the model list is highly macrofied, keep ppc_def_t for now and
save a pointer to it in PowerPCCPUClass. This results in a flat list of
subclasses including aliases, to be refined later.
Move cpu_ppc_init() to translate_init.c and drop helper.c.
Long-term the idea is to turn translate_init.c into a standalone cpu.c.
Inline cpu_ppc_usable() into type registration.
Split cpu_ppc_register() in two by code movement into the initfn and
by turning the remaining part into a realizefn.
Move qemu_init_vcpu() call into the new realizefn and adapt
create_ppc_opcodes() to return an Error.
Change ppc_find_by_pvr() -> ppc_cpu_class_by_pvr().
Change ppc_find_by_name() -> ppc_cpu_class_by_name().
Turn -cpu host into its own subclass. This requires to move the
kvm_enabled() check in ppc_cpu_class_by_name() to avoid the class being
found via the normal name lookup in the !kvm_enabled() case.
Turn kvmppc_host_cpu_def() into the class_init and add an initfn that
asserts KVM is in fact enabled.
Implement -cpu ? and the QMP equivalent in terms of subclasses.
This newly exposes -cpu host to the user, ordered last for -cpu ?.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We already used to support the external proxy facility of FSL MPICs,
but only implemented it halfway correctly.
This patch adds support for
* dynamic enablement of the EPR facility
* interrupt acknowledgement only when the interrupt is delivered
This way the implementation now is closer to real hardware.
Signed-off-by: Alexander Graf <agraf@suse.de>
The hwaddr type is somewhat vaguely defined as being able to contain bus
addresses on the widest possible bus in the system. For that reason it's
discouraged for representing specific pieces of persistent hardware state,
which should instead use an explicit width type that matches the bits
available in real hardware. In particular, because of the possibility that
the size of hwaddr might change if different buses are added to the target
in future, it's not suitable for use in vm state descriptions for savevm
and migration.
This patch purges such unwise uses of hwaddr from the ppc target code,
which turns out to be just one. The ppcemb_tlb_t struct, used on a number
of embedded ppc models to represent a TLB entry contains a hwaddr for the
real address field. This patch changes it to be a fixed uint64_t which is
suitable enough for all machine types which use this structure.
Other uses of hwaddr in CPUPPCState turn out not to be problematic:
htab_base and htab_mask are just used for the convenience of the TCG code;
the underlying machine state is the SDR1 register, which is stored with
a suitable type already. Likewise the mpic_cpu_base field is only used
internally and does not represent fundamental hardware state which needs to
be saved.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
* 'trivial-patches' of git://github.com/stefanha/qemu:
pc: Drop redundant test for ROM memory region
exec: make some functions static
target-ppc: make some functions static
ppc: add missing static
vnc: add missing static
vl.c: add missing static
target-sparc: make do_unaligned_access static
m68k: Return semihosting errno values correctly
cadence_uart: More debug information
Conflicts:
target-m68k/m68k-semi.c
This patch adds some extra FPU state to CPUPPCState. Specifically,
fpscr is extended to a target_ulong bits, since some recent (64 bit)
CPUs now have more status bits than fit inside 32 bits. Also, we add
the 32 VSR registers present on CPUs with VSX (these extend the
standard FP regs, which together with the Altivec/VMX registers form a
64 x 128bit register file for VSX).
We don't actually support the instructions using these extra registers
in TCG yet, but we still need a place to store the state so we can
sync it with KVM and savevm/loadvm it. This patch updates the savevm
code to not fail on the extended state, but also does not actually
save it - that's a project for another patch.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Stefan Hajnoczi
Eduardo Habkost
Cyril Bur
Aneesh Kumar K.V
Peter Maydell
Tom Musta
Paolo Bonzini
Bharata B Rao
Pierre Mallard
Richard Henderson
Greg Kurz
Alexey Kardashevskiy
Alexander Graf
Andreas Färber
Anton Blanchard
Aurelien Jarno
David Gibson
Fabien Chouteau
Blue Swirl
Anthony Liguori