gas/
* testsuite/gas/riscv/c-zero-imm.s: Test addi that compresses to c.nop.
* testsuite/gas/riscv/c-zero-imm.d: Likewise.
opcodes/
* riscv-opc.c (match_c_nop): New.
(riscv_opcodes) <addi>: Handle an addi that compresses to c.nop.
Just like their packed counterparts the memory operand is always 16
bytes wide, and the Disp8 scaling is the same for all of them. (As a
side note: I'm also surprised by there being AVX512VL variants of
these as well as the AVX512_4VNNIW ones - the SDM doesn't define any
such.)
Adjust the test cases also for the packed forms to actually live up to
their promise of testing correct Disp8 encoding.
gas/
* testsuite/gas/riscv/auipc-x0.d: New.
* testsuite/gas/riscv/auipc-x0.s: New.
opcodes/
* riscv-dis.c (maybe_print_address): If base_reg is zero,
then the hi_addr value is zero.
CSDB is a new instruction which Arm has defined. As it shares the
encoding space with NOP instructions, it is available from Armv3 in
Arm mode, and Armv6T2 in Thumb mode.
OK? If so, please commit on my behalf as I don't have commit rights
over here.
Thanks, James
---
opcodes/
2018-01-09 James Greenhalgh <james.greenhalgh@arm.com>
* arm-dis.c (arm_opcodes): Add csdb.
(thumb32_opcodes): Add csdb.
gas/
2018-01-09 James Greenhalgh <james.greenhalgh@arm.com>
* config/tc-arm.c (insns): Add csdb, enable for Armv3 and above
in Arm execution state, and Armv6T2 and above in Thumb execution
state.
* testsuite/gas/arm/csdb.s: New.
* testsuite/gas/arm/csdb.d: New.
* testsuite/gas/arm/thumb2_it_bad.l: Add csdb.
* testsuite/gas/arm/thumb2_it_bad.s: Add csdb.
CSDB is a new instruction which Arm has defined. It has the same encoding as
HINT #0x14 and is available at all architecture levels.
opcodes * aarch64-tbl.h (aarch64_opcode_table): Add "csdb".
* aarch64-asm-2.c: Regenerate.
* aarch64-dis-2.c: Regenerate.
* aarch64-opc-2.c: Regenerate.
gas * testsuite/gas/aarch64/system.d: Update expected results to expect
CSDB.
For historical reason, we allow movd/vmovd with 64-bit register and
memeory operands. But for vmovd, we failed to handle 64-bit memeory
operand. This has been gone unnoticed since AT&T syntax always treats
memory operand as 32-bit memory. This patch properly encodes vmovd
with 64-bit memeory operands. It also removes AVX512 vmovd with 64-bit
operands since GCC has
case TYPE_SSEMOV:
switch (get_attr_mode (insn))
{
case MODE_DI:
/* Handle broken assemblers that require movd instead of movq. */
if (!HAVE_AS_IX86_INTERUNIT_MOVQ
&& (GENERAL_REG_P (operands[0]) || GENERAL_REG_P (operands[1])))
return "%vmovd\t{%1, %0|%0, %1}";
return "%vmovq\t{%1, %0|%0, %1}";
and all AVX512 GNU assemblers set HAVE_AS_IX86_INTERUNIT_MOVQ, GCC won't
generate AVX512 vmovd with 64-bit operand.
gas/
PR gas/22681
* testsuite/gas/i386/i386.exp: Run x86-64-movd and
x86-64-movd-intel.
* testsuite/gas/i386/x86-64-movd-intel.d: New file.
* testsuite/gas/i386/x86-64-movd.d: Likewise.
* testsuite/gas/i386/x86-64-movd.s: Likewise.
opcodes/
PR gas/22681
* i386-opc.tbl: Properly encode vmovd with Qword memeory operand.
Remove AVX512 vmovd with 64-bit operands.
* i386-tbl.h: Regenerated.
Other than the variables in tc-i386.c using them, OPERAND_TYPE_REGYMM
and OPERAND_TYPE_REGZMM they aren't entirely unused. No need to update
i386-init.h though, as it mistakenly wasn't updated by the original
commit.
Dot products deviate from the normal disassembly rules for lane indexed
instruction. Their canonical representation is in the form of:
v0.2s, v0.8b, v0.4b[0] instead of v0.2s, v0.8b, v0.b[0] to try to denote
that these instructions select 4x 1 byte elements instead of a single 1 byte
element.
Previously we were disassembling them following the normal rules, this patch
corrects the disassembly.
gas/
PR gas/22559
* config/tc-aarch64.c (vectype_to_qualifier): Support AARCH64_OPND_QLF_S_4B.
* gas/testsuite/gas/aarch64/dotproduct.d: Update disassembly.
include/
PR gas/22559
* aarch64.h (aarch64_opnd_qualifier): Add AARCH64_OPND_QLF_S_4B.
opcodes/
PR gas/22559
* aarch64-asm.c (aarch64_ins_reglane): Change AARCH64_OPND_QLF_S_B to
AARCH64_OPND_QLF_S_4B
* aarch64-dis.c (aarch64_ext_reglane): Change AARCH64_OPND_QLF_S_B to
AARCH64_OPND_QLF_S_4B
* aarch64-opc.c (aarch64_opnd_qualifiers): Add 4b variant.
* aarch64-tbl.h (QL_V2DOT): Change S_B to S_4B.
Previously parse_vector_type_for_operand was changed to allow the use of 4b
register size for indexed lane instructions. However this had the unintended
side effect of also allowing 4b for normal vector registers.
Because this support was only partial the rest of the tool silently treated
4b as 8b and continued. This patch adds full support for 4b so it can be
properly distinguished from 8b and the correct errors are generated.
With this patch you still can't encode any instruction which actually requires
v<num>.4b but such instructions don't exist so to prevent needing a workaround
in get_vreg_qualifier_from_value this was just omitted.
gas/
PR gas/22529
* config/tc-aarch64.c (vectype_to_qualifier): Support AARCH64_OPND_QLF_V_4B.
* gas/testsuite/gas/aarch64/pr22529.s: New.
* gas/testsuite/gas/aarch64/pr22529.d: New.
* gas/testsuite/gas/aarch64/pr22529.l: New.
include/
PR gas/22529
* opcode/aarch64.h (aarch64_opnd_qualifier): Add AARCH64_OPND_QLF_V_4B.
opcodes/
PR gas/22529
* aarch64-opc.c (aarch64_opnd_qualifiers): Add 4b variant.
Just like for instructions in GPRs, there's no need to have separate
templates for otherwise identical insns acting on XMM or YMM registers
(or memory of the same size).
Use a combination of a single new Reg bit and Byte, Word, Dword, or
Qword instead.
Besides shrinking the number of operand type bits this has the benefit
of making register handling more similar to accumulator handling (a
generic flag is being accompanied by a "size qualifier"). It requires,
however, to split a few insn templates, as it is no longer correct to
have combinations like Reg32|Reg64|Byte. This slight growth in size will
hopefully be outweighed by this change paving the road for folding a
presumably much larger number of templates later on.
They are relevant only when multiple operands permit registers:
operand_type_register_match() returns true if either operand is not a
register one. IOW
grep -i CheckRegSize i386-opc.tbl | grep -Ev "(Reg[8136]|Acc).*,.*(Reg|Acc)"
should produce no output.
opcodes * disassemble.c: Enable disassembler_needs_relocs for PRU.
gas * testsuite/gas/pru/extern.s: New test for print of U16_PMEMM
relocation.
* testsuite/gas/pru/extern.d: New test driver.
When checking mapping symbols backwardly, the section which defines the symbol
is not considerted. This patch fixes this by moving the section checking code
into get_sym_code_type () function which is shared by forward and backword
mapping symbol searching.
opcodes/
2017-12-11 Petr Pavlu <petr.pavlu@arm.com>
Renlin Li <renlin.li@arm.com>
* aarch64-dis.c (print_insn_aarch64): Move symbol section check ...
(get_sym_code_type): Here.
binutils/
2017-12-11 Renlin Li <renlin.li@arm.com>
* testsuite/binutils-all/aarch64/objdump.d: New.
* testsuite/binutils-all/aarch64/objdump.s: New.
BaseIndex implies - with the exception of string instructions the
optional presence of a displacement. This is almost completely uniform
for all instructions (the sole exception being MPX ones, which don't
allow 16-bit addressing and hence Disp16), so there's no point in
explicitly stating this in the main opcode table. Drop those explict
specifications in favor of adding logic to i386-gen, shrinking the
table size quite a bit and hence making it more readable.
The opcodes/i386-tbl.h changes are due to a few cases where pointless
Disp* still hadn't been removed from their insns.
bfd/
* po/Make-in (datadir): Define as @datadir@.
(localedir): Define as @localedir@.
(gnulocaledir, gettextsrcdir): Use @datarootdir@.
binutils/
* po/Make-in (datadir): Define as @datadir@.
(localedir): Define as @localedir@.
(gnulocaledir, gettextsrcdir): Use @datarootdir@.
gas/
* po/Make-in (datadir): Define as @datadir@.
(localedir): Define as @localedir@.
(gnulocaledir, gettextsrcdir): Use @datarootdir@.
gold/
* po/Make-in (datadir): Define as @datadir@.
(localedir): Define as @localedir@.
(gnulocaledir, gettextsrcdir): Use @datarootdir@.
gprof/
* po/Make-in (datadir): Define as @datadir@.
(localedir): Define as @localedir@.
(gnulocaledir, gettextsrcdir): Use @datarootdir@.
ld/
* po/Make-in (datadir): Define as @datadir@.
(localedir): Define as @localedir@.
(gnulocaledir, gettextsrcdir): Use @datarootdir@.
opcodes/
* po/Make-in (datadir): Define as @datadir@.
(localedir): Define as @localedir@.
(gnulocaledir, gettextsrcdir): Use @datarootdir@.
Despite EVEX encodings not being available in real and VM86 modes,
16-bit addressing still needs to be handled properly for 16-bit
protected mode as well as 16-bit addressing in 32-bit mode. Neither
should displacements be dropped silently by the assembler, nor should
the disassembler fail to correctly scale 8-bit displacements.
Make the assembler recognize UD0, supporting only the newer form
expecting a ModR/M byte.
Make assembler and disassembler properly emit / expect a ModR/M byte for
UD1.
For the testsuite, as arch-4 already tests all UDn, avoid producing a
huge delta for other tests using UD2B by making them use UD2 instead.
This patch separates the new FP16 instructions backported from Armv8.4-a to Armv8.2-a
into a new flag order to distinguish them from the rest of the already existing optional
FP16 instructions in Armv8.2-a.
The new flag "+fp16fml" is available from Armv8.2-a and implies +fp16 and is mandatory on
Armv8.4-a.
gas/
* config/tc-aarch64.c (fp16fml): New.
* doc/c-aarch64.texi (fp16fml): New.
* testsuite/gas/aarch64/armv8_2-a-crypto-fp16.d (fp16): Make fp16fml.
* testsuite/gas/aarch64/armv8_3-a-crypto-fp16.d (fp16): Make fp16fml.
include/
* opcode/aarch64.h: (AARCH64_FEATURE_F16_FML): New.
(AARCH64_ARCH_V8_4): Enable AARCH64_FEATURE_F16_FML by default.
opcodes/
* aarch64-tbl.h (aarch64_feature_fp_16_v8_2): Require AARCH64_FEATURE_F16_FML
and AARCH64_FEATURE_F16.
While commits 9889cbb14e ("Check invalid mask registers") and
abfcb414b9 ("X86: Ignore REX_B bit for 32-bit XOP instructions") went a
bit into the right direction, this wasn't quite enough:
- VEX.vvvv has its high bit ignored
- EVEX.vvvv has its high bit ignored together with EVEX.v'
- the high bits of {,E}VEX.vvvv should not be prematurely zapped, to
allow proper checking of them when the fields has to hold al ones
- when the high bits of an immediate specify a register, bit 7 is
ignored
VEX.W may be legitimately set (and is then ignored by the CPU) for
non-64-bit code. Don't print 64-bit register names in such a case, by
utilizing that REX_W would never be set for non-64-bit code, and that
it is being set from VEX.W by generic decoding.
A test for this is going to be introduced in the next patch of this
series.
The low four bits of an immediate being set when the high bits specify a
fourth register operand is not a problem: CPUs ignore these bits rather
than raising #UD. Take care of incrementing codep in OP_EX_VexW()
instead.
Just like %cxl can't be used as shift count register. Otherwise for
consistency %cxl would need to gain "ShiftCount" and use of both ought
to properly cause REX prefixes to be emitted.
