This patch removes use of st_target_internal to cache the result of
comparing symbol names against CMSE_PREFIX. The problem with setting
a bit in st_target_internal in swap_symbol_in is that calling
bfd_elf_sym_name from swap_symbol_in requires symtab_hdr, and you
don't know for sure whether swap_symbol_in is operating on dynsyms
(and thus elf_tdata (abfd)->dynsymtab_hdr should be used) or on the
normal symtab (thus elf_tdata (abfd)->symtab_hdr). You can make an
educated guess based on abfd->flags & DYNAMIC but that relies on
knowing a lot about calls to bfd_elf_get_elf_syms, and is fragile in
the face of possible future changes.
include/
* elf/arm.h (ARM_GET_SYM_CMSE_SPCL, ARM_SET_SYM_CMSE_SPCL): Delete.
bfd/
* elf32-arm.c (cmse_scan): Don't use ARM_GET_SYM_CMSE_SPCL,
instead recognize CMSE_PREFIX in symbol name.
(elf32_arm_gc_mark_extra_sections): Likewise.
(elf32_arm_filter_cmse_symbols): Don't test ARM_GET_SYM_CMSE_SPCL.
(elf32_arm_swap_symbol_in): Don't invoke ARM_SET_SYM_CMSE_SPCL.
This patch is a reimplementation of [1] which was submitted in 2015 by
Neil Schellenberger. Copyright issue was sorted out [2] last year.
It proposed a new section (.gnu.xhash) and related dynamic tag
(DT_GNU_XHASH). The new section would be virtually identical to the
existing .gnu.hash except for the translation table (xlat) which would
contain correct MIPS .dynsym indexes corresponding to the hashvals in
chains. This is because MIPS ABI imposes a different ordering on the
dynsyms than the one expected by the .gnu.hash section. Another addition
would be a leading word (ngnusyms) which would contain the number of
entries in the translation table.
In this patch, the new section name and dynamic tag are changed to
reflect the fact that the section should be treated as MIPS-specific
(.MIPS.xhash and DT_MIPS_XHASH).
This patch addresses the alignment issue as reported in [3], which is
caused by the leading word added to the .MIPS.xhash section. Leading word
is removed in this patch, and the number of entries in the translation
table is now calculated using DT_MIPS_SYMTABNO dynamic tag (this is
addressed by the corresponding glibc patch).
Suggestions on coding style in [4] were taken into account. Existing
GNU hash testcase was covered, and another one was added in the MIPS
part of the testsuite.
The other major change is reserving MIPS ABI version 5 for .MIPS.xhash,
marking the need of support for .MIPS.xhash in the dynamic linker (again,
addressed in the corresponding glibc patch). This is something which I
am not sure of, especially after reading [5]. I am confused on whether
this ABI version is reserved for IFUNC, or it can be used for this
purpose.
Already mentioned glibc patch is submitted at:
https://sourceware.org/ml/libc-alpha/2019-06/msg00456.html
[1] https://sourceware.org/ml/binutils/2015-10/msg00057.html
[2] https://sourceware.org/ml/binutils/2018-03/msg00025.html
[3] https://sourceware.org/ml/binutils/2016-01/msg00006.html
[4] https://sourceware.org/ml/binutils/2016-02/msg00097.html
[5] https://sourceware.org/ml/libc-alpha/2016-12/msg00853.html
ld * emulparams/elf32bmip.sh: Add .MIPS.xhash section.
* emulparams/elf32bmipn32-defs.sh: Add .MIPS.xhash section.
* emulparams/elf64bmip-defs.sh: Add .MIPS.xhash section.
* emultempl/mipself.em: Remove mips_after_parse function.
* testsuite/ld-elf/hash.d: Update comment.
* testsuite/ld-mips-elf/hash1.d: New test.
* testsuite/ld-mips-elf/hash1.s: Ditto.
* testsuite/ld-mips-elf/hash1a.d: Remove.
* testsuite/ld-mips-elf/hash1b.d: Ditto.
* testsuite/ld-mips-elf/hash1c.d: Ditto
* testsuite/ld-mips-elf/hash2.d: New test.
* testsuite/ld-mips-elf/mips-elf.exp: New tests.
* testsuite/ld-mips-elf/start.s: New test.
bfd * elf-bfd.h (struct elf_backend_data): New members.
* elflink.c (_bfd_elf_link_create_dynamic_sections): Create
.gnu.hash section if necessary.
(struct collect_gnu_hash_codes): New member.
(elf_gnu_hash_process_symidx): New function name.
(elf_renumber_gnu_hash_syms): Ignore local and undefined
symbols. Record xlat location for every symbol which should have
a .MIPS.xhash entry.
(bfd_elf_size_dynamic_sections): Add DT_GNU_HASH dynamic tag to
dynamic section if necessary.
(GNU_HASH_SECTION_NAME): New define.
(bfd_elf_size_dynsym_hash_dynstr): Get .MIPS.xhash section.
Update the section size info.
* elfxx-mips.c (struct mips_elf_hash_sort_data): New members.
(struct mips_elf_link_hash_entry): New member.
(mips_elf_link_hash_newfunc): Initialize .MIPS.xhash translation
table location.
(mips_elf_sort_hash_table): Initialize the pointer to the
.MIPS.xhash section.
(mips_elf_sort_hash_table_f): Populate the .MIPS.xhash
translation table entry with the symbol dynindx.
(_bfd_mips_elf_section_from_shdr): Add SHT_MIPS_XHASH.
(_bfd_mips_elf_fake_sections): Initialize .MIPS.xhash section
info.
(_bfd_mips_elf_create_dynamic_sections): Create .MIPS.xhash
section.
(_bfd_mips_elf_size_dynamic_sections): Add DT_MIPS_XHASH tag to
dynamic section.
(_bfd_mips_elf_finish_synamic_sections): Add DT_MIPS_XHASH.
(_bfd_mips_elf_final_write_processing): Set .MIPS.xhash section
sh_link info.
(_bfd_mips_elf_get_target_dtag): Get DT_MIPS_XHASH tag.
(MIPS_LIBC_ABI_XHASH): New ABI version enum value.
(_bfd_mips_post_process_headers): Mark the ABI version as
MIPS_LIBC_ABI_XHASH if there exists a .MIPS.xhash section,
but not a .hash section.
(_bfd_mips_elf_record_xhash_symbol): New function. Record a
position in the translation table, associated with the hash
entry.
* elfxx-mips.h (literal_reloc_p): Define
elf_backend_record_xhash_symbol backend hook.
* elfxx-target.h: Initialize elf_backend_record_xhash_symbol
backend hook.
include * elf/mips.h (SHT_GNU_XHASH): New define.
(DT_GNU_XHASH): New define.
binutils * readelf.c (get_mips_dynamic_type): Return MIPS_XHASH dynamic type.
(get_mips_section_type_name): Return MI{S_XHASH name string.
(dynamic_section_mips_val): Initialize the .MIPS.xhash dynamic
info.
(process_symbol_table): Initialize the .MIPS.xhash section
pointer. Adjust the readelf output to support the new section.
(process_object): Set the .MIPS.xhash dynamic info to zero.
This patch supports using pcrel instructions in TLS code sequences. A
number of new relocations are needed, gas operand modifiers to
generate those relocations, and new TLS optimisation. For
optimisation it turns out that the new pcrel GD and LD sequences can
be distinguished from the non-pcrel GD and LD sequences by there being
different relocations on the new sequence. The final "add ra,rb,13"
on IE sequences similarly needs a new relocation, or as I chose, a
modification of R_PPC64_TLS. On pcrel IE code, the R_PPC64_TLS points
one byte into the "add" instruction rather than being on the
instruction boundary.
GD:
pla 3,z@got@tlsgd@pcrel # R_PPC64_GOT_TLSGD34
bl __tls_get_addr@notoc(z@tlsgd) # R_PPC64_TLSGD and R_PPC64_REL24_NOTOC
edited to IE
pld 3,z@got@tprel@pcrel
add 3,3,13
edited to LE
paddi 3,13,z@tprel
nop
LD:
pla 3,z@got@tlsld@pcrel # R_PPC64_GOT_TLSLD34
bl __tls_get_addr@notoc(z@tlsld) # R_PPC64_TLSLD and R_PPC64_REL24_NOTOC
..
paddi 9,3,z2@dtprel
pld 10,z3@got@dtprel@pcrel
add 10,10,3
edited to LE
paddi 3,13,0x1000
nop
IE:
pld 9,z@got@tprel@pcrel # R_PPC64_GOT_TPREL34
add 3,9,z@tls@pcrel # R_PPC64_TLS at insn+1
ldx 4,9,z@tls@pcrel
lwax 5,9,z@tls@pcrel
stdx 5,9,z@tls@pcrel
edited to LE
paddi 9,13,z@tprel
nop
ld 4,0(9)
lwa 5,0(9)
std 5,0(9)
LE:
paddi 10,13,z@tprel
include/
* elf/ppc64.h (R_PPC64_TPREL34, R_PPC64_DTPREL34),
(R_PPC64_GOT_TLSGD34, R_PPC64_GOT_TLSLD34),
(R_PPC64_GOT_TPREL34, R_PPC64_GOT_DTPREL34): Define.
(IS_PPC64_TLS_RELOC): Include new tls relocs.
bfd/
* reloc.c (BFD_RELOC_PPC64_TPREL34, BFD_RELOC_PPC64_DTPREL34),
(BFD_RELOC_PPC64_GOT_TLSGD34, BFD_RELOC_PPC64_GOT_TLSLD34),
(BFD_RELOC_PPC64_GOT_TPREL34, BFD_RELOC_PPC64_GOT_DTPREL34),
(BFD_RELOC_PPC64_TLS_PCREL): New pcrel tls relocs.
* elf64-ppc.c (ppc64_elf_howto_raw): Add howtos for pcrel tls relocs.
(ppc64_elf_reloc_type_lookup): Translate pcrel tls relocs.
(must_be_dyn_reloc, dec_dynrel_count): Add R_PPC64_TPREL64.
(ppc64_elf_check_relocs): Support pcrel tls relocs.
(ppc64_elf_tls_optimize, ppc64_elf_relocate_section): Likewise.
* bfd-in2.h: Regenerate.
* libbfd.h: Regenerate.
gas/
* config/tc-ppc.c (ppc_elf_suffix): Map "tls@pcrel", "got@tlsgd@pcrel",
"got@tlsld@pcrel", "got@tprel@pcrel", and "got@dtprel@pcrel".
(fixup_size, md_assemble): Handle pcrel tls relocs.
(ppc_force_relocation, ppc_fix_adjustable): Likewise.
(md_apply_fix, tc_gen_reloc): Likewise.
ld/
* testsuite/ld-powerpc/tlsgd.d,
* testsuite/ld-powerpc/tlsgd.s,
* testsuite/ld-powerpc/tlsie.d,
* testsuite/ld-powerpc/tlsie.s,
* testsuite/ld-powerpc/tlsld.d,
* testsuite/ld-powerpc/tlsld.s: New tests.
* testsuite/ld-powerpc/powerpc.exp: Run them.
These ilp32 relocations were missing for some reason.
bfd/ChangeLog:
* elfnn-aarch64.c: Enable MOVW_PREL relocs for ELF32.
include/ChangeLog:
* elf/aarch64.h (R_AARCH64_P32_MOVW_PREL_G0): Define.
(R_AARCH64_P32_MOVW_PREL_G0_NC): Define.
(R_AARCH64_P32_MOVW_PREL_G1): Define.
ld/ChangeLog:
* testsuite/ld-aarch64/aarch64-elf.exp: Add emit-relocs-22 and -23.
* testsuite/ld-aarch64/emit-relocs-22.d: New test.
* testsuite/ld-aarch64/emit-relocs-22.s: New test.
* testsuite/ld-aarch64/emit-relocs-23.d: New test.
* testsuite/ld-aarch64/emit-relocs-23.s: New test.
The bottom 2 bits of st_other are used for visibility, the top 6 bits are
de facto reserved for processor specific use. This patch defines a
bits to mark function symbols that follow a variant procedure call standard
with different register usage convention.
A dynamic tag is also defined that marks modules with R_<CLS>_JUMP_SLOT
relocations referencing symbols marked with STO_AARCH64_VARIANT_PCS.
This can be used by dynamic linkers that support lazy binding to decide
what registers need to be preserved during symbol resolution.
binutils/ChangeLog:
* readelf.c (get_aarch64_dynamic_type): Handle DT_AARCH64_VARIANT_PCS.
(get_aarch64_symbol_other): New, handles STO_AARCH64_VARIANT_PCS.
(get_symbol_other): Call get_aarch64_symbol_other.
include/ChangeLog:
* elf/aarch64.h (DT_AARCH64_VARIANT_PCS): Define.
(STO_AARCH64_VARIANT_PCS): Define.
This patch adds a header file with BPF-specific ELF definitions. In
particular, the architecture relocations.
include/ChangeLog:
2019-05-23 Jose E. Marchesi <jose.marchesi@oracle.com>
* elf/bpf.h: New file.
bfd/ChangeLog:
2019-05-16 Andre Vieira <andre.simoesdiasvieira@arm.com>
* elf32-arm.c (elf32_arm_merge_eabi_attributes): Add case for Tag_MVE_arch.
binutils/ChangeLog:
2019-05-16 Andre Vieira <andre.simoesdiasvieira@arm.com>
* readelf.c (arm_attr_tag_MVE_arch): New array for Tag_MVE_arch values.
(arm_attr_public_tag arm_attr_public_tags): Add case for Tag_MVE_arch.
elfcpp/ChangeLog:
2019-05-16 Andre Vieira <andre.simoesdiasvieira@arm.com>
* arm.h (Tag_MVE_arch): Define new enum value.
gas/ChangeLog:
2019-05-16 Andre Vieira <andre.simoesdiasvieira@arm.com>
* config/tc-arm.c (mve_ext, mve_fp_ext): New features.
(armv8_1m_main_ext_table): Add new extensions.
(aeabi_set_public_attributes): Translate new features to new build attributes.
(arm_convert_symbolic_attribute): Add Tag_MVE_arch.
* doc/c-arm.texi: Document new extensions and new build attribute.
include/ChangeLog:
2019-05-16 Andre Vieira <andre.simoesdiasvieira@arm.com>
* elf/arm.h (Tag_MVE_arch): Define new enum value.
* opcode/arm.h (FPU_MVE, FPU_MVE_FP): New MACROs for new features.
This patch is part of a series of patches to add support for Armv8.1-M Mainline
instructions to binutils.
This adds infrastructure for the BFCSEL instructions which is one of the first
instructions in Arm that have more than one relocations in them.
This adds a new relocation R_ARM_THM_BF12.
The inconsistency between external R_ARM_THM_BF12 and internal
BFD_RELOC_ARM_THUMB_BF13 is because internally we count the static bit-0 of the
immediate and we don't externally.
ChangeLog entries are as follows :
ChangeLog entries are as follows :
*** bfd/ChnageLog ***
2019-04-04 Sudakshina Das <sudi.das@arm.com>
* reloc.c (BFD_RELOC_ARM_THUMB_BF13): New.
* bfd-in2.h: Regenerated.
* libbfd.h: Regenerated.
* elf32-arm.c (elf32_arm_howto_table_1): New entry for R_ARM_THM_BF13.
(elf32_arm_reloc_map elf32_arm_reloc_map): Map BFD_RELOC_ARM_THUMB_BF13
and R_ARM_THM_BF12 together.
(elf32_arm_final_link_relocate): New switch case for R_ARM_THM_BF13.
*** elfcpp/ChangeLog ***
2019-04-04 Sudakshina Das <sudi.das@arm.com>
* arm.h (R_ARM_THM_BF12): New relocation code.
*** gas/ChangeLog ***
2019-04-04 Sudakshina Das <sudi.das@arm.com>
* config/tc-arm.c (md_pcrel_from_section): New switch case for
BFD_RELOC_ARM_THUMB_BF13.
(md_appdy_fix): Likewise.
(tc_gen_reloc): Likewise.
*** include/ChangeLog ***
2019-04-04 Sudakshina Das <sudi.das@arm.com>
* elf/arm.h (START_RELOC_NUMBERS): New entry for R_ARM_THM_BF12.
*** opcodes/ChangeLog ***
2019-04-04 Sudakshina Das <sudi.das@arm.com>
* arm-dis.c (print_insn_thumb32): Updated to accept new %Z pattern.
This patch is part of a series of patches to add support for Armv8.1-M Mainline instructions to binutils.
This adds infrastructure for the BFL instructions which is one of the first instructions in Arm that have more than one relocations in them.
This adds a new relocation R_ARM_THM_BF18.
The inconsistency between external R_ARM_THM_BF18 and internal
BFD_RELOC_ARM_THUMB_BF19 is because internally we count the static bit-0 of the immediate and we don't externally.
ChangeLog entries are as follows :
*** bfd/ChangeLog ***
2019-04-15 Sudakshina Das <sudi.das@arm.com>
* reloc.c (BFD_RELOC_ARM_THUMB_BF19): New
* libbfd.h: Regenerated.
* bfd-in2.h: Regenerated.
* bfd-elf32-arm.c (elf32_arm_howto_table_1): New entry for R_ARM_THM_BF18.
(elf32_arm_reloc_map elf32_arm_reloc_map): Map BFD_RELOC_ARM_THUMB_BF19
and R_ARM_THM_BF18 together.
(elf32_arm_final_link_relocate): New switch case for R_ARM_THM_BF19.
*** elfcpp/ChangeLog ***
2019-04-15 Sudakshina Das <sudi.das@arm.com>
* arm.h (R_ARM_THM_BF18): New relocation code.
*** gas/ChangeLog ***
2019-04-15 Sudakshina Das <sudi.das@arm.com>
* config/tc-arm.c (md_pcrel_from_section): New switch case for
BFD_RELOC_ARM_THUMB_BF19.
(md_appdy_fix): Likewise.
(tc_gen_reloc): Likewise.
*** include/ChangeLog ***
2019-04-15 Sudakshina Das <sudi.das@arm.com>
* elf/arm.h (START_RELOC_NUMBERS): New entry for R_ARM_THM_BF18.
*** opcodes/ChangeLog ***
2019-04-15 Sudakshina Das <sudi.das@arm.com>
* arm-dis.c (print_insn_thumb32): Updated to accept new %Y pattern.
This patch is part of a series of patches to add support for Armv8.1-M Mainline instructions to binutils.
This adds infrastructure for the BF instructions which is one of the first instructions in Arm that have more than one relocations in them.
This is the third infrastructure patch that adds a new relocation R_ARM_THM_BF16.
The inconsistency between external R_ARM_THM_BF16 and internal
BFD_RELOC_ARM_THUMB_BF17 is because internally we count the static bit-0 of the immediate and we don't externally.
ChangeLog entries are as follows :
*** bfd/ChangeLog ***
2019-04-15 Sudakshina Das <sudi.das@arm.com>
* reloc.c (BFD_RELOC_ARM_THUMB_BF17): New enum.
* bfd-in2.h: Regenerated.
* libbfd.h: Regenerated.
* bfd-elf32-arm.c (elf32_arm_howto_table_1): New entry for R_ARM_THM_BF16.
(elf32_arm_reloc_map elf32_arm_reloc_map): Map BFD_RELOC_ARM_THUMB_BF17
and R_ARM_THM_BF16 together.
(get_value_helper): New reloc helper.
(elf32_arm_final_link_relocate): New switch case for R_ARM_THM_BF16.
*** elfcpp/ChangeLog ***
2019-04-15 Sudakshina Das <sudi.das@arm.com>
* arm.h (R_ARM_THM_BF16): New relocation code.
*** gas/ChangeLog ***
2019-04-15 Sudakshina Das <sudi.das@arm.com>
* config/tc-arm.c (md_pcrel_from_section): New switch case for
BFD_RELOC_ARM_THUMB_BF17.
(md_appdy_fix): Likewise.
(tc_gen_reloc): Likewise.
*** include/ChangeLog ***
2019-04-15 Sudakshina Das <sudi.das@arm.com>
* elf/arm.h (START_RELOC_NUMBERS): New entry for R_ARM_THM_BF16.
*** opcodes/ChangeLog ***
2019-04-15 Sudakshina Das <sudi.das@arm.com>
* arm-dis.c (print_insn_thumb32): Updated to accept new %W pattern.
The patch is straightforward, it does the following:
- support the new Tag_CPU_arch build attribute value, ie.:
+ declare the new value
+ update all the asserts forcing logic to be reviewed for new
architectures
+ create a corresponding bfd_mach_arm_8_1M_MAIN enumerator in bfd and
add mapping from Tag_CPU_arch to it
+ teach readelf about new Tag_CPU_arch value
- declare armv8.1-m.main as a supported architecture value
- define Armv8.1-M Mainline in terms of feature bits available
- tell objdump mapping from bfd_mach_arm_8_1M_MAIN enumerator to feature
bits available
- update architecture-specific logic in gas and bfd guarded by the
asserts mentioned above.
- tests for all the above
ChangeLog entries are as follows:
*** bfd/ChangeLog ***
2019-04-15 Thomas Preud'homme <thomas.preudhomme@arm.com>
* archures.c (bfd_mach_arm_8_1M_MAIN): Define.
* bfd-in2.h: Regenerate.
* cpu-arm.c (arch_info_struct): Add entry for Armv8.1-M Mainline.
* elf32-arm.c (using_thumb_only): Return true for Armv8.1-M Mainline
and update assert.
(using_thumb2): Likewise.
(using_thumb2_bl): Update assert.
(arch_has_arm_nop): Likewise.
(bfd_arm_get_mach_from_attributes): Add case for Armv8.1-M Mainline.
(tag_cpu_arch_combine): Add logic for Armv8.1-M Mainline merging.
*** binutils/ChangeLog ***
2019-04-15 Thomas Preud'homme <thomas.preudhomme@arm.com>
* readelf.c (arm_attr_tag_CPU_arch): Add entry for Armv8.1-M Mainline.
*** gas/ChangeLog ***
2019-04-15 Thomas Preud'homme <thomas.preudhomme@arm.com>
* config/tc-arm.c (cpu_arch_ver): Add entry for Armv8.1-M Mainline
Tag_CPU_arch build attribute value. Reindent.
(get_aeabi_cpu_arch_from_fset): Update assert.
(aeabi_set_public_attributes): Update assert for Tag_DIV_use logic.
* testsuite/gas/arm/attr-march-armv8_1-m.main.d: New test.
*** include/ChangeLog ***
2019-04-15 Thomas Preud'homme <thomas.preudhomme@arm.com>
* elf/arm.h (TAG_CPU_ARCH_V8_1M_MAIN): new macro.
(MAX_TAG_CPU_ARCH): Set value to above macro.
* opcode/arm.h (ARM_EXT2_V8_1M_MAIN): New macro.
(ARM_AEXT_V8_1M_MAIN): Likewise.
(ARM_AEXT2_V8_1M_MAIN): Likewise.
(ARM_ARCH_V8_1M_MAIN): Likewise.
*** ld/ChangeLog ***
2019-04-15 Thomas Preud'homme <thomas.preudhomme@arm.com>
* testsuite/ld-arm/attr-merge-13.attr: New test.
* testsuite/ld-arm/attr-merge-13a.s: New test.
* testsuite/ld-arm/attr-merge-13b.s: New test.
*** opcodes/ChangeLog ***
2019-04-15 Thomas Preud'homme <thomas.preudhomme@arm.com>
* arm-dis.c (select_arm_features): Add logic for Armv8.1-M Mainline.
This is part of the patch series to add support for BTI and
PAC in AArch64 linker.
1) This patch adds new definitions of PAC enabled PLTs
and both BTI and PAC enabled PLTs.
2) It also defines the new dynamic tag DT_AARCH64_PAC_PLT
for the PAC enabled PLTs.
3) This patch adds a new ld command line option: --pac-plt.
In the presence of this option, the linker uses the PAC
enabled PLTs and marks with DT_AARCH64_PAC_PLT.
4) In case both BTI and PAC are enabled the linker should
pick PLTs enabled with both and also use dynamic tags for both.
All these are made according to the new AArch64 ELF ABI
https://developer.arm.com/docs/ihi0056/latest/elf-for-the-arm-64-bit-architecture-aarch64-abi-2018q4
*** bfd/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
* elfnn-aarch64.c (PLT_PAC_ENTRY_SIZE, PLT_PAC_SMALL_ENTRY_SIZE): New.
(PLT_BTI_PAC_ENTRY_SIZE, PLT_BTI_PAC_SMALL_ENTRY_SIZE): New.
(setup_plt_values): Account for PAC or PAC and BTI enabled PLTs.
(elfNN_aarch64_size_dynamic_sections): Add checks for PLT_BTI_PAC
and PLT_PAC_PLT.
(elfNN_aarch64_finish_dynamic_sections): Account for PLT_BTI_PAC.
(get_plt_type): Add case for DT_AARCH64_PAC_PLT.
(elfNN_aarch64_plt_sym_val): Add cases for PLT_BTI_PAC and PLT_PAC.
*** binutils/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
* readelf.c (get_aarch64_dynamic_type): Add case for
DT_AARCH64_PAC_PLT.
(dynamic_section_aarch64_val): Likewise.
*** include/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
* elf/aarch64.h (DT_AARCH64_PAC_PLT): New.
*** ld/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
* NEWS: Document --pac-plt.
* emultempl/aarch64elf.em (OPTION_PAC_PLT): New.
(PARSE_AND_LIST_LONGOPTS, PARSE_AND_LIST_OPTIONS): Add pac-plt.
(PARSE_AND_LIST_ARGS_CASES): Handle OPTION_PAC_PLT.
* testsuite/ld-aarch64/aarch64-elf.exp: Add the following tests.
* testsuite/ld-aarch64/bti-pac-plt-1.d: New test.
* testsuite/ld-aarch64/bti-pac-plt-2.d: New test.
* testsuite/ld-aarch64/pac-plt-1.d: New test.
* testsuite/ld-aarch64/pac-plt-2.d: New test.
* testsuite/ld-aarch64/bti-plt-1.s: Add .ifndef directive.
This is part of the patch series to add support for BTI and
PAC in AArch64 linker.
1) This patch adds a new ld command line option: --force-bti.
In the presence of this option, the linker enables BTI with the
GNU_PROPERTY_AARCH64_FEATURE_1_BTI feature. This gives out warning
in case of missing gnu notes for BTI in inputs.
2) It also defines a new set of BTI enabled PLTs. These are used either
when all the inputs are marked with GNU_PROPERTY_AARCH64_FEATURE_1_BTI
or when the new --force-bti option is used. This required adding new
fields in elf_aarch64_link_hash_table so that we could make the PLT
related information more generic.
3) It also defines a dynamic tag DT_AARCH64_BTI_PLT. The linker uses
this whenever it picks BTI enabled PLTs.
All these are made according to the new AArch64 ELF ABI
https://developer.arm.com/docs/ihi0056/latest/elf-for-the-arm-64-bit-architecture-aarch64-abi-2018q4
*** bfd/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
Szabolcs Nagy <szabolcs.nagy@arm.com>
* bfd-in.h (aarch64_plt_type, aarch64_enable_bti_type): New.
(aarch64_bti_pac_info): New.
(bfd_elf64_aarch64_set_options): Add aarch64_bti_pac_info argument.
(bfd_elf32_aarch64_set_options): Likewise.
* bfd-in2.h: Regenerate
* elfnn-aarch64.c (PLT_BTI_ENTRY_SIZE): New.
(PLT_BTI_SMALL_ENTRY_SIZE, PLT_BTI_TLSDESC_ENTRY_SIZE): New.
(elfNN_aarch64_small_plt0_bti_entry): New.
(elfNN_aarch64_small_plt_bti_entry): New.
(elfNN_aarch64_tlsdesc_small_plt_bti_entry): New.
(elf_aarch64_obj_tdata): Add no_bti_warn and plt_type fields.
(elf_aarch64_link_hash_table): Add plt0_entry, plt_entry and
tlsdesc_plt_entry_size fields.
(elfNN_aarch64_link_hash_table_create): Initialise the new fields.
(setup_plt_values): New helper function.
(bfd_elfNN_aarch64_set_options): Use new bp_info to set plt sizes and
bti enable type.
(elfNN_aarch64_allocate_dynrelocs): Use new size members instead of
fixed macros.
(elfNN_aarch64_size_dynamic_sections): Likewise and add checks.
(elfNN_aarch64_create_small_pltn_entry): Use new generic pointers
to plt stubs instead of fixed ones and update filling them according
to the need for bti.
(elfNN_aarch64_init_small_plt0_entry): Likewise.
(elfNN_aarch64_finish_dynamic_sections): Likewise.
(get_plt_type, elfNN_aarch64_get_synthetic_symtab): New.
(elfNN_aarch64_plt_sym_val): Update size accordingly.
(elfNN_aarch64_link_setup_gnu_properties): Set up plts if BTI GNU NOTE
is set.
(bfd_elfNN_get_synthetic_symtab): Define.
(elfNN_aarch64_merge_gnu_properties): Give out warning with --force-bti
and mising BTI NOTE SECTION.
*** binutils/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
Szabolcs Nagy <szabolcs.nagy@arm.com>
* readelf.c (get_aarch64_dynamic_type): New.
(get_dynamic_type): Use above for EM_AARCH64.
(dynamic_section_aarch64_val): New.
(process_dynamic_section): Use above for EM_AARCH64.
*** include/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
Szabolcs Nagy <szabolcs.nagy@arm.com>
* elf/aarch64.h (DT_AARCH64_BTI_PLT): New.
*** ld/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
Szabolcs Nagy <szabolcs.nagy@arm.com>
* NEWS: Document --force-bti.
* emultempl/aarch64elf.em (plt_type, bti_type, OPTION_FORCE_BTI): New.
(PARSE_AND_LIST_SHORTOPTS, PARSE_AND_LIST_OPTIONS): Add force-bti.
(PARSE_AND_LIST_ARGS_CASES): Handle OPTION_FORCE_BTI.
* testsuite/ld-aarch64/aarch64-elf.exp: Add all the tests below.
* testsuite/ld-aarch64/bti-plt-1.d: New test.
* testsuite/ld-aarch64/bti-plt-1.s: New test.
* testsuite/ld-aarch64/bti-plt-2.s: New test.
* testsuite/ld-aarch64/bti-plt-2.d: New test.
* testsuite/ld-aarch64/bti-plt-3.d: New test.
* testsuite/ld-aarch64/bti-plt-4.d: New test.
* testsuite/ld-aarch64/bti-plt-5.d: New test.
* testsuite/ld-aarch64/bti-plt-6.d: New test.
* testsuite/ld-aarch64/bti-plt-7.d: New test.
* testsuite/ld-aarch64/bti-plt-so.s: New test.
* testsuite/ld-aarch64/bti-plt.ld: New test.
This is part of the patch series to add support for BTI and
PAC in AArch64 linker.
This patch implements the following:
1) This extends in the gnu property support in the linker for
AArch64 by defining backend hooks for elf_backend_setup_gnu_properties,
elf_backend_merge_gnu_properties and elf_backend_parse_gnu_properties.
2) It defines AArch64 specific GNU property
GNU_PROPERTY_AARCH64_FEATURE_1_AND and 2 bit for BTI and PAC in it.
3) It also adds support in readelf.c to read and print these new
GNU properties in AArch64.
All these are made according to the new AArch64 ELF ABI
https://developer.arm.com/docs/ihi0056/latest/elf-for-the-arm-64-bit-architecture-aarch64-abi-2018q4
*** bfd/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
* elf-properties.c (_bfd_elf_link_setup_gnu_properties): Exclude
linker created inputs from merge.
* elfnn-aarch64.c (struct elf_aarch64_obj_tdata): Add field for
GNU_PROPERTY_AARCH64_FEATURE_1_AND properties.
(elfNN_aarch64_link_setup_gnu_properties): New.
(elfNN_aarch64_merge_gnu_properties): New.
(elf_backend_setup_gnu_properties): Define for AArch64.
(elf_backend_merge_gnu_properties): Likewise.
* elfxx-aarch64.c (_bfd_aarch64_elf_link_setup_gnu_properties): Define.
(_bfd_aarch64_elf_parse_gnu_properties): Define.
(_bfd_aarch64_elf_merge_gnu_properties): Define.
* elfxx-aarch64.h (_bfd_aarch64_elf_link_setup_gnu_properties): Declare.
(_bfd_aarch64_elf_parse_gnu_properties): Declare.
(_bfd_aarch64_elf_merge_gnu_properties): Declare.
(elf_backend_parse_gnu_properties): Define for AArch64.
*** binutils/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
* readelf.c (decode_aarch64_feature_1_and): New.
(print_gnu_property_note): Add case for AArch64 gnu notes.
*** include/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
* elf/common.h (GNU_PROPERTY_AARCH64_FEATURE_1_AND): New.
(GNU_PROPERTY_AARCH64_FEATURE_1_BTI): New.
(GNU_PROPERTY_AARCH64_FEATURE_1_PAC): New.
*** ld/ChangeLog ***
2019-03-13 Sudakshina Das <sudi.das@arm.com>
* NEWS: Document GNU_PROPERTY_AARCH64_FEATURE_1_BTI and
GNU_PROPERTY_AARCH64_FEATURE_1_PAC.
* testsuite/ld-aarch64/aarch64-elf.exp: Add run commands for new tests.
* testsuite/ld-aarch64/property-bti-pac1.d: New test.
* testsuite/ld-aarch64/property-bti-pac1.s: New test.
* testsuite/ld-aarch64/property-bti-pac2.d: New test.
* testsuite/ld-aarch64/property-bti-pac2.s: New test.
* testsuite/ld-aarch64/property-bti-pac3.d: New test.
Used for the AArch64 pointer authentication code mask registers in Arm v8.3-a.
NT_ARM_PAC_MASK matches the value in Linux include/uapi/linux/elf.h
include/ChangeLog:
* elf/common.h (NT_ARM_PAC_MASK): Add define.
bfd/ChangeLog:
* elf-bfd.h (elfcore_write_aarch_pauth): Add declaration.
* elf.c (elfcore_grok_aarch_pauth): New function.
(elfcore_grok_note): Check for NT_ARM_PAC_MASK.
(elfcore_write_aarch_pauth): New function.
(elfcore_write_register_note): Check for AArch64 pauth section.
Linkers group input note sections with the same name into one output
note section with the same name. One output note section is placed in
one PT_NOTE segment. New linkers merge all input .note.gnu.property
sections into one output .note.gnu.property section with a single
NT_GNU_PROPERTY_TYPE_0 note in a single PT_NOTE segment. Since older
linkers treat input .note.gnu.property section as a generic note section
and just concatenate all input .note.gnu.property sections into one
output .note.gnu.property section without merging them, we may
see one or more NT_GNU_PROPERTY_TYPE_0 notes in PT_NOTE segment, which
are invalid.
GNU_PROPERTY_X86_UINT32_VALID was defined to address this issue such
that linker sets the bit for non-relocatable outputs. But it isn't
sufficient:
1. It doesn't cover generic properties.
2. When -mx86-used-note=yes is passed to x86 assembler, the
GNU_PROPERTY_X86_UINT32_VALID bit is set in GNU_PROPERTY_X86_ISA_1_USED
property in object file and older linkers generate invalid
NT_GNU_PROPERTY_TYPE_0 notes with the GNU_PROPERTY_X86_UINT32_VALID bit
set.
I am proposing the following changes:
1. Add PT_GNU_PROPERTY segment type:
# define PT_GNU_PROPERTY (PT_LOOS + 0x474e553)
which covers .note.gnu.property section.
2. Remove GNU_PROPERTY_X86_UINT32_VALID.
bfd/
PR ld/23900
* elf.c (get_program_header_size): Add a PT_GNU_PROPERTY
segment for NOTE_GNU_PROPERTY_SECTION_NAME.
(_bfd_elf_map_sections_to_segments): Create a PT_GNU_PROPERTY
segment for NOTE_GNU_PROPERTY_SECTION_NAME.
* elfxx-x86.c (_bfd_elf_link_setup_gnu_properties): Don't set
GNU_PROPERTY_X86_UINT32_VALID.
binutils/
PR ld/23900
* readelf.c (get_segment_type): Support PT_GNU_PROPERTY.
(decode_x86_isa): Don't check GNU_PROPERTY_X86_UINT32_VALID.
(decode_x86_feature_1): Likewise.
(decode_x86_feature_2): Likewise.
(print_gnu_property_note): Remove GNU_PROPERTY_X86_UINT32_VALID
check.
* testsuite/binutils-all/i386/empty.d: Updated.
* testsuite/binutils-all/x86-64/empty-x32.d: Likewise.
* testsuite/binutils-all/x86-64/empty.d: Likewise.
* testsuite/binutils-all/i386/pr21231b.s: Change
GNU_PROPERTY_X86_ISA_1_USED bits to 0x7fffffff.
* testsuite/binutils-all/x86-64/pr21231b.s: Likewise.
gas/
PR ld/23900
* config/tc-i386.c (x86_cleanup): Don't set
GNU_PROPERTY_X86_UINT32_VALID.
* testsuite/gas/i386/property-1.s: Change
GNU_PROPERTY_X86_ISA_1_USED bits to 0.
include/
PR ld/23900
* elf/common.h (PT_GNU_PROPERTY): New.
(GNU_PROPERTY_X86_UINT32_VALID): Removed.
ld/
PR ld/23900
* testsuite/ld-elf/elf.exp: Run PR ld/23900 test.
* testsuite/ld-elf/pr23900-1-32.rd: New file.
* testsuite/ld-elf/pr23900-1-64.rd: Likewise.
* testsuite/ld-elf/pr23900-1.d: Likewise.
* testsuite/ld-elf/pr23900-1.s: Likewise.
* testsuite/ld-elf/pr23900-2.s: Likewise.
* testsuite/ld-elf/pr23900-2a.d: Likewise.
* testsuite/ld-elf/pr23900-2b.d: Likewise.
* testsuite/ld-i386/ibt-plt-1.d: Adjusted.
* testsuite/ld-i386/ibt-plt-2c.d: Likewise.
* testsuite/ld-i386/ibt-plt-2d.d: Likewise.
* testsuite/ld-i386/ibt-plt-3d.d: Likewise.
* testsuite/ld-x86-64/ibt-plt-1-x32.d: Likewise.
* testsuite/ld-x86-64/ibt-plt-1.d: Likewise.
* testsuite/ld-x86-64/ibt-plt-2c-x32.d: Likewise.
* testsuite/ld-x86-64/ibt-plt-2c.d: Likewise.
* testsuite/ld-x86-64/ibt-plt-2d-x32.d: Likewise.
* testsuite/ld-x86-64/ibt-plt-2c.d: Likewise.
* testsuite/ld-x86-64/ibt-plt-3c-x32.d: Likewise.
* testsuite/ld-x86-64/ibt-plt-3c.d: Likewise.
* testsuite/ld-x86-64/ibt-plt-3d-x32.d: Likewise.
* testsuite/ld-x86-64/ibt-plt-3d.d: Likewise.
* testsuite/ld-i386/pr23372c.d: Expect <None>
for GNU_PROPERTY_X86_ISA_1_USED.
* testsuite/ld-x86-64/pr23372c-x32.d: Likewise.
* testsuite/ld-x86-64/pr23372c.d: Likewise.
* testsuite/ld-x86-64/pr23372d-x32.d: Likewise.
* testsuite/ld-x86-64/pr23372d.d: Likewise.
* testsuite/ld-x86-64/property-x86-5a.s: Change
GNU_PROPERTY_X86_ISA_1_USED bits to 0.
* testsuite/ld-x86-64/property-x86-5b.s: Likewise.
Third party tools produce 32 bit relocs at index 6 with strange properties.
This change moves the existing 32 bit reloc (R_S12Z_EXT32) to index 7
and introduces a new one (R_S12Z_CW32) at index 6 to try to support code
generated by these tools.
* bfd/elf32-s12z.c (elf_s12z_howto_table) [R_S12Z_CW32]: New member.
* binutils/readelf.c (is_32bit_abs_reloc): Reloc type 7 is also 32 bit.
* include/elf/s12z.h (elf_s12z_reloc_tpe) [RELOC_NUMBER (R_S12Z_CW32)]: New enum.
This patch adds the new instruction and relocation as per proposal:
https://openrisc.io/proposals/ladrp
This is to be added to the spec in an upcoming revision. The new instruction
l.adrp loads the page offset of the current instruction offset by
a 21-bit immediate shifted left 13-bits. This is meant to be used with
a 13-bit lower bit page offset. This allows us to free up the got
register r16.
l.adrp r3, foo
l.ori r4, r3, po(foo)
l.lbz r5, po(foo)(r3)
l.sb po(foo)(r3), r6
The relocations we add are:
- BFD_RELOC_OR1K_PLTA26 For PLT jump relocation with PLT entry
asm: plta() implemented using l.ardp, meaning
no need for r16 (the GOT reg)
- BFD_RELOC_OR1K_GOT_PG21 Upper 21-bit Page offset got address
asm: got()
- BFD_RELOC_OR1K_TLS_GD_PG21 Upper 21-bit Page offset with TLS General
asm: tlsgd() Dynamic calculation
- BFD_RELOC_OR1K_TLS_LDM_PG21 Upper 21-bit Page offset with TLS local
asm: tlsldm() dynamic calculation
- BFD_RELOC_OR1K_TLS_IE_PG21 Upper 21-bit Page offset with TLS Initial
asm: gottp() Executable calculation
- BFD_RELOC_OR1K_PCREL_PG21 Default relocation for disp21 (l.adrp
instructions)
- BFD_RELOC_OR1K_LO13 low 13-bit page offset relocation
asm: po() i.e. mem loads, addi etc
- BFD_RELOC_OR1K_SLO13 low 13-bit page offset relocation
asm: po() i.e. mem stores, with split immediate
- BFD_RELOC_OR1K_GOT_LO13, low 13-bit page offset with GOT calcs
asm: gotpo()
- BFD_RELOC_OR1K_TLS_GD_LO13 Lower 13-bit offset with TLS GD calcs
asm: tlsgdpo()
- BFD_RELOC_OR1K_TLS_LDM_LO13 Lower 13-bit offset with TLS LD calcs
asm: tlsldmpo()
- BFD_RELOC_OR1K_TLS_IE_LO13 Lower 13-bit offset with TLS IE calcs
asm: gottppo()
bfd/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
* bfd-in2.h: Regenerated.
* elf32-or1k.c: (or1k_elf_howto_table): Fix formatting for
R_OR1K_PLT26, Add R_OR1K_PCREL_PG21, R_OR1K_GOT_PG21,
R_OR1K_TLS_GD_PG21, R_OR1K_TLS_LDM_PG21, R_OR1K_TLS_IE_PG21,
R_OR1K_LO13, R_OR1K_GOT_LO13, R_OR1K_TLS_GD_LO13, R_OR1K_TLS_LDM_LO13,
R_OR1K_TLS_IE_LO13, R_OR1K_SLO13, R_OR1K_PLTA26.
(or1k_reloc_map): Add BFD_RELOC_OR1K_PCREL_PG21,
BFD_RELOC_OR1K_GOT_PG21, BFD_RELOC_OR1K_TLS_GD_PG21,
BFD_RELOC_OR1K_TLS_LDM_PG21, BFD_RELOC_OR1K_TLS_IE_PG21,
BFD_RELOC_OR1K_LO13, BFD_RELOC_OR1K_GOT_LO13,
BFD_RELOC_OR1K_TLS_GD_LO13, BFD_RELOC_OR1K_TLS_GD_LO13,
BFD_RELOC_OR1K_TLS_LDM_LO13, BFD_RELOC_OR1K_TLS_IE_LO13,
BFD_RELOC_OR1K_SLO13, BFD_RELOC_OR1K_PLTA26.
(elf_or1k_link_hash_table): Add field saw_plta.
(or1k_final_link_relocate): Add value calculations for new relocations.
(or1k_elf_relocate_section): Add section relocations for new
relocations.
(or1k_write_plt_entry): New function.
(or1k_elf_finish_dynamic_sections): Add support for PLTA relocations
using new l.adrp instruction. Cleanup PLT relocation code generation.
* libbfd.h: Regenerated.
* reloc.c: Add BFD_RELOC_OR1K_PCREL_PG21, BFD_RELOC_OR1K_LO13,
BFD_RELOC_OR1K_SLO13, BFD_RELOC_OR1K_GOT_PG21, BFD_RELOC_OR1K_GOT_LO13,
BFD_RELOC_OR1K_PLTA26, BFD_RELOC_OR1K_TLS_GD_PG21,
BFD_RELOC_OR1K_TLS_GD_LO13, BFD_RELOC_OR1K_TLS_LDM_PG21,
BFD_RELOC_OR1K_TLS_LDM_LO13, BFD_RELOC_OR1K_TLS_IE_PG21,
BFD_RELOC_OR1K_TLS_IE_LO13.
cpu/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
* or1k.opc (parse_disp26): Add support for plta() relocations.
(parse_disp21): New function.
(or1k_rclass): New enum.
(or1k_rtype): New enum.
(or1k_imm16_relocs): Define new PO and SPO relocation mappings.
(parse_reloc): Add new po(), gotpo() and gottppo() for LO13 relocations.
(parse_imm16): Add support for the new 21bit and 13bit relocations.
* or1korbis.cpu (f-disp26): Don't assume SI.
(f-disp21): New pc-relative 21-bit 13 shifted to right.
(insn-opcode): Add ADRP.
(l-adrp): New instruction.
gas/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
* config/tc-or1k.c (or1k_apply_fix): Add BFD_RELOC_OR1K_TLS_GD_PG21,
BFD_RELOC_OR1K_TLS_GD_LO13, BFD_RELOC_OR1K_TLS_LDM_PG21,
BFD_RELOC_OR1K_TLS_LDM_LO13, BFD_RELOC_OR1K_TLS_IE_PG21,
BFD_RELOC_OR1K_TLS_IE_LO13.
* testsuite/gas/or1k/allinsn.s: Add test for l.adrp.
* testsuite/gas/or1k/allinsn.d: Add test results for new
instructions.
* testsuite/gas/or1k/reloc-1.s: Add tests to generate
R_OR1K_PLTA26, R_OR1K_GOT_PG21, R_OR1K_TLS_GD_PG21, R_OR1K_TLS_LDM_PG21,
R_OR1K_TLS_IE_PG21, R_OR1K_LO13, R_OR1K_GOT_LO13, R_OR1K_TLS_GD_LO13,
R_OR1K_TLD_LDM_LO13, R_OR1K_TLS_IE_LO13, R_OR1K_LO13, R_OR1K_SLO13
relocations.
* testsuite/gas/or1k/reloc-1.d: Add relocation results for
tests.
* testsuite/gas/or1k/reloc-2.s: Add negative tests for store to
gotpo().
* testsuite/gas/or1k/reloc-2.l: Add expected error test results.
ld/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
* testsuite/ld-or1k/or1k.exp: Add test cases for plt generation.
* testsuite/ld-or1k/plt1.dd: New file.
* testsuite/ld-or1k/plt1.s: New file.
* testsuite/ld-or1k/plt1.x.dd: New file.
* testsuite/ld-or1k/plta1.dd: New file.
* testsuite/ld-or1k/plta1.s: New file.
* testsuite/ld-or1k/pltlib.s: New file.
include/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
* elf/or1k.h (elf_or1k_reloc_type): Add R_OR1K_PCREL_PG21,
R_OR1K_GOT_PG21, R_OR1K_TLS_GD_PG21, R_OR1K_TLS_LDM_PG21,
R_OR1K_TLS_IE_PG21, R_OR1K_LO13, R_OR1K_GOT_LO13,
R_OR1K_TLS_GD_LO13, R_OR1K_TLS_LDM_LO13, R_OR1K_TLS_IE_LO13,
R_OR1K_SLO13, R_OR1K_PLTA26.
opcodes/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
* or1k-asm.c: Regenerated.
* or1k-desc.c: Regenerated.
* or1k-desc.h: Regenerated.
* or1k-dis.c: Regenerated.
* or1k-ibld.c: Regenerated.
* or1k-opc.c: Regenerated.
* or1k-opc.h: Regenerated.
* or1k-opinst.c: Regenerated.
This patch adds the following target relocations:
- BFD_RELOC_HI16_S High 16-bit relocation, for used with signed
asm: ha() lower.
- BFD_RELOC_HI16_S_GOTOFF High 16-bit GOT offset relocation for local
asm: gotoffha() symbols, for use with signed lower.
- BFD_RELOC_OR1K_TLS_IE_AHI16 High 16-bit TLS relocation with initial
asm: gottpoffha() executable calculation, for use with signed
lower.
- BFD_RELOC_OR1K_TLS_LE_AHI16 High 16-bit TLS relocation for local executable
asm: tpoffha() variables, for use with signed lower.
- BFD_RELOC_OR1K_SLO16 Split lower 16-bit relocation, used with
asm: lo() OpenRISC store instructions.
- BFD_RELOC_OR1K_GOTOFF_SLO16 Split lower 16-bit GOT offset relocation for
asm: gotofflo() local symbols, used with OpenRISC store
instructions.
- BFD_RELOC_OR1K_TLS_LE_SLO16 Split lower 16-bit relocation for TLS local
asm: tpofflo() executable variables, used with OpenRISC store
instructions.
bfd/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
Stafford Horne <shorne@gmail.com>
* bfd-in2.h: Regenerated.
* elf32-or1k.c (N_ONES): New macro.
(or1k_elf_howto_table): Fix R_OR1K_PLT26 to complain on overflow.
Add definitions for R_OR1K_TLS_TPOFF, R_OR1K_TLS_DTPOFF,
R_OR1K_TLS_DTPMOD, R_OR1K_AHI16, R_OR1K_GOTOFF_AHI16,
R_OR1K_TLS_IE_AHI16, R_OR1K_TLS_LE_AHI16, R_OR1K_SLO16,
R_OR1K_GOTOFF_SLO16, R_OR1K_TLS_LE_SLO16.
(or1k_reloc_map): Add entries for BFD_RELOC_HI16_S,
BFD_RELOC_LO16_GOTOFF, BFD_RELOC_HI16_GOTOFF, BFD_RELOC_HI16_S_GOTOFF,
BFD_RELOC_OR1K_TLS_IE_AHI16, BFD_RELOC_OR1K_TLS_LE_AHI16,
BFD_RELOC_OR1K_SLO16, BFD_RELOC_OR1K_GOTOFF_SLO16,
BFD_RELOC_OR1K_TLS_LE_SLO16.
(or1k_reloc_type_lookup): Change search loop to start ad index 0 and
also check results before returning.
(or1k_reloc_name_lookup): Simplify loop to use R_OR1K_max as index
limit.
(or1k_final_link_relocate): New function.
(or1k_elf_relocate_section): Add support for new AHI and SLO
relocations. Use or1k_final_link_relocate instead of generic
_bfd_final_link_relocate.
(or1k_elf_check_relocs): Add support for new AHI and SLO relocations.
* reloc.c: Add new enums for BFD_RELOC_OR1K_SLO16,
BFD_RELOC_OR1K_GOTOFF_SLO16, BFD_RELOC_OR1K_TLS_IE_AHI16,
BFD_RELOC_OR1K_TLS_IE_AHI16, BFD_RELOC_OR1K_TLS_LE_AHI16,
BFD_RELOC_OR1K_TLS_LE_SLO16. Remove unused BFD_RELOC_OR1K_GOTOFF_HI16
and BFD_RELOC_OR1K_GOTOFF_LO16.
* libbfd.h: Regenerated.
cpu/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
* or1k.opc: Add RTYPE_ enum.
(INVALID_STORE_RELOC): New string.
(or1k_imm16_relocs): New array array.
(parse_reloc): New static function that just does the parsing.
(parse_imm16): New static function for generic parsing.
(parse_simm16): Change to just call parse_imm16.
(parse_simm16_split): New function.
(parse_uimm16): Change to call parse_imm16.
(parse_uimm16_split): New function.
* or1korbis.cpu (simm16-split): Change to use new simm16_split.
(uimm16-split): Change to use new uimm16_split.
gas/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
* testsuite/gas/or1k/allinsn.d (l_ha): Add result for ha() relocation.
* testsuite/gas/or1k/allinsn.s (l_ha): Add test for ha() relocations.
* testsuite/gas/or1k/allinsn.exp: Renamed to or1k.exp.
* testsuite/gas/or1k/or1k.exp: Add reloc-2 list test.
* testsuite/gas/or1k/reloc-1.d: New file.
* testsuite/gas/or1k/reloc-1.s: New file.
* testsuite/gas/or1k/reloc-2.l: New file.
* testsuite/gas/or1k/reloc-2.s: New file.
include/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
* elf/or1k.h (elf_or1k_reloc_type): Add R_OR1K_AHI16,
R_OR1K_GOTOFF_AHI16, R_OR1K_TLS_IE_AHI16, R_OR1K_TLS_LE_AHI16,
R_OR1K_SLO16, R_OR1K_GOTOFF_SLO16, R_OR1K_TLS_LE_SLO16.
ld/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
* testsuite/ld-or1k/offsets1.d: New file.
* testsuite/ld-or1k/offsets1.s: New file.
* testsuite/ld-or1k/or1k.exp: New file.
opcodes/ChangeLog:
yyyy-mm-dd Richard Henderson <rth@twiddle.net>
* or1k-asm.c: Regenerate.
Inserted offset in final section in the GOT entry of type DTSOFF soon to be
relocated by the dynamic loader.
bfd/
2018-09-06 Cupertino Miranda <cmiranda@synopsys.com>
* arc-got.h (relocate_fix_got_relocs_for_got_info): Changed. Take TLS
section alignment in consideration for this relocation.
* elf32-arc.c (FINAL_SECTSTART): Added this formula macro.
(ARC_TLS_DTPOFF) Updated reloc to use new created macro instead.
We shouldn't include zero size sections at start of PT_NOTE segment,
similar to PT_DYNAMIC segment.
PR binutils/23694
* include/elf/internal.h (ELF_SECTION_IN_SEGMENT_1): Don't
include zero size sections at start of PT_NOTE segment.
We have not only removed all unsupported and obsolete code, but also supported lost of new features,
including better link-time relaxations and TLS implementations. Besides, the files generated by the
newly assembler and linker usually get higher performance and more optimized code size.
ld * emultempl/nds32elf.em (hyper_relax): New variable.
(nds32_elf_create_output_section_statements):
the parameters of bfd_elf32_nds32_set_target_option
(PARSE_AND_LIST_PROLOGUE, PARSE_AND_LIST_OPTIONS,
PARSE_AND_LIST_ARGS_CASES): Add new option --mhyper-relax.
* emultempl/nds32elf.em (nds32_elf_after_open): Updated.
* emultempl/nds32elf.em (tls_desc_trampoline): New variable.
* (nds32_elf_create_output_section_statements): Updated.
* (nds32_elf_after_parse): Disable relaxations when PIC is enable.
* (PARSE_AND_LIST_PROLOGUE, PARSE_AND_LIST_OPTIONS,
PARSE_AND_LIST_ARGS_CASES): Add new option --m[no-]tlsdesc-trampoline.
include * elf/nds32.h: Remove the unused target features.
* dis-asm.h (disassemble_init_nds32): Declared.
* elf/nds32.h (E_NDS32_NULL): Removed.
(E_NDS32_HAS_DSP_INST, E_NDS32_HAS_ZOL): New.
* opcode/nds32.h: Ident.
(N32_SUB6, INSN_LW): New macros.
(enum n32_opcodes): Updated.
* elf/nds32.h: Doc fixes.
* elf/nds32.h: Add R_NDS32_LSI.
* elf/nds32.h: Add new relocations for TLS.
gas * config/tc-nds32.c: Remove the unused target features.
(nds32_relax_relocs, md_pseudo_table, nds32_elf_record_fixup_exp,
nds32_set_elf_flags_by_insn, nds32_insert_relax_entry,
nds32_apply_fix): Likewise.
(nds32_no_ex9_begin): Removed.
* config/tc-nds32.c (add_mapping_symbol_for_align,
make_mapping_symbol, add_mapping_symbol): New functions.
* config/tc-nds32.h (enum mstate): New.
(nds32_segment_info_type): Likewise.
* configure.ac (--enable-dsp-ext, --enable-zol-ext): New options.
* config.in: Regenerated.
* configure: Regenerated.
* config/tc-nds32.c (nds32_dx_regs):
Set the value according to the configuration.
(nds32_perf_ext, nds32_perf_ext2, nds32_string_ext, nds32_audio_ext):
Likewise.
(nds32_dsp_ext): New variable. Set the value according to the
configuration.
(nds32_zol_ext): Likewise.
(asm_desc, nds32_pseudo_opcode_table): Make them static.
(nds32_set_elf_flags_by_insn): Updated.
(nds32_check_insn_available): Updated.
(nds32_str_tolower): New function.
* config/tc-nds32.c (relax_table): Updated.
(md_begin): Updated.
(md_assemble): Use XNEW macro to allocate space for `insn.info',
and then remember to free it.
(md_section_align): Cast (-1) to ValueT.
(nds32_get_align): Cast (~0U) to addressT.
(nds32_relax_branch_instructions): Updated.
(md_convert_frag): Add new local variable `final_r_type'.
(invalid_prev_frag): Add new bfd_boolean parameter `relax'.
All callers changed.
* config/tc-nds32.c (struct nds32_relocs_pattern): Add `insn' field.
(struct nds32_hint_map): Add `option_list' field.
(struct suffix_name, suffix_table): Remove the unused `pic' field.
(do_pseudo_b, do_pseudo_bal): Remove the suffix checking.
(do_pseudo_la_internal, do_pseudo_pushpopm): Indent.
(relax_hint_bias, relax_hint_id_current): New static variables.
(reset_bias, relax_hint_begin): New variables.
(nds_itoa): New function.
(CLEAN_REG, GET_OPCODE): New macros.
(struct relax_hint_id): New.
(nds32_relax_hint): For .relax_hint directive, we can use `begin'
and `end' to mark the relax pattern without giving exactly id number.
(nds32_elf_append_relax_relocs): Handle the case that the .relax_hint
directives are attached to pseudo instruction.
(nds32_elf_save_pseudo_pattern): Change the second parameter from
instruction's opcode to byte code.
(nds32_elf_build_relax_relation): Add new bfd_boolean parameter
`pseudo_hint'.
(nds32_lookup_pseudo_opcode): Fix the overflow issue.
(enum nds32_insn_type): Add N32_RELAX_ALU1 and N32_RELAX_16BIT.
(nds32_elf_record_fixup_exp, relax_ls_table, hint_map,
nds32_find_reloc_table, nds32_match_hint_insn, nds32_parse_name):
Updated.
* config/tc-nds32.h (MAX_RELAX_NUM): Extend it to 6.
(enum nds32_relax_hint_type): Merge NDS32_RELAX_HINT_LA and
NDS32_RELAX_HINT_LS into NDS32_RELAX_HINT_LALS. Add
NDS32_RELAX_HINT_LA_PLT, NDS32_RELAX_HINT_LA_GOT and
NDS32_RELAX_HINT_LA_GOTOFF.
* config/tc-nds32.h (relax_ls_table): Add floating load/store
to gp relax pattern.
(hint_map, nds32_find_reloc_table): Likewise.
* configure.ac: Define NDS32_LINUX_TOOLCHAIN.
* configure: Regenerated.
* config.in: Regenerated.
* config/tc-nds32.h (enum nds32_ramp): Updated.
(enum nds32_relax_hint_type): Likewise.
* config/tc-nds32.c: Include "errno.h" and "limits.h".
(relax_ls_table): Add TLS relax patterns.
(nds32_elf_append_relax_relocs): Attach BFD_RELOC_NDS32_GROUP on
each instructions of TLS patterns.
(nds32_elf_record_fixup_exp): Updated.
(nds32_apply_fix): Likewise.
(suffix_table): Add TLSDESC suffix.
binutils* testsuite/binutils-all/objcopy.exp: Set the unsupported reloc number
from 215 to 255 for NDS32.
bfd * elf32-nds32.c (nds32_elf_relax_loadstore):
Remove the unused target features.
(bfd_elf32_nds32_set_target_option): Remove the unused parameters.
(nds32_elf_relax_piclo12, nds32_elf_relax_letlslo12,
nds32_elf_relax_letlsadd, nds32_elf_relax_letlsls,
nds32_elf_relax_pltgot_suff, nds32_elf_relax_got_suff
nds32_elf_relax_gotoff_suff, calculate_plt_memory_address,
calculate_plt_offset, calculate_got_memory_address,
nds32_elf_check_dup_relocs): Removed.
All callers changed.
* elf32-nds32.h: Remove the unused macros and defines.
(elf_nds32_link_hash_table): Remove the unused variable.
(bfd_elf32_nds32_set_target_option): Update prototype.
(nds32_elf_ex9_init): Removed.
* elf32-nds32.c (nds32_convert_32_to_16): Updated.
* elf32-nds32.c (HOWTO2, HOWTO3): Define new HOWTO macros
to initialize array nds32_elf_howto_table in any order
without lots of EMPTY_HOWTO.
(nds32_reloc_map): Updated.
* reloc.c: Add BFD_RELOC_NDS32_LSI.
* bfd-in2.h: Regenerated.
* bfd/libbfd.h: Regenerated.
* elf32-nds32.c (nds32_elf_relax_howto_table): Add R_NDS32_LSI.
(nds32_reloc_map): Likewise.
(nds32_elf_relax_flsi): New function.
(nds32_elf_relax_section): Support floating load/store relaxation.
* elf32-nds32.c (NDS32_GUARD_SEC_P, elf32_nds32_local_gp_offset):
New macro.
(struct elf_nds32_link_hash_entry): New `offset_to_gp' field.
(struct elf_nds32_obj_tdata): New `offset_to_gp' and `hdr_size' fields.
(elf32_nds32_allocate_local_sym_info, nds32_elf_relax_guard,
nds32_elf_is_target_special_symbol, nds32_elf_maybe_function_sym):
New functions.
(nds32_info_to_howto_rel): Add BFD_ASSERT.
(bfd_elf32_bfd_reloc_type_table_lookup, nds32_elf_link_hash_newfunc,
nds32_elf_link_hash_table_create, nds32_elf_relocate_section,
nds32_elf_relax_loadstore, nds32_elf_relax_lo12, nds32_relax_adjust_label,
bfd_elf32_nds32_set_target_option, nds32_fag_mark_relax): Updated.
(nds32_elf_final_sda_base): Improve it to find the better gp value.
(insert_nds32_elf_blank): Must consider `len' when inserting blanks.
* elf32-nds32.h (bfd_elf32_nds32_set_target_option): Update prototype.
(struct elf_nds32_link_hash_table): Add new variable `hyper_relax'.
* elf32-nds32.c (elf32_nds32_allocate_dynrelocs): New function.
(create_got_section): Likewise.
(allocate_dynrelocs, nds32_elf_size_dynamic_sections,
nds32_elf_relocate_section, nds32_elf_finish_dynamic_symbol): Updated.
(nds32_elf_check_relocs): Fix the issue that the shared library may
has TEXTREL entry in the dynamic section.
(nds32_elf_create_dynamic_sections): Enable to call readonly_dynrelocs
since the TEXTREL issue is fixed in the nds32_elf_check_relocs.
(nds32_elf_finish_dynamic_sections): Update and add DT_RELASZ
dynamic entry.
(calculate_offset): Remove the unused parameter `pic_ext_target' and
related codes.
All callers changed.
(elf_backend_dtrel_excludes_plt): Disable it temporarily since it
will cause some errors for our test cases.
* elf32-nds32.c (nds32_elf_merge_private_bfd_data): Allow to link the
generic object.
* reloc.c: Add TLS relocations.
* libbfd.h: Regenerated.
* bfd-in2.h: Regenerated.
* elf32-nds32.h (struct section_id_list_t): New.
(elf32_nds32_lookup_section_id, elf32_nds32_check_relax_group,
elf32_nds32_unify_relax_group, nds32_elf_unify_tls_model):
New prototypes.
(elf32_nds32_compute_jump_table_size, elf32_nds32_local_tlsdesc_gotent):
New macro.
(nds32_insertion_sort, bfd_elf32_nds32_set_target_option,
elf_nds32_link_hash_table): Updated.
* elf32-nds32.c (enum elf_nds32_tls_type): New.
(struct elf32_nds32_relax_group_t, struct relax_group_list_t): New.
(elf32_nds32_add_dynreloc, patch_tls_desc_to_ie, get_tls_type,
fls, ones32, list_insert, list_insert_sibling, dump_chain,
elf32_nds32_check_relax_group, elf32_nds32_lookup_section_id,
elf32_nds32_unify_relax_group, nds32_elf_unify_tls_model): New functions.
(elf_nds32_obj_tdata): Add new fields.
(elf32_nds32_relax_group_ptr, nds32_elf_local_tlsdesc_gotent): New macros.
(nds32_elf_howto_table): Add TLS relocations.
(nds32_reloc_map): Likewise.
(nds32_elf_copy_indirect_symbol, nds32_elf_size_dynamic_sections,
nds32_elf_finish_dynamic_symbol, elf32_nds32_allocate_local_sym_info,
nds32_elf_relocate_section, bfd_elf32_nds32_set_target_option,
nds32_elf_check_relocs, allocate_dynrelocs): Updated.
(nds32_elf_relax_section): Call nds32_elf_unify_tls_model.
(dtpoff_base): Rename it to `gottpof' and then update it.
opcodes * nds32-asm.c (operand_fields): Remove the unused fields.
(nds32_opcodes): Remove the unused instructions.
* nds32-dis.c (nds32_ex9_info): Removed.
(nds32_parse_opcode): Updated.
(print_insn_nds32): Likewise.
* nds32-asm.c (config.h, stdlib.h, string.h): New includes.
(LEX_SET_FIELD, LEX_GET_FIELD): Update defines.
(nds32_asm_init, build_operand_hash_table, build_keyword_hash_table,
build_opcode_hash_table): New functions.
(nds32_keyword_table, nds32_keyword_count_table, nds32_field_table,
nds32_opcode_table): New.
(hw_ktabs): Declare it to a pointer rather than an array.
(build_hash_table): Removed.
* nds32-asm.h (enum): Add SYN_INPUT, SYN_OUTPUT, SYN_LOPT,
SYN_ROPT and upadte HW_GPR and HW_INT.
* nds32-dis.c (keywords): Remove const.
(match_field): New function.
(nds32_parse_opcode): Updated.
* disassemble.c (disassemble_init_for_target):
Add disassemble_init_nds32.
* nds32-dis.c (eum map_type): New.
(nds32_private_data): Likewise.
(get_mapping_symbol_type, is_mapping_symbol, nds32_symbol_is_valid,
nds32_add_opcode_hash_table, disassemble_init_nds32): New functions.
(print_insn_nds32): Updated.
* nds32-asm.c (parse_aext_reg): Add new parameter.
(parse_re, parse_re2, parse_aext_reg): Only reduced registers
are allowed to use.
All callers changed.
* nds32-asm.c (keyword_usr, keyword_sr): Updated.
(operand_fields): Add new fields.
(nds32_opcodes): Add new instructions.
(keyword_aridxi_mx): New keyword.
* nds32-asm.h (enum): Add NASM_ATTR_DSP_ISAEXT, HW_AEXT_ARIDXI_MX
and NASM_ATTR_ZOL.
(ALU2_1, ALU2_2, ALU2_3): New macros.
* nds32-dis.c (nds32_filter_unknown_insn): Updated.
Currently, three tests FAIL on Solaris 11.4+ (amd64-pc-solaris2.11 and
sparcv9-sun-solaris2.11):
info auxv
[...]
2009 AT_SUN_HWCAP Machine-dependent CPU capability hints 0x3f5ff7
2023 ??? 0x0
0 AT_NULL End of vector 0x0
(gdb) WARNING: Unrecognized tag value: 2023 ??? 0x0
FAIL: gdb.base/auxv.exp: info auxv on live process
info auxv
4294969310 ??? 0x7fffbfffe410
9225589753816 ??? 0x7fffbfffe45c
[...]
WARNING: Unrecognized tag value: 4294969310 ??? 0x7fffbfffe410
WARNING: Unrecognized tag value: 9225589753816 ??? 0x7fffbfffe45c
WARNING: Unrecognized tag value: 140733193388037 ??? 0x6
[...]
2009 AT_SUN_HWCAP Machine-dependent CPU capability hints 0x3f5ff7
2023 ??? 0x0
0 AT_NULL End of vector 0x0
(gdb) WARNING: Unrecognized tag value: 2023 ??? 0x0
UNRESOLVED: gdb.base/auxv.exp: info auxv on native core dump
info auxv
[...]
2009 AT_SUN_HWCAP Machine-dependent CPU capability hints 0x3f5ff7
2023 ??? 0x0
0 AT_NULL End of vector 0x0
(gdb) WARNING: Unrecognized tag value: 2023 ??? 0x0
FAIL: gdb.base/auxv.exp: info auxv on gcore-created dump
The following patch fixes this by introducing the missing AT_SUN_*
values from Solaris 11.4+ <sys/auxv.h>. This lets the live and
gcore-created dump tests PASS.
I don't know yet what's the reason for those weird 'Unrecognized tag
value' warnings with native core dumps is; elfdump -n certainly doesn't
show them. However, native core dumps still need quite some work
(mostly in bfd) in this and other areas.
Tested on amd64-pc-solaris2.11.
gdb:
* auxv.c (default_print_auxv_entry): Reflect AT_SUN_CAP_HW1
renaming.
Handle AT_SUN_EMULATOR, AT_SUN_BRANDNAME, AT_SUN_BRAND_AUX1,
AT_SUN_BRAND_AUX2, AT_SUN_BRAND_AUX3, AT_SUN_CAP_HW2.
include:
* elf/common.h (AT_SUN_HWCAP): Rename to ...
(AT_SUN_CAP_HW1): ... this. Retain old name for backward
compatibility.
(AT_SUN_EMULATOR, AT_SUN_BRANDNAME, AT_SUN_BRAND_AUX1)
(AT_SUN_BRAND_AUX2, AT_SUN_BRAND_AUX3, AT_SUN_CAP_HW2): Define.
The older linker treats .note.gnu.property section as a generic note
and just concatenates all .note.gnu.property sections from the input
to the output. On CET-enabled OS, the output of the older linker is
marked as CET enabled, but in fact, it is not CET enabled and it crashes
on CET-enabled machines.
This patch defines GNU_PROPERTY_X86_UINT32_VALID. Linker is updated to
set the GNU_PROPERTY_X86_UINT32_VALID bit in GNU property note for
non-relocatable output to differentiate outputs from the older linker.
bfd/
* elfxx-x86.c (_bfd_x86_elf_parse_gnu_properties): Mask out the
GNU_PROPERTY_X86_UINT32_VALID bit.
(_bfd_x86_elf_link_fixup_gnu_properties): Set the
GNU_PROPERTY_X86_UINT32_VALID bit for non-relocatable output.
binutils/
* readelf.c (print_gnu_property_note): Check the
GNU_PROPERTY_X86_UINT32_VALID bit for invalid GNU property note.
include/
* elf/common.h (GNU_PROPERTY_X86_UINT32_VALID): New.
* bfd/elf32-s12z.c: (opru18_reloc): New function.
* bfd/elf32-s12z.c: (elf_s12z_howto_table): Adjust Howto according to new knowledge.
* include/elf/s12z.h: Rename R_S12Z_UKNWN_3 to R_S12Z_EXT18.
This patch adds a few comments to include/elf/arm.h to clarify which
versions of the ARM ELF specification defined which headers. Given
that the EABI is pretty ubiquitous these days, I've marked anything
not based on that as deprecated.
There are no plans to remove any deprecated definitions at this time,
but any new development shouldn't be building upon support for
deprecated definitions remaining in the long term.
* elf/arm.h: Updated comments for e_flags definitions.
This patch series is a new binutils port for C-SKY processors, including support for both the V1 and V2 processor variants. V1 is derived from the MCore architecture while V2 is substantially different, with mixed 16- and 32-bit instructions, a larger register set, a different (but overlapping) ABI, etc. There is support for bare-metal ELF targets and Linux with both glibc and uClibc.
This code is being contributed jointly by C-SKY Microsystems and Mentor Graphics. C-SKY is responsible for the technical content and has proposed Lifang Xia and Yunhai Shang as port maintainers. (Note that C-SKY does have a corporate copyright assignment on file with the FSF.) Mentor Graphics' role has been cleaning up the code, adding documentation and additional test cases, etc, to address issues we anticipated reviewers would complain about.
bfd * Makefile.am (ALL_MACHINES, ALL_MACHINES_CFILES): Add C-SKY.
(BFD32_BACKENDS, BFD_BACKENDS_CFILES): Likewise.
* Makefile.in: Regenerated.
* archures.c (enum bfd_architecture): Add bfd_arch_csky and
related bfd_mach defines.
(bfd_csky_arch): Declare.
(bfd_archures_list): Add C-SKY.
* bfd-in.h (elf32_csky_build_stubs): Declare.
(elf32_csky_size_stubs): Declare.
(elf32_csky_next_input_section: Declare.
(elf32_csky_setup_section_lists): Declare.
* bfd-in2.h: Regenerated.
* config.bfd: Add C-SKY.
* configure.ac: Likewise.
* configure: Regenerated.
* cpu-csky.c: New file.
* elf-bfd.h (enum elf_target_id): Add C-SKY.
* elf32-csky.c: New file.
* libbfd.h: Regenerated.
* reloc.c: Add C-SKY relocations.
* targets.c (csky_elf32_be_vec, csky_elf32_le_vec): Declare.
(_bfd_target_vector): Add C-SKY target vector entries.
binutils* readelf.c: Include elf/csky.h.
(guess_is_rela): Handle EM_CSKY.
(dump_relocations): Likewise.
(get_machine_name): Likewise.
(is_32bit_abs_reloc): Likewise.
include * dis-asm.h (csky_symbol_is_valid): Declare.
* opcode/csky.h: New file.
opcodes * Makefile.am (TARGET_LIBOPCODES_CFILES): Add csky-dis.c.
* Makefile.in: Regenerated.
* configure.ac: Add C-SKY.
* configure: Regenerated.
* csky-dis.c: New file.
* csky-opc.h: New file.
* disassemble.c (ARCH_csky): Define.
(disassembler, disassemble_init_for_target): Add case for ARCH_csky.
* disassemble.h (print_insn_csky, csky_get_disassembler): Declare.
gas * Makefile.am (TARGET_CPU_CFILES): Add entry for C-SKY.
(TARGET_CPU_HFILES, TARGET_ENV_HFILES): Likewise.
* Makefile.in: Regenerated.
* config/tc-csky.c: New file.
* config/tc-csky.h: New file.
* config/te-csky_abiv1.h: New file.
* config/te-csky_abiv1_linux.h: New file.
* config/te-csky_abiv2.h: New file.
* config/te-csky_abiv2_linux.h: New file.
* configure.tgt: Add C-SKY.
* doc/Makefile.am (CPU_DOCS): Add entry for C-SKY.
* doc/Makefile.in: Regenerated.
* doc/all.texi: Set CSKY feature.
* doc/as.texi (Overview): Add C-SKY options.
(Machine Dependencies): Likewise.
* doc/c-csky.texi: New file.
* testsuite/gas/csky/*: New test cases.
ld * Makefile.am (ALL_EMULATION_SOURCES): Add C-SKY emulations.
(ecskyelf.c, ecskyelf_linux.c): New rules.
* Makefile.in: Regenerated.
* configure.tgt: Add C-SKY.
* emulparams/cskyelf.sh: New file.
* emulparams/cskyelf_linux.sh: New file.
* emultempl/cskyelf.em: New file.
* gen-doc.texi: Add C-SKY.
* ld.texi: Likewise.
(Options specific to C-SKY targets): New section.
* testsuite/ld-csky/*: New tests.
Fix an issue with commit 8095d2f70e ("MIPS/GAS: Split Loongson MMI
Instructions from loongson2f/3a"), AFL_ASE_MASK should be 0x0006ffff
instead of 0x0004ffff.
2018-07-27 Chenghua Xu <paul.hua.gm@gmail.com>
Maciej W. Rozycki <macro@linux-mips.org>
include/
* elf/mips.h (AFL_ASE_MASK): Correct typo.
This adds support for ".localentry 1", a new st_other
STO_PPC64_LOCAL_MASK encoding that signifies a function with a single
entry point like ".localentry 0", but unlike a ".localentry 0"
function does not preserve r2.
include/
* elf/ppc64.h: Specify byte offset to local entry for values
of two to six in STO_PPC64_LOCAL_MASK. Clarify r2 return
value for such functions when entering via global entry point.
Specify meaning of a value of one in STO_PPC64_LOCAL_MASK.
bfd/
* elf64-ppc.c (ppc64_elf_size_stubs): Use a ppc_stub_long_branch_r2off
for calls to symbols with STO_PPC64_LOCAL_MASK bits set to 1.
gas/
* config/tc-ppc.c (ppc_elf_localentry): Allow .localentry values
of 1 and 7 to directly set value into STO_PPC64_LOCAL_MASK bits.
ld/testsuite/
* ld-powerpc/elfv2.s: Add .localentry f5,1 testcase.
* ld-powerpc/elfv2exe.d: Update.
* ld-powerpc/elfv2so.d: Update.
The MMI instruction set has been implemented in many Loongson
processors. There is a lot of software optimized for MMI. This patch
splits MMI from loongson2f/3a, and adds GAS and disassembler options for
MMI instructions.
2018-07-20 Chenghua Xu <paul.hua.gm@gmail.com>
Maciej W. Rozycki <macro@mips.com>
bfd/
* elfxx-mips.c (print_mips_ases): Add MMI extension.
binutils/
* readelf.c (print_mips_ases): Add MMI extension.
gas/
* NEWS: Mention MultiMedia extensions Instructions (MMI)
support.
* config/tc-mips.c (options): Add OPTION_LOONGSON_MMI and
OPTION_NO_LOONGSON_MMI.
(md_longopts): Likewise.
(mips_ases): Define availability for MMI.
(mips_convert_ase_flags): Map ASE_LOONGSON_MMI to
AFL_ASE_LOONGSON_MMI.
(mips_cpu_info_table): Add ASE_LOONGSON_MMI for loongson2f/3a.
(md_show_usage): Add help for -mloongson-mmi and
-mno-loongson-mmi.
* doc/as.texi: Document -mloongson-mmi, -mno-loongson-mmi.
* doc/c-mips.texi: Document -mloongson-mmi, -mno-loongson-mmi,
.set loongson-mmi and .set noloongson-mmi.
* testsuite/gas/mips/loongson-2f.d: Move mmi test to ...
* testsuite/gas/mips/loongson-2f-mmi.d: Here. Add ISA/ASE
flag verification.
* testsuite/gas/mips/loongson-2f.s: Move mmi test to ...
* testsuite/gas/mips/loongson-2f-mmi.s: Here.
* testsuite/gas/mips/loongson-3a.d: Move mmi test to ...
* testsuite/gas/mips/loongson-3a-mmi.d: Here. Add ISA/ASE
flag verification.
* testsuite/gas/mips/loongson-3a.s: Move mmi test to ...
* testsuite/gas/mips/loongson-3a-mmi.s: Here.
* testsuite/gas/mips/mips.exp: Run loongson-2f-mmi and
loongson-3a-mmi tests.
include/
* elf/mips.h (AFL_ASE_MMI): New macro.
(AFL_ASE_MASK): Update to include AFL_ASE_LOONGSON_MMI.
* opcode/mips.h (ASE_LOONGSON_MMI): New macro.
opcodes/
* mips-dis.c (mips_arch_choices): Add MMI to loongson2f and
loongson3a descriptors.
(parse_mips_ase_option): Handle -M loongson-mmi option.
(print_mips_disassembler_options): Document -M loongson-mmi.
* mips-opc.c (LMMI): New macro.
(mips_opcodes): Replace IL2F|IL3A marking with LMMI for MMI
instructions.
For sections that are not SHT_NOBITS, use sh_offset and p_offset instead of
sh_addr and p_vaddr when calculating if a section fits in a segment. Both
methods are valid when using the GNU linker.
include/
* elf/internal.h (ELF_SECTION_IN_SEGMENT): Don’t check addresses
for non SHT_NOBITS.
Alan Modra
Mihailo Stojanovic
Szabolcs Nagy
Jose E. Marchesi
Andre Vieira
H.J. Lu
Sudakshina Das
Alan Hayward
Jim Wilson
Yoshinori Sato
John Baldwin
John Darrington
Stafford Horne
Richard Henderson
Cupertino Miranda
Nick Clifton
Rainer Orth
Chenghua Xu
Richard Earnshaw
claziss
Andrew Jenner