Implement the missing registers for the TZ MPC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-3-peter.maydell@linaro.org
Implement the Arm TrustZone Memory Protection Controller, which sits
in front of RAM and allows secure software to configure it to either
pass through or reject transactions.
We implement the MPC as a QEMU IOMMU, which will direct transactions
either through to the devices and memory behind it or to a special
"never works" AddressSpace if they are blocked.
This initial commit implements the skeleton of the device:
* it always permits accesses
* it doesn't implement most of the registers
* it doesn't implement the interrupt or other behaviour
for blocked transactions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-2-peter.maydell@linaro.org
With this patch, virt-3.0 machine uses a new 256MB ECAM region
by default instead of the legacy 16MB one, if highmem is set
(LPAE supported by the guest) and (!firmware_loaded || aarch64).
Indeed aarch32 mode FW may not support this high ECAM region.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-11-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch defines a new ECAM region located after the 256GB limit.
The virt machine state is augmented with a new highmem_ecam field
which guards the usage of this new ECAM region instead of the legacy
16MB one. With the highmem ECAM region, up to 256 PCIe buses can be
used.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-9-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allows the creation of a GICv3 node with 1 or 2
redistributor regions depending on the number of smu_cpus.
The second redistributor region is located just after the
existing RAM region, at 256GB and contains up to up to 512 vcpus.
Please refer to kernel documentation for further node details:
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-6-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To prepare for multiple redistributor regions, we introduce
an array of uint32_t properties that stores the redistributor
count of each redistributor region.
Non accelerated VGICv3 only supports a single redistributor region.
The capacity of all redist regions is checked against the number of
vcpus.
Machvirt is updated to set those properties, ie. a single
redistributor region with count set to the number of vcpus
capped by 123.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-4-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The way we used to handle KVM allowable guest pagesizes for PAPR guests
required some convoluted checking of memory attached to the guest.
The allowable pagesizes advertised to the guest cpus depended on the memory
which was attached at boot, but then we needed to ensure that any memory
later hotplugged didn't change which pagesizes were allowed.
Now that we have an explicit machine option to control the allowable
maximum pagesize we can simplify this. We just check all memory backends
against that declared pagesize. We check base and cold-plugged memory at
reset time, and hotplugged memory at pre_plug() time.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The way the POWER Hash Page Table (HPT) MMU is virtualized by KVM HV means
that every page that the guest puts in the pagetables must be truly
physically contiguous, not just GPA-contiguous. In effect this means that
an HPT guest can't use any pagesizes greater than the host page size used
to back its memory.
At present we handle this by changing what we advertise to the guest based
on the backing pagesizes. This is pretty bad, because it means the guest
sees a different environment depending on what should be host configuration
details.
As a start on fixing this, we add a new capability parameter to the
pseries machine type which gives the maximum allowed pagesizes for an
HPT guest. For now we just create and validate the parameter without
making it do anything.
For backwards compatibility, on older machine types we set it to the max
available page size for the host. For the 3.0 machine type, we fix it to
16, the intention being to only allow HPT pagesizes up to 64kiB by default
in future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
As well as being able to generate its own i2c transactions, the ppc4xx
i2c controller has a DIRECTCNTL register which allows explicit control
of the i2c lines.
Using this register an OS can directly bitbang i2c operations. In
order to let emulated i2c devices respond to this, we need to wire up
the DIRECTCNTL register to qemu's bitbanged i2c handling code.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
We don't emulate slave mode so related registers are not needed.
[lh]sadr are only retained to avoid too many warnings and simplify
debugging but sdata is not even correct because device has a 4 byte
FIFO instead so just remove this unimplemented register for now.
The intr register is also not implemented correctly, it is for
diagnostics and normally not even visible on device without explicitly
enabling it. As no guests are known to need this remove it as well.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr_irq_alloc_block and spapr_irq_alloc() are now deprecated.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Today, when a device requests for IRQ number in a sPAPR machine, the
spapr_irq_alloc() routine first scans the ICSState status array to
find an empty slot and then performs the assignement of the selected
numbers. Split this sequence in two distinct routines : spapr_irq_find()
for lookups and spapr_irq_claim() for claiming the IRQ numbers.
This will ease the introduction of a static layout of IRQ numbers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
spapr capabilities have an apply hook to actually activate (or deactivate)
the feature in the system at reset time. However, a number of capabilities
affect the setup of cpus, and need to be applied to each of them -
including hotplugged cpus for extra complication. To make this simpler,
add an optional cpu_apply hook that is called from spapr_cpu_reset().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Previously, the effective values of the various spapr capability flags
were only determined at machine reset time. That was a lazy way of making
sure it was after cpu initialization so it could use the cpu object to
inform the defaults.
But we've now improved the compat checking code so that we don't need to
instantiate the cpus to use it. That lets us move the resolution of the
capability defaults much earlier.
This is going to be necessary for some future capabilities.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
It introduces a base PnvChip class from which the specific processor
chip classes, Pnv8Chip and Pnv9Chip, inherit. Each of them needs to
define an init and a realize routine which will create the controllers
of the target processor. For the moment, the base PnvChip class
handles the XSCOM bus and the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
A per-CPU machine data pointer was recently added to PowerPCCPU. The
motivation is to to hide platform specific details from the core CPU
code. This per-CPU data can hold state which is relevant to the guest
though, eg, Virtual Processor Areas, and we should migrate this state.
This patch adds the plumbing so that we can migrate the per-CPU data
for PAPR guests. We only do this for newer machine types for the sake
of backward compatibility. No state is migrated for the moment: the
vmstate_spapr_cpu_state structure will be populated by subsequent
patches.
Signed-off-by: Greg Kurz <groug@kaod.org>
[dwg: Fix some trivial spelling and spacing errors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This moves the details of the ISA bus creation under the LPC model but
more important, the new PnvChip operation will let us choose the chip
class to use when we introduce the different chip classes for Power9
and Power8. It hides away the processor chip controllers from the
machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
On Power9, the thread interrupt presenter has a different type and is
linked to the chip owning the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The boot framebuffer is expected to be configured by the firmware, so it
uses fw_cfg as interface. Initialization goes as follows:
(1) Check whenever etc/ramfb is present.
(2) Allocate framebuffer from RAM.
(3) Fill struct RAMFBCfg, write it to etc/ramfb.
Done. You can write stuff to the framebuffer now, and it should appear
automagically on the screen.
Note that this isn't very efficient because it does a full display
update on each refresh. No dirty tracking. Dirty tracking would have
to be active for the whole ram slot, so that wouldn't be very efficient
either. For a boot display which is active for a short time only this
isn't a big deal. As permanent guest display something better should be
used (if possible).
This is the ramfb core code. Some windup is needed for display devices
which want have a ramfb boot display.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20180613122948.18149-2-kraxel@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
CPUPPCState currently contains a number of fields containing the state of
the VPA. The VPA is a PAPR specific concept covering several guest/host
shared memory areas used to communicate some information with the
hypervisor.
As a PAPR concept this is really machine specific information, although it
is per-cpu, so it doesn't really belong in the core CPU state structure.
There's also other information that's per-cpu, but platform/machine
specific. So create a (void *)machine_data in PowerPCCPU which can be
used by the machine to locate per-cpu data. Intialization, lifetime and
cleanup of machine_data is entirely up to the machine type.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
Currently, we allocate space for all the cpu objects within a single core
in one big block. This was copied from an older version of the spapr code
and requires some ugly pointer manipulation to extract the individual
objects.
This design was due to a misunderstanding of qemu lifetime conventions and
has already been changed in spapr (in 94ad93bd "spapr_cpu_core: instantiate
CPUs separately".
Make an equivalent change in pnv_core to get rid of the nasty pointer
arithmetic.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
In the case where we have an interrupt generated externally from inputs to
bits 1 and 2 of port A and/or port B, it is necessary to expose
mos6522_update_irq() so it can be called by the interrupt source.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PMU device supercedes the CUDA device found on older New World Macs and
is supported by a larger number of guest OSs from OS 9 to OS X 10.5.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
MacOS 9 has a bug in its PMU driver whereby after configuring the ADB bus
devices it sends another write to reg 3 on both devices resetting them
both back to the same address.
Add a new disable_direct_reg3_writes property to ADBDevice to disable these
direct writes which can enabled just for the upcoming pmu-adb support.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PMU-enabled New World Macs expose their GPIOs via a separate memory region
within the macio device.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This option allows the VIA configuration to be controlled between 3
different possible setups: cuda, pmu-adb and pmu with USB rather than ADB
keyboard/mouse.
For the moment we don't do anything with the configuration except to pass
it to the macio device (the via-cuda parent) and also to the firmware via
the fw_cfg interface so that it can present the correct device tree.
The default is cuda which is the current default and so will have no
change in behaviour.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
- Fix options that work only with -drive or -blockdev, but not with
both, because of QDict type confusion
- rbd: Add options 'auth-client-required' and 'key-secret'
- Remove deprecated -drive options serial/addr/cyls/heads/secs/trans
- rbd, iscsi: Remove deprecated 'filename' option
- Fix 'qemu-img map' crash with unaligned image size
- Improve QMP documentation for jobs
-----BEGIN PGP SIGNATURE-----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=LxgF
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging
Block layer patches:
- Fix options that work only with -drive or -blockdev, but not with
both, because of QDict type confusion
- rbd: Add options 'auth-client-required' and 'key-secret'
- Remove deprecated -drive options serial/addr/cyls/heads/secs/trans
- rbd, iscsi: Remove deprecated 'filename' option
- Fix 'qemu-img map' crash with unaligned image size
- Improve QMP documentation for jobs
# gpg: Signature made Fri 15 Jun 2018 15:20:03 BST
# gpg: using RSA key 7F09B272C88F2FD6
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>"
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* remotes/kevin/tags/for-upstream: (26 commits)
block: Remove dead deprecation warning code
block: Remove deprecated -drive option serial
block: Remove deprecated -drive option addr
block: Remove deprecated -drive geometry options
rbd: New parameter key-secret
rbd: New parameter auth-client-required
block: Fix -blockdev / blockdev-add for empty objects and arrays
check-block-qdict: Cover flattening of empty lists and dictionaries
check-block-qdict: Rename qdict_flatten()'s variables for clarity
block-qdict: Simplify qdict_is_list() some
block-qdict: Clean up qdict_crumple() a bit
block-qdict: Tweak qdict_flatten_qdict(), qdict_flatten_qlist()
block-qdict: Simplify qdict_flatten_qdict()
block: Make remaining uses of qobject input visitor more robust
block: Factor out qobject_input_visitor_new_flat_confused()
block: Clean up a misuse of qobject_to() in .bdrv_co_create_opts()
block: Fix -drive for certain non-string scalars
block: Fix -blockdev for certain non-string scalars
qobject: Move block-specific qdict code to block-qdict.c
block: Add block-specific QDict header
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For the IoTKit MPC support, we need to wire together the
interrupt outputs of 17 MPCs; this exceeds the current
value of MAX_OR_LINES. Increase MAX_OR_LINES to 32 (which
should be enough for anyone).
The tricky part is retaining the migration compatibility for
existing OR gates; we add a subsection which is only used
for larger OR gates, and define it such that we can freely
increase MAX_OR_LINES in future (or even move to a dynamically
allocated levels[] array without an upper size limit) without
breaking compatibility.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180604152941.20374-10-peter.maydell@linaro.org
Remove the now-unused armv7m_init() function. This was a legacy from
before we properly QOMified ARMv7M, and it has some flaws:
* it combines work that needs to be done by an SoC object (creating
and initializing the TYPE_ARMV7M object) with work that needs to
be done by the board model (setting the system up to load the ELF
file specified with -kernel)
* TYPE_ARMV7M creation failure is fatal, but an SoC object wants to
arrange to propagate the failure outward
* it uses allocate-and-create via qdev_create() whereas the current
preferred style for SoC objects is to do creation in-place
Board and SoC models can instead do the two jobs this function
was doing themselves, in the right places and with whatever their
preferred style/error handling is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20180601144328.23817-3-peter.maydell@linaro.org
The -drive option serial was deprecated in QEMU 2.10. It's time to
remove it.
Tests need to be updated to set the serial number with -global instead
of using the -drive option.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Jeff Cody <jcody@redhat.com>
Here's another batch of ppc patches towards the 3.0 release. There's
a fair bit here, because I've been working through my mail backlog
after a holiday. There's not much of a central theme, amongst other
things we have:
* ppc440 / sam460ex improvements
* logging and error cleanups
* 40p (PReP) bugfixes
* Macintosh fixes and cleanups
* Add emulation of the new POWER9 store-forwarding barrier
instruction variant
* Hotplug cleanups
-----BEGIN PGP SIGNATURE-----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=g3bP
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgibson/tags/ppc-for-3.0-20180612' into staging
ppc patch queue 2018-06-12
Here's another batch of ppc patches towards the 3.0 release. There's
a fair bit here, because I've been working through my mail backlog
after a holiday. There's not much of a central theme, amongst other
things we have:
* ppc440 / sam460ex improvements
* logging and error cleanups
* 40p (PReP) bugfixes
* Macintosh fixes and cleanups
* Add emulation of the new POWER9 store-forwarding barrier
instruction variant
* Hotplug cleanups
# gpg: Signature made Tue 12 Jun 2018 07:43:21 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.0-20180612: (33 commits)
spapr_pci: Remove unhelpful pagesize warning
xics_kvm: use KVM helpers
ppc/pnv: fix LPC HC firmware address space
spapr: handle cpu core unplug via hotplug handler chain
spapr: handle pc-dimm unplug via hotplug handler chain
spapr: introduce machine unplug handler
spapr: move memory hotplug support check into spapr_memory_pre_plug()
spapr: move lookup of the node into spapr_memory_plug()
spapr: no need to verify the node
target/ppc: Allow PIR read in privileged mode
ppc4xx_i2c: Clean up and improve error logging
target/ppc: extend eieio for POWER9
mos6522: convert VMSTATE_TIMER_PTR_TEST to VMSTATE_TIMER_PTR
mos6522: move timer frequency initialisation to mos6522_reset
cuda: embed mos6522_cuda device directly rather than using QOM object link
mos6522: fix vmstate_mos6522_timer version in vmstate_mos6522
ppc: add missing FW_CFG_PPC_NVRAM_FLAT definition
ppc: remove obsolete macio_init() definition from mac.h
ppc: remove obsolete pci_pmac_init() definitions from mac.h
hw/misc/mos6522: Add trailing '\n' to qemu_log() calls
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A specific MemoryRegion is required for the LPC HC Firmware address
space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 6522 VIA timer frequency cannot be set by altering registers within the
device itself and hence it is a fixed property of the machine.
Move the initialisation of the timer frequency to the mos6522 reset function
and ensure that any subclasses always call the parent reset function so that
it isn't required to store the timer frequency within vmstate_mos6522_timer
itself.
By moving the frequency initialisation to the device reset function then we
find that the realize function for both mos6522 and mos6522_cuda becomes
obsolete and can simply be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Examining the migration stream it can be seen that the mos6522 device state is
being stored separately rather than as part of the CUDA device which is
incorrect (and likely to cause issues if another mos6522 device is added to
the machine).
Resolve this by embedding the mos6522_cuda device directly within the CUDA
device rather than using a QOM object link to reference the device separately.
Note that we also bump the version in vmstate_cuda to reflect this change: this
isn't particularly important for the moment as the Mac machine migration isn't
100% reliable due to issues migrating the timebase under TCG.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is used in OpenBIOS to define the memory layout of the NVRAM device. Whilst
currently left at its default value, add the missing definition to ensure it is
reserved.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
>From observation of various OS sources it can be seen that the token register
introduced in 4e46dcdbd3 "PPC: Newworld: Add uninorth token register" is not
required, since the only register currently implemented is the uninorth hardware
version which is read-only.
Remove the token register implementation and instead return the uninorth
version corresponding to the hardware.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Replace the "nvdimm-cap" option which took numeric arguments such as "2"
with a more user friendly "nvdimm-persistence" option which takes symbolic
arguments "cpu" or "mem-ctrl".
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Suggested-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For the case where the end_transfer_func is also the caller of
ide_transfer_start, the mutual recursion can lead to unlimited
stack usage. Introduce a new version that can be used to change
tail recursion into a loop, and use it in trace_ide_atapi_cmd_reply_end.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-8-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Now that end_transfer_func is a tail call in ahci_start_transfer,
formalize the fact that the callback (of which ahci_start_transfer is
the sole implementation) takes care of the transfer too: rename it to
pio_transfer and, if it is present, call the end_transfer_func as soon
as it returns.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180606190955.20845-4-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As of this commit, the Spec v1 is not working, and all controllers
expect the cards to be conformant to Spec v2.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20180607180641.874-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The maximum frame size includes the CRC and depends if a VLAN tag is
inserted or not. Adjust the frame size limit in the transmit handler
using on the FTGMAC100State buffer size and in the receive handler use
the packet protocol.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530061711.23673-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Specs are available here :
https://www.nxp.com/docs/en/application-note/AN264.pdf
This is a simple model supporting the basic registers for led and GPIO
mode. The device also supports two blinking rates but not the model
yet.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is an helper routine to add a single EEPROM on an I2C bus. It can
be directly used by smbus_eeprom_init() which adds a certain number of
EEPROMs on mips and x86 machines.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While we skip the GIC_INTERNAL irqs, we don't change the register offset
accordingly. This will overlap the GICR registers value and leave the
last GIC_INTERNAL irq's registers out of update.
Fix this by skipping the registers banked by GICR.
Also for migration compatibility if the migration source (old version
qemu) doesn't send gicd_no_migration_shift_bug = 1 to destination, then
we shift the data of PPI to get the right data for SPI.
Fixes: 367b9f527b
Cc: qemu-stable@nongnu.org
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Message-id: 1527816987-16108-1-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This macro isn't used by any VFIO code. And its name is
too generic. The vfio-common.h (in include/hw/vfio) can
be included by other modules in QEMU. It can introduce
conflicts.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbEXNvAAoJECgfDbjSjVRpc8gH/R8xrcFrV+k9wwbgYcOcGb6Y
LWjseE31pqJcxRV80vLOdzYEuLStZQKQQY7xBDMlA5vdyvZxIA6FLO2IsiJSbFAk
EK8pclwhpwQAahr8BfzenabohBv2UO7zu5+dqSvuJCiMWF3jGtPAIMxInfjXaOZY
odc1zY2D2EgsC7wZZ1hfraRbISBOiRaez9BoGDKPOyBY9G1ASEgxJgleFgoBLfsK
a1XU+fDM6hAVdxftfkTm0nibyf7PWPDyzqghLqjR9WXLvZP3Cqud4p8N29mY51pR
KSTjA4FYk6Z9EVMltyBHfdJs6RQzglKjxcNGdlrvacDfyFi79fGdiosVllrjfJM=
=3+V0
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
acpi, vhost, misc: fixes, features
vDPA support, fix to vhost blk RO bit handling, some include path
cleanups, NFIT ACPI table.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Jun 2018 17:25:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (31 commits)
vhost-blk: turn on pre-defined RO feature bit
ACPI testing: test NFIT platform capabilities
nvdimm, acpi: support NFIT platform capabilities
tests/.gitignore: add entry for generated file
arch_init: sort architectures
ui: use local path for local headers
qga: use local path for local headers
colo: use local path for local headers
migration: use local path for local headers
usb: use local path for local headers
sd: fix up include
vhost-scsi: drop an unused include
ppc: use local path for local headers
rocker: drop an unused include
e1000e: use local path for local headers
ioapic: fix up includes
ide: use local path for local headers
display: use local path for local headers
trace: use local path for local headers
migration: drop an unused include
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
QEMU 3.0 enables strict check for compression & decompression to
make the migration more robust, that depends on the source to fix
the internal design which triggers the unexpected error conditions
To make it work for migrating old version QEMU to 2.13 QEMU, we
introduce this parameter to disable the error check on the
destination which is the default behavior of the machine type
which is older than 2.13, alternately, the strict check can be
enabled explicitly as followings:
-M pc-q35-2.11 -global migration.decompress-error-check=true
Signed-off-by: Xiao Guangrong <xiaoguangrong@tencent.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
Read only feature shouldn't be negotiable, because if the
backend device reported Read only feature supported, QEMU
host driver shouldn't change backend's RO attribute. While
here, also enable the vhost-user-blk test utility to test
RO feature.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Add a machine command line option to allow the user to control the Platform
Capabilities Structure in the virtualized NFIT. This Platform Capabilities
Structure was added in ACPI 6.2 Errata A.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since no devices use it, we can safely remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-5-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Removal of DeviceClass::init() moved from previous patch, missing
documentation updates supplied]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-5-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
I2CSlaveClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-3-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-3-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SMBusDeviceClass::init is no more used, remove it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180419212727.26095-2-f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180528144509.15812-2-armbru@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit 5643cc94ac ("virtio-gpu-3d: add support for second capability
set (v4)") updated virtio_gpu.h with a define that does not yet(?)
exist upstream resulting in build breakage every time Linux headers
are updated via the standard update script. Conditionally define this
within QEMU code instead to avoid future breakage.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Fixes: 5643cc94ac ("virtio-gpu-3d: add support for second capability set (v4)")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180525132755.21839-2-peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-22-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-17-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Xen 4.11 has a new API to directly map guest resources. Among the resources
that can be mapped using this API are ioreq pages.
This patch modifies QEMU to attempt to use the new API should it exist,
falling back to the previous mechanism if it is unavailable.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
No declaration of "hw/vfio/vfio-common.h" directly requires to include
the "exec/address-spaces.h" header. To simplify dependencies and
ease the upcoming cleanup of "exec/address-spaces.h", directly include
it in the source file where the declaration are used.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-2-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch introduces VHOST_USER_PROTOCOL_F_HOST_NOTIFIER.
With this feature negotiated, vhost-user backend can register
memory region based host notifiers. And it will allow the guest
driver in the VM to notify the hardware accelerator at the
vhost-user backend directly.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When multi queue is enabled e.g. for a virtio-net device,
each queue pair will have a vhost_dev, and the only thing
shared between vhost devs currently is the chardev. This
patch introduces a vhost-user state structure which will
be shared by all vhost devs of the same virtio device.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces a vhost op for vhost backends to allow
them to filter the memory sections that they can handle.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Beginning of merging vDPA, new PCI ID, a new virtio balloon stat, intel
iommu rework fixing a couple of security problems (no CVEs yet), fixes
all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbBX2cAAoJECgfDbjSjVRpOEYIAIR6KGkwbAJ9SnO9B71DQHl1
yYYgM7i2HwyZ1YPnXOYWnI1lzQ1bARTf2krQJFGmfjlDaueFf9KnXdNByoVCmG8m
UhF/rQp3DcJ4wTABktPtME8gWdQxKPmDxlN5W3f29Zrm3g9S+Hshi+sfPZUkBxL4
gQMFRctb2SxvQXG+lusHVwo1oF6pzGZMmX35906he3m4xS/cfoeCP7Qj6nSvHZq7
lsLoOeYxHtXWA9gTYxpd7zW+hhUxkspoOqcXySHfO7e5enJANaulTxKuC0T+6HL4
O2iUM+1wjUYE0tQcNJ6x7emA82k5OdG2OMD6gbR1oSdquttJo7+4R+goqpb44rc=
=NUoY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
pc, pci, virtio, vhost: fixes, features
Beginning of merging vDPA, new PCI ID, a new virtio balloon stat, intel
iommu rework fixing a couple of security problems (no CVEs yet), fixes
all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 23 May 2018 15:41:32 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (28 commits)
intel-iommu: rework the page walk logic
util: implement simple iova tree
intel-iommu: trace domain id during page walk
intel-iommu: pass in address space when page walk
intel-iommu: introduce vtd_page_walk_info
intel-iommu: only do page walk for MAP notifiers
intel-iommu: add iommu lock
intel-iommu: remove IntelIOMMUNotifierNode
intel-iommu: send PSI always even if across PDEs
nvdimm: fix typo in label-size definition
contrib/vhost-user-blk: enable protocol feature for vhost-user-blk
hw/virtio: Fix brace Werror with clang 6.0.0
libvhost-user: Send messages with no data
vhost-user+postcopy: Use qemu_set_nonblock
virtio: support setting memory region based host notifier
vhost-user: support receiving file descriptors in slave_read
vhost-user: add Net prefix to internal state structure
linux-headers: add kvm header for mips
linux-headers: add unistd.h on all arches
update-linux-headers.sh: unistd.h, kvm consistency
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+YI
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/sstabellini-http/tags/xen-20180522-tag' into staging
Xen 2018/05/22
# gpg: Signature made Tue 22 May 2018 19:44:06 BST
# gpg: using RSA key 894F8F4870E1AE90
# gpg: Good signature from "Stefano Stabellini <stefano.stabellini@eu.citrix.com>"
# gpg: aka "Stefano Stabellini <sstabellini@kernel.org>"
# Primary key fingerprint: D04E 33AB A51F 67BA 07D3 0AEA 894F 8F48 70E1 AE90
* remotes/sstabellini-http/tags/xen-20180522-tag:
xen_disk: be consistent with use of xendev and blkdev->xendev
xen_disk: use a single entry iovec
xen_backend: make the xen_feature_grant_copy flag private
xen_disk: remove use of grant map/unmap
xen_backend: add an emulation of grant copy
xen: remove other open-coded use of libxengnttab
xen_disk: remove open-coded use of libxengnttab
xen_backend: add grant table helpers
xen: add a meaningful declaration of grant_copy_segment into xen_common.h
checkpatch: generalize xen handle matching in the list of types
xen-hvm: create separate function for ioreq server initialization
xen_pt: Present the size of 64 bit BARs correctly
configure: Add explanation for --enable-xen-pci-passthrough
xen/pt: use address_space_memory object for memory region hooks
xen-pvdevice: Introduce a simplistic xen-pvdevice save state
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create a new header file, move the bochs vbe dispi interface
defines to it, so they can be used outside vga code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20180522165058.15404-2-kraxel@redhat.com
This patch fixes a potential small window that the DMA page table might
be incomplete or invalid when the guest sends domain/context
invalidations to a device. This can cause random DMA errors for
assigned devices.
This is a major change to the VT-d shadow page walking logic. It
includes but is not limited to:
- For each VTDAddressSpace, now we maintain what IOVA ranges we have
mapped and what we have not. With that information, now we only send
MAP or UNMAP when necessary. Say, we don't send MAP notifies if we
know we have already mapped the range, meanwhile we don't send UNMAP
notifies if we know we never mapped the range at all.
- Introduce vtd_sync_shadow_page_table[_range] APIs so that we can call
in any places to resync the shadow page table for a device.
- When we receive domain/context invalidation, we should not really run
the replay logic, instead we use the new sync shadow page table API to
resync the whole shadow page table without unmapping the whole
region. After this change, we'll only do the page walk once for each
domain invalidations (before this, it can be multiple, depending on
number of notifiers per address space).
While at it, the page walking logic is also refactored to be simpler.
CC: QEMU Stable <qemu-stable@nongnu.org>
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Tested-by: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For UNMAP-only IOMMU notifiers, we don't need to walk the page tables.
Fasten that procedure by skipping the page table walk. That should
boost performance for UNMAP-only notifiers like vhost.
CC: QEMU Stable <qemu-stable@nongnu.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SECURITY IMPLICATION: this patch fixes a potential race when multiple
threads access the IOMMU IOTLB cache.
Add a per-iommu big lock to protect IOMMU status. Currently the only
thing to be protected is the IOTLB/context cache, since that can be
accessed even without BQL, e.g., in IO dataplane.
Note that we don't need to protect device page tables since that's fully
controlled by the guest kernel. However there is still possibility that
malicious drivers will program the device to not obey the rule. In that
case QEMU can't really do anything useful, instead the guest itself will
be responsible for all uncertainties.
CC: QEMU Stable <qemu-stable@nongnu.org>
Reported-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
That is not really necessary. Removing that node struct and put the
list entry directly into VTDAddressSpace. It simplfies the code a lot.
Since at it, rename the old notifiers_list into vtd_as_with_notifiers.
CC: QEMU Stable <qemu-stable@nongnu.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Fixes: commit da6789c27c ("nvdimm: add a macro for property "label-size"")
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Cc: Haozhong Zhang <haozhong.zhang@intel.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch introduces the support for setting memory region
based host notifiers for virtio device. This is helpful when
using a hardware accelerator for a virtio device, because
hardware heavily depends on the notification, this will allow
the guest driver in the VM to notify the hardware directly.
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There is no longer any use of this flag outside of the xen_backend code.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony Perard <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
This patch adds grant table helper functions to the xen_backend code to
localize error reporting and use of xen_domid.
The patch also defers the call to xengnttab_open() until just before the
initialise method in XenDevOps is invoked. This method is responsible for
mapping the shared ring. No prior method requires access to the grant table.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Currently the xen_disk source has to carry #ifdef exclusions to compile
against Xen older then 4.8. This is a bit messy so this patch lifts the
definition of struct xengnttab_grant_copy_segment and adds it into the
pre-4.8 compat area in xen_common.h, which allows xen_disk to be cleaned
up.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
There is no need to include pci.h in these files.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The ZynqMP contains two instances of a generic DMA, the GDMA, located in the
FPD (full power domain), and the ADMA, located in LPD (low power domain). This
patch adds these two DMAs to the ZynqMP board.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180503214201.29082-3-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of the generic DMA found on Xilinx ZynqMP.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180503214201.29082-2-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The property legacy-cache will be used to control the cache information.
If user passes "-cpu legacy-cache" then older information will
be displayed even if the hardware supports new information. Otherwise
use the statically loaded cache definitions if available.
Renamed the previous cache structures to legacy_*. If there is any change in
the cache information, then it needs to be initialized in builtin_x86_defs.
Signed-off-by: Babu Moger <babu.moger@amd.com>
Tested-by: Geoffrey McRae <geoff@hostfission.com>
Message-Id: <20180514164156.27034-3-babu.moger@amd.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This fixes an issue by adding bounds checking to multi-byte packets
where the PS/2 mouse data stream may become corrupted due to data being
discarded when the PS/2 ringbuffer is full.
Interrupts for Multi-byte responses are postponed until the final byte
has been queued.
These changes fix a bug where windows guests drop the mouse device
entirely requring the guest to be restarted.
Signed-off-by: Geoffrey McRae <geoff@hostfission.com>
Message-Id: <20180507150310.2FEA0381924@moya.office.hostfission.com>
[ kraxel: codestyle fixes ]
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Calling pause_all_vcpus()/resume_all_vcpus() from a VCPU thread might
not be the best idea. As pause_all_vcpus() temporarily drops the qemu
mutex, two parallel calls to pause_all_vcpus() can be active at a time,
resulting in a deadlock. (either by two VCPUs or by the main thread and a
VCPU)
Let's handle it via the main loop instead, as suggested by Paolo. If we
would have two parallel reset requests by two different VCPUs at the
same time, the last one would win.
We use the existing ipl device to handle it. The nice side effect is
that we can get rid of reipl_requested.
This change implies that all reset handling now goes via the common
path, so "no-reboot" handling is now active for all kinds of reboots.
Let's execute any CPU initialization code on the target CPU using
run_on_cpu.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180424101859.10239-1-david@redhat.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Version: GnuPG v1
iQEcBAABAgAGBQJa+UAZAAoJEO8Ells5jWIRTJIIAIcpNROupxHEfcAQKU7lIqys
qx/FxKp+lknzzQMwUfmZwT3PuBD+tWuE7ugXgzjVulvE11F+Z3QBPTDBtOObaMa1
qpgIF3zzrNxtuWMc/72Q8/wEE1wtBUo+WTAGw9Xp1dVomYOOsg1wa7dsKdZhRfz7
nIwDW2ftw3/mx+uTW2/a163v+IDDL9L+HOLibQHWUxOMM39ASchiqAXLF4mfhpwH
xr0OPd7wtcmrDsD/CLbdkGCJ/+vsXnY8pzNmy1RjJuDpWpqlgYpJJPtLBfXBo9VA
91sz5+KryzjpXXzKcQuhiU020O1dIKIe3PWqK6z0x0UjtZ1Yox5adZ3eFomHHwU=
=bIws
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging
# gpg: Signature made Mon 14 May 2018 08:51:53 BST
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net: Get rid of 'vlan' terminology and use 'hub' instead in the doc files
net: Get rid of 'vlan' terminology and use 'hub' instead in the source files
net: Remove the deprecated "vlan" parameter
net: Fix memory leak in net_param_nic()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It's been marked as deprecated since QEMU v2.9.0, so that should have
been enough time for everybody to either just drop unnecessary "vlan=0"
parameters, to switch to the modern -device + -netdev syntax for connecting
guest NICs with host network backends, or to switch to the "hubport" netdev
in case hubs are really wanted instead.
Buglink: https://bugs.launchpad.net/qemu/+bug/658904
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
load_dtb() depends on arm_load_kernel() to figure out place
in RAM where it should be loaded, but it's not required for
arm_load_kernel() to work. Sometimes it's neccesary for
devices added with -device/device_add to be enumerated in
DTB as well, which's lead to [1] and surrounding commits to
add 2 more machine_done notifiers with non obvious ordering
to make dynamic sysbus devices initialization happen in
the right order.
However instead of moving whole arm_load_kernel() in to
machine_done, it's sufficient to move only load_dtb() into
virt_machine_done() notifier and remove ArmLoadKernelNotifier/
/PlatformBusFDTNotifierParams notifiers, which saves us ~90LOC
and simplifies code flow quite a bit.
Later would allow to consolidate DTB generation within one
function for 'mach-virt' board and make it reentrant so it
could generate updated DTB in device hotplug secenarios.
While at it rename load_dtb() to arm_load_dtb() since it's
public now.
Add additional field skip_dtb_autoload to struct arm_boot_info
to allow manual DTB load later in mach-virt and to avoid touching
all other boards to explicitly call arm_load_dtb().
1) (ac9d32e hw/arm/boot: arm_load_kernel implemented as a machine init done notifier)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1525691524-32265-4-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
platform-bus were using machine_done notifier to get and map
(assign irq/mmio resources) dynamically added sysbus devices
after all '-device' options had been processed.
That however creates non obvious dependencies on ordering of
machine_done notifiers and requires carefull line juggling
to keep it working. For example see comment above
create_platform_bus() and 'straitforward' arm_load_kernel()
had to converted to machine_done notifier and that lead to
yet another machine_done notifier to keep it working
arm_register_platform_bus_fdt_creator().
Instead of hiding resource assignment in platform-bus-device
to magically initialize sysbus devices, use device plug
callback and assign resources explicitly at board level
at the moment each -device option is being processed.
That adds a bunch of machine declaration boiler plate to
e500plat board, similar to ARM/x86 but gets rid of hidden
machine_done notifier and would allow to remove the dependent
notifiers in ARM code simplifying it and making code flow
easier to follow.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 1525691524-32265-3-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By default MachineClass::get_hotplug_handler is NULL and concrete board
should set it to it's own handler.
Considering there isn't any default handler, drop saving empty
MachineClass::get_hotplug_handler in child class and make PC code
consistent with spapr/s390x boards.
We can bring this back when actual usecase surfaces and do it
consistently across boards that use get_hotplug_handler().
Suggested-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-id: 1525691524-32265-2-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* pc-dimm: factor out MemoryDevice
(virtio-pmem and virtio-mem will make use of the new abstraction later)
* scripts/device-crash-test: Removed fixed CAN entries
-----BEGIN PGP SIGNATURE-----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=Hhge
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/ehabkost/tags/machine-next-pull-request' into staging
Machine queue, 2018-05-07
* pc-dimm: factor out MemoryDevice
(virtio-pmem and virtio-mem will make use of the new abstraction later)
* scripts/device-crash-test: Removed fixed CAN entries
# gpg: Signature made Mon 07 May 2018 18:01:42 BST
# gpg: using RSA key 2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/machine-next-pull-request:
scripts/device-crash-test: Removed fixed CAN entries
vl: allow 'maxmem' without 'slot'
spapr: rename "hotplug memory" terminology to "device memory"
pc: rename "hotplug memory" terminology to "device memory"
machine: rename MemoryHotplugState to DeviceMemoryState
pc-dimm: move actual plug/unplug of a memory region to MemoryDevice
pc-dimm: factor out capacity and slot checks into MemoryDevice
pc-dimm: factor out address search into MemoryDevice code
pc-dimm: pass in the machine and to the MemoryHotplugState
pc-dimm: no need to pass the memory region
machine: make MemoryHotplugState accessible via the machine
pc-dimm: factor out MemoryDevice interface
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Several code cleanups, minor specification conformance changes,
fixes to make ROM read-only and add device-tree size checks.
* Honour privileged ISA v1.10 counter enable CSRs.
* Implements WARL behavior for CSRs that don't support writes
* Past behavior of raising traps was non-conformant
with the RISC-V Privileged ISA Specification v1.10.
* Allow S-mode access to sstatus.MXR when priv ISA >= v1.10
* Sets mtval/stval to zero on exceptions without addresses
* Past behavior of leaving the last value was non-conformant
with the RISC-V Privileged ISA Specition v1.10. mtval/stval
must be set on all exceptions; to zero if not supported.
* Make ROMs read-only and implement device-tree size checks
* Uses memory_region_init_rom and rom_add_blob_fixed_as
* Adds hexidecimal instruction bytes to disassembly output.
* Fixes missing break statement for rv128 disassembly.
* Several code cleanups
* Replacing hard-coded constants with enums
* Dead-code elimination
This is an incremental pull that contains 20 reviewed changes out
of 38 changes currently queued in the qemu-2.13-for-upstream branch.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQR8mZMOsXzYugc9Xvpr8dezV+8+TwUCWu496QAKCRBr8dezV+8+
T1ZEAJ4wQRHZtn4suN5yMEHQMA2FkX1iNACgiYWLtcNcgoa88eaTcJJJu4QZryY=
=I2wf
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riscv/tags/riscv-qemu-2.13-pull-20180506' into staging
RISC-V: QEMU 2.13 Privileged ISA emulation updates
Several code cleanups, minor specification conformance changes,
fixes to make ROM read-only and add device-tree size checks.
* Honour privileged ISA v1.10 counter enable CSRs.
* Implements WARL behavior for CSRs that don't support writes
* Past behavior of raising traps was non-conformant
with the RISC-V Privileged ISA Specification v1.10.
* Allow S-mode access to sstatus.MXR when priv ISA >= v1.10
* Sets mtval/stval to zero on exceptions without addresses
* Past behavior of leaving the last value was non-conformant
with the RISC-V Privileged ISA Specition v1.10. mtval/stval
must be set on all exceptions; to zero if not supported.
* Make ROMs read-only and implement device-tree size checks
* Uses memory_region_init_rom and rom_add_blob_fixed_as
* Adds hexidecimal instruction bytes to disassembly output.
* Fixes missing break statement for rv128 disassembly.
* Several code cleanups
* Replacing hard-coded constants with enums
* Dead-code elimination
This is an incremental pull that contains 20 reviewed changes out
of 38 changes currently queued in the qemu-2.13-for-upstream branch.
# gpg: Signature made Sun 06 May 2018 00:27:37 BST
# gpg: using DSA key 6BF1D7B357EF3E4F
# gpg: Good signature from "Michael Clark <michaeljclark@mac.com>"
# gpg: aka "Michael Clark <mjc@sifive.com>"
# gpg: aka "Michael Clark <michael@metaparadigm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 7C99 930E B17C D8BA 073D 5EFA 6BF1 D7B3 57EF 3E4F
* remotes/riscv/tags/riscv-qemu-2.13-pull-20180506:
RISC-V: Mark ROM read-only after copying in code
RISC-V: No traps on writes to misa,minstret,mcycle
RISC-V: Make mtvec/stvec ignore vectored traps
RISC-V: Add mcycle/minstret support for -icount auto
RISC-V: Use [ms]counteren CSRs when priv ISA >= v1.10
RISC-V: Allow S-mode mxr access when priv ISA >= v1.10
RISC-V: Clear mtval/stval on exceptions without info
RISC-V: Hardwire satp to 0 for no-mmu case
RISC-V: Update E and I extension order
RISC-V: Remove erroneous comment from translate.c
RISC-V: Remove EM_RISCV ELF_MACHINE indirection
RISC-V: Make virt header comment title consistent
RISC-V: Make some header guards more specific
RISC-V: Fix missing break statement in disassembler
RISC-V: Include instruction hex in disassembly
RISC-V: Remove unused class definitions
RISC-V: Remove identity_translate from load_elf
RISC-V: Use ROM base address and size from memmap
RISC-V: Make virt board description match spike
RISC-V: Replace hardcoded constants with enum values
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's make it clear at relevant places that we are dealing with device
memory. That it can be used for memory hotplug is just a special case.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-11-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
[ehabkost: rebased series, solved conflicts at spapr.c]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Let's make it clear that we are dealing with device memory. That it can
be used for memory hotplug is just a special case.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-10-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Rename it to better match the new terminology.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-9-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Registering the memory region for migration has do be done by the owner.
There could be cases, where we don't want to migrate the memory.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-8-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Move the checks into memory_device_get_free_addr(). This will check
before doing any calculations if we have KVM/vhost slots left and if
the total region size would be exceeded.
Of course, while at it, make it independent of pc-dimm code.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-7-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
This mainly moves code, but does a handfull of optimizations:
- We pass the machine instead of the address space properties
- We check the hinted address directly and handle fragmented memory
better
- We make the search independent of pc-dimm
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-6-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We use the machine internally either way, so let's just pass it in then.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-5-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
We can just query it ourselves. When unplugging, we should always be
able to the region (as it was previously plugged). E.g. PPC already
assumed that and used &error_abort.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-4-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Let's allow to query the MemoryHotplugState directly from the machine.
If the pointer is NULL, the machine does not support memory devices. If
the pointer is !NULL, the machine supports memory devices and the
data structure contains information about the applicable physical
guest address space region.
This allows us to generically detect if a certain machine has support
for memory devices, and to generically manage it (find free address
range, plug/unplug a memory region).
We will rename "MemoryHotplugState" to something more meaningful
("DeviceMemory") after we completed factoring out the pc-dimm code into
MemoryDevice code.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-3-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
[ehabkost: rebased series, solved conflicts at spapr.c]
[ehabkost: squashed fix to use g_malloc0()]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
On the qmp level, we already have the concept of memory devices:
"query-memory-devices"
Right now, we only support NVDIMM and PCDIMM.
We want to map other devices later into the address space of the guest.
Such device could e.g. be virtio devices. These devices will have a
guest memory range assigned but won't be exposed via e.g. ACPI. We want
to make them look like memory device, but not glued to pc-dimm.
Especially, it will not always be possible to have TYPE_PC_DIMM as a parent
class (e.g. virtio devices). Let's use an interface instead. As a first
part, convert handling of
- qmp_pc_dimm_device_list
- get_plugged_memory_size
to our new model. plug/unplug stuff etc. will follow later.
A memory device will have to provide the following functions:
- get_addr(): Necessary, as the property "addr" can e.g. not be used for
virtio devices (already defined).
- get_plugged_size(): The amount this device offers to the guest as of
now.
- get_region_size(): Because this can later on be bigger than the
plugged size.
- fill_device_info(): Fill MemoryDeviceInfo, e.g. for qmp.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180423165126.15441-2-david@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Removes a whole lot of unnecessary boilerplate code. Machines
don't need to be objects. The expansion of the SOC object model
for the RISC-V machines will happen in the future as SiFive
plans to add their FE310 and FU540 SOCs to QEMU. However, it
seems that this present boilerplate is complete unnecessary.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Another case of replacing hard coded constants, this time
referring to the definition in the virt machine's memmap.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V device-tree code has a number of hard-coded
constants and this change moves them into header enums.
Cc: Sagar Karandikar <sagark@eecs.berkeley.edu>
Cc: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Michael Clark <mjc@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
This patch builds the smmuv3 node in the ACPI IORT table.
The RID space of the root complex, which spans 0x0-0x10000
maps to streamid space 0x0-0x10000 in smmuv3, which in turn
maps to deviceid space 0x0-0x10000 in the ITS group.
The guest must feature the IOMMU probe deferral series
(https://lkml.org/lkml/2017/4/10/214) which fixes streamid
multiple lookup. This bug is not related to the SMMU emulation.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Message-id: 1524665762-31355-14-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add code to instantiate an smmuv3 in virt machine. A new iommu
integer member is introduced in VirtMachineState to store the type
of the iommu in use.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-13-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements a skeleton for the smmuv3 device.
Datatypes and register definitions are introduced. The MMIO
region, the interrupts and the queue are initialized.
Only the MMIO read operation is implemented here.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the page table walk for VMSAv8-64.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Message-id: 1524665762-31355-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We set up the infrastructure to enumerate all the PCI devices
attached to the SMMU and create an associated IOMMU memory
region and address space.
Those info are stored in SMMUDevice objects. The devices are
grouped according to the PCIBus they belong to. A hash table
indexed by the PCIBus pointer is used. Also an array indexed by
the bus number allows to find the list of SMMUDevices.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The patch introduces the smmu base device and class for the ARM
smmu. Devices for specific versions will be derived from this
base device.
We also introduce some important datatypes.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- new machine type
- extend SCLP event masks
- support configuration of consoles via -serial
- firmware improvements: non-sequential entries in boot menu, support
for indirect loading via .INS files in s390-netboot
- bugfixes and cleanups
-----BEGIN PGP SIGNATURE-----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=cYvD
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20180504' into staging
First s390x pull request for 2.13.
- new machine type
- extend SCLP event masks
- support configuration of consoles via -serial
- firmware improvements: non-sequential entries in boot menu, support
for indirect loading via .INS files in s390-netboot
- bugfixes and cleanups
# gpg: Signature made Fri 04 May 2018 08:19:57 BST
# gpg: using RSA key DECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cohuck@redhat.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20180504:
pc-bios/s390: Update firmware images
s390-ccw: force diag 308 subcode to unsigned long
pc-bios/s390-ccw/net: Add support for .INS config files
pc-bios/s390-ccw/net: Use diag308 to reset machine before jumping to the OS
pc-bios/s390-ccw/net: Split up net_load() into init, load and release parts
pc-bios/s390-ccw: fix non-sequential boot entries (enum)
pc-bios/s390-ccw: fix non-sequential boot entries (eckd)
pc-bios/s390-ccw: fix loadparm initialization and int conversion
pc-bios/s390-ccw: rename MAX_TABLE_ENTRIES to MAX_BOOT_ENTRIES
pc-bios/s390-ccw: size_t should be unsigned
hw/s390x: Allow to configure the consoles with the "-serial" parameter
s390x/kvm: cleanup calls to cpu_synchronize_state()
vfio-ccw: introduce vfio_ccw_get_device()
s390x/sclp: extend SCLP event masks to 64 bits
s390x: introduce 2.13 compat machine
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since the macio device has a link to the PIC device, we can now wire up the
IRQs directly via qdev GPIOs rather than having to use an intermediate array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Commit 4e46dcdbd3 "PPC: Newworld: Add uninorth token register" added a TODO
which was to convert the uninorth registers hack to a proper device. Move
these registers to a new uninorth device, removing the old hacks from
mac_newworld.c.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Under PAPR, only the boot CPU is active when the system starts. Other cpus
must be explicitly activated using an RTAS call. The entry state for the
boot and secondary cpus isn't identical, but it has some things in common.
We're going to add a bit more common setup later, too, so to simplify
make a helper which sets up the common entry state for both boot and
secondary cpu threads.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
The consoles ("sclpconsole" and "sclplmconsole") can only be configured
with "-device" and "-chardev" so far. Other machines use the convenience
option "-serial" to configure the default consoles, even for virtual
consoles like spapr-vty on the pseries machine. So let's support this
option on s390x, too. This way we can easily enable the serial console
here again with "-nodefaults", for example:
qemu-system-s390x -no-shutdown -nographic -nodefaults -serial mon:stdio
... which is way shorter than typing:
qemu-system-s390x -no-shutdown -nographic -nodefaults \
-chardev stdio,id=c1,mux=on -device sclpconsole,chardev=c1 \
-mon chardev=c1
The -serial parameter can also be used if you only want to see the QEMU
monitor on stdio without using -nodefaults, but not the console output.
That's something that is pretty impossible with the current code today:
qemu-system-s390x -no-shutdown -nographic -serial none
While we're at it, this patch also maps the second -serial option to the
"sclplmconsole", so that there is now an easy way to configure this second
console on s390x, too, for example:
qemu-system-s390x -no-shutdown -nographic -serial null -serial mon:stdio
Additionally, the new code is also smaller than the old one and we have
less s390x-specific code in vl.c :-)
I've also checked that migration still works as expected by migrating
a guest with console output back and forth between a qemu-system-s390x
that has this patch and an instance without this patch.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1524754794-28005-1-git-send-email-thuth@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Extend the SCLP event masks to 64 bits.
Notice that using any of the new bits results in a state that cannot be
migrated to an older version.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Message-Id: <1520507069-22179-1-git-send-email-imbrenda@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The new property ibm,dynamic-memory-v2 allows memory to be represented
in a more compact manner in device tree.
Signed-off-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
As a rule we prefer to pass PowerPCCPU instead of CPUPPCState, and this
change will make some things simpler later on.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
The existing UNINState actually represents the PCI/AGP host bridge stage so
rename it accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Do this for both the uninorth main and uninorth u3 AGP buses, using the main
PCI bus for each machine (this ensures the IO addresses still match those
used by OpenBIOS).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Now that the OpenPIC is wired up via the board, we can now remove our temporary
PIC qdev pointer property and replace it with an object link instead.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is in preparation for moving the PCI bus wiring inside the uninorth
host bridge devices. In the future it will be possible to remove this once the
PICs have been switched to use qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since the macio device has a link to the PIC device, we can now wire up the
IRQs directly via qdev GPIOs rather than having to use an intermediate array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Instead wire up heathrow to the CPU and grackle PCI host using qdev GPIOs.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
[dwg: Added hw/hw.h #include as suggested by Philippe Mathieu-Daudé]
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The last user was just removed; remove this function, accordingly.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Xen unstable (to be in 4.11) has two new dmops, relocate_memory and
pin_memory_cacheattr. Use these to set up the VGA memory, replacing the
previous calls to libxc. This allows the VGA console to work properly
when QEMU is running restricted (-xen-domid-restrict).
Wrapper functions are provided to allow QEMU to work with older versions
of Xen.
Tweak the error handling while making this change:
* Report pin_memory_cacheattr errors.
* Report errors even when DEBUG_HVM is not set. This is useful for
trying to understand why VGA is not working, since otherwise it just
fails silently.
* Fix the return values when an error occurs. The functions now
consistently return -1 and set errno.
CC: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Ian Jackson <ian.jackson@eu.citrix.com>
Signed-off-by: Ian Jackson <ian.jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
xc_interface_open etc. is not going to work if we have dropped
privilege, but xendevicemodel_shutdown will if everything is new
enough.
xendevicemodel_shutdown is only availabe in Xen 4.10 and later, so
provide a stub for earlier versions.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
We are going to want to use the dummy xendevicemodel_handle type in
new stub functions in the CONFIG_XEN_CTRL_INTERFACE_VERSION < 41000
section. So we need to provide that definition, or (as applicable)
include the appropriate header, earlier in the file.
(Ideally the newer compatibility layers would be at the bottom of the
file, so that they can naturally benefit from the compatibility layers
for earlier version. But that's rather too much for this series.)
No functional change.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
And insist that it works.
Drop individual use of xendevicemodel_restrict and
xenforeignmemory_restrict. These are not actually effective in this
version of qemu, because qemu has a large number of fds open onto
various Xen control devices.
The restriction arrangements are still not right, because the
restriction needs to be done very late - after qemu has opened all of
its control fds.
xentoolcore_restrict_all and xentoolcore.h are available in Xen 4.10
and later, only. Provide a compatibility stub. And drop the
compatibility stubs for the old functions.
Signed-off-by: Ian Jackson <Ian.Jackson@eu.citrix.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
The superio device has a limit on the number of serial
ports it supports which is really only there because
it has a fixed-size array serial[]. This limit isn't
related particularly to the global MAX_SERIAL_PORTS limit,
so use a different #define for it.
(In practice the users of superio only ever want 2 serial ports.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-12-peter.maydell@linaro.org
The ISA serial port handling in serial-isa.c imposes a limit
of 4 serial ports. This is because we only know of 4 IO port
and IRQ settings for them, and is unrelated to the generic
MAX_SERIAL_PORTS limit, though they happen to both be set at
4 currently.
Use a new MAX_ISA_SERIAL_PORTS wherever that is the correct
limit to be checking against.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-11-peter.maydell@linaro.org
Turn the newly added subsection off for old machine types
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
We would like to have different behavior for passthrough devices
depending on the SCSI version they expose. To prepare for that,
allow the user of emulated devices to specify the desired SCSI
level, and adjust the emulation according to the property value.
The next patch will set the level for scsi-block and scsi-generic
devices.
Based on a patch by Daniel Henrique Barboza
<danielhb@linux.vnet.ibm.com>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Instead of using "1.0" as the system version of SMBIOS, we should use
mc->name for mach-virt machine type to be consistent other architectures.
With this patch, "dmidecode -t 1" (e.g., "-M virt-2.12,accel=kvm") will
show:
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: QEMU
Product Name: KVM Virtual Machine
Version: virt-2.12
Serial Number: Not Specified
...
instead of:
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: QEMU
Product Name: KVM Virtual Machine
Version: 1.0
Serial Number: Not Specified
...
For backward compatibility, we allow older machine types to keep "1.0"
as the default system version.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20180322212318.7182-1-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Linux does not detect a break from this IMX serial driver as a magic
sysrq. Nor does it note a break in the port error counts.
The former is because the Linux driver uses the BRCD bit in the USR2
register to trigger the RS-232 break handler in the kernel, which is
where sysrq hooks in. The emulated UART was not setting this status
bit.
The latter is because the Linux driver expects, in addition to the BRK
bit, that the ERR bit is set when a break is read in the FIFO. A break
should also count as a frame error, so add that bit too.
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Message-id: 20180320013657.25038-1-tpiepho@impinj.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Make qmp_pc_dimm_device_list() return sorted by start address
list of devices so that it could be reused in places that
would need sorted list*. Reuse existing pc_dimm_built_list()
to get sorted list.
While at it hide recursive callbacks from callers, so that:
qmp_pc_dimm_device_list(qdev_get_machine(), &list);
could be replaced with simpler:
list = qmp_pc_dimm_device_list();
* follow up patch will use it in build_srat()
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> for ppc part
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
All PCI devices are now QOM'ified.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The bcm2837 is pretty similar to the bcm2836, but it does have
some differences. Notably, the MPIDR affinity aff1 values it
sets for the CPUs are 0x0, rather than the 0xf that the bcm2836
uses, and if this is wrong Linux will not boot.
Rather than trying to have one device with properties that
configure it differently for the two cases, create two
separate QOM devices for the two SoCs. We use the same approach
as hw/arm/aspeed_soc.c and share code and have a data table
that might differ per-SoC. For the moment the two types don't
actually have different behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-7-peter.maydell@linaro.org
Our BCM2836 type is really a generic one that can be any of
the bcm283x family. Rename it accordingly. We change only
the names which are visible via the header file to the
rest of the QEMU code, leaving private function names
in bcm2836.c as they are.
This is a preliminary to making bcm283x be an abstract
parent class to specific types for the bcm2836 and bcm2837.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-6-peter.maydell@linaro.org
Add support for "TX complete"/TXDC interrupt generate by real HW since
it is needed to support guests other than Linux.
Based on the patch by Bill Paul as found here:
https://bugs.launchpad.net/qemu/+bug/1753314
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: Bill Paul <wpaul@windriver.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Bill Paul <wpaul@windriver.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Message-id: 20180315191141.6789-2-andrew.smirnov@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The sabrelite machine model used by qemu-system-arm is based on the
Freescale/NXP i.MX6Q processor. This SoC has an on-board ethernet
controller which is supported in QEMU using the imx_fec.c module
(actually called imx.enet for this model.)
The include/hw/arm/fsm-imx6.h file defines the interrupt vectors for the
imx.enet device like this:
#define FSL_IMX6_ENET_MAC_1588_IRQ 118
#define FSL_IMX6_ENET_MAC_IRQ 119
According to https://www.nxp.com/docs/en/reference-manual/IMX6DQRM.pdf,
page 225, in Table 3-1. ARM Cortex A9 domain interrupt summary,
interrupts are as follows.
150 ENET MAC 0 IRQ
151 ENET MAC 0 1588 Timer interrupt
where
150 - 32 == 118
151 - 32 == 119
In other words, the vector definitions in the fsl-imx6.h file are reversed.
Fixing the interrupts alone causes problems with older Linux kernels:
The Ethernet interface will fail to probe with Linux v4.9 and earlier.
Linux v4.1 and earlier will crash due to a bug in Ethernet driver probe
error handling. This is a Linux kernel problem, not a qemu problem:
the Linux kernel only worked by accident since it requested both interrupts.
For backward compatibility, generate the Ethernet interrupt on both interrupt
lines. This was shown to work from all Linux kernel releases starting with
v3.16.
Link: https://bugs.launchpad.net/qemu/+bug/1753309
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 1520723090-22130-1-git-send-email-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With all targets defining CPU_RESOLVING_TYPE, refactor
cpu_parse_cpu_model(type, cpu_model) to parse_cpu_model(cpu_model)
so that callers won't have to know internal resolving cpu
type. Place it in exec.c so it could be called from both
target independed vl.c and *-user/main.c.
That allows us to stop abusing cpu type from
MachineClass::default_cpu_type
as resolver class in vl.c which were confusing part of
cpu_parse_cpu_model().
Also with new parse_cpu_model(), the last users of cpu_init()
in null-machine.c and bsd/linux-user targets could be switched
to cpu_create() API and cpu_init() API will be removed by
follow up patch.
With no longer users left remove MachineState::cpu_model field,
new code should use MachineState::cpu_type instead and
leave cpu_model parsing to generic code in vl.c.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1518000027-274608-5-git-send-email-imammedo@redhat.com>
[ehabkost: Fix bsd-user build error]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
The global hack for creating SCSI devices has recently been removed,
but this apparently broke SCSI devices on some boards that were not
ready for this change yet. For the 40p machine you now get:
$ ppc64-softmmu/qemu-system-ppc64 -M 40p -cdrom x.iso
qemu-system-ppc64: -cdrom x.iso: machine type does not support if=scsi,bus=0,unit=2
Fix it by providing a lsi53c810_create() function that takes care
of calling scsi_bus_legacy_handle_cmdline() after creating the
corresponding SCSI controller.
Fixes: 1454509726
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Wang Xin <wangxinxin.wang@huawei.com>
Message-Id: <1517367668-25048-1-git-send-email-wangxinxin.wang@huawei.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJapqaMAAoJEL/70l94x66DQoUH/Rvg+a8giz/SrEA4P8D3Cb2z
4GNbNUUoy4oU0ltD5IAMskMwpOsvl1batE0D+pKIlfO9NV4+Cj2kpgo0p9TxoYqM
VCby3wRtx27zb5nVytC6M++iIKXmeEMqXmFw61I6umddNPSl4IR3hiHEE0DM+7dV
UPIOvJeEiazyQaw3Iw+ZctNn8dDBKc/+6oxP9xRcYTaZ6hB4G9RZkqGNNSLcJkk7
R0UotdjzIZhyWMOkjIwlpTF4sWv8gsYUV4bPYKMYho5B0Obda2dBM3I1kpA8yDa/
xZ5lheOaAVBZvM5aMIcaQPa65MO9hLyXFmhMOgyfpJhLBBz6Qpa4OLLI6DeTN+0=
=UAgA
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into staging
* Record-replay lockstep execution, log dumper and fixes (Alex, Pavel)
* SCSI fix to pass maximum transfer size (Daniel Barboza)
* chardev fixes and improved iothread support (Daniel Berrangé, Peter)
* checkpatch tweak (Eric)
* make help tweak (Marc-André)
* make more PCI NICs available with -net or -nic (myself)
* change default q35 NIC to e1000e (myself)
* SCSI support for NDOB bit (myself)
* membarrier system call support (myself)
* SuperIO refactoring (Philippe)
* miscellaneous cleanups and fixes (Thomas)
# gpg: Signature made Mon 12 Mar 2018 16:10:52 GMT
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (69 commits)
tcg: fix cpu_io_recompile
replay: update documentation
replay: save vmstate of the asynchronous events
replay: don't process async events when warping the clock
scripts/replay-dump.py: replay log dumper
replay: avoid recursive call of checkpoints
replay: check return values of fwrite
replay: push replay_mutex_lock up the call tree
replay: don't destroy mutex at exit
replay: make locking visible outside replay code
replay/replay-internal.c: track holding of replay_lock
replay/replay.c: bump REPLAY_VERSION again
replay: save prior value of the host clock
replay: added replay log format description
replay: fix save/load vm for non-empty queue
replay: fixed replay_enable_events
replay: fix processing async events
cpu-exec: fix exception_index handling
hw/i386/pc: Factor out the superio code
hw/alpha/dp264: Use the TYPE_SMC37C669_SUPERIO
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# default-configs/i386-softmmu.mak
# default-configs/x86_64-softmmu.mak
there is no point to read fields here but not actually
checking them so drop it and read only header + dsdt/facs
addresses since it's needed later to fetch that tables.
With this cleanup we can get rid of AcpiFadtDescriptorRev3/
ACPI_FADT_COMMON_DEF which have no users left.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Extend generic build_fadt() to support rev5.1 FADT
and reuse it for 'virt' board, it would allow to
phase out usage of AcpiFadtDescriptorRev5_1 and
later ACPI_FADT_COMMON_DEF.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It will be extended and reused by follow up patch for ARM target.
PS:
Since it's generic function now, don't patch FIRMWARE_CTRL, DSDT
fields if they don't point to tables since platform might not
provide them and use X_ variants instead if applicable.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
move FADT data initialization out of fadt_setup() into dedicated
init_fadt_data() that will set common for pc/q35 values in
AcpiFadtData structure and acpi_get_pm_info() will complement
it with pc/q35 specific values initialization.
That will allow to get rid of fadt_setup() and generalize
build_fadt() so it could be easily extended for rev5 and
reused by ARM target.
While at it also move facs/dsdt/xdsdt offsets from build_fadt()
arg list into AcpiFadtData, as they belong to the same dataset.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
ACPI_PORT_SMI_CMD is alias for APM_CNT_IOPORT,
so make it really one instead of duplicating its value.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
it will help to add Generic Address Structure to ACPI tables
without using packed C structures and avoid endianness
issues as API doesn't need an explicit conversion.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Drop duplicate in form of Acpi20GenericAddress and reuse
AcpiGenericAddress.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Although linkspeed and duplex can be set in a linux guest via 'ethtool -s',
this requires custom ethtool commands for virtio-net by default.
Introduce a new feature flag, VIRTIO_NET_F_SPEED_DUPLEX, which allows
the hypervisor to export a linkspeed and duplex setting. The user can
subsequently overwrite it later if desired via: 'ethtool -s'.
Linkspeed and duplex settings can be set as:
'-device virtio-net,speed=10000,duplex=full'
where speed is [0...INT_MAX], and duplex is ["half"|"full"].
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: virtio-dev@lists.oasis-open.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In prepartion for using some of the high order feature bits, make sure that
virtio-net uses 64-bit values everywhere.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: virtio-dev@lists.oasis-open.org
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
At the moment we unconditionally avoid mapping MSIX data of a BAR and
emulate MSIX table in QEMU. However it is 1) not always necessary as
a platform may provide a paravirt interface for MSIX configuration;
2) can affect the speed of MMIO access by emulating them in QEMU when
frequently accessed registers share same system page with MSIX data,
this is particularly a problem for systems with the page size bigger
than 4KB.
A new capability - VFIO_REGION_INFO_CAP_MSIX_MAPPABLE - has been added
to the kernel [1] which tells the userspace that mapping of the MSIX data
is possible now. This makes use of it so from now on QEMU tries mapping
the entire BAR as a whole and emulate MSIX on top of that.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=a32295c612c57990d17fb0f41e7134394b2f35f6
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
When CPU supports memory encryption feature, the property can be used to
specify the encryption object to use when launching an encrypted guest.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Stefan Hajnoczi <stefanha@gmail.com>
Signed-off-by: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-23-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-20-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This function only initialize the ISA bus.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-19-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-17-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-15-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the PC87312 inherits this abstract model, we remove the I8042
instance in the PREP machine.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20180308223946.26784-14-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-13-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-12-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-11-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-10-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-9-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This matches the isa_register_ioport() prototype.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-7-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (hw/ppc)
Message-Id: <20180308223946.26784-6-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (hw/ppc)
Message-Id: <20180308223946.26784-4-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Move the header from hw/isa/ to hw/dma/
- Remove the old i386/pc dependency
- use a bool type for the high_page_enable argument
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-3-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Again... (after 07dc788054 and 9157eee1b1).
We now extract the ISA bus specific helpers.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180308223946.26784-2-f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The global hack for creating SCSI devices has recently been removed,
but this apparently broke SCSI devices on some boards that were not
ready for this change yet. For the pica61 machine you now get:
$ mips64-softmmu/qemu-system-mips64 -M pica61 -cdrom x.iso
qemu-system-mips64: -cdrom x.iso: machine type does not support if=scsi,bus=0,unit=2
Fix it by calling scsi_bus_legacy_handle_cmdline() after creating the
corresponding SCSI controller.
Fixes: 1454509726
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1520414644-11535-1-git-send-email-thuth@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The e1000 NIC is getting old and is not a very good default for a
PCIe machine type. Change it to e1000e, which should be supported
by a good number of guests.
In particular, drivers for 82574 were added first to Linux 2.6.27 (2008)
and Windows 2008 R2. This does mean that Windows 2008 will not work
anymore with Q35 machine types and a default "-net nic -net xxx" network
configuration; it did work before because it does have an AHCI driver.
However, Windows 2008 has been declared out of main stream support
in 2015. It will get out of extended support in 2020. Windows 2008
R2 has the same end of support dates and, since the two are basically
Vista vs. Windows 7, R2 probably is more popular.
Reviewed-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add code needed to get a functional PCI subsytem when using in
conjunction with upstream Linux guest (4.13+). Tested to work against
"e1000e" (network adapter, using MSI interrupts) as well as
"usb-ehci" (USB controller, using legacy PCI interrupts).
Based on "i.MX6 Applications Processor Reference Manual" (Document
Number: IMX6DQRM Rev. 4) as well as corresponding dirver in Linux
kernel (circa 4.13 - 4.16 found in drivers/pci/dwc/*)
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This release renames the SiFive machines to sifive_e and sifive_u
to represent the SiFive Everywhere and SiFive Unleashed platforms.
SiFive has configurable soft-core IP, so it is intended that these
machines will be extended to enable a variety of SiFive IP blocks.
The CPU definition infrastructure has been improved and there are
now vendor CPU modules including the SiFiVe E31, E51, U34 and U54
cores. The emulation accuracy for the E series has been improved
by disabling the MMU for the E series. S mode has been disabled on
cores that only support M mode and U mode. The two Spike machines
that support two privileged ISA versions have been coalesced into
one file. This series has Signed-off-by from the core contributors.
*** Known Issues ***
* Disassembler has some checkpatch warnings for the sake of code brevity
* scripts/qemu-binfmt-conf.sh has checkpatch warnings due to line length
* PMP (Physical Memory Protection) is as-of-yet unused and needs testing
*** Changelog ***
v8.2
* Rebase
v8.1
* Fix missed case of renaming spike_v1.9 to spike_v1.9.1
v8
* Added linux-user/riscv/target_elf.h during rebase
* Make resetvec configurable and clear mpp and mie on reset
* Use SiFive E31, E51, U34 and U54 cores in SiFive machines
* Define SiFive E31, E51, U34 and U54 cores
* Refactor CPU core definition in preparation for vendor cores
* Prevent S or U mode unless S or U extensions are present
* SiFive E Series cores have no MMU
* SiFive E Series cores have U mode
* Make privileged ISA v1.10 implicit in CPU types
* Remove DRAM_BASE and EXT_IO_BASE as they vary by machine
* Correctly handle mtvec and stvec alignment with respect to RVC
* Print more machine mode state in riscv_cpu_dump_state
* Make riscv_isa_string use compact extension order method
* Fix bug introduced in v6 RISCV_CPU_TYPE_NAME macro change
* Parameterize spike v1.9.1 config string
* Coalesce spike_v1.9.1 and spike_v1.10 machines
* Rename sifive_e300 to sifive_e, and sifive_u500 to sifive_u
v7
* Make spike_v1.10 the default machine
* Rename spike_v1.9 to spike_v1.9.1 to match privileged spec version
* Remove empty target/riscv/trace-events file
* Monitor ROM 32-bit reset code needs to be target endian
* Add TARGET_TIOCGPTPEER to linux-user/riscv/termbits.h
* Add -initrd support to the virt board
* Fix naming in spike machine interface header
* Update copyright notice on RISC-V Spike machines
* Update copyright notice on RISC-V HTIF Console device
* Change CPU Core and translator to GPLv2+
* Change RISC-V Disassembler to GPLv2+
* Change SiFive Test Finisher to GPLv2+
* Change SiFive CLINT to GPLv2+
* Change SiFive PRCI to GPLv2+
* Change SiFive PLIC to GPLv2+
* Change RISC-V spike machines to GPLv2+
* Change RISC-V virt machine to GPLv2+
* Change SiFive E300 machine to GPLv2+
* Change SiFive U500 machine to GPLv2+
* Change RISC-V Hart Array to GPLv2+
* Change RISC-V HTIF device to GPLv2+
* Change SiFiveUART device to GPLv2+
v6
* Drop IEEE 754-201x minimumNumber/maximumNumber for fmin/fmax
* Remove some unnecessary commented debug statements
* Change RISCV_CPU_TYPE_NAME to use riscv-cpu suffix
* Define all CPU variants for linux-user
* qemu_log calls require trailing \n
* Replace PLIC printfs with qemu_log
* Tear out unused HTIF code and eliminate shouting debug messages
* Fix illegal instruction when sfence.vma is passed (rs2) arguments
* Make updates to PTE accessed and dirty bits atomic
* Only require atomic PTE updates on MTTCG enabled guests
* Page fault if accessed or dirty bits can't be updated
* Fix get_physical_address PTE reads and writes on riscv32
* Remove erroneous comments from the PLIC
* Default enable MTTCG
* Make WFI less conservative
* Unify local interrupt handling
* Expunge HTIF interrupts
* Always access mstatus.mip under a lock
* Don't implement rdtime/rdtimeh in system mode (bbl emulates them)
* Implement insreth/cycleh for rv32 and always enable user-mode counters
* Add GDB stub support for reading and writing CSRs
* Rename ENABLE_CHARDEV #ifdef from HTIF code
* Replace bad HTIF ELF code with load_elf symbol callback
* Convert chained if else fault handlers to switch statements
* Use RISCV exception codes for linux-user page faults
v5
* Implement NaN-boxing for flw, set high order bits to 1
* Use float_muladd_negate_* flags to floatXX_muladd
* Use IEEE 754-201x minimumNumber/maximumNumber for fmin/fmax
* Fix TARGET_NR_syscalls
* Update linux-user/riscv/syscall_nr.h
* Fix FENCE.I, needs to terminate translation block
* Adjust unusual convention for interruptno >= 0
v4
* Add @riscv: since 2.12 to CpuInfoArch
* Remove misleading little-endian comment from load_kernel
* Rename cpu-model property to cpu-type
* Drop some unnecessary inline function attributes
* Don't allow GDB to set value of x0 register
* Remove unnecessary empty property lists
* Add Test Finisher device to implement poweroff in virt machine
* Implement priv ISA v1.10 trap and sret/mret xPIE/xIE behavior
* Store fflags data in fp_status
* Purge runtime users of helper_raise_exception
* Fix validate_csr
* Tidy gen_jalr
* Tidy immediate shifts
* Add gen_exception_inst_addr_mis
* Add gen_exception_debug
* Add gen_exception_illegal
* Tidy helper_fclass_*
* Split rounding mode setting to a new function
* Enforce MSTATUS_FS via TB flags
* Implement acquire/release barrier semantics
* Use atomic operations as required
* Fix FENCE and FENCE_I
* Remove commented code from spike machines
* PAGE_WRITE permissions can be set on loads if page is already dirty
* The result of format conversion on an NaN must be a quiet NaN
* Add missing process_queued_cpu_work to riscv linux-user
* Remove float(32|64)_classify from cpu.h
* Removed nonsensical unions aliasing the same type
* Use uintN_t instead of uintN_fast_t in fpu_helper.c
* Use macros for FPU exception values in softfloat_flags_to_riscv
* Move code to set round mode into set_fp_round_mode function
* Convert set_fp_exceptions from a macro to an inline function
* Convert round mode helper into an inline function
* Make fpu_helper ieee_rm array static const
* Include cpu_mmu_index in cpu_get_tb_cpu_state flags
* Eliminate MPRV influence on mmu_index
* Remove unrecoverable do_unassigned_access function
* Only update PTE accessed and dirty bits if necessary
* Remove unnecessary tlb_flush in set_mode as mode is in mmu_idx
* Remove buggy support for misa writes. misa writes are optional
and are not implemented in any known hardware
* Always set PTE read or execute permissions during page walk
* Reorder helper function declarations to match order in helper.c
* Remove redundant variable declaration in get_physical_address
* Remove duplicated code from get_physical_address
* Use mmu_idx instead of mem_idx in riscv_cpu_get_phys_page_debug
v3
* Fix indentation in PMP and HTIF debug macros
* Fix disassembler checkpatch open brace '{' on next line errors
* Fix trailing statements on next line in decode_inst_decompress
* NOTE: the other checkpatch issues have been reviewed previously
v2
* Remove redundant NULL terminators from disassembler register arrays
* Change disassembler register name arrays to const
* Refine disassembler internal function names
* Update dates in disassembler copyright message
* Remove #ifdef CONFIG_USER_ONLY version of cpu_has_work
* Use ULL suffix on 64-bit constants
* Move riscv_cpu_mmu_index from cpu.h to helper.c
* Move riscv_cpu_hw_interrupts_pending from cpu.h to helper.c
* Remove redundant TARGET_HAS_ICE from cpu.h
* Use qemu_irq instead of void* for irq definition in cpu.h
* Remove duplicate typedef from struct CPURISCVState
* Remove redundant g_strdup from cpu_register
* Remove redundant tlb_flush from riscv_cpu_reset
* Remove redundant mode calculation from get_physical_address
* Remove redundant debug mode printf and dcsr comment
* Remove redundant clearing of MSB for bare physical addresses
* Use g_assert_not_reached for invalid mode in get_physical_address
* Use g_assert_not_reached for unreachable checks in get_physical_address
* Use g_assert_not_reached for unreachable type in raise_mmu_exception
* Return exception instead of aborting for misaligned fetches
* Move exception defines from cpu.h to cpu_bits.h
* Remove redundant breakpoint control definitions from cpu_bits.h
* Implement riscv_cpu_unassigned_access exception handling
* Log and raise exceptions for unimplemented CSRs
* Match Spike HTIF exit behavior - don’t print TEST-PASSED
* Make frm,fflags,fcsr writes trap when mstatus.FS is clear
* Use g_assert_not_reached for unreachable invalid mode
* Make hret,uret,dret generate illegal instructions
* Move riscv_cpu_dump_state and int/fpr regnames to cpu.c
* Lift interrupt flag and mask into constants in cpu_bits.h
* Change trap debugging to use qemu_log_mask LOG_TRACE
* Change CSR debugging to use qemu_log_mask LOG_TRACE
* Change PMP debugging to use qemu_log_mask LOG_TRACE
* Remove commented code from pmp.c
* Change CpuInfoRISCV qapi schema docs to Since 2.12
* Change RV feature macro to use target_ulong cast
* Remove riscv_feature and instead use misa extension flags
* Make riscv_flush_icache_syscall a no-op
* Undo checkpatch whitespace fixes in unrelated linux-user code
* Remove redudant constants and tidy up cpu_bits.h
* Make helper_fence_i a no-op
* Move include "exec/cpu-all" to end of cpu.h
* Rename set_privilege to riscv_set_mode
* Move redundant forward declaration for cpu_riscv_translate_address
* Remove TCGV_UNUSED from riscv_translate_init
* Add comment to pmp.c stating the code is untested and currently unused
* Use ctz to simplify decoding of PMP NAPOT address ranges
* Change pmp_is_in_range to use than equal for end addresses
* Fix off by one error in pmp_update_rule
* Rearrange PMP_DEBUG so that formatting is compile-time checked
* Rearrange trap debugging so that formatting is compile-time checked
* Rearrange PLIC debugging so that formatting is compile-time checked
* Use qemu_log/qemu_log_mask for HTIF logging and debugging
* Move exception and interrupt names into cpu.c
* Add Palmer Dabbelt as a RISC-V Maintainer
* Rebase against current qemu master branch
v1
* initial version based on forward port from riscv-qemu repository
*** Background ***
"RISC-V is an open, free ISA enabling a new era of processor innovation
through open standard collaboration. Born in academia and research,
RISC-V ISA delivers a new level of free, extensible software and
hardware freedom on architecture, paving the way for the next 50 years
of computing design and innovation."
The QEMU RISC-V port has been developed and maintained out-of-tree for
several years by Sagar Karandikar and Bastian Koppelmann. The RISC-V
Privileged specification has evolved substantially over this period but
has recently been solidifying. The RISC-V Base ISA has been frozon for
some time and the Privileged ISA, GCC toolchain and Linux ABI are now
quite stable. I have recently joined Sagar and Bastian as a RISC-V QEMU
Maintainer and hope to support upstreaming the port.
There are multiple vendors taping out, preparing to ship, or shipping
silicon that implements the RISC-V Privileged ISA Version 1.10. There
are also several RISC-V Soft-IP cores implementing Privileged ISA
Version 1.10 that run on FPGA such as SiFive's Freedom U500 Platform
and the U54‑MC RISC-V Core IP, among many more implementations from a
variety of vendors. See https://riscv.org/ for more details.
RISC-V support was upstreamed in binutils 2.28 and GCC 7.1 in the first
half of 2016. RISC-V support is now available in LLVM top-of-tree and
the RISC-V Linux port was accepted into Linux 4.15-rc1 late last year
and is available in the Linux 4.15 release. GLIBC 2.27 added support
for the RISC-V ISA running on Linux (requires at least binutils-2.30,
gcc-7.3.0, and linux-4.15). We believe it is timely to submit the
RISC-V QEMU port for upstream review with the goal of incorporating
RISC-V support into the upcoming QEMU 2.12 release.
The RISC-V QEMU port is still under active development, mostly with
respect to device emulation, the addition of Hypervisor support as
specified in the RISC-V Draft Privileged ISA Version 1.11, and Vector
support once the first draft is finalized later this year. We believe
now is the appropriate time for RISC-V QEMU development to be carried
out in the main QEMU repository as the code will benefit from more
rigorous review. The RISC-V QEMU port currently supports all the ISA
extensions that have been finalized and frozen in the Base ISA.
Blog post about recent additions to RISC-V QEMU: https://goo.gl/fJ4zgk
The RISC-V QEMU wiki: https://github.com/riscv/riscv-qemu/wiki
Instructions for building a busybox+dropbear root image, BBL (Berkeley
Boot Loader) and linux kernel image for use with the RISC-V QEMU
'virt' machine: https://github.com/michaeljclark/busybear-linux
*** Overview ***
The RISC-V QEMU port implements the following specifications:
* RISC-V Instruction Set Manual Volume I: User-Level ISA Version 2.2
* RISC-V Instruction Set Manual Volume II: Privileged ISA Version 1.9.1
* RISC-V Instruction Set Manual Volume II: Privileged ISA Version 1.10
The RISC-V QEMU port supports the following instruction set extensions:
* RV32GC with Supervisor-mode and User-mode (RV32IMAFDCSU)
* RV64GC with Supervisor-mode and User-mode (RV64IMAFDCSU)
The RISC-V QEMU port adds the following targets to QEMU:
* riscv32-softmmu
* riscv64-softmmu
* riscv32-linux-user
* riscv64-linux-user
The RISC-V QEMU port supports the following hardware:
* HTIF Console (Host Target Interface)
* SiFive CLINT (Core Local Interruptor) for Timer interrupts and IPIs
* SiFive PLIC (Platform Level Interrupt Controller)
* SiFive Test (Test Finisher) for exiting simulation
* SiFive UART, PRCI, AON, PWM, QSPI support is partially implemented
* VirtIO MMIO (GPEX PCI support will be added in a future patch)
* Generic 16550A UART emulation using 'hw/char/serial.c'
* MTTCG and SMP support (PLIC and CLINT) on the 'virt' machine
The RISC-V QEMU full system emulator supports 5 machines:
* 'spike_v1.9.1', CLINT, PLIC, HTIF console, config-string, Priv v1.9.1
* 'spike_v1.10', CLINT, PLIC, HTIF console, device-tree, Priv v1.10
* 'sifive_e', CLINT, PLIC, SiFive UART, HiFive1 compat, Priv v1.10
* 'sifive_u', CLINT, PLIC, SiFive UART, device-tree, Priv v1.10
* 'virt', CLINT, PLIC, 16550A UART, VirtIO, device-tree, Priv v1.10
This is a list of RISC-V QEMU Port Contributors:
* Alex Suykov
* Andreas Schwab
* Antony Pavlov
* Bastian Koppelmann
* Bruce Hoult
* Chih-Min Chao
* Daire McNamara
* Darius Rad
* David Abdurachmanov
* Hesham Almatary
* Ivan Griffin
* Jim Wilson
* Kito Cheng
* Michael Clark
* Palmer Dabbelt
* Richard Henderson
* Sagar Karandikar
* Shea Levy
* Stefan O'Rear
Notes:
* contributor email addresses available off-list on request.
* checkpatch has been run on all 23 patches.
* checkpatch exceptions are noted in patches that have errors.
* passes "make check" on full build for all targets
* tested riscv-linux-4.6.2 on 'spike_v1.9.1' machine
* tested riscv-linux-4.15 on 'spike_v1.10' and 'virt' machines
* tested SiFive HiFive1 binaries in 'sifive_e' machine
* tested RV64 on 32-bit i386
This patch series includes the following patches:
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQR8mZMOsXzYugc9Xvpr8dezV+8+TwUCWqGRpAAKCRBr8dezV+8+
T2mMAJ9ptK/7Bs3lE+Mki/ymlTPqhXtyxACfZkyfQf1mfhcXnB+oTG1RvEtblY8=
=TJc8
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/riscv/tags/riscv-qemu-upstream-v8.2' into staging
QEMU RISC-V Emulation Support (RV64GC, RV32GC)
This release renames the SiFive machines to sifive_e and sifive_u
to represent the SiFive Everywhere and SiFive Unleashed platforms.
SiFive has configurable soft-core IP, so it is intended that these
machines will be extended to enable a variety of SiFive IP blocks.
The CPU definition infrastructure has been improved and there are
now vendor CPU modules including the SiFiVe E31, E51, U34 and U54
cores. The emulation accuracy for the E series has been improved
by disabling the MMU for the E series. S mode has been disabled on
cores that only support M mode and U mode. The two Spike machines
that support two privileged ISA versions have been coalesced into
one file. This series has Signed-off-by from the core contributors.
*** Known Issues ***
* Disassembler has some checkpatch warnings for the sake of code brevity
* scripts/qemu-binfmt-conf.sh has checkpatch warnings due to line length
* PMP (Physical Memory Protection) is as-of-yet unused and needs testing
*** Changelog ***
v8.2
* Rebase
v8.1
* Fix missed case of renaming spike_v1.9 to spike_v1.9.1
v8
* Added linux-user/riscv/target_elf.h during rebase
* Make resetvec configurable and clear mpp and mie on reset
* Use SiFive E31, E51, U34 and U54 cores in SiFive machines
* Define SiFive E31, E51, U34 and U54 cores
* Refactor CPU core definition in preparation for vendor cores
* Prevent S or U mode unless S or U extensions are present
* SiFive E Series cores have no MMU
* SiFive E Series cores have U mode
* Make privileged ISA v1.10 implicit in CPU types
* Remove DRAM_BASE and EXT_IO_BASE as they vary by machine
* Correctly handle mtvec and stvec alignment with respect to RVC
* Print more machine mode state in riscv_cpu_dump_state
* Make riscv_isa_string use compact extension order method
* Fix bug introduced in v6 RISCV_CPU_TYPE_NAME macro change
* Parameterize spike v1.9.1 config string
* Coalesce spike_v1.9.1 and spike_v1.10 machines
* Rename sifive_e300 to sifive_e, and sifive_u500 to sifive_u
v7
* Make spike_v1.10 the default machine
* Rename spike_v1.9 to spike_v1.9.1 to match privileged spec version
* Remove empty target/riscv/trace-events file
* Monitor ROM 32-bit reset code needs to be target endian
* Add TARGET_TIOCGPTPEER to linux-user/riscv/termbits.h
* Add -initrd support to the virt board
* Fix naming in spike machine interface header
* Update copyright notice on RISC-V Spike machines
* Update copyright notice on RISC-V HTIF Console device
* Change CPU Core and translator to GPLv2+
* Change RISC-V Disassembler to GPLv2+
* Change SiFive Test Finisher to GPLv2+
* Change SiFive CLINT to GPLv2+
* Change SiFive PRCI to GPLv2+
* Change SiFive PLIC to GPLv2+
* Change RISC-V spike machines to GPLv2+
* Change RISC-V virt machine to GPLv2+
* Change SiFive E300 machine to GPLv2+
* Change SiFive U500 machine to GPLv2+
* Change RISC-V Hart Array to GPLv2+
* Change RISC-V HTIF device to GPLv2+
* Change SiFiveUART device to GPLv2+
v6
* Drop IEEE 754-201x minimumNumber/maximumNumber for fmin/fmax
* Remove some unnecessary commented debug statements
* Change RISCV_CPU_TYPE_NAME to use riscv-cpu suffix
* Define all CPU variants for linux-user
* qemu_log calls require trailing \n
* Replace PLIC printfs with qemu_log
* Tear out unused HTIF code and eliminate shouting debug messages
* Fix illegal instruction when sfence.vma is passed (rs2) arguments
* Make updates to PTE accessed and dirty bits atomic
* Only require atomic PTE updates on MTTCG enabled guests
* Page fault if accessed or dirty bits can't be updated
* Fix get_physical_address PTE reads and writes on riscv32
* Remove erroneous comments from the PLIC
* Default enable MTTCG
* Make WFI less conservative
* Unify local interrupt handling
* Expunge HTIF interrupts
* Always access mstatus.mip under a lock
* Don't implement rdtime/rdtimeh in system mode (bbl emulates them)
* Implement insreth/cycleh for rv32 and always enable user-mode counters
* Add GDB stub support for reading and writing CSRs
* Rename ENABLE_CHARDEV #ifdef from HTIF code
* Replace bad HTIF ELF code with load_elf symbol callback
* Convert chained if else fault handlers to switch statements
* Use RISCV exception codes for linux-user page faults
v5
* Implement NaN-boxing for flw, set high order bits to 1
* Use float_muladd_negate_* flags to floatXX_muladd
* Use IEEE 754-201x minimumNumber/maximumNumber for fmin/fmax
* Fix TARGET_NR_syscalls
* Update linux-user/riscv/syscall_nr.h
* Fix FENCE.I, needs to terminate translation block
* Adjust unusual convention for interruptno >= 0
v4
* Add @riscv: since 2.12 to CpuInfoArch
* Remove misleading little-endian comment from load_kernel
* Rename cpu-model property to cpu-type
* Drop some unnecessary inline function attributes
* Don't allow GDB to set value of x0 register
* Remove unnecessary empty property lists
* Add Test Finisher device to implement poweroff in virt machine
* Implement priv ISA v1.10 trap and sret/mret xPIE/xIE behavior
* Store fflags data in fp_status
* Purge runtime users of helper_raise_exception
* Fix validate_csr
* Tidy gen_jalr
* Tidy immediate shifts
* Add gen_exception_inst_addr_mis
* Add gen_exception_debug
* Add gen_exception_illegal
* Tidy helper_fclass_*
* Split rounding mode setting to a new function
* Enforce MSTATUS_FS via TB flags
* Implement acquire/release barrier semantics
* Use atomic operations as required
* Fix FENCE and FENCE_I
* Remove commented code from spike machines
* PAGE_WRITE permissions can be set on loads if page is already dirty
* The result of format conversion on an NaN must be a quiet NaN
* Add missing process_queued_cpu_work to riscv linux-user
* Remove float(32|64)_classify from cpu.h
* Removed nonsensical unions aliasing the same type
* Use uintN_t instead of uintN_fast_t in fpu_helper.c
* Use macros for FPU exception values in softfloat_flags_to_riscv
* Move code to set round mode into set_fp_round_mode function
* Convert set_fp_exceptions from a macro to an inline function
* Convert round mode helper into an inline function
* Make fpu_helper ieee_rm array static const
* Include cpu_mmu_index in cpu_get_tb_cpu_state flags
* Eliminate MPRV influence on mmu_index
* Remove unrecoverable do_unassigned_access function
* Only update PTE accessed and dirty bits if necessary
* Remove unnecessary tlb_flush in set_mode as mode is in mmu_idx
* Remove buggy support for misa writes. misa writes are optional
and are not implemented in any known hardware
* Always set PTE read or execute permissions during page walk
* Reorder helper function declarations to match order in helper.c
* Remove redundant variable declaration in get_physical_address
* Remove duplicated code from get_physical_address
* Use mmu_idx instead of mem_idx in riscv_cpu_get_phys_page_debug
v3
* Fix indentation in PMP and HTIF debug macros
* Fix disassembler checkpatch open brace '{' on next line errors
* Fix trailing statements on next line in decode_inst_decompress
* NOTE: the other checkpatch issues have been reviewed previously
v2
* Remove redundant NULL terminators from disassembler register arrays
* Change disassembler register name arrays to const
* Refine disassembler internal function names
* Update dates in disassembler copyright message
* Remove #ifdef CONFIG_USER_ONLY version of cpu_has_work
* Use ULL suffix on 64-bit constants
* Move riscv_cpu_mmu_index from cpu.h to helper.c
* Move riscv_cpu_hw_interrupts_pending from cpu.h to helper.c
* Remove redundant TARGET_HAS_ICE from cpu.h
* Use qemu_irq instead of void* for irq definition in cpu.h
* Remove duplicate typedef from struct CPURISCVState
* Remove redundant g_strdup from cpu_register
* Remove redundant tlb_flush from riscv_cpu_reset
* Remove redundant mode calculation from get_physical_address
* Remove redundant debug mode printf and dcsr comment
* Remove redundant clearing of MSB for bare physical addresses
* Use g_assert_not_reached for invalid mode in get_physical_address
* Use g_assert_not_reached for unreachable checks in get_physical_address
* Use g_assert_not_reached for unreachable type in raise_mmu_exception
* Return exception instead of aborting for misaligned fetches
* Move exception defines from cpu.h to cpu_bits.h
* Remove redundant breakpoint control definitions from cpu_bits.h
* Implement riscv_cpu_unassigned_access exception handling
* Log and raise exceptions for unimplemented CSRs
* Match Spike HTIF exit behavior - don’t print TEST-PASSED
* Make frm,fflags,fcsr writes trap when mstatus.FS is clear
* Use g_assert_not_reached for unreachable invalid mode
* Make hret,uret,dret generate illegal instructions
* Move riscv_cpu_dump_state and int/fpr regnames to cpu.c
* Lift interrupt flag and mask into constants in cpu_bits.h
* Change trap debugging to use qemu_log_mask LOG_TRACE
* Change CSR debugging to use qemu_log_mask LOG_TRACE
* Change PMP debugging to use qemu_log_mask LOG_TRACE
* Remove commented code from pmp.c
* Change CpuInfoRISCV qapi schema docs to Since 2.12
* Change RV feature macro to use target_ulong cast
* Remove riscv_feature and instead use misa extension flags
* Make riscv_flush_icache_syscall a no-op
* Undo checkpatch whitespace fixes in unrelated linux-user code
* Remove redudant constants and tidy up cpu_bits.h
* Make helper_fence_i a no-op
* Move include "exec/cpu-all" to end of cpu.h
* Rename set_privilege to riscv_set_mode
* Move redundant forward declaration for cpu_riscv_translate_address
* Remove TCGV_UNUSED from riscv_translate_init
* Add comment to pmp.c stating the code is untested and currently unused
* Use ctz to simplify decoding of PMP NAPOT address ranges
* Change pmp_is_in_range to use than equal for end addresses
* Fix off by one error in pmp_update_rule
* Rearrange PMP_DEBUG so that formatting is compile-time checked
* Rearrange trap debugging so that formatting is compile-time checked
* Rearrange PLIC debugging so that formatting is compile-time checked
* Use qemu_log/qemu_log_mask for HTIF logging and debugging
* Move exception and interrupt names into cpu.c
* Add Palmer Dabbelt as a RISC-V Maintainer
* Rebase against current qemu master branch
v1
* initial version based on forward port from riscv-qemu repository
*** Background ***
"RISC-V is an open, free ISA enabling a new era of processor innovation
through open standard collaboration. Born in academia and research,
RISC-V ISA delivers a new level of free, extensible software and
hardware freedom on architecture, paving the way for the next 50 years
of computing design and innovation."
The QEMU RISC-V port has been developed and maintained out-of-tree for
several years by Sagar Karandikar and Bastian Koppelmann. The RISC-V
Privileged specification has evolved substantially over this period but
has recently been solidifying. The RISC-V Base ISA has been frozon for
some time and the Privileged ISA, GCC toolchain and Linux ABI are now
quite stable. I have recently joined Sagar and Bastian as a RISC-V QEMU
Maintainer and hope to support upstreaming the port.
There are multiple vendors taping out, preparing to ship, or shipping
silicon that implements the RISC-V Privileged ISA Version 1.10. There
are also several RISC-V Soft-IP cores implementing Privileged ISA
Version 1.10 that run on FPGA such as SiFive's Freedom U500 Platform
and the U54‑MC RISC-V Core IP, among many more implementations from a
variety of vendors. See https://riscv.org/ for more details.
RISC-V support was upstreamed in binutils 2.28 and GCC 7.1 in the first
half of 2016. RISC-V support is now available in LLVM top-of-tree and
the RISC-V Linux port was accepted into Linux 4.15-rc1 late last year
and is available in the Linux 4.15 release. GLIBC 2.27 added support
for the RISC-V ISA running on Linux (requires at least binutils-2.30,
gcc-7.3.0, and linux-4.15). We believe it is timely to submit the
RISC-V QEMU port for upstream review with the goal of incorporating
RISC-V support into the upcoming QEMU 2.12 release.
The RISC-V QEMU port is still under active development, mostly with
respect to device emulation, the addition of Hypervisor support as
specified in the RISC-V Draft Privileged ISA Version 1.11, and Vector
support once the first draft is finalized later this year. We believe
now is the appropriate time for RISC-V QEMU development to be carried
out in the main QEMU repository as the code will benefit from more
rigorous review. The RISC-V QEMU port currently supports all the ISA
extensions that have been finalized and frozen in the Base ISA.
Blog post about recent additions to RISC-V QEMU: https://goo.gl/fJ4zgk
The RISC-V QEMU wiki: https://github.com/riscv/riscv-qemu/wiki
Instructions for building a busybox+dropbear root image, BBL (Berkeley
Boot Loader) and linux kernel image for use with the RISC-V QEMU
'virt' machine: https://github.com/michaeljclark/busybear-linux
*** Overview ***
The RISC-V QEMU port implements the following specifications:
* RISC-V Instruction Set Manual Volume I: User-Level ISA Version 2.2
* RISC-V Instruction Set Manual Volume II: Privileged ISA Version 1.9.1
* RISC-V Instruction Set Manual Volume II: Privileged ISA Version 1.10
The RISC-V QEMU port supports the following instruction set extensions:
* RV32GC with Supervisor-mode and User-mode (RV32IMAFDCSU)
* RV64GC with Supervisor-mode and User-mode (RV64IMAFDCSU)
The RISC-V QEMU port adds the following targets to QEMU:
* riscv32-softmmu
* riscv64-softmmu
* riscv32-linux-user
* riscv64-linux-user
The RISC-V QEMU port supports the following hardware:
* HTIF Console (Host Target Interface)
* SiFive CLINT (Core Local Interruptor) for Timer interrupts and IPIs
* SiFive PLIC (Platform Level Interrupt Controller)
* SiFive Test (Test Finisher) for exiting simulation
* SiFive UART, PRCI, AON, PWM, QSPI support is partially implemented
* VirtIO MMIO (GPEX PCI support will be added in a future patch)
* Generic 16550A UART emulation using 'hw/char/serial.c'
* MTTCG and SMP support (PLIC and CLINT) on the 'virt' machine
The RISC-V QEMU full system emulator supports 5 machines:
* 'spike_v1.9.1', CLINT, PLIC, HTIF console, config-string, Priv v1.9.1
* 'spike_v1.10', CLINT, PLIC, HTIF console, device-tree, Priv v1.10
* 'sifive_e', CLINT, PLIC, SiFive UART, HiFive1 compat, Priv v1.10
* 'sifive_u', CLINT, PLIC, SiFive UART, device-tree, Priv v1.10
* 'virt', CLINT, PLIC, 16550A UART, VirtIO, device-tree, Priv v1.10
This is a list of RISC-V QEMU Port Contributors:
* Alex Suykov
* Andreas Schwab
* Antony Pavlov
* Bastian Koppelmann
* Bruce Hoult
* Chih-Min Chao
* Daire McNamara
* Darius Rad
* David Abdurachmanov
* Hesham Almatary
* Ivan Griffin
* Jim Wilson
* Kito Cheng
* Michael Clark
* Palmer Dabbelt
* Richard Henderson
* Sagar Karandikar
* Shea Levy
* Stefan O'Rear
Notes:
* contributor email addresses available off-list on request.
* checkpatch has been run on all 23 patches.
* checkpatch exceptions are noted in patches that have errors.
* passes "make check" on full build for all targets
* tested riscv-linux-4.6.2 on 'spike_v1.9.1' machine
* tested riscv-linux-4.15 on 'spike_v1.10' and 'virt' machines
* tested SiFive HiFive1 binaries in 'sifive_e' machine
* tested RV64 on 32-bit i386
This patch series includes the following patches:
# gpg: Signature made Thu 08 Mar 2018 19:40:20 GMT
# gpg: using DSA key 6BF1D7B357EF3E4F
# gpg: Good signature from "Michael Clark <michaeljclark@mac.com>"
# gpg: aka "Michael Clark <mjc@sifive.com>"
# gpg: aka "Michael Clark <michael@metaparadigm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 7C99 930E B17C D8BA 073D 5EFA 6BF1 D7B3 57EF 3E4F
* remotes/riscv/tags/riscv-qemu-upstream-v8.2: (23 commits)
RISC-V Build Infrastructure
SiFive Freedom U Series RISC-V Machine
SiFive Freedom E Series RISC-V Machine
SiFive RISC-V PRCI Block
SiFive RISC-V UART Device
RISC-V VirtIO Machine
SiFive RISC-V Test Finisher
RISC-V Spike Machines
SiFive RISC-V PLIC Block
SiFive RISC-V CLINT Block
RISC-V HART Array
RISC-V HTIF Console
Add symbol table callback interface to load_elf
RISC-V Linux User Emulation
RISC-V Physical Memory Protection
RISC-V TCG Code Generation
RISC-V GDB Stub
RISC-V FPU Support
RISC-V CPU Helpers
RISC-V Disassembler
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce an sccb_mask_t to be used for SCLP event masks instead of just
unsigned int or uint32_t. This will allow later to extend the mask with
more ease.
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Message-Id: <1519407778-23095-3-git-send-email-imbrenda@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
The other event handlers (quiesce and cpu) do not define these
handlers, and this one does nothing, so it can be removed.
Signed-off-by: Nia Alarie <nia.alarie@gmail.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20180306100721.19419-1-nia.alarie@gmail.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
This provides a RISC-V Board compatible with the the SiFive Freedom U SDK.
The following machine is implemented:
- 'sifive_u'; CLINT, PLIC, UART, device-tree
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
This provides a RISC-V Board compatible with the the SiFive Freedom E SDK.
The following machine is implemented:
- 'sifive_e'; CLINT, PLIC, UART, AON, GPIO, QSPI, PWM
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Simple model of the PRCI (Power, Reset, Clock, Interrupt) to emulate
register reads made by the SDK BSP.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
QEMU model of the UART on the SiFive E300 and U500 series SOCs.
BBL supports the SiFive UART for early console access via the SBI
(Supervisor Binary Interface) and the linux kernel SBI console.
The SiFive UART implements the pre qom legacy interface consistent
with the 16550a UART in 'hw/char/serial.c'.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
RISC-V machine with device-tree, 16550a UART and VirtIO MMIO.
The following machine is implemented:
- 'virt'; CLINT, PLIC, 16550A UART, VirtIO MMIO, device-tree
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Test finisher memory mapped device used to exit simulation.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
RISC-V machines compatble with Spike aka riscv-isa-sim, the RISC-V
Instruction Set Simulator. The following machines are implemented:
- 'spike_v1.9.1'; HTIF console, config-string, Privileged ISA Version 1.9.1
- 'spike_v1.10'; HTIF console, device-tree, Privileged ISA Version 1.10
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Michael Clark <mjc@sifive.com>
The PLIC (Platform Level Interrupt Controller) device provides a
parameterizable interrupt controller based on SiFive's PLIC specification.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
The CLINT (Core Local Interruptor) device provides real-time clock, timer
and interprocessor interrupts based on SiFive's CLINT specification.
Acked-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
Holds the state of a heterogenous array of RISC-V hardware threads.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Michael Clark <mjc@sifive.com>
HTIF (Host Target Interface) provides console emulation for QEMU. HTIF
allows identical copies of BBL (Berkeley Boot Loader) and linux to run
on both Spike and QEMU. BBL provides HTIF console access via the
SBI (Supervisor Binary Interface) and the linux kernel SBI console.
The HTIT chardev implements the pre qom legacy interface consistent
with the 16550a UART in 'hw/char/serial.c'.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Sagar Karandikar <sagark@eecs.berkeley.edu>
Signed-off-by: Stefan O'Rear <sorear2@gmail.com>
Signed-off-by: Michael Clark <mjc@sifive.com>
The RISC-V HTIF (Host Target Interface) console device requires access
to the symbol table to locate the 'tohost' and 'fromhost' symbols.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Michael Clark <mjc@sifive.com>
Automatic creation of SCSI controllers for "-drive if=scsi" for x86
machines was quite a bad idea (see description of commit f778a82f0c
for details). This is marked as deprecated since QEMU v2.9.0, and as
far as I know, nobody complained that this is still urgently required
anymore. Time to remove this now.
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1519123357-13225-1-git-send-email-thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert cap-ibs (indirect branch speculation) to a custom spapr-cap
type.
All tristate caps have now been converted to custom spapr-caps, so
remove the remaining support for them.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
[dwg: Don't explicitly list "?"/help option, trust convention]
[dwg: Fold tristate removal into here, to not break bisect]
[dwg: Fix minor style problems]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also switch macio_newworld_realize() over to use it rather than using the pic_mem
memory region directly.
Now that both Old World and New World macio devices no longer make use of the
pic_mem memory region directly, we can remove it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is to faciliate access to OpenPICState when wiring up the PIC to the macio
controller.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This is needed before the next patch because the target-dependent kvm stub
uses the existing kvm_openpic_connect_vcpu() declaration, making it impossible
to move the device-specific declarations into the same file without breaking
ppc-linux-user compilation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also switch macio_oldworld_realize() over to use it rather than using the pic_mem
memory region directly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The previous commit improved compile time by including less of the
generated QAPI headers. This is impossible for stuff defined directly
in qapi-schema.json, because that ends up in headers that that pull in
everything.
Move everything but include directives from qapi-schema.json to new
sub-module qapi/misc.json, then include just the "misc" shard where
possible.
It's possible everywhere, except:
* monitor.c needs qmp-command.h to get qmp_init_marshal()
* monitor.c, ui/vnc.c and the generated qapi-event-FOO.c need
qapi-event.h to get enum QAPIEvent
Perhaps we'll get rid of those some other day.
Adding a type to qapi/migration.json now recompiles some 120 instead
of 2300 out of 5100 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-25-armbru@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
In my "build everything" tree, a change to the types in
qapi-schema.json triggers a recompile of about 4800 out of 5100
objects.
The previous commit split up qmp-commands.h, qmp-event.h, qmp-visit.h,
qapi-types.h. Each of these headers still includes all its shards.
Reduce compile time by including just the shards we actually need.
To illustrate the benefits: adding a type to qapi/migration.json now
recompiles some 2300 instead of 4800 objects. The next commit will
improve it further.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20180211093607.27351-24-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[eblake: rebase to master]
Signed-off-by: Eric Blake <eblake@redhat.com>
Add remaining easy registers to iotkit-secctl:
* NSCCFG just routes its two bits out to external GPIO lines
* BRGINSTAT/BRGINTCLR/BRGINTEN can be dummies, because QEMU's
bus fabric can never report errors
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180220180325.29818-18-peter.maydell@linaro.org
The IoTKit Security Controller includes various registers
that expose to software the controls for the Peripheral
Protection Controllers in the system. Implement these.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-17-peter.maydell@linaro.org
The Arm IoT Kit includes a "security controller" which is largely a
collection of registers for controlling the PPCs and other bits of
glue in the system. This commit provides the initial skeleton of the
device, implementing just the ID registers, and a couple of read-only
read-as-zero registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-16-peter.maydell@linaro.org
Add a model of the TrustZone peripheral protection controller (PPC),
which is used to gate transactions to non-TZ-aware peripherals so
that secure software can configure them to not be accessible to
non-secure software.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-15-peter.maydell@linaro.org
The MPS2 AN505 FPGA image includes a "FPGA control block"
which is a small set of registers handling LEDs, buttons
and some counters.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-14-peter.maydell@linaro.org
In some board or SoC models it is necessary to split a qemu_irq line
so that one input can feed multiple outputs. We currently have
qemu_irq_split() for this, but that has several deficiencies:
* it can only handle splitting a line into two
* it unavoidably leaks memory, so it can't be used
in a device that can be deleted
Implement a qdev device that encapsulates splitting of IRQs, with a
configurable number of outputs. (This is in some ways the inverse of
the TYPE_OR_IRQ device.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-13-peter.maydell@linaro.org
The function qdev_init_gpio_in_named() passes the DeviceState pointer
as the opaque data pointor for the irq handler function. Usually
this is what you want, but in some cases it would be helpful to use
some other data pointer.
Add a new function qdev_init_gpio_in_named_with_opaque() which allows
the caller to specify the data pointer they want.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-12-peter.maydell@linaro.org
The or-irq.h header file is missing the customary guard against
multiple inclusion, which means compilation fails if it gets
included twice. Fix the omission.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-11-peter.maydell@linaro.org
Move the definition of the struct for the unimplemented-device
from unimp.c to unimp.h, so that users can embed the struct
in their own device structs if they prefer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-10-peter.maydell@linaro.org
Create an "init-svtor" property on the armv7m container
object which we can forward to the CPU object.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-8-peter.maydell@linaro.org
Create an "idau" property on the armv7m container object which
we can forward to the CPU object. Annoyingly, we can't use
object_property_add_alias() because the CPU object we want to
forward to doesn't exist until the armv7m container is realized.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-6-peter.maydell@linaro.org
Add a function load_ramdisk_as() which behaves like the existing
load_ramdisk() but allows the caller to specify the AddressSpace
to use. This matches the pattern we have already for various
other loader functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-2-peter.maydell@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Allow the guest to determine the time set from the QEMU command line.
This includes adding a trace event to debug the new time.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initial commit of the ZynqMP RTC device.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
information
- remove s390x memory hotplug implementation, which is not useable in
this form
- add boot menu support in the s390-ccw bios
- expose s390x guest crash information
- fixes and cleaups
-----BEGIN PGP SIGNATURE-----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=chDT
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/cohuck/tags/s390x-20180301-v2' into staging
- add query-cpus-fast and deprecate query-cpus, while adding s390 cpu
information
- remove s390x memory hotplug implementation, which is not useable in
this form
- add boot menu support in the s390-ccw bios
- expose s390x guest crash information
- fixes and cleaups
# gpg: Signature made Thu 01 Mar 2018 12:54:47 GMT
# gpg: using RSA key DECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cohuck@redhat.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20180301-v2: (27 commits)
s390x/tcg: fix loading 31bit PSWs with the highest bit set
s390x: remove s390_get_memslot_count
s390x/sclp: remove memory hotplug support
s390x/cpumodel: document S390FeatDef.bit not applicable
hmp: change hmp_info_cpus to use query-cpus-fast
qemu-doc: deprecate query-cpus
qmp: add architecture specific cpu data for query-cpus-fast
qmp: add query-cpus-fast
qmp: expose s390-specific CPU info
s390x/tcg: add various alignment checks
s390x/tcg: fix disabling/enabling DAT
s390/stattrib: Make SaveVMHandlers data static
s390x/cpu: expose the guest crash information
pc-bios/s390: Rebuild the s390x firmware images with the boot menu changes
s390-ccw: interactive boot menu for scsi
s390-ccw: use zipl values when no boot menu options are present
s390-ccw: set cp_receive mask only when needed and consume pending service irqs
s390-ccw: read user input for boot index via the SCLP console
s390-ccw: print zipl boot menu
s390-ccw: read stage2 boot loader data to find menu
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Introduce two vhost-user meassges: VHOST_USER_CREATE_CRYPTO_SESSION
and VHOST_USER_CLOSE_CRYPTO_SESSION. At this point, the QEMU side
support crypto operation in cryptodev host-user backend.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Jay Zhou <jianjay.zhou@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Impliment the vhost-crypto's funtions, such as startup,
stop and notification etc. Introduce an enum
QCryptoCryptoDevBackendOptionsType in order to
identify the cryptodev vhost backend is vhost-user
or vhost-kernel-module (If exist).
At this point, the cryptdoev-vhost-user works.
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Signed-off-by: Jay Zhou <jianjay.zhou@huawei.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some devices need access to it.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Message-id: 20180227104903.21353-3-linus.walleij@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Ensure that the post write hook is called during reset. This allows us
to rely on the post write functions instead of having to call them from
the reset() function.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: d131e24b911653a945e46ca2d8f90f572469e1dd.1517856214.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJalWIkAAoJEHWtZYAqC0IRULsH/1qaCCDcR91PmBENdiYlsqvp
XyThlT1VtHhq66CJvH4RVwPhkSFGeMsElXhAk5KoQYha50LvJsqw5+RyXPPeCAk7
1k8nfUC2ELRsLofjee2XkENXA3f1EX0qz+D4ozWjoRt/bI0GtiuW+M1SlGZEiOWN
PbcB3XIESVdD1CXL+qlFQK6zHAG4mxVDaosYxACNJzsWIDoTOlyInCoNlkqknxsI
PffdbyZE5HZ6ANYkuKgOpXm9a5TmeqZl4MW+ikGG1D2S1QpUnRlTHKS3oDEA7NNb
9Z7jfZxOXCX5PxY04p1Bo0bgksDiQMqFCaIvYyKQ7aMjugvf56qnFJPx1Qx+0WE=
=Unmb
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stefanberger/tags/pull-tpm-2018-02-21-2' into staging
Merge tpm 2018/02/21 v2
# gpg: Signature made Tue 27 Feb 2018 13:50:28 GMT
# gpg: using RSA key 75AD65802A0B4211
# gpg: Good signature from "Stefan Berger <stefanb@linux.vnet.ibm.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B818 B9CA DF90 89C2 D5CE C66B 75AD 6580 2A0B 4211
* remotes/stefanberger/tags/pull-tpm-2018-02-21-2:
tests: add test for TPM TIS device
tests: Move common TPM test code into tpm-emu.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Due to a kernel bug we can never increase the size of capability
set 1, so introduce a new capability set in parallel, old userspace
will continue to use the old set, new userspace will start using
the new one when it detects a fixed kernel.
v2: don't use a define from virglrenderer, just probe it.
v3: fix compilation when virglrenderer disabled
v4: fix style warning, just use ?: op instead.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Message-id: 20180223023814.24459-1-airlied@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Not needed anymore after removal of the memory hotplug code.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
From an architecture point of view, nothing can be mapped into the address
space on s390x. All there is is memory. Therefore there is also not really
an interface to communicate such information to the guest. All we can do is
specify the maximum ram address and guests can probe in that range if
memory is available and usable (TPROT).
Also memory hotplug is strange. The guest can decide at some point in
time to add / remove memory in some range. While the hypervisor can deny
to online an increment, all increments have to be predefined and there is
no way of telling the guest about a newly "hotplugged" increment. So if we
specify right now e.g.
-m 2G,slots=2,maxmem=20G
An ordinary fedora guest will happily online (hotplug) all memory,
resulting in a guest consuming 20G. So it really behaves rather like
-m 22G
There is no way to hotplug memory from the outside like on other
architectures. This is of course bad for upper management layers.
As the guest can create/delete memory regions while it is running, of
course migration support is not available and tricky to implement.
With virtualization, it is different. We might want to map something
into guest address space (e.g. fake DAX devices) and not detect it
automatically as memory. So we really want to use the maxmem and slots
parameter just like on all other architectures. Such devices will have
to expose the applicable memory range themselves. To finally be able to
provide memory hotplug to guests, we will need a new paravirtualized
interface to do that (e.g. something into the direction of virtio-mem).
This implies, that maxmem cannot be used for s390x memory hotplug
anymore and has to go. This simplifies the code quite a bit.
As migration support is not working, this change cannot really break
migration as guests without slots and maxmem don't see the SCLP
features. Also, the ram size calculation does not change.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180219174231.10874-1-david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Matthew Rosato <mjrosato@linux.vnet.ibm.com>
[CH: tweaked patch description, as discussed on list]
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 20180215220540.6556-12-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
I/O currently being synchronous, there is no reason to ever clear the
SR_TXE bit. However the SR_TC bit may be cleared by software writing
to the SR register, so set it on each write.
In addition, fix the reset value of the USART status register.
Signed-off-by: Richard Braun <rbraun@sceen.net>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
[PMM: removed XXX tag from comment, since it isn't something
we need to come back and fix in QEMU]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move the TPM TIS related register and flag #defines into
include/hw/acpi/tpm.h for access by the test case.
Write a test case that covers the TIS functionality.
Add the tests cases to the MAINTAINERS file.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
PVRDMA is the QEMU implementation of VMware's paravirtualized RDMA device.
It works with its Linux Kernel driver AS IS, no need for any special
guest modifications.
While it complies with the VMware device, it can also communicate with
bare metal RDMA-enabled machines and does not require an RDMA HCA in the
host, it can work with Soft-RoCE (rxe).
It does not require the whole guest RAM to be pinned allowing memory
over-commit and, even if not implemented yet, migration support will be
possible with some HW assistance.
Implementation is divided into 2 components, rdma general and pvRDMA
specific functions and structures.
The second PVRDMA sub-module - interaction with PCI layer.
- Device configuration and setup (MSIX, BARs etc).
- Setup of DSR (Device Shared Resources)
- Setup of device ring.
- Device management.
Reviewed-by: Dotan Barak <dotanb@mellanox.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
RHEL6's compilers don't like the repeated typedef.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These devices are found in newer SoCs based on 440 core e.g. the 460EX
(http://www.embeddeddeveloper.com/assets/processors/amcc/datasheets/
PP460EX_DS2063.pdf)
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The spapr_vcpu_id() function is an accessor actually. Let's rename it
for symmetry with the recently added spapr_set_vcpu_id() helper.
The motivation behind this is that a later patch will consolidate
the VCPU id formula in a function and spapr_vcpu_id looks like an
appropriate name.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The VCPU ids are currently computed and assigned to each individual
CPU threads in spapr_cpu_core_realize(). But the numbering logic
of VCPU ids is actually a machine-level concept, and many places
in hw/ppc/spapr.c also have to compute VCPU ids out of CPU indexes.
The current formula used in spapr_cpu_core_realize() is:
vcpu_id = (cc->core_id * spapr->vsmt / smp_threads) + i
where:
cc->core_id is a multiple of smp_threads
cpu_index = cc->core_id + i
0 <= i < smp_threads
So we have:
cpu_index % smp_threads == i
cc->core_id / smp_threads == cpu_index / smp_threads
hence:
vcpu_id =
(cpu_index / smp_threads) * spapr->vsmt + cpu_index % smp_threads;
This formula was used before VSMT at the time VCPU ids where computed
at the target emulation level. It has the advantage of being useable
to derive a VPCU id out of a CPU index only. It is fitted for all the
places where the machine code has to compute a VCPU id.
This patch introduces an accessor to set the VCPU id in a PowerPCCPU object
using the above formula. It is a first step to consolidate all the VCPU id
logic in a single place.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Move necessary stuff in escc.h and update type names.
Remove slavio_serial_ms_kbd_init().
Fix code style problems reported by checkpatch.pl
Update mac_newworld, mac_oldworld and sun4m to use directly the
QDEV interface.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Peter Maydell
Eric Auger
David Gibson
BALATON Zoltan
Cédric Le Goater
Greg Kurz
Gerd Hoffmann
Mark Cave-Ayland
Kevin Wolf
Ross Zwisler
Paolo Bonzini
Philippe Mathieu-Daudé
Shannon Zhao
Tiwei Bie
Xiao Guangrong
Changpeng Liu
Alex Williamson
Paul Durrant
Peter Xu
Thomas Huth
Francisco Iglesias
Babu Moger
Geoffrey McRae
David Hildenbrand
Igor Mammedov
Michael Clark
Prem Mallappa
Claudio Imbrenda
Bharata B Rao
Ian Jackson
Ross Lagerwall
Dr. David Alan Gilbert
Wei Huang
Trent Piepho
Haozhong Zhang
Andrey Smirnov
Guenter Roeck
Wang Xin
Jason Baron
Alexey Kardashevskiy
Brijesh Singh
Nia Alarie
Suraj Jitindar Singh
Markus Armbruster
Alistair Francis
Gonglei
Corey Minyard
Dave Airlie
Cornelia Huck
Richard Braun
Stefan Berger
Yuval Shaia
Laurent Vivier