The following patch updates opentitan to match the new configuration,
as per, lowRISC/opentitan@217a0168ba
Note: with this patch we now skip the usage of the opentitan
`boot_rom`. The Opentitan boot rom contains hw verification
for devies which we are currently not supporting in qemu. As of now,
the `boot_rom` has no major significance, however, would be good to
support in the future.
Tested by running utests from the latest tock [1]
(that supports this version of OT).
[1] https://github.com/tock/tock/pull/3056
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220812005229.358850-1-wilfred.mallawa@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The 'fdt' param is not being used in riscv_setup_rom_reset_vec().
Simplify the API by removing it. While we're at it, remove the redundant
'return' statement at the end of function.
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Alistair Francis <alistair.francis@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Vijai Kumar K <vijai@behindbytes.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220728181926.2123771-1-danielhb413@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If the FDT contains /chosen/rng-seed, then the Linux RNG will use it to
initialize early. Set this using the usual guest random number
generation function. This is confirmed to successfully initialize the
RNG on Linux 5.19-rc2.
Cc: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220613115810.178210-1-Jason@zx2c4.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We previously stored the device tree at a 16MB alignment from the end of
memory (or 3GB). This means we need at least 16MB of memory to be able
to do this. We don't actually need the FDT to be 16MB aligned, so let's
drop it down to 2MB so that we can support systems with less memory,
while also allowing FDT size expansion.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/992
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-Id: <20220608062015.317894-1-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Various loader functions return an int which limits images to 2GB which
is fine for things like a BIOS/kernel image, but if we want to be able
to load memory images or large ramdisks then any file over 2GB would
silently fail to load.
Cc: Luc Michel <lmichel@kalray.eu>
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Luc Michel <lmichel@kalray.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20211111141141.3295094-2-jamie@nuviainc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
fw_cfg DT node is generated after the create_fdt without any check
if the DT is being loaded from the commandline. This results in
FDT_ERR_EXISTS error if dtb is loaded from the commandline.
Generate fw_cfg node only if the DT is not loaded from the commandline.
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220526203500.847165-1-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When both APLIC and IMSIC are present in virt machine, the APLIC should
be used as parent interrupt controller for dynamic platform devices.
In case of multiple sockets, we should prefer interrupt controller of
socket0 for dynamic platform devices.
Fixes: 3029fab643 ("hw/riscv: virt: Add support for generating
platform FDT entries")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220511144528.393530-9-apatel@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The QOM API already provides accessors for uint32 values, so reuse them.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220301225220.239065-3-shentey@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If specified CPU configuration is not valid, not just it prints error
message, it aborts and generates core dumps (depends on the operating
system). This kind of error handling should be used only when a serious
runtime error occurs.
This commit makes error handling on CPU configuration more generous on
sifive_e/u and opentitan machines. It now just prints error message and
quits (without coredumps and aborts).
This is separate from spike/virt because it involves different type
(TYPE_RISCV_HART_ARRAY) on sifive_e/u and opentitan machines.
Signed-off-by: Tsukasa OI <research_trasio@irq.a4lg.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <09e61e58a7543da44bdb0e0f5368afc8903b4aa6.1652509778.git.research_trasio@irq.a4lg.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If specified CPU configuration is not valid, not just it prints error
message, it aborts and generates core dumps (depends on the operating
system). This kind of error handling should be used only when a serious
runtime error occurs.
This commit makes error handling on CPU configuration more generous on
virt/spike machines. It now just prints error message and quits (without
coredumps and aborts).
Signed-off-by: Tsukasa OI <research_trasio@irq.a4lg.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <d17381d3ea4992808cf1894f379ca67220f61b45.1652509778.git.research_trasio@irq.a4lg.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Imply the TPM sysbus devices. This allows users to add TPM devices to
the RISC-V virt board.
This was tested by first creating an emulated TPM device:
swtpm socket --tpm2 -t -d --tpmstate dir=/tmp/tpm \
--ctrl type=unixio,path=swtpm-sock
Then launching QEMU with:
-chardev socket,id=chrtpm,path=swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-device tpm-tis-device,tpmdev=tpm0
The TPM device can be seen in the memory tree and the generated device
tree.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/942
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-7-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add support for plugging in devices, this was tested with the TPM
device.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-6-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Similar to the ARM virt machine add support for adding device tree
entries for dynamically created devices.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Message-Id: <20220427234146.1130752-5-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Create a platform bus to allow dynamic devices to be connected. This is
based on the ARM implementation.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-4-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Move the binary and device tree loading code to the machine done
notifier. This allows us to prepare for editing the device tree as part
of the notifier.
This is based on similar code in the ARM virt machine.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220427234146.1130752-2-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Commit 7c28f4da20 ("RISC-V: Don't add NULL bootargs to device-tree")
tried to avoid adding *NULL* bootargs to device tree, but unfortunately
the changes were entirely useless, due to MachineState::kernel_cmdline
can't be NULL at all as the default value is given as an empty string.
(see hw/core/machine.c::machine_initfn()).
Note the wording of *NULL* bootargs is wrong. It can't be NULL otherwise
a segfault had already been observed by dereferencing the NULL pointer.
It should be worded as *empty" bootargs.
Fixes: 7c28f4da20 ("RISC-V: Don't add NULL bootargs to device-tree")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220421055629.1177285-2-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the adding '/chosen/stdout-path' property in device tree
is determined by whether a kernel command line is provided, which is
wrong. It should be added unconditionally.
Fixes: 8d8897accb ("hw/riscv: spike: Allow using binary firmware as bios")
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220421055629.1177285-1-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The current riscv_load_fdt() forces fdt_load_addr to be placed at a dram address within 3GB,
but not all platforms have dram_base within 3GB.
This patch adds an exception for dram base not within 3GB,
which will place fdt at dram_end align 16MB.
riscv_setup_rom_reset_vec() also needs to be modified
Signed-off-by: Dylan Jhong <dylan@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220419115945.37945-1-dylan@andestech.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The device tree property "mmu-type" is currently exported as either
"riscv,sv32" or "riscv,sv48".
However, the riscv cpu device tree binding [1] has a specific value
"riscv,none" for a HART without a MMU.
Set the device tree property "mmu-type" to "riscv,none" when the CPU mmu
option is disabled using rv32,mmu=off or rv64,mmu=off.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/riscv/cpus.yaml?h=v5.17
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220414155510.1364147-1-niklas.cassel@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The -bios option is silently ignored if used in combination with -enable-kvm.
The reason is that the machine starts in S-Mode, and the bios typically runs in
M-Mode.
Better exit in that case to not confuse the user.
Signed-off-by: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-Id: <20220401121842.2791796-1-ralf.ramsauer@oth-regensburg.de>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch updates the SPI_DEVICE, SPI_HOST0, SPI_HOST1
base addresses. Also adds these as unimplemented devices.
The address references can be found [1].
[1] 6c317992fb/hw/top_earlgrey/sw/autogen/top_earlgrey_memory.h (L107)
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220218063839.405082-1-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
To facilitate software development of RISC-V systems with large number
of HARTs, we increase the maximum number of allowed CPUs to 512 (2^9).
We also add a detailed source level comments about limit defines which
impact the physical address space utilization.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-Id: <20220220085526.808674-6-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate both AIA IMSIC and AIA APLIC
devices only when "aia=aplic-imsic" parameter is passed along
with machine name in the QEMU command-line. The AIA IMSIC is
only a per-HART MSI controller so we use AIA APLIC in MSI-mode
to forward all wired interrupts as MSIs to the AIA IMSIC.
We also provide "aia-guests=<xyz>" parameter which can be used
to specify number of VS-level AIA IMSIC Guests MMIO pages for
each HART.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220220085526.808674-4-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate AIA APLIC devices only when
"aia=aplic" parameter is passed along with machine name in QEMU
command-line. When "aia=none" or not specified then we fallback
to original PLIC device emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220220085526.808674-2-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We should use the AIA INTC compatible string in the CPU INTC
DT nodes when the CPUs support AIA feature. This will allow
Linux INTC driver to use AIA local interrupt CSRs.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-id: 20220204174700.534953-17-anup@brainfault.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Now that RISC-V Spike machine can use BIN BIOS images, we remove
the macros used for ELF BIOS image names.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, we have to use OpenSBI firmware ELF as bios for the spike
machine because the HTIF console requires ELF for parsing "fromhost"
and "tohost" symbols.
The latest OpenSBI can now optionally pick-up HTIF register address
from HTIF DT node so using this feature spike machine can now use
OpenSBI firmware BIN as bios.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Get kernel and fdt start address in virt.c, and pass them to KVM
when cpu reset. Add kvm_riscv.h to place riscv specific interface.
In addition, PLIC is created without M-mode PLIC contexts when KVM
is enabled.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Mingwang Li <limingwang@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-id: 20220112081329.1835-7-jiangyifei@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The following change was made to rectify incorrectly set stride length
on the PLIC [1]. Where it should be 32bit and not 24bit (0x18). This was
discovered whilst attempting to fix a bug where a timer_interrupt was
not serviced on TockOS-OpenTitan.
[1] https://docs.opentitan.org/hw/top_earlgrey/ip_autogen/rv_plic/doc/
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Tested-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20220111071025.4169189-1-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When realising the SoC use error_fatal instead of error_abort as the
process can fail and report useful information to the user.
Currently a user can see this:
$ ../qemu/bld/qemu-system-riscv64 -M sifive_u -S -monitor stdio -display none -drive if=pflash
QEMU 6.1.93 monitor - type 'help' for more information
(qemu) Unexpected error in sifive_u_otp_realize() at ../hw/misc/sifive_u_otp.c:229:
qemu-system-riscv64: OTP drive size < 16K
Aborted (core dumped)
Which this patch addresses
Reported-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220105213937.1113508-8-alistair.francis@opensource.wdc.com>
The original BBL boot method had the kernel embedded as an opaque blob
that was blindly jumped to, which OpenSBI implemented as fw_payload.
OpenSBI then implemented fw_jump, which allows the payload to be loaded
elsewhere, but still blindly jumps to a fixed address at which the
kernel is to be loaded. Finally, OpenSBI introduced fw_dynamic, which
allows the previous stage to inform it where to jump to, rather than
having to blindly guess like fw_jump, or embed the payload as part of
the build like fw_payload. When used with an opaque binary (i.e. the
output of objcopy -O binary), it matches the behaviour of the previous
methods. However, when used with an ELF, QEMU currently passes on the
ELF's entry point address, which causes a discrepancy compared with all
the other boot methods if that entry point is not the first instruction
in the binary.
This difference specific to fw_dynamic with an ELF is not apparent when
booting Linux, since its entry point is the first instruction in the
binary. However, FreeBSD has a separate ELF entry point, following the
calling convention used by its bootloader, that differs from the first
instruction in the binary, used for the legacy SBI entry point, and so
the specific combination of QEMU's default fw_dynamic firmware with
booting FreeBSD as an ELF rather than a raw binary does not work.
Thus, align the behaviour when loading an ELF with the behaviour when
loading a raw binary; namely, use the base address of the loaded kernel
in place of the entry point.
The uImage code is left as-is in using the U-Boot header's entry point,
since the calling convention for that entry point is the same as the SBI
one and it mirrors what U-Boot will do.
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20211214032456.70203-1-jrtc27@jrtc27.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
drive_get_next() is basically a bad idea. It returns the "next" block
backend of a certain interface type. "Next" means bus=0,unit=N, where
subsequent calls count N up from zero, per interface type.
This lets you define unit numbers implicitly by execution order. If the
order changes, or new calls appear "in the middle", unit numbers change.
ABI break. Hard to spot in review.
A number of machines connect just one backend with drive_get_next().
Change them to use drive_get() directly. This makes the (zero) unit
number explicit in the code.
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Cc: Niek Linnenbank <nieklinnenbank@gmail.com>
Cc: Andrew Baumann <Andrew.Baumann@microsoft.com>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: Jean-Christophe Dubois <jcd@tribudubois.net>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Artyom Tarasenko <atar4qemu@gmail.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Laurent Vivier <laurent@vivier.eu>
Cc: qemu-arm@nongnu.org
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-3-armbru@redhat.com>
ssi_sd_realize() creates an "sd-card" device. This is inappropriate,
and marked FIXME.
Move it to the boards that create these devices. Prior art: commit
eb4f566bbb for device "generic-sdhci", and commit 26c607b86b for
device "pl181".
The device remains not user-creatable, because its users should (and
do) wire up its GPIO chip-select line.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Alistair Francis <Alistair.Francis@wdc.com>
Cc: Bin Meng <bin.meng@windriver.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: "Philippe Mathieu-Daudé" <f4bug@amsat.org>
Cc: qemu-arm@nongnu.org
Cc: qemu-riscv@nongnu.org
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20211117163409.3587705-2-armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Fixup the PLIC context address to correctly support the threshold and
claim register.
Fixes: ef63100648 ("hw/riscv: opentitan: Update to the latest build")
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211025040657.262696-1-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-5-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-4-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-3-alistair.francis@opensource.wdc.com
Add a generic function that can create the PLIC strings.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20211022060133.3045020-2-alistair.francis@opensource.wdc.com
Using a macro for the PLIC configuration doesn't make the code any
easier to read. Instead it makes it harder to figure out what is going
on, so let's remove it.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20211022060133.3045020-1-alistair.francis@opensource.wdc.com
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211020014112.7336-7-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211020014112.7336-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
While at it add check for user supplied RAM size and error out if it
mismatches board expected value.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20211020014112.7336-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211020014112.7336-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
While at it add check for user supplied RAM size and error out if it
mismatches board expected value.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20211020014112.7336-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Using memory_region_init_ram(), which can't possibly handle vhost-user,
and can't work as expected with '-numa node,memdev' options.
Use MachineState::ram instead of manually initializing RAM memory
region, as well as by providing MachineClass::default_ram_id to
opt in to memdev scheme.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20211020014112.7336-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Shortly, the set of supported XL will not be just 32 and 64,
and representing that properly using the enumeration will be
imperative.
Two places, booting and gdb, intentionally use misa_mxl_max
to emphasize the use of the reset value of misa.mxl, and not
the current cpu state.
Reviewed-by: LIU Zhiwei <zhiwei_liu@c-sky.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20211020031709.359469-5-richard.henderson@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
If default main_mem is used to be registered as the system memory,
other memory cannot be initialized. Therefore, the system memory
should be initialized to the machine->ram, which consists of the
default main_mem and other possible memory required by applications,
such as shared hugepage memory in DPDK.
Also, the mc->defaul_ram_id should be set to the default main_mem,
such as "riscv_virt_board.ram" for the virt machine.
Signed-off-by: Mingwang Li <limingwang@huawei.com>
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20211016030908.40480-1-limingwang@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Mark the shakti_c machine as not user creatable.
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/639
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <c617a04d4e3dd041a3427b47a1b1d5ab475a2edd.1632871759.git.alistair.francis@wdc.com>
We extend virt machine to emulate ACLINT devices only when "aclint=on"
parameter is passed along with machine name in QEMU command-line.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-5-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We re-factor and break the FDT generation into smaller functions
so that it is easier to modify FDT generation for different
configurations of virt machine.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-4-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V ACLINT is more modular and backward compatible with
original SiFive CLINT so instead of duplicating the original
SiFive CLINT implementation we upgrade the current SiFive CLINT
implementation to RISC-V ACLINT implementation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-3-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We will be upgrading SiFive CLINT implementation into RISC-V ACLINT
implementation so let's first rename the sources.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 20210831110603.338681-2-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the timer MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 84d5b1d5783d2e79eee69a2f7ac480cc0c070db3.1630301632.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the external MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 0364190bfa935058a845c0fa1ecf650328840ad5.1630301632.git.alistair.francis@wdc.com
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the external MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 0a76946981852f5bd15f0c37ab35b253371027a8.1630301632.git.alistair.francis@wdc.com
In the riscv virt machine init function, We assemble a string
plic_hart_config which is a comma-separated list of N copies of the
VIRT_PLIC_HART_CONFIG string. The code that does this has a
misunderstanding of the strncat() length argument. If the source
string is too large strncat() will write a maximum of length+1 bytes
(length bytes from the source string plus a trailing NUL), but the
code here assumes that it will write only length bytes at most.
This isn't an actual bug because the code has correctly precalculated
the amount of memory it needs to allocate so that it will never be
too small (i.e. we could have used plain old strcat()), but it does
mean that the code looks like it has a guard against accidental
overrun when it doesn't.
Rewrite the string handling here to use the glib g_strjoinv()
function, which means we don't need to do careful accountancy of
string lengths, and makes it clearer that what we're doing is
"create a comma-separated string".
Fixes: Coverity 1460752
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210812144647.10516-1-peter.maydell@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The flash is not inside the SoC, so it's inappropriate to put it
under the /soc node. Move it to root instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210807035641.22449-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Use a dedicated UART config(CONFIG_SHAKTI_UART) to select
shakti uart.
Signed-off-by: Vijai Kumar K <vijai@behindbytes.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210731190229.137483-1-vijai@behindbytes.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
arch_init.h only defines the QEMU_ARCH_* enumeration and the
arch_type global. Don't include it in files that don't use those.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210730105947.28215-8-peter.maydell@linaro.org
Only the Virt and Spike machines use NUMA. Add a RISCV_NUMA Kconfig
symbol and only have these machines select it. Adapt the Meson file
to only built it if required.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210515173716.358295-8-philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Coverity reports that we don't check the error result of fdt_pack(), so
let's save the result and assert that it is 0.
Fixes: Coverity CID 1458136
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 07325315b49d5555269f76094e4bc5296e0643b9.1626303527.git.alistair.francis@wdc.com
Currently the firmware dynamic info (fw_dyn) is put right after
the reset vector, which is not 8-byte aligned on RV64. OpenSBI
fw_dynamic uses ld to read contents from 'struct fw_dynamic_info',
which expects fw_dyn to be on the 8-byte boundary, otherwise the
misaligned load exception may happen. Fortunately this does not
cause any issue on QEMU, as QEMU does support misaligned load.
RV32 does not have any issue as it is 4-byte aligned already.
Change to make sure it is 8-byte aligned which works for both
RV32 and RV64.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210708143319.10441-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the CLINT timebase frequency is set to 10MHz on sifive_u,
but on the real hardware the timebase frequency is 1Mhz.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210706102616.1922469-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Connect the Ibex timer to the OpenTitan machine. The timer can trigger
the RISC-V MIE interrupt as well as a custom device interrupt.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 5e7f4e9b4537f863bcb8db1264b840b56ef2a929.1624001156.git.alistair.francis@wdc.com
At present the Microchip Icicle Kit machine only supports using
'-bios' to load the HSS, and does not support '-kernel' for direct
kernel booting just like other RISC-V machines do. One has to use
U-Boot which is chain-loaded by HSS, to load a kernel for testing.
This is not so convenient.
Adding '-kernel' support together with the existing '-bios', we
follow the following table to select which payload we execute:
-bios | -kernel | payload
------+------------+--------
N | N | HSS
Y | don't care | HSS
N | Y | kernel
This ensures backwards compatibility with how we used to expose
'-bios' to users. When '-kernel' is used for direct boot, '-dtb'
must be present to provide a valid device tree for the board,
as we don't generate device tree.
When direct kernel boot is used, the OpenSBI fw_dynamic BIOS image
is used to boot a payload like U-Boot or OS kernel directly.
Documentation is updated to describe the direct kernel boot. Note
as of today there is still no PolarFire SoC support in the upstream
Linux kernel hence the document does not include instructions for
that. It will be updated in the future.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-8-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The OpenSBI BIOS image names are used by many RISC-V machines.
Let's define macros for them.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-7-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The official DT bindings of PLIC uses "sifive,plic-1.0.0" as the
compatible string in the upstream Linux kernel. "riscv,plic0" is
now legacy and has to be kept for backward compatibility of legacy
systems.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Linux kernel commit a2770b57d083 ("dt-bindings: timer: Add CLINT bindings")
adds the official DT bindings for CLINT, which uses "sifive,clint0"
as the compatible string. "riscv,clint0" is now legacy and has to
be kept for backward compatibility of legacy systems.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Since commit 78da6a1bca ("device_tree: add qemu_fdt_setprop_string_array helper"),
we can use the new helper to set the compatible strings for the
SiFive test device node.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Since commit 78da6a1bca ("device_tree: add qemu_fdt_setprop_string_array helper"),
we can use the new helper to set the clock name for the ethernet
controller node.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210430071302.1489082-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
imply VIRTIO_VGA for the virt machine, this fixes the following error
when specifying `-vga virtio` as a command line argument:
qemu-system-riscv64: Virtio VGA not available
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 7ac26fafee8bd59d2a0640f3233f8ad1ab270e1e.1617367317.git.alistair.francis@wdc.com
Update the OpenTitan interrupt layout to match the latest OpenTitan
bitstreams. This involves changing the Ibex PLIC memory layout and the
UART interrupts.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: e92b696f1809c9fa4410da2e9f23c414db5a6960.1617202791.git.alistair.francis@wdc.com
Connect one shakti uart to the shakti_c machine.
Signed-off-by: Vijai Kumar K <vijai@behindbytes.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210401181457.73039-5-vijai@behindbytes.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This was accidentally dropped before. Add it back.
Fixes: 732612856a ("hw/riscv: Drop 'struct MemmapEntry'")
Reported-by: Emmanuel Blot <eblot.ml@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210331103612.654261-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Stop including exec/address-spaces.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-5-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include qemu/log.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210328054833.2351597-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Many files include hw/irq.h without needing it. Remove the superfluous
include statements.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20210327050236.2232347-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Since HSS commit c20a89f8dcac, the Icicle Kit reference design has
been updated to use a register mapped at 0x4f000000 instead of a
GPIO to control whether eMMC or SD card is to be used. With this
support the same HSS image can be used for both eMMC and SD card
boot flow, while previously two different board configurations were
used. This is undocumented but one can take a look at the HSS code
HSS_MMCInit() in services/mmc/mmc_api.c.
With this commit, HSS image built from 2020.12 release boots again.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210322075248.136255-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Provides fw_cfg for the virt machine on riscv. This enables
using e.g. ramfb later.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210318235041.17175-2-ashe@kivikakk.ee
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmBI50MACgkQ+9DbCVqe
KkSyKggAhPZW+7sReVEsFdnVfwuo3evW7auoW44mghNbikTnm3RfoahYTrek8lGZ
AEo2gFMbzENW0j88e0OvSYYtwkVz3sD68bygfXerti6sQwWlwkf42I/suWjJNLph
oVKGEEdJess9+zR13Cu6RAq5RaTwzDPGPjUwTbeJPpAps4+UZV3hsxhaxs8keII6
GBa/idnh0qEApP2NDLKiSASrYZM7xGvljE7zO4qhchd6iSH/o5rCtkoB2tRCcXGo
+KF8LyBsUNf7GiWp0yYZMZUQ3Pqskqma8N3d2A4UlS1kXvxeX/FiORkG/Ne8bH1Z
VZ1Z/xbyXGlVkiP1bcoYSc6XWHNDTw==
=R9zQ
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2' into staging
Testing, guest-loader and other misc tweaks
- add warning text to quickstart example
- add CFI tests to CI
- use --arch-only for docker pre-requisites
- fix .editorconfig for emacs
- add guest-loader for Xen-like hypervisor testing
- move generic-loader docs into manual proper
- move semihosting out of hw/
# gpg: Signature made Wed 10 Mar 2021 15:35:31 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-docs-xen-updates-100321-2:
semihosting: Move hw/semihosting/ -> semihosting/
semihosting: Move include/hw/semihosting/ -> include/semihosting/
tests/avocado: add boot_xen tests
docs: add some documentation for the guest-loader
docs: move generic-loader documentation into the main manual
hw/core: implement a guest-loader to support static hypervisor guests
device_tree: add qemu_fdt_setprop_string_array helper
hw/riscv: migrate fdt field to generic MachineState
hw/board: promote fdt from ARM VirtMachineState to MachineState
.editorconfig: update the automatic mode setting for Emacs
tests/docker: Use --arch-only when building Debian cross image
gitlab-ci.yml: Add jobs to test CFI flags
gitlab-ci.yml: Allow custom # of parallel linkers
tests/docker: add a test-tcg for building then running check-tcg
docs/system: add a gentle prompt for the complexity to come
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a mechanical change to make the fdt available through
MachineState.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210303173642.3805-3-alex.bennee@linaro.org>
There are 23 files that include the "sysemu/qtest.h",
but they do not use any qtest functions.
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20210226081414.205946-1-kuhn.chenqun@huawei.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Some peripherals require 64-bit PCI address, so let's map the high
mmio space for PCIe.
For RV32, the address is hardcoded to below 4 GiB from the highest
accessible physical address. For RV64, the base address depends on
top of RAM and is aligned to its size which is using 16 GiB for now.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
RV32 supports 34-bit physical address hence the maximum RAM size
should be limited. Limit the RAM size to 10 GiB, which leaves
some room for PCIe high mmio space.
For 32-bit host, this is not needed as machine->ram_size cannot
represent a RAM size that big. Use a #if size test to only do
the size limitation for the 64-bit host.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-4-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
`link_up` is never used in gpex_pcie_init(). Drop it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210220144807.819-3-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is already a MemMapEntry type defined in hwaddr.h. Let's drop
the RISC-V defined `struct MemmapEntry` and use the existing one.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20210220144807.819-2-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI2 controller to the SoC, and connects an SD
card to it. The generation of corresponding device tree source
fragment is also added.
Specify machine property `msel` to 11 to boot the same upstream
U-Boot SPL and payload image for the SiFive HiFive Unleashed board.
Note subsequent payload is stored in the SD card image.
$ qemu-system-riscv64 -nographic -M sifive_u,msel=11 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=sdcard.img,if=sd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-6-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This adds the QSPI0 controller to the SoC, and connects an ISSI
25WP256 flash to it. The generation of corresponding device tree
source fragment is also added.
Since the direct memory-mapped mode is not supported by the SiFive
SPI model, the <reg> property does not populate the second group
which represents the memory mapped address of the SPI flash.
With this commit, upstream U-Boot for the SiFive HiFive Unleashed
board can boot on QEMU 'sifive_u' out of the box. This allows users
to develop and test the recommended RISC-V boot flow with a real
world use case: ZSBL (in QEMU) loads U-Boot SPL from SPI flash to
L2LIM, then U-Boot SPL loads the payload from SPI flash that is
combined with OpenSBI fw_dynamic firmware and U-Boot proper.
Specify machine property `msel` to 6 to allow booting from the SPI
flash. U-Boot spl is directly loaded via `-bios`, and subsequent
payload is stored in the SPI flash image. Example command line:
$ qemu-system-riscv64 -nographic -M sifive_u,msel=6 -smp 5 -m 8G \
-bios u-boot-spl.bin -drive file=spi-nor.img,if=mtd
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210126060007.12904-5-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We were accidently passing RISCVHartArrayState by value instead of
pointer. The type is 824 bytes long so let's correct that and pass it by
pointer instead.
Fixes: Coverity CID 1438099
Fixes: Coverity CID 1438100
Fixes: Coverity CID 1438101
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Message-id: f3e04424723e0e222769991896cc82308fd23f76.1610751609.git.alistair.francis@wdc.com
SIFIVE_U_CPU is conditionally set to SIFIVE_U34 or SIFIVE_U54, hence
there is no need to use #idef to set the mc->default_cpu_type.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210109143637.29645-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, we place the DTB at 2MB from 4GB or end of DRAM which ever is
lesser. However, Linux kernel can address only 1GB of memory for RV32.
Thus, it can not map anything beyond 3GB (assuming 2GB is the starting address).
As a result, it can not process DT and panic if opensbi dynamic firmware
is used. While at it, place the DTB further away to avoid in memory placement
issues in future.
Fix this by placing the DTB at 16MB from 3GB or end of DRAM whichever is lower.
Fixes: 66b1205bc5 ("RISC-V: Copy the fdt in dram instead of ROM")
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Message-id: 20210107091127.3407870-1-atish.patra@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of using string compares to determine if a RISC-V machine is
using 32-bit or 64-bit CPUs we can use the initalised CPUs. This avoids
us having to maintain a list of CPU names to compare against.
This commit also fixes the name of the function to match the
riscv_cpu_is_32bit() function.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 8ab7614e5df93ab5267788b73dcd75f9f5615e82.1608142916.git.alistair.francis@wdc.com
Currently the riscv_is_32_bit() function only supports the generic rv32
CPUs. Extend the function to support the SiFive and LowRISC CPUs as
well.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Message-id: 9a13764115ba78688ba61b56526c6de65fc3ef42.1608142916.git.alistair.francis@wdc.com
The sifive_u machine emulates two UARTs but we have only UART0 DT
node in the generated DTB so this patch adds UART1 DT node in the
generated DTB.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201111094725.3768755-1-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Machine options can be retrieved as properties of the machine object.
Encourage that by removing the "easy" accessor to machine options.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The latest SD card image [1] released by Microchip ships a Linux
kernel with built-in PolarFire SoC I2C driver support. The device
tree file includes the description for the I2C1 node hence kernel
tries to probe the I2C1 device during boot.
It is enough to create an unimplemented device for I2C1 to allow
the kernel to continue booting to the shell.
[1] ftp://ftpsoc.microsemi.com/outgoing/core-image-minimal-dev-icicle-kit-es-sd-20201009141623.rootfs.wic.gz
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-11-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When system memory is larger than 1 GiB (high memory), PolarFire SoC
maps it at address 0x10_0000_0000. Address 0xC000_0000 and above is
aliased to the same 1 GiB low memory with different cache attributes.
At present QEMU maps the system memory contiguously from 0x8000_0000.
This corrects the wrong QEMU logic. Note address 0x14_0000_0000 is
the alias to the high memory, and even physical memory is only 1 GiB,
the HSS codes still tries to probe the high memory alias address.
It seems there is no issue on the real hardware, so we will have to
take that into the consideration in our emulation. Due to this, we
we increase the default system memory size to 1537 MiB (the minimum
required high memory size by HSS) so that user gets notified an error
when less than 1537 MiB is specified.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201101170538.3732-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Somehow HSS needs to access address 0 [1] for the DDR calibration data
which is in the chipset's reserved memory. Let's map it.
[1] See the config_copy() calls in various places in ddr_setup() in
the HSS source codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-9-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously SYSREG was created as an unimplemented device. Now that
we have a simple SYSREG module, connect it.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-8-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Previously IOSCB_CFG was created as an unimplemented device. With
the new IOSCB model, its memory range is already covered by the
IOSCB hence remove the previous unimplemented device creation in
the SoC codes.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-6-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Connect DDR SGMII PHY module and CFG module to the PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-4-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
It is not easy to find out the memory map for a specific component
in the PolarFire SoC as the information is scattered in different
documents. Add some comments so that people can know where to get
such information from the Microchip website.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 1603863010-15807-2-git-send-email-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Extend virt machine to allow passing custom DTB using "-dtb"
command-line parameter. This will help users pass modified DTB
to virt machine.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201022053225.2596110-2-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Extend sifive_u machine to allow passing custom DTB using "-dtb"
command-line parameter. This will help users pass modified DTB
or Linux SiFive DTB to sifive_u machine.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201022053225.2596110-1-anup.patel@wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of loading the kernel at a hardcoded start address, let's load
the kernel at the next aligned address after the end of the firmware.
This should have no impact for current users of OpenSBI, but will
allow loading a noMMU kernel at the start of memory.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 46c00c4f15b42feb792090e3d74359e180a6d954.1602634524.git.alistair.francis@wdc.com
Instead of returning the unused entry address from riscv_load_firmware()
instead return the end address. Also return the end address from
riscv_find_and_load_firmware().
This tells the caller if a firmware was loaded and how big it is. This
can be used to determine the load address of the next image (usually the
kernel).
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: 558cf67162342d65a23262248b040563716628b2.1602634524.git.alistair.francis@wdc.com
Allow the user to specify the main application CPU for the sifive_u
machine.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Palmer Dabbelt <palmerdabbelt@google.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Message-id: b8412086c8aea0eff30fb7a17f0acf2943381b6a.1602634524.git.alistair.francis@wdc.com
Several callers of load_elf() pass pointers for lowaddr and highaddr
parameters which are then not used for anything. This may stem from a
misunderstanding that load_elf need a value here but in fact it can
take NULL to ignore these values. Remove such unused variables and
pass NULL instead from callers that don't need these.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Message-Id: <20200705174020.BDD0174633F@zero.eik.bme.hu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200921221045.699690-25-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Class properties make QOM introspection simpler and easier, as
they don't require an object to be instantiated.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200921221045.699690-24-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with the QOM type check
macros (SIFIVE_U_OTP, SIFIVE_U_PRCI). This needs to be addressed
to allow us to transform the QOM type check macros into functions
generated by OBJECT_DECLARE_TYPE().
Rename all the constants to SIFIVE_U_DEV_*, to avoid conflicts.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200911173447.165713-3-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Some of the enum constant names conflict with a QOM type check
macro (SIFIVE_E_PRCI). This needs to be addressed to allow us to
transform the QOM type check macros into functions generated by
OBJECT_DECLARE_TYPE().
Rename all the constants to SIFIVE_E_DEV_*, to avoid conflicts.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20200911173447.165713-2-ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
At present the Kconfig file is in disorder. Let's sort the options.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-13-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The name SIFIVE is too vague to convey the required component of
MSI_NONBROKEN. Let's drop the option, and select MSI_NONBROKEN in
each machine instead.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-12-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Every RISC-V machine needs riscv_hart hence there is no need to
have a dedicated Kconfig option for it. Drop the Kconfig option
and always build riscv_hart.c.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_test model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-10-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_uart model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-9-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move riscv_htif model to hw/char directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-8-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_plic model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_clint model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-6-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_gpio model to hw/gpio directory.
Note this also removes the trace-events in the hw/riscv directory,
since gpio is the only supported trace target in that directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-5-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_otp model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-4-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_u_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-3-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_e_prci model to hw/misc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-2-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
SiFive FU540 SoC integrates a platform DMA controller with 4 DMA
channels. This connects the exsiting SiFive PDMA model to the SoC,
and adds its device tree data as well.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-17-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present the CLINT timestamp is using a hard-coded timebase
frequency value SIFIVE_CLINT_TIMEBASE_FREQ. This might not be
true for all boards.
Add a new 'timebase-freq' property to the CLINT device, and
update various functions to accept this as a parameter.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-16-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates 3 GPIOs controllers. It seems
enough to create unimplemented devices to cover their register
spaces at this point.
With this commit, QEMU can boot to U-Boot (2nd stage bootloader)
all the way to the Linux shell login prompt, with a modified HSS
(1st stage bootloader).
For detailed instructions on how to create images for the Icicle
Kit board, please check QEMU RISC-V WiKi page at:
https://wiki.qemu.org/Documentation/Platforms/RISCV
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-15-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Microchip PolarFire SoC integrates 2 Candence GEMs to provide
IEEE 802.3 standard-compliant 10/100/1000 Mbps ethernet interface.
On the Icicle Kit board, GEM0 connects to a PHY at address 8 while
GEM1 connects to a PHY at address 9.
The 2nd stage bootloader (U-Boot) is using GEM1 by default, so we
must specify 2 '-nic' options from the command line in order to get
a working ethernet.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1598924352-89526-14-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
On the Icicle Kit board, the HSS firmware utilizes the on-chip DMA
controller to move the 2nd stage bootloader in the system memory.
Let's connect a DMA controller to Microchip PolarFire SoC.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1598924352-89526-11-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
