Implement a model of the TrustZone Master Securtiy Controller,
as documented in the Arm CoreLink SIE-200 System IP for
Embedded TRM (DDI0571G):
https://developer.arm.com/products/architecture/m-profile/docs/ddi0571/g
The MSC is intended to sit in front of a device which can
be a bus master (eg a DMA controller) and programmably gate
its transactions. This allows a bus-mastering device to be
controlled by non-secure code but still restricted from
making accesses to addresses which are secure-only.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180820141116.9118-12-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Implement the IoTKit system control element's system information
block; this is just a pair of read-only version/config registers,
plus the usual PID/CID ID registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-10-peter.maydell@linaro.org
The Arm IoTKit includes a system control element which
provides a block of read-only ID registers and a block
of read-write control registers. Implement a minimal
version of this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-9-peter.maydell@linaro.org
In the MPS2 FPGAIO, PSCNTR is a free-running downcounter with
a reload value configured via the PRESCALE register, and
COUNTER counts up by 1 every time PSCNTR reaches zero.
Implement these counters.
We can just increment the counters migration subsection's
version ID because we only added it in the previous commit,
so no released QEMU versions will be using it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-3-peter.maydell@linaro.org
The MPS2 FPGAIO block includes some simple free-running counters.
Implement these.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-2-peter.maydell@linaro.org
It was not possible to compile out pvpanic. Use the same trick
than applesmc.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
The mmio_interface device was a purely internal artifact
of the implementation of the memory subsystem's request_ptr
APIs. Now that we have removed those APIs, we can remove
the mmio_interface device too.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Message-id: 20180817114619.22354-4-peter.maydell@linaro.org
This will be used to construct a memory region beyond the RAM region
to let firmwares scan the address space with load/store to guess how
much RAM the SoC has.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-7-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This fixes the intended protection of read-only values in the
configuration register. They were being always set to zero by mistake.
The read-only fields depend on the configured memory size of the system,
so they cannot be fixed at compile time. The most straight forward
option was to store them in the state structure.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-3-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SDMC on the ast2500 has 170 registers.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20180807075757.7242-2-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
aux_create_slave() calls qdev_init_nofail() which in turn "realizes"
the corresponding object. This is unlike qdev_create(), and it is wrong
because qdev_init_nofail() must not be called from an instance_init
function. Move qdev_init_nofail() and the subsequent aux_map_slave into
the caller's realize function.
There are two more bugs that needs to be fixed here, too, where the
objects are created but not added as children. Therefore when
you call object_unparent on them, nothing happens.
In particular dpcd and edid give you an infinite loop in bus_unparent,
because device_unparent is not called and does not remove them from
the list of devices on the bus.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 1531745974-17187-17-git-send-email-thuth@redhat.com
[thuth: Added Paolo's fixup for the dpcd and edid unparenting]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 SoC family changes the runtime behaviour of the hardware
strapping register (SCU70) to write-1-set/write-1-clear, with
write-1-clear implemented on the "read-only" SoC revision register
(SCU7C). For the the AST2400, the hardware strapping is
runtime-configured with read-modify-write semantics.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20180709143524.17480-1-andrew@aj.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All Aspeed SoC clocks are driven by an input source clock which can
have different frequencies : 24MHz or 25MHz, and also, on the Aspeed
AST2400 SoC, 48MHz. The H-PLL (CPU) clock is defined from a
calculation using parameters in the H-PLL Parameter register or from a
predefined set of frequencies if the setting is strapped by hardware
(Aspeed AST2400 SoC). The other clocks of the SoC are then defined
from the H-PLL using dividers.
We introduce first the APB clock because it should be used to drive
the Aspeed timer model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 20180622075700.5923-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement the SECMPCINTSTATUS register. This is the only register
in the security controller that deals with Memory Protection
Controllers, and it simply provides a read-only view of the
interrupt lines from the various MPCs in the system.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180620132032.28865-6-peter.maydell@linaro.org
Implement the missing registers for the TZ MPC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-3-peter.maydell@linaro.org
Implement the Arm TrustZone Memory Protection Controller, which sits
in front of RAM and allows secure software to configure it to either
pass through or reject transactions.
We implement the MPC as a QEMU IOMMU, which will direct transactions
either through to the devices and memory behind it or to a special
"never works" AddressSpace if they are blocked.
This initial commit implements the skeleton of the device:
* it always permits accesses
* it doesn't implement most of the registers
* it doesn't implement the interrupt or other behaviour
for blocked transactions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20180620132032.28865-2-peter.maydell@linaro.org
In the case where we have an interrupt generated externally from inputs to
bits 1 and 2 of port A and/or port B, it is necessary to expose
mos6522_update_irq() so it can be called by the interrupt source.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The PMU device supercedes the CUDA device found on older New World Macs and
is supported by a larger number of guest OSs from OS 9 to OS X 10.5.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
PMU-enabled New World Macs expose their GPIOs via a separate memory region
within the macio device.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This option allows the VIA configuration to be controlled between 3
different possible setups: cuda, pmu-adb and pmu with USB rather than ADB
keyboard/mouse.
For the moment we don't do anything with the configuration except to pass
it to the macio device (the via-cuda parent) and also to the firmware via
the fw_cfg interface so that it can present the correct device tree.
The default is cuda which is the current default and so will have no
change in behaviour.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The 6522 VIA timer frequency cannot be set by altering registers within the
device itself and hence it is a fixed property of the machine.
Move the initialisation of the timer frequency to the mos6522 reset function
and ensure that any subclasses always call the parent reset function so that
it isn't required to store the timer frequency within vmstate_mos6522_timer
itself.
By moving the frequency initialisation to the device reset function then we
find that the realize function for both mos6522 and mos6522_cuda becomes
obsolete and can simply be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Examining the migration stream it can be seen that the mos6522 device state is
being stored separately rather than as part of the CUDA device which is
incorrect (and likely to cause issues if another mos6522 device is added to
the machine).
Resolve this by embedding the mos6522_cuda device directly within the CUDA
device rather than using a QOM object link to reference the device separately.
Note that we also bump the version in vmstate_cuda to reflect this change: this
isn't particularly important for the moment as the Mac machine migration isn't
100% reliable due to issues migrating the timebase under TCG.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Specs are available here :
https://www.nxp.com/docs/en/application-note/AN264.pdf
This is a simple model supporting the basic registers for led and GPIO
mode. The device also supports two blinking rates but not the model
yet.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180530064049.27976-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20180528232719.4721-17-f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since the macio device has a link to the PIC device, we can now wire up the
IRQs directly via qdev GPIOs rather than having to use an intermediate array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since the macio device has a link to the PIC device, we can now wire up the
IRQs directly via qdev GPIOs rather than having to use an intermediate array.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also switch macio_newworld_realize() over to use it rather than using the pic_mem
memory region directly.
Now that both Old World and New World macio devices no longer make use of the
pic_mem memory region directly, we can remove it.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Also switch macio_oldworld_realize() over to use it rather than using the pic_mem
memory region directly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add remaining easy registers to iotkit-secctl:
* NSCCFG just routes its two bits out to external GPIO lines
* BRGINSTAT/BRGINTCLR/BRGINTEN can be dummies, because QEMU's
bus fabric can never report errors
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180220180325.29818-18-peter.maydell@linaro.org
The IoTKit Security Controller includes various registers
that expose to software the controls for the Peripheral
Protection Controllers in the system. Implement these.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-17-peter.maydell@linaro.org
The Arm IoT Kit includes a "security controller" which is largely a
collection of registers for controlling the PPCs and other bits of
glue in the system. This commit provides the initial skeleton of the
device, implementing just the ID registers, and a couple of read-only
read-as-zero registers.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-16-peter.maydell@linaro.org
Add a model of the TrustZone peripheral protection controller (PPC),
which is used to gate transactions to non-TZ-aware peripherals so
that secure software can configure them to not be accessible to
non-secure software.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-15-peter.maydell@linaro.org
The MPS2 AN505 FPGA image includes a "FPGA control block"
which is a small set of registers handling LEDs, buttons
and some counters.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-14-peter.maydell@linaro.org
Move the definition of the struct for the unimplemented-device
from unimp.c to unimp.h, so that users can embed the struct
in their own device structs if they prefer.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-10-peter.maydell@linaro.org
RHEL6's compilers don't like the repeated typedef.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
The MOS6522 VIA forms the bridge part of several Mac devices, including the
Mac via-cuda and via-pmu devices. Introduce a standard mos6522 device that
can be shared amongst multiple implementations.
This is effectively taking the 6522 parts out of cuda.c and turning them
into a separate device whilst also applying some style tidy-ups and including
a conversion to trace-events.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Add minimal code needed to allow upstream Linux guest to boot.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add code to emulate SNVS IP-block. Currently only the bits needed to
be able to emulate machine shutdown are implemented.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add enough code to emulate i.MX2 watchdog IP block so it would be
possible to reboot the machine running Linux Guest.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add minimal code needed to allow upstream Linux guest to boot.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: Marcel Apfelbaum <marcel.apfelbaum@zoho.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ASPEED hardware contains a lock register for the SCU that disables
any writes to the SCU when it is locked. The machine comes up with the
lock enabled, but on all known hardware u-boot will unlock it and leave
it unlocked when loading the kernel.
This means the kernel expects the SCU to be unlocked. When booting from
an emulated ROM the normal u-boot unlock path is executed. Things don't
go well when booting using the -kernel command line, as u-boot does not
run first.
Change behaviour so that when a kernel is passed to the machine, set the
reset value of the SCU to be unlocked.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20171114122018.12204-1-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
See docs/specs/vmcoreinfo.txt for details.
"etc/vmcoreinfo" fw_cfg entry is added when using "-device vmcoreinfo".
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Added Sytem register block of Smartfusion2.
This block has PLL registers which are accessed by guest.
Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170920201737.25723-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement a model of the Serial Communication Controller (SCC) found
in MPS2 FPGA images.
The primary purpose of this device is to communicate with the
Motherboard Configuration Controller (MCC) which is located on
the MPS board itself, outside the FPGA image. This is used
for programming the MPS clock generators. The SCC also has
some basic ID registers and an output for the board LEDs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 1500029487-14822-7-git-send-email-peter.maydell@linaro.org
This introduces mmio_interface object which contains a MemoryRegion
and can be hotplugged/hotunplugged.
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Recent vanilla Raspberry Pi kernels started to make use of
the hardware random number generator in BCM2835 SoC. As a
result, those kernels wouldn't work anymore under QEMU
but rather just freeze during the boot process.
This patch implements a trivial BCM2835 compatible RNG,
and adds it as a peripheral to BCM2835 platform, which
allows to boot a vanilla Raspberry Pi kernel under Qemu.
Changes since v1:
* Prevented guest from writing [31..20] bits in rng_status
* Removed redundant minimum_version_id_old
* Added field entries for the state
* Changed realize function to reset
Signed-off-by: Marcin Chojnacki <marcinch7@gmail.com>
Message-id: 20170210210857.47893-1-marcinch7@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support moving the GCR base address & updating the CPU's CP0 CMGCRBase
register appropriately. This is required if a platform needs to move its
GCRs away from other memory, as the MIPS Boston development board does
to avoid its flash memory.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Create a new "unimplemented" sysbus device, which simply accepts
all read and write accesses, and implements them as read-as-zero,
write-ignored, with logging of the access as LOG_UNIMP.
This is useful for stubbing out bits of an SoC or board model
which haven't been written yet.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1484247815-15279-3-git-send-email-peter.maydell@linaro.org
There is not much differences with the A0 revision apart from the DDR
calibration.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1480434248-27138-10-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Configure the size of the RAM of the SOC using a property to propagate
the value down to the memory controller from the board level.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1473438177-26079-14-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is no need to do this at each reset as the RAM size will not
change.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1473438177-26079-12-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Based on previous work done by Andrew Jeffery <andrew@aj.id.au>.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-9-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This gives some explanation behind the magic number 0x120CE416.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-8-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The uboot in the previous release of the SDK was using a hardcoded
value for memory size. This is not true anymore, the value is now
retrieved from the memory controller.
Below is a model for this device, only supporting unlock and
configuration. Without it, we endup running a guest with 64MB, which
is a bit low nowdays. It uses a 'silicon-rev' property and ram_size to
build a default value. Some bits should be linked to SCU strapping
registers but it seems a bit complex to add for the current need.
The model is ready for the AST2500 SOC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AST2400_A0_SILICON_REV is defined twice. Fix this by including the
definition in the header file as well as the routine to check if a
silicon revision is supported. It will useful to reuse in other
controllers.
Let's add also AST2500_A0_SILICON_REV for future use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467994016-11678-5-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Header guard symbols should match their file name to make guard
collisions less likely. Offenders found with
scripts/clean-header-guards.pl -vn.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJXhMtOAAoJEFIRjjwLKdprahQH/2qBMp7Hnucy7jhiPHRtRZTo
zZAhuRJ0Z2LT9xH+sTg3HcjHI7aXps5cG2f7Fw4X/JKNRY4KO19yEBnMhc5he2Ut
XPtHCeMXXq6zU4RMHqlx6wChHn5AUll/3EeSvm6JMV+HhE6oDBk1yl5C8ipPlVCd
KEz6LlUFNMbuxu2tM4DoMNAWeKmunBx3vO+JuErB6hjCWM5G0mV9aPDkbwTOmVLn
qGgzzmNDiPE6JWrSpbHetsdCO7V9xtXzhcFsu240GJ/+XJMjUXb1m6ETsJxT9EYh
vLfFzwozBSjX6ZQZVNFIAeJZnq96NOHqZ56sU7s4YktVXjl26JAahScTTH0aiNo=
=sTce
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lalrae/tags/mips-20160712' into staging
MIPS patches 2016-07-12
Changes:
* support 10-bit ASIDs
* MIPS64R6-generic renamed to I6400
* initial GIC support
* implement RESET_BASE register in CM GCR
# gpg: Signature made Tue 12 Jul 2016 11:49:50 BST
# gpg: using RSA key 0x52118E3C0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
# Primary key fingerprint: 8DD3 2F98 5495 9D66 35D4 4FC0 5211 8E3C 0B29 DA6B
* remotes/lalrae/tags/mips-20160712:
target-mips: enable 10-bit ASIDs in I6400 CPU
target-mips: support CP0.Config4.AE bit
target-mips: change ASID type to hold more than 8 bits
target-mips: add ASID mask field and replace magic values
target-mips: replace MIPS64R6-generic with the real I6400 CPU model
hw/mips_cmgcr: implement RESET_BASE register in CM GCR
hw/mips_cpc: make VP correctly start from the reset vector
target-mips: add exception base to MIPS CPU
hw/mips/cps: create GIC block inside CPS
hw/mips: implement Global Interrupt Controller
hw/mips: implement GIC Interval Timer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement RESET_BASE register which is local to each VP and a write to
it changes VP's reset exception base. Also, add OTHER register to
allow a software running on one VP to access other VP's local registers.
Guest can use this mechanism to specify custom address from which a VP
will start execution.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
In various Freescale SOCs, the GPT timers can be configured to select
its input clock.
Depending on the SOC the set of available input clocks may vary.
The actual single GPT definition was no good enough and because of it
booting the sabrelite board with a i.MX6DL device tree would fail
because of an incorrect input clock definition for the i.MX6DL SOC.
This patch fixes the i.MX6DL boot failure by adding the ability to
define a different set of input clocks depending on the considered SOC.
A different class has been defined for i.MX25, i.MX31 and i.MX6 each with
its specific set of input clocks.
The patch has been tested by booting KZM, i.MX25 PDK, i.MX6Q sabrelite
and i.MX6DL sabrelite.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 1467325619-8374-1-git-send-email-jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed spacing round '/' operator]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On Windows 'aux.*' is a reserved name and cannot be used for
filenames; see
https://msdn.microsoft.com/en-gb/library/windows/desktop/aa365247(v=vs.85).aspx
This prevents cloning the QEMU git repo on Windows:
C:\Java\sources\kvm> git clone https://github.com/qemu/qemu.git
Cloning into 'qemu'...
remote: Counting objects: 279563, done.
remote: Total 279563 (delta 0), reused 0 (delta 0), pack-reused 279563R
Receiving objects: 100% (279563/279563), 122.45 MiB | 3.52 MiB/s, done.
Resolving deltas: 100% (221942/221942), done.
Checking connectivity... done.
error: unable to create file hw/misc/aux.c (No such file or directory)
error: unable to create file include/hw/misc/aux.h (No such file or directory)
Checking out files: 100% (4795/4795), done.
fatal: unable to checkout working tree
warning: Clone succeeded, but checkout failed.
You can inspect what was checked out with 'git status'
and retry the checkout with 'git checkout -f HEAD'
(bug https://bugs.launchpad.net/bugs/1595240)
Rename the offending files for the benefit of Windows.
Reported-by: Алексей Курган <akurgan@yandex.ru>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Wei Huang <wei@redhat.com>
Tested-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1467377145-32385-1-git-send-email-peter.maydell@linaro.org
The SCU is a collection of chip-level control registers that manage the
various functions supported by ASPEED SoCs. Typically the bits control
interactions with clocks, external hardware or reset behaviour, and we
can largly take a hands-off approach to reads and writes.
Firmware makes heavy use of the state to determine how to boot, but the
reset values vary from SoC to SoC (eg AST2400 vs AST2500). A qdev
property is exposed so that the integrating SoC model can configure the
silicon revision, which in-turn selects the appropriate reset values.
Further qdev properties are exposed so the board model can configure the
board-dependent hardware strapping.
Almost all provided AST2400 reset values are specified by the datasheet.
The notable exception is SOC_SCRATCH1, where we mark the DRAM as
successfully initialised to avoid unnecessary dark corners in the SoC's
u-boot support.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1466744305-23163-2-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: drop unnecessary inttypes.h include]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This introduces a new bus: aux-bus.
It contains an address space for aux slaves devices and a bridge to an I2C bus
for I2C through AUX transactions.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1465833014-21982-5-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This controller is also present in i.MX5X devices but they are not
yet emulated by QEMU.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Implement ITC as a single object consisting of two memory regions:
1) tag_io: ITC Configuration Tags (i.e. ITCAddressMap{0,1} registers) which
are accessible by the CPU via CACHE instruction. Also adding
MemoryRegion *itc_tag to the CPUMIPSState so that CACHE instruction will
dispatch reads/writes directly.
2) storage_io: memory-mapped ITC Storage whose address space is configurable
(i.e. enabled/remapped/resized) by writing to ITCAddressMap{0,1} registers.
ITC Storage contains FIFO and Semaphore cells. Read-only FIFO bit in the
ITC cell tag indicates the type of the cell. If the ITC Storage contains
both types of cells then FIFOs are located before Semaphores.
Since issuing thread can get blocked on the access to a cell (in E/F
Synchronized and P/V Synchronized Views) each cell has a bitmap to track
which threads are currently blocked.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Create Cluster Power Controller and add a link to the CPC MemoryRegion
in GCR. Guest can enable / map CPC to any physical address by writing to
the memory-mapped GCR_CPC_BASE register.
Set vp-start-reset property to 1 to allow only first VP to run from reset.
Others are brought up by the guest via CPC memory-mapped registers.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Cluster Power Controller (CPC) is responsible for power management in
multiprocessing system. It provides registers to control the power and the
clock frequency of the individual elements in the system.
This patch implements only three registers that are used to control the
power state of each VP on a single core:
* VP Run is a write-only register used to set each VP to the run state
* VP Stop is a write-only register used to set each VP to the suspend state
* VP Running is a read-only register indicating the run state of each VP
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add initial GCR support to indicate number of VPs present in the system,
L2 bypass mode and revision number.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
[leon.alrae@imgtec.com:
* removed GIC part,
* changed commit message,
* replaced %lx format spec. with PRIx64,
* renamed mips_gcr.{c,h} to mips_cmgcr.{c,h},
* replaced CONFIG_MIPS_GIC with CONFIG_MIPS_CPS]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
The property channel driver now interfaces with the framebuffer device
to query and set framebuffer parameters. As a result of this, the "get
ARM RAM size" query now correctly returns the video RAM base address
(not total RAM size), and the ram-size property is no longer relevant
here.
Signed-off-by: Grégory ESTRADE <gregory.estrade@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1457467526-8840-5-git-send-email-Andrew.Baumann@microsoft.com
[AB: cleanup/refactoring for upstream submission]
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
EPIT, GPT and other i.MX timers are using "abstract" clocks among which
a CLK_IPG_HIGH clock.
On i.MX25 and i.MX31 CLK_IPG and CLK_IPG_HIGH are mapped to the same clock
but on other SOC like i.MX6 they are mapped to distinct clocks.
This patch add the CLK_IPG_HIGH to prepare for SOC where these 2 clocks are
different.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 224bf650194760284cb40630e985867e1373276a.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Most clocks supported by the CCM are useless to the qemu framework.
Only clocks related to timers (EPIT, GPT, PWM, WATCHDOG, ...) are usefull
to QEMU code.
Therefore this patch removes clock computation handling for all clocks but:
* CLK_NONE,
* CLK_IPG,
* CLK_32k
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 9e7222efb349801032e60c0f6b0fbad0e5dcf648.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This way all CCM clock defines/enums are named CLK_XXX
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 8537df765c1713625c7a8b9aca4c7ca60b42e0c0.1456868959.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Return a valid value from the BCM2835 property mailbox query "get board
revision". This query is used by U-Boot. Implementing it fixes the first
obvious difference between qemu and real HW.
The value returned is currently hard-coded to match the RPi2 I own. Other
values are legal, e.g. different board manufacturer field values are
likely to exist in the wild.
Cc: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1454993910-24077-1-git-send-email-swarren@wwwdotorg.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This sits behind the mailbox interface, and implements
request/response queries for system properties. The
framebuffer-related properties will be added in a later patch.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the system mailboxes which are used to communicate with a
number of GPU peripherals on Pi/Pi2.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this i.MX25 and i.MX31 will have closer implementations.
Moreover all i.MX31 CCM registers are now present.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this CCM, i.MX25 timer is accurate with "real world time".
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 2c0cf90be767bfc8520661eca891ab22c61f18fe.1449528242.git.jcd@tribudubois.net
Reviewed-by Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The IMX_CCM class is now the base abstract class that is used by EPIT
and GPT timer implementation.
IMX31_CCM class is the concrete class implementing CCM for i.MX31 SOC.
For now the i.MX25 continues to use the i.MX31 CCM implementation.
An i.MX25 specific CCM will be introduced in a later patch.
We also rework initialization to stop using deprecated sysbus device init.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: fd3c7f87b50f5ebc99ec91f01413db35017f116d.1449528242.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is to prepare for CCM code refactoring.
This is just a bit of function and enum values renaming.
We also remove some useless intermediate variables.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 53c4d9b9611988a5f56f178f285e04490747925e.1449528242.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the Xilinx XADC core used in Zynq 7000.
References:
- Zynq-7000 All Programmable SoC Technical Reference Manual
- 7 Series FPGAs and Zynq-7000 All Programmable SoC XADC
Dual 12-Bit 1 MSPS Analog-to-Digital Converter
Tested with Linux using QEMU machine xilinx-zynq-a9 with devicetree
files zynq-zc702.dtb and zynq-zc706.dtb, and kernel configuration
multi_v7_defconfig.
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
[ PC changes:
* Changed macro names to match TRM where possible
* Made programmers model macro scheme consistent
* Dropped XADC_ZYNQ_ prefix on local macros
* Fix ALM field width
* Update threshold-comparison interrupts in _update_ints()
* factored out DFIFO pushes into helper. Renamed to "push/pop"
* Changed xadc_reg to 10 bits and added OOB check.
* Reduced scope of MCTL reset to just stop channel coms.
* Added dummy read data to write commands
* Changed _ to - seperators in string names and filenames
* Dropped ------------ in header comment
* Catchall'ed _update_ints() in _write handler.
* Minor whitespace changes.
* Use ZYNQ_XADC_FIFO_DEPTH instead of ARRAY_SIZE()
]
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Send a protocol version as the first message from server, clients must
close communication if they don't support this protocol version. Older
QEMUs should be fine with this change in the protocol since they
overrides their own vm_id on reception of an id associated to no
eventfd.
Signed-off-by: David Marchand <david.marchand@6wind.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
[use fifo_update_and_get()]
Reviewed-by: Claudio Fontana <claudio.fontana@huawei.com>
This patch adds the stm32f2xx System Configuration
Controller. This is used to configure what memory is mapped
at address 0 (although that is not supported) as well
as configure how the EXTI interrupts work (also not
supported at the moment).
This device is not required for basic examples, but more
complex systems will require it (as well as the EXTI device)
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 5d499d7b60b61d5d6dcb310b2e55411b1f53794e.1424175342.git.alistair@alistair23.me
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is done in preparation for the addition of VFIO platform
device support.
Signed-off-by: Kim Phillips <kim.phillips@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
While most operations with VFIO IOMMU driver are generic and used inside
vfio.c, there are still some operations which only specific VFIO IOMMU
drivers implement. The first example of it will be reading a DMA window
start from the host.
This adds a helper which passes an ioctl request to the container's fd.
The helper will check if @req is known. For this, stub is added. This return
-1 on any requests for now.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 9b8c69243 (since reverted) broke the ability to boot the kernel
as the value returned by unassigned_mem_read returned non-zero and left
the kernel looping forever waiting for it to change (see
integrator_led_set in the kernel code).
Relying on a varying implementation detail is incorrect anyway so this
introduces a basic stub of a memory region for the debug/LED section
on the integrator board.
Signed-off-by: Alex Bennée <alex@bennee.com>
Message-id: 1382451366-9539-1-git-send-email-alex.bennee@linaro.org
[PMM: removed three unused fields from struct IntegratorDebugState]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Many of these should be cleaned up with proper qdev-/QOM-ification.
Right now there are many catch-all headers in include/hw/ARCH depending
on cpu.h, and this makes it necessary to compile these files per-target.
However, fixing this does not belong in these patches.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Peter Maydell
Marc-André Lureau
Juan Quintela
Cédric Le Goater
Joel Stanley
Jean-Christophe Dubois
Paolo Bonzini
Andrew Jeffery
Mark Cave-Ayland
Philippe Mathieu-Daudé
Dr. David Alan Gilbert
Andrey Smirnov
Subbaraya Sundeep
KONRAD Frederic
Marcin Chojnacki
Paul Burton
Markus Armbruster
Leon Alrae
Yongbok Kim
Grégory ESTRADE
Stephen Warren
Andrew Baumann
Guenter Roeck
David Marchand
Alistair Francis
Kim Phillips
Alexey Kardashevskiy
Andreas Färber
Andreas Färber
Alex Bennée