The MacOS toolbox ROM accesses a number of addresses between 0x0 and 0x200 during
initialisation and resolution changes. Whilst the function of many of these
registers is unknown, it is worth the minimal cost of saving these extra values as
part of migration to help future-proof the migration stream for the q800 machine
as it starts to stabilise.
Note this is a migration break, but since there are upcoming incompatible changes
for the q800 machine (and migration does not even succeed without these patches)
then this is not an issue.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The current IRQ state and IRQ mask are handled exactly the same as standard
register accesses, so store these values directly in the regs array rather
than having separate variables for them.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305155530.9265-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that the logic related to edge-triggered interrupts is all contained within
the mos6522 device the redundant implementation for the mac99 PMU device can
be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
The mos6522 datasheet describes how the control lines IRQs are edge-triggered
according to the configuration in the PCR register. Implement the logic according
to the datasheet so that the interrupt bits in IFR are latched when the edge is
detected, and cleared when reading portA/portB or writing to IFR as necessary.
To maintain bisectibility this change also updates the SCSI, SCSI data, Nubus
and VIA2 60Hz/1Hz clocks in the q800 machine to be negative edge-triggered as
confirmed by the PCR programming in all of Linux, NetBSD and MacOS.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
To detect edge-triggered IRQs it is necessary to store the last state of each
IRQ in a last_irq_levels bitmap.
Note: this is a migration break for machines which use mos6522 instances which
are g3beige/mac99 (PPC) and q800 (m68k).
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This displays detailed information about the device registers and timers to aid
debugging problems with timers and interrupts.
Currently the QAPI generators for HumanReadableText don't work correctly if
used in qapi/target-misc.json when a non-specified target is built, so for
now manually add a hmp_info_via() wrapper until direct support for per-device
HMP/QMP commands is implemented.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This helps to follow how the guest is programming the mos6522 when debugging.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220305150957.5053-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Now that the mos6522 IRQs are managed using standard qdev gpios these methods
are no longer required.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
For historical reasons each mos6522 instance implements its own setting and
update of the IFR flag bits using methods exposed by MOS6522DeviceClass. As
of today this is no longer required, and it is now possible to implement
the mos6522 IRQs as standard qdev gpios.
Switch over to use qdev gpios for the mos6522 device and update all instances
accordingly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This allows us to easily see how the physical control lines are mapped to the
IFR bit flags.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220305150957.5053-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
This allows us to easily see how the physical control lines are mapped to the
IFR bit flags.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <20220305150957.5053-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
These are intended to make it easier to see how the physical control lines
are wired for each instance.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220305150957.5053-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
vhost-user enabled on non-linux systems
beginning of nvme sriov support
bigger tx queue for vdpa
virtio iommu bypass
FADT flag to detect legacy keyboards
Fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmImipMPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpD5AH/jz73VVDE3dZTtsdEH/f2tuO8uosur9fIjHJ
nCMwBoosdDWmrWjrwxynmG6e+qIcOHEGdTInvS1TY2OTU+elNNTiR57pWiljXRsJ
2kNIXKp4dXaYI/bxmKUzKSoVscyWxL686ND4U8sZhuppSNrWpLmMUNgwqmYjQQLV
yd2JpIKgZYnzShPnJMDtF3ItcCHetY6jeB28WAclKywIEuCTmjulYCTaH5ujroG9
rykMaQIjoe/isdmCcBx05UuMxH61vf5L8pR06N6e3GO9T2/Y/hWuteVoEJaCQvNa
+zIyL2hOjGuMKr+icLo9c42s3yfwWNsRfz87wqdAY47yYSyc1wo=
=3NVe
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio,pc,pci: features, cleanups, fixes
vhost-user enabled on non-linux systems
beginning of nvme sriov support
bigger tx queue for vdpa
virtio iommu bypass
FADT flag to detect legacy keyboards
Fixes, cleanups all over the place
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Mon 07 Mar 2022 22:43:31 GMT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (47 commits)
hw/acpi/microvm: turn on 8042 bit in FADT boot architecture flags if present
tests/acpi: i386: update FACP table differences
hw/acpi: add indication for i8042 in IA-PC boot flags of the FADT table
tests/acpi: i386: allow FACP acpi table changes
docs: vhost-user: add subsection for non-Linux platforms
configure, meson: allow enabling vhost-user on all POSIX systems
vhost: use wfd on functions setting vring call fd
event_notifier: add event_notifier_get_wfd()
pci: drop COMPAT_PROP_PCP for 2.0 machine types
hw/smbios: Add table 4 parameter, "processor-id"
x86: cleanup unused compat_apic_id_mode
vhost-vsock: detach the virqueue element in case of error
pc: add option to disable PS/2 mouse/keyboard
acpi: pcihp: pcie: set power on cap on parent slot
pci: expose TYPE_XIO3130_DOWNSTREAM name
pci: show id info when pci BDF conflict
hw/misc/pvpanic: Use standard headers instead
headers: Add pvpanic.h
pci-bridge/xio3130_downstream: Fix error handling
pci-bridge/xio3130_upstream: Fix error handling
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# docs/specs/index.rst
isa_init_irq() has become a trivial one-line wrapper for isa_get_irq().
It can therefore be removed.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com> (tpm_tis_isa)
Acked-by: Corey Minyard <cminyard@mvista.com> (isa_ipmi_bt, isa_ipmi_kcs)
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Message-Id: <20220301220037.76555-8-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220307134353.1950-14-philippe.mathieu.daude@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Now that the last users of ISADevice::isairq[] have been resolved during the
previous commits, it can be removed for good.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220301220037.76555-7-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220307134353.1950-13-philippe.mathieu.daude@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Exposing the IRQ number as a QOM property not only allows it to be
configurable but also to be displayed in HMP:
Before:
(qemu) info qtree
...
dev: mc146818rtc, id ""
gpio-out "" 1
base_year = 0 (0x0)
lost_tick_policy = "discard"
After:
dev: mc146818rtc, id ""
gpio-out "" 1
base_year = 0 (0x0)
irq = 8 (0x8)
lost_tick_policy = "discard"
The reason the IRQ number didn's show up before is that this device does not
call isa_init_irq().
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220301220037.76555-2-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220307134353.1950-9-philippe.mathieu.daude@gmail.com>
Reviewed-by: Bernhard Beschow <shentey@gmail.com>
Now that gt64120_register() lost its pic parameter, there is an
opportunity to remove it. gt64120_register() is old style by wrapping
qdev API, and the new style is to use qdev directly. So take the
opportunity and modernize the code.
Suggested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20220217101924.15347-8-shentey@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Now that piix4_set_irq's opaque parameter references own PIIX4State,
piix4_dev becomes redundant.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <20220217101924.15347-6-shentey@gmail.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Handling PCI interrupts in piix4 increases cohesion and reduces differences
between piix4 and piix3.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220217101924.15347-3-shentey@gmail.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
The Renesas RAA229004 is a PMBus Multiphase Voltage Regulator
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-9-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
- add the VOUT_MIN and STATUS_MFR registers
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-2-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
* cleanups of qemu_oom_check() and qemu_memalign()
* target/arm/translate-neon: UNDEF if VLD1/VST1 stride bits are non-zero
* target/arm/translate-neon: Simplify align field check for VLD3
* GICv3 ITS: add more trace events
* GICv3 ITS: implement 8-byte accesses properly
* GICv3: fix minor issues with some trace/log messages
* ui/cocoa: Use the standard about panel
* target/arm: Provide cpu property for controling FEAT_LPA2
* hw/arm/virt: Disable LPA2 for -machine virt-6.2
-----BEGIN PGP SIGNATURE-----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=ix0J
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20220307' into staging
target-arm queue:
* cleanups of qemu_oom_check() and qemu_memalign()
* target/arm/translate-neon: UNDEF if VLD1/VST1 stride bits are non-zero
* target/arm/translate-neon: Simplify align field check for VLD3
* GICv3 ITS: add more trace events
* GICv3 ITS: implement 8-byte accesses properly
* GICv3: fix minor issues with some trace/log messages
* ui/cocoa: Use the standard about panel
* target/arm: Provide cpu property for controling FEAT_LPA2
* hw/arm/virt: Disable LPA2 for -machine virt-6.2
# gpg: Signature made Mon 07 Mar 2022 16:46:06 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20220307:
hw/arm/virt: Disable LPA2 for -machine virt-6.2
target/arm: Provide cpu property for controling FEAT_LPA2
ui/cocoa: Use the standard about panel
hw/intc/arm_gicv3_cpuif: Fix register names in ICV_HPPIR read trace event
hw/intc/arm_gicv3: Fix missing spaces in error log messages
hw/intc/arm_gicv3: Specify valid and impl in MemoryRegionOps
hw/intc/arm_gicv3_its: Add trace events for table reads and writes
hw/intc/arm_gicv3_its: Add trace events for commands
target/arm/translate-neon: Simplify align field check for VLD3
target/arm/translate-neon: UNDEF if VLD1/VST1 stride bits are non-zero
osdep: Move memalign-related functions to their own header
util: Put qemu_vfree() in memalign.c
util: Use meson checks for valloc() and memalign() presence
util: Share qemu_try_memalign() implementation between POSIX and Windows
meson.build: Don't misdetect posix_memalign() on Windows
util: Return valid allocation for qemu_try_memalign() with zero size
util: Unify implementations of qemu_memalign()
util: Make qemu_oom_check() a static function
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The naming makes more sense in a SPI controller model.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220307071856.1410731-5-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
It is not used anymore.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220307071856.1410731-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
In
commit a71d597b98
Author: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Date: Thu Jun 10 13:08:00 2021 +0300
block/nbd: reuse nbd_co_do_establish_connection() in nbd_open()
the use of the 'hostname' field from the BDRVNBDState struct was
lost, and 'nbd_connect' just hardcoded it to match the IP socket
address. This was a harmless bug at the time since we block use
with anything other than IP sockets.
Shortly though, we want to allow the caller to override the hostname
used in the TLS certificate checks. This is to allow for TLS
when doing port forwarding or tunneling. Thus we need to reinstate
the passing along of the 'hostname'.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-Id: <20220304193610.3293146-3-berrange@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
- Use CPUArchState as an abstract type, defined by each target
(CPUState is our interface with generic code, CPUArchState is
our interface with target-specific code).
-----BEGIN PGP SIGNATURE-----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=bOxK
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/philmd/tags/abstract-arch-cpu-20220307' into staging
- Re-org accel/ and softmmu/ to have more target-agnostic objects.
- Use CPUArchState as an abstract type, defined by each target
(CPUState is our interface with generic code, CPUArchState is
our interface with target-specific code).
# gpg: Signature made Sun 06 Mar 2022 23:23:19 GMT
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd/tags/abstract-arch-cpu-20220307: (33 commits)
accel/tcg: Remove pointless CPUArchState casts
target/i386: Remove pointless CPUArchState casts
target: Use ArchCPU as interface to target CPU
target: Introduce and use OBJECT_DECLARE_CPU_TYPE() macro
target: Use CPUArchState as interface to target-specific CPU state
target: Use forward declared type instead of structure type
target/hexagon: Add missing 'hw/core/cpu.h' include
target: Include missing 'cpu.h'
Hexagon (target/hexagon) convert to OBJECT_DECLARE_TYPE
target/i386/tcg/sysemu: Include missing 'exec/exec-all.h' header
cpu: Add missing 'exec/exec-all.h' and 'qemu/accel.h' headers
exec/cpu_ldst: Include 'cpu.h' to get target_ulong definition
meson: Display libfdt as disabled when system emulation is disabled
softmmu: Build target-agnostic objects once
softmmu: Add qemu_init_arch_modules()
exec/cpu: Make address_space_init/reloading_memory_map target agnostic
exec/gdbstub: Make gdb_exit() / gdb_set_stop_cpu() target agnostic
misc: Add missing "sysemu/cpu-timers.h" include
misc: Remove unnecessary "sysemu/cpu-timers.h" include
softmmu/cpu-timers: Remove unused 'exec/exec-all.h' header
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a Linux kernel bug present until v5.12 that prevents
booting with FEAT_LPA2 enabled. As a workaround for TCG,
disable this feature for machine versions prior to 7.0.
Cc: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Move the various memalign-related functions out of osdep.h and into
their own header, which we include only where they are used.
While we're doing this, add some brief documentation comments.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220226180723.1706285-10-peter.maydell@linaro.org
The qemu_oom_check() function, which we define in both oslib-posix.c
and oslib-win32.c, is now used only locally in that file; make it
static.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220226180723.1706285-3-peter.maydell@linaro.org
Function qemu_dirent_dup() is currently only used by 9pfs server, so move
it from project global header osdep.h to 9pfs specific header 9p-util.h.
Link: https://lore.kernel.org/qemu-devel/CAFEAcA_=HAUNomKD2wurSVaAHa5mrk22A1oHKLWUDjk7v6Khmg@mail.gmail.com/
Based-on: <20220227223522.91937-12-wwcohen@gmail.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <E1nP9Oz-00043L-KJ@lizzy.crudebyte.com>
- Guard Linux only headers.
- Add qemu/statfs.h header to abstract over the which
headers are needed for struct statfs
- Define `ENOATTR` only if not only defined
(it's defined in system headers on Darwin).
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
[Michael Roitzsch: - Rebase for NixOS]
Signed-off-by: Michael Roitzsch <reactorcontrol@icloud.com>
While it might at first appear that fsdev/virtfs-proxy-header.c would
need similar adjustment for darwin as file-op-9p here, a later patch in
this series disables virtfs-proxy-helper for non-Linux. Allowing
virtfs-proxy-helper on darwin could potentially be an additional
optimization later.
[Will Cohen: - Fix headers for Alpine
- Integrate statfs.h back into file-op-9p.h
- Remove superfluous header guards from file-opt-9p
- Add note about virtfs-proxy-helper being disabled
on non-Linux for this patch series]
Signed-off-by: Will Cohen <wwcohen@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20220227223522.91937-2-wwcohen@gmail.com>
Signed-off-by: Christian Schoenebeck <qemu_oss@crudebyte.com>
The new block driver simply utilizes snapshot-access API of underlying
block node.
In further patches we want to use it like this:
[guest] [NBD export]
| |
| root | root
v file v
[copy-before-write]<------[snapshot-access]
| |
| file | target
v v
[active-disk] [temp.img]
This way, NBD client will be able to read snapshotted state of active
disk, when active disk is continued to be written by guest. This is
known as "fleecing", and currently uses another scheme based on qcow2
temporary image which backing file is active-disk. New scheme comes
with benefits - see next commit.
The other possible application is exporting internal snapshots of
qcow2, like this:
[guest] [NBD export]
| |
| root | root
v file v
[qcow2]<---------[snapshot-access]
For this, we'll need to implement snapshot-access API handlers in
qcow2 driver, and improve snapshot-access block driver (and API) to
make it possible to select snapshot by name. Another thing to improve
is size of snapshot. Now for simplicity we just use size of bs->file,
which is OK for backup, but for qcow2 snapshots export we'll need to
imporve snapshot-access API to get size of snapshot.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Message-Id: <20220303194349.2304213-12-vsementsov@virtuozzo.com>
[hreitz: Rebased on block GS/IO split]
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Add new block driver handlers and corresponding generic wrappers.
It will be used to allow copy-before-write filter to provide
reach fleecing interface in further commit.
In future this approach may be used to allow reading qcow2 internal
snapshots, for example to export them through NBD.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220303194349.2304213-11-vsementsov@virtuozzo.com>
[hreitz: Rebased on block GS/IO split]
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Add function to wait for all intersecting requests.
To be used in the further commit.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Nikita Lapshin <nikita.lapshin@virtuozzo.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220303194349.2304213-10-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Add a convenient function similar with bdrv_block_status() to get
status of dirty bitmap.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220303194349.2304213-9-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Split intersecting-requests functionality out of block-copy to be
reused in copy-before-write filter.
Note: while being here, fix tiny typo in MAINTAINERS.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220303194349.2304213-7-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Split block_copy_reset() out of block_copy_reset_unallocated() to be
used separately later.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220303194349.2304213-6-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
This will be used in the following commit to bring "incremental" mode
to copy-before-write filter.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220303194349.2304213-4-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
That simplifies handling failure in existing code and in further new
usage of bdrv_merge_dirty_bitmap().
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220303194349.2304213-3-vsementsov@virtuozzo.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
There is a bug in handling BDRV_REQ_NO_WAIT flag: we still may wait in
wait_serialising_requests() if request is unaligned. And this is
possible for the only user of this flag (preallocate filter) if
underlying file is unaligned to its request_alignment on start.
So, we have to fix preallocate filter to do only aligned preallocate
requests.
Next, we should fix generic block/io.c somehow. Keeping in mind that
preallocate is the only user of BDRV_REQ_NO_WAIT and that we have to
fix its behavior now, it seems more safe to just assert that we never
use BDRV_REQ_NO_WAIT with unaligned requests and add corresponding
comment. Let's do so.
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Denis V. Lunev <den@openvz.org>
Message-Id: <20220215121609.38570-1-vsementsov@virtuozzo.com>
[hreitz: Rebased on block GS/IO split]
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
ArchCPU is our interface with target-specific code. Use it as
a forward-declared opaque pointer (abstract type), having its
structure defined by each target.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-15-f4bug@amsat.org>
Replace the boilerplate code to declare CPU QOM types
and macros, and forward-declare the CPU instance type.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-14-f4bug@amsat.org>
While CPUState is our interface with generic code, CPUArchState is
our interface with target-specific code. Use CPUArchState as an
abstract type, defined by each target.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-13-f4bug@amsat.org>
This can allow the guest OS to determine more easily if i8042 controller
is present in the system or not, so it doesn't need to do probing of the
controller, but just initialize it immediately, before enumerating the
ACPI AML namespace.
The 8042 bit in IAPC_BOOT_ARCH was introduced from ACPI spec v2 (FADT
revision 2 and above). Therefore, in this change, we only enable this bit for
x86/q35 machine types since x86/i440fx machines use FADT ACPI table with
revision 1.
Signed-off-by: Liav Albani <liavalb@gmail.com>
Signed-off-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <20220304154032.2071585-3-ani@anisinha.ca>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-5-f4bug@amsat.org>
module_allow_arch() is the single target-specific call in the
whole vl.c file. Move the module initialization out to arch_init.c,
that way we'll be able to build vl.o once for all targets (the
next commit).
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-21-f4bug@amsat.org>
cpu_address_space_init() and cpu_reloading_memory_map() are
target-agnostic, but are declared in "exec/exec-all.h" which
contains target-specific declarations. Any target-agnostic
source including "exec/exec-all.h" becomes target-specific and
we have to compile it N times for the N targets built. In order
to avoid that, move the declarations to "exec/cpu-common.h" which
only contains target-agnostic declarations.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-20-f4bug@amsat.org>
gdb_exit() and gdb_set_stop_cpu() prototypes don't have to be
target specific. Remove this limitation to be able to build
softmmu/cpus.c and softmmu/runstate.c once for all targets.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-19-f4bug@amsat.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-18-f4bug@amsat.org>
Add cpus_are_resettable() to AccelOps, and implement it for the
KVM accelerator.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-12-f4bug@amsat.org>
Add cpu_thread_is_idle() to AccelOps, and implement it for the
KVM / WHPX accelerators.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-11-f4bug@amsat.org>
Mirror "sysemu/kvm.h" #ifdef'ry to define CONFIG_HAX_IS_POSSIBLE,
expose hax_allowed to hax_enabled() macro.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-9-f4bug@amsat.org>
kvm_on_sigbus() and kvm_on_sigbus_vcpu() prototypes don't have
to be target specific. Remove this limitation to be able to build
softmmu/cpus.c once for all targets.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-7-f4bug@amsat.org>
target_ulong is target-specific, while vaddr isn't.
Remove the unnecessary "exec/cpu-defs.h" target-speficic header
from "memory_mapping.h" and use the target-agnostic "hw/core/cpu.h"
locally in memory_mapping.c.
Remove "exec/memory.h" since MemoryRegion is forward-declared in
"qemu/typedefs.h".
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-6-f4bug@amsat.org>
cpu_memory_rw_debug() is declared in "exec/cpu-all.h" which
contains target-specific declarations. To be able to use it
from target agnostic source, move the declaration to the
generic "exec/cpu-common.h" header.
Replace the target-specific 'target_ulong' type by 'vaddr'
which better reflects the argument type, and is target agnostic.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-5-f4bug@amsat.org>
Move vaddr type declaration to the generic "exec/cpu-common.h" header.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220207075426.81934-4-f4bug@amsat.org>
event_notifier_get_fd(const EventNotifier *e) always returns
EventNotifier's read file descriptor (rfd). This is not a problem when
the EventNotifier is backed by a an eventfd, as a single file
descriptor is used both for reading and triggering events (rfd ==
wfd).
But, when EventNotifier is backed by a pipe pair, we have two file
descriptors, one that can only be used for reads (rfd), and the other
only for writes (wfd).
There's, at least, one known situation in which we need to obtain wfd
instead of rfd, which is when setting up the file that's going to be
sent to the peer in vhost's SET_VRING_CALL.
Add a new event_notifier_get_wfd(const EventNotifier *e) that can be
used to obtain wfd where needed.
Signed-off-by: Sergio Lopez <slp@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220304100854.14829-2-slp@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
commit
f862ddbb1a (hw/i386: Remove the deprecated pc-1.x machine types)
removed the last user of broken APIC ID compat knob,
but compat_apic_id_mode itself was forgotten.
Clean it up and simplify x86_cpu_apic_id_from_index()
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20220228131634.3389805-1-imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
On some older software like Windows 7 installer, having both a PS/2
mouse and USB mouse results in only one device working property (which
might be a different device each boot). While the workaround to not use
a USB mouse with such software is valid, it creates an inconsistent
experience if the user wishes to always use a USB mouse.
This introduces a new machine property to inhibit the creation of the
i8042 PS/2 controller.
Signed-off-by: Joelle van Dyne <j@getutm.app>
Message-Id: <20220227210655.45592-1-j@getutm.app>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
on creation a PCIDevice has power turned on at the end of pci_qdev_realize()
however later on if PCIe slot isn't populated with any children
it's power is turned off. It's fine if native hotplug is used
as plug callback will power slot on among other things.
However when ACPI hotplug is enabled it replaces native PCIe plug
callbacks with ACPI specific ones (acpi_pcihp_device_*plug_cb) and
as result slot stays powered off. It works fine as ACPI hotplug
on guest side takes care of enumerating/initializing hotplugged
device. But when later guest is migrated, call chain introduced by]
commit d5daff7d31 (pcie: implement slot power control for pcie root ports)
pcie_cap_slot_post_load()
-> pcie_cap_update_power()
-> pcie_set_power_device()
-> pci_set_power()
-> pci_update_mappings()
will disable earlier initialized BARs for the hotplugged device
in powered off slot due to commit 23786d1344 (pci: implement power state)
which disables BARs if power is off.
Fix it by setting PCI_EXP_SLTCTL_PCC to PCI_EXP_SLTCTL_PWR_ON
on slot (root port/downstream port) at the time a device
hotplugged into it. As result PCI_EXP_SLTCTL_PWR_ON is migrated
to target and above call chain keeps device plugged into it
powered on.
Fixes: d5daff7d31 ("pcie: implement slot power control for pcie root ports")
Fixes: 23786d1344 ("pci: implement power state")
Fixes: https://bugzilla.redhat.com/show_bug.cgi?id=2053584
Suggested-by: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20220301151200.3507298-3-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Type name will be used in followup patch for cast check
in pcihp code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20220301151200.3507298-2-imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
QEMU side has already imported pvpanic.h from linux, remove bit
definitions from include/hw/misc/pvpanic.h, and use
include/standard-headers/linux/pvpanic.h instead.
Also minor changes for PVPANIC_CRASHLOADED -> PVPANIC_CRASH_LOADED.
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20220221122717.1371010-2-pizhenwei@bytedance.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Since 2020, linux kernel started to export pvpanic.h. Import the
latest version from linux into QEMU.
Signed-off-by: zhenwei pi <pizhenwei@bytedance.com>
Message-Id: <20220221122717.1371010-1-pizhenwei@bytedance.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Łukasz Gieryk <lukasz.gieryk@linux.intel.com>
Message-Id: <20220217174504.1051716-5-lukasz.maniak@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Convenience function for retrieving the PCIDevice object of the N-th VF.
Signed-off-by: Łukasz Gieryk <lukasz.gieryk@linux.intel.com>
Reviewed-by: Knut Omang <knuto@ifi.uio.no>
Message-Id: <20220217174504.1051716-4-lukasz.maniak@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This patch provides the building blocks for creating an SR/IOV
PCIe Extended Capability header and register/unregister
SR/IOV Virtual Functions.
Signed-off-by: Knut Omang <knuto@ifi.uio.no>
Message-Id: <20220217174504.1051716-2-lukasz.maniak@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Currently the virtio-iommu device must be programmed before it allows
DMA from any PCI device. This can make the VM entirely unusable when a
virtio-iommu driver isn't present, for example in a bootloader that
loads the OS from storage.
Similarly to the other vIOMMU implementations, default to DMA bypassing
the IOMMU during boot. Add a "boot-bypass" property, defaulting to true,
that lets users change this behavior.
Replace the VIRTIO_IOMMU_F_BYPASS feature, which didn't support bypass
before feature negotiation, with VIRTIO_IOMMU_F_BYPASS_CONFIG.
We add the bypass field to the migration stream without introducing
subsections, based on the assumption that this virtio-iommu device isn't
being used in production enough to require cross-version migration at
the moment (all previous version required workarounds since they didn't
support ACPI and boot-bypass).
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-Id: <20220214124356.872985-3-jean-philippe@linaro.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
SC is required for some kernel features like vhost-vDPA. So this patch
implements basic SC feature. The idea is pretty simple, for software
emulated DMA it would be always coherent. In this case we can simple
advertise ECAP_SC bit. For VFIO and vhost, thing will be more much
complicated, so this patch simply fail the IOMMU notifier
registration.
In the future, we may want to have a dedicated notifiers flag or
similar mechanism to demonstrate the coherency so VFIO could advertise
that if it has VFIO_DMA_CC_IOMMU, for vhost kernel backend we don't
need that since it's a software backend.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220214060346.72455-1-jasowang@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
There are some operation sizes in some subsets of AVX512 that
are missing from previous iterations of AVX. Detect them.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
We've had placeholders for these opcodes for a while,
and should have support on ppc, s390x and avx512 hosts.
Tested-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The last entry of DEF_HELPERS_FLAGS_n is DEF_HELPER_FLAGS_7 and
thus the MAX_OPC_PARAM_IARGS should be 7.
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Signed-off-by: Ziqiao Kong <ziqiaokong@gmail.com>
Message-Id: <20220227113127.414533-2-ziqiaokong@gmail.com>
Fixes: e6cadf49c3 ("tcg: Add support for a helper with 7 arguments")
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The job API will be handled separately in another serie.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-31-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Assertions in the callers of the function pointrs are already
added by previous patches.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20220303151616.325444-30-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-28-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Similar to the header split, also the function pointers in BlockDriver
can be split in I/O and global state.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-26-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Snapshots run also under the BQL, so they all are
in the global state API. The aiocontext lock that they hold
is currently an overkill and in future could be removed.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-23-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
blockdev functions run always under the BQL lock.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-21-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
blockjob functions run always under the BQL lock.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-19-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Since the I/O functions are not many, keep a single file.
Also split the function pointers in BlockJobDriver.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220303151616.325444-16-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
We want to be sure that the functions that write the child and
parent list of a bs are under BQL and drain.
BQL prevents from concurrent writings from the GS API, while
drains protect from I/O.
TODO: drains are missing in some functions using this assert.
Therefore a proper assertion will fail. Because adding drains
requires additional discussions, they will be added in future
series.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-15-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Mark all I/O functions with IO_CODE, and all "I/O OR GS" with
IO_OR_GS_CODE.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-14-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Similarly to the previous patch, split block_int.h
in block_int-io.h and block_int-global-state.h
block_int-common.h contains the structures shared between
the two headers, and the functions that can't be categorized as
I/O or global state.
Assertions are added in the next patch.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-12-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Mark all I/O functions with IO_CODE, and all "I/O OR GS" with
IO_OR_GS_CODE.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-10-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Similarly to the previous patches, split block-backend.h
in block-backend-io.h and block-backend-global-state.h
In addition, remove "block/block.h" include as it seems
it is not necessary anymore, together with "qemu/iov.h"
block-backend-common.h contains the structures shared between
the two headers, and the functions that can't be categorized as
I/O or global state.
Assertions are added in the next patch.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-8-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Mark all I/O functions with IO_CODE, and all "I/O OR GS" with
IO_OR_GS_CODE.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-6-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
block.h currently contains a mix of functions:
some of them run under the BQL and modify the block layer graph,
others are instead thread-safe and perform I/O in iothreads.
Some others can only be called by either the main loop or the
iothread running the AioContext (and not other iothreads),
and using them in another thread would cause deadlocks, and therefore
it is not ideal to define them as I/O.
It is not easy to understand which function is part of which
group (I/O vs GS vs "I/O or GS"), and this patch aims to clarify it.
The "GS" functions need the BQL, and often use
aio_context_acquire/release and/or drain to be sure they
can modify the graph safely.
The I/O function are instead thread safe, and can run in
any AioContext.
"I/O or GS" functions run instead in the main loop or in
a single iothread, and use BDRV_POLL_WHILE().
By splitting the header in two files, block-io.h
and block-global-state.h we have a clearer view on what
needs what kind of protection. block-common.h
contains common structures shared by both headers.
block.h is left there for legacy and to avoid changing
all includes in all c files that use the block APIs.
Assertions are added in the next patch.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-4-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Righ now, IO_CODE and IO_OR_GS_CODE are nop, as there isn't
really a way to check that a function is only called in I/O.
On the other side, we can use qemu_in_main_thread() to check if
we are in the main loop.
The usage of macros makes easy to extend them in the future without
making changes in all callers. They will also visually help understanding
in which category each function is, without looking at the header.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-3-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
When invoked from the main loop, this function is the same
as qemu_mutex_iothread_locked, and returns true if the BQL is held.
When invoked from iothreads or tests, it returns true only
if the current AioContext is the Main Loop.
This essentially just extends qemu_mutex_iothread_locked to work
also in unit tests or other users like storage-daemon, that run
in the Main Loop but end up using the implementation in
stubs/iothread-lock.c.
Using qemu_mutex_iothread_locked in unit tests defaults to false
because they use the implementation in stubs/iothread-lock,
making all assertions added in next patches fail despite the
AioContext is still the main loop.
See the comment in the function header for more information.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220303151616.325444-2-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The daemonizing functions in os-posix (os_daemonize() and
os_setup_post()) only daemonize the process if the static `daemonize`
variable is set. Right now, it can only be set by os_parse_cmd_args().
In order to use os_daemonize() and os_setup_post() from the storage
daemon to have it be daemonized, we need some other way to set this
`daemonize` variable, because I would rather not tap into the system
emulator's arg-parsing code. Therefore, this patch adds an
os_set_daemonize() function, which will return an error on os-win32
(because daemonizing is not supported there).
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220303164814.284974-2-hreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
RCU may be used from coroutines. Standard __thread variables cannot be
used by coroutines. Use the coroutine TLS macros instead.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220222140150.27240-4-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Compiler optimizations can cache TLS values across coroutine yield
points, resulting in stale values from the previous thread when a
coroutine is re-entered by a new thread.
Serge Guelton developed an __attribute__((noinline)) wrapper and tested
it with clang and gcc. I formatted his idea according to QEMU's coding
style and wrote documentation.
The compiler can still optimize based on analyzing noinline code, so an
asm volatile barrier with an output constraint is required to prevent
unwanted optimizations.
Buglink: https://bugzilla.redhat.com/show_bug.cgi?id=1952483
Suggested-by: Serge Guelton <sguelton@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220222140150.27240-2-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Following the bdrv_activate renaming, change also the name
of the respective callers.
bdrv_invalidate_cache_all -> bdrv_activate_all
blk_invalidate_cache -> blk_activate
test_sync_op_invalidate_cache -> test_sync_op_activate
No functional change intended.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220209105452.1694545-5-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
This function is currently just a wrapper for bdrv_invalidate_cache(),
but in future will contain the code of bdrv_co_invalidate_cache() that
has to always be protected by BQL, and leave the rest in the I/O
coroutine.
Replace all bdrv_invalidate_cache() invokations with bdrv_activate().
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Reviewed-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220209105452.1694545-4-eesposit@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Move the permission API calls into driver-specific callbacks
that always run under BQL. In this case, bdrv_crypto_luks
needs to perform permission checks before and after
qcrypto_block_amend_options(). The problem is that the caller,
block_crypto_amend_options_generic_luks(), can also run in I/O
from .bdrv_co_amend(). This does not comply with Global State-I/O API split,
as permissions API must always run under BQL.
Firstly, introduce .bdrv_amend_pre_run() and .bdrv_amend_clean()
callbacks. These two callbacks are guaranteed to be invoked under
BQL, respectively before and after .bdrv_co_amend().
They take care of performing the permission checks
in the same way as they are currently done before and after
qcrypto_block_amend_options().
These callbacks are in preparation for next patch, where we
delete the original permission check. Right now they just add redundant
control.
Then, call .bdrv_amend_pre_run() before job_start in
qmp_x_blockdev_amend(), so that it will be run before the job coroutine
is created and stay in the main loop.
As a cleanup, use JobDriver's .clean() callback to call
.bdrv_amend_clean(), and run amend-specific cleanup callbacks under BQL.
After this patch, permission failures occur early in the blockdev-amend
job to update a LUKS volume's keys. iotest 296 must now expect them in
x-blockdev-amend's QMP reply instead of waiting for the actual job to
fail later.
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220209105452.1694545-2-eesposit@redhat.com>
Signed-off-by: Hanna Reitz <hreitz@redhat.com>
Message-Id: <20220304153729.711387-6-hreitz@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
VIRTIO_I2C_F_ZERO_LENGTH_REQUEST is a mandatory feature, that must be
implemented by everyone. Add its support.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Message-Id: <fc47ab63b1cd414319c9201e8d6c7705b5ec3bd9.1644490993.git.viresh.kumar@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
When vhost-user device cleanup, remove notifier MR and munmaps notifier
address in the event-handling thread, VM CPU thread writing the notifier
in concurrent fails with an error of accessing invalid address. It
happens because MR is still being referenced and accessed in another
thread while the underlying notifier mmap address is being freed and
becomes invalid.
This patch calls RCU and munmap notifiers in the callback after the
memory flatview update finish.
Fixes: 44866521bd ("vhost-user: support registering external host notifiers")
Cc: qemu-stable@nongnu.org
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Message-Id: <20220207071929.527149-3-xuemingl@nvidia.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Notifier set when vhost-user backend asks qemu to mmap an FD and
offset. When vhost-user backend restart or getting killed, VQ notifier
FD and mmap addresses become invalid. After backend restart, MR contains
the invalid address will be restored and fail on notifier access.
On the other hand, qemu should munmap the notifier, release underlying
hardware resources to enable backend restart and allocate hardware
notifier resources correctly.
Qemu shouldn't reference and use resources of disconnected backend.
This patch removes VQ notifier restore, uses the default vhost-user
notifier to avoid invalid address access.
After backend restart, the backend should ask qemu to install a hardware
notifier if needed.
Fixes: 44866521bd ("vhost-user: support registering external host notifiers")
Cc: qemu-stable@nongnu.org
Signed-off-by: Xueming Li <xuemingl@nvidia.com>
Message-Id: <20220207071929.527149-2-xuemingl@nvidia.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* Fixup checks for ext_zb[abcs]
* Add AIA support for virt machine
* Increase maximum number of CPUs in virt machine
* Fixup OpenTitan SPI address
* Add support for zfinx, zdinx and zhinx{min} extensions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAmIgUZ8ACgkQIeENKd+X
cFTzegf8DbUYFLpyfURm6bJoJfLQHjtjB4Hs6PnszJZZAEtC6Ia+551TDjh93vTf
GTbpWm0BlugQqEeyg+Mioe2mb2EhK2w208RGXRSDjT9QFVOaIp83NDAjaQTPqs22
XC35ygJYuo1Yf0WoJV77aB6IYPZB3ba5i+dkGb6lk60Ru5ULqoLvqp73tNe5KvNB
uVAEy+ubzjmzWs5hGPw95HqTIbcMGnlHew4XU6xJaiJixSy71Z5nOCCn+2sxk+6A
QW59Onglyfk01F9ac3GMLvi2e+FUdj0S0y07oVqchzxXWYpYwgTO4Xkt794c8mqU
T02kuelfubr1qH1z/IolStju1JnaXw==
=LzOY
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20220303' into staging
Fifth RISC-V PR for QEMU 7.0
* Fixup checks for ext_zb[abcs]
* Add AIA support for virt machine
* Increase maximum number of CPUs in virt machine
* Fixup OpenTitan SPI address
* Add support for zfinx, zdinx and zhinx{min} extensions
# gpg: Signature made Thu 03 Mar 2022 05:26:55 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20220303:
target/riscv: expose zfinx, zdinx, zhinx{min} properties
target/riscv: add support for zhinx/zhinxmin
target/riscv: add support for zdinx
target/riscv: add support for zfinx
target/riscv: hardwire mstatus.FS to zero when enable zfinx
target/riscv: add cfg properties for zfinx, zdinx and zhinx{min}
hw: riscv: opentitan: fixup SPI addresses
hw/riscv: virt: Increase maximum number of allowed CPUs
docs/system: riscv: Document AIA options for virt machine
hw/riscv: virt: Add optional AIA IMSIC support to virt machine
hw/intc: Add RISC-V AIA IMSIC device emulation
hw/riscv: virt: Add optional AIA APLIC support to virt machine
target/riscv: fix inverted checks for ext_zb[abcs]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds support for one possible new protection information format
introduced in TP4068 (and integrated in NVMe 2.0): the 64-bit CRC guard
and 48-bit reference tag. This version does not support storage tags.
Like the CRC16 support already present, this uses a software
implementation of CRC64 (so it is naturally pretty slow). But its good
enough for verification purposes.
This may go nicely hand-in-hand with the support that Keith submitted
for the Linux kernel[1].
[1]: https://lore.kernel.org/linux-nvme/20220126165214.GA1782352@dhcp-10-100-145-180.wdc.com/T/
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Naveen Nagar <naveen.n1@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for up to 64 LBA formats through the LBAFEE field of the
Host Behavior Support feature.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Naveen Nagar <naveen.n1@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add support for getting and setting the Host Behavior Support feature.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Naveen Nagar <naveen.n1@samsung.com>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
This patch updates the SPI_DEVICE, SPI_HOST0, SPI_HOST1
base addresses. Also adds these as unimplemented devices.
The address references can be found [1].
[1] 6c317992fb/hw/top_earlgrey/sw/autogen/top_earlgrey_memory.h (L107)
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220218063839.405082-1-alistair.francis@opensource.wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
To facilitate software development of RISC-V systems with large number
of HARTs, we increase the maximum number of allowed CPUs to 512 (2^9).
We also add a detailed source level comments about limit defines which
impact the physical address space utilization.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-Id: <20220220085526.808674-6-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate both AIA IMSIC and AIA APLIC
devices only when "aia=aplic-imsic" parameter is passed along
with machine name in the QEMU command-line. The AIA IMSIC is
only a per-HART MSI controller so we use AIA APLIC in MSI-mode
to forward all wired interrupts as MSIs to the AIA IMSIC.
We also provide "aia-guests=<xyz>" parameter which can be used
to specify number of VS-level AIA IMSIC Guests MMIO pages for
each HART.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220220085526.808674-4-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The RISC-V AIA (Advanced Interrupt Architecture) defines a new
interrupt controller for MSIs (message signal interrupts) called
IMSIC (Incoming Message Signal Interrupt Controller). The IMSIC
is per-HART device and also suppport virtualizaiton of MSIs using
dedicated VS-level guest interrupt files.
This patch adds device emulation for RISC-V AIA IMSIC which
supports M-level, S-level, and VS-level MSIs.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-Id: <20220220085526.808674-3-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We extend virt machine to emulate AIA APLIC devices only when
"aia=aplic" parameter is passed along with machine name in QEMU
command-line. When "aia=none" or not specified then we fallback
to original PLIC device emulation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220220085526.808674-2-anup@brainfault.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Add new macros to manipulate signed fields within the register.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220301215958.157011-2-richard.henderson@linaro.org
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There are no longer any VMStateDescription structs in the tree which
use the load_state_old support for custom handling of incoming
migration from very old QEMU. Remove the mechanism entirely.
This includes removing one stray useless setting of
minimum_version_id_old in a VMStateDescription with no load_state_old
function, which crept in after the global weeding-out of them in
commit 17e3134061.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20220215175705.3846411-1-peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
* ppc/pnv fixes
* PMU EBB support
* target/ppc: PowerISA Vector/VSX instruction batch
* ppc/pnv: Extension of the powernv10 machine with XIVE2 ans PHB5 models
* spapr allocation cleanups
-----BEGIN PGP SIGNATURE-----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=kWv5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-ppc-20220302' into staging
ppc-7.0 queue
* ppc/pnv fixes
* PMU EBB support
* target/ppc: PowerISA Vector/VSX instruction batch
* ppc/pnv: Extension of the powernv10 machine with XIVE2 ans PHB5 models
* spapr allocation cleanups
# gpg: Signature made Wed 02 Mar 2022 11:00:42 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-ppc-20220302: (87 commits)
hw/ppc/spapr_vio.c: use g_autofree in spapr_dt_vdevice()
hw/ppc/spapr_rtas.c: use g_autofree in rtas_ibm_get_system_parameter()
spapr_pci_nvlink2.c: use g_autofree in spapr_phb_nvgpu_ram_populate_dt()
hw/ppc/spapr_numa.c: simplify spapr_numa_write_assoc_lookup_arrays()
hw/ppc/spapr_drc.c: use g_autofree in spapr_drc_by_index()
hw/ppc/spapr_drc.c: use g_autofree in spapr_dr_connector_new()
hw/ppc/spapr_drc.c: use g_autofree in drc_unrealize()
hw/ppc/spapr_drc.c: use g_autofree in drc_realize()
hw/ppc/spapr_drc.c: use g_auto in spapr_dt_drc()
hw/ppc/spapr_caps.c: use g_autofree in spapr_caps_add_properties()
hw/ppc/spapr_caps.c: use g_autofree in spapr_cap_get_string()
hw/ppc/spapr_caps.c: use g_autofree in spapr_cap_set_string()
hw/ppc/spapr.c: fail early if no firmware found in machine_init()
hw/ppc/spapr.c: use g_autofree in spapr_dt_chosen()
pnv/xive2: Add support for 8bits thread id
pnv/xive2: Add support for automatic save&restore
xive2: Add a get_config() handler for the router configuration
pnv/xive2: Add support XIVE2 P9-compat mode (or Gen1)
ppc/pnv: add XIVE Gen2 TIMA support
pnv/xive2: Introduce new capability bits
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
- restore TESTS/IMAGES filtering to docker tests
- add NOUSER to alpine image
- bump lcitool version
- move arm64/s390x cross build images to lcitool
- add aarch32 runner CI scripts
- expand testing to more vectors
- update s390x jobs to focal for gitlab/travis
- disable threadcount for all sh4
- fix semihosting SYS_HEAPINFO and test
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEZoWumedRZ7yvyN81+9DbCVqeKkQFAmIdGJEACgkQ+9DbCVqe
KkQZYQf+Ndlm651dulO4J55puk8cUOMrCrDvqVkxM/V7ZD4GKyoa9/PstfOspLkQ
hXNANtfcr7zsXxo7J7PKVpX3y+upxCMLLK9NqHXW3O8mOSoru44caLko6FdmwWkU
KmoToEM3jgxJxqrE8ijLz1gxo79TVT0m3OyyKlMf9C+Wf4BfUe4NXjt/VMcecrDd
wKJnvjWyrk67yOyPRDnT2XlG1HdphD90g8xPxiK1tzkEQEWJlojTLSZENQksa1V6
JBu1mwT/KPodkllzTQcHHjGn4/vsdzFqjqV+8d3xXiSmr/QdeyByUeDhJ7aI4qdY
aKoX3hoIUdENmPxqXozuVBy/S4gLoA==
=MY0T
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/stsquad/tags/pull-testing-and-semihosting-280222-1' into staging
Testing and semihosting updates:
- restore TESTS/IMAGES filtering to docker tests
- add NOUSER to alpine image
- bump lcitool version
- move arm64/s390x cross build images to lcitool
- add aarch32 runner CI scripts
- expand testing to more vectors
- update s390x jobs to focal for gitlab/travis
- disable threadcount for all sh4
- fix semihosting SYS_HEAPINFO and test
# gpg: Signature made Mon 28 Feb 2022 18:46:41 GMT
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-and-semihosting-280222-1:
tests/tcg: port SYS_HEAPINFO to a system test
semihosting/arm-compat: replace heuristic for softmmu SYS_HEAPINFO
tests/tcg: completely disable threadcount for sh4
gitlab: upgrade the job definition for s390x to 20.04
travis.yml: Update the s390x jobs to Ubuntu Focal
tests/tcg: add vectorised sha512 versions
tests/tcg: add sha512 test
tests/tcg: build sha1-vector with O3 and compare
tests/tcg/ppc64: clean-up handling of byte-reverse
gitlab: add a new aarch32 custom runner definition
scripts/ci: allow for a secondary runner
scripts/ci: add build env rules for aarch32 on aarch64
tests/docker: introduce debian-riscv64-test-cross
tests/docker: update debian-s390x-cross with lcitool
tests/docker: update debian-arm64-cross with lcitool
tests/lcitool: update to latest version
tests/docker: add NOUSER for alpine image
tests/docker: restore TESTS/IMAGES filtering
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The XIVE interrupt controller on P10 can automatically save and
restore the state of the interrupt registers under the internal NVP
structure representing the VCPU. This saves a costly store/load in
guest entries and exits.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Add GEN1 config even if we don't use it yet in the core framework.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Only the CAM line updates done by the hypervisor are specific to
POWER10. Instead of duplicating the TM ops table, we handle these
commands locally under the PowerNV XIVE2 model.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
When the Address-Based Interrupt Trigger mode is activated, the PHB
maps the interrupt source number into the interrupt command address.
The PHB directly triggers the IC ESB page of the interrupt number and
not the notify page of the IC anymore.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The PQ_disable configuration bit disables the check done on the PQ
state bits when processing new MSI interrupts. When bit 9 is enabled,
the PHB forwards any MSI trigger to the XIVE interrupt controller
without checking the PQ state bits. The XIVE IC knows from the trigger
message that the PQ bits have not been checked and performs the check
locally.
This configuration bit only applies to MSIs and LSIs are still checked
on the PHB to handle the assertion level.
PQ_disable enablement is a requirement for StoreEOI.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The trigger message coming from a HW source contains a special bit
informing the XIVE interrupt controller that the PQ bits have been
checked at the source or not. Depending on the value, the IC can
perform the check and the state transition locally using its own PQ
state bits.
The following changes add new accessors to the XiveRouter required to
query and update the PQ state bits. This only applies to the PowerNV
machine. sPAPR accessors are provided but the pSeries machine should
not be concerned by such complex configuration for the moment.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
This is an internal offset used to inject triggers when the PQ state
bits are not controlled locally. Such as for LSIs when the PHB5 are
using the Address-Based Interrupt Trigger mode and on the END.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
and use a pnv_chip_power10_quad_realize() helper to avoid code
duplication with P9. This still needs some refinements on the XSCOM
registers handling in PnvQuad.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Our OCC model is very mininal and POWER10 can simply reuse the OCC
model we introduced for POWER9.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The XIVE2 interrupt controller of the POWER10 processor follows the
same logic than on POWER9 but the HW interface has been largely
reviewed. It has a new register interface, different BARs, extra
VSDs, new layout for the XIVE2 structures, and a set of new features
which are described below.
This is a model of the POWER10 XIVE2 interrupt controller for the
PowerNV machine. It focuses primarily on the needs of the skiboot
firmware but some initial hypervisor support is implemented for KVM
use (escalation).
Support for new features will be implemented in time and will require
new support from the OS.
* XIVE2 BARS
The interrupt controller BARs have a different layout outlined below.
Each sub-engine has now own its range and the indirect TIMA access was
replaced with a set of pages, one per CPU, under the IC BAR:
- IC BAR (Interrupt Controller)
. 4 pages, one per sub-engine
. 128 indirect TIMA pages
- TM BAR (Thread Interrupt Management Area)
. 4 pages
- ESB BAR (ESB pages for IPIs)
. up to 1TB
- END BAR (ESB pages for ENDs)
. up to 2TB
- NVC BAR (Notification Virtual Crowd)
. up to 128
- NVPG BAR (Notification Virtual Process and Group)
. up to 1TB
- Direct mapped Thread Context Area (reads & writes)
OPAL does not use the grouping and crowd capability.
* Virtual Structure Tables
XIVE2 adds new tables types and also changes the field layout of the END
and NVP Virtualization Structure Descriptors.
- EAS
- END new layout
- NVT was splitted in :
. NVP (Processor), 32B
. NVG (Group), 32B
. NVC (Crowd == P9 block group) 32B
- IC for remote configuration
- SYNC for cache injection
- ERQ for event input queue
The setup is slighly different on XIVE2 because the indexing has changed
for some of the tables, block ID or the chip topology ID can be used.
* XIVE2 features
SCOM and MMIO registers have a new layout and XIVE2 adds a new global
capability and configuration registers.
The lowlevel hardware offers a set of new features among which :
- a configurable number of priorities : 1 - 8
- StoreEOI with load-after-store ordering is activated by default
- Gen2 TIMA layout
- A P9-compat mode, or Gen1, TIMA toggle bit for SW compatibility
- increase to 24bit for VP number
Other features will have some impact on the Hypervisor and guest OS
when activated, but this is not required for initial support of the
controller.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The VP space is larger in XIVE2 (P10), 24 bits instead of 19bits on
XIVE (P9), and the CAM line can use a 7bits or 8bits thread id.
For now, we only use 7bits thread ids, same as P9, but because of the
change of the size of the VP space, the CAM matching routine is
different between P9 and P10. It is easier to duplicate the whole
routine than to add extra handlers in xive_presenter_tctx_match() used
for P9.
We might come with a better solution later on, after we have added
some more support for the XIVE2 controller.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The XIVE2 interrupt controller of the POWER10 processor as the same
logic as on POWER9 but its SW interface has been largely reworked. The
interrupt controller has a new register interface, different BARs,
extra VSDs. These will be described when we add the device model for
the baremetal machine.
The XIVE internal structures for the EAS, END, NVT have different
layouts which is a problem for the current core XIVE framework. To
avoid adding too much complexity in the XIVE models, a new XIVE2 core
framework is introduced. It duplicates the models which are closely
linked to the XIVE internal structures : Xive2Router and
Xive2ENDSource and reuses the XiveSource, XivePresenter, XiveTCTX
models, as they are more generic.
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Following the implementation of tcg_gen_gvec_3i, add a four-vector and
immediate operand expansion method.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Matheus Ferst <matheus.ferst@eldorado.org.br>
Message-Id: <20220225210936.1749575-34-matheus.ferst@eldorado.org.br>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The dh_alias redirect is intended to handle TCG types as distinguished
from C types. TCG does not distinguish signed int from unsigned int,
because they are the same size. However, we need to retain this
distinction for dh_typecode, lest we fail to extend abi types properly
for the host call parameters.
This bug was detected when running the 'arm' emulator on an s390
system. The s390 uses TCG_TARGET_EXTEND_ARGS which triggers code
in tcg_gen_callN to extend 32 bit values to 64 bits; the incorrect
sign data in the typemask for each argument caused the values to be
extended as unsigned values.
This simple program exhibits the problem:
static volatile int num = -9;
static volatile int den = -5;
int main(void)
{
int quo = num / den;
printf("num %d den %d quo %d\n", num, den, quo);
exit(0);
}
When run on the broken qemu, this results in:
num -9 den -5 quo 0
The correct result is:
num -9 den -5 quo 1
Fixes: 7319d83a73 ("tcg: Combine dh_is_64bit and dh_is_signed to dh_typecode")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/876
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Reported-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Tested-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
* Removal of the swift-bmc machine
* New Secure Boot Controller model
* Improvements on the rainier machine
* Various small cleanups
-----BEGIN PGP SIGNATURE-----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=0F2M
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/legoater/tags/pull-aspeed-20220227' into staging
aspeed queue:
* Removal of the swift-bmc machine
* New Secure Boot Controller model
* Improvements on the rainier machine
* Various small cleanups
# gpg: Signature made Sun 27 Feb 2022 08:45:45 GMT
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20220227:
aspeed/sdmc: Add trace events
aspeed/smc: Add an address mask on segment registers
aspeed: Introduce a create_pca9552() helper
aspeed: rainier: Add strap values taken from hardware
aspeed: rainier: Add i2c LED devices
ast2600: Add Secure Boot Controller model
arm: Remove swift-bmc machine
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The previous numbers were a guess at best and rather arbitrary without
taking into account anything that might be loaded. Instead of using
guesses based on the state of registers implement a new function that:
a) scans the MemoryRegions for the largest RAM block
b) iterates through all "ROM" blobs looking for the biggest gap
The "ROM" blobs include all code loaded via -kernel and the various
-device loader techniques.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Cc: Andrew Strauss <astrauss11@gmail.com>
Cc: Keith Packard <keithp@keithp.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220225172021.3493923-18-alex.bennee@linaro.org>
Only a limited set of bits are used for decoding the Start and End
addresses of the mapping window of a flash device.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Just a stub that indicates the system has booted in secure boot mode.
Used for testing the driver:
https://lore.kernel.org/all/20211019080608.283324-1-joel@jms.id.au/
Signed-off-by: Joel Stanley <joel@jms.id.au>
[ clg: - Fixed typo
- Adjusted Copyright dates ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
* Some small fixes for the qtests
* Misc header cleanups by Philippe
-----BEGIN PGP SIGNATURE-----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=/azS
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/thuth-gitlab/tags/pull-request-2022-02-21' into staging
* Improve virtio-net failover test
* Some small fixes for the qtests
* Misc header cleanups by Philippe
# gpg: Signature made Mon 21 Feb 2022 11:40:37 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/thuth-gitlab/tags/pull-request-2022-02-21: (25 commits)
hw/tricore: Remove unused and incorrect header
hw/m68k/mcf: Add missing 'exec/hwaddr.h' header
exec/exec-all: Move 'qemu/log.h' include in units requiring it
softmmu/runstate: Clean headers
linux-user: Add missing "qemu/timer.h" include
target: Add missing "qemu/timer.h" include
core/ptimers: Remove unnecessary 'sysemu/cpus.h' include
exec/ramblock: Add missing includes
qtest: Add missing 'hw/qdev-core.h' include
hw/acpi/memory_hotplug: Remove unused 'hw/acpi/pc-hotplug.h' header
hw/remote: Add missing include
hw/tpm: Clean includes
scripts: Remove the old switch-timer-api script
tests/qtest: failover: migration abort test with failover off
tests/qtest: failover: test migration if the guest doesn't support failover
tests/qtest: failover: check migration with failover off
tests/qtest: failover: check missing guest feature
tests/qtest: failover: check the feature is correctly provided
tests/qtest: failover: use a macro for check_one_card()
tests/qtest: failover: clean up pathname of tests
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The "hardware version" machinery (qemu_set_hw_version(),
qemu_hw_version(), and the QEMU_HW_VERSION define) is used by fewer
than 10 files. Move it out from osdep.h into a new
qemu/hw-version.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-6-peter.maydell@linaro.org
The qemu_icache_linesize, qemu_icache_linesize_log,
qemu_dcache_linesize, and qemu_dcache_linesize_log variables are not
used in many files. Move them out of osdep.h to a new
qemu/cacheinfo.h, and document them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-5-peter.maydell@linaro.org
The QEMU_MAP_* constants are used only as arguments to the
qemu_ram_mmap() function. Move them to mmap-alloc.h, where that
function's prototype is defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-4-peter.maydell@linaro.org
The qemu_mprotect_*() family of functions are used in very few files;
move them from osdep.h to a new qemu/mprotect.h.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-3-peter.maydell@linaro.org
The function qemu_madvise() and the QEMU_MADV_* constants associated
with it are used in only 10 files. Move them out of osdep.h to a new
qemu/madvise.h header that is included where it is needed.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220208200856.3558249-2-peter.maydell@linaro.org
TriCore boards certainly don't need the ARM loader API :)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220214183144.27402-4-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
hwaddr type is defined in "exec/hwaddr.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220209215446.58402-3-f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Many files use "qemu/log.h" declarations but neglect to include
it (they inherit it via "exec/exec-all.h"). "exec/exec-all.h" is
a core component and shouldn't be used that way. Move the
"qemu/log.h" inclusion locally to each unit requiring it.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20220207082756.82600-10-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
"exec/ramblock.h" requires "qemu/rcu.h" for the definition of
rcu_head, and "exec/ramlist.h" for the definition of RAMBlockNotifier.
Add them to avoid when when refactoring include/:
include/exec/ramblock.h:26:21: error: field has incomplete type 'struct rcu_head'
struct rcu_head rcu;
^
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20220207082756.82600-6-f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Security label improvements from Vivek
- includes a fix for building against new kernel headers
[V3: checkpatch style fixes]
[V2: Fix building on old Linux]
Blocking flock disable from Sebastian
SYNCFS support from Greg
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
-----BEGIN PGP SIGNATURE-----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=K93e
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/dgilbert-gitlab/tags/pull-virtiofs-20220217b' into staging
V3: virtiofs pull 2022-02-17
Security label improvements from Vivek
- includes a fix for building against new kernel headers
[V3: checkpatch style fixes]
[V2: Fix building on old Linux]
Blocking flock disable from Sebastian
SYNCFS support from Greg
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
# gpg: Signature made Thu 17 Feb 2022 17:24:25 GMT
# gpg: using RSA key 45F5C71B4A0CB7FB977A9FA90516331EBC5BFDE7
# gpg: Good signature from "Dr. David Alan Gilbert (RH2) <dgilbert@redhat.com>" [full]
# Primary key fingerprint: 45F5 C71B 4A0C B7FB 977A 9FA9 0516 331E BC5B FDE7
* remotes/dgilbert-gitlab/tags/pull-virtiofs-20220217b:
virtiofsd: Add basic support for FUSE_SYNCFS request
virtiofsd: Add an option to enable/disable security label
virtiofsd: Create new file using O_TMPFILE and set security context
virtiofsd: Create new file with security context
virtiofsd: Add helpers to work with /proc/self/task/tid/attr/fscreate
virtiofsd: Move core file creation code in separate function
virtiofsd, fuse_lowlevel.c: Add capability to parse security context
virtiofsd: Extend size of fuse_conn_info->capable and ->want fields
virtiofsd: Parse extended "struct fuse_init_in"
linux-headers: Update headers to v5.17-rc1
virtiofsd: Fix breakage due to fuse_init_in size change
virtiofsd: Do not support blocking flock
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This implements the Nested KVM HV hcall API for spapr under TCG.
The L2 is switched in when the H_ENTER_NESTED hcall is made, and the
L1 is switched back in returned from the hcall when a HV exception
is sent to the vhyp. Register state is copied in and out according to
the nested KVM HV hcall API specification.
The hdecr timer is started when the L2 is switched in, and it provides
the HDEC / 0x980 return to L1.
The MMU re-uses the bare metal radix 2-level page table walker by
using the get_pate method to point the MMU to the nested partition
table entry. MMU faults due to partition scope errors raise HV
exceptions and accordingly are routed back to the L1.
The MMU does not tag translations for the L1 (direct) vs L2 (nested)
guests, so the TLB is flushed on any L1<->L2 transition (hcall entry
and exit).
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[ clg: checkpatch fixes ]
Message-Id: <20220216102545.1808018-10-npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Machines which don't emulate the HDEC facility are able to use the
timer for something else. Provide functions to start and stop the
hdecr timer.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[ clg: checkpatch fixes ]
Message-Id: <20220216102545.1808018-4-npiggin@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
The patch adds support for the SCM flush hcall for the nvdimm devices.
To be available for exploitation by guest through the next patch. The
hcall is applicable only for new SPAPR specific device class which is
also introduced in this patch.
The hcall expects the semantics such that the flush to return with
H_LONG_BUSY_ORDER_10_MSEC when the operation is expected to take longer
time along with a continue_token. The hcall to be called again by providing
the continue_token to get the status. So, all fresh requests are put into
a 'pending' list and flush worker is submitted to the thread pool. The
thread pool completion callbacks move the requests to 'completed' list,
which are cleaned up after collecting the return status for the guest
in subsequent hcall from the guest.
The semantics makes it necessary to preserve the continue_tokens and
their return status across migrations. So, the completed flush states
are forwarded to the destination and the pending ones are restarted
at the destination in post_load. The necessary nvdimm flush specific
vmstate structures are also introduced in this patch which are to be
saved in the new SPAPR specific nvdimm device to be introduced in the
following patch.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <164396254862.109112.16675611182159105748.stgit@ltczzess4.aus.stglabs.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
A new subclass inheriting NVDIMMDevice is going to be introduced in
subsequent patches. The new subclass uses the realize and unrealize
callbacks. Add them on NVDIMMClass to appropriately call them as part
of plug-unplug.
Signed-off-by: Shivaprasad G Bhat <sbhat@linux.ibm.com>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <164396253158.109112.1926755104259023743.stgit@ltczzess4.aus.stglabs.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Update headers to 5.17-rc1. I need latest fuse changes.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Message-Id: <20220208204813.682906-3-vgoyal@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
The RISC-V AIA (Advanced Interrupt Architecture) defines a new
interrupt controller for wired interrupts called APLIC (Advanced
Platform Level Interrupt Controller). The APLIC is capabable of
forwarding wired interupts to RISC-V HARTs directly or as MSIs
(Message Signaled Interupts).
This patch adds device emulation for RISC-V AIA APLIC.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-id: 20220204174700.534953-19-anup@brainfault.org
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch removes the left-over/unused `ibex_plic.h` file. Previously
used by opentitan, which now follows the RISC-V standard and uses the
SiFivePlicState.
Fixes: 434e7e021 ("hw/intc: Remove the Ibex PLIC")
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220121055005.3159846-1-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Coroutine pool size was 64 from long ago, and the basis was organized in the commit message in 4d68e86b.
At that time, virtio-blk queue-size and num-queue were not configuable, and equivalent values were 128 and 1.
Coroutine pool size 64 was fine then.
Later queue-size and num-queue got configuable, and default values were increased.
Coroutine pool with size 64 exhausts frequently with random disk IO in new size, and slows down.
This commit adjusts coroutine pool size adaptively with new values.
This commit adds 64 by default, but now coroutine is not only for block devices,
and is not too much burdon comparing with new default.
pool size of 128 * vCPUs.
Signed-off-by: Hiroki Narukawa <hnarukaw@yahoo-corp.jp>
Message-id: 20220214115302.13294-2-hnarukaw@yahoo-corp.jp
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add support for TP 4076 ("Zoned Random Write Area"), v2021.08.23
("Ratified").
This adds three new namespace parameters: "zoned.numzrwa" (number of
zrwa resources, i.e. number of zones that can have a zrwa),
"zoned.zrwas" (zrwa size in LBAs), "zoned.zrwafg" (granularity in LBAs
for flushes).
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
Add struct for Zone Management Send in preparation for more zone send
flags.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Klaus Jensen <k.jensen@samsung.com>
TARGET_ABI_FMT_lx isn't available for softmmu which causes confusion
when trying to print. As abi_ptr == target_ulong use its format string
instead.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Now we have no TCG trace events and no longer handle them in the code
we can remove the handling from the tracetool to generate them. vcpu
tracing is still available although the existing syscall event is an
exercise in redundancy (plugins and -strace can also get the
information).
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cc: Luis Vilanova <vilanova@imperial.ac.uk>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20220204204335.1689602-21-alex.bennee@linaro.org>
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Cc: Luis Vilanova <vilanova@imperial.ac.uk>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220204204335.1689602-20-alex.bennee@linaro.org>
Currently we track in the TableDesc and CmdQDesc structs the state of
the GITS_BASER<n> and GITS_CBASER Valid bits. However we aren't very
consistent abut checking the valid field: we test it in update_cte()
and update_dte(), but not anywhere else we look things up in tables.
The GIC specification says that it is UNPREDICTABLE if a guest fails
to set any of these Valid bits before enabling the ITS via
GITS_CTLR.Enabled. So we can choose to handle Valid == 0 as
equivalent to a zero-length table. This is in fact how we're already
catching this case in most of the table-access paths: when Valid is 0
we leave the num_entries fields in TableDesc or CmdQDesc set to zero,
and then the out-of-bounds check "index >= num_entries" that we have
to do anyway before doing any of these table lookups will always be
true, catching the no-valid-table case without any extra code.
So we can remove the checks on the valid field from update_cte()
and update_dte(): since these happen after the bounds check there
was never any case when the test could fail. That means the valid
fields would be entirely unused, so just remove them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220201193207.2771604-11-peter.maydell@linaro.org
We use the arm_boot_info::nb_cpus field in only one place, and that
place can easily get the number of CPUs locally rather than relying
on the board code to have set the field correctly. (At least one
board, xlnx-versal-virt, does not set the field despite having more
than one CPU.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-16-peter.maydell@linaro.org
If we're using PSCI emulation to start secondary CPUs, there is no
point in writing the "secondary boot" stub code, because it will
never be used -- secondary CPUs start powered-off, and when powered
on are set to begin execution at the address specified by the guest's
power-on PSCI call, not at the stub.
Move the call to the hook that writes the secondary boot stub code so
that we can do it only if we're starting a Linux kernel and not using
PSCI.
(None of the users of the hook care about the ordering of its call
relative to anything else: they only use it to write a rom blob to
guest memory.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-14-peter.maydell@linaro.org
Instead of setting the CPU psci-conduit and start-powered-off
properties in the xlnx-versal-virt board code, set the arm_boot_info
psci_conduit field so that the boot.c code can do it.
This will fix a corner case where we were incorrectly enabling PSCI
emulation when booting guest code into EL3 because it was an ELF file
passed to -kernel. (EL3 guest code started via -bios, -pflash, or
the generic loader was already being run with PSCI emulation
disabled.)
Note that EL3 guest code has no way to turn on the secondary CPUs
because there's no emulated power controller, but this was already
true for EL3 guest code run via -bios, -pflash, or the generic
loader.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20220127154639.2090164-8-peter.maydell@linaro.org
Currently we expect board code to set the psci-conduit property on
CPUs and ensure that secondary CPUs are created with the
start-powered-off property set to false, if the board wishes to use
QEMU's builtin PSCI emulation. This worked OK for the virt board
where we first wanted to use it, because the virt board directly
creates its CPUs and is in a reasonable position to set those
properties. For other boards which model real hardware and use a
separate SoC object, however, it is more awkward. Most PSCI-using
boards just set the psci-conduit board unconditionally.
This was never strictly speaking correct (because you would not be
able to run EL3 guest firmware that itself provided the PSCI
interface, as the QEMU implementation would overrule it), but mostly
worked in practice because for non-PSCI SMC calls QEMU would emulate
the SMC instruction as normal (by trapping to guest EL3). However,
we would like to make our PSCI emulation follow the part of the SMCC
specification that mandates that SMC calls with unknown function
identifiers return a failure code, which means that all SMC calls
will be handled by the PSCI code and the "emulate as normal" path
will no longer be taken.
We tried to implement that in commit 9fcd15b919
("arm: tcg: Adhere to SMCCC 1.3 section 5.2"), but this
regressed attempts to run EL3 guest code on the affected boards:
* mcimx6ul-evk, mcimx7d-sabre, orangepi, xlnx-zcu102
* for the case only of EL3 code loaded via -kernel (and
not via -bios or -pflash), virt and xlnx-versal-virt
so for the 7.0 release we reverted it (in commit 4825eaae4f).
This commit provides a mechanism that boards can use to arrange that
psci-conduit is set if running guest code at a low enough EL but not
if it would be running at the same EL that the conduit implies that
the QEMU PSCI implementation is using. (Later commits will convert
individual board models to use this mechanism.)
We do this by moving the setting of the psci-conduit and
start-powered-off properties to arm_load_kernel(). Boards which want
to potentially use emulated PSCI must set a psci_conduit field in the
arm_boot_info struct to the type of conduit they want to use (SMC or
HVC); arm_load_kernel() will then set the CPUs up accordingly if it
is not going to start the guest code at the same or higher EL as the
fake QEMU firmware would be at.
Board/SoC code which uses this mechanism should no longer set the CPU
psci-conduit property directly. It should only set the
start-powered-off property for secondaries if EL3 guest firmware
running bare metal expects that rather than the alternative "all CPUs
start executing the firmware at once".
Note that when calculating whether we are going to run guest
code at EL3, we ignore the setting of arm_boot_info::secure_board_setup,
which might cause us to run a stub bit of guest code at EL3 which
does some board-specific setup before dropping to EL2 or EL1 to
run the guest kernel. This is OK because only one board that
enables PSCI sets secure_board_setup (the highbank board), and
the stub code it writes will behave the same way whether the
one SMC call it makes is handled by "emulate the SMC" or by
"PSCI default returns an error code". So we can leave that stub
code in place until after we've changed the PSCI default behaviour;
at that point we will remove it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20220127154639.2090164-4-peter.maydell@linaro.org
'Or' the IRQs coming from the QSPI and QSPI DMA models. This is done for
avoiding the situation where one of the models incorrectly deasserts an
interrupt asserted from the other model (which will result in that the IRQ
is lost and will not reach guest SW).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220203151742.1457-1-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This change exposes ACPI ERST support for x86 guests.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-8-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This change introduces the public defintions for ACPI ERST.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Reviewed-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-5-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This change reserves the PCI device_id for the new ACPI ERST
device.
Signed-off-by: Eric DeVolder <eric.devolder@oracle.com>
Acked-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Ani Sinha <ani@anisinha.ca>
Message-Id: <1643402289-22216-4-git-send-email-eric.devolder@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
The comment "disk I/O throttling" doesn't make any sense at all
any more. It was added in commit 0563e19151 to describe
bdrv_io_limits_enable()/disable(), which were removed in commit
97148076, so the comment is just a forgotten leftover.
Suggested-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Emanuele Giuseppe Esposito <eesposit@redhat.com>
Message-Id: <20220131125615.74612-1-eesposit@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
The vhost-user-blk export runs requests asynchronously in their own
coroutine. When the vhost connection goes away and we want to stop the
vhost-user server, we need to wait for these coroutines to stop before
we can unmap the shared memory. Otherwise, they would still access the
unmapped memory and crash.
This introduces a refcount to VuServer which is increased when spawning
a new request coroutine and decreased before the coroutine exits. The
memory is only unmapped when the refcount reaches zero.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20220125151435.48792-1-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
* Update copyright dates to 2022
* hw/armv7m: Fix broken VMStateDescription
* hw/char/exynos4210_uart: Fix crash on trying to load VM state
* rtc: Move RTC function prototypes to their own header
* xlnx-versal-virt: Support PMC SLCR
* xlnx-versal-virt: Support OSPI flash memory controller
* scripts: Explain the difference between linux-headers and standard-headers
* target/arm: Log CPU index in 'Taking exception' log
* arm_gicv3_its: Various bugfixes and cleanups
* arm_gicv3_its: Implement the missing MOVI and MOVALL commands
* ast2600: Fix address mapping of second SPI controller
* target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
-----BEGIN PGP SIGNATURE-----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=m7N5
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20220128' into staging
target-arm queue:
* Update copyright dates to 2022
* hw/armv7m: Fix broken VMStateDescription
* hw/char/exynos4210_uart: Fix crash on trying to load VM state
* rtc: Move RTC function prototypes to their own header
* xlnx-versal-virt: Support PMC SLCR
* xlnx-versal-virt: Support OSPI flash memory controller
* scripts: Explain the difference between linux-headers and standard-headers
* target/arm: Log CPU index in 'Taking exception' log
* arm_gicv3_its: Various bugfixes and cleanups
* arm_gicv3_its: Implement the missing MOVI and MOVALL commands
* ast2600: Fix address mapping of second SPI controller
* target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
# gpg: Signature made Fri 28 Jan 2022 15:29:36 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20220128: (32 commits)
target/arm: Use correct entrypoint for SVC taken from Hyp to Hyp
hw/arm: ast2600: Fix address mapping of second SPI controller
hw/intc/arm_gicv3_its: Implement MOVI
hw/intc/arm_gicv3_its: Implement MOVALL
hw/intc/arm_gicv3_its: Check table bounds against correct limit
hw/intc/arm_gicv3_its: Make GITS_BASER<n> RAZ/WI for unimplemented registers
hw/intc/arm_gicv3_its: Provide read accessor for translation_ops
hw/intc/arm_gicv3: Set GICR_CTLR.CES if LPIs are supported
hw/intc/arm_gicv3_redist: Remove unnecessary zero checks
hw/intc/arm_gicv3_its: Sort ITS command list into numeric order
hw/intc/arm_gicv3: Honour GICD_CTLR.EnableGrp1NS for LPIs
hw/intc/arm_gicv3_its: Don't clear GITS_CWRITER on writes to GITS_CBASER
hw/intc/arm_gicv3_its: Don't clear GITS_CREADR when GITS_CTLR.ENABLED is set
hw/intc/arm_gicv3: Initialise dma_as in GIC, not ITS
hw/intc/arm_gicv3_its: Add tracepoints
target/arm: Log CPU index in 'Taking exception' log
scripts: Explain the difference between linux-headers and standard-headers
MAINTAINERS: Remove myself (for raspi).
MAINTAINERS: Add an entry for Xilinx Versal OSPI
hw/arm/xlnx-versal-virt: Connect mt35xu01g flashes to the OSPI
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently when we fill in a TableDesc based on the value the guest
has written to the GITS_BASER<n> register, we calculate both:
* num_entries : the number of entries in the table, constrained
by the amount of memory the guest has given it
* num_ids : the number of IDs we support for this table,
constrained by the implementation choices and the architecture
(eg DeviceIDs are 16 bits, so num_ids is 1 << 16)
When validating ITS commands, however, we check only num_ids,
thus allowing a broken guest to specify table entries that
index off the end of it. This will only corrupt guest memory,
but the ITS is supposed to reject such commands as invalid.
Instead of calculating both num_entries and num_ids, set
num_entries to the minimum of the two limits, and check that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20220122182444.724087-13-peter.maydell@linaro.org
Connect the OSPI flash memory controller model (including the source and
destination DMA).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20220121161141.14389-8-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of Xilinx Versal's OSPI flash memory controller.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-7-francisco.iglesias@xilinx.com
[PMM: fixed indent]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
An option on real hardware when embedding a DMA engine into a peripheral
is to make the peripheral control the engine through a custom DMA control
(hardware) interface between the two. Software drivers in this scenario
configure and trigger DMA operations through the controlling peripheral's
register API (for example, writing a specific bit in a register could
propagate down to a transfer start signal on the DMA control interface).
At the same time the status, results and interrupts for the transfer might
still be intended to be read and caught through the DMA engine's register
API (and signals).
This patch adds a class 'read' method for allowing to start read transfers
from peripherals embedding and controlling the Xilinx CSU DMA engine as in
above scenario.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-6-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add in the missing includes in the header for being able to build the DMA
model when reusing it.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-5-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an orgate and 'or' the interrupts from the BBRAM and RTC models.
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-3-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of Versal's PMC SLCR (system-level control registers).
Signed-off-by: Francisco Iglesias <francisco.iglesias@xilinx.com>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc@lmichel.fr>
Message-id: 20220121161141.14389-2-francisco.iglesias@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
softmmu/rtc.c defines two public functions: qemu_get_timedate() and
qemu_timedate_diff(). Currently we keep the prototypes for these in
qemu-common.h, but most files don't need them. Move them to their
own header, a new include/sysemu/rtc.h.
Since the C files using these two functions did not need to include
qemu-common.h for any other reason, we can remove those include lines
when we add the include of the new rtc.h.
The license for the .h file follows that of the softmmu/rtc.c
where both the functions are defined.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
It's a new year; update the copyright strings for our
help/version/about information and for our documentation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220120124713.288303-1-peter.maydell@linaro.org
vof.h requires "qom/object.h" for DECLARE_CLASS_CHECKERS(),
"exec/memory.h" for address_space_read/write(),
"exec/address-spaces.h" for address_space_memory
and more importantly "cpu.h" for target_ulong.
vof.c doesn't need "exec/ram_addr.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220122003104.84391-1-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
"host" pages are related to the *host* not the *target*,
thus the qemu_host_page_size / qemu_host_page_mask variables
and the HOST_PAGE_ALIGN() / REAL_HOST_PAGE_ALIGN() macros
can be moved to "exec/cpu-common.h" which is target agnostic.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Message-Id: <20220120000836.229419-1-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The functions are only used within their respective source files, so no
need for exporting.
Signed-off-by: Bernhard Beschow <shentey@gmail.com>
Message-Id: <20220116122327.73048-1-shentey@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that RISC-V Spike machine can use BIN BIOS images, we remove
the macros used for ELF BIOS image names.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Currently, we have to use OpenSBI firmware ELF as bios for the spike
machine because the HTIF console requires ELF for parsing "fromhost"
and "tohost" symbols.
The latest OpenSBI can now optionally pick-up HTIF register address
from HTIF DT node so using this feature spike machine can now use
OpenSBI firmware BIN as bios.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Get kernel and fdt start address in virt.c, and pass them to KVM
when cpu reset. Add kvm_riscv.h to place riscv specific interface.
In addition, PLIC is created without M-mode PLIC contexts when KVM
is enabled.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Mingwang Li <limingwang@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-id: 20220112081329.1835-7-jiangyifei@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This change fixes a bug where a write only register is read.
As per https://docs.opentitan.org/hw/ip/rv_timer/doc/#register-table
the 'INTR_TEST0' register is write only.
Signed-off-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20220110051606.4031241-1-alistair.francis@opensource.wdc.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Mark Cave-Ayland
Peter Maydell
Bernhard Beschow
Titus Rwantare
Shengtan Mao
Cédric Le Goater
Daniel P. Berrangé
Richard Henderson
Christian Schoenebeck
Keno Fischer
Vladimir Sementsov-Ogievskiy
Philippe Mathieu-Daudé
Liav Albani
Sergio Lopez
Igor Mammedov
Joelle van Dyne
zhenwei pi
Łukasz Gieryk
Knut Omang
Jean-Philippe Brucker
Jason Wang
Ziqiao Kong
Emanuele Giuseppe Esposito
Hanna Reitz
Stefan Hajnoczi
Viresh Kumar
Xueming Li
Naveen Nagar
Wilfred Mallawa
Anup Patel
Matheus Ferst
Alex Bennée
Joel Stanley
Nicholas Piggin
Shivaprasad G Bhat
Vivek Goyal
Vitaly Chikunov
Hiroki Narukawa
Klaus Jensen
Ivanov Arkady
Francisco Iglesias
Eric DeVolder
Kevin Wolf
Anup Patel
Yifei Jiang