Update tlb->PFN to contain PFN concatenated with PFNX. PFNX is 0 if large
physical address is not supported.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Extend EntryLo0, EntryLo1, LLAddr and TagLo from 32 to 64 bits in MIPS32.
Introduce gen_move_low32() function which moves low 32 bits from 64-bit
temp to GPR; it sign extends 32-bit value on MIPS64 and truncates on
MIPS32.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
ERETNC is identical to ERET except that an ERETNC will not clear the LLbit
that is set by execution of an LL instruction, and thus when placed between
an LL and SC sequence, will never cause the SC to fail.
Presence of ERETNC is denoted by the Config5.LLB.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
MIPS SIMD Architecture vector loads and stores require misalignment support.
MSA Memory access should work as an atomic operation. Therefore, it has to
check validity of all addresses for a vector store access if it is spanning
into two pages.
Separating helper functions for each data format as format is known in
translation.
To use mmu_idx from cpu_mmu_index() instead of calculating it from hflag.
Removing save_cpu_state() call in translation because it is able to use
cpu_restore_state() on fault as GETRA() is passed.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
[leon.alrae@imgtec.com: remove unused do_* functions]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Release 6 requires misaligned memory access support for all ordinary memory
access instructions (for example, LW/SW, LWC1/SWC1).
However misaligned support is not provided for certain special memory accesses
such as atomics (for example, LL/SC).
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
This relatively small architectural feature adds the following:
FIR.FREP: Read-only. If FREP=1, then Config5.FRE and Config5.UFE are
available.
Config5.FRE: When enabled all single-precision FP arithmetic instructions,
LWC1/LWXC1/MTC1, SWC1/SWXC1/MFC1 cause a Reserved Instructions
exception.
Config5.UFE: Allows user to write/read Config5.FRE using CTC1/CFC1
instructions.
Enable the feature in MIPS64R6-generic CPU.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Move the "Tests" group of functions so that gen_load_fpr32() and
gen_store_fpr32() can use generate_exception().
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
On ARM the MSI data corresponds to the shared peripheral interrupt (SPI)
ID. This latter equals to the SPI index + 32. to retrieve the SPI index,
matching the gsi, an architecture specific function is introduced.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let kvm_arch_post_run convert fields in the kvm_run struct to MemTxAttrs.
These are then passed to address_space_rw.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
PC needs to be saved if an exception can be generated by an helper.
This fixes a problem related to resuming the execution at unexpected address
after an exception (caused by MSA load/store instruction) has been serviced.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
All instructions which may change hflags terminate tb. However, this doesn't
work if such an instruction is placed in delay or forbidden slot.
gen_branch() clears MIPS_HFLAG_BMASK in ctx->hflags and then generates code
to overwrite hflags with ctx->hflags, consequently we loose any execution-time
hflags modifications. For example, in the following scenario hflag related to
Status.CU1 will not be updated:
/* Set Status.CU1 in delay slot */
mfc0 $24, $12, 0
lui $25, 0x2000
or $25, $25, $24
b check_Status_CU1
mtc0 $25, $12, 0
With this change we clear MIPS_HFLAG_BMASK in execution-time hflags if
instruction in delay or forbidden slot wants to terminate tb for some reason
(i.e. ctx->bstate != BS_NONE).
Also, die early and loudly if "unknown branch" is encountered as this should
never happen.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
CP0.BadVAddr is supposed to capture the most recent virtual address that caused
the exception. Currently this does not work correctly for unaligned instruction
fetch as translation is not stopped and CP0.BadVAddr is updated with subsequent
addresses.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
This is improved type checking for the translators -- it's no longer
possible to accidentally swap arguments to the branch functions.
Note that the code generating backends still manipulate labels as int.
With notable exceptions, the scope of the change is just a few lines
for each target, so it's not worth building extra machinery to do this
change in per-target increments.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Cc: Anthony Green <green@moxielogic.com>
Cc: Jia Liu <proljc@gmail.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
A bunch of fixes all over the place, some of the
bugs fixed are actually regressions.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVAH/uAAoJECgfDbjSjVRprq0H/iyqLSHQIv6gNOPYQbLXOCv0
pkCeLx6kTMO9lSwxZcsZvMsYPeiEL3CHRKJcEjq0+Ap0uen0pa2Yl3WzyJcnBcib
xwkHk/UftFYAiZAzVtd4moXujvVLYNL1ukvr/wPOdIkTEn8U6K3NaT3pLooc369f
oTyQhlL3E9HJ5S6X0HXJIFwtsOIhPfS3NCLoDFbFjtb9mIsqTx7N5s2C5hctF+ir
JtyuwPx5oT73WYxoYmjSP6n/Nf5cuJdqtm6o2KijjhWWYMJ6epYVBo/DD6dIFbmJ
V/23dxpon+lvhae2c2LAVrkiJ1Boon/eMbJK/mNwpFX7vW35ataLPy6pYpaiEJs=
=RUld
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
misc fixes and cleanups
A bunch of fixes all over the place, some of the
bugs fixed are actually regressions.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed Mar 11 17:48:30 2015 GMT using RSA key ID D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream: (25 commits)
virtio-scsi: remove empty wrapper for cmd
virtio-scsi: clean out duplicate cdb field
virtio-scsi: fix cdb/sense size
uapi/virtio_scsi: allow overriding CDB/SENSE size
virtio-scsi: drop duplicate CDB/SENSE SIZE
exec: don't include hw/boards for linux-user
acpi: specify format for build_append_namestring
MAINTAINERS: drop aliguori@amazon.com
tpm: Move memory subregion function into realize function
virtio-pci: Convert to realize()
pci: Convert pci_nic_init() to Error to avoid qdev_init()
machine: query mem-merge machine property
machine: query dump-guest-core machine property
hw/boards: make it safe to include for linux-user
machine: query phandle-start machine property
machine: query kvm-shadow-mem machine property
kvm: add machine state to kvm_arch_init
machine: query kernel-irqchip property
machine: allowed/required kernel-irqchip support
machine: replace qemu opts with iommu property
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Changes:
* use VMStateDescription for MIPS CPU
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJVAFjgAAoJEFIRjjwLKdpr9EUH/3zCVgTGT8s2lQxKxK1Fit93
BJCEM4bdJfynBe6ZMLn7W9MnwKXZTaKaK7M3u3Z4SX6S54entTUYrG6ubNaE18Em
i+ZRVVMys2KNXIkMfgI9E6bXEl7xhFVAKmRAQTmXRPclbQPhYUJLwmqVxVeXuQoO
OUvx6SxeDC5zzSjIt91//FSu5QNaSAg/sfxcHAZyqNDcKUw7W6tXXCGQnveYQsj0
21n9cdo4y8vgS8uiQo4/MEn2Ptw+uN6X4XhSwOdZy0g6K9AUjo39ySbKJk7YTvtS
YoD+jvIzPiBB7L3RFV8ATk9OewxlMGGb+4opSadLNef3OsSoe3hPkY4CvL9AYIA=
=8ApH
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/lalrae/tags/mips-20150311' into staging
MIPS patches 2015-03-11
Changes:
* use VMStateDescription for MIPS CPU
# gpg: Signature made Wed Mar 11 15:01:52 2015 GMT using RSA key ID 0B29DA6B
# gpg: Can't check signature: public key not found
* remotes/lalrae/tags/mips-20150311:
target-mips: add missing MSACSR and restore fp_status and hflags
target-mips: replace cpu_save/cpu_load with VMStateDescription
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Needed to query machine's properties.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Save MSACSR state. Also remove fp_status, msa_fp_status, hflags and restore
them in post_load() from the architectural registers.
Float exception flags are not present in vmstate. Information they carry
is used only by softfloat caller who translates them into MIPS FCSR.Cause,
FCSR.Flags and then they are cleared. Therefore there is no need for saving
them in vmstate.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Create VMStateDescription for MIPS CPU. The new structure contains exactly the
same fields as before, therefore leaving existing version_id.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Using rs = -1 in gen_logic_imm() for microMIPS LUI instruction is dangerous
and may bite us when implementing microMIPS R6 because in R6 AUI and LUI
are distinguished by rs value. Therefore use 0 for safety.
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Recently added CP0.BadInstr and CP0.BadInstrP registers ended up in cpu_load()
under different offset than in cpu_save(). These and all registers between were
incorrectly restored.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
The test is supposed to terminate TB if the end of the page is reached.
However, with current implementation it may never succeed for microMIPS or
mips16.
Reported-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Maciej W. Rozycki <macro@linux-mips.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The method by which we count the number of ops emitted
is going to change. Abstract that away into some inlines.
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Commit fecd264 added a number of fall-throughs, but neglected to
properly document them as intentional. Commit d922445 cleaned that up
for many, but not all cases. Take care of the remaining ones.
Spotted by Coverity.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Expand out STATUS_PARAM wherever it is used and delete the definition.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Use cpu_*_data instead of the direct *_raw load/store accessors.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1421334118-3287-9-git-send-email-peter.maydell@linaro.org
The TARGET_HAS_ICE #define is intended to indicate whether a target-*
guest CPU implementation supports the breakpoint handling. However,
all our guest CPUs have that support (the only two which do not
define TARGET_HAS_ICE are unicore32 and openrisc, and in both those
cases the bp support is present and the lack of the #define is just
a bug). So remove the #define entirely: all new guest CPU support
should include breakpoint handling as part of the basic implementation.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1420484960-32365-1-git-send-email-peter.maydell@linaro.org
on s390 MSI-X irqs are presented as thin or adapter interrupts
for this we have to reorganize the routing entry to contain
valid information for the adapter interrupt code on s390.
To minimize impact on existing code we introduce an architecture
function to fixup the routing entry.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Pavel Dovgalyuk <pavel.dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* remotes/lalrae/tags/mips-20141216: (30 commits)
target-mips: remove excp_names[] from linux-user as it is unused
disas/mips: disable unused mips16_to_32_reg_map[]
disas/mips: remove unused mips_msa_control_names_numeric[32]
target-mips: convert single case switch into if statement
target-mips: Fix DisasContext's ulri member initialization
target-mips: Use local float status pointer across MSA macros
target-mips: Add missing calls to synchronise SoftFloat status
linux-user: Use the 5KEf processor for 64-bit emulation
target-mips: Also apply the CP0.Status mask to MTTC0
target-mips: gdbstub: Clean up FPU register handling
target-mips: Correct 32-bit address space wrapping
target-mips: Tighten ISA level checks
target-mips: Fix CP0.Config3.ISAOnExc write accesses
target-mips: Output CP0.Config2-5 in the register dump
target-mips: Fix the 64-bit case for microMIPS MOVE16 and MOVEP
target-mips: Correct the writes to Status and Cause registers via gdbstub
target-mips: Correct the handling of writes to CP0.Status for MIPSr6
target-mips: Correct MIPS16/microMIPS branch size calculation
target-mips: Restore the order of helpers
target-mips: Remove unused `FLOAT_OP' macro
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Running barebox on qemu-system-mips* with '-d unimp' overloads
stderr by very very many mips_cpu_handle_mmu_fault() messages:
mips_cpu_handle_mmu_fault address=b80003fd ret 0 physical 00000000180003fd prot 3
mips_cpu_handle_mmu_fault address=a0800884 ret 0 physical 0000000000800884 prot 3
mips_cpu_handle_mmu_fault pc a080cd80 ad b80003fd rw 0 mmu_idx 0
So it's very difficult to find LOG_UNIMP message.
The mips_cpu_handle_mmu_fault() messages appear on enabling ANY
logging! It's not very handy.
Adding separate log category for *_cpu_handle_mmu_fault()
logging fixes the problem.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Acked-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Message-id: 1418489298-1184-1-git-send-email-antonynpavlov@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Set DisasContext's ulri member to 0 or 1 as with other bool members.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reduce line wrapping throughout MSA helper macros by using a local float
status pointer rather than referring to the float status through the
environment each time. No functional change.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add missing calls to synchronise the SoftFloat status with the CP1.FSCR:
+ for the rounding and flush-to-zero modes upon processor reset,
+ for the flush-to-zero mode on FSCR updates through the GDB stub.
Refactor code accordingly and remove the redundant RESTORE_ROUNDING_MODE
macro.
Signed-off-by: Thomas Schwinge <thomas@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Make CP0.Status writes made with the MTTC0 instruction respect this
register's mask just like all the other places. Also preserve the
current values of masked out bits.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Rewrite the FPU register access parts of `mips_cpu_gdb_read_register'
and `mips_cpu_gdb_write_register' for consistency between each other.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Make sure the address space is unconditionally wrapped on 32-bit
processors, that is ones that do not implement at least the MIPS III
ISA.
Also make MIPS16 SAVE and RESTORE instructions use address calculation
rather than plain arithmetic operations for stack pointer manipulation
so that their semantics for stack accesses follows the architecture
specification. That in particular applies to user software run on
64-bit processors with the CP0.Status.UX bit clear where the address
space is wrapped to 32 bits.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Tighten ISA level checks down to MIPS II that many of our instructions
are missing. Also make sure any 64-bit instruction enables are only
applied to 64-bit processors, that is ones that implement at least the
MIPS III ISA.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Fix CP0.Config3.ISAOnExc write accesses on microMIPS processors. This
bit is mandatory for any processor that implements the microMIPS
instruction set. This bit is r/w for processors that implement both the
standard MIPS and the microMIPS instruction set. This bit is r/o and
hardwired to 1 if only the microMIPS instruction set is implemented.
There is no other bit ever writable in CP0.Config3 so defining a
corresponding `CP0_Config3_rw_bitmask' member in `CPUMIPSState' is I
think an overkill. Therefore make the ability to write the bit rely on
the presence of ASE_MICROMIPS set in the instruction flags.
The read-only case of the microMIPS instruction set being implemented
only can be added when we add support for such a configuration. We do
not currently have such support, we have no instruction flag that would
control the presence of the standard MIPS instruction set nor any
associated code in instruction decoding.
This change is needed to boot a microMIPS Linux kernel successfully,
otherwise it hangs early on as interrupts are enabled and then the
exception handler invoked loops as its first instruction is interpreted
in the wrong execution mode and triggers another exception right away.
And then over and over again.
We already check the current setting of the CP0.Config3.ISAOnExc in
`set_hflags_for_handler' to set the ISA bit correctly on the exception
handler entry so it is the ability to set it that is missing only.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Include CP0.Config2 through CP0.Config5 registers in the register dump
produced with the `info registers' monitor command. Align vertically
with the registers already output.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Fix microMIPS MOVE16 and MOVEP instructions on 64-bit processors by
using register addition operations.
This copies the approach taken with MIPS16 MOVE instructions (I8_MOV32R
and I8_MOVR32 opcodes) and follows the observation that OPC_ADDU expands
to tcg_gen_mov_tl whenever `rt' is 0 and `rs' is not, therefore copying
`rs' to `rd' verbatim. This is not the case with OPC_ADDIU where a
sign-extension from bit #31 is made, unless in the uninteresting case of
`rs' being 0, losing the upper 32 bits of the value copied for any
proper 64-bit values.
This also serves as an optimization as one op is produced in generated
code rather than two (again, unless `rs' is 0, where it doesn't change
anything).
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Make writes to CP0.Status and CP0.Cause have the same effect as
executing corresponding MTC0 instructions would in Kernel Mode. Also
ignore writes in the user emulation mode.
Currently for requests from the GDB stub we write all the bits across
both registers, ignoring any read-only locations, and do not synchronise
the environment to evaluate side effects. We also write these registers
in the user emulation mode even though a real kernel presents them as
read only.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Correct these issues with the handling of CP0.Status for MIPSr6:
* only ignore the bit pattern of 0b11 on writes to CP0.Status.KSU, that
is for processors that do implement Supervisor Mode, let the bit
pattern be written to CP0.Status.UM:R0 freely (of course the value
written to read-only CP0.Status.R0 will be discarded anyway); this is
in accordance to the relevant architecture specification[1],
* check the newly written pattern rather than the current contents of
CP0.Status for the KSU bits being 0b11,
* use meaningful macro names to refer to CP0.Status bits rather than
magic numbers.
References:
[1] "MIPS Architecture For Programmers, Volume III: MIPS64 / microMIPS64
Privileged Resource Architecture", MIPS Technologies, Inc., Document
Number: MD00091, Revision 6.00, March 31, 2014, Table 9.45 "Status
Register Field Descriptions", pp. 210-211.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Correct MIPS16/microMIPS branch size calculation in PC adjustment
needed:
- to set the value of CP0.ErrorEPC at the entry to the reset exception,
- for the purpose of branch reexecution in the context of device I/O.
Follow the approach taken in `exception_resume_pc' for ordinary, Debug
and NMI exceptions.
MIPS16 and microMIPS branches can be 2 or 4 bytes in size and that has
to be reflected in calculation. Original MIPS ISA branches, which is
where this code originates from, are always 4 bytes long, just as all
original MIPS ISA instructions.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Restore the order of helpers that used to be: unary operations (generic,
then MIPS-specific), binary operations (generic, then MIPS-specific),
compare operations. At one point FMA operations were inserted at a
random place in the file, disregarding the preexisting order, and later
on even more operations sprinkled across the file. Revert the mess by
moving FMA operations to a new ternary class inserted after the binary
class and move the misplaced unary and binary operations to where they
belong.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Remove the `FLOAT_OP' macro, unused since commit
b6d96beda3 [Use temporary registers for
the MIPS FPU emulation.].
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Move the call to `update_fcr31' in `helper_float_cvtw_s' after the
exception flag check, for consistency with the remaining helpers that do
it last too.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Enable vectored interrupt support for the 74Kf CPU, reflecting hardware.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add the M14K and M14Kc processors from MIPS Technologies that are the
original implementation of the microMIPS ISA. They are dual instruction
set processors, implementing both the microMIPS and the standard MIPSr32
ISA.
These processors correspond to the M4K and 4KEc CPUs respectively,
except with support for the microMIPS instruction set added, support for
the MCU ASE added and two extra interrupt lines, making a total of 8
hardware interrupts plus 2 software interrupts. The remaining parts of
the microarchitecture, in particular the pipeline, stayed unchanged.
The presence of the microMIPS ASE is is reflected in the configuration
added. We currently have no support for the MCU ASE, including in
particular the ACLR, ASET and IRET instructions in either encoding, and
we have no support for the extra interrupt lines, including bits in
CP0.Status and CP0.Cause registers, so these features are not marked,
making our support diverge from real hardware.
Signed-off-by: Sandra Loosemore <sandra@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Make the data type used for the CP0.Config4 and CP0.Config5 registers
and their mask signed, for consistency with the remaining 32-bit CP0
registers, like CP0.Config0, etc.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Add the 5KEc and 5KEf processors from MIPS Technologies that are the
original implementation of the MIPS64r2 ISA.
Silicon for these processors has never been taped out and no soft cores
were released even. They do exist though, a CP0.PRId value has been
assigned and experimental RTLs produced at the time the MIPS64r2 ISA has
been finalized. The settings introduced here faithfully reproduce that
hardware.
As far the implementation goes these processors are the same as the 5Kc
and the 5Kf CPUs respectively, except implementing the MIPS64r2 rather
than the original MIPS64 instruction set. There must have been some
updates to the CP0 architecture as mandated by the ISA, such as the
addition of the EBase register, although I am not sure about the exact
details, no documentation has ever been produced for these processors.
The remaining parts of the microarchitecture, in particular the
pipeline, stayed unchanged. Or to put it another way, the difference
between a 5K and a 5KE CPU corresponds to one between a 4K and a 4KE
CPU, except for the 64-bit rather than 32-bit ISA.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
CP1.FIR is read-only in hardware so gdbstub must respect it. We already
respect it for CTC1 instructions, so do it here too.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Fix an off-by-one error in `mips_cpu_gdb_write_register' for register
matching how `mips_cpu_gdb_read_register' handles it. This register
slot is a fake anyway, there's nothing in hardware that corresponds to
it.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Avoid to allocate different TCG registers for the FPU registers
that are mapped on the MSA vectore registers.
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Correct the way PC is updated when single-stepping instructions, by
keeping the old PC only for the BS_EXCP (exception condition) state.
Some MTC0 (and possibly other) instructions switch to the BS_STOP state
to terminate the current translation block, so that the state transition
of the simulated CPU resulting from the CP0 operation takes effect with
the following instruction. This happens with `mtc0 <reg>,c0_config' for
example, typically used to set KSEG0 cacheability.
While single-stepping this has a side-effect of not advancing the PC
past the instruction just executed; subsequent single-step traps will
stop at the same instruction repeatedly. Example:
(gdb) stepi
0x80004d24 in _start ()
5: x/i $pc
=> 0x80004d24 <_start+364>: mfc0 t1,c0_config
(gdb)
0x80004d28 in _start ()
5: x/i $pc
=> 0x80004d28 <_start+368>: li at,-8
(gdb)
0x80004d2c in _start ()
5: x/i $pc
=> 0x80004d2c <_start+372>: and t1,t1,at
(gdb)
0x80004d30 in _start ()
5: x/i $pc
=> 0x80004d30 <_start+376>: ori t1,t1,0x3
(gdb)
0x80004d34 in _start ()
5: x/i $pc
=> 0x80004d34 <_start+380>: mtc0 t1,c0_config
(gdb)
0x80004d34 in _start ()
5: x/i $pc
=> 0x80004d34 <_start+380>: mtc0 t1,c0_config
(gdb)
0x80004d34 in _start ()
5: x/i $pc
=> 0x80004d34 <_start+380>: mtc0 t1,c0_config
(gdb)
0x80004d34 in _start ()
5: x/i $pc
=> 0x80004d34 <_start+380>: mtc0 t1,c0_config
(gdb)
-- oops!
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
New R6 COP1 conditional branches currently don't have delay slot. Fixing this
by setting MIPS_HFLAG_BDS32 flag which is required for branches having 4-byte
delay slot.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Set the CP0.Config3.DSP2P bit for the 74kf processor and both that bit
and the CP0.Config3.DSP bit for the artificial mips32r5-generic and
mips64dspr2 processors. They have the DSPr2 ASE enabled in `insn_flags'
and CPUs that implement that ASE need to have both CP0.Config3.DSP and
CP0.Config3.DSP2P set or software won't detect its presence.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
[leon.alrae@imgtec.com: remove DSP flags from mips32r5-generic]
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Define macros for CP0.Config3 and CP0.Config4 bits. These used to be
exhaustive as at MIPS32r3, but more bits may have been added since.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Make microMIPS FP branches respect CP0.Status.CU1 and trap with a
Coprocessor Unusable exception if COP1 has been disabled; also trap if
no FPU is present at all.
Standard MIPS FP instruction encodings have a more regular structure and
branches are covered with a single umbrella along other instructions.
This is not the case with the microMIPS encoding, this case has to be
taken care of explicitly here. Code to do so has been copied from the
standard MIPS code handler for OPC_CP1, in `decode_opc'.
Problems arising from this bug will generally only show up on user
context switches in operating systems making use of lazy FP context
switches, such as Linux. It will also more readily trigger if software
FPU emulation is used, either implicitly on a non-float CPU, or forced
on a hard-float CPU such as with the "nofpu" Linux kernel command line
argument.
The problem may have been easily missed because we have no hard-float
microMIPS CPU configuration present; in fact we have no microMIPS CPU
configuration of any kind present.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA support to mips32r5-generic core definition
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA MI10 format instructions
update LSA and DLSA for MSA
add 16, 64 bit load and store
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA BIT format instructions
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA I5 format instructions
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA I8 format instructions
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add msa_helper.c
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add msa_reset() and global msa register (d type only)
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA opcode enum
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
stop translation as ctc1 instruction can change hflags
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Remove the duplicated ieee_rm in gdbstub.c.
Make the other ieee_rm and ieee_ex_to_mips available to other files.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add MSA exceptions
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
add defines and data structure for MIPS SIMD Architecture
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Release 6 limits the number of cases where software can cause UNDEFINED or
UNPREDICTABLE behaviour. In this case, when accessing reserved / unimplemented
CP0 register, writes are ignored and reads return 0.
In pre-R6 the behaviour is not specified, but generating RI exception is not
what the real HW does.
Additionally, remove CP0 Random register as it became reserved in Release 6.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
In Release 6 not all the values are allowed to be written to a register.
If the value is not valid or unsupported then it should stay unchanged.
For pre-R6 the existing behaviour has been changed only for CP0_Index register
as the current implementation does not seem to be correct - it looks like it
tries to limit the input value but the limit is higher than the actual
number of tlb entries.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
When conditional compact branch is encountered decode one more instruction in
current translation block - that will be forbidden slot. Instruction in
forbidden slot will be executed only if conditional compact branch is not taken.
Any control transfer instruction (CTI) which are branches, jumps, ERET,
DERET, WAIT and PAUSE will generate RI exception if executed in forbidden or
delay slot.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
SDBBP instruction Reserved Instruction control. The purpose of this field is
to restrict availability of SDBBP to kernel mode operation.
If the bit is set then SDBBP instruction can only be executed in kernel mode.
User execution of SDBBP will cause a Reserved Instruction exception.
Additionally add missing Config4 and Config5 cases for dm{f,t}c0.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
BadInstr Register (CP0 Register 8, Select 1)
The BadInstr register is a read-only register that capture the most recent
instruction which caused an exception.
BadInstrP Register (CP0 Register 8, Select 2)
The BadInstrP register contains the prior branch instruction, when the
faulting instruction is in a branch delay slot.
Using error_code to indicate whether AdEL or TLBL was triggered during
instruction fetch, in this case BadInstr is not updated as valid instruction
word is not available.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Leon Alrae
Yongbok Kim
Eric Auger
Paolo Bonzini
Peter Maydell
Stefan Weil
Richard Henderson
Marcel Apfelbaum
Eduardo Habkost
Maciej W. Rozycki
Markus Armbruster
Frank Blaschka
Antony Pavlov