Commit c643bed99 moved qemu_init_vcpu() calls to common CPUState code.
This causes x86 cpu-add to fail with "KVM: setting VAPIC address failed".
The reason for the failure is that CPUClass::kvm_fd is not yet
initialized in the following call graph:
->x86_cpu_realizefn
->x86_cpu_apic_realize
->qdev_init
->device_set_realized
->device_reset (hotplugged == 1)
->apic_reset_common
->vapic_base_update
->kvm_apic_vapic_base_update
This causes attempted KVM vCPU ioctls to fail.
By contrast, in the non-hotplug case the APIC is reset much later, when
the vCPU is already initialized.
As a quick and safe solution, move the qemu_init_vcpu() call back into
the targets' realize functions.
Reported-by: Chen Fan <chen.fan.fnst@cn.fujitsu.com>
Acked-by: Igor Mammedov <imammedo@redhat.com> (for i386)
Tested-by: Jia Liu <proljc@gmail.com> (for openrisc)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Multiplication of two fractional word elements is not correct when sign
extension/promotion is needed. This change fixes it by adding correct
casts from unsigned to signed values.
In addition, the tests (dpaq_sa_l_w.c and dpsq_sa_l_w.c) have been extended
to trigger the current issue.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This assignment causes a compiler warning for compilations with the compiler
option -Wunused-but-set-variable (which is included with -Wextra).
Removing it allows using -Wextra for QEMU code without suppressing too many
extra warnings.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This change corrects rounding and saturation of Q31 fractional value in
mipsdsp_trunc16_sat16_round(). Overflow detection was incorrect for the
corner case for PRECRQ_RS.PH, and this test case is also part of the change.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When a branch delay slot contains another branch instruction, the code
generated raises an exception, however since is_branch==1,
handle_delay_slot() doesn't get called immediately. This means
ctx->bstate isn't set to BS_BRANCH, and the decoder continues decoding
until a non-branch instruction is found.
If the first branch was a branch likely instruction then each
instruction after it generates code for the unlikely case, to go to the
next tb starting after the delay slot. This results in multiple goto_tb
tcg ops being generated with the same exit number. When debug is enabled
this hits:
tcg-op.h:2589: tcg_gen_goto_tb: Assertion `(tcg_ctx.goto_tb_issue_mask & (1 << idx)) == 0' failed.
This is fixed by removing is_branch entirely, and calling
handle_delay_slot() if (ctx.hflags & MIPS_HFLAG_BMASK) was set prior to
the current instruction being decoded. This still prevents
handle_delay_slot() being called immediately after a branch but allows
it to still be called after a branch within a delay slot.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Multiplication of Q15 fractional halfword vectors was incorrect in the
previous implementation of mipsdsp_rndq15_mul_q15_q15. It failed to take
element signs into account. This change fixes it, and it adds a test case
for it.
The change also removes unnecessary cast in the function
mipsdsp_mul_q15_q15_overflowflag21().
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Completes migration of target-specific code to new target-*/gdbstub.c.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Acked-by: Max Filippov <jcmvbkbc@gmail.com> (for xtensa)
Signed-off-by: Andreas Färber <afaerber@suse.de>
This avoids polluting the global namespace with a non-prefixed macro and
makes it obvious in the call sites that we return.
Semi-automatic conversion using, e.g.,
sed -i 's/GET_REGL(/return gdb_get_regl(mem_buf, /g' target-*/gdbstub.c
followed by manual tweaking for sparc's GET_REGA() and Coding Style.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Acked-by: Max Filippov <jcmvbkbc@gmail.com> (for xtensa)
Signed-off-by: Andreas Färber <afaerber@suse.de>
CPUState::gdb_num_regs replaces num_g_regs.
CPUClass::gdb_num_core_regs replaces NUM_CORE_REGS.
Allows building gdb_register_coprocessor() for xtensa, too.
As a side effect this should fix coprocessor register numbering for SMP.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Acked-by: Max Filippov <jcmvbkbc@gmail.com> (for xtensa)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Change breakpoint_invalidate() argument to CPUState alongside.
Since all targets now assign a softmmu-only field, we can drop helpers
cpu_class_set_{do_unassigned_access,vmsd}() and device_class_set_vmsd().
Prepares for changing cpu_memory_rw_debug() argument to CPUState.
Acked-by: Max Filippov <jcmvbkbc@gmail.com> (for xtensa)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Prepares for changing cpu_single_step() argument to CPUState.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Signed-off-by: Andreas Färber <afaerber@suse.de>
Where no extra implementation is needed, fall back to CPUClass::set_pc().
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Signed-off-by: Andreas Färber <afaerber@suse.de>
This moves setting the Program Counter from gdbstub into target code.
Use vaddr type as upper-bound replacement for target_ulong.
Signed-off-by: Andreas Färber <afaerber@suse.de>
x86 was using additional CPU_DUMP_* flags, so make that configurable in
CPUClass::reset_dump_flags.
This adds reset logging for alpha, unicore32 and xtensa.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Since commit 878096eeb2 (cpu: Turn
cpu_dump_{state,statistics}() into CPUState hooks) CPUArchState is no
longer needed.
Add documentation and make the functions available through qemu/log.h
outside NEED_CPU_H to allow use in qom/cpu.c. Moving them to qom/cpu.h
was not yet possible due to convoluted include paths, so that some
devices grow an implicit and unneeded dependency on qom/cpu.h for now.
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Reviewed-by: Richard Henderson <rth@twiddle.net>
[AF: Simplified mb_cpu_do_interrupt() and do_interrupt_all() changes]
Signed-off-by: Andreas Färber <afaerber@suse.de>
Also use bool type while at it.
Prepares for moving singlestep_enabled field to CPUState.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Move next_cpu from CPU_COMMON to CPUState.
Move first_cpu variable to qom/cpu.h.
gdbstub needs to use CPUState::env_ptr for now.
cpu_copy() no longer needs to save and restore cpu_next.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
[AF: Rebased, simplified cpu_copy()]
Signed-off-by: Andreas Färber <afaerber@suse.de>
A transition from CPUFooState to FooCPU can be considered safe,
just like FooCPU::env access in the opposite direction.
The only benefit of the FOO_CPU() casts would be protection against
bogus CPUFooState pointers, but then surrounding code would likely
break, too.
This should slightly improve interrupt etc. performance when going from
CPUFooState to FooCPU.
For any additional CPU() casts see 3556c233d9
(qom: allow turning cast debugging off).
Reported-by: Anthony Liguori <aliguori@us.ibm.com>
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
The functions cpu_clone_regs() and cpu_set_tls() are not purely CPU
related -- they are specific to the TLS ABI for a a particular OS.
Move them into the linux-user/ tree where they belong.
target-lm32 had entirely unused implementations, since it has no
linux-user target; just drop them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Use it for all targets, but be careful not to pass invalid CPUState.
cpu_single_env can be NULL, e.g. on Xen.
Signed-off-by: Andreas Färber <afaerber@suse.de>
This allows to move the call into CPUState's realizefn.
Therefore move the stub into libqemustub.a.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Make cpustats monitor command available unconditionally.
Prepares for changing kvm_handle_internal_error() and kvm_cpu_exec()
arguments to CPUState.
Signed-off-by: Andreas Färber <afaerber@suse.de>
The current ISA mode needs to be saved in bit 0 of the resume address.
If the current instruction happens to be in a branch delay slot, then
the address of the preceding jump instruction should be stored instead.
exception_resume_pc already does both of these tasks, so it is
made available and reused.
MIPS_HFLAG_BMASK in hflags is cleared, otherwise QEMU may treat the
first instruction of the signal handler as a delay slot instruction.
Signed-off-by: Kwok Cheung Yeung <kcy@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This is a small follow-up change to "fix incorrect behaviour for INSV".
It includes two minor modifications:
- sizefilter is constant so it can be moved inside of the block,
- several lines of the code are replaced with a call to deposit64.
No functional change.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
First we need to clear the bit and then we set the given value.
Instruction ADDSC sets the bit and instruction ADDWC uses this bit.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This change makes sure that modifications of pos field in the DSPControl
register do not trash other bits in the register. This bug can be triggered
with the additional test case in mips32-dsp/extpdp.c in this commit.
In addition to this, this change corrects incorrect calculation of the mask
for EXTPDP.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The mask for EXTP instruction when size=31 has not been correctly
calculated.
The test (mips32-dsp/extp.c) has been extended to include the case that
triggers the issue.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Corner case for INSV instruction when size=32 has not been correctly
implemented. The mask for size should be one bit wider, and preparing the
filter variable should be aware of this case too.
The test for INSV has been extended to include the case that triggers the
bug.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The emulator needs to check in hflags if DSP unit has been turned off before
it generates code for MUL_PH, MUL_S_PH, MULQ_S_W, and MULQ_RS_W.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This change corrects and simplifies how discard is calculated for shift
left logical vector instructions. It is used to detect overflow and set bit
22 in the DSPControl register.
The existing tests (shll_ph.c, shll_qb.c) are extended with the corner cases
that expose incorrectness in the previous implementation.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The operands for MAQ_SA_W.PHL/MAQ_SA_W.PHR must in specified format.
Otherwise, the results are unpredictable. Once the operands were corrected
in the tests (part of this change), a bug in mipsdsp_mul_q15_q15 became
visible.
This change corrects the tests for MAQ_SA_W.PHL/MAQ_SA_W.PHR and fixes
sign-related issue in mipsdsp_mul_q15_q15. It also removes unnecessary
comment.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Fix for rndrashift_short_acc to set correct value to higher 64 bits.
This change also corrects conditions when bit 23 of the DSPControl register
is set.
The existing test files have been extended with several examples that
trigger the issues. One bug/example in the test file for EXTR_RS_W has been
found and reported by Klaus Peichl.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This removes a global per-target function and thus takes us one step
closer to compiling multiple targets into one executable.
It will also allow to override the interrupt handling for certain CPU
families.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Move it to qom/cpu.h to avoid issues with include order.
Change pc_acpi_smi_interrupt() opaque to X86CPU.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Move it to qom/cpu.c to avoid build failures depending on include order
of cpu-qom.h and exec/cpu-all.h.
Change opaques of various ..._irq_handler() functions to the
appropriate CPU type to facilitate using cpu_reset_interrupt().
Fix Coding Style issues while at it (missing braces, indentation).
Signed-off-by: Andreas Färber <afaerber@suse.de>
Both fields are used in VMState, thus need to be moved together.
Explicitly zero them on reset since they were located before
breakpoints.
Pass PowerPCCPU to kvmppc_handle_halt().
Signed-off-by: Andreas Färber <afaerber@suse.de>
Add accumulator arguments to gen_HILO and gen_muldiv, rather than
extracting the accumulator directly from ctx->opcode. The extraction
was only right for the standard encoding: MIPS16 doesn't have access
to the DSP registers, while microMIPS encodes the accumulator register
in a different field (bits 14 and 15).
Passing the accumulator register is probably an over-generalisation
for division and 64-bit multiplication, which never access anything
other than HI and LO, and which always pass 0 as the new argument.
Separating them felt a bit fussy though.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The previous implementation incorrectly used same macro to detect overflow
for addition and subtraction. This patch makes distinction between these
two, and creates separate macros. The affected routines are changed
accordingly.
This change also includes additions to the existing tests for SUBQ_S_PH and
SUBQ_S_W that would trigger the fixed issue, and it removes dead code from
the test file. The last test case in subq_s_w.c is a bug found/reported/
isolated by Klaus Peichl from Dolby.
Signed-off-by: Petar Jovanovic <petar.jovanovic@imgtec.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The gen_icount_start/end functions are now somewhat misnamed since they
are useful for generic "start/end of TB" code, used for more than just
icount. Rename them to gen_tb_start/end.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Introduce ENV_OFFSET macros which can be used in non-target-specific
code that needs to generate TCG instructions which reference CPUState
fields given the cpu_env register that TCG targets set up with a
pointer to the CPUArchState struct.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Correct sign-propagation before multiplication in MULQ_W helper.
The change also fixes previously incorrect expected values in the
tests for MULQ_RS.W and MULQ_S.W.
Signed-off-by: Petar Jovanovic <petarj@mips.com>
Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The change corrects sign-related issue with MULQ_S.PH. It also includes
extension to the already existing test which will trigger the issue.
Signed-off-by: Petar Jovanovic <petarj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The target-specific ENV_GET_CPU() macros have allowed us to navigate
from CPUArchState to CPUState. The reverse direction was not supported.
Avoid introducing CPU_GET_ENV() macros by initializing an untyped
pointer that is initialized in derived instance_init functions.
The field may not be called "env" due to it being poisoned.
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andreas Färber <afaerber@suse.de>
compute_hflags() will reset DSP h-flags, so MX bit should be initially set
for usermode in cpu_state_reset() if DSP ASE is implemented.
This change will bring back user-mode support for DSP ASE, since one of the
recent changes broke it.
Signed-off-by: Petar Jovanovic <petarj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Turn MADD.fmt, MSUB.fmt, NMADD.fmt and NMSUB.fmt from fused to unfused
operations, so that they behave in the same way as a separate multiplication
and addition. The instructions were only fused in early MIPS IV processors.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Sign-extend the result of LWR, as is already done for LWL. This is necessary
in the case where LWR loads the full word (i.e. the address is actually
aligned). In the other cases, it is implementation defined whether the
upper 32 bits of the result are unchanged or a copy of bit 31. The latter
seems easier to implement.
Previously the code used:
(oldval & (0xfffffffe << (31 - bitshift))) | (newval >> bitshift)
which zeroed the upper bits of the register, losing any previous sign
extension in the unaligned cases.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Make RESTORE use sign-extending rather than zero-extending loads.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
DSP instruction from the (d)append sub-class can be implemented with
TCG. Use a different function for these instructions are they are quite
different from compare-pick sub-class.
Fix BALIGN instruction for negative value, where the value should be
zero-extended before being shift to the right.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Instead of playing with bit shifting, add two unions (one for 32-bit
values, one for 64-bit ones) to access all the DSP elements with the
correct type.
This make the code easier to read and less error prone, and allow GCC
to vectorize the code in some cases.
Reviewed-by: Eric Johnson <ericj@mips.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
On CPU without DSP ASE support, a reserved instruction exception (instead of
a DSP ASE sate disabled) should be generated.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Copy insn_flags in DisasContext to avoid passing a CPUMIPSState pointer
to subroutines, as suggested by Richard Henderson. Change subroutines to
use this new field and remove the first argument.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When rd is 0, which still need to do the actually load to possibly
generate a TLB exception.
Reviewed-by: Eric Johnson <ericj@mips.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Move the declaration to qemu/cpu.h and add documentation.
The implementation still depends on CPUArchState for CPU iteration.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Note that target-alpha accesses this field from TCG, now using a
negative offset. Therefore the field is placed last in CPUState.
Pass PowerPCCPU to [kvm]ppc_fixup_cpu() to facilitate this change.
Move common parts of mips cpu_state_reset() to mips_cpu_reset().
Acked-by: Richard Henderson <rth@twiddle.net> (for alpha)
[AF: Rebased onto ppc CPU subclasses and openpic changes]
Signed-off-by: Andreas Färber <afaerber@suse.de>
This function will be touched again soon, so a good understanding of env
vs. other helps. Adopt gtk-doc style.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Eric Johnson <ericj@mips.com>
To facilitate the field movements, pass MIPSCPU to malta_mips_config();
avoid that for mips_cpu_map_tc() since callers only access MIPS Thread
Contexts, inside TCG helpers.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Helper function for dpa_w_ph, dpax_w_ph, dps_w_ph and dpsx_w_ph incorrectly
defines halfword vector elements as unsigned values. This results in wrong
output which is not triggered in the tests as they also follow this logic.
Signed-off-by: Petar Jovanovic <petarj@mips.com>
Reviewed-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The macros RESTORE_ROUNDING_MODE and RESTORE_FLUSH_MODE silently used
variable env from their callers. Using inline functions with env passed
as a function argument is more transparent.
This modification was proposed by Peter Maydell.
Cc: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Clear the DSP hflags at the start of compute_hflags. Otherwise access
is not properly disabled once enabled.
Signed-off-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
From the discussion on the ML [1], the exception limit defined by
magic number 0x100 is actually EXCP_SC defined in cpu.h. Replace the
magic number with EXCP_SC. Remove "#if 1 .. #endif" as well.
[1] http://lists.gnu.org/archive/html/qemu-devel/2012-11/msg03080.html
Signed-off-by: Chen Wei-Ren <chenwj@iis.sinica.edu.tw>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The immediate value is 9bits, should sign-extend to 16bits. The return value to
register should sign-extend to target_long, as Richard says, removing an
unnecessary cast works fun.
Signed-off-by: Dongxue Zhang <elta.era@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Macro RESTORE_FLUSH_MODE is similar to RESTORE_ROUNDING_MODE
but included a semicolon.
The code which uses that macro also includes a semicolon,
so the result was an empty statement.
Remove the superfluous semicolon from the macro definition.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The change removes some unnecessary and incorrect code for EXTR_S.H.
Further, it corrects the mask for shift value in the EXTR_ instructions. It also
extends the existing tests so they trigger the issues corrected with the change.
Signed-off-by: Petar Jovanovic <petarj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Upper 4 bits of ccond (bits 31..28 ) of DSPControl register are not used in
the MIPS32 architecture. They are used in the MIPS64 architecture. For MIPS32
these bits must be written as zero, and return zero on read.
The change fixes writes (WRDSP) and reads (RDDSP) to the register. It also fixes
the tests that use these instructions, and makes them smaller and simpler.
Signed-off-by: Petar Jovanovic <petarj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Refactor common code around calls to cpu_restore_state().
tb_find_pc() has now no external users, make it static.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
* 'master' of git.qemu-project.org:/pub/git/qemu:
target-mips: Fix incorrect shift for SHILO and SHILOV
target-mips: Fix incorrect code and test for INSV
xilinx_uartlite: Accept input after rx FIFO pop
xilinx_uartlite: suppress "cannot receive message"
xilinx_axienet: Implement R_IS behaviour
helper_shilo has not been shifting an accumulator value correctly for negative
values in 'shift' field. Minor optimization for shift=0 case.
This change also adds tests that will trigger issue and check for regressions.
Signed-off-by: Petar Jovanovic <petarj@mips.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Content of register rs should be shifted for pos before applying a mask.
This change contains both fix for the instruction and to the existing test.
Signed-off-by: Petar Jovanovic <petarj@mips.com>
Reviewed-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
I check MIPS microMIPS manual [1], and found the major opcode might
be wrong. I add a comment to explicitly indicate what manual I am refering
to, and according that manual I remove microMIPS32 major opcodes 0x1f.
As for others, like 0x16, 0x17, 0x36 and 0x37, they are for higher-order
MIPS ISA level or new revision of this microMIPS architecture. Quote
from Johnson, they are belong MIPS64 [2].
[1] http://www.mips.com/products/architectures/micromips/#specifications
MIPS Architecture for Programmers Volume II-B:
The microMIPS32 Instruction Set (Revision 3.05)
MD00582-2B-microMIPS-AFP-03.05.pdf
[2] http://www.mips.com/products/architectures/mips64/
MIPS Architecture For Programmers
Volume II-A: The MIPS64 Instruction Set
MD00087-2B-MIPS64BIS-AFP-03.51.pdf
Signed-off-by: Chen Wei-Ren <chenwj@iis.sinica.edu.tw>
Reviewed-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Current QEMU MIPS POOL32AXF encoding comes from microMIPS32
and microMIPS32 DSP. Add comment here to help reading.
Signed-off-by: Chen Wei-Ren <chenwj@iis.sinica.edu.tw>
Reviewed-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
While reading microMIPS decoding, I found a possible wrong opcode
encoding. According to [1] page 166, the bits 13..12 for MULTU is
0x01 rather than 0x00. Please review, thanks.
[1] MIPS Architecture for Programmers VolumeIV-e: The MIPS DSP
Application-Specific Extension to the microMIPS32 Architecture
Signed-off-by: Chen Wei-Ren <chenwj@iis.sinica.edu.tw>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The call to gen_logic_imm for OPC_LUI passes -1 for rs. This
causes the MIPS_DEBUG statement to seg fault due to the deference
of regnames[rs]. This patch fixes that.
Signed-off-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
(aurel32: replaced static string formating by a static string)
Pass around CPUArchState instead of using global cpu_single_env.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Acked-by: Richard Henderson <rth@twiddle.net>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Fix build on a 32 bit host:
CC mips-softmmu/target-mips/dsp_helper.o
/src/qemu/target-mips/dsp_helper.c: In function 'helper_dextr_rs_w':
/src/qemu/target-mips/dsp_helper.c:3556: error: integer constant is too large for 'long' type
/src/qemu/target-mips/dsp_helper.c: In function 'helper_extr_s_h':
/src/qemu/target-mips/dsp_helper.c:3656: error: integer constant is too large for 'long' type
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
If the guest uses a TLBWI instruction for upgrading permissions, we
don't need to flush the extra TLBs. This improve boot time performance
by about 10%.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use the deposit op instead of and hardcoded bit field insertion. It
allows the host to emit the corresponding instruction if available.
At the same time remove the (lsb > msb) test. The MIPS64R2 instruction
set manual says "Because of the instruction format, lsb can never be
greater than msb, so there is no UNPREDICATABLE case for this
instruction."
(Bug reported as LP:1071149.)
Cc: Никита Канунников <n.kanunnikov@sbtcom.ru>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The result of a division by 0, or a division of INT_MIN by -1 in the
signed case, is unpredictable. Just replace 0 by 1 in that case so that
it doesn't trigger a floating point exception on the host.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Avoid the branches in movn/movz implementation and replace them with
movcond. Also update a wrong command.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Store conditional operations only need local temps in user mode. Fix
the code to use temp local only in user mode, this spares two memory
stores in system mode.
At the same time remove a wrong a wrong copied & pasted comment,
store operations don't have a register destination.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Load/store from helpers should be avoided as they are quite
inefficient. Rewrite unaligned loads instructions using TCG and
aligned loads. The number of actual loads operations to implement
an unaligned load instruction is reduced from up to 8 to 1.
Note: As we can't rely on shift by 32 or 64 undefined behaviour,
the code loads already shift by one constants.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
load/store microMIPS helpers are reinventing the wheel. Call do_lw,
do_ll, do_sw and do_sl instead of using a macro calling the cpu_*
load/store functions.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Load/store operations use macros for historical reasons. Now that there
is no point in keeping them, replace them by direct calls to qemu_ld/st.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Rework *raise_exception*() functions so that they can be called from
other helpers, passing the return address as an argument.
Use do_raise_exception() function in update_fcr31() to correctly restore
the CPU state after an FPU exception.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
softfloat already has a few constants defined, use them instead of
redefining them in target-mips.
Rename FLOAT_SNAN32 and FLOAT_SNAN64 to FP_TO_INT32_OVERFLOW and
FP_TO_INT64_OVERFLOW as even if they have the same value, they are
technically different (and defined differently in the MIPS ISA).
Remove the unused constants.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Instead of accessing the flags from the floating point control
register after updating it, read the softfloat flags.
This is just code cleanup and should not change the behaviour.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For each FPU instruction that can trigger an FPU exception, to call
call update_fcr31() after.
Remove the manual NaN assignment in case of float to float operation, as
softfloat is already taking care of that. However for float to int
operation, the value has to be changed to the MIPS one. In the cvtpw_ps
case, the two registers have to be handled separately to guarantee
a correct final value in both registers.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Instead of clearing the softfloat exception flags before each floating
point instruction, reset them to 0 in update_fcr31() when an exception
is detected.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use the new softfloat floatXX_muladd() functions to implement the madd,
msub, nmadd and nmsub instructions. At the same time replace the name of
the helpers by the name of the instruction, as the only reason for the
previous names was to keep the macros simple.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When the CPU state after a possible retranslation is going to be handled
through code retranslation, we don't need to save the CPU state before.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When the CPU state is restored through retranslation after an exception,
btarget should also be restored.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
All switch() decoding instruction have a default entry, so it is possible
to have unused enum entries. Remove conditional definitions of MIPS64
opcode enums, as it only makes the code less readable.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add internal functions using by MIPS ASE DSP instructions.
Signed-off-by: Jia Liu <proljc@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For target-mips also change the return type to bool.
Make include paths for cpu-qom.h consistent for alpha and unicore32.
Signed-off-by: Andreas Färber <afaerber@suse.de>
[AF: Updated new target-openrisc function accordingly]
Acked-by: Richard Henderson <rth@twiddle.net> (for alpha)
With normal FP, this doesn't have much affect on the generated code,
because most of the FP operations are not CONST/PURE, and so we spill
registers in about the same frequency as the explicit load/stores.
But with Loongson multimedia instructions, which are all integral and
whose helpers are in fact CONST+PURE, this greatly improves the code.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Rename helper flags to the new ones. This is purely a mechanical change,
it's possible to use better flags by looking at the helpers.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
target_phys_addr_t is unwieldly, violates the C standard (_t suffixes are
reserved) and its purpose doesn't match the name (most target_phys_addr_t
addresses are not target specific). Replace it with a finger-friendly,
standards conformant hwaddr.
Outstanding patchsets can be fixed up with the command
git rebase -i --exec 'find -name "*.[ch]"
| xargs s/target_phys_addr_t/hwaddr/g' origin
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Needed for changing mips_vpe_sleep() argument type to MIPSCPU.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Needed for moving halted field to CPUState.
The variable name "c" is retained for MIPSCPU to leave "cpu" for CPUState.
Also change return type to bool while at it.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Needed for changing mips_vpe_is_wfi() argument type to MIPSCPU.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Free the variable name "other_cpu" for later use for MIPSCPU.
Fix off-by-one indentation while at it.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
For all targets that currently call tcg_gen_debug_insn_start,
add CPU_LOG_TB_OP_OPT to the condition that gates it.
This is useful for comparing optimization dumps, when the
pre-optimization dump is merely noise.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Implements all of the COP2 instructions except for the S<cond>
family of comparisons. The documentation is unclear for those.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
this will prevent some of the compilation errors with debugging
enabled from creeping back in.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The macro uses the DisasContext. Pass it around as needed.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Used by MIPS_DEBUG, when enabled.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add an explicit CPUState parameter instead of relying on AREG0
and switch to AREG0 free mode.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Acked-by: Aurelien Jarno <aurelien@aurel32.net>
This change updates the CPU reset sequence to use a common piece of code
that figures out CPU state flags, fixing the problem with MIPS_HFLAG_COP1X
not being set where applicable that causes floating-point MADD family
instructions (and other instructions from the MIPS IV FP subset) to trap.
As compute_hflags is now shared between op_helper.c and translate.c, the
function is now moved to a common header. There are no changes to this
function.
The problem was seen with the 24Kf MIPS32r2 processor in user emulation.
The new approach prevents system and user emulation from diverging -- all
the hflags state is initialized in one place now.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The microMIPS SWP and SDP instructions do not modify GPRs. So their
behavior is well defined when RD equals BASE. The MIPS Architecture
Verification Programs (AVPs) check that they work as expected. This
is required for AVPs to pass.
Signed-off-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The MIPS Architecture Verification Programs (AVPs) check privileged
instructions for the required privilege level. These changes are needed
to pass the AVP suite.
Signed-off-by: Eric Johnson <ericj@mips.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The kernel will emulate this instruction if it's not supported
natively. This insn is used for TLS, among other things, and
so is required by modern glibc.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The FS input to CVT.PS.S is the high half and FT is the low half.
tcg_gen_concat_i32_i64 takes the low half first, so the operands
were in the wrong order.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Read the second input operand of RECIP2.S and RECIP2.PS from FT rather
than FD. RECIP2.D is already correct.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Commits b5dc7732e1 and
be24bb4f30 optimized the code
and removed the correct setting of t0. Fix this.
gcc-4.7 detected this bug because parameter arg1 was unused
but set in set_HIT0_LO and set_HI_LOT0.
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
While running in the usermode emulator all of the required*
MIPS32r2 RDHWR hardware registers should be accessible (the
Linux kernel enables access to these same registers). Note
that these registers are still enabled when the MIPS ISA is
not release 2. This is OK since the Linux kernel emulates
access to them when they are not available in hardware.
* There is also the ULR register which is only recommended
for full release 2 compliance. Incidentally, accessing
this register in the current implementation works fine
without flipping its access bit.
Signed-off-by: Meador Inge <meadori@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This change addresses a problem where QEMU incorrectly traps on
floating-point MADD group instructions with SIGILL, at least while
emulating MIPS32r2 processors. These instructions use the COP1X major
opcode and include ones like:
madd.d $f2,$f4,$f2,$f6
Here's Nathan's original analysis of the problem:
"QEMU essentially does:
d = find_cpu (cpu_string) // get CPU definition
fpu_init (env, d) // initialize fpu state (init FCR0, basically)
cpu_reset (env)
...and the cpu_reset call clears all interesting state that fpu_init
setup, then proceeds to reinitialize all the CP0 registers...but not
FCR0."
I have verified this change with system emulation running the GDB test
suite for the mips-sde-elf target (o32, big endian, 24Kf CPU emulated),
there were 55 progressions and no regressions.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
In commit 1bba0dc932 cpu_reset()
was renamed to cpu_state_reset(), to allow introducing a new cpu_reset()
that would operate on QOM objects.
All callers have been updated except for one in target-mips, so drop all
implementations except for the one in target-mips and move the
declaration there until MIPSCPU reset can be fully QOM'ified.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Michael Walle <michael@walle.cc> (for lm32)
Acked-by: Max Filippov <jcmvbkbc@gmail.com> (for xtensa)
Acked-by: Edgar E. Iglesias <edgar.iglesias@gmail.com> (for mb + cris)
Acked-by: Alexander Graf <agraf@suse.de> (for ppc)
Acked-by: Blue Swirl <blauwirbel@gmail.com>
Commit 0f71a7095d (target-mips: QOM'ify
CPU) hooked up cpu_state_reset() to CPUClass::reset(). Dropping the
introduction of subclasses for 1.1, due to mips_def_t the reset code
could not be QOM'ified yet, i.e. cpu_state_reset() will not forward to
CPUClass::reset().
Update cpu_mips_init() with cpu_reset() nontheless, indirectly calling
cpu_state_reset(), so that generic code can be converted to call
cpu_reset().
Signed-off-by: Andreas Färber <afaerber@suse.de>
There's some dodgy application of De Morgan's law in the emulation
of the MIPS BC1ANY[24]F instructions: they end up branching only
if all CCs are false, rather than if one CC is.
Tested on mips64-linux-gnu, where it fixes the GCC MIPS3D tests.
Signed-off-by: Richard Sandiford <rdsandiford@googlemail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
* 'qom-cpu-rest.v1' of git://github.com/afaerber/qemu-cpu:
Makefile: Simplify compilation of target-*/cpu.c
target-mips: Start QOM'ifying CPU init
target-mips: QOM'ify CPU
target-m68k: Add QOM CPU subclasses
target-m68k: Start QOM'ifying CPU init
target-m68k: QOM'ify CPU reset
target-m68k: QOM'ify CPU
target-sh4: Start QOM'ifying CPU init
target-sh4: QOM'ify CPU reset
target-sh4: QOM'ify CPU
MAINTAINERS: Downgrade target-mips and target-sh4 to Odd Fixes
MAINTAINERS: Downgrade target-m68k to Odd Fixes
Move code not dependent on mips_def_t from cpu_mips_init() into a
QOM initfn, as a start.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Embed CPUMIPSState as first member of QOM MIPSCPU.
Let CPUClass::reset() call cpu_state_reset() for now.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Richard Henderson <rth@twiddle.net>
osdep.h is included via qemu-common.h.
Prepares for use of [u]int_fast*_t types in softfloat code.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Cc: Ben Taylor <bentaylor.solx86@gmail.com>
Cc: Aurélien Jarno <aurelien@aurel32.net>
Cc: Peter Maydell <peter.maydell@linaro.org>
Tested-by: Bernhard Walle <bernhard@bwalle.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Use uintptr_t instead of void * or unsigned long in
several op related functions, env->mem_io_pc and
GETPC() macro.
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The official spelling is QEMU.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
[blauwirbel@gmail.com: fixed comment style in hw/sun4m.c]
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The official spelling is QEMU.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
helper_raise_exception_err does not return, nor do helper_raise_exception
and do_unaligned_access.
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Scripted conversion:
for file in *.[hc] hw/*.[hc] hw/kvm/*.[hc] linux-user/*.[hc] linux-user/m68k/*.[hc] bsd-user/*.[hc] darwin-user/*.[hc] tcg/*/*.[hc] target-*/cpu.h; do
sed -i "s/CPUState/CPUArchState/g" $file
done
All occurrences of CPUArchState are expected to be replaced by QOM CPUState,
once all targets are QOM'ified and common fields have been extracted.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Scripted conversion:
sed -i "s/CPUState/CPUMIPSState/g" target-mips/*.[hc]
sed -i "s/#define CPUMIPSState/#define CPUState/" target-mips/cpu.h
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Frees the identifier cpu_reset for QOM CPUs (manual rename).
Don't hide the parameter type behind explicit casts, use static
functions with strongly typed argument to indirect.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
* it's -> its (fixed for all files)
* dont -> don't (only fixed in a line which was touched by the previous fix)
* distrub -> disturb (fixed in the same line)
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
accidently->accidentally
annother->another
choosen->chosen
consideres->considers
decriptor->descriptor
developement->development
paramter->parameter
preceed->precede
preceeding->preceding
priviledge->privilege
propogation->propagation
substraction->subtraction
throught->through
upto->up to
usefull->useful
Fix also grammar in posix-aio-compat.c
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alexander Graf <agraf@suse.de>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Dong Xu Wang <wdongxu@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
1. The pending need to pass the Status IM gating.
2. The priority is from seven (highest prio) down to zero.
QEMU was doing the opposite.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
These registers share some of their fields. Writes to these fields
should be visible through the corresponding mirror fields.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Parameter is_softmmu (and its evil mutant twin brother is_softmuu)
is not used in cpu_*_handle_mmu_fault() functions, remove them
and adjust callers.
Acked-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move softmmu_exec.h include directives from target-*/exec.h to
target-*/op_helper.c. Move also various other stuff only used in
op_helper.c there.
Define global env in dyngen-exec.h.
For i386, move wrappers for segment and FPU helpers from user-exec.c
to op_helper.c. Implement raise_exception_err_env() to handle dynamic
CPUState. Move the function declarations to cpu.h since they can be
used outside of op_helper.c context.
LM32, s390x, UniCore32: remove unused cpu_halted(), regs_to_env() and
env_to_regs().
ARM: make raise_exception() static.
Convert
#include "exec.h"
to
#include "cpu.h"
#include "dyngen-exec.h"
and remove now unused target-*/exec.h.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
cea5f9a28f exposed bugs in unassigned memory
access handling. Fix them by always passing CPUState to the handlers.
Reported-by: Hervé Poussineau <hpoussin@reactos.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Move functions cpu_has_work() and cpu_pc_from_tb() from exec.h to cpu.h. This is
needed by later patches.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Before the next patch, fix coding style of the areas affected.
Change the type of the return value from cpu_has_work() and
qemu_cpu_has_work() to bool.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
