There are one use apiece for these. There is no longer a need for
preserving branch offset operands, as we no longer re-translate.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Also, assert that we don't overflow any of two different offsets into
the TB. Both unwind and goto_tb both record a uint16_t for later use.
This fixes an arm-softmmu test case utilizing NEON in which there is
a TB generated that runs to 7800 opcodes, and compiles to 96k on an
x86_64 host. This overflows the 16-bit offset in which we record the
goto_tb reset offset. Because of that overflow, we install a jump
destination that goes to neverland. Boom.
With this reduced op count, the same TB compiles to about 48k for
aarch64, ppc64le, and x86_64 hosts, and neither assertion fires.
Cc: qemu-stable@nongnu.org
Reported-by: "Jason A. Donenfeld" <Jason@zx2c4.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
I found with qemu 2.11.x or newer that I would get an illegal instruction
error running some Intel binaries on my ARM chromebook. On investigation,
I found it was quitting on memory barriers.
qemu instruction:
mb $0x31
was translating as:
0x604050cc: 5bf07ff5 blpl #0x600250a8
After patch it gives:
0x604050cc: f57ff05b dmb ish
In short, I found INSN_DMB_ISH (memory barrier for ARMv7) appeared to be
correct based on online docs, but due to some endian-related shenanigans it
had to be byte-swapped to suit qemu; it appears INSN_DMB_MCR (memory
barrier for ARMv6) also should be byte swapped (and this patch does so).
I have not checked for correctness of aarch64's barrier instruction.
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Henry Wertz <hwertz10@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
The code sequence we were generating was only good for unsigned
comparisons. For signed comparisions, use the sequence from gcc.
Fixes booting of ppc64 firmware, with a patch changing the code
sequence for ppc comparisons.
Tested-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
It's not even clear what the interface REG and VAL32 were supposed to mean.
All uses had REG = 0 and VAL32 was the bitset assigned to the destination.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Move constants before all of the functions.
Move tcg_out_<format> functions before all
of the others. No functional change.
Signed-off-by: Richard Henderson <rth@twiddle.net>
We are not going to use ldrd for loading the comparator
for 32-bit guests, so don't limit cmp_off to 8 bits then.
This eliminates one insn in the tlb load for some guests.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use UBFX to avoid limitation on CPU_TLB_BITS. Since we're dropping
the initial shift, we need to replace the page masking. We can use
MOVW+BIC to do this without shifting. The result is the same size
as the armv6 path with one less conditional instruction.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Dispense with TCGBackendData, as it has never been used for more than
holding a single pointer. Use a define in the cpu/tcg-target.h to
signal requirement for TCGLabelQemuLdst, so that we can drop the no-op
tcg-be-null.h stubs. Rename tcg-be-ldst.h to tcg-ldst.inc.c.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Replace the USE_DIRECT_JUMP ifdef with a TCG_TARGET_HAS_direct_jump
boolean test. Replace the tb_set_jmp_target1 ifdef with an unconditional
function tb_target_set_jmp_target.
While we're touching all backends, add a parameter for tb->tc_ptr;
we're going to need it shortly for some backends.
Move tb_set_jmp_target and tb_add_jump from exec-all.h to cpu-exec.c.
This opens the possibility for TCG_TARGET_HAS_direct_jump to be
a runtime decision -- based on host cpu capabilities, the size of
code_gen_buffer, or a future debugging switch.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Patch 85aa80813d changed the IF emitting the TST instruction,
but failed to change the ?: converting CMP to CMPEQ, so the
result of the TST is ignored.
Signed-off-by: Richard Henderson <rth@twiddle.net>
The new placement of the TB means that we can use one insn
to load the goto_tb destination directly from the TB.
Signed-off-by: Richard Henderson <rth@twiddle.net>
In theory this would re-enable usage of QEMU on an armv4 host.
Whether this is worthwhile is debatable -- we've been unconditionally
issuing the armv5t BX instruction in the prologue since 2011 without
complaint. Possibly we should simply require an armv6 host.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Instead of exporting goto_ptr directly to TCG frontends, export
tcg_gen_lookup_and_goto_ptr(), which calls goto_ptr with the pointer
returned by the lookup_tb_ptr() helper. This is the only use case
we have for goto_ptr and lookup_tb_ptr, so having this function is
very convenient. Furthermore, it trivially allows us to avoid calling
the lookup helper if goto_ptr is not implemented by the backend.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Message-Id: <1493263764-18657-2-git-send-email-cota@braap.org>
Message-Id: <1493263764-18657-3-git-send-email-cota@braap.org>
Message-Id: <1493263764-18657-4-git-send-email-cota@braap.org>
Message-Id: <1493263764-18657-5-git-send-email-cota@braap.org>
[rth: Squashed 4 related commits.]
Signed-off-by: Richard Henderson <rth@twiddle.net>
We already require gcc 4.1 or newer (for the atomic
support), so the fallback codepaths for older gcc
versions than that are now dead code and we can
just delete them.
NB: clang reports itself as gcc 4.2 (regardless of
clang version), so clang won't be using the fallbacks
either.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
The number of actual invocations of ctpop itself does not warrent
an opcode, but it is very helpful for POWER7 to use in generating
an expansion for ctz.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This will let us choose how to interpret a given constraint
depending on whether the opcode is 32- or 64-bit. Which will
let us share more constraint combinations between opcodes.
At the same time, change the interface to return the advanced
pointer instead of passing it in/out by reference.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This will allow the target to tailor the constraints to the
auto-detected ISA extensions.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This allows us to use this detection within the TCG_TARGET_HAS_*
macros, instead of requiring a function call into tcg-target.inc.c.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Adds tcg_gen_extract_* and tcg_gen_sextract_* for extraction of
fixed position bitfields, much like we already have for deposit.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Previously we allowed fully unaligned operations, but not operations
that are aligned but with less alignment than the operation size.
In addition, arm32, ia64, mips, and sparc had been omitted from the
previous overalignment patch, which would have led to that alignment
being enforced.
Signed-off-by: Richard Henderson <rth@twiddle.net>
These use guard symbols like TCG_TARGET_$target.
scripts/clean-header-guards.pl doesn't like them because they don't
match their file name (they should, to make guard collisions less
likely).
Clean them up: use guard symbol $target_TCG_TARGET_H for
tcg/$target/tcg-target.h.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
While we can store constants via constrants on INDEX_op_st_i32 et al,
we weren't able to spill constants to backing store.
Add a new backend interface, tcg_out_sti, which may store the constant
(and is allowed to fail). Rearrange the temp_* helpers so that we only
attempt to directly store a constant when the temp is becoming dead/free.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Briefly describe in a comment how direct block chaining is done. It
should help in understanding of the following data fields.
Rename some fields in TranslationBlock and TCGContext structures to
better reflect their purpose (dropping excessive 'tb_' prefix in
TranslationBlock but keeping it in TCGContext):
tb_next_offset => jmp_reset_offset
tb_jmp_offset => jmp_insn_offset
tb_next => jmp_target_addr
jmp_next => jmp_list_next
jmp_first => jmp_list_first
Avoid using a magic constant as an invalid offset which is used to
indicate that there's no n-th jump generated.
Signed-off-by: Sergey Fedorov <serge.fdrv@gmail.com>
Signed-off-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Ensure direct jump patching in ARM is atomic by using
atomic_read()/atomic_set() for code patching.
Signed-off-by: Sergey Fedorov <serge.fdrv@gmail.com>
Signed-off-by: Sergey Fedorov <sergey.fedorov@linaro.org>
Message-Id: <1461341333-19646-8-git-send-email-sergey.fedorov@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Check for CONFIG_DEBUG_TCG instead of NDEBUG, drop now useless code.
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: 1461228530-14852-2-git-send-email-aurelien@aurel32.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The TCG code is quite performance sensitive, but at the same time can
also be quite tricky. That is why asserts that can be enabled with the
--enable-debug-tcg configure option.
This used to work the following way:
| #include "config.h"
|
| ...
|
| #if !defined(CONFIG_DEBUG_TCG) && !defined(NDEBUG)
| /* define it to suppress various consistency checks (faster) */
| #define NDEBUG
| #endif
|
| ...
|
| #include <assert.h>
Since commit 757e725b (tcg: Clean up includes) "config.h" as been
replaced by "qemu/osdep.h" which itself includes <assert.h>. As a
consequence the assertions are always enabled, even when using
--disable-debug-tcg, causing a performance regression, especially on
targets with many registers. For instance on qemu-system-ppc the
speed difference is about 15%.
tcg_debug_assert is controlled directly by CONFIG_DEBUG_TCG and already
uses in some places. This patch replaces all the calls to assert into
calss to tcg_debug_assert.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Message-id: 1461228530-14852-1-git-send-email-aurelien@aurel32.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Commit 757e725b58 added a number of #include "qemu/osdep.h"
files to the tcg-target.c files (as they were named at the time).
These are unnecessary because these files are not standalone C
files, and the tcg/tcg.c file which includes them will have
already included osdep.h on their behalf. Remove the unneeded
include directives.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1456238983-10160-4-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Rename the per-architecture tcg-target.c files to tcg-target.inc.c.
This makes it clearer that they are not intended to be standalone
C files, but are instead #included into another source file.
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1456238983-10160-2-git-send-email-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1453832250-766-16-git-send-email-peter.maydell@linaro.org
As we have removed CONFIG_USE_GUEST_BASE, we always use a guest base
and the macros GUEST_BASE and RESERVED_VA become useless: replace
them by their values.
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Message-Id: <1440420834-8388-1-git-send-email-laurent@vivier.eu>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The addition of MO_AMASK means that places that used inverted masks
need to be changed to use positive masks, and places that failed to
mask the intended bits need updating.
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
Tested-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This will be used to size the TLB when more than 8 MMU modes are
used by the target. Limitations come from the limited size of
the immediate fields (which sometimes, as in the case of Aarch64,
extend to instructions that shift the immediate).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1424436345-37924-2-git-send-email-pbonzini@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
The extra information is not yet used but it is now available.
This requires minor changes through all of the tcg backends.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
At the tcg opcode level, not at the tcg-op.h generator level.
This requires minor changes through all of the tcg backends,
but none of the cpu translators.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This is less about improved type checking than enabling a
subsequent change to the representation of labels.
Acked-by: Claudio Fontana <claudio.fontana@huawei.com>
Tested-by: Claudio Fontana <claudio.fontana@huawei.com>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Since all backends have been converted, remove the compatibility code.
Acked-by: Claudio Fontana <claudio.fontana@huawei.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The INDEX_op_call case has just been obsoleted; the mov and movi
cases have not been reachable for years. Attempt to document this
both in each tcg_out_op switch, and via TCG_OPF_NOT_PRESENT.
Because of the TCG_OPF_NOT_PRESENT change, this must be done for
all targets in a single commit.
Signed-off-by: Richard Henderson <rth@twiddle.net>
And use tcg pointer differencing functions as appropriate.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Instead require either mulu2_i32 or muluh_i32. The code in tcg-op.h
already supports looking for both. Previous incomplete conversion?
Signed-off-by: Richard Henderson <rth@twiddle.net>
Most 64-bit targets need to be able to ignore the high bits
of a TCG_TYPE_I32 value.
Suggested-by: Stuart Brady <sdb@zubnet.me.uk>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Static code analyzers complain about signed bitfields with only a single
bit. is_ld is used as a boolean value, so make it bool.
ppc64 already used bool for the 2nd argument is_ld of the local function
add_qemu_ldst_label. Modify all other TCG targets to do follow this
example.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The arm ldrd/strd insns must cause alignment traps, whereas
at least for armv7 ldr/str must handle unaligned operations.
While this is hardly the only problem facing user-only emu,
this solves one problem for i386 on armv7 emulation.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reported-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
It's this that should be subtracted from 0x20 when converting to a right rotate.
Cc: qemu-stable@nongnu.org
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Allow host detection on linux systems without glibc 2.16 or later.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
If we pull the code to emit the actual load/store into a subroutine,
we can share the reg+reg addressing mode code between softmmu and
usermode. This lets us load GUEST_BASE into a temporary register
rather than attempting to add it piece-wise to the address.
Which lets us use movw+movt for armv7, rather than (up to) 4 adds.
Code size for pre-armv7 stays the same.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Step two in the transition, adding the new ldst opcodes. Keep the old
opcodes around until all backends support the new opcodes.
Signed-off-by: Richard Henderson <rth@twiddle.net>
There are free scheduling slots between the sequence of
comparison instructions. This requires changing the
register in use to avoid conflict with those compares.
Signed-off-by: Richard Henderson <rth@twiddle.net>
The main intent of the patch is to allow the tlb addend register
to be changed, without tying that change to the constraint. But
the most common side-effect seems to be to enable usage of ldrd
with the r0,r1 pair.
Signed-off-by: Richard Henderson <rth@twiddle.net>
This allows us to make more intelligent decisions about the relative
offsets of the tlb comparator and the addend, avoiding any need of
writeback addressing.
Signed-off-by: Richard Henderson <rth@twiddle.net>
One of the two constraints we already checked via #if, but
the tlb offset distance was only checked at runtime.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use the new helper_ret_*_mmu routines. Use a conditional call
to arrange for a tail-call from the store path, and to load the
return address for the helper for the load path.
Signed-off-by: Richard Henderson <rth@twiddle.net>
The _cmmu helpers can be moved to exec-all.h. The helpers that are
used from TCG will shortly need access to tcg_target_long so move
their declarations into tcg.h.
This requires minor include adjustments to all TCG backends.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use them in places where mulu2 and muls2 are used.
Optimize mulx2 with dead low part to mulxh.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
With this we can generate armv7 insns even when the OS compiles for a
lower common denominator. The macros are arranged so that when we do
compile for a given ISA, all of the runtime checks for that ISA are
optimized away.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
GCC 4.8 defines a handy __ARM_ARCH symbol that we can use, which
will make us nicely forward compatible with ARMv8 AArch32.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
As it really controls the availability of a thumb interworking
instruction on armv5t.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We can now detect and use divide instructions at runtime, rather than
having to restrict their availability to compile-time.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
There are several hosts with only a "div" insn. Remainder is computed
manually from the quotient and inputs. We can do this generically.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We've got a compile-time check for the condition in exec/cpu-defs.h.
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: liguang <lig.fnst@cn.fujitsu.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Avoid the mini constant pool for armv7, and avoid replicating
the test for pre-v7.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Found by inspection, since the effect of the bug was simply to
send all memory ops through the slow path.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Move the slow path out of line, as the TODO's mention.
This allows the fast path to be unconditional, which can
speed up the fast path as well, depending on the core.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Work better with branch predition when we have movw+movt,
as the size of the code is the same. Perhaps re-evaluate
when we have a proper constant pool.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
The schedule was fully serial, with no possibility for dual issue.
The old schedule had a minimal issue of 7 cycles; the new schedule
has a minimal issue of 5 cycles.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Share code between qemu_ld and qemu_st to process the tlb.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Use even more primitive helper functions to avoid lots of duplicated code.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Make the code more readable by only having one copy of the magic
numbers, swapping registers as needed prior to that. Speed the
compiler by not applying the rd == rn avoidance for v6 or later.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
R12 is call clobbered, while R8 is call saved. This change
gives tcg one more call saved register for real data.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We get to re-use the _rIN and _rIK subroutines to handle the various
combinations of add vs sub. Fold the << 21 into the opcode enum values
so that we can explicitly add TO_CPSR as desired.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This greatly improves code generation for addition of small
negative constants.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
This greatly improves the code we can produce for deposit
without armv7 support.
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Richard Henderson <rth@twiddle.net>
We were not allocating TCG_STATIC_CALL_ARGS_SIZE, so this meant that
any helper with more than 4 arguments would clobber the saved regs.
Realizing that we're supposed to have this memory pre-allocated means
we can clean up the tcg_out_arg functions, which were trying to do
more stack allocation.
Allocate stack memory for the TCG temporaries while we're at it.
Signed-off-by: Richard Henderson <rth@twiddle.net>
We even had the encoding of smull already handy...
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Silence a (legitimate) complaint about missing parentheses:
tcg/arm/tcg-target.c: In function ‘tcg_out_qemu_ld’:
tcg/arm/tcg-target.c:1148:5: error: suggest parentheses around
comparison in operand of ‘&’ [-Werror=parentheses]
tcg/arm/tcg-target.c: In function ‘tcg_out_qemu_st’:
tcg/arm/tcg-target.c:1357:5: error: suggest parentheses around
comparison in operand of ‘&’ [-Werror=parentheses]
which meant that we would mistakenly always assert if running
a QEMU built with debug enabled on ARM.
Signed-off-by: Peter Maydell <peter.maydelL@linaro.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
The bswap16 TCG opcode assumes that the high bytes of the temp equal
to 0 before calling it. The ARM backend implementation takes this
assumption to slightly optimize the generated code.
The same implementation is called for implementing the cross-endian
qemu_st16 opcode, where this assumption is not true anymore. One way to
fix that would be to zero the high bytes before calling it. Given the
store instruction just ignore them, it is possible to provide a slightly
more optimized version. With ARMv6+ the rev16 instruction does the work
correctly. For lower ARM versions the patch provides a version which
behaves correctly with non-zero high bytes, but fill them with junk.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-stable@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The TCG arm backend considers likely that the offset to the TLB
entries does not exceed 12 bits for mem_index = 0. In practice this is
not true for at least the MIPS target.
The current patch fixes that by loading the bits 23-12 with a separate
instruction, and using loads with address writeback, independently of
the value of mem_idx. In total this allow a 24-bit offset, which is a
lot more than needed.
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: qemu-stable@nongnu.org
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Implement movcond_i32 for ARM, as the sequence
mov dst, v2 (implicitly done by the tcg common code)
cmp c1, c2
movCC dst, v1
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The code to emit either an immediate cmp or a register cmp insn is
duplicated in several places; factor it out into its own function.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
GUEST_BASE support is now supported by all TCG backends, and is
now mandatory. Drop the now-pointless TCG_TARGET_HAS_GUEST_BASE
define (set by every backend) and the error if it is unset.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
* 'trivial-patches' of git://github.com/stefanha/qemu:
versatilepb: Use symbolic indices for ARM PIC
qdev: kill bogus comment
qemu-barrier: Fix compiler version check for future gcc versions
hw: Add missing 'static' attribute for QEMUMachine
cleanup useless return sentence
qemu-sockets: Fix compiler warning (regression for MinGW)
vnc: Fix spelling (hellmen -> hellman) in comment
slirp: Fix spelling in comment (enought -> enough, insure -> ensure)
tcg/arm: Use tcg_out_mov_reg rather than inline equivalent code
cpu: Add missing 'static' attribute to qemu_global_mutex
configure: Support empty target list (--target-list=)
hw: Fix return value check for bdrv_read, bdrv_write
There are several cases that can be handled easier inside both
translators and code generators if we have out-of-band values
for conditions. It's easy enough to handle ALWAYS and NEVER in
the natural way inside the tcg middle-end.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The TCG jmp operation doesn't really make sense in the QEMU context, it
is unused, it is not implemented by some targets, and it is wrongly
implemented by some others.
This patch simply removes it.
Reviewed-by: Richard Henderson <rth@twiddle.net>
Acked-by: Blue Swirl <blauwirbel@gmail.com>
Acked-by: Stefan Weil<sw@weilnetz.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use the recently introduced tcg_out_mov_reg() function rather than
the equivalent inline code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Stefan Hajnoczi <stefanha@gmail.com>
The TCG targets no longer need individual implementations.
Since commit 6a18ae2d29,
'flags' is no longer used in tcg_target_get_call_iarg_regs_count.
The remaining tcg_target_get_call_iarg_regs_count is trivial and only
called once. Therefore the patch eliminates it completely.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Implemented with setcond if the target does not provide
the optional opcode.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that CONFIG_TCG_PASS_AREG0 is enabled for all targets,
remove dead code and support for !CONFIG_TCG_PASS_AREG0 case.
Remove dyngen-exec.h and all references to it. Although included by
hw/spapr_hcall.c, it does not seem to use it.
Remove unused HELPER_CFLAGS.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The CONFIG_TCG_PASS_AREG0 code for calling ld/st helpers was
broken in that it did not respect the ABI requirement that 64
bit values were passed in even-odd register pairs. The simplest
way to fix this is to implement some new utility functions
for marshalling function arguments into the correct registers
and stack, so that the code which sets up the address and
data arguments does not need to care whether there has been
a preceding env argument.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Optionally, make memory access helpers take a parameter for CPUState
instead of relying on global env.
On most targets, perform simple moves to reorder registers. On i386,
switch from regparm(3) calling convention to standard stack-based
version.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Scripted conversion:
for file in *.[hc] hw/*.[hc] hw/kvm/*.[hc] linux-user/*.[hc] linux-user/m68k/*.[hc] bsd-user/*.[hc] darwin-user/*.[hc] tcg/*/*.[hc] target-*/cpu.h; do
sed -i "s/CPUState/CPUArchState/g" $file
done
All occurrences of CPUArchState are expected to be replaced by QOM CPUState,
once all targets are QOM'ified and common fields have been extracted.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
The TCG targets i386 and tci needed a change of the function
prototype for w64.
This change is currently not needed for the other TCG targets,
but it can be applied to avoid code differences.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
ARM still doesn't support 16GB buffers in 32-bit modes, replace the
16GB by 16MB in the comment.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
On ARM, in Thumb mode r7 is used for the framepointer; this meant
that we would fail to compile in debug mode because we were using r7
for TCG_AREG0. Shift to r6 instead to avoid this clash.
(Bug reported as LP:870990.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
On ARM, don't map the code buffer at a fixed location, and fix up the
call/goto tcg routines to let it do long jumps.
Mapping the code buffer at a fixed address could sometimes result in it being
mapped over the top of the heap with pretty random results.
Signed-off-by: Dr. David Alan Gilbert <david.gilbert@linaro.org>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Including tcg_out_ld, tcg_out_st, tcg_out_mov, tcg_out_movi.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Most targets did not name the enum; tci used TCGRegister.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Remove the unused function tcg_out_addi() from the ARM TCG backend;
this fixes a compilation failure on ARM hosts with newer gcc.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
It is now declared for all tcg targets in tcg.h,
so the tcg target specific declarations are redundant.
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
By always defining these symbols, we can eliminate a lot of ifdefs.
To allow this to be checked reliably, the semantics of the
TCG_TARGET_HAS_* macros must be changed from def/undef to true/false.
This allows even more ifdefs to be removed, converting them into
C if statements.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Make functions take a parameter for CPUState instead of relying
on global env. Pass CPUState pointer to TCG prologue, which moves
it to AREG0.
Thanks to Peter Maydell and Laurent Desnogues for the ARM prologue
change.
Revert the hacks to avoid AREG0 use on Sparc hosts.
Move cpu_has_work() and cpu_pc_from_tb() from exec.h to cpu.h.
Compile the file without HELPER_CFLAGS.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Although the TCG generated code is always in ARM mode, it is possible
that the host code was compiled by gcc in Thumb mode (this is often the
default for Linux distributions targeting ARM v7 only). Handle this
by using BLX imm when doing a call from ARM into Thumb mode.
Since BLX imm is not a conditionalisable instruction, we make
tcg_out_call() no longer take a condition code; we were only ever
using it with COND_AL anyway.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Add a comment about cache coherency and retranslation, so that people
developping new targets based on existing ones are warned of the issue.
Acked-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Improve constant loading in two ways:
- On all ARM versions, it's possible to load 0xffffff00 = -0x100 using
the mvn rd, #0. Fix the conditions.
- On <= ARMv6 versions, where movw and movt are not available, load the
constants using mov and orr with rotations depending on the constant
to load. This is very useful for example to load constants where the
low byte is 0. This reduce the generated code size by about 7%.
Also fix the coding style at the same time.
Cc: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Due to a typo, qemu_st64 doesn't properly byteswap the 32-bit low word of
a 64 bit word before saving it. This patch fixes that.
Acked-by: Andrzej Zaborowski <balrogg@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
QEMU uses code retranslation to restore the CPU state when an exception
happens. For it to work the retranslation must not modify the generated
code. This is what is currently implemented in ARM TCG.
However on CPU that don't have icache/dcache/memory synchronised like
ARM, this requirement is stronger and code retranslation must not modify
the generated code "atomically", as the cache line might be flushed
at any moment (interrupt, exception, task switching), even if not
triggered by QEMU. The probability for this to happen is very low, and
depends on cache size and associativiy, machine load, interrupts, so the
symptoms are might happen randomly.
This requirement is currently not followed in tcg/arm, for the
load/store code, which basically has the following structure:
1) tlb access code is written
2) conditional fast path code is written
3) branch is written with a temporary target
4) slow path code is written
5) branch target is updated
The cache lines corresponding to the retranslated code is not flushed
after code retranslation as the generated code is supposed to be the
same. However if the cache line corresponding to the branch instruction
is flushed between step 3 and 5, and is not flushed again before the
code is executed again, the branch target is wrong. In the guest, the
symptoms are MMU page fault at a random addresses, which leads to
kernel page fault or segmentation faults.
The patch fixes this issue by avoiding writing the branch target until
it is known, that is by writing only the branch instruction first, and
later only the offset.
This fixes booting linux guests on ARM hosts (tested: arm, i386, mips,
mipsel, sh4, sparc).
Acked-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Both tcg_target_init and tcg_target_qemu_prologue
are unused outside of tcg.c.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Mirror tcg_out_movi in having a TYPE parameter. This allows x86_64
to perform the move at the proper width, which may elide a REX prefix.
Introduce a TCG_TYPE_REG enumerator to represent the "native width"
of the host register, and to distinguish the usage from "pointer data"
as represented by the existing TCG_TYPE_PTR.
Update all targets to match.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The beginning of the register allocation order list on the TCG arm
target matches the list of clobbered registers. This means that when an
helper is called, there is almost always clobbered registers that have
to be spilled.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
64-bit arguments should be aligned on an even register as specified
by the "Procedure Call Standard for the ARM Architecture".
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
addr_reg, data_reg and data_reg2 can't be register r0 or r1 du to the
constraints. Don't check if they equals these registers.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
On big endian targets, data arguments of qemu_ld/st ops have to be
byte swapped. Two temporary registers are needed for qemu_st to do
the bswap. r0 and r1 are used in system mode, do the same in user
mode, which implies reworking the constraints.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
While it make sense to pass a conditional argument to tcg_out_*()
functions as the ARM architecture allows that, it doesn't make sense
for qemu_ld/st functions. These functions use comparison instructions
and conditional execution already, so it is not possible to use a
second level of conditional execution.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add an bswap16 and bswap32 ops, either using the rev and rev16
instructions on ARMv6+ or shifts and logical operations on previous
ARM versions. In both cases the result use less instructions than
the pure TCG version.
These ops are also needed by the qemu_ld/st functions.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add an ext16u op, either using the uxth instruction on ARMv6+ or two
shifts on previous ARM versions. In both cases the result use the same
number or less instructions than the pure TCG version.
Also move all sign extension code to separate functions, so that they
can be reused in other parts of the code.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Use a set of variables to define the allowed ARM instructions, depending
on the __ARM_ARCH_*__ GCC defines.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The TCG ARM backends uses integer values to refer to both immediate
values and register number. This makes the code difficult to read.
The patch below replaces all (if I haven't miss any ;-) integer values
representing register number by TCG_REG_* enum values.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Instead of writing very compact code, declare all registers that are
clobbered or reserved one by one. This makes the code easier to read.
Also declare all the 16 registers to TCG, and mark pc as reserved.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There is no need to save the LR register (r14) before a call to a
subroutine. According to the "Procedure Call Standard for the ARM
Architecture", it is the job of the callee to save this register.
Moreover, this register is already saved in the prologue/epilogue.
This patch removes the disabled SAVE_LR code, as there is no need to
reenable later.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Commit 86feb1c860
did not change all occurrences of INDEX_op_qemu_ld32u
for tcg/arm.
Please note that I could not test this patch
(I have currently no arm system available).
Cc: Richard Henderson <rth@twiddle.net>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Some targets (e.g. Alpha and MIPS64) need to keep 32-bit operands
sign-extended in 64-bit registers (regardless of the "real" sign
of the operand). For that, we need to be able to distinguish
between a 32-bit load with a 32-bit result and a 32-bit load with
a given extension to a 64-bit result. This distinction already
exists for the ld* loads, but not the qemu_ld* loads.
Reserve qemu_ld32u for 64-bit outputs and introduce qemu_ld32 for
32-bit outputs. Adjust all code generators to match.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Give the enumeration formed from tcg-opc.h a name: TCGOpcode.
Use that enumeration type instead of "int" whereever appropriate.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There is no need to save r7, it is used to store the address
of the env structure and is not modified by GCC.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Some targets like ARM would benefit to use 32-bit helpers for
div/rem/divu/remu.
Create a #define for div2 so that targets can select between
div, div2 and helper implementation. Use the helper version if none
of the #define are present.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Since commit 6113d6d316 QEMU crashes
on ARM hosts. This is not a bug of this commit, but a latent bug
revealed by this commit.
The TCG code is called through a procedure call using the prologue
and epilogue code. This code does not save and restore enough registers.
The "Procedure Call Standard for the ARM Architecture" says:
A subroutine must preserve the contents of the registers r4-r8, r10,
r11 and SP (and r9 in PCS variants that designate r9 as v6).
The current code only saves and restores r9 to r11, and misses r4 to
r8. The patch fixes that by saving r4 to r12. Theoretically there is
no need to save and restore r12, but an even number of registers have
to be saved as per EABI.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
When restoring register values, increase the stack register for skipped
values.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
This patch uses sxtb for ext8s_i32 and sxth for ext16s_i32 in ARM back-end.
Signed-off-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
the encode_imm function in tcg/arm/tcg-target.c lacks shift declaration.
Laurent
Signed-off-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
this patch handles all possible constants for immediate operand of ALU ops.
I'm not very satisfied by the implementation.
Laurent
Signed-off-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
- use movw/movt to load immediate values for ARMv7-A
- implement add/sub/and/or/xor with immediate (only 8-bit)
Laurent
Signed-off-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Signed-off-by: Andrzej Zaborowski <andrew.zaborowski@intel.com>
Re-implement GUEST_BASE support.
Offset guest ddress space by default if the guest binary contains
regions below the host mmap_min_addr.
Implement support for i386, x86-64 and arm hosts.
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Paul Brook <paul@codesourcery.com>
Rename bswap_i32 into bswap32_i32 and bswap_i64 into bswap64_i64
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
git-svn-id: svn://svn.savannah.nongnu.org/qemu/trunk@6829 c046a42c-6fe2-441c-8c8c-71466251a162
