The Allwinner H3 System on Chip contains multiple USB 2.0 bus
connections which provide software access using the Enhanced
Host Controller Interface (EHCI) and Open Host Controller
Interface (OHCI) interfaces. This commit adds support for
both interfaces in the Allwinner H3 System on Chip.
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200311221854.30370-5-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Clock Control Unit is responsible for clock signal generation,
configuration and distribution in the Allwinner H3 System on Chip.
This commit adds support for the Clock Control Unit which emulates
a simple read/write register interface.
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200311221854.30370-4-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Allwinner H3 is a System on Chip containing four ARM Cortex A7
processor cores. Features and specifications include DDR2/DDR3 memory,
SD/MMC storage cards, 10/100/1000Mbit Ethernet, USB 2.0, HDMI and
various I/O modules. This commit adds support for the Allwinner H3
System on Chip.
Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200311221854.30370-2-nieklinnenbank@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
i.MX25 supports two USB controllers. Let's wire them up.
With this patch, imx25-pdk can boot from both USB ports.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200310215146.19688-3-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Wire up eSDHC controllers in fsl-imx25. For imx25-pdk, connect drives
provided on the command line to available eSDHC controllers.
This patch enables booting the imx25-pdk emulation from SD card.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200310215146.19688-2-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: made commit subject consistent with other patch]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the Versal LPD ADMAs.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds the "virtio,pci-iommu" node in the host bridge node and
the RID mapping, excluding the IOMMU RID.
This is done in the virtio-iommu-pci hotplug handler which
gets called only if no firmware is loaded or if -no-acpi is
passed on the command line. As non DT integration is
not yet supported by the kernel we must make sure we
are in DT mode. This limitation will be removed as soon
as the topology description feature gets supported.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20200214132745.23392-10-eric.auger@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Instantiate EHCI and OHCI controllers on Allwinner A10. OHCI ports are
modeled as companions of the respective EHCI ports.
With this patch applied, USB controllers are discovered and instantiated
when booting the cubieboard machine with a recent Linux kernel.
ehci-platform 1c14000.usb: EHCI Host Controller
ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
ehci-platform 1c14000.usb: irq 26, io mem 0x01c14000
ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
ehci-platform 1c1c000.usb: EHCI Host Controller
ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
ehci-platform 1c1c000.usb: irq 31, io mem 0x01c1c000
ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
ohci-platform 1c14400.usb: Generic Platform OHCI controller
ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3
ohci-platform 1c14400.usb: irq 27, io mem 0x01c14400
ohci-platform 1c1c400.usb: Generic Platform OHCI controller
ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4
ohci-platform 1c1c400.usb: irq 32, io mem 0x01c1c400
usb 2-1: new high-speed USB device number 2 using ehci-platform
usb-storage 2-1:1.0: USB Mass Storage device detected
scsi host1: usb-storage 2-1:1.0
usb 3-1: new full-speed USB device number 2 using ohci-platform
input: QEMU QEMU USB Mouse as /devices/platform/soc/1c14400.usb/usb3/3-1/3-1:1.0/0003:0627:0001.0001/input/input0
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
Message-id: 20200217204812.9857-4-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initialize EHCI controllers on AST2400 and AST2500 using the existing
TYPE_PLATFORM_EHCI. After this change, booting ast2500-evb into Linux
successfully instantiates a USB interface.
ehci-platform 1e6a3000.usb: EHCI Host Controller
ehci-platform 1e6a3000.usb: new USB bus registered, assigned bus number 1
ehci-platform 1e6a3000.usb: irq 21, io mem 0x1e6a3000
ehci-platform 1e6a3000.usb: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.05
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200206183437.3979-1-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
kvm-no-adjvtime is a KVM specific CPU property and a first of its
kind. To accommodate it we also add kvm_arm_add_vcpu_properties()
and a KVM specific CPU properties description to the CPU features
document.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20200120101023.16030-7-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The overhead for the OpenBMC firmware images using the a custom U-Boot
is around 2 seconds, which is fine, but with a U-Boot from mainline,
it takes an extra 50 seconds or so to reach Linux. A quick survey on
the number of reads performed on the flash memory region gives the
following figures :
OpenBMC U-Boot 922478 (~ 3.5 MBytes)
Mainline U-Boot 20569977 (~ 80 MBytes)
QEMU must be trashing the TCG TBs and reloading text very often. Some
addresses are read more than 250.000 times. Until we find a solution
to improve boot time, execution from MMIO is not activated by default.
Setting this option also breaks migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20200114103433.30534-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initialise another SDHCI model instance for the AST2600's eMMC
controller and use the SDHCI's num_slots value introduced previously to
determine whether we should create an SD card instance for the new slot.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20200114103433.30534-3-clg@kaod.org
[ clg : - removed ternary operator from sdhci_attach_drive()
- renamed SDHCI objects with a '-controller' prefix ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
First parameter to exynos4210_get_irq() is not the SPI port number,
but the interrupt group number. Interrupt groups are 20 for mdma
and 21 for pdma. Interrupts are not inverted. Controllers support 32
events (pdma) or 31 events (mdma). Events must all be routed to a single
interrupt line. Set other parameters as documented in Exynos4210 datasheet,
section 8 (DMA controller).
Fixes: 59520dc65e ("hw/arm/exynos4210: Add DMA support for the Exynos4210")
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 20200123052540.6132-4-linux@roeck-us.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an emulation for the RNGC random number generator and the compatible
RNGB variant. These peripherals are included (at least) in imx25 and
imx35 chipsets.
The emulation supports the initial self test, reseeding the prng and
reading random numbers.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By calling qdev_pass_gpios() we don't need to hold a copy of the
IRQs from the INTC into the SoC state.
Instead of filling an array of qemu_irq and passing it around, we
can now directly call qdev_get_gpio_in() on the SoC.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20191230110953.25496-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
These definitions are specific to the A10 SoC and don't need
to be exported to the different Allwinner peripherals.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20191230110953.25496-4-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Since clocks are not QOM objects, replace PROP_PTR of clocks with
setters methods.
Move/adapt the existing TODO comment about a clock framework.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Since clocks are not QOM objects, replace PROP_PTR of clocks with
setters methods.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Since clocks are not QOM objects, replace PROP_PTR of clocks with
setters methods.
(in theory there should probably be different methods for omap1 &
omap2 intc, but this is left as a future improvement)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Make the gic a field in the machine state, and instead of filling
an array of qemu_irq and passing it around, directly call
qdev_get_gpio_in() on the gic field.
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20191209090306.20433-1-philmd@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
AspeedBoardConfig is a redundant way to define class attributes and it
complexifies the machine definition and initialization.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-14-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Currently, we link the DRAM memory region to the FMC model (for DMAs)
through a property alias at the SoC level. The I2C model will need a
similar region for DMA support, add a DRAM region property at the SoC
level for both model to use.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20191119141211.25716-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add the CRP as unimplemented thus avoiding bus errors when
guests access these registers.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20191115154734.26449-2-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The boot.c code usually puts the CPU into NS mode directly when it is
booting a kernel. Since fc1120a7f5 this has included a
requirement to set NSACR to give NS state access to the FPU; we fixed
that for the usual code path in ece628fcf6. However, it is also
possible for a board model to request an alternative mode of booting,
where its 'board_setup' code hook runs in Secure state and is
responsible for doing the S->NS transition after it has done whatever
work it must do in Secure state. In this situation the board_setup
code now also needs to update NSACR.
This affects all boards which set info->secure_board_setup, which is
currently the 'raspi' and 'highbank' families. They both use the
common arm_write_secure_board_setup_dummy_smc().
Set the NSACR CP11 and CP10 bits in the code written by that
function, to allow FPU access in Non-Secure state when using dummy
SMC setup routine. Otherwise an AArch32 kernel booted on the
highbank or raspi boards will UNDEF as soon as it tries to use the
FPU.
Update the comment describing secure_board_setup to note the new
requirements on users of it.
This fixes a kernel panic when booting raspbian on raspi2.
Successfully tested with:
2017-01-11-raspbian-jessie-lite.img
2018-11-13-raspbian-stretch-lite.img
2019-07-10-raspbian-buster-lite.img
Fixes: fc1120a7f5
Signed-off-by: Clement Deschamps <clement.deschamps@greensocs.com>
Tested-by: Laurent Bonnans <laurent.bonnans@here.com>
Message-id: 20191104151137.81931-1-clement.deschamps@greensocs.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: updated comment to boot.h to note new requirement on
users of secure_board_setup; edited/rewrote commit message]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
As we are going to add more core-specific fields, add a 'cpu'
structure and move the ARMCPU field there as 'core'.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191019234715.25750-7-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Connect the recently added SYS_timer.
Now U-Boot does not hang anymore polling a free running counter
stuck at 0.
This timer is also used by the Linux kernel thermal subsystem.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20191019234715.25750-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Map the thermal sensor in the BCM2835 block.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20191019234715.25750-3-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Move RTC devices under the hw/rtc/ subdirectory.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20191003230404.19384-12-philmd@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20191023130455.1347-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SDRAM is incorrectly created in the OMAP310 SoC.
Move its creation in the board code, this will later allow the
board to have the QOM ownership of the RAM.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-6-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SDRAM is incorrectly created in the OMAP2420 SoC.
Move its creation in the board code, this will later allow the
board to have the QOM ownership of the RAM.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20191021190653.9511-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ARM ACPI memory hotplug support +
tests for new arm/virt ACPI tables.
Virtio fs support (no migration).
A vhost-user reconnect bugfix.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJdpjPbAAoJECgfDbjSjVRpQqUH/2xyT++y8K17mCI1IILLZd3d
eOqElEHz78qlEfR2euv63YksZoeHpMO5HiAdwOGGF8CjcaCT4Hl+pPDffTYVXtt+
VZ88vSSXL49wpMcpvRGR5Isy0eXJzWilTBMu2eu8phN9tX82dlu08Oi4XGAosrBJ
uZg61DyiGDnSOpoofHhjvXJEaiL0pzkTjf8qAoW3TaVcB9NQKnunMEIDD646JS5z
AAj4+XBJfUG9cp7/MG+djjVmJDdUpjL5e5uWNWakbgUVqSbHog78RIrBoD6SH7pt
/6hHHoSM9VX1wWgdTdVdNAQAZVnWs31w4v31d8UfaT15KJEoG47U0gDgmLzXDyo=
=+xdg
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/mst/tags/for_upstream' into staging
virtio, vhost, acpi: features, fixes, tests
ARM ACPI memory hotplug support +
tests for new arm/virt ACPI tables.
Virtio fs support (no migration).
A vhost-user reconnect bugfix.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Tue 15 Oct 2019 22:02:19 BST
# gpg: using RSA key 281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
virtio: add vhost-user-fs-pci device
virtio: add vhost-user-fs base device
virtio: Add virtio_fs linux headers
tests/acpi: add expected tables for arm/virt
tests: document how to update acpi tables
tests: Add bios tests to arm/virt
tests: allow empty expected files
tests/acpi: add empty files
tests: Update ACPI tables list for upcoming arm/virt tests
docs/specs: Add ACPI GED documentation
hw/arm: Use GED for system_powerdown event
hw/arm: Factor out powerdown notifier from GPIO
hw/arm/virt-acpi-build: Add PC-DIMM in SRAT
hw/arm/virt: Enable device memory cold/hot plug with ACPI boot
hw/arm/virt: Add memory hotplug framework
hw/acpi: Add ACPI Generic Event Device Support
hw/acpi: Do not create memory hotplug method when handler is not defined
hw/acpi: Make ACPI IO address space configurable
vhost-user: save features if the char dev is closed
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Base addresses and sizes taken from the "BCM2835 ARM Peripherals"
datasheet from February 06 2012:
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190926173428.10713-6-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The UART1 is part of the AUX peripheral,
the PCM_CLOCK (yet unimplemented) is part of the CPRMAN.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190926173428.10713-5-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-24-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 SoC has an extra controller to set the PHY registers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-23-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
To support the ast2600's four MACs allow SoCs to specify the number
they have, and create that many.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-22-clg@kaod.org
[clg: - included a check on sc->macs_num when realizing the macs
- included interrupt definitions for the AST2600 ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initial definitions for a simple machine using an AST2600 SoC (Cortex
CPU).
The Cortex CPU and its interrupt controller are too complex to handle
in the common Aspeed SoC framework. We introduce a new Aspeed SoC
class with instance_init and realize handlers to handle the differences
with the AST2400 and the AST2500 SoCs. This will add extra work to
keep in sync both models with future extensions but it makes the code
clearer.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-19-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
It prepares ground for the AST2600.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190925143248.10000-18-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2600 has four watchdogs, and they each have a 0x40 of registers.
When running as part of an ast2600 system we must check a different
offset for the system reset control register in the SCU.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-12-clg@kaod.org
[clg: - reworked model integration into new object class ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SOCs have two SD/MMC controllers. Add a device that
encapsulates both of these controllers and models the Aspeed-specific
registers and behavior.
Tested by reading from mmcblk0 in Linux:
qemu-system-arm -machine romulus-bmc -nographic \
-drive file=flash-romulus,format=raw,if=mtd \
-device sd-card,drive=sd0 -drive file=_tmp/kernel,format=raw,if=sd,id=sd0
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190925143248.10000-3-clg@kaod.org
[clg: - changed the controller MMIO window size to 0x1000
- moved the MMIO mapping of the SDHCI slots at the SoC level
- merged code to add SD drives on the SD buses at the machine level ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is in preparation of using GED device for
system_powerdown event. Make the powerdown notifier
registration independent of create_gpio() fn.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20190918130633.4872-8-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This initializes the GED device with base memory and irq, configures
ged memory hotplug event and builds the corresponding aml code. With
this, both hot and cold plug of device memory is enabled now for Guest
with ACPI boot. Memory cold plug support with Guest DT boot is not yet
supported.
As DSDT table gets changed by this, update bios-tables-test-allowed-diff.h
to avoid "make check" failure.
Signed-off-by: Shameer Kolothum <shameerali.kolothum.thodi@huawei.com>
Message-Id: <20190918130633.4872-6-shameerali.kolothum.thodi@huawei.com>
Acked-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Improve the naming of the different controller models to ease their
generation when initializing the SoC. The rename of the SMC types is
breaking migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190904070506.1052-5-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In struct arm_boot_info, kernel_filename, initrd_filename and
kernel_cmdline are copied from from MachineState. This patch add
MachineState as a parameter into arm_load_dtb() and move the copy chunk
of kernel_filename, initrd_filename and kernel_cmdline into
arm_load_kernel().
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Liu Jingqi <jingqi.liu@intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Tao Xu <tao3.xu@intel.com>
Message-Id: <20190809065731.9097-2-tao3.xu@intel.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Cédric Le Goater <clg@kaod.org>
[ehabkost: include hw/boards.h again to fix build failures]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
In my "build everything" tree, changing sysemu/sysemu.h triggers a
recompile of some 5400 out of 6600 objects (not counting tests and
objects that don't depend on qemu/osdep.h).
Almost a third of its inclusions are actually superfluous. Delete
them. Downgrade two more to qapi/qapi-types-run-state.h, and move one
from char/serial.h to char/serial.c.
hw/semihosting/config.c, monitor/monitor.c, qdev-monitor.c, and
stubs/semihost.c define variables declared in sysemu/sysemu.h without
including it. The compiler is cool with that, but include it anyway.
This doesn't reduce actual use much, as it's still included into
widely included headers. The next commit will tackle that.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-27-armbru@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Drop unnecessary inclusions from headers. Downgrade a few more to
exec/hwaddr.h.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-17-armbru@redhat.com>
In my "build everything" tree, changing hw/irq.h triggers a recompile
of some 5400 out of 6600 objects (not counting tests and objects that
don't depend on qemu/osdep.h).
hw/hw.h supposedly includes it for convenience. Several other headers
include it just to get qemu_irq and.or qemu_irq_handler.
Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to
qemu/typedefs.h, and then include hw/irq.h only where it's still
needed. Touching it now recompiles only some 500 objects.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-13-armbru@redhat.com>
According to hw/ide/internal's file comment, only files in hw/ide/ are
supposed to include it. Drag reality slightly closer to supposition.
Three includes outside hw/ide remain: hw/arm/sbsa-ref.c,
include/hw/ide/pci.h, and include/hw/misc/macio/macio.h. Turns out
board code needs ide-internal.h to wire up IDE stuff. More cleanup is
needed. Left for another day.
Cc: John Snow <jsnow@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190812052359.30071-11-armbru@redhat.com>
Back in 2016, we discussed[1] rules for headers, and these were
generally liked:
1. Have a carefully curated header that's included everywhere first. We
got that already thanks to Peter: osdep.h.
2. Headers should normally include everything they need beyond osdep.h.
If exceptions are needed for some reason, they must be documented in
the header. If all that's needed from a header is typedefs, put
those into qemu/typedefs.h instead of including the header.
3. Cyclic inclusion is forbidden.
This patch gets include/ closer to obeying 2.
It's actually extracted from my "[RFC] Baby steps towards saner
headers" series[2], which demonstrates a possible path towards
checking 2 automatically. It passes the RFC test there.
[1] Message-ID: <87h9g8j57d.fsf@blackfin.pond.sub.org>
https://lists.nongnu.org/archive/html/qemu-devel/2016-03/msg03345.html
[2] Message-Id: <20190711122827.18970-1-armbru@redhat.com>
https://lists.nongnu.org/archive/html/qemu-devel/2019-07/msg02715.html
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20190812052359.30071-2-armbru@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
The i.MX6UL always has a single Cortex-A7 CPU (we set FSL_IMX6UL_NUM_CPUS
to 1 in line with this). This means that all the code in fsl-imx6ul.c to
handle multiple CPUs is dead code, and Coverity is now complaining that
it is unreachable (CID 1403008, 1403011).
Remove the unreachable code and the only-executes-once loops,
and replace the single-entry cpu[] array in the FSLIMX6ULState
with a simple cpu member.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190712115030.26895-1-peter.maydell@linaro.org
The XDMA engine embedded in the Aspeed SOCs performs PCI DMA operations
between the SOC (acting as a BMC) and a host processor in a server.
The XDMA engine exists on the AST2400, AST2500, and AST2600 SOCs, so
enable it for all of those. Add trace events on the important register
writes in the XDMA engine.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20190618165311.27066-21-clg@kaod.org
[clg: - changed title ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoCs have two MACs. Extend the Aspeed model to support a
second NIC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-7-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The current models of the Aspeed SoCs only have one CPU but future
ones will support SMP. Introduce a new num_cpus field at the SoC class
level to define the number of available CPUs per SoC and also
introduce a 'num-cpus' property to activate the CPUs configured for
the machine.
The max_cpus limit of the machine should depend on the SoC definition
but, unfortunately, these values are not available when the machine
class is initialized. This is the reason why we add a check on
num_cpus in the AspeedSoC realize handler.
SMP support will be activated when models for such SoCs are implemented.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-6-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
All systems have an RTC.
The IRQ is hooked up but the model does not use it at this stage. There
is no guest code that uses it, so this limitation is acceptable.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190618165311.27066-5-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will simplify the definition of new SoCs, like the AST2600 which
should use a slightly different address space and have a different set
of controllers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-3-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This will simplify the definition of new SoCs, like the AST2600 which
should use a different CPU and a different IRQ number layout.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 20190618165311.27066-2-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Datasheet for i.MX7 is incorrect and i.MX7's PCI IRQ mapping matches
that of i.MX6:
* INTD/MSI 122
* INTC 123
* INTB 124
* INTA 125
Fix all of the relevant code to reflect that fact. Needed by latest
Linux kernels.
(Reference: Linux kernel commit 538d6e9d597584e80 from an
NXP employee confirming that the datasheet is incorrect and
with a report of a test against hardware.)
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added ref to kernel commit confirming the datasheet error]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add no-op/unimplemented PCIE PHY IP block. Needed by new kernels to
use PCIE.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SSE-200 hardware has configurable integration settings which
determine whether its two CPUs have the FPU and DSP:
* CPU0_FPU (default 0)
* CPU0_DSP (default 0)
* CPU1_FPU (default 1)
* CPU1_DSP (default 1)
Similarly, the IoTKit has settings for its single CPU:
* CPU0_FPU (default 1)
* CPU0_DSP (default 1)
Of our four boards that use either the IoTKit or the SSE-200:
* mps2-an505, mps2-an521 and musca-a use the default settings
* musca-b1 enables FPU and DSP on both CPUs
Currently QEMU models all these boards using CPUs with
both FPU and DSP enabled. This means that we are incorrect
for mps2-an521 and musca-a, which should not have FPU or DSP
on CPU0.
Create QOM properties on the ARMSSE devices corresponding to the
default h/w integration settings, and make the Musca-B1 board
enable FPU and DSP on both CPUs. This fixes the mps2-an521
and musca-a behaviour, and leaves the musca-b1 and mps2-an505
behaviour unchanged.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190517174046.11146-5-peter.maydell@linaro.org
Create "vfp" and "dsp" properties on the armv7m container object
which will be forwarded to its CPU object, so that SoCs can
configure whether the CPU has these features.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20190517174046.11146-4-peter.maydell@linaro.org
This is the common header guard idiom:
/*
* File comment
*/
#ifndef GUARD_SYMBOL_H
#define GUARD_SYMBOL_H
... actual contents ...
#endif
A few of our headers have some #include before the guard.
target/tilegx/spr_def_64.h has #ifndef __DOXYGEN__ outside the guard.
A few more have the #define elsewhere.
Change them to match the common idiom. For spr_def_64.h, that means
dropping #ifndef __DOXYGEN__. While there, rename guard symbols to
make scripts/clean-header-guards.pl happy.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190604181618.19980-2-armbru@redhat.com>
[Rebased with conflicts resolved automatically]
No header includes qemu-common.h after this commit, as prescribed by
qemu-common.h's file comment.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190523143508.25387-5-armbru@redhat.com>
[Rebased with conflicts resolved automatically, except for
include/hw/arm/xlnx-zynqmp.h hw/arm/nrf51_soc.c hw/arm/msf2-soc.c
block/qcow2-refcount.c block/qcow2-cluster.c block/qcow2-cache.c
target/arm/cpu.h target/lm32/cpu.h target/m68k/cpu.h target/mips/cpu.h
target/moxie/cpu.h target/nios2/cpu.h target/openrisc/cpu.h
target/riscv/cpu.h target/tilegx/cpu.h target/tricore/cpu.h
target/unicore32/cpu.h target/xtensa/cpu.h; bsd-user/main.c and
net/tap-bsd.c fixed up]
To be coherent with the other peripherals contained in the
BCM2835PeripheralState structure, directly allocate the PL011State
(instead of using the pl011 uart as a pointer to a SysBusDevice).
Initialize the PL011State with object_initialize() instead of
object_new().
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-6-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20190520214342.13709-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The header file hw/arm/arm.h now includes only declarations
relating to hw/arm/boot.c functionality. Rename it accordingly,
and adjust its header comment.
The bulk of this commit was created via
perl -pi -e 's|hw/arm/arm.h|hw/arm/boot.h|' hw/arm/*.c include/hw/arm/*.h
In a few cases we can just delete the #include:
hw/arm/msf2-soc.c, include/hw/arm/aspeed_soc.h and
include/hw/arm/bcm2836.h did not require it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-4-peter.maydell@linaro.org
The system_clock_scale global is used only by the armv7m systick
device; move the extern declaration to the armv7m_systick.h header,
and expand the comment to explain what it is and that it should
ideally be replaced with a different approach.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-2-peter.maydell@linaro.org
Cleaned up with scripts/clean-header-guards.pl.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20190315145123.28030-9-armbru@redhat.com>
We currently use Qemu's default of 128MB. As we know how much ram each
machine ships with, make it easier on users by setting a default.
It can still be overridden with -m on the command line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190503022958.1394-1-joel@jms.id.au
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The ARM virt machines put firmware in flash memory. To configure it,
you use -drive if=pflash,unit=0,... and optionally -drive
if=pflash,unit=1,...
Why two -drive? This permits setting up one part of the flash memory
read-only, and the other part read/write. It also makes upgrading
firmware on the host easier. Below the hood, we get two separate
flash devices, because we were too lazy to improve our flash device
models to support sector protection.
The problem at hand is to do the same with -blockdev somehow, as one
more step towards deprecating -drive.
We recently solved this problem for x86 PC machines, in commit
ebc29e1bea. See the commit message for design rationale.
This commit solves it for ARM virt basically the same way: new machine
properties pflash0, pflash1 forward to the onboard flash devices'
properties. Requires creating the onboard devices in the
.instance_init() method virt_instance_init(). The existing code to
pick up drives defined with -drive if=pflash is replaced by code to
desugar into the machine properties.
There are a few behavioral differences, though:
* The flash devices are always present (x86: only present if
configured)
* Flash base addresses and sizes are fixed (x86: sizes depend on
images, mapped back to back below a fixed address)
* -bios configures contents of first pflash (x86: -bios configures ROM
contents)
* -bios is rejected when first pflash is also configured with -machine
pflash0=... (x86: bios is silently ignored then)
* -machine pflash1=... does not require -machine pflash0=... (x86: it
does).
The actual code is a bit simpler than for x86 mostly due to the first
two differences.
Before the patch, all the action is in create_flash(), called from the
machine's .init() method machvirt_init():
main()
machine_run_board_init()
machvirt_init()
create_flash()
create_one_flash() for flash[0]
create
configure
includes obeying -drive if=pflash,unit=0
realize
map
fall back to -bios
create_one_flash() for flash[1]
create
configure
includes obeying -drive if=pflash,unit=1
realize
map
update FDT
To make the machine properties work, we need to move device creation
to its .instance_init() method virt_instance_init().
Another complication is machvirt_init()'s computation of
@firmware_loaded: it predicts what create_flash() will do. Instead of
predicting what create_flash()'s replacement virt_firmware_init() will
do, I decided to have virt_firmware_init() return what it did.
Requires calling it a bit earlier.
Resulting call tree:
main()
current_machine = object_new()
...
virt_instance_init()
virt_flash_create()
virt_flash_create1() for flash[0]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash0 as alias for drive [NEW]
virt_flash_create1() for flash[1]
create
configure: set defaults
become child of machine [NEW]
add machine prop pflash1 as alias for drive [NEW]
for all machine props from the command line: machine_set_property()
...
property_set_alias() for machine props pflash0, pflash1
...
set_drive() for cfi.pflash01 prop drive
this is how -machine pflash0=... etc set
machine_run_board_init(current_machine);
virt_firmware_init()
pflash_cfi01_legacy_drive()
legacy -drive if=pflash,unit=0 and =1 [NEW]
virt_flash_map()
virt_flash_map1() for flash[0]
configure: num-blocks
realize
map
virt_flash_map1() for flash[1]
configure: num-blocks
realize
map
fall back to -bios
virt_flash_fdt()
update FDT
You have László to thank for making me explain this in detail.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Laszlo Ersek <lersek@redhat.com>
Message-id: 20190416091348.26075-4-armbru@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since uWireSlave is only used in this new header, there is no
need to expose it via "qemu/typedefs.h".
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190412165416.7977-9-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMMUNotifierNode struct is not necessary and brings extra
complexity so let's remove it. We now directly track the SMMUDevices
which have registered IOMMU MR notifiers.
This is inspired from the same transformation on intel-iommu
done in commit b4a4ba0d68
("intel-iommu: remove IntelIOMMUNotifierNode")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-id: 20190409160219.19026-1-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Up to now the memory map has been static and the high IO region
base has always been 256GiB.
This patch modifies the virt_set_memmap() function, which freezes
the memory map, so that the high IO range base becomes floating,
located after the initial RAM and the device memory.
The function computes
- the base of the device memory,
- the size of the device memory,
- the high IO region base
- the highest GPA used in the memory map.
Entries of the high IO region are assigned a base address. The
device memory is initialized.
The highest GPA used in the memory map will be used at VM creation
to choose the requested IPA size.
Setting all the existing highmem IO regions beyond the RAM
allows to have a single contiguous RAM region (initial RAM and
possible hotpluggable device memory). That way we do not need
to do invasive changes in the EDK2 FW to support a dynamic
RAM base.
Still the user cannot request an initial RAM size greater than 255GB.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-8-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In the prospect to introduce an extended memory map supporting more
RAM, let's split the memory map array into two parts:
- the former a15memmap, renamed base_memmap, contains regions below
and including the RAM. MemMapEntries initialized in this array
have a static size and base address.
- extended_memmap, only initialized with entries located after the
RAM. MemMapEntries initialized in this array only get their size
initialized. Their base address is dynamically computed depending
on the the top of the RAM, with same alignment as their size.
Eventually base_memmap entries are copied into the extended_memmap
array. Using two separate arrays however clarifies which entries
are statically allocated and those which are dynamically allocated.
This new split will allow to grow the RAM size without changing the
description of the high IO entries.
We introduce a new virt_set_memmap() helper function which
"freezes" the memory map. We call it in machvirt_init as
memory attributes of the machine are not yet set when
virt_instance_init() gets called.
The memory map is unchanged (the top of the initial RAM still is
256GiB). Then come the high IO regions with same layout as before.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-4-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation for a split of the memory map into a static
part and a dynamic part floating after the RAM, let's rename the
regions located after the RAM
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 20190304101339.25970-3-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create and connect the MHUs in the SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190219125808.25174-3-peter.maydell@linaro.org
The region 0x40010000 .. 0x4001ffff and its secure-only alias
at 0x50010000... are for per-CPU devices. We implement this by
giving each CPU its own container memory region, where the
per-CPU devices live. Unfortunately, the alias region which
makes devices mapped at 0x4... addresses also appear at 0x5...
is only implemented in the overall "all CPUs" container. The
effect of this bug is that the CPU_IDENTITY register block appears
only at 0x4001f000, but not at the 0x5001f000 alias where it should
also appear. Guests (like very recent Arm Trusted Firmware-M)
which try to access it at 0x5001f000 will crash.
Fix this by moving the handling for this alias from the "all CPUs"
container to the per-CPU container. (We leave the aliases for
0x1... and 0x3... in the overall container, because there are
no per-CPU devices there.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20190215180500.6906-1-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
The Musca boards have DAPLink firmware that sets the initial
secure VTOR value (the location of the vector table) differently
depending on the boot mode (from flash, from RAM, etc). Export
the init-svtor as a QOM property of the ARMSSE object so that
the board can change it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
In commit 4b635cf7a9 we added a QOM property to the ARMSSE
object, but forgot to add it to the documentation comment in the
header. Correct the omission.
Fixes: 4b635cf7a9 ("hw/arm/armsse: Make SRAM bank size configurable")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Add a model of the SSE-200, now we have put in all
the code that lets us make it different from the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-22-peter.maydell@linaro.org
Instantiate a copy of the CPU_IDENTITY register block for each CPU
in an SSE-200.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-21-peter.maydell@linaro.org
The SSE-200 has a "CPU local security control" register bank; add an
unimplemented-device stub for it. (The register bank has only one
interesting register, which allows the guest to lock down changes
to various CPU registers so they cannot be modified further. We
don't support that in our Cortex-M33 model anyway.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-19-peter.maydell@linaro.org
The SSE-200 gives each CPU a register bank to use to control its
L1 instruction cache. Put in an unimplemented-device stub for this.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-18-peter.maydell@linaro.org
Add unimplemented-device stubs for the various Power Policy Unit
devices that the SSE-200 has.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-17-peter.maydell@linaro.org
The SSE-200 has two Message Handling Units (MHUs), which sit behind
the APB PPC0. Wire up some unimplemented-device stubs for these,
since we don't yet implement a real model of this device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-16-peter.maydell@linaro.org
Create a cluster object to hold each CPU in the SSE. They are
logically distinct and may be configured differently (for instance
one may not have an FPU where the other does).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-14-peter.maydell@linaro.org
Give each CPU its own container memory region. This is necessary
for two reasons:
* some devices are instantiated one per CPU and the CPU sees only
its own device
* since a memory region can only be put into one container, we must
give each armv7m object a different MemoryRegion as its 'memory'
property, or a dual-CPU configuration will assert on realize when
the second armv7m object tries to put the MR into a container when
it is already in the first armv7m object's container
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-13-peter.maydell@linaro.org
The SSE-200 has two Cortex-M33 CPUs. These see the same view
of memory, with the exception of the "private CPU region" which
has per-CPU devices. Internal device interrupts for SSE-200
devices are mostly wired up to both CPUs, with the exception of
a few per-CPU devices. External GPIO inputs on the SSE-200
device are provided for the second CPU's interrupts above 32,
as is already the case for the first CPU.
Refactor the code to support creation of multiple CPUs.
For the moment we leave all CPUs with the same view of
memory: this will not work in the multiple-CPU case, but
we will fix this in the following commit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-12-peter.maydell@linaro.org
For the IoTKit the SRAM bank size is always 32K (15 bits); for the
SSE-200 this is a configurable parameter, which defaults to 32K but
can be changed when it is built into a particular SoC. For instance
the Musca-B1 board sets it to 128K (17 bits).
Make the bank size a QOM property. We follow the SSE-200 hardware in
naming the parameter SRAM_ADDR_WIDTH, which specifies the number of
address bits of a single SRAM bank.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-11-peter.maydell@linaro.org
The SSE-200 has four banks of SRAM, each with its own
Memory Protection Controller, where the IoTKit has only one.
Make the number of SRAM banks a field in ARMSSEInfo.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-10-peter.maydell@linaro.org
Rename the files that used to be iotkit.[ch] to
armsse.[ch] to reflect the fact they new cover
multiple Arm subsystems for embedded.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-8-peter.maydell@linaro.org
The Arm SSE-200 Subsystem for Embedded is a revised and
extended version of the older IoTKit SoC. Prepare for
adding a model of it by refactoring the IoTKit code into
an abstract base class which contains the functionality,
driven by a class data block specific to each subclass.
(This is the same approach used by the existing bcm283x
SoC family implementation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-6-peter.maydell@linaro.org
The Arm IoTKit was effectively the forerunner of a series of
subsystems for embedded SoCs, named the SSE-050, SSE-100 and SSE-200:
https://developer.arm.com/products/system-design/subsystems
These are generally quite similar, though later iterations have
extra devices that earlier ones do not.
We want to add a model of the SSE-200, which means refactoring the
IoTKit code into an abstract base class and subclasses (using the
same design that the bcm283x SoC and Aspeed SoC family
implementations do). As a first step, rename the IoTKit struct and
QOM macros to ARMSSE, which is what we're going to name the base
class. We temporarily retain TYPE_IOTKIT to avoid changing the
code that instantiates a TYPE_IOTKIT device here and then changing
it back again when it is re-introduced as a subclass.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-5-peter.maydell@linaro.org
Expose "start-powered-off" as a property of the ARMv7M container,
which we just pass through to the CPU object in the same way that we
do for "init-svtor" and "idau". (We want this for the SSE-200, which
powers up only the first CPU at reset and leaves the second powered
down.)
As with the other CPU properties here, we can't just use alias
properties, because the CPU QOM object is not created until armv7m
realize time.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20190121185118.18550-4-peter.maydell@linaro.org
Recent microbit firmwares panic if the TWI magnetometer/accelerometer
devices are not detected during startup. We don't implement TWI (I2C)
so let's stub out these devices just to let the firmware boot.
Signed-off by: Steffen Görtz <contrib@steffen-goertz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190110094020.18354-2-stefanha@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed comment style]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is only one header file requiring this typedef (hw/arm/pxa.h),
let it include "hw/pcmcia.h" directly to simplify "qemu/typedefs.h".
To clean "qemu/typedefs.h", move the declaration to "hw/pcmcia.h"
(removing the forward declaration).
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[thuth: slightly tweaked commit message]
Signed-off-by: Thomas Huth <thuth@redhat.com>
This stubs enables the microbit-micropython firmware to run
on the microbit machine.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-12-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use RNG in SOC.
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-5-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Adds a header that provides definitions that are used
across nRF51 peripherals
Signed-off-by: Steffen Görtz <contrib@steffen-goertz.de>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20190103091119.9367-3-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
From the "A10 User Manual V1.20" p.29: "3.2. Memory Mapping" and:
7. System Control
7.1. Overview
A10 embeds a high-speed SRAM which has been split into five segments.
See detailed memory mapping in following table:
Area Address Size (Bytes)
A1 0x00000000-0x00003FFF 16K
A2 0x00004000-0x00007FFF 16K
A3 0x00008000-0x0000B3FF 13K
A4 0x0000B400-0x0000BFFF 3K
Since for emulation purpose we don't need the segmentations, we simply define
the 'A' area as a single 48KB SRAM.
We don't implement the following others areas:
- 'B': 'Secure RAM' (64K),
- 'C': Debug/ISP SRAM
- 'D': USB SRAM
(qemu) info mtree
address-space: memory
0000000000000000-ffffffffffffffff (prio 0, i/o): system
0000000000000000-000000000000bfff (prio 0, ram): sram A
0000000001c00000-0000000001c00fff (prio -1000, i/o): a10-sram-ctrl
0000000001c0b000-0000000001c0bfff (prio 0, i/o): aw_emac
0000000001c18000-0000000001c18fff (prio 0, i/o): ahci
0000000001c18080-0000000001c180ff (prio 0, i/o): allwinner-ahci
0000000001c20400-0000000001c207ff (prio 0, i/o): allwinner-a10-pic
0000000001c20c00-0000000001c20fff (prio 0, i/o): allwinner-A10-timer
0000000001c28000-0000000001c2801f (prio 0, i/o): serial
0000000040000000-0000000047ffffff (prio 0, ram): cubieboard.ram
Reported-by: Charlie Smurthwaite <charlie@atech.media>
Tested-by: Charlie Smurthwaite <charlie@atech.media>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20190104142921.878-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create two separate CPU clusters for APUs and RPUs.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181207090135.7651-17-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Correct the nr of IRQs to 192.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181129163655.20370-5-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use IRQs 111 - 118 for virtio-mmio. The interrupts we're currently
using 160+ are not available in the Versal GIC.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20181129163655.20370-4-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a model of Xilinx Versal SoC.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20181102131913.1535-2-edgar.iglesias@xilinx.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Wire up nRF51 UART in the corresponding SoC.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The code looks better, it removes duplicated lines and it will ease
the introduction of common properties for the Aspeed machines.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180921161939.822-4-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The nRF51 is a Cortex-M0 microcontroller with an on-board radio module,
plus other common ARM SoC peripherals.
http://infocenter.nordicsemi.com/pdf/nRF51_RM_v3.0.pdf
This defines a basic model of the CPU and memory, with no peripherals
implemented at this stage.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-id: 20180831220920.27113-3-joel@jms.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: wrapped a few long lines]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The IoTKit doesn't have any MSCs itself but it does need
some wiring to connect the external signals from MSCs
in the outer board model up to the registers and the
NVIC IRQ line.
We also need to expose a MemoryRegion corresponding to
the AHB bus, so that MSCs in the outer board model can
use that as their downstream port. (In the FPGA this is
the "AHB Slave Expansion" ports shown in the block
diagram in the AN505 documentation.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180820141116.9118-14-peter.maydell@linaro.org
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Wire up the system control element's register banks
(sysctl and sysinfo).
This is the last of the previously completely unimplemented
components in the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-11-peter.maydell@linaro.org
The IoTKit has a CMSDK timer device that runs on the S32KCLK.
Create this and wire it up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-8-peter.maydell@linaro.org
The IoTKit includes three different instances of the
CMSDK APB watchdog; create and wire them up.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-7-peter.maydell@linaro.org
Now we have a model of the CMSDK dual timer, we can wire it
up in the IoTKit.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180820141116.9118-5-peter.maydell@linaro.org
Some ARM CPUs have bitbanded IO, a memory region that allows convenient
bit access via 32-bit memory loads/stores. This eliminates the need for
read-modify-update instruction sequences.
This patch makes this optional feature an ARMv7MState qdev property,
allowing boards to choose whether they want bitbanding or not.
Status of boards:
* iotkit (Cortex M33), no bitband
* mps2 (Cortex M3), bitband
* msf2 (Cortex M3), bitband
* stellaris (Cortex M3), bitband
* stm32f205 (Cortex M3), bitband
As a side-effect of this patch, Peter Maydell noted that the Ethernet
controller on mps2 board is now accessible. Previously they were hidden
by the bitband region (which does not exist on the real board).
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180814162739.11814-2-stefanha@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for GICv2 virtualization extensions by mapping the necessary
I/O regions and connecting the maintenance IRQ lines.
Declare those additions in the device tree and in the ACPI tables.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20180727095421.386-21-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This commit improve the way the GIC is realized and connected in the
ZynqMP SoC. The security extensions are enabled only if requested in the
machine state. The same goes for the virtualization extensions.
All the GIC to APU CPU(s) IRQ lines are now connected, including FIQ,
vIRQ and vFIQ. The missing CPU to GIC timers IRQ connections are also
added (HYP and SEC timers).
The GIC maintenance IRQs are back-wired to the correct GIC PPIs.
Finally, the MMIO mappings are reworked to take into account the ZynqMP
specifics. The GIC (v)CPU interface is aliased 16 times:
* for the first 0x1000 bytes from 0xf9010000 to 0xf901f000
* for the second 0x1000 bytes from 0xf9020000 to 0xf902f000
Mappings of the virtual interface and virtual CPU interface are mapped
only when virtualization extensions are requested. The
XlnxZynqMPGICRegion struct has been enhanced to be able to catch all
this information.
Signed-off-by: Luc Michel <luc.michel@greensocs.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180727095421.386-20-luc.michel@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
smmu_iommu_mr() aims at returning the IOMMUMemoryRegion corresponding
to a given sid. The function extracts both the PCIe bus number and
the devfn to return this data. Current computation of devfn is wrong
as it only returns the PCIe function instead of slot | function.
Fixes 32cfd7f39e ("hw/arm/smmuv3: Cache/invalidate config data")
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1530775623-32399-1-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
On TLB invalidation commands, let's call registered
IOMMU notifiers. Those can only be UNMAP notifiers.
SMMUv3 does not support notification on MAP (VFIO).
This patch allows vhost use case where IOTLB API is notified
on each guest IOTLB invalidation.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529653501-15358-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We emulate a TLB cache of size SMMU_IOTLB_MAX_SIZE=256.
It is implemented as a hash table whose key is a combination
of the 16b asid and 48b IOVA (Jenkins hash).
Entries are invalidated on TLB invalidation commands, either
globally, or per asid, or per asid/iova.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1529653501-15358-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's cache config data to avoid fetching and parsing STE/CD
structures on each translation. We invalidate them on data structure
invalidation commands.
We put in place a per-smmu mutex to protect the config cache. This
will be useful too to protect the IOTLB cache. The caches can be
accessed without BQL, ie. in IO dataplane. The same kind of mutex was
put in place in the intel viommu.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1529653501-15358-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-10-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
TCMI_VERBOSE is no more used, drop the OMAP_8/16/32B_REG macros.
Suggested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-id: 20180624040609.17572-9-f4bug@amsat.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The interrupt outputs from the MPC in the IoTKit and the expansion
MPCs in the board must be wired up to the security controller, and
also all ORed together to produce a single line to the NVIC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180620132032.28865-8-peter.maydell@linaro.org
Wire up the one MPC that is part of the IoTKit itself. For the
moment we don't wire up its interrupt line.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20180620132032.28865-7-peter.maydell@linaro.org
With this patch, virt-3.0 machine uses a new 256MB ECAM region
by default instead of the legacy 16MB one, if highmem is set
(LPAE supported by the guest) and (!firmware_loaded || aarch64).
Indeed aarch32 mode FW may not support this high ECAM region.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-11-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch defines a new ECAM region located after the 256GB limit.
The virt machine state is augmented with a new highmem_ecam field
which guards the usage of this new ECAM region instead of the legacy
16MB one. With the highmem ECAM region, up to 256 PCIe buses can be
used.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-9-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch allows the creation of a GICv3 node with 1 or 2
redistributor regions depending on the number of smu_cpus.
The second redistributor region is located just after the
existing RAM region, at 256GB and contains up to up to 512 vcpus.
Please refer to kernel documentation for further node details:
Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1529072910-16156-6-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Remove the now-unused armv7m_init() function. This was a legacy from
before we properly QOMified ARMv7M, and it has some flaws:
* it combines work that needs to be done by an SoC object (creating
and initializing the TYPE_ARMV7M object) with work that needs to
be done by the board model (setting the system up to load the ELF
file specified with -kernel)
* TYPE_ARMV7M creation failure is fatal, but an SoC object wants to
arrange to propagate the failure outward
* it uses allocate-and-create via qdev_create() whereas the current
preferred style for SoC objects is to do creation in-place
Board and SoC models can instead do the two jobs this function
was doing themselves, in the right places and with whatever their
preferred style/error handling is.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-id: 20180601144328.23817-3-peter.maydell@linaro.org
The ZynqMP contains two instances of a generic DMA, the GDMA, located in the
FPD (full power domain), and the ADMA, located in LPD (low power domain). This
patch adds these two DMAs to the ZynqMP board.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20180503214201.29082-3-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
load_dtb() depends on arm_load_kernel() to figure out place
in RAM where it should be loaded, but it's not required for
arm_load_kernel() to work. Sometimes it's neccesary for
devices added with -device/device_add to be enumerated in
DTB as well, which's lead to [1] and surrounding commits to
add 2 more machine_done notifiers with non obvious ordering
to make dynamic sysbus devices initialization happen in
the right order.
However instead of moving whole arm_load_kernel() in to
machine_done, it's sufficient to move only load_dtb() into
virt_machine_done() notifier and remove ArmLoadKernelNotifier/
/PlatformBusFDTNotifierParams notifiers, which saves us ~90LOC
and simplifies code flow quite a bit.
Later would allow to consolidate DTB generation within one
function for 'mach-virt' board and make it reentrant so it
could generate updated DTB in device hotplug secenarios.
While at it rename load_dtb() to arm_load_dtb() since it's
public now.
Add additional field skip_dtb_autoload to struct arm_boot_info
to allow manual DTB load later in mach-virt and to avoid touching
all other boards to explicitly call arm_load_dtb().
1) (ac9d32e hw/arm/boot: arm_load_kernel implemented as a machine init done notifier)
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1525691524-32265-4-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
platform-bus were using machine_done notifier to get and map
(assign irq/mmio resources) dynamically added sysbus devices
after all '-device' options had been processed.
That however creates non obvious dependencies on ordering of
machine_done notifiers and requires carefull line juggling
to keep it working. For example see comment above
create_platform_bus() and 'straitforward' arm_load_kernel()
had to converted to machine_done notifier and that lead to
yet another machine_done notifier to keep it working
arm_register_platform_bus_fdt_creator().
Instead of hiding resource assignment in platform-bus-device
to magically initialize sysbus devices, use device plug
callback and assign resources explicitly at board level
at the moment each -device option is being processed.
That adds a bunch of machine declaration boiler plate to
e500plat board, similar to ARM/x86 but gets rid of hidden
machine_done notifier and would allow to remove the dependent
notifiers in ARM code simplifying it and making code flow
easier to follow.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-id: 1525691524-32265-3-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add code to instantiate an smmuv3 in virt machine. A new iommu
integer member is introduced in VirtMachineState to store the type
of the iommu in use.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-13-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements a skeleton for the smmuv3 device.
Datatypes and register definitions are introduced. The MMIO
region, the interrupts and the queue are initialized.
Only the MMIO read operation is implemented here.
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch implements the page table walk for VMSAv8-64.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Message-id: 1524665762-31355-4-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We set up the infrastructure to enumerate all the PCI devices
attached to the SMMU and create an associated IOMMU memory
region and address space.
Those info are stored in SMMUDevice objects. The devices are
grouped according to the PCIBus they belong to. A hash table
indexed by the PCIBus pointer is used. Also an array indexed by
the bus number allows to find the list of SMMUDevices.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The patch introduces the smmu base device and class for the ARM
smmu. Devices for specific versions will be derived from this
base device.
We also introduce some important datatypes.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Prem Mallappa <prem.mallappa@broadcom.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1524665762-31355-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of using "1.0" as the system version of SMBIOS, we should use
mc->name for mach-virt machine type to be consistent other architectures.
With this patch, "dmidecode -t 1" (e.g., "-M virt-2.12,accel=kvm") will
show:
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: QEMU
Product Name: KVM Virtual Machine
Version: virt-2.12
Serial Number: Not Specified
...
instead of:
Handle 0x0100, DMI type 1, 27 bytes
System Information
Manufacturer: QEMU
Product Name: KVM Virtual Machine
Version: 1.0
Serial Number: Not Specified
...
For backward compatibility, we allow older machine types to keep "1.0"
as the default system version.
Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20180322212318.7182-1-wei@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The bcm2837 is pretty similar to the bcm2836, but it does have
some differences. Notably, the MPIDR affinity aff1 values it
sets for the CPUs are 0x0, rather than the 0xf that the bcm2836
uses, and if this is wrong Linux will not boot.
Rather than trying to have one device with properties that
configure it differently for the two cases, create two
separate QOM devices for the two SoCs. We use the same approach
as hw/arm/aspeed_soc.c and share code and have a data table
that might differ per-SoC. For the moment the two types don't
actually have different behaviour.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-7-peter.maydell@linaro.org
Our BCM2836 type is really a generic one that can be any of
the bcm283x family. Rename it accordingly. We change only
the names which are visible via the header file to the
rest of the QEMU code, leaving private function names
in bcm2836.c as they are.
This is a preliminary to making bcm283x be an abstract
parent class to specific types for the bcm2836 and bcm2837.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180313153458.26822-6-peter.maydell@linaro.org
The sabrelite machine model used by qemu-system-arm is based on the
Freescale/NXP i.MX6Q processor. This SoC has an on-board ethernet
controller which is supported in QEMU using the imx_fec.c module
(actually called imx.enet for this model.)
The include/hw/arm/fsm-imx6.h file defines the interrupt vectors for the
imx.enet device like this:
#define FSL_IMX6_ENET_MAC_1588_IRQ 118
#define FSL_IMX6_ENET_MAC_IRQ 119
According to https://www.nxp.com/docs/en/reference-manual/IMX6DQRM.pdf,
page 225, in Table 3-1. ARM Cortex A9 domain interrupt summary,
interrupts are as follows.
150 ENET MAC 0 IRQ
151 ENET MAC 0 1588 Timer interrupt
where
150 - 32 == 118
151 - 32 == 119
In other words, the vector definitions in the fsl-imx6.h file are reversed.
Fixing the interrupts alone causes problems with older Linux kernels:
The Ethernet interface will fail to probe with Linux v4.9 and earlier.
Linux v4.1 and earlier will crash due to a bug in Ethernet driver probe
error handling. This is a Linux kernel problem, not a qemu problem:
the Linux kernel only worked by accident since it requested both interrupts.
For backward compatibility, generate the Ethernet interrupt on both interrupt
lines. This was shown to work from all Linux kernel releases starting with
v3.16.
Link: https://bugs.launchpad.net/qemu/+bug/1753309
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 1520723090-22130-1-git-send-email-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Create an "init-svtor" property on the armv7m container
object which we can forward to the CPU object.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-8-peter.maydell@linaro.org
Create an "idau" property on the armv7m container object which
we can forward to the CPU object. Annoyingly, we can't use
object_property_add_alias() because the CPU object we want to
forward to doesn't exist until the armv7m container is realized.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180220180325.29818-6-peter.maydell@linaro.org
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch adds a "cpu-type" property to BCM2836 SoC in preparation for
reusing the code for the Raspberry Pi 3, which has a different processor
model.
Signed-off-by: Pekka Enberg <penberg@iki.fi>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Replace all occurs of __FUNCTION__ except for the check in checkpatch
with the non GCC specific __func__.
One line in hcd-musb.c was manually tweaked to pass checkpatch.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Anthony PERARD <anthony.perard@citrix.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
[THH: Removed hunks related to pxa2xx_mmci.c (fixed already)]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Some i.MX SoCs (e.g. i.MX7) have FEC registers going as far as offset
0x614, so to avoid getting aborts when accessing those on QEMU, extend
the register file to cover FSL_IMX25_FEC_SIZE(16K) of address space
instead of just 1K.
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Cc: qemu-devel@nongnu.org
Cc: qemu-arm@nongnu.org
Cc: yurovsky@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add support for the ZynqMP QSPI (consisting of the Generic QSPI and Legacy
QSPI) and connect Numonyx n25q512a11 flashes to it.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20171126231634.9531-14-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
s/cpu_model/cpu_type/ that has been forgotten during
conversion (ba1ba5cc), while touching the line also
fixup alignment.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Message-id: 1507710805-221721-1-git-send-email-imammedo@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Since FlatViews are shared now and ASes not, this gets rid of
address_space_init_shareable().
This should cause no behavioural change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20170921085110.25598-17-aik@ozlabs.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Smartfusion2 SoC has hardened Microcontroller subsystem
and flash based FPGA fabric. This patch adds support for
Microcontroller subsystem in the SoC.
Signed-off-by: Subbaraya Sundeep <sundeep.lkml@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170920201737.25723-5-f4bug@amsat.org
[PMD: drop cpu_model to directly use cpu type, check m3clk non null]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
there are 2 use cases to deal with:
1: fixed CPU models per board/soc
2: boards with user configurable cpu_model and fallback to
default cpu_model if user hasn't specified one explicitly
For the 1st
drop intermediate cpu_model parsing and use const cpu type
directly, which replaces:
typename = object_class_get_name(
cpu_class_by_name(TYPE_ARM_CPU, cpu_model))
object_new(typename)
with
object_new(FOO_CPU_TYPE_NAME)
or
cpu_generic_init(BASE_CPU_TYPE, "my cpu model")
with
cpu_create(FOO_CPU_TYPE_NAME)
as result 1st use case doesn't have to invoke not necessary
translation and not needed code is removed.
For the 2nd
1: set default cpu type with MachineClass::default_cpu_type and
2: use generic cpu_model parsing that done before machine_init()
is run and:
2.1: drop custom cpu_model parsing where pattern is:
typename = object_class_get_name(
cpu_class_by_name(TYPE_ARM_CPU, cpu_model))
[parse_features(typename, cpu_model, &err) ]
2.2: or replace cpu_generic_init() which does what
2.1 does + create_cpu(typename) with just
create_cpu(machine->cpu_type)
as result cpu_name -> cpu_type translation is done using
generic machine code one including parsing optional features
if supported/present (removes a bunch of duplicated cpu_model
parsing code) and default cpu type is defined in an uniform way
within machine_class_init callbacks instead of adhoc places
in boadr's machine_init code.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <1505318697-77161-6-git-send-email-imammedo@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Add a machine level virtualization property. This defaults to false and can be
set to true using this machine command line argument:
-machine xlnx-zcu102,virtualization=on
This follows what the ARM virt machine does.
This property only applies to the ZCU102 machine. The EP108 machine does
not have this property.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The armv7m_nvic.h header file was accidentally placed in
include/hw/arm; move it to include/hw/intc to match where
its corresponding .c file lives.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 1501692241-23310-15-git-send-email-peter.maydell@linaro.org
The ast2400 contains two and the ast2500 contains three watchdogs.
Add this information to the AspeedSoCInfo and realise the correct number
of watchdogs for that each SoC type.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Before QOM-ifying the Exynos4 SoC model, move the DRAM initialization
from exynos4210.c to exynos4_boards.c because DRAM is board specific,
not SoC.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
There is a second NIC but we do not use it for the moment. We use the
'aspeed' property to tune the definition of the end of ring buffer bit
for the Aspeed SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This adds the bcm2835_sdhost and bcm2835_gpio to the BCM2835 platform.
For supporting the SD controller selection (alternate function of GPIOs
48-53), the bcm2835_gpio now exposes an sdbus.
It also has a link to both the sdbus of sdhci and sdhost controllers,
and the card is reparented from one bus to another when the alternate
function of GPIOs 48-53 is modified.
Signed-off-by: Clement Deschamps <clement.deschamps@antfield.fr>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1488293711-14195-5-git-send-email-peter.maydell@linaro.org
Message-id: 20170224164021.9066-5-clement.deschamps@antfield.fr
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Switch the stm32f205 SoC to create the armv7m object directly
rather than via the armv7m_init() wrapper. This fits better
with the SoC model's very QOMified design.
In particular this means we can push loading the guest image
out to the top level board code where it belongs, rather
than the SoC object having a QOM property for the filename
to load.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-11-git-send-email-peter.maydell@linaro.org
The SysTick timer isn't really part of the NVIC proper;
we just modelled it that way back when we couldn't
easily have devices that only occupied a small chunk
of a memory region. Split it out into its own device.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1487604965-23220-10-git-send-email-peter.maydell@linaro.org
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Instead of the bitband device doing a cpu_physical_memory_read/write,
make it take a MemoryRegion which specifies where it should be
accessing, and use address_space_read/write to access the
corresponding AddressSpace.
Since this entails pretty much a rewrite, convert away from
old_mmio in the process.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-8-git-send-email-peter.maydell@linaro.org
Make the ARMv7M object take a memory region link which it uses
to wire up the bitband rather than having them always put
themselves in the system address space.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-6-git-send-email-peter.maydell@linaro.org
Create a proper QOM object for the armv7m container, which
holds the CPU, the NVIC and the bitband regions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-4-git-send-email-peter.maydell@linaro.org
Move the NVICState struct definition into a header, so we can
embed it into other QOM objects like SoCs.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-3-git-send-email-peter.maydell@linaro.org
Abstract the "load kernel" code out of armv7m_init() into its own
function. This includes the registration of the CPU reset function,
to parallel how we handle this for A profile cores.
We make the function public so that boards which choose to
directly instantiate an ARMv7M device object can call it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1487604965-23220-2-git-send-email-peter.maydell@linaro.org
In 2.9 ITS will block save/restore and migration use cases. As such,
let's introduce a user option that allows to turn its instantiation
off, along with GICv3. With the "its" option turned false, migration
will be possible, obviously at the expense of MSI support (with GICv3).
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1487681108-14452-1-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Recent vanilla Raspberry Pi kernels started to make use of
the hardware random number generator in BCM2835 SoC. As a
result, those kernels wouldn't work anymore under QEMU
but rather just freeze during the boot process.
This patch implements a trivial BCM2835 compatible RNG,
and adds it as a peripheral to BCM2835 platform, which
allows to boot a vanilla Raspberry Pi kernel under Qemu.
Changes since v1:
* Prevented guest from writing [31..20] bits in rng_status
* Removed redundant minimum_version_id_old
* Added field entries for the state
* Changed realize function to reset
Signed-off-by: Marcin Chojnacki <marcinch7@gmail.com>
Message-id: 20170210210857.47893-1-marcinch7@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This enables reboot of a guest from U-Boot and Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-id: 1485452251-1593-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Pick a uniform chardev type name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a board level property to the virt board which will
enable EL2 on the CPU if the user asks for it. The
default is not to provide EL2. If EL2 is enabled then
we will use SMC as our PSCI conduit, and report the
virtualization support in the GICv3 device tree node
and the ACPI tables.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-19-git-send-email-peter.maydell@linaro.org
If we are giving the guest a CPU with EL2, it is likely to
want to use the HVC instruction itself, for instance for
providing PSCI to inner guest VMs. This makes using HVC
as the PSCI conduit for the outer QEMU a bad idea. We will
want to use SMC instead is this case: this makes sense
because QEMU's PSCI implementation is effectively an
emulation of functionality provided by EL3 firmware.
Add code to support selecting the PSCI conduit to use,
rather than hardcoding use of HVC.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1483977924-14522-15-git-send-email-peter.maydell@linaro.org
Wire the new VIRQ, VFIQ and maintenance interrupt lines from the
GIC to each CPU.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1483977924-14522-5-git-send-email-peter.maydell@linaro.org
by moving VirtGuestInfo.fw_cfg to VirtMachineState. This is the
mach-virt equivalent of "pc: Move PcGuestInfo.fw_cfg to
PCMachineState" and "pc: Eliminate PcGuestInfo struct" combined.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-14-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Now that we pass VirtMachineState, and guest-info is just part of
that state, we can remove all the redundant members and access
the VirtMachineState directly.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-12-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Only two functions take VirtGuestInfo parameters. Now that guest-info
is part of VirtMachineState, and VirtMachineState is defined in the
virt header, pass that instead.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-11-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
In preparation to share more Virt machine state than just guest-info
with other mach-virt source files, move the State and Class structures
to virt.h
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-10-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
include/hw/arm/virt-acpi-build.h is only used for VirtGuestInfo,
which doesn't even necessarily have to be ACPI specific. Move
VirtGuestInfo to include/hw/arm/virt.h, allowing us to remove
include/hw/arm/virt-acpi-build.h, and to prepare for even more
code motion.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-9-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Instead of allocating a new struct just for VirtGuestInfo and the
machine_done Notifier, place them inside VirtMachineState. This
is the mach-virt equivalent of "pc: Eliminate struct
PcGuestInfoState"
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20170102200153.28864-8-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Also move the enabled flag definition from mach-virt code to
acpi common.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Message-id: 20170102200153.28864-3-drjones@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The size of the SRAM depends on the SoC model, so use a per-soc
definition when creating the region.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1480434248-27138-9-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1480434248-27138-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
We've currently got 18 architectures in QEMU, and thus 18 target-xxx
folders in the root folder of the QEMU source tree. More architectures
(e.g. RISC-V, AVR) are likely to be included soon, too, so the main
folder of the QEMU sources slowly gets quite overcrowded with the
target-xxx folders.
To disburden the main folder a little bit, let's move the target-xxx
folders into a dedicated target/ folder, so that target-xxx/ simply
becomes target/xxx/ instead.
Acked-by: Laurent Vivier <laurent@vivier.eu> [m68k part]
Acked-by: Bastian Koppelmann <kbastian@mail.uni-paderborn.de> [tricore part]
Acked-by: Michael Walle <michael@walle.cc> [lm32 part]
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x part]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com> [s390x part]
Acked-by: Eduardo Habkost <ehabkost@redhat.com> [i386 part]
Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> [sparc part]
Acked-by: Richard Henderson <rth@twiddle.net> [alpha part]
Acked-by: Max Filippov <jcmvbkbc@gmail.com> [xtensa part]
Reviewed-by: David Gibson <david@gibson.dropbear.id.au> [ppc part]
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> [crisµblaze part]
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn> [unicore32 part]
Signed-off-by: Thomas Huth <thuth@redhat.com>
We should avoid exposing new hardware (through DT and ACPI) on older
machine types. This patch keeps 2.7 and older from changing, despite
the introduction of ITS support for 2.8.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1476117341-32690-3-git-send-email-drjones@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The SMC controllers on the Aspeed AST2500 SoC are very similar to the
ones found on the AST2400. The differences are on the number of
supported flash modules and their default mappings in the SoC address
space.
The Aspeed AST2500 has one SPI controller for the BMC firmware and two
for the host firmware. All controllers have now the same set of
registers compatible with the AST2400 FMC controller and the legacy
'SMC' controller is fully gone.
We keep the FMC object to act as the BMC SPI controller and add a new
SPI controller for the host. We also have to introduce new type names
to handle the differences in the flash modules memory mappping.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-5-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The AST2500 SoC has two. Let's prepare ground for the next changes
which will add the required definitions for the second host SPI
controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed SoC has three different types of SMC (Static Memory
Controller) controllers: the SMC (legacy), the FMC (the new one) and
the SPI for the host PNOR. The FMC and the SPI models are now
converging on the AST2500 SoC and the SMC, which was still available
on the AST2400 SoC, was removed.
The Aspeed SoC does not provide support for the legacy SMC
controller. So, let's rename the 'smc' object to 'fmc' to clarify its
nature.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1474977462-28032-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's define an object class for each Aspeed SoC we support. A
AspeedSoCInfo struct gathers the SoC specifications which can later be
used by an instance of the class or by a board using the SoC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1473438177-26079-4-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a name replacement to prepare ground for other SoCs.
Let's also remove the AST2400_SMC_BASE definition from the address
space mappings, as it is not used. This controller was removed from
the Aspeed SoC AST2500, so this provides us a better common base for
the address space mapping on both SoCs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-3-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Let's prepare for new Aspeed SoCs and rename the ast2400 file to a
more generic one. There are no changes in the code apart from the
header file include.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1473438177-26079-2-git-send-email-clg@kaod.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Unused function declarations were found using a simple gcc plugin and
manually verified by grepping the sources.
Signed-off-by: Ladi Prosek <lprosek@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
The uboot in the previous release of the SDK was using a hardcoded
value for memory size. This is not true anymore, the value is now
retrieved from the memory controller.
Below is a model for this device, only supporting unlock and
configuration. Without it, we endup running a guest with 64MB, which
is a bit low nowdays. It uses a 'silicon-rev' property and ram_size to
build a default value. Some bits should be linked to SCU strapping
registers but it seems a bit complex to add for the current need.
The model is ready for the AST2500 SOC.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Header guard symbols should match their file name to make guard
collisions less likely. Offenders found with
scripts/clean-header-guards.pl -vn.
Cleaned up with scripts/clean-header-guards.pl, followed by some
renaming of new guard symbols picked by the script to better ones.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
The Aspeed AST2400 soc includes a static memory controller for the BMC
which supports NOR, NAND and SPI flash memory modules. This controller
has two modes : the SMC for the legacy interface which supports only
one module and the FMC for the new interface which supports up to five
modules. The AST2400 also includes a SPI only controller used for the
host firmware, commonly called BIOS on Intel. It can be used in three
mode : a SPI master, SPI slave and SPI pass-through
Below is the initial framework for the SMC controller (FMC mode only)
and the SPI controller: the sysbus object, MMIO for registers
configuration and controls. Each controller has a SPI bus and a
configurable number of CS lines for SPI flash slaves.
The differences between the controllers are small, so they are
abstracted using indirections on the register numbers.
Only SPI flash modules are supported.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-id: 1467138270-32481-7-git-send-email-clg@kaod.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: added one missing error_propagate]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
By specifying the silicon revision we select the appropriate reset
values for the SoC.
Additionally, expose hardware strapping properties aliasing those
provided by the SCU for board-specific configuration.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1466744305-23163-3-git-send-email-andrew@aj.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the DP and the DPDMA to the Zynq MP platform.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Message-id: 1465833014-21982-10-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a virtual PMU device for virt machine while use PPI 7 for PMU
overflow interrupt number.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 1465267577-1808-3-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The way we currently model the RPU subsystem is of quite
limited use. In addition to that, it causes problems for
KVM and for GDB debugging.
Make the RPU optional by adding a has_rpu property and
default to having it disabled.
This changes the default setup from having the RPU to not
longer having it.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1464173555-12800-3-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a secure prop to en/disable ARM Security Extensions.
This is particularly useful for KVM runs.
Default to disabled to match the behavior of KVM.
This changes the default setup from having the ARM Security
Extensions to not longer having them.
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1464173555-12800-2-git-send-email-edgar.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Aspeed AST2400 integrates a set of 14 I2C/SMBus bus controllers
directly connected to the APB bus. They can be programmed as master or
slave but the propopsed model only supports the master mode.
On the TODO list, we also have :
- improve and harden the state machine.
- bus recovery support (used by the Linux driver).
- transfer mode state machine bits. this is not strictly necessary as
it is mostly used for debug. The bus busy bit is deducted from the
I2C core engine of qemu.
- support of the pool buffer: 2048 bytes of internal SRAM (not used
by the Linux driver).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1464704307-25178-1-git-send-email-clg@kaod.org
[PMM: removed unused functions aspeed_i2c_bus_get_state() and
aspeed_i2c_bus_set_state()]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This adds the ENET device to the i.MX6 SOC.
This was tested by booting Linux on an Qemu i.MX6 instance and accessing
the internet from the linux guest.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
This will keep things working when cpu.h will not be included
indirectly almost everywhere (either directly or through
qemu-common.h).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
At present, all DMA transfers complete inline (so a looping descriptor
queue will lock up the device). We also do not model pause/abort,
arbitrarion/priority, or debug features.
Signed-off-by: Grégory ESTRADE <gregory.estrade@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1457467526-8840-6-git-send-email-Andrew.Baumann@microsoft.com
[AB: implement 2D mode, cleanup/refactoring for upstream submission]
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The framebuffer occupies the upper portion of memory (64MiB by
default), but it can only be controlled/configured via a system
mailbox or property channel (to be added by a subsequent patch).
Signed-off-by: Grégory ESTRADE <gregory.estrade@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Message-id: 1457467526-8840-4-git-send-email-Andrew.Baumann@microsoft.com
[AB: added Windows (BGR) support and cleanup/refactoring for upstream submission]
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
At present only the core UART functions (data path for tx/rx) are
implemented, which is enough for UEFI to boot. The following
features/registers are unimplemented:
* Line/modem control
* Scratch register
* Extra control
* Baudrate
* SPI interfaces
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1457467526-8840-3-git-send-email-Andrew.Baumann@microsoft.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
While the ASPEED AST2400 SoC[1] has a broad range of capabilities this
implementation is minimal, comprising an ARM926 processor, ASPEED VIC
and timer devices, and a 8250 UART.
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-4-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Support ARM big-endian ELF files in system-mode emulation. When loading
an elf, determine the endianness mode expected by the elf, and set the
relevant CPU state accordingly.
With this, big-endian modes are now fully supported via system-mode LE,
so there is no need to restrict the elf loading to the TARGET
endianness so the ifdeffery on TARGET_WORDS_BIGENDIAN goes away.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fix typo in comments]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
If we're booting in Secure mode, provide a secure-only RAM
(just 16MB) so that secure firmware has somewhere to run
from that won't be accessible to the Non-secure guest.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1455288361-30117-2-git-send-email-peter.maydell@linaro.org
The new version is slightly different, to support Rasbperry Pi (in
particular, Pi1's arm11 core which doesn't support v7 instructions
such as MOVW).
Tested-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is the SoC for Raspberry Pi 2.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This device maintains all the non-CPU peripherals on bcm2835 (Pi1)
which are also present on bcm2836 (Pi2). It also implements the
private address spaces used for DMA and mailboxes.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
in current impl. condition
build_madt() {
...
if (test_bit(i, cpuinfo->found_cpus))
is always true since loop handles only present CPUs
in range [0..smp_cpus).
But to fill usless cpuinfo->found_cpus we do unnecessary
scan over QOM tree to find the same CPUs.
So mark GICC as present always and drop not needed
code that fills cpuinfo->found_cpus.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1454323689-248759-1-git-send-email-imammedo@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a secure memory region to the virt board, which is the
same as the nonsecure memory region except that it also has
a secure-only UART in it. This is only created if the
board is started with the '-machine secure=on' property.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Connect the Xilinx SPI devices to the ZynqMP model.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
[ PC changes
* Use QOM alias for bus connectivity on SoC level
]
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
[PMM: free the g_strdup_printf() string when finished with it]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The Xilinx ZynqMP SoC and EP108 board supports three memory regions:
- A 2GB region starting at 0
- A 32GB region starting at 32GB
- A 256GB region starting at 768GB
This patch adds support for the first two memory regions, which is
automatically created based on the size specified by the QEMU memory
command line argument.
On hardware the physical memory region is one continuous region, it is then
mapped into the three different regions by the DDRC. As we don't model the
DDRC this is done at startup by QEMU. The board creates the memory region and
then passes that memory region to the SoC. The SoC then maps the memory
regions.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: a1e47db941d65733724a300fcd98b74fbeeaaf22.1452637205.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
With this CCM, i.MX25 timer is accurate with "real world time".
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 2c0cf90be767bfc8520661eca891ab22c61f18fe.1449528242.git.jcd@tribudubois.net
Reviewed-by Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The IMX_CCM class is now the base abstract class that is used by EPIT
and GPT timer implementation.
IMX31_CCM class is the concrete class implementing CCM for i.MX31 SOC.
For now the i.MX25 continues to use the i.MX31 CCM implementation.
An i.MX25 specific CCM will be introduced in a later patch.
We also rework initialization to stop using deprecated sysbus device init.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: fd3c7f87b50f5ebc99ec91f01413db35017f116d.1449528242.git.jcd@tribudubois.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
ACPI 5.0 supports GPIO-signaled ACPI Events. This can be used for
powerdown, hotplug evnets. Add a GPIO controller in machine virt,
to support powerdown, maybe can be used for cpu hotplug. And
here we use pl061.
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Wei Huang <wei@redhat.com>
Tested-by: Wei Huang <wei@redhat.com>
Message-id: 1449804086-3464-4-git-send-email-zhaoshenglong@huawei.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add a flag that when set, will cause the primary CPU to start in secure
mode, even if the overall boot is non-secure. This is useful for when
there is a board-setup blob that needs to run from secure mode, but
device and secondary CPU init should still be done as-normal for a non-
secure boot.
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: d1170774d5446d715fced7739edfc61a5be931f9.1447007690.git.crosthwaite.peter@gmail.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Change armv7m_init to return the DeviceState* for the NVIC.
This allows access to all GPIO blocks, not just the IRQ inputs.
Move qdev_get_gpio_in() calls out of armv7m_init() into
board code for stellaris and stm32f205 boards.
Signed-off-by: Michael Davidsaver <mdavidsaver@gmail.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add an API for boards to inject their own preboot software (or
firmware) sequence.
The software then returns to the bootloader via the link register. This
allows boards to do their own little bits of firmware setup without
needed to replace the bootloader completely (which is the requirement
for existing firmware support).
The blob is loaded by a callback if and only if doing a linux boot
(similar to the existing write_secondary support).
Rewrite the comment for the primary boot blob.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Message-id: 070295644c6ac84696d743913296e8cfefb48c15.1446182614.git.crosthwaite.peter@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Add two SYSBUS_SDHCI devices for xlnx-zynqmp
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Add gic_version to VirtMachineState, set it to value of the option
and pass it around where necessary. Instantiate devices and fdt
nodes according to the choice.
max_cpus for virt machine increased to 123 (calculated from redistributor
space available in the memory map). GICv2 compatibility check happens
inside arm_gic_common_realize().
ITS region is added to the memory map too, however currently it not used,
just reserved.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Tested-by: Ashok kumar <ashoks@broadcom.com>
[PMM: Added missing cpu_to_le* calls, thanks to Shannon Zhao]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The GIC in ZynqMP cover a 64K address space, however the actual
registers are decoded within a 4K address space and mirrored at the 4K
boundaries. This change fixes the defined size for these regions as it
was set to 0x4000/16K incorrectly.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 1441719672-25296-1-git-send-email-nathan@nathanrossi.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Niek Linnenbank
Guenter Roeck
Edgar E. Iglesias
Eric Auger
Roman Kapl
Andrew Jones
Cédric Le Goater
Andrew Jeffery
Martin Kaiser
Philippe Mathieu-Daudé
Alistair Francis
Marc-André Lureau
Philippe Mathieu-Daudé
Clement Deschamps
Peter Maydell
Joel Stanley
Eddie James
Shameer Kolothum
Rashmica Gupta
Tao Xu
Markus Armbruster
Andrey Smirnov
Steffen Görtz
Luc Michel
Julia Suvorova
Stefan Hajnoczi
Jean-Christophe Dubois
Francisco Iglesias
Igor Mammedov
Prem Mallappa
Wei Huang
Alistair Francis
Pekka Enberg
Alexey Kardashevskiy
Subbaraya Sundeep
Krzysztof Kozlowski
Clement Deschamps
Marcin Chojnacki
Thomas Huth
Alistair Francis
Ladi Prosek
KONRAD Frederic
Shannon Zhao
Paolo Bonzini
Grégory ESTRADE
Andrew Baumann
Peter Crosthwaite
Michael Davidsaver
Sai Pavan Boddu
Pavel Fedin
Nathan Rossi