The expectation of x86-64-branch-3 for "call" / "jmp" with an obvious
direct destination to translate to an indirect _far_ branch is plain
wrong. The operand size prefix should have no effect at all on the
interpretation of the operand. The main underlying issue here is that
the Intel64 templates of the direct branches don't include Disp16, yet
various assumptions exist that it would always be there when there's
also Disp32/Disp32S, toggled by the operand size prefix (which is
being ignored by direct branches in Intel64 mode).
Along these lines it was also wrong to base the displacement width
decision solely on the operand size prefix: REX.W cancels this effect
and hence needs taking into consideration, too.
A disassembler change is needed here as well: XBEGIN was wrongly treated
the same as direct CALL/JMP, which isn't the case - the operand size
prefix does affect displacement size there, it's merely ignored when it
comes to updating [ER]IP.
In memory operand addressing, which forms of displacement are permitted
besides Disp8 is pretty clearly limited
- outside of 64-bit mode, Disp16 or Disp32 only, depending on address
size (MPX being special in not allowing Disp16),
- in 64-bit mode, Disp32s or Disp64 without address size override, and
solely Disp32 with one.
Adjust assembler and i386-gen to match this, observing that templates
already get adjusted before trying to match them against input depending
on the presence of an address size prefix.
This adjustment logic gets extended to all cases, as certain DispNN
values should also be dropped when there's no such prefix. In fact
behavior of the assembler, perhaps besides the exact diagnostics wording,
should not differ between there being templates applicable to 64-bit and
non-64-bit at the same time, or there being fully separate sets of
templates, with their DispNN settings already reduced accordingly.
This adjustment logic further gets guarded such that there wouldn't be
and Disp<N> conversion based on address size prefix when this prefix
doesn't control the width of the displacement (on branches other than
absolute ones).
These adjustments then also allow folding two MOV templates, which had
been split between 64-bit and non-64-bits variants so far.
Once in this area also
- drop the bogus DispNN from JumpByte templates, leaving just the
correct Disp8 there (compensated by i386_finalize_displacement()
now setting Disp8 on their operands),
- add the missing Disp32S to XBEGIN.
Note that the changes make it necessary to temporarily mark a test as
XFAIL; this will get taken care of by a subsequent patch. The failing
parts are entirely bogus and will get replaced.
* d30v-dis.c (extract_value): Make num param a uint64_t, constify
oper. Use unsigned vars.
(print_insn): Make num var uint64_t. Constify oper and remove now
unnecessary casts on extract_value calls.
(print_insn_d30v): Use unsigned vars. Adjust printf formats.
PR 25281
* sh-dis.c (print_insn_ddt): Properly check validity of MOVX_NOPY
and MOVY_NOPX insns. For invalid cases include 0xf000 in the word
printed. Print .word in more cases.
This patch prevents print_insn_mode recursing into another index mode
byte, which if repeated enough times will overflow private.the_buffer
and scribble over other memory.
* vax-dis.c (print_insn_mode): Stop index mode recursion.
fadd, fmul, and fdiv are now, by ISO/IEC TS 18661-3:2015, defined to
refer to functions from the runtime subsystem.
PR 25277
* microblaze-opcm.h (enum microblaze_instr): Prefix fadd, fmul and
fdiv with "mbi_".
* microblaze-opc.h (opcodes): Adjust to suit.
The arc fix in create_map avoiding signed overflow by casting an
unsigned char to unsigned int before shifting, shows one of the
dangers of blinding doing that. The problem in this case was that the
variable storing the value, newAuxRegister->address, was a long.
Using the unsigned cast meant that the 32-bit value was zero extended
when long is 64 bits. Previously we had a sign extension. Net result
was that comparisons in arcExtMap_auxRegName didn't match. Of course,
I could have cast the 32-bit unsigned value back to signed before
storing in a long, but it's neater to just use an unsigned int for the
address.
opcodes/
* alpha-opc.c (OP): Avoid signed overflow.
* arm-dis.c (print_insn): Likewise.
* mcore-dis.c (print_insn_mcore): Likewise.
* pj-dis.c (get_int): Likewise.
* ppc-opc.c (EBD15, EBD15BI): Likewise.
* score7-dis.c (s7_print_insn): Likewise.
* tic30-dis.c (print_insn_tic30): Likewise.
* v850-opc.c (insert_SELID): Likewise.
* vax-dis.c (print_insn_vax): Likewise.
* arc-ext.c (create_map): Likewise.
(struct ExtAuxRegister): Make "address" field unsigned int.
(arcExtMap_auxRegName): Pass unsigned address.
(dump_ARC_extmap): Adjust.
* arc-ext.h (arcExtMap_auxRegName): Update prototype.
I'm flying blind here, not having an s+core s3 insn set reference,
but this seems reasonably obvious from what is done by the assembler.
s3_do16_rpop does some mixing of imm and reg values to place in the
rpop reg field, but I'm not going to try to fix the disassembly
there.
* score-dis.c (print_insn_score16): Move rpush/rpop imm field
value adjustment so that it doesn't affect reg field too.
The ubsan complaint is fixed by the SBM change, with similar possible
complaints fixed by the EXTRACT change. The rest is just cleanup.
include/
* opcode/crx.h (inst <match>): Make unsigned int.
opcodes/
* crx-dis.c (EXTRACT, SBM): Avoid signed overflow.
(get_number_of_operands, getargtype, getbits, getregname),
(getcopregname, getprocregname, gettrapstring, getcinvstring),
(getregliststring, get_word_at_PC, get_words_at_PC, build_mask),
(powerof2, match_opcode, make_instruction, print_arguments),
(print_arg): Delete forward declarations, moving static to..
(getregname, getcopregname, getregliststring): ..these definitions.
(build_mask): Return unsigned int mask.
(match_opcode): Use unsigned int vars.
Note that using 1u in N32_BIT makes all of N32_BIT, __MASK, __MF, __GF
and __SEXT evaluate as unsigned int (the latter three when when their
v arg is int or smaller). This would be a problem if assigning the
result to a bfd_vma, long, or other type wider than an int since the
__SEXT result would be zero extended to the wider type. Fortunately
nds32 target code doesn't use wider types unnecessarily.
include/
* opcode/nds32.h (N32_BIT): Define using 1u.
(__SEXT): Use __MASK and N32_BIT.
(N32_IMMS): Remove duplicate mask.
opcodes/
* nds32-dis.c (print_insn16, print_insn32): Remove forward decls.
(struct objdump_disasm_info): Delete.
(nds32_parse_audio_ext, nds32_parse_opcode): Cast result of
N32_IMMS to unsigned before shifting left.
Commit 8c9b417187 didn't remove a glaring left shift of a number
that had just been sign extended.
* moxie-dis.c (INST2OFFSET): Don't left shift a signed value.
(print_insn_moxie): Remove unnecessary cast.
This is
*cst = (data[0] << 24) + (data[1] << 16) + (data[2] << 8) + data[3];
data is unsigned char which promotes to int.
* h8300-dis.c (extract_immediate): Avoid signed overflow.
(bfd_h8_disassemble): Likewise.
In the following buf is an unsigned char array, so elements are
promoted to int before arithmetic operations.
if (dis_info.info->endian == BFD_ENDIAN_BIG)
while (n--)
val |= buf[n] << (n*8);
else
for (i = 0; i < n; i++)
val |= buf[i] << (i*8);
* csky-dis.c (csky_chars_to_number): Rewrite. Avoid signed
overflow when collecting bytes of a number.
This was the following in print_with_operands
case 4:
number
= buffer[2] + buffer[3] * 256 + buffer[4] * 65536
+ buffer[5] * 0x1000000;
and buffer[5] * 0x1000000 can indeed overflow. So to fix this we need
to use unsigned arithmetic where overflow semantics are specified.
But number is a long, and the expression is int which will be sign
extended to long. If we make the expression unsigned it will be zero
extended. So make number an int32_t and rearrange a little for some
of the places that need fixing.
* cris-dis.c (print_with_operands): Avoid signed integer
overflow when collecting bytes of a 32-bit integer.
This was:
unsigned long mask = SBM (instruction->match_bits);
with
#define SBM(offs) ((((1 << (32 - offs)) -1) << (offs)))
Well, there are a couple of problems. Firstly, the expression uses
int values (1 rather than 1u or 1ul) resulting in the ubsan error, and
secondly, a zero offs will result in a 32-bit shift which is undefined
if ints are only 32 bits.
* cr16-dis.c (EXTRACT, SBM): Rewrite.
(cr16_match_opcode): Delete duplicate bcond test.
This was the following in fmtconst_val, x is unsigned int.
x = SIGNEXTEND (x, constant_formats[cf].nbits);
Problem is, the SIGNEXTEND macro assumed its arg was a long and sign
extended by shifting left then shifting right, and didn't cast the
arg. So don't do the silly shift thing. It's not guaranteed to work
anyway according to the C standard. ">>" might do a logical shift
even if its args are signed.
* bfin-dis.c (HOST_LONG_WORD_SIZE, XFIELD): Delete.
(SIGNBIT): New.
(MASKBITS, SIGNEXTEND): Rewrite.
(fmtconst): Don't use ? expression now that SIGNEXTEND uses
unsigned arithmetic, instead assign result of SIGNEXTEND back
to x.
(fmtconst_val): Use 1u in shift expression.
When operand->bits is 32, the following results in UB.
value = (insn >> operand->shift) & ((1 << operand->bits) - 1);
* arc-dis.c (find_format_from_table): Use ull constant when
shifting by up to 32.
Assembling this to an object and trying to disassemble results in
objdump -d looping forever.
.inst 0x45205120
PR 25270
* aarch64-dis.c (aarch64_decode_variant_using_iclass): Return
false when field is zero for sve_size_tsz_bhs.
Two places in epiphany_cgen_extract_operand, "value" is a long.
value = ((((value) << (1))) + (pc));
cpu/
* epiphany.cpu (f-simm8, f-simm24): Use multiply rather than
shift left to avoid UB on left shift of negative values.
opcodes/
* epiphany-ibld.c: Regenerate.
ppc-dis.c used a global struct whenever malloc failed to provide the
eight bytes of memory necessary for struct dis_private. Which is
quite ridiculous. If that malloc failed there is zero chance some
other malloc won't fail too.
* ppc-dis.c (private): Delete variable.
(get_powerpc_dialect): Don't segfault on NULL info->private_data.
(powerpc_init_dialect): Don't use global private.
This, at the assembler level, is just a "brace" feature covering both
AES and SHA2. Hence there's no need for it to have a separate feature
flag, freeing up a bit for future re-use. Along these lines there are
also a number of dead definitions/variables in the opcode table file.
Since we accept these without suffix / operand size specifier, we should
also do so with one. (The fact that we unilaterally accept these, other
than far branches, rather than limiting them to Intel64 mode, will be
taken care of later on.)
Also take the opportunity and make sure "lfs <reg>, tbyte ptr <mem>"
et al get rejected outside of 64-bit mode. This became broken by
dc2be329b9 ("i386: Only check suffix in instruction mnemonic").
Furthermore cover lgdt et al in the Intel syntax handling as well, which
continued to work after said commit just by coincidence.
Test also memory operands with operand size specifier, which was broken
prior to dc2be329b9 ("i386: Only check suffix in instruction
mnemonic"), due to the template not permitting any suffixes. Note that
this uncovered a disassembler issue, which is being fixed here as well.
Insns permitting only GPR operands (and hence implicit sizing when
there's no suffix) don't ever have their DefaultSize attribute
inspected, so it shouldn't be there in the first place.
Additionally XBEGIN is like JMP, not CALL, and hence shouldn't be
converted to 32-bit operand size in .code16gcc mode. While the same is
true for SYSRET, it permitting more than one suffix makes it FLDENV-
like, and hence rather than dropping the attribute, for now add it to
the exclusion list to avoid it getting an operand size prefix emitted
in .code16gcc mode. (This will be dealt with later, perhaps together
with FLDENV and friends.)
This patch changes the CRC extension to use the core feature bits instead
of the coproc/fpu feature bits.
CRC is not an fpu feature and it causes issues with the new fpu reset
patch (f439988037). CRC can be set using
the '.arch_extension' directive, which sets bits in the coproc bitfield. When
a '.fpu' directive is encountered, the CRC feature bit gets removed and
there is no way to set it back using '.fpu'.
With this patch, CRC will be marked in the feature core bits, which prevents
it from getting removed when setting/changing the fpu options.
gas/ChangeLog:
* config/tc-arm.c (arm_ext_crc): New.
(crc_ext_armv8): Remove.
(insns): Rename crc_ext_armv8 to arm_ext_crc.
(arm_cpus): Replace CRC_EXT_ARMV8 with ARM_EXT2_CRC.
(armv8a_ext_table, armv8r_ext_table,
arm_option_extension_value_table): Redefine the crc
extension in terms of ARM_EXT2_CRC.
* gas/testsuite/gas/arm/crc-ext.s: New.
* gas/testsuite/gas/arm/crc-ext.d: New.
include/ChangeLog:
* opcode/arm.h (ARM_EXT2_CRC): New extension feature
to replace CRC_EXT_ARMV8.
(CRC_EXT_ARMV8): Remove and mark bit as unused.
(ARM_ARCH_V8A_CRC, ARM_ARCH_V8_1A, ARM_ARCH_V8_2A,
ARM_ARCH_V8_3A, ARM_ARCH_V8_4A, ARM_ARCH_V8_5A,
ARM_ARCH_V8_6A): Redefine using ARM_EXT2_CRC instead of
CRC_EXT_ARMV8.
opcodes/ChangeLog:
* opcodes/arm-dis.c (arm_opcodes, thumb32_opcodes):
Change the coproc CRC conditions to use the extension
feature set, second word, base on ARM_EXT2_CRC.
The Cpu64 forms are no different in their attributes except for the CPU
flags; there's no need to key these off of anything other than
CpuSYSCALL even for the 64-bit forms. Dropping these improves the
diagnostic on SYSRETQ used in 32-bit code from "unsupported instruction
`sysret'" to "invalid instruction suffix for `sysret'".
... instead of an operand one. Which operand it applies to can be
determined from other operand properties, but as it turns out the only
place it is actually used at doesn't even need further qualification.
We have to enable the f extension through -march or ELF attribute if we use the
FPR in .insn directive. The behavior is same as the riscv_opcodes.
2019-11-12 Nelson Chu <nelson.chu@sifive.com>
opcodes/
* riscv-opc.c (riscv_insn_types): Replace the INSN_CLASS_I with
INSN_CLASS_F and the INSN_CLASS_C with INSN_CLASS_F_AND_C if we
use the floating point register (FPR).
gas/
* testsuite/gas/riscv/insn.d: Add the f extension to -march option.
Change-Id: I4f59d04c82673ef84c56ecd2659ad8ce164dd626
This patch updates the decoding of the VMOV and VMVN instructions which depend on cmode.
Previously VMOV and VMVN with cmode 1101 were not allowed.
The cmode changes also required updating of the MVE conflict checking.
Now instructions with opcodes 0xef800d50 and 0xef800e70 correctly get decoded as VMOV
and VMVN, respectively.
2019-11-12 Mihail Ionescu <mihail.ionescu@arm.com>
* opcodes/arm-dis.c (mve_opcodes): Enable VMOV imm to vec with
cmode 1101.
(is_mve_encoding_conflict): Update cmode conflict checks for
MVE_VMVN_IMM.
2019-11-12 Mihail Ionescu <mihail.ionescu@arm.com>
* gas/config/tc-arm.c (do_neon_mvn): Allow mve_ext cmode=0xd.
* testsuite/gas/arm/mve-vmov-vmvn-vorr-vbic.s: New test.
* testsuite/gas/arm/mve-vmov-vmvn-vorr-vbic.d: Likewise.
EsSeg (a per-operand bit) is used with IsString (a per-insn attribute)
only. Extend the attribute to 2 bits, thus allowing to encode
- not a string insn,
- string insn with neither operand requiring use of %es:,
- string insn with 1st operand requiring use of %es:,
- string insn with 2nd operand requiring use of %es:,
which covers all possible cases, allowing to drop EsSeg.
The (transient) need to comment out the OTUnused #define did uncover an
oversight in the earlier OTMax -> OTNum conversion, which is being taken
care of here.
Drop the remaining instances left in place by commit c3949f432f ("x86:
limit ImmExt abuse), now that we have a way to specify specific GPRs.
Take the opportunity and also introduce proper 16-bit forms of
applicable SVME insns as well as 1-operand forms of CLZERO.
Special register "class" instances can't be combined with one another
(neither in templates nor in register entries), and hence it is not a
good use of resources (memory as well as execution time) to represent
them as individual bits of a bit field.
Furthermore the generalization becoming possible will allow
improvements to the handling of insns accepting only individual
registers as their operands.
Some old glibc versions have string.h surface "index", which some
compilers then warn about if shadowed by a local variable. Re-use an
existing variable instead.
We should check suffix in instruction mnemonic when matching instruction.
In Intel syntax, normally we check for memory operand size. But the same
mnemonic with 2 different encodings can have the same memory operand
size and i.suffix is set to LONG_DOUBLE_MNEM_SUFFIX from memory operand
size in Intel syntax to distinguish them. When there is no suffix in
mnemonic, we check LONG_DOUBLE_MNEM_SUFFIX in i.suffix for mnemonic
suffix.
gas/
PR gas/25167
* config/tc-i386.c (match_template): Don't check instruction
suffix set from operand.
* testsuite/gas/i386/code16.d: New file.
* testsuite/gas/i386/code16.s: Likewise.
* testsuite/gas/i386/i386.exp: Run code16.
* testsuite/gas/i386/x86-64-branch-4.l: Updated.
opcodes/
PR gas/25167
* i386-opc.tbl: Remove IgnoreSize from cmpsd and movsd.
* i386-tbl.h: Regenerated.
Many operand types, in particular the various kinds of registers, can't
be combined with one another (neither in templates nor in register
entries), and hence it is not a good use of resources (memory as well as
execution time) to represent them as individual bits of a bit field.
Hi,
This patch is part of a series that adds support for Armv8.6-A
to binutils.
In this last patch, the new Data Gathering Hint mnemonic is introduced.
Committed on behalf of Mihail Ionescu.
gas/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
* testsuite/gas/aarch64/dgh.s: New test.
* testsuite/gas/aarch64/dgh.d: New test.
opcodes/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
* opcodes/aarch64-tbl.h (V8_6_INSN): New macro for v8.6 instructions.
(aarch64_opcode_table): Add data gathering hint mnemonic.
* opcodes/aarch64-dis-2.c: Account for new instruction.
Is it ok for trunk?
Regards,
Mihail
Hi,
This patch is part of a series that adds support for Armv8.6-A
(Matrix Multiply and BFloat16 extensions) to binutils.
This patch introduces the Matrix Multiply (Int8, F32, F64) extensions
to the arm backend.
The following Matrix Multiply instructions are added: vummla, vsmmla,
vusmmla, vusdot, vsudot[1].
[1]https://developer.arm.com/docs/ddi0597/latest/simd-and-floating-point-instructions-alphabetic-order
Committed on behalf of Mihail Ionescu.
gas/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
* config/tc-arm.c (arm_ext_i8mm): New feature set.
(do_vusdot): New.
(do_vsudot): New.
(do_vsmmla): New.
(do_vummla): New.
(insns): Add vsmmla, vummla, vusmmla, vusdot, vsudot mnemonics.
(armv86a_ext_table): Add i8mm extension.
(arm_extensions): Move bf16 extension to context sensitive table.
(armv82a_ext_table, armv84a_ext_table, armv85a_ext_table):
Move bf16 extension to context sensitive table.
(armv86a_ext_table): Add i8mm extension.
* doc/c-arm.texi: Document i8mm extension.
* testsuite/gas/arm/i8mm.s: New test.
* testsuite/gas/arm/i8mm.d: New test.
* testsuite/gas/arm/bfloat17-cmdline-bad-3.d: Update test.
include/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
* opcode/arm.h (ARM_EXT2_I8MM): New feature macro.
opcodes/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
* arm-dis.c (neon_opcodes): Add i8mm SIMD instructions.
Regression tested on arm-none-eabi.
Is this ok for trunk?
Regards,
Mihail
Hi,
This patch is part of a series that adds support for Armv8.6-A
(Matrix Multiply and BFloat16 extensions) to binutils.
This patch introduces the Matrix Multiply (Int8, F32, F64) extensions
to the aarch64 backend.
The following instructions are added: {s/u}mmla, usmmla, {us/su}dot,
fmmla, ld1rob, ld1roh, d1row, ld1rod, uzip{1/2}, trn{1/2}.
Committed on behalf of Mihail Ionescu.
gas/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
* config/tc-aarch64.c: Add new arch fetures to suppport the mm extension.
(parse_operands): Add new operand.
* testsuite/gas/aarch64/i8mm.s: New test.
* testsuite/gas/aarch64/i8mm.d: New test.
* testsuite/gas/aarch64/f32mm.s: New test.
* testsuite/gas/aarch64/f32mm.d: New test.
* testsuite/gas/aarch64/f64mm.s: New test.
* testsuite/gas/aarch64/f64mm.d: New test.
* testsuite/gas/aarch64/sve-movprfx-mm.s: New test.
* testsuite/gas/aarch64/sve-movprfx-mm.d: New test.
include/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
* opcode/aarch64.h (AARCH64_FEATURE_I8MM): New.
(AARCH64_FEATURE_F32MM): New.
(AARCH64_FEATURE_F64MM): New.
(AARCH64_OPND_SVE_ADDR_RI_S4x32): New.
(enum aarch64_insn_class): Add new instruction class "aarch64_misc" for
instructions that do not require special handling.
opcodes/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
* aarch64-tbl.h (aarch64_feature_i8mm_sve, aarch64_feature_f32mm_sve,
aarch64_feature_f64mm_sve, aarch64_feature_i8mm, aarch64_feature_f32mm,
aarch64_feature_f64mm): New feature sets.
(INT8MATMUL_INSN, F64MATMUL_SVE_INSN, F64MATMUL_INSN,
F32MATMUL_SVE_INSN, F32MATMUL_INSN): New macros to define matrix multiply
instructions.
(I8MM_SVE, F32MM_SVE, F64MM_SVE, I8MM, F32MM, F64MM): New feature set
macros.
(QL_MMLA64, OP_SVE_SBB): New qualifiers.
(OP_SVE_QQQ): New qualifier.
(INT8MATMUL_SVE_INSNC, F64MATMUL_SVE_INSNC,
F32MATMUL_SVE_INSNC): New feature set for bfloat16 instructions to support
the movprfx constraint.
(aarch64_opcode_table): Support for SVE_ADDR_RI_S4x32.
(aarch64_opcode_table): Define new instructions smmla,
ummla, usmmla, usdot, sudot, fmmla, ld1rob, ld1roh, ld1row, ld1rod
uzip{1/2}, trn{1/2}.
* aarch64-opc.c (operand_general_constraint_met_p): Handle
AARCH64_OPND_SVE_ADDR_RI_S4x32.
(aarch64_print_operand): Handle AARCH64_OPND_SVE_ADDR_RI_S4x32.
* aarch64-dis-2.c (aarch64_opcode_lookup_1, aarch64_find_next_opcode):
Account for new instructions.
* opcodes/aarch64-asm-2.c (aarch64_insert_operand): Support the new
S4x32 operand.
* aarch64-opc-2.c (aarch64_operands): Support the new S4x32 operand.
Regression tested on arm-none-eabi.
Is it ok for trunk?
Regards,
Mihail
Hi,
This patch is part of a series that adds support for Armv8.6-A
(Matrix Multiply and BFloat16 extensions) to binutils.
This patch introduces BFloat16 instructions to the arm backend.
The following BFloat16 instructions are added: vdot, vfma{l/t},
vmmla, vfmal{t/b}, vcvt, vcvt{t/b}.
gas/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
2019-11-07 Matthew Malcomson <matthew.malcomson@arm.com>
* config/tc-arm.c (arm_archs): Add armv8.6-a option.
(cpu_arch_ver): Add TAG_CPU_ARCH_V8 tag for Armv8.6-a.
* doc/c-arm.texi (-march): New armv8.6-a arch.
* config/tc-arm.c (arm_ext_bf16): New feature set.
(enum neon_el_type): Add NT_bfloat value.
(B_MNEM_vfmat, B_MNEM_vfmab): New bfloat16 encoder
helpers.
(BAD_BF16): New message.
(parse_neon_type): Add bf16 type specifier.
(enum neon_type_mask): Add N_BF16 type.
(type_chk_of_el_type): Account for NT_bfloat.
(el_type_of_type_chk): Account for N_BF16.
(neon_three_args): Split out from neon_three_same.
(neon_three_same): Part split out into neon_three_args.
(CVT_FLAVOUR_VAR): Add bf16_f32 cvt flavour.
(do_neon_cvt_1): Account for vcvt.bf16.f32.
(do_bfloat_vmla): New.
(do_mve_vfma): New function to deal with the mnemonic clash between the BF16
vfmat and the MVE vfma in a VPT block with a 't'rue condition.
(do_neon_cvttb_1): Account for vcvt{t,b}.bf16.f32.
(do_vdot): New
(do_vmmla): New
(insns): Add vdot and vmmla mnemonics.
(arm_extensions): Add "bf16" extension.
* doc/c-arm.texi: Document "bf16" extension.
* testsuite/gas/arm/attr-march-armv8_6-a.d: New test.
* testsuite/gas/arm/bfloat16-bad.d: New test.
* testsuite/gas/arm/bfloat16-bad.l: New test.
* testsuite/gas/arm/bfloat16-bad.s: New test.
* testsuite/gas/arm/bfloat16-cmdline-bad-2.d: New test.
* testsuite/gas/arm/bfloat16-cmdline-bad-3.d: New test.
* testsuite/gas/arm/bfloat16-cmdline-bad.d: New test.
* testsuite/gas/arm/bfloat16-neon.s: New test.
* testsuite/gas/arm/bfloat16-non-neon.s: New test.
* testsuite/gas/arm/bfloat16-thumb-bad.d: New test.
* testsuite/gas/arm/bfloat16-thumb-bad.l: New test.
* testsuite/gas/arm/bfloat16-thumb.d: New test.
* testsuite/gas/arm/bfloat16-vfp.d: New test.
* testsuite/gas/arm/bfloat16.d: New test.
* testsuite/gas/arm/bfloat16.s: New test.
include/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
2019-11-07 Matthew Malcomson <matthew.malcomson@arm.com>
* opcode/arm.h (ARM_EXT2_V8_6A, ARM_AEXT2_V8_6A,
ARM_ARCH_V8_6A): New.
* opcode/arm.h (ARM_EXT2_BF16): New feature macro.
(ARM_AEXT2_V8_6A): Include above macro in definition.
opcodes/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
2019-11-07 Matthew Malcomson <matthew.malcomson@arm.com>
* arm-dis.c (select_arm_features): Update bfd_march_arm_8 with
Armv8.6-A.
(coprocessor_opcodes): Add bfloat16 vcvt{t,b}.
(neon_opcodes): Add bfloat SIMD instructions.
(print_insn_coprocessor): Add new control character %b to print
condition code without checking cp_num.
(print_insn_neon): Account for BFloat16 instructions that have no
special top-byte handling.
Regression tested on arm-none-eabi.
Is it ok for trunk?
Regards,
Mihail
Hi,
This patch is part of a series that adds support for Armv8.6-A
(Matrix Multiply and BFloat16 extensions) to binutils.
Some generic instructions match a large range of encoding space (e.g.
stc, mcr, mrc).
Currently these instructions are in the coprocessor_opcodes array, which
means they are checked before many other instructions when disassembling
arm and thumb32 codes.
This patch moves the generic instructions into a separate array to be
checked later on.
This is done in order to avoid instruction conflict between the generic
instructions and newer ones -- this has already been seen with MVE, and
is also a problem with BFloat16.
One way to avoid the conflict could be to swap the search order between
coprocessor_opcodes and neon_opcodes.
We avoid this since it's a larger change that may introduce extra bugs
(that aren't caught by the testsuite).
We have decided against searching the generic array after searching the
arm specific and thumb32 specific arrays with a similar reasoning about
keeping the change small.
Regression tested with arm-none-linux-gnueabihf.
Committed on behalf of Mihail Ionescu.
opcodes/ChangeLog:
2019-10-29 Mihail Ionescu <mihail.ionescu@arm.com>
2019-10-29 Matthew Malcomson <matthew.malcomson@arm.com>
* arm-dis.c (print_insn_coprocessor,
print_insn_generic_coprocessor): Create wrapper functions around
the implementation of the print_insn_coprocessor control codes.
(print_insn_coprocessor_1): Original print_insn_coprocessor
function that now takes which array to look at as an argument.
(print_insn_arm): Use both print_insn_coprocessor and
print_insn_generic_coprocessor.
(print_insn_thumb32): As above.
Is it ok for trunk?
Regards,
Mihail
Hi,
This patch is part of a series that adds support for Armv8.6-A
(Matrix Multiply and BFloat16 extensions) to binutils.
This patch introduces the following BFloat16 instructions to the
aarch64 backend: bfdot, bfmmla, bfcvt, bfcvtnt, bfmlal[t/b],
bfcvtn2.
Committed on behalf of Mihail Ionescu.
gas/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
2019-11-07 Matthew Malcomson <matthew.malcomson@arm.com>
* config/tc-aarch64.c (vectype_to_qualifier): Special case the
S_2H operand qualifier.
* doc/c-aarch64.texi: Document bf16 and bf16mmla4 extensions.
* testsuite/gas/aarch64/bfloat16.d: New test.
* testsuite/gas/aarch64/bfloat16.s: New test.
* testsuite/gas/aarch64/illegal-bfloat16.d: New test.
* testsuite/gas/aarch64/illegal-bfloat16.l: New test.
* testsuite/gas/aarch64/illegal-bfloat16.s: New test.
* testsuite/gas/aarch64/sve-bfloat-movprfx.s: New test.
* testsuite/gas/aarch64/sve-bfloat-movprfx.d: New test.
include/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
2019-11-07 Matthew Malcomson <matthew.malcomson@arm.com>
* opcode/aarch64.h (AARCH64_FEATURE_BFLOAT16): New feature macros.
(AARCH64_ARCH_V8_6): Include BFloat16 feature macros.
(enum aarch64_opnd_qualifier): Introduce new operand qualifier
AARCH64_OPND_QLF_S_2H.
(enum aarch64_insn_class): Introduce new class "bfloat16".
(BFLOAT16_SVE_INSNC): New feature set for bfloat16
instructions to support the movprfx constraint.
opcodes/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
2019-11-07 Matthew Malcomson <matthew.malcomson@arm.com>
* aarch64-asm.c (aarch64_ins_reglane): Use AARCH64_OPND_QLF_S_2H
in reglane special case.
* aarch64-dis-2.c (aarch64_opcode_lookup_1,
aarch64_find_next_opcode): Account for new instructions.
* aarch64-dis.c (aarch64_ext_reglane): Use AARCH64_OPND_QLF_S_2H
in reglane special case.
* aarch64-opc.c (struct operand_qualifier_data): Add data for
new AARCH64_OPND_QLF_S_2H qualifier.
* aarch64-tbl.h (QL_BFDOT QL_BFDOT64, QL_BFDOT64I, QL_BFMMLA2,
QL_BFCVT64, QL_BFCVTN64, QL_BFCVTN2_64): New qualifiers.
(aarch64_feature_bfloat16, aarch64_feature_bfloat16_sve,
aarch64_feature_bfloat16_bfmmla4): New feature sets.
(BFLOAT_SVE, BFLOAT): New feature set macros.
(BFLOAT_SVE_INSN, BFLOAT_BFMMLA4_INSN, BFLOAT_INSN): New macros
to define BFloat16 instructions.
(aarch64_opcode_table): Define new instructions bfdot,
bfmmla, bfcvt, bfcvtnt, bfdot, bfdot, bfcvtn, bfmlal[b/t]
bfcvtn2, bfcvt.
Regression tested on aarch64-elf.
Is it ok for trunk?
Regards,
Mihail
Hi,
This patch is part of a series that adds support for Armv8.6-A
to binutils.
This first patch adds the Armv8.6-A flag to binutils.
No instructions are behind it at the moment.
Commited on behalf of Mihail Ionescu.
gas/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
2019-11-07 Matthew Malcomson <matthew.malcomson@arm.com>
* config/tc-aarch64.c (armv8.6-a): New arch.
* doc/c-aarch64.texi (armv8.6-a): Document new arch.
include/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
2019-11-07 Matthew Malcomson <matthew.malcomson@arm.com>
* opcode/aarch64.h (AARCH64_FEATURE_V8_6): New.
(AARCH64_ARCH_V8_6): New.
opcodes/ChangeLog:
2019-11-07 Mihail Ionescu <mihail.ionescu@arm.com>
2019-11-07 Matthew Malcomson <matthew.malcomson@arm.com>
* aarch64-tbl.h (ARMV8_6): New macro.
Is it ok for trunk?
Regards,
Mihail
As the comments (here: almost, in the opcode table: fully) correctly
state - all register operands except MONITOR's address one are fixed
at 32 bit size. Don't print 64-bit registers there.
Also adjust x86-64-suffix.d's name such that it wouldn't be identical to
x86-64-rep-suffix.d's, but instead resemble that of its sibling
x86-64-suffix-intel.d.
The original idea looks to have been for names to be composed in the
order that decoding gets done, which helps both reading and modifying
the code. Switch (back) to this model for some of the affected non-
vector insn enumerators.
* v850-dis.c (get_v850_sreg_name): New function. Returns the name
of a v850 system register. Move the v850_sreg_names array into
this function.
(get_v850_reg_name): Likewise for ordinary register names.
(get_v850_vreg_name): Likewise for vector register names.
(get_v850_cc_name): Likewise for condition codes.
* get_v850_float_cc_name): Likewise for floating point condition
codes.
(get_v850_cacheop_name): Likewise for cache-ops.
(get_v850_prefop_name): Likewise for pref-ops.
(disassemble): Use the new accessor functions.
This is a shorthand for the immediate argument being 0, as described here:
https://developer.arm.com/docs/ddi0596/latest/base-instructions-alphabetic-order/ldraa-ldrab-load-register-with-pointer-authentication
This is because the instructions still have a use with an immediate
argument of 0, unlike loads without the PAC functionality. Currently,
the mnemonics are
LDRAA Xt, [Xn, #<simm10>]!
LDRAB Xt, [Xn, #<simm10>]!
After this patch they become
LDRAA Xt, [Xn {, #<simm10>}]!
LDRAB Xt, [Xn {, #<simm10>}]!
gas * config/tc-aarch64.c (parse_address_main): Accept the omission of
the immediate argument for ldraa and ldrab as a shorthand for the
immediate being 0.
* testsuite/gas/aarch64/ldraa-ldrab-no-offset.d: New test.
* testsuite/gas/aarch64/ldraa-ldrab-no-offset.s: New test.
* testsuite/gas/aarch64/illegal-ldraa.s: Modified to accept the
writeback form with no offset.
* testsuite/gas/aarch64/illegal-ldraa.s: Removed missing offset
error.
opcodes * aarch64-opc.c (print_immediate_offset_address): Don't print the
immediate for the writeback form of ldraa/ldrab if it is 0.
* aarch64-tbl.h: Updated the documentation for ADDR_SIMM10.
* aarch64-opc-2.c: Regenerated.
Now that the opcode table gets preprocessed, undo parts of commit
dc821c5f9a ("x86: replace Reg8, Reg16, Reg32, and Reg64"): Have the
preprocessor handle the expansion there, while making the expansions
explicit in i386-gen and the register table.
The flag is used to indicate opcodes which can be switched between byte
and word/dword/qword forms (in a "canonical" way). Obviously it's quite
odd then to see it on insns not allowing for byte operands in the first
place. As a result the opcode bytes need to be adjusted accordingly,
which includes comparisons done in optimize_encoding().
To make re-introduction of such issues less likely have i386-gen
diagnose it (in a generally non-fatal way for now).
* s12z-dis.c (opr_emit_disassembly): Check for illegal register
values.
(shift_size_table): Use a fixed size defined as S12Z_N_SIZES.
(print_insn_s12z): Check for illegal size values.
* tic30-dis.c (OPERAND_BUFFER_LEN): Define. Use as length of
operand buffer. Set value to 15 not 13.
(get_register_operand): Use OPERAND_BUFFER_LEN.
(get_indirect_operand): Likewise.
(print_two_operand): Likewise.
(print_three_operand): Likewise.
(print_oar_insn): Likewise.
* ns32k-dis.c (bit_extract): Add sanitiy check of parameters.
(bit_extract_simple): Likewise.
(bit_copy): Likewise.
(pirnt_insn_ns32k): Ensure that uninitialised elements in the
index_offset array are not accessed.
* rx-dis.c (get_size_name): New function. Provides safe
access to name array.
(get_opsize_name): Likewise.
(print_insn_rx): Use the accessor functions.
opcodes * rx-dis.c (get_register_name): New function. Provides safe
access to name array.
(get_condition_name, get_flag_name, get_double_register_name)
(get_double_register_high_name, get_double_register_low_name)
(get_double_control_register_name, get_double_condition_name):
Likewise.
(print_insn_rx): Use the accessor functions.
PR 25041
opcodes * avr-dis.c (avr_operand): Fix construction of address for lds/sts
instructions.
gas * testsuite/gas/avr/pr25041.s: New test.
* testsuite/gas/avr/pr25041.d: New test driver.
First and foremost the EsSeg attribute was misplaced for CMPSD. Then
both it and MOVSD were lacking Dword on both of their operands.
Finally string insns with multiple operands and requiring use of ES:
had the wrong operand number reported in the diagnostic.
Commit 21df382b91 ("x86: fold SReg{2,3}") went too far: Folding 64-bit
PUSH/POP templates into non-64-bit ones isn't correct, due to the
different operand widths, and hence suffixes permitted. Restore the
separate templates.
Add tests of PUSH/POP with q suffix and %fs/%gs operands to the
testsuite. While doing so also add PUSHF/POPF ones _without_ suffix.
I get some spurious changes when running autoconf/automake for various
projects in the tree. This is likely because they were generated using
distro-patched tools last time.
I ran `autoreconf -f` in the various automake projects of the
binutils-gdb tree, and this is the result. The tools I am using have
been compiled from source, from the upstream release.
bfd/ChangeLog:
* Makefile.in: Re-generate.
* configure: Re-generate.
* doc/Makefile.in: Re-generate.
binutils/ChangeLog:
* Makefile.in: Re-generate.
* configure: Re-generate.
* doc/Makefile.in: Re-generate.
gas/ChangeLog:
* Makefile.in: Re-generate.
* configure: Re-generate.
* doc/Makefile.in: Re-generate.
gold/ChangeLog:
* testsuite/Makefile.in: Re-generate.
gprof/ChangeLog:
* Makefile.in: Re-generate.
* configure: Re-generate.
ld/ChangeLog:
* Makefile.in: Re-generate.
* configure: Re-generate.
opcodes/ChangeLog:
* Makefile.in: Re-generate.
* configure: Re-generate.
Generalize opcode arch dependencies so that we can support the
overlapping B extension Zb* subsets.
2019-09-17 Maxim Blinov <maxim.blinov@embecosm.com>
gas/
* config/tc-riscv.c (riscv_multi_subset_supports): Handle
insn_class enum rather than subset char string.
(riscv_ip): Update call to riscv_multi_subset_supports.
include/
* opcode/riscv.h (riscv_insn_class): New enum.
* opcode/riscv.h (struct riscv_opcode): Change
subset field to insn_class field.
opcodes/
* riscv-opc.c (riscv_opcodes): Change subset field
to insn_class field for all instructions.
(riscv_insn_types): Likewise.
PR 24958
* mmix-dis.c (MAX_REG_NAME_LEN): Define.
(MAX_SPEC_REG_NAME_LEN): Define.
(struct mmix_dis_info): Use defined constants for array lengths.
(get_reg_name): New function.
(get_sprec_reg_name): New function.
(print_insn_mmix): Use new functions.
gas * config/tc-arm.c (parse_neon_mov): Add check to accept vector
register to both the arguments in VMOV instruction.
* testsuite/gas/arm/mve-vmov-1.d: Modify.
* testsuite/gas/arm/mve-vmov-1.s: Likewise.
* testsuite/gas/arm/mve-vorr.d: Likewise.
opcodes * arm-dis.c (mve_opcodes): Add entry for MVE_VMOV_VEC_TO_VEC.
(is_mve_undefined): Add case for MVE_VMOV_VEC_TO_VEC.
(print_insn_mve): Add condition to check Qm==Qn of VORR instruction.
This is a change to the first published specifications [1][a] but since there is no hardware
out there that uses the old instructions we do not want to support the old variant.
This changes are done based on the latest published specifications [1][b].
[1] https://developer.arm.com/architectures/cpu-architecture/m-profile/docs/ddi0553/latest/armv81-m-architecture-reference-manual
[a] version bf
[b] version bh
gas * config/tc-arm.c (enum operand_parse_code): Add the entry OP_I48_I64.
(po_imm1_or_imm2_or_fail): Marco to check the immediate is either of
48 or 64.
(parse_operands): Add case OP_I48_I64.
(do_mve_scalar_shift1): Add function to encode the MVE shift
instructions with 4 arguments.
* testsuite/gas/arm/mve-shift-bad.l: Modify.
* testsuite/gas/arm/mve-shift-bad.s: Likewise.
* testsuite/gas/arm/mve-shift.d: Likewise.
* testsuite/gas/arm/mve-shift.s: Likewise.
opcodes * arm-dis.c (struct mopcode32 mve_opcodes): Modify the mask for
cases MVE_SQRSHRL and MVE_UQRSHLL.
(print_insn_mve): Add case for specifier 'k' to check
specific bit of the instruction.
PR 24854
* arc-dis.c (arc_insn_length): Return 0 rather than aborting when
encountering an unknown machine type.
(print_insn_arc): Handle arc_insn_length returning 0. In error
cases return -1 rather than calling abort.
The flag is supposed to be used in templates which allow for both a
"short" and a "long" format memory operand. Drop it from templates not
matching this pattern. In the control/status word cases it was (ab)used
in place of the intended IgnoreSize.
Previously GAS would accept .u32, .u16 and .u8 suffixes to the VQ(R)DMLAH and VQ(R)DMLASH
instructions, however the Armv8.1-M Mainline specification states that these functions only
have signed variations (.s32, .s16 and .s8 suffixes).
This is documented here:
https://static.docs.arm.com/ddi0553/bh/DDI0553B_h_armv8m_arm.pdf?_ga=2.143079093.1892401233.1563295591-999473562.1560847439#page=1183
gas * config/tc-arm.c (do_mve_vqdmlah): Use N_S_32 macro.
(do_neon_qrdmlah): Use N_S_32 macro.
* testsuite/gas/arm/mve-vqdmlah-bad.d: New test.
* testsuite/gas/arm/mve-vqdmlah-bad.l: New test.
* testsuite/gas/arm/mve-vqdmlah-bad.s: New test.
* testsuite/gas/arm/mve-vqdmlah.d: Remove unsigned instruction tests.
* testsuite/gas/arm/mve-vqdmlah.s: Remove unsigned instruction tests.
* testsuite/gas/arm/mve-vqdmlash-bad.d: New test.
* testsuite/gas/arm/mve-vqdmlash-bad.l: New test.
* testsuite/gas/arm/mve-vqdmlash-bad.s: New test.
* testsuite/gas/arm/mve-vqdmlash.d: Remove unsigned instruction tests.
* testsuite/gas/arm/mve-vqdmlash.s: Remove unsigned instruction tests.
opcodes * arm-dis.c: Only accept signed variants of VQ(R)DMLAH and VQ(R)DMLASH
instructions.
New instruction are added, and some of them are overlapping. Update
disassembler to correctly recognize them. Introduce nps400 option.
opcodes/
xxxx-xx-xx Claudiu Zissulescu <claziss@synopsys.com>
* arc-dis.c (skip_this_opcode): Check also for 0x07 major opcodes,
and MPY class instructions.
(parse_option): Add nps400 option.
(print_arc_disassembler_options): Add nps400 info.
gas/
xxxx-xx-xx Claudiu Zissulescu <claziss@synopsys.com>
* testsuite/gas/arc/nps400-6.d: Update test.
This patch changes the eBPF CPU description to prefer the register
names %r0 and %r6 instead of %a and %ctx when disassembling. This
matches better with the current practice, vs. cBPF.
It also updates the GAS tests in order to reflect this change.
Tested in a x86_64 host.
cpu/ChangeLog:
2019-07-19 Jose E. Marchesi <jose.marchesi@oracle.com>
* bpf.cpu (h-gpr): when disassembling, use %r0 and %r6 instead of
%a and %ctx.
opcodes/ChangeLog:
2019-07-19 Jose E. Marchesi <jose.marchesi@oracle.com>
* bpf-desc.c: Regenerated.
gas/ChangeLog:
2019-07-19 Jose E. Marchesi <jose.marchesi@oracle.com>
* testsuite/gas/bpf/alu.d: Use %r6 instead of %ctx.
* testsuite/gas/bpf/lddw-be.d: Likewise.
* testsuite/gas/bpf/lddw.d: Likewise.
* testsuite/gas/bpf/alu-be.d: Likewise.
* testsuite/gas/bpf/alu32.d: Likewise.
This was supposed to also be removed by c48dadc9a8 ('x86: drop "mem"
operand type attribute'). It's odd enough that this hasn't caused
build issues, considering the careful use of OTunused (apparently to
avoid "missing initializer" warnings).
To avoid such happening again introduce compile time consistency
checks.
... instead of an operand type bit: It's an insn property, not an
operand one. There's just one actual change to be made to the
templates: Most are now required to have the (unswapped) destination go
into ModR/M.rm, so VMOVD template needs its opcode adjusted accordingly
and its operands swapped. {,V}MOVS{S,D}, otoh, are left alone in this
regard, as otherwise generated code would differ from what we've been
producing so far (which I don't think is wanted).
Take the opportunity and add a missing IgnoreSize to pextrb (leading to
an error in 16-bit mode), and take the liberty to once again drop stray
IgnoreSize attributes from lines changed and neighboring related ones.
They're the only exception to there generally being no mix of register
kinds possible in an insn operand template, and there being two bits per
operand for their representation is also quite wasteful, considering the
low number of uses. Fold both bits and deal with the little bit of
fallout.
Also take the liberty and drop dead code trying to set REX_B: No segment
register has RegRex set on it.
Additionally I was quite surprised that PUSH/POP with the permitted
segment registers is not covered by the test cases. Add the missing
pieces.
This patch fixes the eBPF CPU description in order to reflect the
right explicit arguments passed to the ldabs{b,h,w,dw} instructions,
updates the corresponding GAS tests, and updates the BPF section of
the GAS manual.
cpu/ChangeLog:
2019-07-15 Jose E. Marchesi <jose.marchesi@oracle.com>
* bpf.cpu (dlabs): New pmacro.
(dlind): Likewise.
opcodes/ChangeLog:
2019-07-15 Jose E. Marchesi <jose.marchesi@oracle.com>
* bpf-desc.c: Regenerate.
* bpf-opc.c: Likewise.
* bpf-opc.h: Likewise.
gas/ChangeLog:
2019-07-15 Jose E. Marchesi <jose.marchesi@oracle.com>
* testsuite/gas/bpf/mem.s: ldabs instructions do not take a `src'
register as an argument.
* testsuite/gas/bpf/mem.d: Updated accordingly.
* testsuite/gas/bpf/mem-be.d: Likewise.
* doc/c-bpf.texi (BPF Opcodes): Update to reflect the correct
explicit arguments to ldabs and ldind instructions.
The eBPF non-generic load instructions ldind{b,h,w,dw} and
ldabs{b,h,w,dw} do not take an explicit destination register as an
argument. Instead, they put the loaded value in %r0, implicitly.
This patch fixes the CPU BPF description to not expect a 'dst'
argument in these arguments, regenerates the corresponding files in
opcodes, and updates the impacted GAS tests.
Tested in a x86-64 host.
cpu/ChangeLog:
2019-07-14 Jose E. Marchesi <jose.marchesi@oracle.com>
* bpf.cpu (dlsi): ldabs and ldind instructions do not take an
explicit 'dst' argument.
opcodes/ChangeLog:
2019-07-14 Jose E. Marchesi <jose.marchesi@oracle.com>
* bpf-desc.c: Regenerate.
* bpf-opc.c: Likewise.
gas/ChangeLog:
2019-07-14 Jose E. Marchesi <jose.marchesi@oracle.com>
* testsuite/gas/bpf/mem.s: Do not use explicit arguments for
ldabs and ldind instructions.
* testsuite/gas/bpf/mem.d: Updated accordingly.
* testsuite/gas/bpf/mem-be.d: Likewise.
Older gcc warns, arguably incorrectly, about name collisions between
global functions and function-local variable names. Consesus has been
to rename local variables whenever this is spotted, hence committed as
obvious. Note the pre-existing variable named idx; "index_operand"
seemed logical given the context.
* arm-dis.c (print_insn_coprocessor): Rename index to
index_operand.
From Kito Cheng <kito.cheng@sifive.com>
gas/ChangeLog
* doc/c-riscv.texi (Instruction Formats): Add r4 type.
* testsuite/gas/riscv/insn.d: Add testcase for r4 type.
* testsuite/gas/riscv/insn.s: Ditto.
* doc/c-riscv.texi (Instruction Formats): Add b and j type.
* testsuite/gas/riscv/insn.d: Add test case for b and j type.
* testsuite/gas/riscv/insn.s: Ditto.
* testsuite/gas/riscv/insn.s: Correct instruction type for load
and store.
* testsuite/gas/riscv/insn.d: Using regular expression to match
address.
* doc/c-riscv.texi (Instruction Formats): Fix encoding table for SB
type and fix typo.
opcode/ChangeLog
* riscv-opc.c (riscv_insn_types): Add r4 type.
* riscv-opc.c (riscv_insn_types): Add b and j type.
* opcodes/riscv-opc.c (riscv_insn_types): Remove incorrect
format for sb type and correct s type.
The entry for the FMOV alias of FCPY was missing C_SCAN_MOVPRFX.
(The entry for FCPY itself was OK.)
This was the only /m-predicated instruction I could see that was
missing the flag.
2019-07-02 Richard Sandiford <richard.sandiford@arm.com>
opcodes/
* aarch64-tbl.h (aarch64_opcode): Set C_SCAN_MOVPRFX for the
SVE FMOV alias of FCPY.
gas/
* testsuite/gas/aarch64/sve-movprfx_27.s,
* testsuite/gas/aarch64/sve-movprfx_27.d: New test.
SVE FCVTZS, FCVTZU, SCVTF and UCVTF need the same treatment as FCVT:
the register size used in a predicated MOVPRFX must be the wider of
the destination and source sizes.
Since I was adding a (supposedly) complete set of tests for converts,
it seemed more consistent to add a complete set of tests for shifts
as well, even though there's no bug to fix there.
2019-07-02 Richard Sandiford <richard.sandiford@arm.com>
opcodes/
* aarch64-tbl.h (aarch64_opcode_table): Add C_MAX_ELEM flags
to SVE fcvtzs, fcvtzu, scvtf and ucvtf entries.
gas/
* testsuite/gas/aarch64/sve-movprfx_26.s: Also test FCVTZS, FCVTZU,
SCVTF, UCVTF, LSR and ASR.
* testsuite/gas/aarch64/sve-movprfx_26.d: Update accordingly.
* testsuite/gas/aarch64/sve-movprfx_26.l: Likewise.
One of the MOVPRFX tests has:
output register of preceding `movprfx' used as input at operand 3 -- `cpy z1.d,p1/m,x1'
But X1 and Z1 are not the same register, so the instruction is
actually OK.
2019-07-02 Richard Sandiford <richard.sandiford@arm.com>
opcodes/
* aarch64-opc.c (verify_constraints): Skip GPRs when scanning the
registers in an instruction prefixed by MOVPRFX.
gas/
* testsuite/gas/aarch64/sve-movprfx_25.s: Allow CPY Z1.D.P1/M,X1
to be prefixed by MOVPRFX.
* testsuite/gas/aarch64/sve-movprfx_25.d: Update accordingly.
* testsuite/gas/aarch64/sve-movprfx_25.l: Likewise.
Alan Modra
Jan Beulich
Dr N.W. Filardo
Mihail Ionescu
Jim Wilson
H.J. Lu
Matthew Malcomson
Nick Clifton
Delia Burduv
Simon Marchi
Phil Blundell
Miod Vallat
Srinath Parvathaneni
Kyrylo Tkachov
Phillipe Antoine
Barnaby Wilks
Claudiu Zissulescu
Jose E. Marchesi
Hans-Peter Nilsson
Richard Sandiford