RISC-V specifies multiple sizes for addressable memory and Linux probes for
the machine's support at startup via the satp CSR register (done in
csr.c:validate_vm).
As per the specification, sv64 must support sv57, which in turn must
support sv48...etc. So we can restrict machine support by simply setting the
"highest" supported mode and the bare mode is always supported.
You can set the satp mode using the new properties "sv32", "sv39", "sv48",
"sv57" and "sv64" as follows:
-cpu rv64,sv57=on # Linux will boot using sv57 scheme
-cpu rv64,sv39=on # Linux will boot using sv39 scheme
-cpu rv64,sv57=off # Linux will boot using sv48 scheme
-cpu rv64 # Linux will boot using sv57 scheme by default
We take the highest level set by the user:
-cpu rv64,sv48=on,sv57=on # Linux will boot using sv57 scheme
We make sure that invalid configurations are rejected:
-cpu rv64,sv39=off,sv48=on # sv39 must be supported if higher modes are
# enabled
We accept "redundant" configurations:
-cpu rv64,sv48=on,sv57=off # Linux will boot using sv48 scheme
And contradictory configurations:
-cpu rv64,sv48=on,sv48=off # Linux will boot using sv39 scheme
Co-Developed-by: Ludovic Henry <ludovic@rivosinc.com>
Signed-off-by: Ludovic Henry <ludovic@rivosinc.com>
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-ID: <20230303131252.892893-4-alexghiti@rivosinc.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Zicbom is the Cache-Block Management extension defined in the already
ratified RISC-V Base Cache Management Operation (CBO) ISA extension [1].
The extension contains three instructions: cbo.clean, cbo.flush and
cbo.inval. All of them must be implemented in the same group as LQ and
cbo.zero due to overlapping patterns.
All these instructions can throw a Illegal Instruction/Virtual
Instruction exception, similar to the existing cbo.zero. The same
check_zicbo_envcfg() is used to handle these exceptions.
Aside from that, these instructions also need to handle page faults and
guest page faults. This is done in a new check_zicbom_access() helper.
As with Zicboz, the cache block size for Zicbom is also configurable.
Note that the spec determines that Zicbo[mp] and Zicboz can have
different cache sizes (Section 2.7 of [1]), so we also include a
'cbom_blocksize' to go along with the existing 'cboz_blocksize'. They
are set to the same size, so unless users want to play around with the
settings both sizes will be the same.
[1] https://github.com/riscv/riscv-CMOs/blob/master/specifications/cmobase-v1.0.1.pdf
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Co-developed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Signed-off-by: Christoph Muellner <cmuellner@linux.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230224132536.552293-4-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The RISC-V base cache management operation (CBO) ISA extension has been
ratified. It defines three extensions: Cache-Block Management, Cache-Block
Prefetch and Cache-Block Zero. More information about the spec can be
found at [1].
Let's start by implementing the Cache-Block Zero extension, Zicboz. It
uses the cbo.zero instruction that, as with all CBO instructions that
will be added later, needs to be implemented in an overlap group with
the LQ instruction due to overlapping patterns.
cbo.zero throws a Illegal Instruction/Virtual Instruction exception
depending on CSR state. This is also the case for the remaining cbo
instructions we're going to add next, so create a check_zicbo_envcfg()
that will be used by all Zicbo[mz] instructions.
[1] https://github.com/riscv/riscv-CMOs/blob/master/specifications/cmobase-v1.0.1.pdf
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Co-developed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Signed-off-by: Christoph Muellner <cmuellner@linux.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Message-ID: <20230224132536.552293-3-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Weiwei Li <liweiwei@iscas.ac.cn> says:
This patchset adds support svadu extension. It also fixes some
relationship between *envcfg fields and Svpbmt/Sstc extensions.
Specification for Svadu extension can be found in:
https://github.com/riscv/riscv-svadu
* b4-shazam-merge:
target/riscv: Export Svadu property
target/riscv: Add *envcfg.HADE related check in address translation
target/riscv: Add *envcfg.PBMTE related check in address translation
target/riscv: Add csr support for svadu
target/riscv: Fix the relationship of PBMTE/STCE fields between menvcfg and henvcfg
target/riscv: Fix the relationship between menvcfg.PBMTE/STCE and Svpbmt/Sstc extensions
Message-ID: <20230224040852.37109-1-liweiwei@iscas.ac.cn>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Add ext_svadu property
Add HADE field in *envcfg:
* menvcfg.HADE is read-only zero if Svadu is not implemented.
* henvcfg.HADE is read-only zero if menvcfg.HADE is zero.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20230224040852.37109-4-liweiwei@iscas.ac.cn>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The spec can be found in https://github.com/riscv/riscv-zicond.
Two instructions are added:
- czero.eqz: Moves zero to a register rd, if the condition rs2 is
equal to zero, otherwise moves rs1 to rd.
- czero.nez: Moves zero to a register rd, if the condition rs2 is
nonzero, otherwise moves rs1 to rd.
Signed-off-by: Weiwei Li <liweiwei@iscas.ac.cn>
Signed-off-by: Junqiang Wang <wangjunqiang@iscas.ac.cn>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Message-ID: <20230221091009.36545-1-liweiwei@iscas.ac.cn>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
RISC-V defines a handful of extensions related to floating point, along
with various relationships between these and other extensions. This
patch set adds support for the Zvfh, Zvhfmin, and Zve64d extensions;
along with a handful of fixes and cleanups related to the other
floating-point extension relationships.
* b4-shazam-merge
target/riscv: Expose properties for Zv* extensions
target/riscv: Simplify check for EEW = 64 in trans_rvv.c.inc
target/riscv: Fix check for vector load/store instructions when EEW=64
target/riscv: Add support for Zvfh/zvfhmin extensions
target/riscv: Remove rebundunt check for zve32f and zve64f
target/riscv: Replace check for F/D to Zve32f/Zve64d in trans_rvv.c.inc
target/riscv: Simplify check for Zve32f and Zve64f
target/riscv: Indent fixes in cpu.c
target/riscv: Add propertie check for Zvfh{min} extensions
target/riscv: Fix relationship between V, Zve*, F and D
target/riscv: Add cfg properties for Zv* extensions
target/riscv: Simplify the check for Zfhmin and Zhinxmin
target/riscv: Fix the relationship between Zhinxmin and Zhinx
target/riscv: Fix the relationship between Zfhmin and Zfh
Message-ID: <20230215020539.4788-1-liweiwei@iscas.ac.cn>
[Palmer: commit text]
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
The attribute is no longer used since we can retrieve all the enabled
features in the hart by using cpu->cfg instead.
Remove env->feature, riscv_feature() and riscv_set_feature(). We also
need to bump vmstate_riscv_cpu version_id and minimal_version_id since
'features' is no longer being migrated.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-ID: <20230222185205.355361-11-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
RISCV_FEATURE_MMU is set whether cpu->cfg.mmu is set, so let's just use
the flag directly instead.
With this change the enum is also removed. It is worth noticing that
this enum, and all the RISCV_FEATURES_* that were contained in it,
predates the existence of the cpu->cfg object. Today, using cpu->cfg is
an easier way to retrieve all the features and extensions enabled in the
hart.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-ID: <20230222185205.355361-10-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
RISCV_FEATURE_PMP is being set via riscv_set_feature() by mirroring the
cpu->cfg.pmp flag. Use the flag instead.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-ID: <20230222185205.355361-8-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
RISCV_FEATURE_EPMP is always set to the same value as the cpu->cfg.epmp
flag. Use the flag directly.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-ID: <20230222185205.355361-7-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
RISCV_FEATURE_DEBUG will always follow the value defined by
cpu->cfg.debug flag. Read the flag instead.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-ID: <20230222185205.355361-5-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
At this moment, and apparently since ever, we have no way of enabling
RISCV_FEATURE_MISA. This means that all the code from write_misa(), all
the nuts and bolts that handles how to properly write this CSR, has
always been a no-op as well because write_misa() will always exit
earlier.
This seems to be benign in the majority of cases. Booting an Ubuntu
'virt' guest and logging all the calls to 'write_misa' shows that no
writes to MISA CSR was attempted. Writing MISA, i.e. enabling/disabling
RISC-V extensions after the machine is powered on, seems to be a niche
use.
After discussions in the mailing list, most notably in [1], we reached
the consensus that this code is not suited to be exposed to users
because it's not well tested, but at the same time removing it is a bit
extreme because we would like to fix it, and it's easier to do so with
the code available to use instead of fetching it from git log.
The approach taken here is to get rid of RISCV_FEATURE_MISA altogether
and use a new experimental flag called x-misa-w. The default value is
false, meaning that we're keeping the existing behavior of doing nothing
if a write_misa() is attempted. As with any existing experimental flag,
x-misa-w is also a temporary flag that we need to remove once we fix
write_misa().
[1] https://lists.gnu.org/archive/html/qemu-devel/2023-02/msg05092.html
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Weiwei Li<liweiwei@iscas.ac.cn>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-ID: <20230222185205.355361-4-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
We're going to do changes that requires accessing the RISCVCPUConfig
struct from the RISCVCPU, having access only to a CPURISCVState 'env'
pointer. Add a helper to make the code easier to read.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-ID: <20230222185205.355361-2-dbarboza@ventanamicro.com>
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20221217172907.8364-7-philmd@linaro.org>
The 'hwaddr' type is only available / meaningful on system emulation.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216215519.5522-6-philmd@linaro.org>
The 'hwaddr' type is only available / meaningful on system emulation.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221216215519.5522-5-philmd@linaro.org>
This patch adds support for the XTheadFmv ISA extension.
The patch uses the T-Head specific decoder and translation.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230131202013.2541053-14-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds the T-Head C906 to the list of known CPUs.
Selecting this CPUs will automatically enable the available
ISA extensions of the CPUs (incl. vendor extensions).
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230131202013.2541053-13-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the T-Head FMemIdx instructions.
The patch uses the T-Head specific decoder and translation.
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230131202013.2541053-11-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the T-Head MemIdx instructions.
The patch uses the T-Head specific decoder and translation.
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230131202013.2541053-10-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the T-Head MemPair instructions.
The patch uses the T-Head specific decoder and translation.
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230131202013.2541053-9-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the T-Head MAC instructions.
The patch uses the T-Head specific decoder and translation.
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230131202013.2541053-8-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the XTheadCondMov ISA extension.
The patch uses the T-Head specific decoder and translation.
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230131202013.2541053-7-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the XTheadBs ISA extension.
The patch uses the T-Head specific decoder and translation.
Co-developed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230131202013.2541053-6-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the XTheadBb ISA extension.
The patch uses the T-Head specific decoder and translation.
Co-developed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230131202013.2541053-5-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the XTheadBa ISA extension.
The patch uses the T-Head specific decoder and translation.
Co-developed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230131202013.2541053-4-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the XTheadSync ISA extension.
The patch uses the T-Head specific decoder and translation.
The implementation introduces a helper to execute synchronization tasks:
helper_tlb_flush_all() performs a synchronized TLB flush on all CPUs.
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Message-Id: <20230131202013.2541053-3-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the XTheadCmo ISA extension.
To avoid interfering with standard extensions, decoder and translation
are in its own xthead* specific files.
Future patches should be able to easily add additional T-Head extension.
The implementation does not have much functionality (besides accepting
the instructions and not qualifying them as illegal instructions if
the hart executes in the required privilege level for the instruction),
as QEMU does not model CPU caches and instructions are documented
to not raise any exceptions.
Co-developed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230131202013.2541053-2-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
There is an informal contract between the cpu_init() functions and
riscv_cpu_realize(): if cpu->env.misa_ext is zero, assume that the
default settings were loaded via register_cpu_props() and do validations
to set env.misa_ext. If it's not zero, skip this whole process and
assume that the board somehow did everything.
At this moment, all SiFive CPUs are setting a non-zero misa_ext during
their cpu_init() and skipping a good chunk of riscv_cpu_realize(). This
causes problems when the code being skipped in riscv_cpu_realize()
contains fixes or assumptions that affects all CPUs, meaning that SiFive
CPUs are missing out.
To allow this code to not be skipped anymore, all the cpu->cfg.ext_*
attributes needs to be set during cpu_init() time. At this moment this
is being done in register_cpu_props(). The SiFive boards are setting
their own extensions during cpu_init() though, meaning that they don't
want all the defaults from register_cpu_props().
Let's move the contract between *_cpu_init() and riscv_cpu_realize() to
register_cpu_props(). Inside this function we'll check if
cpu->env.misa_ext was set and, if that's the case, set all relevant
cpu->cfg.ext_* attributes, and only that. Leave the 'misa_ext' = 0 case
as is today, i.e. loading all the defaults from riscv_cpu_extensions[].
register_cpu_props() can then be called by all the cpu_init() functions,
including the SiFive ones. This will make all CPUs behave more in line
with what riscv_cpu_realize() expects.
This will also make the cpu_init() functions even more alike, but at this
moment we would need some design changes in how we're initializing
extensions/attributes (e.g. some CPUs are setting cfg options after
register_cpu_props(), so we can't simply add the function to a common
post_init() hook) to make a common cpu_init() code across all CPUs.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20230113175230.473975-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
At present for some unknown reason the HTIF registers (fromhost &
tohost) are defined in the RISC-V CPUArchState. It should really
be put in the HTIFState struct as it is only meaningful to HTIF.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221229091828.1945072-6-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
This patch adds support for the Zawrs ISA extension.
Given the current (incomplete) implementation of reservation sets
there seems to be no way to provide a full emulation of the WRS
instruction (wake on reservation set invalidation or timeout or
interrupt). Therefore, we just exit the TB and return to the main loop.
The specification can be found here:
https://github.com/riscv/riscv-zawrs/blob/main/zawrs.adoc
Note, that the Zawrs extension is frozen, but not ratified yet.
Changes since v3:
* Remove "RFC" since the extension is frozen
* Rebase on master and fix integration issues
* Fix entry ordering in extension list
Changes since v2:
* Rebase on master and resolve conflicts
* Adjustments according to a specification change
* Inline REQUIRE_ZAWRS() since it has only one user
Changes since v1:
* Adding zawrs to the ISA string that is passed to the kernel
Signed-off-by: Christoph Müllner <christoph.muellner@vrull.eu>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221005144948.3421504-1-christoph.muellner@vrull.eu>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Avoid calling riscv_itrigger_enabled() when calculate the tbflags.
As the itrigger enable status can only be changed when write
tdata1, migration load or itrigger fire, update env->itrigger_enabled
at these places.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221013062946.7530-5-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The max count in itrigger can be 0x3FFF, which will cause a no trivial
translation and execution overload.
When icount is enabled, QEMU provides API that can fetch guest
instruction number. Thus, we can set an timer for itrigger with
the count as deadline.
Only when timer expires or priviledge mode changes, do lazy update
to count.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221013062946.7530-3-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
When icount is not enabled, there is no API in QEMU that can get the
guest instruction number.
Translate the guest code in a way that each TB only has one instruction.
After executing the instruction, decrease the count by 1 until it reaches 0
where the itrigger fires.
Note that only when priviledge matches the itrigger configuration,
the count will decrease.
Signed-off-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221013062946.7530-2-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Smstateen extension specifies a mechanism to close
the potential covert channels that could cause security issues.
This patch adds the CSRs defined in the specification and
the corresponding predicates and read/write functions.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221016124726.102129-2-mchitale@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Convert the riscv CPU class to use 3-phase reset, so it doesn't
need to use device_class_set_parent_reset() any more.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Edgar E. Iglesias <edgar@zeroasic.com>
Reviewed-by: Taylor Simpson <tsimpson@quicinc.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-id: 20221124115023.2437291-15-peter.maydell@linaro.org
It's always better to convey the type of a pointer if at all
possible. So let's add the DumpState typedef to typedefs.h and move
the dump note functions from the opaque pointers to DumpState
pointers.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
CC: Peter Maydell <peter.maydell@linaro.org>
CC: Cédric Le Goater <clg@kaod.org>
CC: Daniel Henrique Barboza <danielhb413@gmail.com>
CC: David Gibson <david@gibson.dropbear.id.au>
CC: Greg Kurz <groug@kaod.org>
CC: Palmer Dabbelt <palmer@dabbelt.com>
CC: Alistair Francis <alistair.francis@wdc.com>
CC: Bin Meng <bin.meng@windriver.com>
CC: Cornelia Huck <cohuck@redhat.com>
CC: Thomas Huth <thuth@redhat.com>
CC: Richard Henderson <richard.henderson@linaro.org>
CC: David Hildenbrand <david@redhat.com>
Acked-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20220811121111.9878-2-frankja@linux.ibm.com>
Replace type2_trigger_t with the real tdata1, tdata2, and tdata3 CSRs,
which allows us to support more types of triggers in the future.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
Message-Id: <20220909134215.1843865-4-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Current RISC-V debug assumes that only type 2 trigger is supported.
To allow more types of triggers to be supported in the future
(e.g. type 6 trigger, which is similar to type 2 trigger with additional
functionality), we should determine the trigger type from tdata1.type.
RV_MAX_TRIGGERS is also introduced in replacement of TRIGGER_TYPE2_NUM.
Signed-off-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com>
[bmeng: fixed MXL_RV128 case, and moved macros to the following patch]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220909134215.1843865-2-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Instead of using our properties to set a config value which then might
be used to set the resetvec (depending on your timing), let's instead
just set the resetvec directly in the env struct.
This allows us to set the reset vec from the command line with:
-global driver=riscv.hart_array,property=resetvec,value=0x20000400
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220914101108.82571-2-alistair.francis@wdc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The Sscofpmf ('Ss' for Privileged arch and Supervisor-level extensions,
and 'cofpmf' for Count OverFlow and Privilege Mode Filtering)
extension allows the perf to handle overflow interrupts and filtering
support. This patch provides a framework for programmable
counters to leverage the extension. As the extension doesn't have any
provision for the overflow bit for fixed counters, the fixed events
can also be monitoring using programmable counters. The underlying
counters for cycle and instruction counters are always running. Thus,
a separate timer device is programmed to handle the overflow.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-Id: <20220824221701.41932-2-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
vstimecmp CSR allows the guest OS or to program the next guest timer
interrupt directly. Thus, hypervisor no longer need to inject the
timer interrupt to the guest if vstimecmp is used. This was ratified
as a part of the Sstc extension.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-Id: <20220824221357.41070-4-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
stimecmp allows the supervisor mode to update stimecmp CSR directly
to program the next timer interrupt. This CSR is part of the Sstc
extension which was ratified recently.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-Id: <20220824221357.41070-3-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Historically, The mtime/mtimecmp has been part of the CPU because
they are per hart entities. However, they actually belong to aclint
which is a MMIO device.
Move them to the ACLINT device. This also emulates the real hardware
more closely.
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Message-Id: <20220824221357.41070-2-atishp@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
The arch review of AIA spec is completed and we now have official
extension names for AIA: Smaia (M-mode AIA CSRs) and Ssaia (S-mode
AIA CSRs).
Refer, section 1.6 of the latest AIA v0.3.1 stable specification at
https://github.com/riscv/riscv-aia/releases/download/0.3.1-draft.32/riscv-interrupts-032.pdf)
Based on above, we update QEMU RISC-V to:
1) Have separate config options for Smaia and Ssaia extensions
which replace RISCV_FEATURE_AIA in CPU features
2) Not generate AIA INTC compatible string in virt machine
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20220820042958.377018-1-apatel@ventanamicro.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Added support for RISC-V PAUSE instruction from Zihintpause extension,
enabled by default.
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Dao Lu <daolu@rivosinc.com>
Message-Id: <20220725034728.2620750-2-daolu@rivosinc.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
According to v-spec, mask agnostic behavior can be either kept as
undisturbed or set elements' bits to all 1s. To distinguish the
difference of mask policies, QEMU should be able to simulate the mask
agnostic behavior as "set mask elements' bits to all 1s".
There are multiple possibility for agnostic elements according to
v-spec. The main intent of this patch-set tries to add option that
can distinguish between mask policies. Setting agnostic elements to
all 1s allows QEMU to express this.
This is the first commit regarding the optional mask agnostic
behavior. Follow-up commits will add this optional behavior
for all rvv instructions.
Signed-off-by: eop Chen <eop.chen@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Reviewed-by: Weiwei Li <liweiwei@iscas.ac.cn>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <165570784143.17634.35095816584573691-1@git.sr.ht>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
We should write transformed instruction encoding of the trapped
instruction in [m|h]tinst CSR at time of taking trap as defined
by the RISC-V privileged specification v1.12.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Acked-by: dramforever <dramforever@live.com>
Message-Id: <20220630061150.905174-2-apatel@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Alexandre Ghiti
Christoph Muellner
Palmer Dabbelt
Weiwei Li
Daniel Henrique Barboza
Philippe Mathieu-Daudé
Christoph Müllner
Bin Meng
LIU Zhiwei
Mayuresh Chitale
Peter Maydell
Janosch Frank
Frank Chang
Alistair Francis
Atish Patra
Anup Patel
Dao Lu
Yueh-Ting (eop) Chen